Ring expansion checker may incorrectly assume a completely full ring
is empty, missing the need for expansion.
This is due to a special empty ring case where the dequeue ends up
ahead of the enqueue pointer. This is seen when enqueued TRBs fill up
exactly a segment, with enqueue then pointing to the end link TRB.
Once those TRBs are handled the dequeue pointer will follow the link
TRB and end up pointing to the first entry on the next segment, past
the enqueue.
This same enqueue - dequeue condition can be true if a ring is full,
with enqueue ending on that last link TRB before the dequeue pointer
on the next segment.
This can be seen when queuing several ~510 small URBs via usbfs in
one go before a single one is handled (i.e. dequeue not moved from first
entry in segment).
Expand the ring already when enqueue reaches the link TRB before the
dequeue segment, instead of expanding it when enqueue moves into the
dequeue segment.
Reported-by: Chris Yokum <linux-usb@mail.totalphase.com>
Closes: https://lore.kernel.org/all/949223224.833962.1709339266739.JavaMail.zimbra@totalphase.com
Tested-by: Chris Yokum <linux-usb@mail.totalphase.com>
Fixes: f5af638f06 ("xhci: Fix transfer ring expansion size calculation")
Cc: stable@vger.kernel.org # v6.5+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240305132312.955171-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While connecting to a Linux host with CDC_NCM_NTB_DEF_SIZE_TX
set to 65536, it has been observed that we receive short packets,
which come at interval of 5-10 seconds sometimes and have block
length zero but still contain 1-2 valid datagrams present.
According to the NCM spec:
"If wBlockLength = 0x0000, the block is terminated by a
short packet. In this case, the USB transfer must still
be shorter than dwNtbInMaxSize or dwNtbOutMaxSize. If
exactly dwNtbInMaxSize or dwNtbOutMaxSize bytes are sent,
and the size is a multiple of wMaxPacketSize for the
given pipe, then no ZLP shall be sent.
wBlockLength= 0x0000 must be used with extreme care, because
of the possibility that the host and device may get out of
sync, and because of test issues.
wBlockLength = 0x0000 allows the sender to reduce latency by
starting to send a very large NTB, and then shortening it when
the sender discovers that there’s not sufficient data to justify
sending a large NTB"
However, there is a potential issue with the current implementation,
as it checks for the occurrence of multiple NTBs in a single
giveback by verifying if the leftover bytes to be processed is zero
or not. If the block length reads zero, we would process the same
NTB infintely because the leftover bytes is never zero and it leads
to a crash. Fix this by bailing out if block length reads zero.
Cc: stable@vger.kernel.org
Fixes: 427694cfaa ("usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240228115441.2105585-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DisplayPort driver's sysfs nodes may be present to the userspace before
typec_altmode_set_drvdata() completes in dp_altmode_probe. This means that
a sysfs read can trigger a NULL pointer error by deferencing dp->hpd in
hpd_show or dp->lock in pin_assignment_show, as dev_get_drvdata() returns
NULL in those cases.
Remove manual sysfs node creation in favor of adding attribute group as
default for devices bound to the driver. The ATTRIBUTE_GROUPS() macro is
not used here otherwise the path to the sysfs nodes is no longer compliant
with the ABI.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Link: https://lore.kernel.org/r/20240229001101.3889432-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While commit 69f89168b3 ("usb: typec: tpcm: Fix issues with power being
removed during reset") fixes the boot issues for bus powered devices such
as LibreTech Renegade Elite/Firefly, it trades off the CC pins NOT being
Hi-Zed during errory recovery (i.e PORT_RESET) for devices which are NOT
bus powered(a.k.a self powered). This change Hi-Zs the CC pins only for
self powered devices, thus preventing brown out for bus powered devices
Adhering to spec is gaining more importance due to the Common charger
initiative enforced by the European Union.
Quoting from the spec:
4.5.2.2.2.1 ErrorRecovery State Requirements
The port shall not drive VBUS or VCONN, and shall present a
high-impedance to ground (above zOPEN) on its CC1 and CC2 pins.
Hi-Zing the CC pins is the inteded behavior for PORT_RESET.
CC pins are set to default state after tErrorRecovery in
PORT_RESET_WAIT_OFF.
4.5.2.2.2.2 Exiting From ErrorRecovery State
A Sink shall transition to Unattached.SNK after tErrorRecovery.
A Source shall transition to Unattached.SRC after tErrorRecovery.
Fixes: 69f89168b3 ("usb: typec: tpcm: Fix issues with power being removed during reset")
Cc: stable@vger.kernel.org
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240228000512.746252-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SM8550 and SM8650 Qualcomm platforms a call to UCSI_GET_PDOS for
non-PD partners will cause a firmware crash with no
easy way to recover from it.
Add UCSI_NO_PARTNER_PDOS quirk for those platform until we find
a way to properly handle the crash.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240223-topic-sm8550-upstream-ucsi-no-pdos-v1-1-8900ad510944@linaro.org
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The isd200 sub-driver in usb-storage uses the HEADS and SECTORS values
in the ATA ID information to calculate cylinder and head values when
creating a CDB for READ or WRITE commands. The calculation involves
division and modulus operations, which will cause a crash if either of
these values is 0. While this never happens with a genuine device, it
could happen with a flawed or subversive emulation, as reported by the
syzbot fuzzer.
Protect against this possibility by refusing to bind to the device if
either the ATA_ID_HEADS or ATA_ID_SECTORS value in the device's ID
information is 0. This requires isd200_Initialization() to return a
negative error code when initialization fails; currently it always
returns 0 (even when there is an error).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+28748250ab47a8f04100@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-usb/0000000000003eb868061245ba7f@google.com/
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/b1e605ea-333f-4ac0-9511-da04f411763e@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small USB fixes for 6.8-rc6 to resolve some reported
problems. These include:
- regression fixes with typec tpcm code as reported by many
- cdnsp and cdns3 driver fixes
- usb role setting code bugfixes
- build fix for uhci driver
- ncm gadget driver bugfix
- MAINTAINERS entry update
All of these have been in linux-next all week with no reported issues
and there is at least one fix in here that is in Thorsten's regression
list that is being tracked.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZdtGEA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymzsgCg2IsWqIR72XUGsa5rrbRnskOP/G4An24BmUb6
t34d0VjiHagZTFlfRx6g
=eOL1
-----END PGP SIGNATURE-----
Merge tag 'usb-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 6.8-rc6 to resolve some reported
problems. These include:
- regression fixes with typec tpcm code as reported by many
- cdnsp and cdns3 driver fixes
- usb role setting code bugfixes
- build fix for uhci driver
- ncm gadget driver bugfix
- MAINTAINERS entry update
All of these have been in linux-next all week with no reported issues
and there is at least one fix in here that is in Thorsten's regression
list that is being tracked"
* tag 'usb-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tpcm: Fix issues with power being removed during reset
MAINTAINERS: Drop myself as maintainer of TYPEC port controller drivers
usb: gadget: ncm: Avoid dropping datagrams of properly parsed NTBs
Revert "usb: typec: tcpm: reset counter when enter into unattached state after try role"
usb: gadget: omap_udc: fix USB gadget regression on Palm TE
usb: dwc3: gadget: Don't disconnect if not started
usb: cdns3: fix memory double free when handle zero packet
usb: cdns3: fixed memory use after free at cdns3_gadget_ep_disable()
usb: roles: don't get/set_role() when usb_role_switch is unregistered
usb: roles: fix NULL pointer issue when put module's reference
usb: cdnsp: fixed issue with incorrect detecting CDNSP family controllers
usb: cdnsp: blocked some cdns3 specific code
usb: uhci-grlib: Explicitly include linux/platform_device.h
Six fixes: the four driver ones are pretty trivial. The larger two
core changes are to try to fix various USB attached devices which have
somewhat eccentric ways of handling the VPD and other mode pages which
necessitate multiple revalidates (that were removed in the interests
of efficiency) and updating the heuristic for supported VPD pages.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZdkyyyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishS2KAP0V8RVm
U1gUoE4doIV9WdK8Dv0MUxnOpYVvjhRjM8PA1QEAwaPJivC91smxJv4MOIDq0PL3
9qyMwQq4jWH/2zS14p8=
=8aq+
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fixes: the four driver ones are pretty trivial.
The larger two core changes are to try to fix various USB attached
devices which have somewhat eccentric ways of handling the VPD and
other mode pages which necessitate multiple revalidates (that were
removed in the interests of efficiency) and updating the heuristic for
supported VPD pages"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: jazz_esp: Only build if SCSI core is builtin
scsi: smartpqi: Fix disable_managed_interrupts
scsi: ufs: Uninitialized variable in ufshcd_devfreq_target()
scsi: target: pscsi: Fix bio_put() for error case
scsi: core: Consult supported VPD page list prior to fetching page
scsi: sd: usb_storage: uas: Access media prior to querying device properties
Since the merge of b717dfbf73 ("Revert "usb: typec: tcpm: fix
cc role at port reset"") into mainline the LibreTech Renegade
Elite/Firefly has died during boot, the main symptom observed in testing
is a sudden stop in console output. Gábor Stefanik identified in review
that the patch would cause power to be removed from devices without
batteries (like this board), observing that while the patch is correct
according to the spec this appears to be an oversight in the spec.
Given that the change makes previously working systems unusable let's
revert it, there was some discussion of identifying systems that have
alternative power and implementing the standards conforming behaviour in
only that case.
Fixes: b717dfbf73 ("Revert "usb: typec: tcpm: fix cc role at port reset"")
Cc: stable <stable@kernel.org>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240212-usb-fix-renegade-v1-1-22c43c88d635@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is observed sometimes when tethering is used over NCM with Windows 11
as host, at some instances, the gadget_giveback has one byte appended at
the end of a proper NTB. When the NTB is parsed, unwrap call looks for
any leftover bytes in SKB provided by u_ether and if there are any pending
bytes, it treats them as a separate NTB and parses it. But in case the
second NTB (as per unwrap call) is faulty/corrupt, all the datagrams that
were parsed properly in the first NTB and saved in rx_list are dropped.
Adding a few custom traces showed the following:
[002] d..1 7828.532866: dwc3_gadget_giveback: ep1out:
req 000000003868811a length 1025/16384 zsI ==> 0
[002] d..1 7828.532867: ncm_unwrap_ntb: K: ncm_unwrap_ntb toprocess: 1025
[002] d..1 7828.532867: ncm_unwrap_ntb: K: ncm_unwrap_ntb nth: 1751999342
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb seq: 0xce67
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb blk_len: 0x400
[002] d..1 7828.532868: ncm_unwrap_ntb: K: ncm_unwrap_ntb ndp_len: 0x10
[002] d..1 7828.532869: ncm_unwrap_ntb: K: Parsed NTB with 1 frames
In this case, the giveback is of 1025 bytes and block length is 1024.
The rest 1 byte (which is 0x00) won't be parsed resulting in drop of
all datagrams in rx_list.
Same is case with packets of size 2048:
[002] d..1 7828.557948: dwc3_gadget_giveback: ep1out:
req 0000000011dfd96e length 2049/16384 zsI ==> 0
[002] d..1 7828.557949: ncm_unwrap_ntb: K: ncm_unwrap_ntb nth: 1751999342
[002] d..1 7828.557950: ncm_unwrap_ntb: K: ncm_unwrap_ntb blk_len: 0x800
Lecroy shows one byte coming in extra confirming that the byte is coming
in from PC:
Transfer 2959 - Bytes Transferred(1025) Timestamp((18.524 843 590)
- Transaction 8391 - Data(1025 bytes) Timestamp(18.524 843 590)
--- Packet 4063861
Data(1024 bytes)
Duration(2.117us) Idle(14.700ns) Timestamp(18.524 843 590)
--- Packet 4063863
Data(1 byte)
Duration(66.160ns) Time(282.000ns) Timestamp(18.524 845 722)
According to Windows driver, no ZLP is needed if wBlockLength is non-zero,
because the non-zero wBlockLength has already told the function side the
size of transfer to be expected. However, there are in-market NCM devices
that rely on ZLP as long as the wBlockLength is multiple of wMaxPacketSize.
To deal with such devices, it pads an extra 0 at end so the transfer is no
longer multiple of wMaxPacketSize.
Cc: <stable@vger.kernel.org>
Fixes: 9f6ce4240a ("usb: gadget: f_ncm.c added")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240205074650.200304-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reverted commit makes the state machine only ever go from SRC_ATTACH_WAIT
to SNK_TRY in endless loop when toggling. After revert it goes to SRC_ATTACHED
after initially trying SNK_TRY earlier, as it should for toggling to ever detect
the power source mode and the port is again able to provide power to attached
power sinks.
This reverts commit 2d6d801270.
Cc: stable@vger.kernel.org
Fixes: 2d6d801270 ("usb: typec: tcpm: reset counter when enter into unattached state after try role")
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20240217162023.1719738-1-megi@xff.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When upgrading from 6.1 LTS to 6.6 LTS, I noticed the ethernet gadget
stopped working on Palm TE.
Commit 8825acd7cc ("ARM: omap1: remove dead code") deleted Palm TE from
machine_without_vbus_sense(), although the board is still used. Fix that.
Fixes: 8825acd7cc ("ARM: omap1: remove dead code")
Cc: stable <stable@kernel.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240217192042.GA372205@darkstar.musicnaut.iki.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
829 if (request->complete) {
830 spin_unlock(&priv_dev->lock);
831 usb_gadget_giveback_request(&priv_ep->endpoint,
832 request);
833 spin_lock(&priv_dev->lock);
834 }
835
836 if (request->buf == priv_dev->zlp_buf)
837 cdns3_gadget_ep_free_request(&priv_ep->endpoint, request);
Driver append an additional zero packet request when queue a packet, which
length mod max packet size is 0. When transfer complete, run to line 831,
usb_gadget_giveback_request() will free this requestion. 836 condition is
true, so cdns3_gadget_ep_free_request() free this request again.
Log:
[ 1920.140696][ T150] BUG: KFENCE: use-after-free read in cdns3_gadget_giveback+0x134/0x2c0 [cdns3]
[ 1920.140696][ T150]
[ 1920.151837][ T150] Use-after-free read at 0x000000003d1cd10b (in kfence-#36):
[ 1920.159082][ T150] cdns3_gadget_giveback+0x134/0x2c0 [cdns3]
[ 1920.164988][ T150] cdns3_transfer_completed+0x438/0x5f8 [cdns3]
Add check at line 829, skip call usb_gadget_giveback_request() if it is
additional zero length packet request. Needn't call
usb_gadget_giveback_request() because it is allocated in this driver.
Cc: stable@vger.kernel.org
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240202154217.661867-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a possibility that usb_role_switch device is unregistered before
the user put usb_role_switch. In this case, the user may still want to
get/set_role() since the user can't sense the changes of usb_role_switch.
This will add a flag to show if usb_role_switch is already registered and
avoid unwanted behaviors.
Fixes: fde0aa6c17 ("usb: common: Small class for USB role switches")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240129093739.2371530-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current design, usb role class driver will get usb_role_switch parent's
module reference after the user get usb_role_switch device and put the
reference after the user put the usb_role_switch device. However, the
parent device of usb_role_switch may be removed before the user put the
usb_role_switch. If so, then, NULL pointer issue will be met when the user
put the parent module's reference.
This will save the module pointer in structure of usb_role_switch. Then,
we don't need to find module by iterating long relations.
Fixes: 5c54fcac9a ("usb: roles: Take care of driver module reference counting")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240129093739.2371530-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cadence have several controllers from 0x000403xx family but current
driver suuport detecting only one with DID equal 0x0004034E.
It causes that if someone uses different CDNSP controller then driver
will use incorrect version and register space.
Patch fix this issue.
cc: stable@vger.kernel.org
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20240215121609.259772-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
host.c file has some parts of code that were introduced for CDNS3 driver
and should not be used with CDNSP driver.
This patch blocks using these parts of codes by CDNSP driver.
These elements include:
- xhci_plat_cdns3_xhci object
- cdns3 specific XECP_PORT_CAP_REG register
- cdns3 specific XECP_AUX_CTRL_REG1 register
cc: stable@vger.kernel.org
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20240206104018.48272-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes relying upon linux/of_platform.h to include
linux/platform_device.h, which it no longer does, thereby fixing
compilation problems like:
In file included from drivers/usb/host/uhci-hcd.c:850:
drivers/usb/host/uhci-grlib.c: In function 'uhci_hcd_grlib_probe':
drivers/usb/host/uhci-grlib.c:92:29: error: invalid use of undefined type 'struct platform_device'
92 | struct device_node *dn = op->dev.of_node;
| ^~
Fixes: ef175b29a2 ("of: Stop circularly including of_device.h and of_platform.h")
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Link: https://lore.kernel.org/r/20240129075056.1511630-1-andreas@gaisler.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been observed that some USB/UAS devices return generic properties
hardcoded in firmware for mode pages for a period of time after a device
has been discovered. The reported properties are either garbage or they do
not accurately reflect the characteristics of the physical storage device
attached in the case of a bridge.
Prior to commit 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to
avoid calling revalidate twice") we would call revalidate several
times during device discovery. As a result, incorrect values would
eventually get replaced with ones accurately describing the attached
storage. When we did away with the redundant revalidate pass, several
cases were reported where devices reported nonsensical values or would
end up in write-protected state.
An initial attempt at addressing this issue involved introducing a
delayed second revalidate invocation. However, this approach still
left some devices reporting incorrect characteristics.
Tasos Sahanidis debugged the problem further and identified that
introducing a READ operation prior to MODE SENSE fixed the problem and that
it wasn't a timing issue. Issuing a READ appears to cause the devices to
update their state to reflect the actual properties of the storage
media. Device properties like vendor, model, and storage capacity appear to
be correctly reported from the get-go. It is unclear why these devices
defer populating the remaining characteristics.
Match the behavior of a well known commercial operating system and
trigger a READ operation prior to querying device characteristics to
force the device to populate the mode pages.
The additional READ is triggered by a flag set in the USB storage and
UAS drivers. We avoid issuing the READ for other transport classes
since some storage devices identify Linux through our particular
discovery command sequence.
Link: https://lore.kernel.org/r/20240213143306.2194237-1-martin.petersen@oracle.com
Fixes: 1e029397d1 ("scsi: sd: Reorganize DIF/DIX code to avoid calling revalidate twice")
Cc: stable@vger.kernel.org
Reported-by: Tasos Sahanidis <tasos@tasossah.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 398aa9a7e7.
The update to the gadget API to support EBC feature is incomplete. It's
missing at least the following:
* New usage documentation
* Gadget capability check
* Condition for the user to check how many and which endpoints can be
used as "fifo_mode"
* Description of how it can affect completed request (e.g. dwc3 won't
update TRB on completion -- ie. how it can affect request's actual
length report)
Let's revert this until it's ready.
Fixes: 398aa9a7e7 ("usb: dwc3: Support EBC feature of DWC_usb31")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3042f847ff904b4dd4e4cf66a1b9df470e63439e.1707441690.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids for 6.8-rc3.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZb0HUgAKCRALxc3C7H1l
CApxAP9sgKgE0sUvnzn+9/jxR+9+NGkJESBOud/ovI1c1zPIXwEAqJAU5vnfkUWI
VmMw/fTnCs5H0uiN6pbkQnZQ0JT7NgU=
=EIrL
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.8-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device ids for 6.8-rc3
Here are some new device ids for 6.8-rc3.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.8-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Fibocom FM101-GL variant
USB: serial: qcserial: add new usb-id for Dell Wireless DW5826e
USB: serial: cp210x: add ID for IMST iM871A-USB
The device IMST USB-Stick for Smart Meter is a rebranded IMST iM871A-USB
Wireless M-Bus USB-adapter. It is used to read wireless water, gas and
electricity meters.
Signed-off-by: Leonard Dallmayr <leonard.dallmayr@mailbox.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
If the PD is disabled for the port, port->pds will be left as NULL,
which causes the following crash during caps intilisation. Fix the
crash.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
tcpm_register_port+0xaec/0xc44
qcom_pmic_typec_probe+0x1a4/0x254
platform_probe+0x68/0xc0
really_probe+0x148/0x2ac
__driver_probe_device+0x78/0x12c
driver_probe_device+0xd8/0x160
Bluetooth: hci0: QCA Product ID :0x0000000a
__device_attach_driver+0xb8/0x138
bus_for_each_drv+0x80/0xdc
Bluetooth: hci0: QCA SOC Version :0x40020150
__device_attach+0x9c/0x188
device_initial_probe+0x14/0x20
bus_probe_device+0xac/0xb0
deferred_probe_work_func+0x8c/0xc8
process_one_work+0x1ec/0x51c
worker_thread+0x1ec/0x3e4
kthread+0x120/0x124
ret_from_fork+0x10/0x20
Fixes: cd099cde4e ("usb: typec: tcpm: Support multiple capabilities")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-5-182d9aa0a5b3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PPM on some Dell laptops seems to expect that the ACK_CC_CI
command to clear the connector change notification is in turn
followed by another ACK_CC_CI to acknowledge the ACK_CC_CI command
itself. This is in violation of the UCSI spec that states:
"The only notification that is not acknowledged by the OPM is
the command completion notification for the ACK_CC_CI or the
PPM_RESET command."
Add a quirk to send this ack anyway.
Apply the quirk to all Dell systems.
On the first command that acks a connector change send a dummy
command to determine if it runs into a timeout. Only activate
the quirk if it does. This ensure that we do not break Dell
systems that do not need the quirk.
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-4-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of a spurious or otherwise delayed notification it is
possible that CCI still reports the previous completion. The
UCSI spec is aware of this and provides two completion bits in
CCI, one for normal commands and one for acks. As acks and commands
alternate the notification handler can determine if the completion
bit is from the current command.
The initial UCSI code correctly handled this but the distinction
between the two completion bits was lost with the introduction of
the new API.
To fix this revive the ACK_PENDING bit for ucsi_acpi and only complete
commands if the completion bit matches.
Fixes: f56de278e8 ("usb: typec: ucsi: acpi: Move to the new API")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling ->sync_write must be done while holding the PPM lock as
the mailbox logic does not support concurrent commands.
At least since the addition of partner task this means that
ucsi_acknowledge_connector_change should be called with the
PPM lock held as it calls ->sync_write.
Thus protect the only call to ucsi_acknowledge_connector_change
with the PPM. All other calls to ->sync_write already happen
under the PPM lock.
Fixes: b9aa02ca39 ("usb: typec: ucsi: Add polling mechanism for partner tasks like alt mode checking")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ULPI per-device debugfs root is named after the ulpi device's
parent, but ulpi_unregister_interface tries to remove a debugfs
directory named after the ulpi device itself. This results in the
directory sticking around and preventing subsequent (deferred) probes
from succeeding. Change the directory name to match the ulpi device.
Fixes: bd0a0a024f ("usb: ulpi: Add debugfs support")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240126223800.2864613-1-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 1e35f07439.
Given that ERROR_RECOVERY calls into PORT_RESET for Hi-Zing
the CC pins, setting CC pins to default state during PORT_RESET
breaks error recovery.
4.5.2.2.2.1 ErrorRecovery State Requirements
The port shall not drive VBUS or VCONN, and shall present a
high-impedance to ground (above zOPEN) on its CC1 and CC2 pins.
Hi-Zing the CC pins is the inteded behavior for PORT_RESET.
CC pins are set to default state after tErrorRecovery in
PORT_RESET_WAIT_OFF.
4.5.2.2.2.2 Exiting From ErrorRecovery State
A Sink shall transition to Unattached.SNK after tErrorRecovery.
A Source shall transition to Unattached.SRC after tErrorRecovery.
Cc: stable@vger.kernel.org
Cc: Frank Wang <frank.wang@rock-chips.com>
Fixes: 1e35f07439 ("usb: typec: tcpm: fix cc role at port reset")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240117114742.2587779-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When write UDC to empty and unbind gadget driver from gadget device, it is
possible that there are many queue failures for mass storage function.
The root cause is mass storage main thread alaways try to queue request to
receive a command from host if running flag is on, on platform like dwc3,
if pull down called, it will not queue request again and return
-ESHUTDOWN, but it not affect running flag of mass storage function.
Check return code from mass storage function and clear running flag if it
is -ESHUTDOWN, also indicate start in/out transfer failure to break loops.
Cc: stable <stable@kernel.org>
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240123034829.3848409-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OTG 1.3 spec has the feature A_ALT_HNP_SUPPORT, which tells
a device that it is connected to the wrong port. Some devices
refuse to operate if you enable that feature, because it indicates
to them that they ought to request to be connected to another port.
According to the spec this feature may be used based only the following
three conditions:
6.5.3 a_alt_hnp_support
Setting this feature indicates to the B-device that it is connected to
an A-device port that is not capable of HNP, but that the A-device does
have an alternate port that is capable of HNP.
The A-device is required to set this feature under the following conditions:
• the A-device has multiple receptacles
• the A-device port that connects to the B-device does not support HNP
• the A-device has another port that does support HNP
A check for the third and first condition is missing. Add it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Fixes: 7d2d641c44 ("usb: otg: don't set a_alt_hnp_support feature for OTG 2.0 device")
Link: https://lore.kernel.org/r/20240122153545.12284-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When power is recycled in usb controller during system power management,
the controller will recognize it and switch role if role has been changed
during power lost. In current design, it will be completed in resume()
function. However, this may bring issues since usb class devices have
their pm operations too and these device's resume() functions are still
not being called at this point. When usb controller recognized host role
should be stopped, these usb class devices will be removed at this point.
But these usb class devices can't be removed in some cases, such as scsi
devices. Since scsi driver may sync data to U-disk, however it will block
there because scsi drvier can only handle pm request when is in suspended
state. Therefore, there may exist a dependency between ci_resume() and usb
class device's resume(). To break this potential dependency, we need to
handle power lost work in a workqueue.
Fixes: 74494b3321 ("usb: chipidea: core: add controller resume support when controller is powered off")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240119123537.3614838-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current scenario if Plug-out and Plug-In performed continuously
there could be a chance while checking for dwc->gadget_driver in
dwc3_gadget_suspend, a NULL pointer dereference may occur.
Call Stack:
CPU1: CPU2:
gadget_unbind_driver dwc3_suspend_common
dwc3_gadget_stop dwc3_gadget_suspend
dwc3_disconnect_gadget
CPU1 basically clears the variable and CPU2 checks the variable.
Consider CPU1 is running and right before gadget_driver is cleared
and in parallel CPU2 executes dwc3_gadget_suspend where it finds
dwc->gadget_driver which is not NULL and resumes execution and then
CPU1 completes execution. CPU2 executes dwc3_disconnect_gadget where
it checks dwc->gadget_driver is already NULL because of which the
NULL pointer deference occur.
Cc: stable@vger.kernel.org
Fixes: 9772b47a4c ("usb: dwc3: gadget: Fix suspend/resume during device mode")
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20240119094825.26530-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the function update_port_device_state gets the usb_hub from
udev->parent by calling usb_hub_to_struct_hub.
However, in case the actconfig or the maxchild is 0, the usb_hub would
be NULL and upon further accessing to get port_dev would result in null
pointer dereference.
Fix this by introducing an if check after the usb_hub is populated.
Fixes: 83cb2604f6 ("usb: core: add sysfs entry for usb device state")
Cc: stable@vger.kernel.org
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240110095814.7626-1-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI 4.9 explicitly forbids assuming that the xHC has released its
ownership of a multi-TRB TD when it reports an error on one of the
early TRBs. Yet the driver makes such assumption and releases the TD,
allowing the remaining TRBs to be freed or overwritten by new TDs.
The xHC should also report completion of the final TRB due to its IOC
flag being set by us, regardless of prior errors. This event cannot
be recognized if the TD has already been freed earlier, resulting in
"Transfer event TRB DMA ptr not part of current TD" error message.
Fix this by reusing the logic for processing isoc Transaction Errors.
This also handles hosts which fail to report the final completion.
Fix transfer length reporting on Babble errors. They may be caused by
device malfunction, no guarantee that the buffer has been filled.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last TRB of a isoc TD might not trigger an event if there was
an error event for a TRB mid TD. This is seen on a NEC Corporation
uPD720200 USB 3.0 Host
After an error mid a multi-TRB TD the xHC should according to xhci 4.9.1
generate events for passed TRBs with IOC flag set if it proceeds to the
next TD. This event is either a copy of the original error, or a
"success" transfer event.
If that event is missing then the driver and xHC host get out of sync as
the driver is still expecting a transfer event for that first TD, while
xHC host is already sending events for the next TD in the list.
This leads to
"Transfer event TRB DMA ptr not part of current TD" messages.
As a solution we tag the isoc TDs that get error events mid TD.
If an event doesn't match the first TD, then check if the tag is
set, and event points to the next TD.
In that case give back the fist TD and process the next TD normally
Make sure TD status and transferred length stay valid in both cases
with and without final TD completion event.
Reported-by: Michał Pecio <michal.pecio@gmail.com>
Closes: https://lore.kernel.org/linux-usb/20240112235205.1259f60c@foxbook/
Tested-by: Michał Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sanity check of interrupter index when adding a new interrupter is
off by one. intr_num needs to be smaller than xhci->max_interrupter to
fit the array of interrupters.
Luckily this doesn't cause any real word harm as xhci_add_interrupter()
is always called with a intr_num value smaller than xhci->max_interrupters
in any current kernel.
Should not be needed for stable as 6.7 kernel and older only supports
one interrupter, with intr_num always being zero.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-usb/e9771296-586d-456a-ac24-a82de79bb2e6@moroto.mountain/
Fixes: 4bf398e15a ("xhci: split allocate interrupter into separate alloacte and add parts")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent commit [1] added support for changing max segment size of the NCM
interface via configfs. But the value of segment size value stored in
ncm_opts need to be converted to little endian before saving it in
ecm_desc. Also while initialising the value of segment size in opts during
instance allocation, the value ETH_FRAME_LEN needs to be assigned directly
without any conversion as ETH_FRAME_LEN and the variable max_segment_size
are native endian. The current implementaion modifies it into little endian
thus breaking things for big endian targets.
Fix endianness while assigning these variables.
While at it, fix up some stray spaces in comments added in code.
[1]: https://lore.kernel.org/all/20231221153216.18657-1-quic_kriskura@quicinc.com/
Fixes: 1900daeefd ("usb: gadget: ncm: Add support to update wMaxSegmentSize via configfs")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240118154910.8765-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upstream commit bac1ec5514 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. Currently this quirk can only be set using
xhci private data. But there are some drivers like dwc3/host.c
which adds adds quirks using software node for xhci device.
Hence set this xhci quirk by iterating over device properties.
Cc: stable@vger.kernel.org # 5.11
Fixes: bac1ec5514 ("usb: xhci: Set quirk for XHCI_SG_TRB_CACHE_SIZE_QUIRK")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20240116055816.1169821-3-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upstream commit bac1ec5514 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. But the support for this quirk isn't present
in the DWC3 layer.
We will encounter this XHCI timeout/hung issue if we run iperf
loopback tests using RTL8156 ethernet adaptor on DWC3 targets
with scatter-gather enabled. This gets resolved after enabling
the XHCI_SG_TRB_CACHE_SIZE_QUIRK. This patch enables it using
the xhci device property since its needed for DWC3 controller.
In Synopsys DWC3 databook,
Table 9-3: xHCI Debug Capability Limitations
Chained TRBs greater than TRB cache size: The debug capability
driver must not create a multi-TRB TD that describes smaller
than a 1K packet that spreads across 8 or more TRBs on either
the IN TR or the OUT TR.
Cc: stable@vger.kernel.org #5.11
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240116055816.1169821-2-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaedng8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yndHACfX3SA2ipK5umpMsWOoLMCBV6VyrwAn3t+FPd/
z4mNiCuNUhbEnU7RinK0
=k/E9
-----END PGP SIGNATURE-----
Merge tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: typec: tipd: fix use of device-specific init function
usb: typec: tipd: Separate reset for TPS6598x
usb: mon: Fix atomicity violation in mon_bin_vma_fault
usb: gadget: uvc: Remove nested locking
usb: gadget: uvc: Fix use are free during STREAMOFF
usb: typec: class: fix typec_altmode_put_partner to put plugs
dt-bindings: usb: dwc3: Limit num-hc-interrupters definition
dt-bindings: usb: xhci: Add num-hc-interrupters definition
xhci: add support to allocate several interrupters
USB: core: Use device_driver directly in struct usb_driver and usb_device_driver
arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry
usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue
arm64: dts: qcom: msm8996: Remove PNoC clock from MSS
arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8939: Drop RPM bus clocks
arm64: dts: qcom: sdm630: Drop RPM bus clocks
arm64: dts: qcom: qcs404: Drop RPM bus clocks
arm64: dts: qcom: msm8996: Drop RPM bus clocks
...
new drivers:
- imagination - new driver for Imagination Technologies GPU
- xe - new driver for Intel GPUs using core drm concepts
core:
- add CLOSE_FB ioctl
- remove old UMS ioctls
- increase max objects to accomodate AMD color mgmt
encoder:
- create per-encoder debugfs directory
edid:
- split out drm_eld
- SAD helpers
- drop edid_firmware module parameter
format-helper:
- cache format conversion buffers
sched:
- move from kthread to workqueue
- rename some internals
- implement dynamic job-flow control
gpuvm:
- provide more features to handle GEM objects
client:
- don't acquire module reference
displayport:
- add mst path property documentation
fdinfo:
- alignment fix
dma-buf:
- add fence timestamp helper
- add fence deadline support
bridge:
- transparent aux-bridge for DP/USB-C
- lt8912b: add suspend/resume support and power regulator support
panel:
- edp: AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49
- chromebook panel support
- elida-kd35t133: rework pm
- powkiddy RK2023 panel
- himax-hx8394: drop prepare/unprepare and shutdown logic
- BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G
- Evervision VGG644804, SDC ATNA45AF01
- nv3052c: register docs, init sequence fixes, fascontek FS035VG158
- st7701: Anbernic RG-ARC support
- r63353 panel controller
- Ilitek ILI9805 panel controller
- AUO G156HAN04.0
simplefb:
- support memory regions
- support power domains
amdgpu:
- add new 64-bit sequence number infrastructure
- add AMD specific color management
- ACPI WBRF support for RF interference handling
- GPUVM updates
- RAS updates
- DCN 3.5 updates
- Rework PCIe link speed handling
- Document GPU reset types
- DMUB fixes
- eDP fixes
- NBIO 7.9/7.11 updates
- SubVP updates
- XGMI PCIe state dumping for aqua vanjaram
- GFX11 golden register updates
- enable tunnelling on high pri compute
amdkfd:
- Migrate TLB flushing logic to amdgpu
- Trap handler fixes
- Fix restore workers handling on suspend/resume
- Fix possible memory leak in pqm_uninit()
- support import/export of dma-bufs using GEM handles
radeon:
- fix possible overflows in command buffer checking
- check for errors in ring_lock
i915:
- reorg display code for reuse in xe driver
- fdinfo memory stats printing
- DP MST bandwidth mgmt improvements
- DP panel replay enabling
- MTL C20 phy state verification
- MTL DP DSC fractional bpp support
- Audio fastset support
- use dma_fence interfaces instead of i915_sw_fence
- Separate gem and display code
- AUX register macro refactoring
- Separate display module/device parameters
- Move display capabilities debugfs under display
- Makefile cleanups
- Register cleanups
- Move display lock inits under display/
- VLV/CHV DPIO PHY register and interface refactoring
- DSI VBT sequence refactoring
- C10/C20 PHY PLL hardware readout
- DPLL code cleanups
- Cleanup PXP plane protection checks
- Improve display debug msgs
- PSR selective fetch fixes/improvements
- DP MST fixes
- Xe2LPD FBC restrictions removed
- DGFX uses direct VBT pin mapping
- more MTL WAs
- fix MTL eDP bug
- eliminate use of kmap_atomic
habanalabs:
- sysfs entry to identify a device minor id with debugfs path
- sysfs entry to expose device module id
- add signed device info retrieval through INFO ioctl
- add Gaudi2C device support
- pcie reset prepare/done hooks
msm:
- Add support for SDM670, SM8650
- Handle the CFG interconnect to fix the obscure hangs / timeouts
- Kconfig fix for QMP dependency
- use managed allocators
- DPU: SDM670, SM8650 support
- DPU: Enable SmartDMA on SM8350 and SM8450
- DP: enable runtime PM support
- GPU: add metadata UAPI
- GPU: move devcoredumps to GPU device
- GPU: convert to drm_exec
ivpu:
- update FW API
- new debugfs file
- a new NOP job submission test mode
- improve suspend/resume
- PM improvements
- MMU PT optimizations
- firmware profile frequency support
- support for uncached buffers
- switch to gem shmem helpers
- replace kthread with threaded irqs
rockchip:
- rk3066_hdmi: convert to atomic
- vop2: support nv20 and nv30
- rk3588 support
mediatek:
- use devm_platform_ioremap_resource
- stop using iommu_present
- MT8188 VDOSYS1 display support
panfrost:
- PM improvements
- improve interrupt handling as poweroff
qaic:
- allow to run with single MSI
- support host/device time sync
- switch to persistent DRM devices
exynos:
- fix potential error pointer dereference
- fix wrong error checking
- add missing call to drm_atomic_helper_shutdown
omapdrm:
- dma-fence lockdep annotation fix
tidss:
- dma-fence lockdep annotation fix
- support for AM62A7
v3d:
- BCM2712 - rpi5 support
- fdinfo + gputop support
- uapi for CPU job handling
virtio-gpu:
- add context debug name
-----BEGIN PGP SIGNATURE-----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=nuw0
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2024-01-10' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This contains two major new drivers:
- imagination is a first driver for Imagination Technologies devices,
it only covers very specific devices, but there is hope to grow it
- xe is a reboot of the i915 GPU (shares display) side using a more
upstream focused development model, and trying to maximise code
sharing. It's not enabled for any hw by default, and will hopefully
get switched on for Intel's Lunarlake.
This also drops a bunch of the old UMS ioctls. It's been dead long
enough.
amdgpu has a bunch of new color management code that is being used in
the Steam Deck.
amdgpu also has a new ACPI WBRF interaction to help avoid radio
interference.
Otherwise it's the usual lots of changes in lots of places.
Detailed summary:
new drivers:
- imagination - new driver for Imagination Technologies GPU
- xe - new driver for Intel GPUs using core drm concepts
core:
- add CLOSE_FB ioctl
- remove old UMS ioctls
- increase max objects to accomodate AMD color mgmt
encoder:
- create per-encoder debugfs directory
edid:
- split out drm_eld
- SAD helpers
- drop edid_firmware module parameter
format-helper:
- cache format conversion buffers
sched:
- move from kthread to workqueue
- rename some internals
- implement dynamic job-flow control
gpuvm:
- provide more features to handle GEM objects
client:
- don't acquire module reference
displayport:
- add mst path property documentation
fdinfo:
- alignment fix
dma-buf:
- add fence timestamp helper
- add fence deadline support
bridge:
- transparent aux-bridge for DP/USB-C
- lt8912b: add suspend/resume support and power regulator support
panel:
- edp: AUO B116XTN02, BOE NT116WHM-N21,836X2, NV116WHM-N49
- chromebook panel support
- elida-kd35t133: rework pm
- powkiddy RK2023 panel
- himax-hx8394: drop prepare/unprepare and shutdown logic
- BOE BP101WX1-100, Powkiddy X55, Ampire AM8001280G
- Evervision VGG644804, SDC ATNA45AF01
- nv3052c: register docs, init sequence fixes, fascontek FS035VG158
- st7701: Anbernic RG-ARC support
- r63353 panel controller
- Ilitek ILI9805 panel controller
- AUO G156HAN04.0
simplefb:
- support memory regions
- support power domains
amdgpu:
- add new 64-bit sequence number infrastructure
- add AMD specific color management
- ACPI WBRF support for RF interference handling
- GPUVM updates
- RAS updates
- DCN 3.5 updates
- Rework PCIe link speed handling
- Document GPU reset types
- DMUB fixes
- eDP fixes
- NBIO 7.9/7.11 updates
- SubVP updates
- XGMI PCIe state dumping for aqua vanjaram
- GFX11 golden register updates
- enable tunnelling on high pri compute
amdkfd:
- Migrate TLB flushing logic to amdgpu
- Trap handler fixes
- Fix restore workers handling on suspend/resume
- Fix possible memory leak in pqm_uninit()
- support import/export of dma-bufs using GEM handles
radeon:
- fix possible overflows in command buffer checking
- check for errors in ring_lock
i915:
- reorg display code for reuse in xe driver
- fdinfo memory stats printing
- DP MST bandwidth mgmt improvements
- DP panel replay enabling
- MTL C20 phy state verification
- MTL DP DSC fractional bpp support
- Audio fastset support
- use dma_fence interfaces instead of i915_sw_fence
- Separate gem and display code
- AUX register macro refactoring
- Separate display module/device parameters
- Move display capabilities debugfs under display
- Makefile cleanups
- Register cleanups
- Move display lock inits under display/
- VLV/CHV DPIO PHY register and interface refactoring
- DSI VBT sequence refactoring
- C10/C20 PHY PLL hardware readout
- DPLL code cleanups
- Cleanup PXP plane protection checks
- Improve display debug msgs
- PSR selective fetch fixes/improvements
- DP MST fixes
- Xe2LPD FBC restrictions removed
- DGFX uses direct VBT pin mapping
- more MTL WAs
- fix MTL eDP bug
- eliminate use of kmap_atomic
habanalabs:
- sysfs entry to identify a device minor id with debugfs path
- sysfs entry to expose device module id
- add signed device info retrieval through INFO ioctl
- add Gaudi2C device support
- pcie reset prepare/done hooks
msm:
- Add support for SDM670, SM8650
- Handle the CFG interconnect to fix the obscure hangs / timeouts
- Kconfig fix for QMP dependency
- use managed allocators
- DPU: SDM670, SM8650 support
- DPU: Enable SmartDMA on SM8350 and SM8450
- DP: enable runtime PM support
- GPU: add metadata UAPI
- GPU: move devcoredumps to GPU device
- GPU: convert to drm_exec
ivpu:
- update FW API
- new debugfs file
- a new NOP job submission test mode
- improve suspend/resume
- PM improvements
- MMU PT optimizations
- firmware profile frequency support
- support for uncached buffers
- switch to gem shmem helpers
- replace kthread with threaded irqs
rockchip:
- rk3066_hdmi: convert to atomic
- vop2: support nv20 and nv30
- rk3588 support
mediatek:
- use devm_platform_ioremap_resource
- stop using iommu_present
- MT8188 VDOSYS1 display support
panfrost:
- PM improvements
- improve interrupt handling as poweroff
qaic:
- allow to run with single MSI
- support host/device time sync
- switch to persistent DRM devices
exynos:
- fix potential error pointer dereference
- fix wrong error checking
- add missing call to drm_atomic_helper_shutdown
omapdrm:
- dma-fence lockdep annotation fix
tidss:
- dma-fence lockdep annotation fix
- support for AM62A7
v3d:
- BCM2712 - rpi5 support
- fdinfo + gputop support
- uapi for CPU job handling
virtio-gpu:
- add context debug name"
* tag 'drm-next-2024-01-10' of git://anongit.freedesktop.org/drm/drm: (2340 commits)
drm/amd/display: Allow z8/z10 from driver
drm/amd/display: fix bandwidth validation failure on DCN 2.1
drm/amdgpu: apply the RV2 system aperture fix to RN/CZN as well
drm/amd/display: Move fixpt_from_s3132 to amdgpu_dm
drm/amd/display: Fix recent checkpatch errors in amdgpu_dm
Revert "drm/amdkfd: Relocate TBA/TMA to opposite side of VM hole"
drm/amd/display: avoid stringop-overflow warnings for dp_decide_lane_settings()
drm/amd/display: Fix power_helpers.c codestyle
drm/amd/display: Fix hdcp_log.h codestyle
drm/amd/display: Fix hdcp2_execution.c codestyle
drm/amd/display: Fix hdcp_psp.h codestyle
drm/amd/display: Fix freesync.c codestyle
drm/amd/display: Fix hdcp_psp.c codestyle
drm/amd/display: Fix hdcp1_execution.c codestyle
drm/amd/pm/smu7: fix a memleak in smu7_hwmgr_backend_init
drm/amdkfd: Fix iterator used outside loop in 'kfd_add_peer_prop()'
drm/amdgpu: Drop 'fence' check in 'to_amdgpu_amdkfd_fence()'
drm/amdkfd: Confirm list is non-empty before utilizing list_first_entry in kfd_topology.c
drm/amdgpu: Fix '*fw' from request_firmware() not released in 'amdgpu_ucode_request()'
drm/amdgpu: Fix variable 'mca_funcs' dereferenced before NULL check in 'amdgpu_mca_smu_get_mca_entry()'
...
A new drivers/cache/ subsystem is added to contain drivers for abstracting
cache flush methods on riscv and potentially others, as this is needed for
handling non-coherent DMA but several SoCs require nonstandard hardware
methods for it.
op-tee gains support for asynchronous notification with FF-A, as well
as support for a system thread for executing in secure world.
The tee, reset, bus, memory and scmi subsystems have a couple of minor
updates.
Platform specific soc driver changes include:
- Samsung Exynos gains driver support for Google GS101 (Tensor G1)
across multiple subsystems
- Qualcomm Snapdragon gains support for SM8650 and X1E along with
added features for some other SoCs
- Mediatek adds support for "Smart Voltage Scaling" on MT8186 and MT8195,
and driver support for MT8188 along with some code refactoring.
- Microchip Polarfire FPGA support for "Auto Update" of the FPGA bitstream
- Apple M1 mailbox driver is rewritten into a SoC driver
- minor updates on amlogic, mvebu, ti, zynq, imx, renesas and hisilicon
-----BEGIN PGP SIGNATURE-----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=4bKY
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"A new drivers/cache/ subsystem is added to contain drivers for
abstracting cache flush methods on riscv and potentially others, as
this is needed for handling non-coherent DMA but several SoCs require
nonstandard hardware methods for it.
op-tee gains support for asynchronous notification with FF-A, as well
as support for a system thread for executing in secure world.
The tee, reset, bus, memory and scmi subsystems have a couple of minor
updates.
Platform specific soc driver changes include:
- Samsung Exynos gains driver support for Google GS101 (Tensor G1)
across multiple subsystems
- Qualcomm Snapdragon gains support for SM8650 and X1E along with
added features for some other SoCs
- Mediatek adds support for "Smart Voltage Scaling" on MT8186 and
MT8195, and driver support for MT8188 along with some code
refactoring.
- Microchip Polarfire FPGA support for "Auto Update" of the FPGA
bitstream
- Apple M1 mailbox driver is rewritten into a SoC driver
- minor updates on amlogic, mvebu, ti, zynq, imx, renesas and
hisilicon"
* tag 'soc-drivers-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (189 commits)
memory: ti-emif-pm: Convert to platform remove callback returning void
memory: ti-aemif: Convert to platform remove callback returning void
memory: tegra210-emc: Convert to platform remove callback returning void
memory: tegra186-emc: Convert to platform remove callback returning void
memory: stm32-fmc2-ebi: Convert to platform remove callback returning void
memory: exynos5422-dmc: Convert to platform remove callback returning void
memory: renesas-rpc-if: Convert to platform remove callback returning void
memory: omap-gpmc: Convert to platform remove callback returning void
memory: mtk-smi: Convert to platform remove callback returning void
memory: jz4780-nemc: Convert to platform remove callback returning void
memory: fsl_ifc: Convert to platform remove callback returning void
memory: fsl-corenet-cf: Convert to platform remove callback returning void
memory: emif: Convert to platform remove callback returning void
memory: brcmstb_memc: Convert to platform remove callback returning void
memory: brcmstb_dpfe: Convert to platform remove callback returning void
soc: qcom: llcc: Fix LLCC_TRP_ATTR2_CFGn offset
firmware: qcom: qseecom: fix memory leaks in error paths
dt-bindings: clock: google,gs101: rename CMU_TOP gate defines
soc: qcom: llcc: Fix typo in kernel-doc
dt-bindings: soc: qcom,aoss-qmp: document the X1E80100 Always-On Subsystem side channel
...
