pdsc_adminq_wait_and_dec_once_unused() busy-waits for adminq_refcnt to
drop to one:
while (!refcount_dec_if_one(&pdsc->adminq_refcnt))
cpu_relax();
The refcount is held by pdsc_adminq_post() for the duration of an
in-flight command, which can wait up to devcmd_timeout seconds
(PDS_CORE_DEVCMD_TIMEOUT is 5) for the hardware to complete. cpu_relax()
is not a reschedule point, so on a non-preemptible kernel this loop can
spin on the CPU for several seconds, starving other tasks on that core.
Add cond_resched() to the loop so the waiter yields to other runnable
tasks while it polls, keeping cpu_relax() as the busy-wait hint between
checks.
Fixes: 7e82a8745b ("pds_core: Prevent race issues involving the adminq")
Reported-by: sashiko-bot <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/patchset/20260629200358.2626129-1-nikhil.rao%40amd.com?part=2
Signed-off-by: Nikhil P. Rao <nikhil.rao@amd.com>
Reviewed-by: Eric Joyner <eric.joyner@amd.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://patch.msgid.link/20260714201456.1776153-1-nikhil.rao@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikhil P. Rao says:
====================
pds_core: fix use-after-free on workqueue during remove
This series fixes a use-after-free on the workqueue during driver remove.
Patch 1 fixes a pre-existing deadlock between the PCI reset worker and
pdsc_remove() that was identified during review of v1.
Patch 2 is the reworked UAF fix that moves destroy_workqueue() after
pdsc_teardown() and adds proper work synchronization.
====================
Link: https://patch.msgid.link/20260714180223.1642792-1-nikhil.rao@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In pdsc_remove(), the workqueue is destroyed before pdsc_teardown()
is called. This ordering allows two paths to queue work on the
destroyed workqueue:
1. If pdsc_teardown() -> pdsc_devcmd_reset() times out, the error
path in pdsc_devcmd_locked() queues health_work.
2. A NotifyQ event can trigger the ISR and queue work before free_irq()
is called in pdsc_teardown().
Fix by moving destroy_workqueue() after pdsc_teardown() so the
workqueue outlives every queuer; destroy_workqueue() then flushes any
work still pending.
Draining the queued work also requires ordering the teardown so the
resources that work touches are freed last:
- In pdsc_qcq_free(), after freeing the interrupt, cancel_work_sync()
the queue's work and only then clear qcq->intx, so
pdsc_process_adminq()'s read of qcq->intx for interrupt-credit
return cannot race with the clear.
- Free adminqcq before notifyqcq: the shared adminq ISR is released
when adminqcq is freed, and the adminq work accesses notifyqcq, so
both must be stopped before notifyqcq is freed.
Fixes: 01ba61b55b ("pds_core: Add adminq processing and commands")
Reported-by: sashiko-bot <sashiko-bot@kernel.org>
Closes: https://patchwork.kernel.org/comment/27002369/
Signed-off-by: Nikhil P. Rao <nikhil.rao@amd.com>
Link: https://patch.msgid.link/20260714180223.1642792-3-nikhil.rao@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_reset_function() acquires device_lock before performing the reset.
pdsc_remove() is called by the PCI core with device_lock already held.
If pdsc_pci_reset_thread() is running when pdsc_remove() is called,
destroy_workqueue() will block waiting for the work to complete, while
the work is blocked waiting for device_lock - deadlock.
Use pci_try_reset_function() which uses pci_dev_trylock() internally.
This acquires both the device lock and the PCI config access lock
without blocking - if either lock is contended, it returns -EAGAIN
immediately. This avoids the deadlock while also ensuring proper
config space access serialization during the reset.
The pci_dev_get/put calls are also removed as they were unnecessary -
the driver-owned workqueue is destroyed in pdsc_remove(), guaranteeing
the work completes before remove returns. The PCI core holds its
reference to pci_dev throughout the entire unbind sequence.
Fixes: 81665adf25 ("pds_core: Fix pdsc_check_pci_health function to use work thread")
Reported-by: sashiko-bot <sashiko-bot@kernel.org>
Closes: https://patchwork.kernel.org/comment/27002369/
Signed-off-by: Nikhil P. Rao <nikhil.rao@amd.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20260714180223.1642792-2-nikhil.rao@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After picking up some pending patches for the kernel to work on, I
realized my name in the mailmap file somehow got mixed up. When
switching to my kernel.org Address some time ago, I had never the
intention to use a scrambled variant of Polish and German used for my
first name to be found in this file. However, so here we are. Lets fix
it for good.
Signed-off-by: Michael Grzeschik <mgr@kernel.org>
Link: https://patch.msgid.link/20260713-mailmap-v1-1-cb40979cb190@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sctp_auth_ep_add_chunkid() uses SCTP_NUM_CHUNK_TYPES (20) as the
capacity limit for ep->auth_chunk_list, allowing it to hold up to
20 chunk entries (param_hdr.length up to 24). However, the copy
destination asoc->c.auth_chunks in struct sctp_cookie is only
SCTP_AUTH_MAX_CHUNKS (16) entries (20 bytes). When more than 16
chunks are added, sctp_association_init() memcpy overflows the
destination by up to 4 bytes.
Fix by using SCTP_AUTH_MAX_CHUNKS as the capacity limit, matching
the destination capacity.
Fixes: 1f485649f5 ("[SCTP]: Implement SCTP-AUTH internals")
Signed-off-by: HanQuan <eilaimemedsnaimel@gmail.com>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/20260713032021.3491702-1-zhoujian.zja@antgroup.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Perfect FDIR filters can be added while the interface is down and are
kept on the software list for later restore. unregister_netdev() only
calls ndo_stop when the device is up, so txgbe_fdir_filter_exit() in
txgbe_close() is skipped in that case and the filters are leaked on
driver remove. Free the filter list from txgbe_remove() as well.
Fixes: 4bdb441105 ("net: txgbe: support Flow Director perfect filters")
Signed-off-by: Chenguang Zhao <zhaochenguang@kylinos.cn>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260713091911.1614795-1-chenguang.zhao@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When booting with the 'ipv6.disable=1' parameter, inet6_addr_lst
is never initialized because inet6_init() exits before addrconf_init()
is called to initialize it. An attempt to bind an RDS socket to
an ipv6 address results in a crash in __ipv6_chk_addr_and_flags()
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
RIP: 0010:__ipv6_chk_addr_and_flags+0x1df/0x7e0
Call Trace:
<TASK>
ipv6_chk_addr+0x3b/0x50
rds_tcp_laddr_check+0x155/0x3b0 [rds_tcp]
rds_trans_get_preferred+0x15d/0x2d0 [rds]
? trace_hardirqs_on+0x2d/0x110
rds_bind+0x1433/0x1d60 [rds]
? rds_remove_bound+0xd50/0xd50 [rds]
? aa_af_perm+0x250/0x250
? __might_fault+0xde/0x190
? __sys_bind+0x1dc/0x210
__sys_bind+0x1dc/0x210
? __ia32_sys_socketpair+0x100/0x100
? restore_fpregs_from_fpstate+0x53/0x100
__x64_sys_bind+0x73/0xb0
? syscall_enter_from_user_mode+0x1c/0x50
do_syscall_64+0x34/0x80
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
RIP: 0033:0x7f47f8269ea9
</TASK>
The following code reproduces the issue:
struct sockaddr_in6 addr;
s = socket(PF_RDS, SOCK_SEQPACKET, 0);
memset(&addr, 0, sizeof(addr));
inet_pton(AF_INET6, ADDRESS, &addr.sin6_addr);
addr.sin6_family = AF_INET6;
addr.sin6_port = htons(PORT);
bind(s, &addr, sizeof(addr));
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with Syzkaller.
Fixes: eee2fa6ab3 ("rds: Changing IP address internal representation to struct in6_addr")
Fixes: 1e2b44e78e ("rds: Enable RDS IPv6 support")
Signed-off-by: Ilia Gavrilov <Ilia.Gavrilov@infotecs.ru>
Reviewed-by: Allison Henderson <achender@kernel.org>
Link: https://patch.msgid.link/20260709162723.367523-1-Ilia.Gavrilov@infotecs.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
txgbe_read_eeprom_hostif() always copies round_up(length, 4) bytes
into the caller buffer, which ethtool allocates with exactly 'length'
bytes. A non-4-aligned length therefore causes an out-of-bounds write.
Copy only the remaining bytes on the final dword instead.
Signed-off-by: Chenguang Zhao <zhaochenguang@kylinos.cn>
Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Fixes: 9b97b6b563 ("net: txgbe: support getting module EEPROM by page")
Link: https://patch.msgid.link/20260713085111.1481884-1-chenguang.zhao@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tipc_udp_rcast_add() and cleanup_bearer() both update ub->rcast.list with
list_add_rcu() / list_del_rcu(), but nothing serializes them. The add runs
from the encap receive softirq (via tipc_udp_rcast_disc()) without
rtnl_lock(), so it can race the cleanup delete and corrupt the list:
list_del corruption. prev->next should be ffff8880298d7ab8,
but was ffff88802449ad38. (prev=ffff888027e3ec98)
kernel BUG at lib/list_debug.c:62!
RIP: __list_del_entry_valid_or_report+0x17a/0x200
Workqueue: events cleanup_bearer
Call Trace:
cleanup_bearer (net/tipc/udp_media.c:811)
process_one_work (kernel/workqueue.c:3302)
worker_thread (kernel/workqueue.c:3466)
The bearer can be enabled from an unprivileged user namespace, as the
TIPCv2 generic-netlink ops carry no GENL_ADMIN_PERM.
Add a spinlock to struct udp_bearer and take it around the list_add_rcu()
in tipc_udp_rcast_add() and the list_del_rcu() loop in cleanup_bearer() so
the two writers can no longer corrupt the list.
Reject a duplicate peer under the same lock before allocating, and remove
tipc_udp_is_known_peer(). The old lockless pre-check in
tipc_udp_rcast_disc() was racy: two softirqs discovering the same peer
could both find it absent and add it twice.
cleanup_bearer() runs from a workqueue after tipc_udp_disable() clears the
bearer's up bit, so an encap softirq can still reach tipc_udp_rcast_add()
and add a peer after cleanup_bearer() has already emptied the list, leaking
that entry when the bearer is freed. Mark the bearer disabled under
rcast_lock once the list is emptied and refuse further additions.
Fixes: ef20cd4dd1 ("tipc: introduce UDP replicast")
Reported-by: Xiang Mei <xmei5@asu.edu>
Suggested-by: Tung Nguyen <tung.quang.nguyen@est.tech>
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Reviewed-by: Tung Nguyen <tung.quang.nguyen@est.tech>
Link: https://patch.msgid.link/20260716025203.9332-2-bestswngs@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hardware performs packet parsing before packet transmission.
Parsing incomplete IPv4, IPv6, TCP, or UDP headers may trigger a TX
hang because the hardware parser expects additional protocol header
data that is not present in the packet.
The hardware performs additional PTP parsing on UDP packets identified
by destination ports 319/320 at the expected UDP destination port
offset.
If such a packet has transport data smaller than RTASE_MIN_PAD_LEN,
the hardware parser expects additional packet data and may trigger a
TX hang.
To avoid these hardware issues, the driver applies the following
workarounds.
Drop malformed packets that may trigger this hardware issue before
transmission.
For IPv4 non-initial fragments, the hardware does not check the
fragment offset before parsing the expected transport header location.
As a result, these packets are still subject to transport header
parsing even though they do not contain a transport header. If the
transport data is shorter than the minimum transport header required
by the hardware parser, pad the transport data to the minimum
transport header length required by the hardware parser. Packets that
also match the hardware PTP parsing conditions continue to follow the
corresponding workaround.
For IPv6 fragmented packets, neither of the above hardware issues
occurs because the hardware only continues packet parsing when the
IPv6 Base Header Next Header field directly indicates UDP. Packets
carrying a Fragment Header do not continue through the subsequent
packet parsing stages.
For packets identified for hardware PTP parsing, pad the transport
data so it reaches RTASE_MIN_PAD_LEN before transmission.
Fixes: d6e882b89f ("rtase: Implement .ndo_start_xmit function")
Cc: stable@vger.kernel.org
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260709103456.83789-1-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mptcp_get_options() clears only the status group of struct
mptcp_options_received; data_seq, subflow_seq and data_len are filled in
by mptcp_parse_option() exclusively inside the DSS mapping block, which
runs only when the DSS M (mapping present) bit is set.
A peer can send a DSS option with the DATA_FIN flag set but the mapping
bit clear. The parser then records mp_opt->data_fin while leaving
data_len and data_seq uninitialized. For a zero-length segment
mptcp_incoming_options() evaluates
if (mp_opt.data_fin && mp_opt.data_len == 1 &&
mptcp_update_rcv_data_fin(msk, mp_opt.data_seq, mp_opt.dsn64))
which reads the uninitialized data_len and data_seq; KMSAN reports an
uninit-value in mptcp_incoming_options(). The stale data_seq can also be
fed into the receive-side DATA_FIN sequence tracking.
Record the DATA_FIN flag only when the DSS option carries a mapping, so
data_fin is never set without data_seq and data_len also being present.
data_fin is part of the status group that mptcp_get_options() clears up
front, so on the no-map path it stays zero and the zero-length DATA_FIN
branch is simply skipped. A DATA_FIN is always transmitted together with
a mapping (mptcp_write_data_fin() sets use_map along with data_seq and
data_len), so legitimate DATA_FIN handling is unaffected.
Move the pr_debug() that logs the parsed DSS flags below the mapping
block, so it reports the final data_fin value instead of the stale one
it would otherwise print before the assignment.
Fixes: 43b54c6ee3 ("mptcp: Use full MPTCP-level disconnect state machine")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260709191925.2811195-1-michael.bommarito@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure the IPv4/6 and UDP headers are writable before fixing them up in
geneve_post_decap_hint. As skb_ensure_writable can reallocate the skb linear
area, reload the GRO hint header pointer and only set the IPv4/6 header ones
after the call.
Fixes: fd0dd79657 ("geneve: use GRO hint option in the RX path")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/patchset/20260529144713.780938-1-atenart%40kernel.org
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260709125000.141092-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit d87773de9e ("clocksource/drivers/arm_arch_timer: Default to EL2
virtual timer when running VHE") causes boot to hang on Raspberry Pi 5.
The newly-selected EL2 virtual timer does not generate any interrupts,
even though the GIC_DIST_ENABLE_SET flag has been confirmed set via
readback.
It is highly unusual that this timer interrupt is non-operational because
this is a standard GIC interrupt corresponding to a standard Cortex-A76
CPU timer. However, Broadcom have confirmed for this SoC:
> the interrupt line was never connected in the first place as this was
> not identified as being a requirement
Remove the corresponding DeviceTree entry.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/all/ea15cce1-b393-43f6-8d58-3d6f90f0c0cd@samsung.com/
Fixes: faa3381267 ("arm64: dts: broadcom: Add minimal support for Raspberry Pi 5")
Signed-off-by: Daniel Drake <dan@reactivated.net>
Link: https://lore.kernel.org/r/20260716-bcm2712-el2-v2-1-e708f7fb42fa@reactivated.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
The BCM43752 is not reliable with the default 512-byte SDIO function 2
block size: on an i.MX8MP board with an AMPAK AP6275S module at
SDR104 / 200 MHz, an iperf TX stress test kills WLAN within seconds:
mmc_submit_one: CMD53 sg block write failed -84
brcmf_sdio_dpc: failed backplane access over SDIO, halting operation
Commit d2587c57ff ("brcmfmac: add 43752 SDIO ids and initialization")
set up the 43752 like the 4373 for the F2 watermark but missed the F2
block size, which the 4373 limits to 256 bytes. The vendor driver
(bcmdhd) also programs a 256-byte F2 block size for this chip and runs
the same hardware without errors.
Group the 43752 with the 4373, matching the F2 watermark handling.
With this change a 10-minute bidirectional iperf3 soak completes with
zero SDIO errors at ~270 Mbit/s in each direction.
Backporting note: kernels before v6.18 name this id
SDIO_DEVICE_ID_BROADCOM_CYPRESS_43752, so on those trees the case
label added by this patch must be adjusted to that name. Cherry-picking
the rename commit 74e2ef72bd ("wifi: brcmfmac: fix 43752 SDIO FWVID
incorrectly labelled as Cypress (CYW)") first is not a clean
alternative: on trees before v6.17 its context collides with the 43751
additions, and trees before v6.2 lack the FWVID framework it touches.
Fixes: d2587c57ff ("brcmfmac: add 43752 SDIO ids and initialization")
Cc: stable@vger.kernel.org # see patch description, needs adjustments for <= 6.17
Signed-off-by: LiangCheng Wang <zaq14760@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20260715-b43752-f2-blksz-v2-1-f9be49856050@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sk_clone() fails, sk_destruct() is called for the new socket.
If the parent socket has SK_FLAGS_TIMESTAMP in sk->sk_flags,
net_disable_timestamp() is called for the child socket even though
net_enable_timestamp() is not called for it.
Let's call net_enable_timestamp() before any failure path in
sk_clone().
Fixes: 704da560c0 ("tcp: update the netstamp_needed counter when cloning sockets")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/all/20260709032007.9E4D61F000E9@smtp.kernel.org/
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260709183315.965751-3-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When sk_clone() fails, sk_destruct() is called for the new socket.
If the parent socket has sk->sk_reuseport_cb, the child will call
reuseport_detach_sock() for the reuseport group.
Let's clear sk->sk_reuseport_cb before any failure path in sk_clone().
Note that this was not a problem before the cited commit because
reuseport_detach_sock() did nothing if the socket was not found in
the reuseport array.
Fixes: 5dc4c4b7d4 ("bpf: Introduce BPF_MAP_TYPE_REUSEPORT_SOCKARRAY")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/all/20260709032007.9E4D61F000E9@smtp.kernel.org/
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260709183315.965751-2-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MAC_AUTO_SW (VR_MII_DIG_CTRL1 bit 9) enables automatic XPCS speed
mode switching after CL37 auto-negotiation and is only meaningful in
SGMII MAC mode. The original code unconditionally set this bit on
every call to xgbe_an37_set(), including when called from
xgbe_an37_disable() with enable=false. This left MAC_AUTO_SW=1 after
AN was disabled, causing the XPCS to autonomously switch speed from
stale AN state during subsequent mode changes, breaking SGMII speed
negotiation on 1G copper SFP modules.
Patrick: This was breaking negotiation for all 1G SFP modules,
not just copper modules.
Fixes: 42fd432fe6 ("amd-xgbe: align CL37 AN sequence as per databook")
Reported-by: Patrick Oppenlander <patrick.oppenlander@gmail.com>
Link: https://lore.kernel.org/netdev/CAEg67GmFS0Q4oSZkz8zWdOzckSth9_vBPiOy6a7-d697C2w2Xg@mail.gmail.com
Signed-off-by: Prashanth Kumar KR <PrashanthKumar.K.R@amd.com>
Tested-by: Patrick Oppenlander <patrick.oppenlander@gmail.com>
Link: https://patch.msgid.link/20260709095006.3683940-1-prashanthkumar.k.r@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This field comes from userspace and should be validated against specific
limits depending on which Shader Model (SM) is available.
Fixes: 504901dbb0 ("drm/vmwgfx: Refactor surface_define to use vmw_surface_metadata")
Reported-by: Zero Day Initiative <zdi-disclosures@trendmicro.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ian Forbes <ian.forbes@broadcom.com>
Reviewed-by: Maaz Mombasawala <maaz.mombasawala@broadcom.com>
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://patch.msgid.link/20260623193314.506257-1-ian.forbes@broadcom.com
Commit 0ab03f353d ("net-gro: Fix GRO flush when receiving a GSO
packet.") added a flush check to skb_gro_receive(), but
skb_gro_receive_list() lacks the same validation.
As a result, packets marked with NAPI_GRO_CB(skb)->flush may still be
re-aggregated.
This allows already-GRO'd packets with existing frag_list to be
re-aggregated into a new GRO session, corrupting the frag_list chain
structure. When skb_segment() attempts to unpack these malformed packets,
it encounters invalid state and triggers a kernel panic.
Scenario (Tethering/Device forwarding):
1. Driver: Generated aggregated packet P1 via LRO with frag_list
2. Dev A: Receives aggregated fraglist packet and flush flag set
3. Dev A: Re-enters GRO, skb_gro_receive_list() is called
4. Missing flush check allows re-aggregation despite flush flag
5. Frag_list chain becomes corrupted (loops or dangling refs)
6. Dev B: TX path calls skb_segment(), crashes on corrupted frag_list
Root cause in skb_segment():
The check at line ~4891:
if (hsize <= 0 && i >= nfrags && skb_headlen(list_skb) &&
(skb_headlen(list_skb) == len || sg)) {
When frag_list is corrupted by double aggregation, when list_skb is
a NULL pointer from skb->next, skb_headlen(list_skb) dereference
NULL/corrupted pointers occurs.
Call Trace:
skb_headlen(NULL skb)
skb_segment
tcp_gso_segment
tcp4_gso_segment
inet_gso_segment
skb_mac_gso_segment
__skb_gso_segment
skb_gso_segment
validate_xmit_skb
validate_xmit_skb_list
sch_direct_xmit
qdisc_restart
__qdisc_run
qdisc_run
net_tx_action
Fix: Add NAPI_GRO_CB(skb)->flush validation to the early-return check in
skb_gro_receive_list(), matching the defensive programming pattern of
skb_gro_receive().
Fixes: 3a1296a38d ("net: Support GRO/GSO fraglist chaining.")
Cc: stable@vger.kernel.org
Signed-off-by: Shiming Cheng <shiming.cheng@mediatek.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260709014704.3625-1-shiming.cheng@mediatek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Avoid redundant allocations when allocating IMSIC page tables
- Apply SBI FWFT LOCK flag only on successful set
- Bound SBI PMU counter mask scan to BITS_PER_LONG, since on RV32
the PMU SBI start/stop helper can only access 32 PMU counters.
- Skip TLB flush when G-stage PTE becomes valid if the Svvptc
extension is available.
- Always show Zicbo[m|z|p] block sizes in ONE_REG
- Inject instruction access fault on unmapped guest fetch
- Use raw spinlock for irqs_pending and irqs_pending_mask
- Fix Spectre-v1 in vector register access via ONE_REG
x86:
- Fixes to SEV selftests.
- Once free_nested() did a VMCLEAR of shadow VMCS, there's no need to VMCLEAR it
again if the kernel is preempted and thread migration happens
- Preserve nested TDP shadow page tables if they are used as roots, instead of
clearing them unnecessarily
- Fix use of stale data if out-of-memory happens after vendor module reload
- Check for invalid/obsolete root *after* making MMU pages available, because
the latter can make a page invalid
- Only reset TSC Deadline Timer in apic_timer_expired on KVM_RUN
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmpfSUwUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOrWQf/S8Za6t7bZbQbJHDV0NXCKufpyKyz
l6WMsLGdn4LFLNqCtKhvQf5lEZ5PKRHFTGoWrO1wQSbREHRUCnfMD5lsSKQA4Grf
0QpQ6YBjXFv6zg0M456/Q/S1oyusyqkXXBS8BxlBQyfqR+ByKx8f4PXTGazfUua3
4SPHr5TUxr6CXy8715OQUGa1Xdf0/5d3OseiAgBwqM31yZPhK0tsar77Cd9P93bs
DC+FzfphHg0gb3s/xSfuVR0BPnqHvQMDF9rS/YKgJgJdZkzHXCo7muWRQmHWK+FR
Q2zOTWSlJATQucC0+2j1yj2Wdhg1itgZTfj/8RaIDRKbmjk0S1bLc3bamg==
=Svds
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"RISC-V:
- Avoid redundant allocations when allocating IMSIC page tables
- Apply SBI FWFT LOCK flag only on successful set
- Bound SBI PMU counter mask scan to BITS_PER_LONG, since on RV32 the
PMU SBI start/stop helper can only access 32 PMU counters.
- Skip TLB flush when G-stage PTE becomes valid if the Svvptc
extension is available.
- Always show Zicbo[m|z|p] block sizes in ONE_REG
- Inject instruction access fault on unmapped guest fetch
- Use raw spinlock for irqs_pending and irqs_pending_mask
- Fix Spectre-v1 in vector register access via ONE_REG
x86:
- Fixes to SEV selftests
- Once free_nested() did a VMCLEAR of shadow VMCS, there's no need to
VMCLEAR it again if the kernel is preempted and thread migration
happens
- Preserve nested TDP shadow page tables if they are used as roots,
instead of clearing them unnecessarily
- Fix use of stale data if out-of-memory happens after vendor module
reload
- Check for invalid/obsolete root *after* making MMU pages available,
because the latter can make a page invalid
- Only reset TSC Deadline Timer in apic_timer_expired on KVM_RUN"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Only reset TSC Deadline Timer in apic_timer_expired on KVM_RUN
KVM: selftests: sev_init2_tests: Derive SEV availability from KVM
KVM: selftests: sev_smoke_test: Only run VM types the host offers
KVM: x86/mmu: Fix use-after-free on vendor module reload
KVM: x86/mmu: Preserve nested TDP shadow page tables if they are used as roots
KVM: x86: Check for invalid/obsolete root *after* making MMU pages available
KVM: nVMX: Hide shadow VMCS right after VMCLEAR
KVM: riscv: Fix Spectre-v1 in vector register access
RISC-V: KVM: Serialize virtual interrupt pending state updates
RISC-V: KVM: Inject instruction access fault on unmapped guest fetch
RISC-V: KVM: Zicbo[m|z|p] block sizes should be always present in ONE_REG
riscv: kvm: Skip TLB flush when G-stage PTE becomes valid with Svvptc
KVM: riscv: PMU: Bound counter mask scan to BITS_PER_LONG
KVM: riscv: SBI FWFT: Apply LOCK flag only on successful set
RISC-V: KVM: Avoid redundant page-table allocations in ioremap topup
prevent_memory_remove_notifier() advances pfn while scanning the requested
range for early memory. When the loop completes, pfn is at or beyond
end_pfn. Passing it to can_unmap_without_split() therefore checks a range
after the one being offlined.
Consequently, a valid request can be rejected based on the following
range, while a request that would split a leaf mapping can be accepted if
the shifted range can be unmapped without a split. This was observed with
CXL DAX memory, where the final memory block was incorrectly allowed to
be offlined.
Pass arg->start_pfn into can_unmap_without_split() so it checks the
requested range.
Fixes: 95a58852b0 ("arm64/mm: Reject memory removal that splits a kernel leaf mapping")
Signed-off-by: Richard Cheng <icheng@nvidia.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
- tracing/probes: Avoid temporary buffer truncation in match_command_args()
Compare argument name, delimiter, and comm expression directly instead of
formatting into a stack buffer to prevent false matching failures.
- tracing/probes: Prevent out-of-bounds write in __trace_probe_log_err()
Return early when trace_probe_log.argc is zero to prevent out-of-bounds
access when constructing the formatted error command string.
- tracing/probes: Fix potential underflow in LEN_OR_ZERO macro
Ensure buffer length is greater than current position before subtraction
to prevent unsigned size underflow when formatting print strings.
- tracing/eprobe: Fix exact system name matching in eprobe_dyn_event_match()
Check system name null-termination to avoid partial prefix matching when
comparing event probe target system names.
-----BEGIN PGP SIGNATURE-----
iQFPBAABCgA5FiEEh7BulGwFlgAOi5DV2/sHvwUrPxsFAmpfMPgbHG1hc2FtaS5o
aXJhbWF0c3VAZ21haWwuY29tAAoJENv7B78FKz8bDm8IAJ3GuBwQOTcVyn1+7Poh
fOtXOD9yMIV2YYoe6MDD/ZF1JCCnJgzgjPOqRbZjM4uGE8QbEuGnrwwu3zRiNON3
JU1R5aOxadflNhOnY7HxPjDHTwxJ5z+Ju10wPM+YE3M9gLKia8uzCabdEgYEly01
Rx6kpGKdsNgtJ/uAbrZlx++YtJCmBI1j+SdnRgNSejbcJUBtTmt+VYA+oh7ISF0f
Fuhw6MuznpnA9JkLrPJaUI6KLiNLEoLQVS2gqhCD0PvrlDGF/h+b7Qbv9ML0C8YW
W0p38Sq0Pc9lNlukYJlkh1A4H7lbAGpdGgZVoCvMQZt1ccy+H1QYfXzrFRlYyRWk
n6g=
=pC9O
-----END PGP SIGNATURE-----
Merge tag 'probes-fixes-v7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull probes fixes from Masami Hiramatsu:
- Avoid temporary buffer truncation in match_command_args()
Compare argument name, delimiter, and comm expression directly
instead of formatting into a stack buffer to prevent false
matching failures
- Prevent out-of-bounds write in __trace_probe_log_err()
Return early when trace_probe_log.argc is zero to prevent
out-of-bounds access when constructing the formatted error
command string
- Fix potential underflow in LEN_OR_ZERO macro
Ensure buffer length is greater than current position before
subtraction to prevent unsigned size underflow when formatting
print strings
- Fix exact system name matching in eprobe_dyn_event_match()
Check system name null-termination to avoid partial prefix
matching when comparing event probe target system names
* tag 'probes-fixes-v7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/eprobe: Fix exact system name matching in eprobe_dyn_event_match()
tracing/probes: Fix potential underflow in LEN_OR_ZERO macro
tracing/probes: Prevent out-of-bounds write in __trace_probe_log_err()
tracing/probes: Avoid temporary buffer truncation in trace_probe_match_command_args()
Address size fault, level -1 is encoded as 0b101001 or 0x29 according to
the Arm ARM. Correct the value to match the spec. This also matches the
offset of "level -1 address size fault" in the fault_info array in
fault.c.
Fixes: fb8a3eba9c ("KVM: arm64: Only read HPFAR_EL2 when value is architecturally valid")
Signed-off-by: Steven Price <steven.price@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
-----BEGIN PGP SIGNATURE-----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=1jNx
-----END PGP SIGNATURE-----
Merge tag 'for-7.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"I'm catching up with the fix backlog in the development branch, so
here's a number of them and will probably send one more for this or
the next rc:
- relocation fixes:
- skip attempting compression on reloc inodes
- exclude inline extents from file extent offset checks
- fix minor memory leak after error when adding reloc root
- fix root cleanup after inserting and merging
- fix clearing folio tags after writeback
- clear logging flag of extent map before splitting
- fix unsigned 32/64 type conversions when accounting dirty metadata,
leading to continually exceeding threshold
- fix regression in 32bit compat ioctl for subvolume info
- fix type of SEARCH_TREE ioctl buffer in UAPI header
- fix expression in ASSERT expression which can be unconditionally
evaluated on some compilers
- only account delalloc bytes for regular inodes"
* tag 'for-7.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix GET_SUBVOL_INFO after compat refactor
btrfs: free mapping node on duplicate reloc root insert
btrfs: fix a regression where PAGECACHE_TAG_DIRTY is never cleared
btrfs: don't propagate EXTENT_FLAG_LOGGING to split extent maps
btrfs: fix u32 to s64 type conversion in dirty_metadata_bytes accounting
btrfs: fix NULL pointer deref during assertion in btrfs_backref_free_node()
btrfs: only account delalloc bytes for regular file inodes in btrfs_getattr()
btrfs: reject inline file extents item in get_new_location()
btrfs: do not try compression for data reloc inodes
btrfs: declare btrfs_ioctl_search_args_v2::buf as __u8
btrfs: fix reloc root cleanup in merge_reloc_roots()
btrfs: fix use-after-free on reloc root after error in insert_dirty_subvol()
The MSI Crosshair A16 HX D7WFKG has an internal digital microphone
connected through AMD ACP6x, but the system does not expose the
AcpDmicConnected ACPI property. As a result, acp_yc_mach does not bind
and no DMIC capture device is created.
Add a DMI quirk for this model. This was tested on a system with board
MS-15PL, BIOS E15PLAMS.10B, and AMD ACP6x rev 0x62. After applying the
quirk, the internal microphone appears as an acp6x DMIC capture device
and records correctly.
Signed-off-by: 郑鸿源 <spark_psc@outlook.com>
Reviewed-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://patch.msgid.link/20260721-master-v1-1-6f56d5a54d96@outlook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A bug was reported when rtla-timerlat-top tool performs on-threshold
actions, even though no threshold was hit. This is reproduced even if no
threshold is set at all:
$ rtla timerlat top -q -c 0 --on-threshold shell,command='echo BAD'
BAD
Timer Latency
...
The bug is due to incorrect logic in timerlat_top_bpf_main_loop().
The loop uses timerlat_bpf_wait(), the return values of which are:
- > 0 (number of ringbuffer entries): at least 1 CPU hit threshold
- = 0: time out
- < 0: wait was interrupted by a signal
Commit 3138df6f0c ("rtla/timerlat: Exit top main loop on any non-zero
wait_retval") changed the condition for "threshold hit" from
"wait_reval == 1" (exactly 1 CPU hit threshold) to "wait_retval != 0",
to fix a race where multiple CPUs hit the threshold at the same time.
That also made it incorrectly include a signal (< 0), coming from either
duration expired (SIGALRM) or user interrupt (SIGINT).
Check for wait_retval greater than zero in the if condition to cover all
return values correctly.
Fixes: 3138df6f0c ("rtla/timerlat: Exit top main loop on any non-zero wait_retval")
Reported-by: Attila Fazekas <afazekas@redhat.com>
Reviewed-by: Wander Lairson Costa <wander@redhat.com>
Link: https://lore.kernel.org/r/20260713141047.687877-1-tglozar@redhat.com
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
The legacy firmware update path does not support per-component updates.
If a user specifies a component parameter with devlink flash, reject
the request with -EOPNOTSUPP rather than silently ignoring the component
parameter and flashing the entire firmware image.
Fixes: 49ce92fbee ("pds_core: add FW update feature to devlink")
Signed-off-by: Nikhil P. Rao <nikhil.rao@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260708163649.128620-1-nikhil.rao@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
vc4_gem_object_mmap() rejects a writable mapping of a validated shader
BO, but leaves VM_MAYWRITE set. Userspace can map the BO read-only and
then turn it writable with mprotect().
Validated shader BOs must stay read-only: the validator checks the
instructions once and the GPU trusts them afterwards. A writable
mapping lets userspace rewrite the code after validation, bypassing the
validator.
Clear VM_MAYWRITE on the read-only path so the mapping cannot be
upgraded, as i915 already does for its read-only objects.
Fixes: 463873d570 ("drm/vc4: Add an API for creating GPU shaders in GEM BOs.")
Cc: stable@vger.kernel.org
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/dri-devel/20260720085554.B0AF01F000E9@smtp.kernel.org/
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Link: https://patch.msgid.link/20260721011558.1672477-1-lilinmao@kylinos.cn
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
pmsr_parse_ftm() rejects a request that omits NOMINAL_TIME only for
non-trigger-based PD ranging. It then reads the attribute
unconditionally for every non-trigger-based request:
out->ftm.nominal_time =
nla_get_u32(tb[NL80211_PMSR_FTM_REQ_ATTR_NOMINAL_TIME]);
For the other non-trigger-based request types NOMINAL_TIME is optional,
so tb[...] can be NULL and nla_get_u32() dereferences a NULL pointer.
Keep the requirement for PD ranging and read the nominal-time value only
when the attribute is present.
Fixes: 8823a9b0e7 ("wifi: cfg80211: add NTB continuous ranging and FTM request type support")
Cc: stable@vger.kernel.org
Assisted-by: Codex:gpt-5
Assisted-by: Claude:opus-4.8
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260708195911.84365-5-enderaoelyther@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This PR contains quite a few fixes, mostly found by LLMs. Notably:
- missing validation of TLVs length
- missing validation on the revision of BIOS tables
- missing validation of fw responses length
- protect against double free of RX pointers
- avoid double deregistration of the tzone core
- validate fields in FW responses before using them
- fix off-by-one in WLAN_EID_EXT_CAPABILITY parsing
- Add missing support for UNII-9
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQM3A3Pv7vbm9vtjWbacY7uyt+OfQUCal9OxwAKCRDacY7uyt+O
fWfkAQDb/MrxlM6sihTSHBQ+lrLPgp0JYTkSHYGI606/CFO4swD+PLcMPeDvUm1+
fIP1NybrXA3jVfmt4EEm6VVF1LL8bwI=
=wkfs
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-fixes-2026-07-21' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Miri Korenblit says:
====================
wifi: iwlwif: fixes - 2026-07-21
This PR contains quite a few fixes, mostly found by LLMs. Notably:
- missing validation of TLVs length
- missing validation on the revision of BIOS tables
- missing validation of fw responses length
- protect against double free of RX pointers
- avoid double deregistration of the tzone core
- validate fields in FW responses before using them
- fix off-by-one in WLAN_EID_EXT_CAPABILITY parsing
- Add missing support for UNII-9
====================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
hwsim_tx_info_frame_received_nl() casts the HWSIM_ATTR_TX_INFO payload
to a struct hwsim_tx_rate * and unconditionally reads
IEEE80211_TX_MAX_RATES entries (8 bytes) from it. The policy only bounds
the attribute from above (NLA_BINARY .len is a maximum) and the op sets
GENL_DONT_VALIDATE_STRICT, so a short or zero-length attribute is
accepted and the loop reads past the payload.
Require the exact length in the policy, so a malformed attribute is
rejected before the handler runs.
Signed-off-by: Ibrahim Hashimov <security@auditcode.ai>
Assisted-by: AuditCode-AI:2026.07
Link: https://patch.msgid.link/20260721115346.17236-1-security@auditcode.ai
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
brcmf_fw_crashed() and the debugfs "reset" entry both schedule
drvr->bus_reset, whose callback recovers drvr through container_of()
and dereferences it. The removal path frees drvr (brcmf_free ->
wiphy_free) without draining the work, so a bus_reset callback pending
or running during removal can outlive drvr.
Cancellation cannot live in brcmf_detach() or brcmf_free(): the work
callback reaches teardown through the bus .reset op (PCIe
brcmf_pcie_reset -> brcmf_detach; SDIO brcmf_sdio_bus_reset ->
brcmf_sdiod_remove -> brcmf_free), so cancelling there would wait for
the running work and deadlock.
Add a per-bus mutex (bus_reset_lock) and route all arming through
brcmf_bus_schedule_reset(), which under the lock skips when the bus is
marked removing. Each bus remove entry calls
brcmf_bus_cancel_reset_work(), which under the same lock sets removing
and cancels the work. Holding the mutex across cancel_work_sync() makes
the set-removing + drain step atomic. Every producer reaches the arming
path from process context -- the PCIe firmware-halt notification runs in
the threaded IRQ handler (brcmf_pcie_isr_thread) and the SDIO hostmail
path runs from the data workqueue -- so the mutex is taken only in
sleepable contexts. Where applicable the remove entry first stops the
firmware-crash producer: on PCIe mask the mailbox and synchronize_irq;
on SDIO unregister the bus interrupt and cancel the data worker, which
also reports firmware halts through brcmf_fw_crashed(). The mutex is
initialized at bus allocation. The SDIO suspend power-off path frees
drvr through the same brcmf_sdiod_remove() and takes the same lock;
resume re-allows the work only on a successful re-probe.
Also guard brcmf_fw_crashed() against a NULL bus_if/drvr: it can fire
before brcmf_attach() wires up drvr, and it dereferences drvr
(bphy_err/brcmf_dev_coredump) before reaching the arming gate.
The bus_reset work is shared across buses, so the drain is applied to
every remove path: PCIe (the .reset op introduced by the Fixes commit),
SDIO (arms the same work through brcmf_fw_crashed()), and USB (via the
debugfs "reset" entry). cancel_work_sync() drains a running or pending
bus_reset work item before removal frees drvr, and patch 1/2 makes the
scratch-buffer release safe when reset teardown has already released
those DMA buffers.
This patch fixes the lifetime of the bus_reset work item itself. It does
not attempt to address the separate, pre-existing lifetime of the
asynchronous firmware completion started by the PCIe reset path. That
callback needs its own lifetime/ownership protocol and is being tracked
separately.
This issue was found by an in-house static analysis tool.
Fixes: 4684997d9e ("brcmfmac: reset PCIe bus on a firmware crash")
Cc: stable@vger.kernel.org
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Assisted-by: Codex:gpt-5.6
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20260718024353.3147201-3-fanwu01@zju.edu.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
brcmf_pcie_release_scratchbuffers() frees the shared.scratch and
shared.ringupd DMA buffers with dma_free_coherent() but does not clear
the pointers afterwards, unlike the sibling release_ringbuffers() which
NULLs commonrings/flowrings/idxbuf on release.
Both the bus_reset .reset callback (brcmf_pcie_reset) and
brcmf_pcie_remove() call release_scratchbuffers. When reset teardown
has run before removal, remove's own teardown would call
dma_free_coherent() a second time on the already-freed DMA allocation.
NULL the pointers after free, matching release_ringbuffers(), so a later
release observes that the allocation has already been released. This
patch makes repeated sequential release safe; the reset-work lifetime is
handled separately by the following patch.
This issue was found by an in-house static analysis tool.
Fixes: 4684997d9e ("brcmfmac: reset PCIe bus on a firmware crash")
Cc: stable@vger.kernel.org
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Assisted-by: Codex:gpt-5.6
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://patch.msgid.link/20260718024353.3147201-2-fanwu01@zju.edu.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an AP buffers frames for a station on its per-station TXQs and the
station subsequently enters power save, sta_ps_start() records the
buffered TIDs in txq_buffered_tids but does not update the TIM. The
station's TIM bit is only ever set when a further frame is buffered
while the station is already asleep
(ieee80211_tx_h_unicast_ps_buf() -> sta_info_recalc_tim()).
If no further downlink frame arrives for that station the beacon
TIM never advertises the buffered traffic. A station relying on the
TIM then remains in doze indefinitely on top of a non-empty queue. Its
TXQs were removed from the scheduler's active list at PS entry, nothing
pages it, and the flow deadlocks until an unrelated event wakes the
station.
Recalculate the TIM at the end of sta_ps_start(), so traffic
already buffered at PS entry is advertised immediately.
sta_info_recalc_tim() already consults txq_buffered_tids, which is
updated above, and is safe in this context (it is already called
from equivalent paths such as the tx handlers and
ieee80211_handle_filtered_frame()).
Fixes: ba8c3d6f16 ("mac80211: add an intermediate software queue implementation")
Signed-off-by: Andrew Pope <andrew.pope@morsemicro.com>
Link: https://patch.msgid.link/20260717011751.79524-1-andrew.pope@morsemicro.com
[add wifi: subject prefix]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
dmar_latency_disable() intends to zero out only the single
latency_statistic entry for the given type, but the memset size was
computed as sizeof(*lstat) * DMAR_LATENCY_NUM, which clears the entire
array starting from &lstat[type].
When type > 0, this writes beyond the end of the allocated array,
corrupting adjacent memory.
Fix by using sizeof(*lstat) to clear only the target entry.
Fixes: 55ee5e67a5 ("iommu/vt-d: Add common code for dmar latency performance monitors")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Will Deacon <will@kernel.org>
The ivrs_acpihid command-line parser appends entries to a fixed
four-element early_acpihid_map array. Unlike the sibling IOAPIC and HPET
parsers, it does not reject a fifth entry before incrementing the map size.
Check the capacity at the common found label before parsing the HID and
UID or writing the entry.
Fixes: ca3bf5d47c ("iommu/amd: Introduces ivrs_acpihid kernel parameter")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Reviewed-by: Ankit Soni <Ankit.Soni@amd.com>
Signed-off-by: Will Deacon <will@kernel.org>
mwifiex_tdls_add_ht_oper() gates its follow-the-AP-bandwidth path on
bss_desc->bcn_ht_cap being present, but then dereferences a different
pointer, bss_desc->bcn_ht_oper:
if (ISSUPP_CHANWIDTH40(priv->adapter->hw_dot_11n_dev_cap) &&
bss_desc->bcn_ht_cap &&
ISALLOWED_CHANWIDTH40(bss_desc->bcn_ht_oper->ht_param))
bcn_ht_cap and bcn_ht_oper are populated independently while parsing the
associated AP's beacon in mwifiex_update_bss_desc_with_ie(): an AP that
advertises an HT Capabilities element but no HT Operation element leaves
bcn_ht_cap non-NULL and bcn_ht_oper NULL. Setting up a TDLS link to a
peer while associated to such an AP then dereferences the NULL
bcn_ht_oper and crashes the kernel. Every other bcn_ht_oper user in the
driver NULL-checks it first.
Guard on the pointer that is actually dereferenced.
Found by 0sec automated security-research tooling (https://0sec.ai).
Fixes: 396939f940 ("mwifiex: add HT operation IE in TDLS setup confirm")
Cc: stable@vger.kernel.org
Assisted-by: 0sec:multi-model
Signed-off-by: Doruk Tan Ozturk <doruk@0sec.ai>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20260716103042.88469-1-doruk@0sec.ai
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace deprecated one-element arrays with flexible array members.
CONFIG_FORTIFY_SOURCE reports the following warning when
one-element arrays are used as variable-length buffers:
sta_cmd.c:1033 mwifiex_sta_prepare_cmd
memcpy: detected field-spanning write (size 84) of single field
"domain->triplet" at .../marvell/mwifiex/sta_cmd.c:1033 (size 3)
Convert affected structs to use flexible array members.
- Preserve existing wire layouts.
- Use DECLARE_FLEX_ARRAY() for structs inside affected unions.
Tested-on: WRT3200ACM, OpenWrt
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20260716001728.57799-1-gvalkov@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
at76_guess_freq() checks only that the received frame is at least a bare
802.11 header (24 bytes) before subtracting the fixed management-body
offset:
len -= el_off;
For both beacon and probe response frames, el_off is 36. If the frame is
shorter than el_off, subtracting it causes the calculated IE length to
wrap. The length is eventually passed to cfg80211_find_elem_match() as a
very large unsigned value, so the element walk runs beyond the RX skb.
This path is reached from at76_rx_tasklet() while scanning. If the device
delivers a truncated beacon or probe response, the oversized IE length
causes an out-of-bounds read during scanning.
Skip the IE lookup if the frame does not reach the variable elements,
before subtracting el_off.
Fixes: 1264b95146 ("at76c50x-usb: add driver")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Huihui Huang <hhhuang@smu.edu.sg>
Link: https://patch.msgid.link/20260715140815.1242033-1-hhhuang@smu.edu.sg
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Hardware implementations report Scalable-Mode Page-walk Coherency Support
via the SMPWCS field in the extended capability register. If the hardware
does not support page-walk coherency, a clflush is required every time
the page table entries (which are walked by the IOMMU hardware) are
updated.
In the SVA case, page tables are managed by the CPU mm core, not by the
IOMMU driver. Because the IOMMU driver has no way of knowing whether the
CPU page table management code has ensured coherency via clflush, the
driver must deny SVA if the hardware does not support coherent paging.
Fixes: ff3dc6521f ("iommu/vt-d: Fix CPU and IOMMU SVM feature matching checks")
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Samiullah Khawaja <skhawaja@google.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Will Deacon <will@kernel.org>
mwifiex_process_uap_event() handles EVENT_UAP_STA_ASSOC by exposing the
(re)association request IEs that the firmware copies into the event:
sinfo->assoc_req_ies = &event->data[len];
len = (u8 *)sinfo->assoc_req_ies - (u8 *)&event->frame_control;
sinfo->assoc_req_ies_len = le16_to_cpu(event->len) - (u16)len;
event->len is supplied by the device firmware and is never validated,
and the subtraction is unchecked. assoc_req_ies points into
adapter->event_body[MAX_EVENT_SIZE], a fixed-size array embedded in the
kmalloc()'d struct mwifiex_adapter.
On the ap_11n_enabled path mwifiex_set_sta_ht_cap() walks these IEs with
cfg80211_find_ie(), whose for_each_element() loop dereferences each
element header. A firmware-reported event->len larger than the bytes
actually received makes assoc_req_ies_len describe IEs that extend past
event_body, so the walk reads out of the adapter slab object, a
slab-out-of-bounds read (KASAN: slab-out-of-bounds in cfg80211_find_ie).
An event->len smaller than the header instead makes the int subtraction
negative, which wraps to a huge size_t when stored in assoc_req_ies_len.
The same length is handed to cfg80211_new_sta(), so a more modest
over-claim can also copy stale event_body bytes into the
NL80211_CMD_NEW_STATION notification.
A malicious or malfunctioning mwifiex device (USB/SDIO/PCIe) can deliver
such an event while the interface is in AP/uAP mode.
Validate event->len before use: reject a length that underflows the
header or that would place the IEs outside the event_body[] buffer the
event was copied into. event->len here is struct mwifiex_assoc_event.len,
a payload field internal to this event, not the transport frame length,
so it is validated in this handler rather than at the generic
MWIFIEX_TYPE_EVENT receive path, which only sees the event cause and the
transport frame length. The bound is against event_body[MAX_EVENT_SIZE]
rather than the actually-received length because the transports store the
event differently (USB and SDIO leave the 4-byte event header in
event_skb, PCIe strips it via skb_pull), whereas event_body is the single
fixed buffer all of them copy the event into. This is the event-path
analogue of the receive-path bounds checks added in commit 1195852816
("wifi: mwifiex: Fix OOB and integer underflow when rx packets").
Fixes: e568634ae7 ("mwifiex: add AP event handling framework")
Signed-off-by: HE WEI (ギカク) <skyexpoc@gmail.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20260715135711.34688-1-skyexpoc@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This information can be considered part of the capabilities and should
also be copied to the NAN data station.
Fixes: 27e9b326b6 ("wifi: mac80211: support NAN stations")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260714141038.15620aa5324b.I049254b854ac91c32e0768eb7c819f32eda34218@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
