MicroSD card slot in the Pinebook Pro is located on a separate
daughterboard that's connected to the mainboard using a rather
long flat cable. The resulting signal degradation causes many
perfectly fine microSD cards not to work in the Pinebook Pro,
which is a common source of frustration among the owners.
Changing the mode and lowering the speed reportedly fixes this
issue and makes many microSD cards work as expected.
Co-developed-by: Dragan Simic <dragan.simic@gmail.com>
Signed-off-by: Dragan Simic <dragan.simic@gmail.com>
Tested-by: JR Gonzalez <jrg@scientiam.org>
Signed-off-by: Dan Johansen <strit@manjaro.org>
Link: https://lore.kernel.org/r/20230305104730.15849-1-strit@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Just like the Quartz64 Model B the previously stated speed of sdr-104
in soquartz is too high for the hardware to reliably communicate with
some fast SD cards.
Especially on some carrierboards.
Lower this to sd-uhs-sdr50 to fix this.
Fixes: 5859b5a9c3 ("arm64: dts: rockchip: add SoQuartz CM4IO dts")
Signed-off-by: Dan Johansen <strit@manjaro.org>
Acked-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20230304164135.28430-1-strit@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Flole observes this WARNING on occasion:
[1210423.486503] WARNING: CPU: 8 PID: 1524732 at fs/ext4/ext4_jbd2.c:75 ext4_journal_check_start+0x68/0xb0
Reported-by: <flole@flole.de>
Suggested-by: Jan Kara <jack@suse.cz>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217123
Fixes: 73da852e38 ("nfsd: use vfs_iter_read/write")
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit FE990
0x1081 composition in order to avoid bind error.
Signed-off-by: Enrico Sau <enrico.sau@gmail.com>
Link: https://lore.kernel.org/r/20230306115933.198259-1-enrico.sau@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If disk_scan_partitions() is called with 'FMODE_EXCL',
blkdev_get_by_dev() will be called without 'FMODE_EXCL', however, follow
blkdev_put() is still called with 'FMODE_EXCL', which will cause
'bd_holders' counter to leak.
Fix the problem by using the right mode for blkdev_put().
Reported-by: syzbot+2bcc0d79e548c4f62a59@syzkaller.appspotmail.com
Link: https://lore.kernel.org/lkml/f9649d501bc8c3444769418f6c26263555d9d3be.camel@linux.ibm.com/T/
Tested-by: Julian Ruess <julianr@linux.ibm.com>
Fixes: e5cfefa97b ("block: fix scan partition for exclusively open device again")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Recent firmware changes modified the curve duration from 32 to 64 bits,
which breaks volume ramps. A simple solution would be to change the
definition, but unfortunately the ASoC topology framework only supports
up to 32 bit tokens.
This patch suggests breaking the 64 bit value in low and high parts, with
only the low-part extracted from topology and high-part only zeroes. Since
the curve duration is represented in hundred of nanoseconds, we can still
represent a 400s ramp, which is just fine. The defacto ABI change has no
effect on existing users since the IPC4 firmware has not been released just
yet.
Link: https://github.com/thesofproject/linux/issues/4026
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230307110656.1816-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When an IPC error happens while setting-up a widget during the FE
hw_params phase, the existing logic will unwind all previous
configurations but will overwrite the return status. The ALSA/ASoC
logic will then proceed with the prepare and trigger phases, even
though the firmware resources are not available.
Fix by returning the initial error code and ignoring the code returned
in the UNPREPARE phase.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Chao Song <chao.song@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230307114659.4614-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit a09d82ce0a ("ASoC: SOF: Intel: hda-ctrl: remove
useless sleep")
It was a mistake to remove those delays, in light of comments in the
HDaudio spec captured in snd_hdac_bus_reset_link() that the codec
needs time for its initialization and PLL lock.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230307095412.3416-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add delay between set and wait command according to hardware programming
sequence. Also add debug log to detect error.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230307095453.3719-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmic dai index was set incorrectly to bits 5-7, when it is actually using
just the lowest 3. Fix the macro for setting the bits.
Fixes: aa84ffb721 ("ASoC: SOF: ipc4-topology: Add support for SSP/DMIC DAI's")
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
Reviewed-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230307110730.1995-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With the removal of widget setup during BE hw_params, the DAI config IPC
is never sent with the SOF_DAI_CONFIG_FLAGS_HW_PARAMS. This means that
the early bit clock feature required for certain codecs will be broken.
Fix this by saving the config flags sent during BE DAI hw_params and
reusing it when the DAI_CONFIG IPC is sent after the DAI widget is set
up. Also, free the DAI config before the widget is freed.
The DAI_CONFIG IPC sent during the sof_widget_free() does not have the
DAI index information. So, save the dai_index in the config during
hw_params and reuse it during hw_free.
For IPC4, do not clear the node ID during hw_free. It will be needed for
freeing the group_ida during unprepare.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230307114639.4553-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The logic for the ioremap is to find the resource index 3 (IRAM) and
infer the BAR address by subtracting the IRAM offset. The BAR size
defined in hardware specifications is 2MB.
The commit 5947b2726b ("ASoC: SOF: Intel: Check the bar size before
remapping") tried to find the BAR size by querying the resource length
instead of a pre-canned value, but by requesting the size for index 3
it only gets the size of the IRAM. That's obviously wrong and prevents
the probe from proceeding.
This commit attempted to fix an issue in a fuzzing/simulated
environment but created another on actual devices, so the best course
of action is to revert that change.
Reported-by: Ferry Toth <fntoth@gmail.com>
Tested-by: Ferry Toth <fntoth@gmail.com> (Intel Edison-Arduino)
Link: https://github.com/thesofproject/linux/issues/3901
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230307095341.3222-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the error paths in sof_widget_ready() to free all allocated memory
and prevent memory leaks.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230307114815.4909-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason the convention for topology names was not followed and
the name inspired by another unrelated hardware configuration. As a
result, the kernel will request a non-existent topology file.
Link: https://github.com/thesofproject/sof/pull/6878
Fixes: 2ec8b081d5 ("ASoC: Intel: soc-acpi: Add entry for sof_es8336 in ADL match table")
Cc: stable@vger.kernel.org
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230307100733.15025-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the sample rate print unit from KHz to Hz.
E.g. 48000KHz becomes 48000Hz.
Signed-off-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230307110751.2053-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The sof_ipc3_rx_msg() checks for minimum size of a new rx message but it is
missing the check for upper limit.
Corrupted or compromised firmware might be able to take advantage of this
to cause out of bounds reads outside of the message area.
Reported-by: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Curtis Malainey <curtis@malainey.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230307114917.5124-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Lenovo Yoga Book X90 is a x86 tablet which ships with Android x86
as factory OS. The Android x86 kernel fork ignores I2C devices described
in the DSDT, except for the PMIC and Audio codecs.
As usual the Lenovo Yoga Book X90's DSDT contains a bunch of extra I2C
devices which are not actually there, causing various resource conflicts.
Add an ACPI_QUIRK_SKIP_I2C_CLIENTS quirk for the Lenovo Yoga Book X90
to the acpi_quirk_skip_dmi_ids table to woraround this.
The DSDT also contains broken ACPI GPIO event handlers, disable those too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net>
The Acer Iconia One 7 B1-750 is a x86 tablet which ships with Android x86
as factory OS. The Android x86 kernel fork ignores I2C devices described
in the DSDT, except for the PMIC and Audio codecs.
As usual the Acer Iconia One 7 B1-750's DSDT contains a bunch of extra I2C
devices which are not actually there, causing various resource conflicts.
Add an ACPI_QUIRK_SKIP_I2C_CLIENTS quirk for the Acer Iconia One 7 B1-750
to the acpi_quirk_skip_dmi_ids table to woraround this.
The DSDT also contains broken ACPI GPIO event handlers, disable those too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net>
x86 ACPI boards which ship with only Android as their factory image usually
have pretty broken ACPI tables, relying on everything being hardcoded in
the factory kernel image and often disabling parts of the ACPI enumeration
kernel code to avoid the broken tables causing issues.
Part of this broken ACPI code is that sometimes these boards have _AEI
ACPI GPIO event handlers which are broken.
So far this has been dealt with in the platform/x86/x86-android-tablets.c
module, which contains various workarounds for these devices, by it calling
acpi_gpiochip_free_interrupts() on gpiochip-s with troublesome handlers to
disable the handlers.
But in some cases this is too late, if the handlers are of the edge type
then gpiolib-acpi.c's code will already have run them at boot.
This can cause issues such as GPIOs ending up as owned by "ACPI:OpRegion",
making them unavailable for drivers which actually need them.
Boards with these broken ACPI tables are already listed in
drivers/acpi/x86/utils.c for e.g. acpi_quirk_skip_i2c_client_enumeration().
Extend the quirks mechanism for a new acpi_quirk_skip_gpio_event_handlers()
helper, this re-uses the DMI-ids rather then having to duplicate the same
DMI table in gpiolib-acpi.c .
Also add the new ACPI_QUIRK_SKIP_GPIO_EVENT_HANDLERS quirk to existing
boards with troublesome ACPI gpio event handlers, so that the current
acpi_gpiochip_free_interrupts() hack can be removed from
x86-android-tablets.c .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Sometimes the system boots up with a acpi_video0 backlight interface
which doesn't work. So add Dell Vostro 15 3535 into the
video_detect_dmi_table to set it to native explicitly.
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net>
I²C peripheral devices that are connected to the controller are
represented in the Linux kernel as objects of the struct i2c_client.
Fix this in the documentation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Restore ctnetlink zero mark in events and dump, from Ivan Delalande.
2) Fix deadlock due to missing disabled bh in tproxy, from Florian Westphal.
3) Safer maximum chain load in conntrack, from Eric Dumazet.
* 'main' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: conntrack: adopt safer max chain length
netfilter: tproxy: fix deadlock due to missing BH disable
netfilter: ctnetlink: revert to dumping mark regardless of event type
====================
Link: https://lore.kernel.org/r/20230307100424.2037-1-pablo@netfilter.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Initialize shift variable in mlxplat_mlxcpld_verify_bus_topology()
to 0 to avoid the following compile error:
drivers/platform/x86/mlx-platform.c:6013
mlxplat_mlxcpld_verify_bus_topology() error: uninitialized symbol 'shift'.
Fixes: 50b823fdd3 ("platform: mellanox: mlx-platform: Move bus shift assignment out of the loop")
Cc: Vadim Pasternak <vadimp@nvidia.com>
Cc: Michael Shych <michaelsh@nvidia.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230307105842.286118-1-hdegoede@redhat.com
Add the INT347E GPIO lookup table to the board data for the Surface
Go 3. This is necessary to allow the ov7251 IR camera to probe
properly on that platform.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230302102611.314341-1-dan.scally@ideasonboard.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: ef0f62264b ("platform/x86: mlx-platform: Add physical bus number auto detection")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vadim Pasternak <vadimp@mellanox.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Gross <markgross@kernel.org>
Cc: platform-driver-x86@vger.kernel.org
Link: https://lore.kernel.org/r/20230226053953.4681-7-rdunlap@infradead.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
For NVSW_SN2201, select REGMAP_I2C instead of depending on it.
Fixes: c6acad68eb ("platform/mellanox: mlxreg-hotplug: Modify to use a regmap interface")
Fixes: 5ec4a8ace0 ("platform/mellanox: Introduce support for Mellanox register access driver")
Fixes: 62f9529b8d ("platform/mellanox: mlxreg-lc: Add initial support for Nvidia line card devices")
Fixes: 662f24826f ("platform/mellanox: Add support for new SN2201 system")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Michael Shych <michaelsh@nvidia.com>
Cc: Mark Gross <markgross@kernel.org>
Cc: Vadim Pasternak <vadimp@nvidia.com>
Cc: platform-driver-x86@vger.kernel.org
Link: https://lore.kernel.org/r/20230226053953.4681-6-rdunlap@infradead.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Fix warning:
drivers/platform/x86/intel/tpmi.c:253 tpmi_create_device()
warn: 'feature_vsec_dev' was already freed.
If there is some error, feature_vsec_dev memory is freed as part
of resource managed call intel_vsec_add_aux(). So, additional
kfree() call is not required.
Reordered res allocation and feature_vsec_dev, so that on error
only res is freed.
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/platform-driver-x86/Y%2FxYR7WGiPayZu%2FR@kili/T/#u
Fixes: 47731fd286 ("platform/x86/intel: Intel TPMI enumeration driver")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230227140614.2913474-1-srinivas.pandruvada@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
A new command CONFIG_TDP_GET_RATIO_INFO is added, with sub command type
of 0x0C. The previous range of valid sub commands was from 0x00 to 0x0B.
Change the valid range from 0x00 to 0x0C.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230227053504.2734214-1-srinivas.pandruvada@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
After using the built-in UEFI hardware diagnostics to compare
the measured battery temperature, i noticed that the temperature
is actually expressed in tenth degree kelvin, similar to the
SBS-Data standard. For example, a value of 2992 is displayed as
26 degrees celsius.
Fix the scaling so that the correct values are being displayed.
Tested on a Dell Inspiron 3505.
Fixes: a77272c160 ("platform/x86: dell: Add new dell-wmi-ddv driver")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230218115318.20662-2-W_Armin@gmx.de
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
If one or both sensor buffers could not be initialized, either
due to missing hardware support or due to some error during probing,
the resume handler will encounter undefined behaviour when
attempting to lock buffers then protected by an uninitialized or
destroyed mutex.
Fix this by introducing a "active" flag which is set during probe,
and only invalidate buffers which where flaged as "active".
Tested on a Dell Inspiron 3505.
Fixes: 3b7eeff93d ("platform/x86: dell-ddv: Add hwmon support")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230218115318.20662-1-W_Armin@gmx.de
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The amd_pmc_write_stb() function was previously hidden in an
ifdef to avoid a warning when CONFIG_SUSPEND is disabled, but
now there is an additional caller:
drivers/platform/x86/amd/pmc.c: In function 'amd_pmc_stb_debugfs_open_v2':
drivers/platform/x86/amd/pmc.c:256:8: error: implicit declaration of function 'amd_pmc_write_stb'; did you mean 'amd_pmc_read_stb'? [-Werror=implicit-function-declaration]
256 | ret = amd_pmc_write_stb(dev, AMD_PMC_STB_DUMMY_PC);
| ^~~~~~~~~~~~~~~~~
| amd_pmc_read_stb
There is now an easier way to handle this using DEFINE_SIMPLE_DEV_PM_OPS()
to replace all the #ifdefs, letting gcc drop any of the unused functions
silently.
Fixes: b0d4bb9735 ("platform/x86/amd: pmc: Write dummy postcode into the STB DRAM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230214152512.806188-1-arnd@kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Customers using GKE 1.25 and 1.26 are facing conntrack issues
root caused to commit c9c3b6811f ("netfilter: conntrack: make
max chain length random").
Even if we assume Uniform Hashing, a bucket often reachs 8 chained
items while the load factor of the hash table is smaller than 0.5
With a limit of 16, we reach load factors of 3.
With a limit of 32, we reach load factors of 11.
With a limit of 40, we reach load factors of 15.
With a limit of 50, we reach load factors of 24.
This patch changes MIN_CHAINLEN to 50, to minimize risks.
Ideally, we could in the future add a cushion based on expected
load factor (2 * nf_conntrack_max / nf_conntrack_buckets),
because some setups might expect unusual values.
Fixes: c9c3b6811f ("netfilter: conntrack: make max chain length random")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZAZZ1wAKCRDbK58LschI
g4fcAQDYVsICeBDmhdBdZs7Kb91/s6SrU6B0jy4zs0gOIBBOhgD7B3jt3dMTD2tp
rPLHlv6uUoYS7mbZsrZi/XjVw8UmewM=
=VUnr
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-03-06
We've added 8 non-merge commits during the last 7 day(s) which contain
a total of 9 files changed, 64 insertions(+), 18 deletions(-).
The main changes are:
1) Fix BTF resolver for DATASEC sections when a VAR points at a modifier,
that is, keep resolving such instances instead of bailing out,
from Lorenz Bauer.
2) Fix BPF test framework with regards to xdp_frame info misplacement
in the "live packet" code, from Alexander Lobakin.
3) Fix an infinite loop in BPF sockmap code for TCP/UDP/AF_UNIX,
from Liu Jian.
4) Fix a build error for riscv BPF JIT under PERF_EVENTS=n,
from Randy Dunlap.
5) Several BPF doc fixes with either broken links or external instead
of internal doc links, from Bagas Sanjaya.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: check that modifier resolves after pointer
btf: fix resolving BTF_KIND_VAR after ARRAY, STRUCT, UNION, PTR
bpf, test_run: fix &xdp_frame misplacement for LIVE_FRAMES
bpf, doc: Link to submitting-patches.rst for general patch submission info
bpf, doc: Do not link to docs.kernel.org for kselftest link
bpf, sockmap: Fix an infinite loop error when len is 0 in tcp_bpf_recvmsg_parser()
riscv, bpf: Fix patch_text implicit declaration
bpf, docs: Fix link to BTF doc
====================
Link: https://lore.kernel.org/r/20230306215944.11981-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the controller is not marked as cache coherent, then kernel will
try to ensure coherency during dma-ops and that may cause data corruption.
So, mark the PCIe node as dma-coherent as the devices on PCIe bus are
cache coherent.
Cc: stable@vger.kernel.org
Fixes: 92e0ee9f83 ("arm64: dts: qcom: sc7280: Add PCIe and PHY related node")
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1677584952-17496-1-git-send-email-quic_krichai@quicinc.com
The previous commit mistakenly introduced sim_ctrl_default as pinctrl,
this is incorrect, the interface for sim card selection varies between
different devices and should not be placed in the dtsi.
This commit selects external SIM card slot for ufi001c as default.
uf896 selects the correct SIM card slot automatically, thus does not need
this pinctrl node.
Fixes: faf6943146 ("arm64: dts: qcom: msm8916-thwc: Add initial device trees")
Signed-off-by: Yang Xiwen <forbidden405@foxmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/tencent_7036BCA256055D05F8C49D86DF7F0E2D1A05@qq.com
Older platforms don't have qcom,vmid set, handle -EINVAL return value
correctly. And since num_vmids is passed to of_property_read_u32_array
later we should make sure it has a sane value before continuing.
Fixes: e656cd0bcf ("soc: qcom: rmtfs: Optionally map RMTFS to more VMs")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230305-rmtfs-vmid-fix-v1-2-6a7206081602@z3ntu.xyz
of_property_count_u32_elems returns a negative integer when an error
happens , but since the value was assigned to an unsigned integer, the
check never worked correctly. Also print the correct variable in the
error print, ret isn't used here.
Fixes: e656cd0bcf ("soc: qcom: rmtfs: Optionally map RMTFS to more VMs")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230305-rmtfs-vmid-fix-v1-1-6a7206081602@z3ntu.xyz
The slice IDs for CVPFW, CPUSS1 and CPUWHT currently overflow the 32bit
LLCC config registers, which means it is writing beyond the upper limit
of the ATTR0_CFGn and ATTR1_CFGn range of registers. But the most obvious
impact is the fact that the mentioned slices do not get configured at all,
which will result in reduced performance. Fix that by using the slice ID
values taken from the latest LLCC SC table.
Fixes: ec69dfbdc4 ("soc: qcom: llcc: Add sc8180x and sc8280xp configurations")
Cc: stable@vger.kernel.org # 5.19+
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Juerg Haefliger <juerg.haefliger@canonical.com>
Reviewed-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230306135527.509796-1-abel.vesa@linaro.org
My randconfig build setup ran into another kallsyms warning:
Inconsistent kallsyms data
Try make KALLSYMS_EXTRA_PASS=1 as a workaround
After adding some debugging code to kallsyms.c, I saw that the recently
added kallsyms_seqs_of_names symbol can sometimes cause the second stage
table to be slightly longer than the first stage, which makes the
build inconsistent.
Add it to the exception table that contains all other kallsyms-generated
symbols.
Fixes: 60443c88f3 ("kallsyms: Improve the performance of kallsyms_lookup_name()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
