Added the PERF_PMU_CAP_NO_INTERRUPT flag because the legacy pmu driver
does not provide sampling capabilities
Added the PERF_PMU_CAP_NO_EXCLUDE flag because the legacy pmu driver
does not provide the ability to disable counter incrementation in
different privilege modes
Suggested-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Vadim Shakirov <vadim.shakirov@syntacore.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Fixes: 9b3e150e31 ("RISC-V: Add a simple platform driver for RISC-V legacy perf")
Link: https://lore.kernel.org/r/20240227170002.188671-2-vadim.shakirov@syntacore.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Currently, GPU resets can now be performed successfully on the Raven
series. While GPU reset is required for the S3 suspend abort case.
So now can enable gpu reset for S3 abort cases on the Raven series.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's unreasonable to use 0 as the power1_min_cap when
OD is disabled. So, use the same lower limit as the value
used when OD is enabled.
Fixes: 1958946858 ("drm/amd/pm: Support for getting power1_cap_min value")
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Adds a check in the map_hw_resources function to prevent a potential
buffer overflow. The function was accessing arrays using an index that
could potentially be greater than the size of the arrays, leading to a
buffer overflow.
Adds a check to ensure that the index is within the bounds of the
arrays. If the index is out of bounds, an error message is printed and
break it will continue execution with just ignoring extra data early to
prevent the buffer overflow.
Reported by smatch:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/dml2_wrapper.c:79 map_hw_resources() error: buffer overflow 'dml2->v20.scratch.dml_to_dc_pipe_mapping.disp_cfg_to_stream_id' 6 <= 7
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/dml2_wrapper.c:81 map_hw_resources() error: buffer overflow 'dml2->v20.scratch.dml_to_dc_pipe_mapping.disp_cfg_to_plane_id' 6 <= 7
Fixes: 7966f319c6 ("drm/amd/display: Introduce DML2")
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Suggested-by: Roman Li <roman.li@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
struct veth_rq is pretty large, 832B total without debug
options enabled. Since commit under Fixes we try to pre-allocate
enough queues for every possible CPU. Miao Wang reports that
this may lead to order-5 allocations which will fail in production.
Let the allocation fallback to vmalloc() and try harder.
These are the same flags we pass to netdev queue allocation.
Reported-and-tested-by: Miao Wang <shankerwangmiao@gmail.com>
Fixes: 9d3684c24a ("veth: create by default nr_possible_cpus queues")
Link: https://lore.kernel.org/all/5F52CAE2-2FB7-4712-95F1-3312FBBFA8DD@gmail.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240223235908.693010-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
One patch of a series of three that was sent fixing issues with the
ppc4xx driver was targeted at -next, unfortunately it being sandwiched
between two others that targeted mainline tripped up my workflow and
caused it to get merged along with the others. The ppc4xx driver is
only buildable in very limited configurations so none of the CI catches
issues with it.
Fixes: de4af897dd ("spi: ppc4xx: Fix fallout from rename in struct spi_bitbang")
Signed-off-by: Mark Brown <broonie@kernel.org>
When rebuilding the lif after an FLR, be sure to restore the
current netdev features, not do the usual first time feature
init. This prevents losing user changes to things like TSO
or vlan tagging states.
Fixes: 45b84188a0 ("ionic: keep filters across FLR")
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since we now have potential cases of NULL cmd_regs and info_regs
during a reset recovery, and left NULL if a reset recovery has
failed, we need to check that they exist before we use them.
Most of the cases were covered in the original patch where we
verify before doing the ioreadb() for health or cmd status.
However, we need to protect a few uses of io mem that could
be hit in error recovery or asynchronous threads calls as well
(e.g. ethtool or devlink handlers).
Fixes: 219e183272 ("ionic: no fw read when PCI reset failed")
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
AER recovery handler can trigger a PCI Reset after tearing
down the device setup in the error detection handler. The PCI
Reset handler will also attempt to tear down the device setup,
and this second tear down needs to know that it doesn't need
to call pci_release_regions() a second time. We can clear
num_bars on tear down and use that to decide later if we need
to clear the resources. This prevents a harmless but disturbing
warning message
resource: Trying to free nonexistent resource <0xXXXXXXXXXX-0xXXXXXXXXXX>
Fixes: c3a910e1c4 ("ionic: fill out pci error handlers")
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The following patch accidentally removed the code for delivering
completions for cancelled reads and writes to user space: "[PATCH 04/33]
aio: remove retry-based AIO"
(https://lore.kernel.org/all/1363883754-27966-5-git-send-email-koverstreet@google.com/)
>From that patch:
- if (kiocbIsCancelled(iocb)) {
- ret = -EINTR;
- aio_complete(iocb, ret, 0);
- /* must not access the iocb after this */
- goto out;
- }
This leads to a leak in user space of a struct iocb. Hence this patch
that restores the code that reports to user space that a read or write
has been cancelled successfully.
Fixes: 41003a7bcf ("aio: remove retry-based AIO")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Sandeep Dhavale <dhavale@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: stable@vger.kernel.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240215204739.2677806-3-bvanassche@acm.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
If a directory has a block with only ".__afsXXXX" files in it (from
uncompleted silly-rename), these .__afsXXXX files are skipped but without
advancing the file position in the dir_context. This leads to
afs_dir_iterate() repeating the block again and again.
Fix this by making the code that skips the .__afsXXXX file also manually
advance the file position.
The symptoms are a soft lookup:
watchdog: BUG: soft lockup - CPU#3 stuck for 52s! [check:5737]
...
RIP: 0010:afs_dir_iterate_block+0x39/0x1fd
...
? watchdog_timer_fn+0x1a6/0x213
...
? asm_sysvec_apic_timer_interrupt+0x16/0x20
? afs_dir_iterate_block+0x39/0x1fd
afs_dir_iterate+0x10a/0x148
afs_readdir+0x30/0x4a
iterate_dir+0x93/0xd3
__do_sys_getdents64+0x6b/0xd4
This is almost certainly the actual fix for:
https://bugzilla.kernel.org/show_bug.cgi?id=218496
Fixes: 57e9d49c54 ("afs: Hide silly-rename files from userspace")
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/786185.1708694102@warthog.procyon.org.uk
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Markus Suvanto <markus.suvanto@gmail.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
Currently intel_hdcp is not being extracted from primary connector
this patch fixes that.
Fixes: 524240b231 ("drm/i915/hdcp: Propagate aux info in DP HDCP functions")
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240226063051.1685326-3-suraj.kandpal@intel.com
(cherry picked from commit 909fff3e46)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
It had pop noise from Headphone port when system reboot state.
If NID 58h Index 0x0 to fill default value, it will reduce pop noise.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/7493e207919a4fb3a0599324fd010e3e@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
FSDAX and reflink can work together now, let's drop this warning.
Signed-off-by: Shiyang Ruan <ruansy.fnst@fujitsu.com>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
Matthieu Baerts says:
====================
mptcp: more misc. fixes for v6.8
This series includes 6 types of fixes:
- Patch 1 fixes v4 mapped in v6 addresses support for the userspace PM,
when asking to delete a subflow. It was done everywhere else, but not
there. Patch 2 validates the modification, thanks to a subtest in
mptcp_join.sh. These patches can be backported up to v5.19.
- Patch 3 is a small fix for a recent bug-fix patch, just to avoid
printing an irrelevant warning (pr_warn()) once. It can be backported
up to v5.6, alongside the bug-fix that has been introduced in the
v6.8-rc5.
- Patches 4 to 6 are fixes for bugs found by Paolo while working on
TCP_NOTSENT_LOWAT support for MPTCP. These fixes can improve the
performances in some cases. Patches can be backported up to v5.6,
v5.11 and v6.7 respectively.
- Patch 7 makes sure 'ss -M' is available when starting MPTCP Join
selftest as it is required for some subtests since v5.18.
- Patch 8 fixes a possible double-free on socket dismantle. The issue
always existed, but was unnoticed because it was not causing any
problem so far. This fix can be backported up to v5.6.
- Patch 9 is a fix for a very recent patch causing lockdep warnings in
subflow diag. The patch causing the regression -- which fixes another
issue present since v5.7 -- should be part of the future v6.8-rc6.
Patch 10 validates the modification, thanks to a new subtest in
diag.sh.
====================
Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-0-162e87e48497@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mptcp diag interface already experienced a few locking bugs
that lockdep and appropriate coverage have detected in advance.
Let's add a test-case triggering the relevant code path, to prevent
similar issues in the future.
Be careful to cope with very slow environments.
Note that we don't need an explicit timeout on the mptcp_connect
subprocess to cope with eventual bug/hang-up as the final cleanup
terminating the child processes will take care of that.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-10-162e87e48497@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
when MPTCP server accepts an incoming connection, it clones its listener
socket. However, the pointer to 'inet_opt' for the new socket has the same
value as the original one: as a consequence, on program exit it's possible
to observe the following splat:
BUG: KASAN: double-free in inet_sock_destruct+0x54f/0x8b0
Free of addr ffff888485950880 by task swapper/25/0
CPU: 25 PID: 0 Comm: swapper/25 Kdump: loaded Not tainted 6.8.0-rc1+ #609
Hardware name: Supermicro SYS-6027R-72RF/X9DRH-7TF/7F/iTF/iF, BIOS 3.0 07/26/2013
Call Trace:
<IRQ>
dump_stack_lvl+0x32/0x50
print_report+0xca/0x620
kasan_report_invalid_free+0x64/0x90
__kasan_slab_free+0x1aa/0x1f0
kfree+0xed/0x2e0
inet_sock_destruct+0x54f/0x8b0
__sk_destruct+0x48/0x5b0
rcu_do_batch+0x34e/0xd90
rcu_core+0x559/0xac0
__do_softirq+0x183/0x5a4
irq_exit_rcu+0x12d/0x170
sysvec_apic_timer_interrupt+0x6b/0x80
</IRQ>
<TASK>
asm_sysvec_apic_timer_interrupt+0x16/0x20
RIP: 0010:cpuidle_enter_state+0x175/0x300
Code: 30 00 0f 84 1f 01 00 00 83 e8 01 83 f8 ff 75 e5 48 83 c4 18 44 89 e8 5b 5d 41 5c 41 5d 41 5e 41 5f c3 cc cc cc cc fb 45 85 ed <0f> 89 60 ff ff ff 48 c1 e5 06 48 c7 43 18 00 00 00 00 48 83 44 2b
RSP: 0018:ffff888481cf7d90 EFLAGS: 00000202
RAX: 0000000000000000 RBX: ffff88887facddc8 RCX: 0000000000000000
RDX: 1ffff1110ff588b1 RSI: 0000000000000019 RDI: ffff88887fac4588
RBP: 0000000000000004 R08: 0000000000000002 R09: 0000000000043080
R10: 0009b02ea273363f R11: ffff88887fabf42b R12: ffffffff932592e0
R13: 0000000000000004 R14: 0000000000000000 R15: 00000022c880ec80
cpuidle_enter+0x4a/0xa0
do_idle+0x310/0x410
cpu_startup_entry+0x51/0x60
start_secondary+0x211/0x270
secondary_startup_64_no_verify+0x184/0x18b
</TASK>
Allocated by task 6853:
kasan_save_stack+0x1c/0x40
kasan_save_track+0x10/0x30
__kasan_kmalloc+0xa6/0xb0
__kmalloc+0x1eb/0x450
cipso_v4_sock_setattr+0x96/0x360
netlbl_sock_setattr+0x132/0x1f0
selinux_netlbl_socket_post_create+0x6c/0x110
selinux_socket_post_create+0x37b/0x7f0
security_socket_post_create+0x63/0xb0
__sock_create+0x305/0x450
__sys_socket_create.part.23+0xbd/0x130
__sys_socket+0x37/0xb0
__x64_sys_socket+0x6f/0xb0
do_syscall_64+0x83/0x160
entry_SYSCALL_64_after_hwframe+0x6e/0x76
Freed by task 6858:
kasan_save_stack+0x1c/0x40
kasan_save_track+0x10/0x30
kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x12c/0x1f0
kfree+0xed/0x2e0
inet_sock_destruct+0x54f/0x8b0
__sk_destruct+0x48/0x5b0
subflow_ulp_release+0x1f0/0x250
tcp_cleanup_ulp+0x6e/0x110
tcp_v4_destroy_sock+0x5a/0x3a0
inet_csk_destroy_sock+0x135/0x390
tcp_fin+0x416/0x5c0
tcp_data_queue+0x1bc8/0x4310
tcp_rcv_state_process+0x15a3/0x47b0
tcp_v4_do_rcv+0x2c1/0x990
tcp_v4_rcv+0x41fb/0x5ed0
ip_protocol_deliver_rcu+0x6d/0x9f0
ip_local_deliver_finish+0x278/0x360
ip_local_deliver+0x182/0x2c0
ip_rcv+0xb5/0x1c0
__netif_receive_skb_one_core+0x16e/0x1b0
process_backlog+0x1e3/0x650
__napi_poll+0xa6/0x500
net_rx_action+0x740/0xbb0
__do_softirq+0x183/0x5a4
The buggy address belongs to the object at ffff888485950880
which belongs to the cache kmalloc-64 of size 64
The buggy address is located 0 bytes inside of
64-byte region [ffff888485950880, ffff8884859508c0)
The buggy address belongs to the physical page:
page:0000000056d1e95e refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888485950700 pfn:0x485950
flags: 0x57ffffc0000800(slab|node=1|zone=2|lastcpupid=0x1fffff)
page_type: 0xffffffff()
raw: 0057ffffc0000800 ffff88810004c640 ffffea00121b8ac0 dead000000000006
raw: ffff888485950700 0000000000200019 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888485950780: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffff888485950800: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff888485950880: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
^
ffff888485950900: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ffff888485950980: 00 00 00 00 00 01 fc fc fc fc fc fc fc fc fc fc
Something similar (a refcount underflow) happens with CALIPSO/IPv6. Fix
this by duplicating IP / IPv6 options after clone, so that
ip{,6}_sock_destruct() doesn't end up freeing the same memory area twice.
Fixes: cf7da0d66c ("mptcp: Create SUBFLOW socket for incoming connections")
Cc: stable@vger.kernel.org
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-8-162e87e48497@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commands 'ss -M' are used in script mptcp_join.sh to display only MPTCP
sockets. So it must be checked if ss tool supports MPTCP in this script.
Fixes: e274f71540 ("selftests: mptcp: add subflow limits test-cases")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-7-162e87e48497@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After the blamed commit below, the send buffer auto-tuning can
happen after that the mptcp_propagate_sndbuf() completes - via
the delegated action infrastructure.
We must check for write space even after such change or we risk
missing the wake-up event.
Fixes: 8005184fd1 ("mptcp: refactor sndbuf auto-tuning")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-6-162e87e48497@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
when inserting not contiguous data in the subflow write queue,
the protocol creates a new skb and prevent the TCP stack from
merging it later with already queued skbs by setting the EOR marker.
Still no push flag is explicitly set at the end of previous GSO
packet, making the aggregation on the receiver side sub-optimal -
and packetdrill self-tests less predictable.
Explicitly mark the end of not contiguous DSS with the push flag.
Fixes: 6d0060f600 ("mptcp: Write MPTCP DSS headers to outgoing data packets")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-4-162e87e48497@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After the 'Fixes' commit mentioned below, the client side might print
the following warning once when a subflow is fully established at the
reception of any valid additional ack:
MPTCP: bogus mpc option on established client sk
That's a normal situation, and no warning should be printed for that. We
can then skip the check when the label is used.
Fixes: e4a0fa47e8 ("mptcp: corner case locking for rx path fields initialization")
Cc: stable@vger.kernel.org
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-3-162e87e48497@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now both a v4 address and a v4-mapped address are supported when
destroying a userspace pm subflow, this patch adds a second subflow
to "userspace pm add & remove address" test, and two subflows could
be removed two different ways, one with the v4mapped and one with v4.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/387
Fixes: 48d73f609d ("selftests: mptcp: update userspace pm addr tests")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-2-162e87e48497@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Address family of server side mismatches with that of client side, like
in "userspace pm add & remove address" test:
userspace_pm_add_addr $ns1 10.0.2.1 10
userspace_pm_rm_sf $ns1 "::ffff:10.0.2.1" $SUB_ESTABLISHED
That's because on the server side, the family is set to AF_INET6 and the
v4 address is mapped in a v6 one.
This patch fixes this issue. In mptcp_pm_nl_subflow_destroy_doit(), before
checking local address family with remote address family, map an IPv4
address to an IPv6 address if the pair is a v4-mapped address.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/387
Fixes: 702c2f646d ("mptcp: netlink: allow userspace-driven subflow establishment")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240223-upstream-net-20240223-misc-fixes-v1-1-162e87e48497@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This fixes a possible UAF in if_nlmsg_size(),
which can run without RTNL.
Add rcu protection to "struct dpll_pin"
Move netdev_dpll_pin() from netdevice.h to dpll.h to
decrease name pollution.
Note: This looks possible to no longer acquire RTNL in
netdev_dpll_pin_assign() later in net-next.
v2: do not force rcu_read_lock() in rtnl_dpll_pin_size() (Jiri Pirko)
Fixes: 5f18426928 ("netdev: expose DPLL pin handle for netdevice")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Cc: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240223123208.3543319-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Same as LAN7800, LAN7850 can be used without EEPROM. If EEPROM is not
present or not flashed, LAN7850 will fail to sync the speed detected by the PHY
with the MAC. In case link speed is 100Mbit, it will accidentally work,
otherwise no data can be transferred.
Better way would be to implement link_up callback, or set auto speed
configuration unconditionally. But this changes would be more intrusive.
So, for now, set it only if no EEPROM is found.
Fixes: e69647a19c ("lan78xx: Set ASD in MAC_CR when EEE is enabled.")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240222123839.2816561-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the driver detects that the controller is not ready before sending the
first IOC facts command, it will wait for a maximum of 10 seconds for it to
become ready. However, even if the controller becomes ready within 10
seconds, the driver will still issue a diagnostic reset.
Modify the driver to avoid sending a diag reset if the controller becomes
ready within the 10-second wait time.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20240221071724.14986-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Doubling the number of PHYs also doubled the stack usage of this function,
exceeding the 32-bit limit of 1024 bytes:
drivers/scsi/mpi3mr/mpi3mr_transport.c: In function 'mpi3mr_refresh_sas_ports':
drivers/scsi/mpi3mr/mpi3mr_transport.c:1818:1: error: the frame size of 1636 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Since the sas_io_unit_pg0 structure is already allocated dynamically, use
the same method here. The size of the allocation can be smaller based on
the actual number of phys now, so use this as an upper bound.
Fixes: cb5b608946 ("scsi: mpi3mr: Increase maximum number of PHYs to 64 from 32")
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240123130754.2011469-1-arnd@kernel.org
Tested-by: John Garry <john.g.garry@oracle.com> #build only
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since MOCK_HUGE_PAGE_SIZE was introduced it allows the core code to invoke
mock with large page sizes. This confuses the validation logic that checks
that map/unmap are paired.
This is because the page size computed for map is based on the physical
address and in many cases will always be the base page size, however the
entire range generated by iommufd will be passed to map.
Randomly iommufd can see small groups of physically contiguous pages,
(say 8k unaligned and grouped together), but that group crosses a huge
page boundary. The map side will observe this as a contiguous run and mark
it accordingly, but there is a chance the unmap side will end up
terminating interior huge pages in the middle of that group and trigger a
validation failure. Meaning the validation only works if the core code
passes the iova/length directly from iommufd to mock.
syzkaller randomly hits this with failures like:
WARNING: CPU: 0 PID: 11568 at drivers/iommu/iommufd/selftest.c:461 mock_domain_unmap_pages+0x1c0/0x250
Modules linked in:
CPU: 0 PID: 11568 Comm: syz-executor.0 Not tainted 6.8.0-rc3+ #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
RIP: 0010:mock_domain_unmap_pages+0x1c0/0x250
Code: 2b e8 94 37 0f ff 48 d1 eb 31 ff 48 b8 00 00 00 00 00 00 20 00 48 21 c3 48 89 de e8 aa 32 0f ff 48 85 db 75 07 e8 70 37 0f ff <0f> 0b e8 69 37 0f ff 31 f6 31 ff e8 90 32 0f ff e8 5b 37 0f ff 4c
RSP: 0018:ffff88800e707490 EFLAGS: 00010293
RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffff822dfae6
RDX: ffff88800cf86400 RSI: ffffffff822dfaf0 RDI: 0000000000000007
RBP: ffff88800e7074d8 R08: 0000000000000000 R09: ffffed1001167c90
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000001500000
R13: 0000000000083000 R14: 0000000000000001 R15: 0000000000000800
FS: 0000555556048480(0000) GS:ffff88806d400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000001b2dc23000 CR3: 0000000008cbb000 CR4: 0000000000350eb0
Call Trace:
<TASK>
__iommu_unmap+0x281/0x520
iommu_unmap+0xc9/0x180
iopt_area_unmap_domain_range+0x1b1/0x290
iopt_area_unpin_domain+0x590/0x800
__iopt_area_unfill_domain+0x22e/0x650
iopt_area_unfill_domain+0x47/0x60
iopt_unfill_domain+0x187/0x590
iopt_table_remove_domain+0x267/0x2d0
iommufd_hwpt_paging_destroy+0x1f1/0x370
iommufd_object_remove+0x2a3/0x490
iommufd_device_detach+0x23a/0x2c0
iommufd_selftest_destroy+0x7a/0xf0
iommufd_fops_release+0x1d3/0x340
__fput+0x272/0xb50
__fput_sync+0x4b/0x60
__x64_sys_close+0x8b/0x110
do_syscall_64+0x71/0x140
entry_SYSCALL_64_after_hwframe+0x46/0x4e
Do the simple thing and just disable the validation when the huge page
tests are being run.
Fixes: 7db521e23f ("iommufd/selftest: Hugepage mock domain support")
Link: https://lore.kernel.org/r/0-v1-1e17e60a5c8a+103fb-iommufd_mock_hugepg_jgg@nvidia.com
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Syzkaller reported the following bug:
general protection fault, probably for non-canonical address 0xdffffc0000000038: 0000 [#1] SMP KASAN
KASAN: null-ptr-deref in range [0x00000000000001c0-0x00000000000001c7]
Call Trace:
lock_acquire
lock_acquire+0x1ce/0x4f0
down_read+0x93/0x4a0
iommufd_test_syz_conv_iova+0x56/0x1f0
iommufd_test_access_rw.isra.0+0x2ec/0x390
iommufd_test+0x1058/0x1e30
iommufd_fops_ioctl+0x381/0x510
vfs_ioctl
__do_sys_ioctl
__se_sys_ioctl
__x64_sys_ioctl+0x170/0x1e0
do_syscall_x64
do_syscall_64+0x71/0x140
This is because the new iommufd_access_change_ioas() sets access->ioas to
NULL during its process, so the lock might be gone in a concurrent racing
context.
Fix this by doing the same access->ioas sanity as iommufd_access_rw() and
iommufd_access_pin_pages() functions do.
Cc: stable@vger.kernel.org
Fixes: 9227da7816 ("iommufd: Add iommufd_access_change_ioas(_id) helpers")
Link: https://lore.kernel.org/r/3f1932acaf1dd494d404c04364d73ce8f57f3e5e.1708636627.git.nicolinc@nvidia.com
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Syzkaller reported the following bug:
sysfs: cannot create duplicate filename '/devices/iommufd_mock4'
Call Trace:
sysfs_warn_dup+0x71/0x90
sysfs_create_dir_ns+0x1ee/0x260
? sysfs_create_mount_point+0x80/0x80
? spin_bug+0x1d0/0x1d0
? do_raw_spin_unlock+0x54/0x220
kobject_add_internal+0x221/0x970
kobject_add+0x11c/0x1e0
? lockdep_hardirqs_on_prepare+0x273/0x3e0
? kset_create_and_add+0x160/0x160
? kobject_put+0x5d/0x390
? bus_get_dev_root+0x4a/0x60
? kobject_put+0x5d/0x390
device_add+0x1d5/0x1550
? __fw_devlink_link_to_consumers.isra.0+0x1f0/0x1f0
? __init_waitqueue_head+0xcb/0x150
iommufd_test+0x462/0x3b60
? lock_release+0x1fe/0x640
? __might_fault+0x117/0x170
? reacquire_held_locks+0x4b0/0x4b0
? iommufd_selftest_destroy+0xd0/0xd0
? __might_fault+0xbe/0x170
iommufd_fops_ioctl+0x256/0x350
? iommufd_option+0x180/0x180
? __lock_acquire+0x1755/0x45f0
__x64_sys_ioctl+0xa13/0x1640
The bug is triggered when Syzkaller created multiple mock devices but
didn't destroy them in the same sequence, messing up the mock_dev_num
counter. Replace the atomic with an mock_dev_ida.
Cc: stable@vger.kernel.org
Fixes: 23a1b46f15 ("iommufd/selftest: Make the mock iommu driver into a real driver")
Link: https://lore.kernel.org/r/5af41d5af6d5c013cc51de01427abb8141b3587e.1708636627.git.nicolinc@nvidia.com
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Syzkaller reported the following WARN_ON:
WARNING: CPU: 1 PID: 4738 at drivers/iommu/iommufd/io_pagetable.c:1360
Call Trace:
iommufd_access_change_ioas+0x2fe/0x4e0
iommufd_access_destroy_object+0x50/0xb0
iommufd_object_remove+0x2a3/0x490
iommufd_object_destroy_user
iommufd_access_destroy+0x71/0xb0
iommufd_test_staccess_release+0x89/0xd0
__fput+0x272/0xb50
__fput_sync+0x4b/0x60
__do_sys_close
__se_sys_close
__x64_sys_close+0x8b/0x110
do_syscall_x64
The mismatch between the access pointer in the list and the passed-in
pointer is resulting from an overwrite of access->iopt_access_list_id, in
iopt_add_access(). Called from iommufd_access_change_ioas() when
xa_alloc() succeeds but iopt_calculate_iova_alignment() fails.
Add a new_id in iopt_add_access() and only update iopt_access_list_id when
returning successfully.
Cc: stable@vger.kernel.org
Fixes: 9227da7816 ("iommufd: Add iommufd_access_change_ioas(_id) helpers")
Link: https://lore.kernel.org/r/2dda7acb25b8562ec5f1310de828ef5da9ef509c.1708636627.git.nicolinc@nvidia.com
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
but could not be used in practice so they are being removed.
Regarding the SPI-NAND area, Gigadevice chips were not using the right
buffer for an ECC status check operation.
Aside from these driver fixes, there is also a refcount fix in the MTD
core nodes parsing logic.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmXccMwACgkQJWrqGEe9
VoRSjAf/SdgiZdXz6Fv2uUQYXsHNXO9PnFPSzJ8XNg16g4Jdm/uG0dTIN9W12ZTK
QtI2v8+HLtmIzxcGpHEVSzxMTfMbNbB+CibZm+lQFABeqxrhasFHAEDE0Nmo0dNs
/Dh5Em6fxxOW/pYUoPQk9zm5RNNg+yr9eQk9FKrv723Wprk6tjHjQQJEpUchtXUz
B/qfNSszIQUHPIUtYdNc0A0E1Q4Dr525gBnKFP2lvd6OmjjI35fJ4QvOQuVCQ5b9
Q01y50SojypoFMb+SjiYxFBSnjO3ZECnbf4wvAE0S08tsXUdOfg4ksoiciZbC4mz
6BCw+MooPwi2vUPldeITlAm0Ij0G1A==
=0Nf5
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-6.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
"Many NAND page layouts have been added to the Marvell NAND controller
but could not be used in practice so they are being removed.
Regarding the SPI-NAND area, Gigadevice chips were not using the right
buffer for an ECC status check operation.
Aside from these driver fixes, there is also a refcount fix in the MTD
core nodes parsing logic"
* tag 'mtd/fixes-for-6.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: marvell: fix layouts
mtd: Fix possible refcounting issue when going through partition nodes
mtd: spinand: gigadevice: Fix the get ecc status issue
-----BEGIN PGP SIGNATURE-----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=mBP6
-----END PGP SIGNATURE-----
Merge tag 'for-6.8-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A more fixes for recently reported or discovered problems:
- fix corner case of send that would generate potentially large
stream of zeros if there's a hole at the end of the file
- fix chunk validation in zoned mode on conventional zones, it was
possible to create chunks that would not be allowed on sequential
zones
- fix validation of dev-replace ioctl filenames
- fix KCSAN warnings about access to block reserve struct members"
* tag 'for-6.8-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix data race at btrfs_use_block_rsv() when accessing block reserve
btrfs: fix data races when accessing the reserved amount of block reserves
btrfs: send: don't issue unnecessary zero writes for trailing hole
btrfs: dev-replace: properly validate device names
btrfs: zoned: don't skip block group profile checks on conventional zones
The addition of bal_rank_mask with encoding version 17 was merged
into ceph.git in Oct 2022 and made it into v18.2.0 release normally.
A few months later, the much delayed addition of max_xattr_size got
merged, also with encoding version 17, placed before bal_rank_mask
in the encoding -- but it didn't make v18.2.0 release.
The way this ended up being resolved on the MDS side is that
bal_rank_mask will continue to be encoded in version 17 while
max_xattr_size is now encoded in version 18. This does mean that
older kernels will misdecode version 17, but this is also true for
v18.2.0 and v18.2.1 clients in userspace.
The best we can do is backport this adjustment -- see ceph.git
commit 78abfeaff27fee343fb664db633de5b221699a73 for details.
[ idryomov: changelog ]
Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/64440
Fixes: d93231a6bc ("ceph: prevent a client from exceeding the MDS maximum xattr size")
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Patrick Donnelly <pdonnell@ibm.com>
Reviewed-by: Venky Shankar <vshankar@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
When CONFIG_NTFS3_LZX_XPRESS is not set then we get the following build
error:
fs/ntfs3/frecord.c:2460:16: error: unused variable ‘i_size’
Signed-off-by: Mark O'Donovan <shiftee@posteo.net>
Fixes: 4fd6c08a16 ("fs/ntfs3: Use i_size_read and i_size_write")
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When linking or renaming a file, if only one of the source or
destination directory is backed by an S_PRIVATE inode, then the related
set of layer masks would be used as uninitialized by
is_access_to_paths_allowed(). This would result to indeterministic
access for one side instead of always being allowed.
This bug could only be triggered with a mounted filesystem containing
both S_PRIVATE and !S_PRIVATE inodes, which doesn't seem possible.
The collect_domain_accesses() calls return early if
is_nouser_or_private() returns false, which means that the directory's
superblock has SB_NOUSER or its inode has S_PRIVATE. Because rename or
link actions are only allowed on the same mounted filesystem, the
superblock is always the same for both source and destination
directories. However, it might be possible in theory to have an
S_PRIVATE parent source inode with an !S_PRIVATE parent destination
inode, or vice versa.
To make sure this case is not an issue, explicitly initialized both set
of layer masks to 0, which means to allow all actions on the related
side. If at least on side has !S_PRIVATE, then
collect_domain_accesses() and is_access_to_paths_allowed() check for the
required access rights.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Günther Noack <gnoack@google.com>
Cc: Jann Horn <jannh@google.com>
Cc: Shervin Oloumi <enlightened@chromium.org>
Cc: stable@vger.kernel.org
Fixes: b91c3e4ea7 ("landlock: Add support for file reparenting with LANDLOCK_ACCESS_FS_REFER")
Link: https://lore.kernel.org/r/20240219190345.2928627-1-mic@digikod.net
Signed-off-by: Mickaël Salaün <mic@digikod.net>
MKTME repurposes the high bit of physical address to key id for encryption
key and, even though MAXPHYADDR in CPUID[0x80000008] remains the same,
the valid bits in the MTRR mask register are based on the reduced number
of physical address bits.
detect_tme() in arch/x86/kernel/cpu/intel.c detects TME and subtracts
it from the total usable physical bits, but it is called too late.
Move the call to early_init_intel() so that it is called in setup_arch(),
before MTRRs are setup.
This fixes boot on TDX-enabled systems, which until now only worked with
"disable_mtrr_cleanup". Without the patch, the values written to the
MTRRs mask registers were 52-bit wide (e.g. 0x000fffff_80000800) and
the writes failed; with the patch, the values are 46-bit wide, which
matches the reduced MAXPHYADDR that is shown in /proc/cpuinfo.
Reported-by: Zixi Chen <zixchen@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240131230902.1867092-3-pbonzini%40redhat.com
In commit fbf6449f84 ("x86/sev-es: Set x86_virt_bits to the correct
value straight away, instead of a two-phase approach"), the initialization
of c->x86_phys_bits was moved after this_cpu->c_early_init(c). This is
incorrect because early_init_amd() expected to be able to reduce the
value according to the contents of CPUID leaf 0x8000001f.
Fortunately, the bug was negated by init_amd()'s call to early_init_amd(),
which does reduce x86_phys_bits in the end. However, this is very
late in the boot process and, most notably, the wrong value is used for
x86_phys_bits when setting up MTRRs.
To fix this, call get_cpu_address_sizes() as soon as X86_FEATURE_CPUID is
set/cleared, and c->extended_cpuid_level is retrieved.
Fixes: fbf6449f84 ("x86/sev-es: Set x86_virt_bits to the correct value straight away, instead of a two-phase approach")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240131230902.1867092-2-pbonzini%40redhat.com
Commit a5a923038d (fbdev: fbcon: Properly revert changes when
vc_resize() failed) started restoring old font data upon failure (of
vc_resize()). But it performs so only for user fonts. It means that the
"system"/internal fonts are not restored at all. So in result, the very
first call to fbcon_do_set_font() performs no restore at all upon
failing vc_resize().
This can be reproduced by Syzkaller to crash the system on the next
invocation of font_get(). It's rather hard to hit the allocation failure
in vc_resize() on the first font_set(), but not impossible. Esp. if
fault injection is used to aid the execution/failure. It was
demonstrated by Sirius:
BUG: unable to handle page fault for address: fffffffffffffff8
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD cb7b067 P4D cb7b067 PUD cb7d067 PMD 0
Oops: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 8007 Comm: poc Not tainted 6.7.0-g9d1694dc91ce #20
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
RIP: 0010:fbcon_get_font+0x229/0x800 drivers/video/fbdev/core/fbcon.c:2286
Call Trace:
<TASK>
con_font_get drivers/tty/vt/vt.c:4558 [inline]
con_font_op+0x1fc/0xf20 drivers/tty/vt/vt.c:4673
vt_k_ioctl drivers/tty/vt/vt_ioctl.c:474 [inline]
vt_ioctl+0x632/0x2ec0 drivers/tty/vt/vt_ioctl.c:752
tty_ioctl+0x6f8/0x1570 drivers/tty/tty_io.c:2803
vfs_ioctl fs/ioctl.c:51 [inline]
...
So restore the font data in any case, not only for user fonts. Note the
later 'if' is now protected by 'old_userfont' and not 'old_data' as the
latter is always set now. (And it is supposed to be non-NULL. Otherwise
we would see the bug above again.)
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Fixes: a5a923038d ("fbdev: fbcon: Properly revert changes when vc_resize() failed")
Reported-and-tested-by: Ubisectech Sirius <bugreport@ubisectech.com>
Cc: Ubisectech Sirius <bugreport@ubisectech.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20240208114411.14604-1-jirislaby@kernel.org
At least the device test requires that no other driver using TTM is
loaded. So make those unit tests depend on UML || COMPILE_TEST to
prevent people from trying them on bare metal.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/all/20240219230116.77b8ad68@yea/
Tegra DRM doesn't support display on Tegra234 and later, so make sure
not to remove any existing framebuffers in that case.
v2: - add comments explaining how this situation can come about
- clear DRIVER_MODESET and DRIVER_ATOMIC feature bits
Fixes: 6848c291a5 ("drm/aperture: Convert drivers to aperture interfaces")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240223150333.1401582-1-thierry.reding@gmail.com
It seems that if userspace provides a correct IFA_TARGET_NETNSID value
but no IFA_ADDRESS and IFA_LOCAL attributes, inet6_rtm_getaddr()
returns -EINVAL with an elevated "struct net" refcount.
Fixes: 6ecf4c37eb ("ipv6: enable IFA_TARGET_NETNSID for RTM_GETADDR")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that we keep GRO flag in sync when XDP is disabled while
the device is closed.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
veth sets NETIF_F_GRO automatically when XDP is enabled,
because both features use the same NAPI machinery.
The logic to clear NETIF_F_GRO sits in veth_disable_xdp() which
is called both on ndo_stop and when XDP is turned off.
To avoid the flag from being cleared when the device is brought
down, the clearing is skipped when IFF_UP is not set.
Bringing the device down should indeed not modify its features.
Unfortunately, this means that clearing is also skipped when
XDP is disabled _while_ the device is down. And there's nothing
on the open path to bring the device features back into sync.
IOW if user enables XDP, disables it and then brings the device
up we'll end up with a stray GRO flag set but no NAPI instances.
We don't depend on the GRO flag on the datapath, so the datapath
won't crash. We will crash (or hang), however, next time features
are sync'ed (either by user via ethtool or peer changing its config).
The GRO flag will go away, and veth will try to disable the NAPIs.
But the open path never created them since XDP was off, the GRO flag
was a stray. If NAPI was initialized before we'll hang in napi_disable().
If it never was we'll crash trying to stop uninitialized hrtimer.
Move the GRO flag updates to the XDP enable / disable paths,
instead of mixing them with the ndo_open / ndo_close paths.
Fixes: d3256efd8e ("veth: allow enabling NAPI even without XDP")
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: syzbot+039399a9b96297ddedca@syzkaller.appspotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
