mirror of
https://github.com/torvalds/linux.git
synced 2026-07-28 01:55:51 +02:00
Linux kernel source tree
5e1663810e
The TDC is currently hardcoded enabled. This means that even for lower
CAN-FD data bitrates (with a DBRP (data bitrate prescaler) > 2) a TDC
is configured. This leads to a bus-off condition.
ISO 11898-1 section 11.3.3 says "Transmitter delay compensation" (TDC)
is only applicable if DBRP is 1 or 2.
To fix the problem, switch the driver to use the TDC calculation
provided by the CAN driver framework (which respects ISO 11898-1
section 11.3.3). This has the positive side effect that userspace can
control TDC as needed.
Demonstration of the feature in action:
| $ ip link set can0 up type can bitrate 125000 dbitrate 500000 fd on
| $ ip -details link show can0
| 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can <FD> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
| bitrate 125000 sample-point 0.875
| tq 50 prop-seg 69 phase-seg1 70 phase-seg2 20 sjw 10 brp 2
| mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1
| dbitrate 500000 dsample-point 0.875
| dtq 125 dprop-seg 6 dphase-seg1 7 dphase-seg2 2 dsjw 1 dbrp 5
| mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1
| tdcv 0..63 tdco 0..63
| clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0
| $ ip link set can0 up type can bitrate 1000000 dbitrate 4000000 fd on
| $ ip -details link show can0
| 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can <FD,TDC-AUTO> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
| bitrate 1000000 sample-point 0.750
| tq 25 prop-seg 14 phase-seg1 15 phase-seg2 10 sjw 5 brp 1
| mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1
| dbitrate 4000000 dsample-point 0.700
| dtq 25 dprop-seg 3 dphase-seg1 3 dphase-seg2 3 dsjw 1 dbrp 1
| tdco 7
| mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1
| tdcv 0..63 tdco 0..63
| clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0
There has been some confusion about the MCP2518FD using a relative or
absolute TDCO due to the datasheet specifying a range of [-64,63]. I
have a custom board with a 40 MHz clock and an estimated loop delay of
100 to 216 ns. During testing at a data bit rate of 4 Mbit/s I found
that using can_get_relative_tdco() resulted in bus-off errors. The
final TDCO value was 1 which corresponds to a 10% SSP in an absolute
configuration. This behavior is expected if the TDCO value is really
absolute and not relative. Using priv->can.tdc.tdco instead results in
a final TDCO of 8, setting the SSP at exactly 80%. This configuration
works.
The automatic, manual, and off TDC modes were tested at speeds up to,
and including, 8 Mbit/s on real hardware and behave as expected.
Fixes:
|
||
|---|---|---|
| arch | ||
| block | ||
| certs | ||
| crypto | ||
| Documentation | ||
| drivers | ||
| fs | ||
| include | ||
| init | ||
| io_uring | ||
| ipc | ||
| kernel | ||
| lib | ||
| LICENSES | ||
| mm | ||
| net | ||
| rust | ||
| samples | ||
| scripts | ||
| security | ||
| sound | ||
| tools | ||
| usr | ||
| virt | ||
| .clang-format | ||
| .clippy.toml | ||
| .cocciconfig | ||
| .editorconfig | ||
| .get_maintainer.ignore | ||
| .gitattributes | ||
| .gitignore | ||
| .mailmap | ||
| .rustfmt.toml | ||
| COPYING | ||
| CREDITS | ||
| Kbuild | ||
| Kconfig | ||
| MAINTAINERS | ||
| Makefile | ||
| README | ||
Linux kernel
============
There are several guides for kernel developers and users. These guides can
be rendered in a number of formats, like HTML and PDF. Please read
Documentation/admin-guide/README.rst first.
In order to build the documentation, use ``make htmldocs`` or
``make pdfdocs``. The formatted documentation can also be read online at:
https://www.kernel.org/doc/html/latest/
There are various text files in the Documentation/ subdirectory,
several of them using the reStructuredText markup notation.
Please read the Documentation/process/changes.rst file, as it contains the
requirements for building and running the kernel, and information about
the problems which may result by upgrading your kernel.