Michael Chan says:
====================
bnxt_en: Misc. bug fixes
This series fixes a bug in the driver initialization path, MSIX
setup sequencing issue in the FW error and AER paths, a missing
skb_mark_for_recycle() in the VLAN error path, some ethtool coredump
fixes, an ethtool selftest fix, and an ethtool register dump byte order
fix.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For version 1 register dump that includes the PCIe stats, the existing
code incorrectly assumes that all PCIe stats are 64-bit values. Fix it
by using an array containing the starting and ending index of the 32-bit
values. The loop in bnxt_get_regs() will use the array to do proper
endian swap for the 32-bit values.
Fixes: b5d600b027 ("bnxt_en: Add support for 'ethtool -d'")
Reviewed-by: Shruti Parab <shruti.parab@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When retrieving the FW coredump using ethtool, it can sometimes cause
memory corruption:
BUG: KFENCE: memory corruption in __bnxt_get_coredump+0x3ef/0x670 [bnxt_en]
Corrupted memory at 0x000000008f0f30e8 [ ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ] (in kfence-#45):
__bnxt_get_coredump+0x3ef/0x670 [bnxt_en]
ethtool_get_dump_data+0xdc/0x1a0
__dev_ethtool+0xa1e/0x1af0
dev_ethtool+0xa8/0x170
dev_ioctl+0x1b5/0x580
sock_do_ioctl+0xab/0xf0
sock_ioctl+0x1ce/0x2e0
__x64_sys_ioctl+0x87/0xc0
do_syscall_64+0x5c/0xf0
entry_SYSCALL_64_after_hwframe+0x78/0x80
...
This happens when copying the coredump segment list in
bnxt_hwrm_dbg_dma_data() with the HWRM_DBG_COREDUMP_LIST FW command.
The info->dest_buf buffer is allocated based on the number of coredump
segments returned by the FW. The segment list is then DMA'ed by
the FW and the length of the DMA is returned by FW. The driver then
copies this DMA'ed segment list to info->dest_buf.
In some cases, this DMA length may exceed the info->dest_buf length
and cause the above BUG condition. Fix it by capping the copy
length to not exceed the length of info->dest_buf. The extra
DMA data contains no useful information.
This code path is shared for the HWRM_DBG_COREDUMP_LIST and the
HWRM_DBG_COREDUMP_RETRIEVE FW commands. The buffering is different
for these 2 FW commands. To simplify the logic, we need to move
the line to adjust the buffer length for HWRM_DBG_COREDUMP_RETRIEVE
up, so that the new check to cap the copy length will work for both
commands.
Fixes: c74751f4c3 ("bnxt_en: Return error if FW returns more data than dump length")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Shruti Parab <shruti.parab@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling HWRM_DBG_COREDUMP_LIST FW command in
bnxt_hwrm_dbg_dma_data(), the allocated buffer info->dest_buf is
not freed in the error path. In the normal path, info->dest_buf
is assigned to coredump->data and it will eventually be freed after
the coredump is collected.
Free info->dest_buf immediately inside bnxt_hwrm_dbg_dma_data() in
the error path.
Fixes: c74751f4c3 ("bnxt_en: Return error if FW returns more data than dump length")
Reported-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Shruti Parab <shruti.parab@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is similar to the last patch to delay the
pci_alloc_irq_vectors() call in the AER path until after calling
bnxt_reserve_rings(). bnxt_reserve_rings() needs to properly map
the MSIX table first before we call pci_alloc_irq_vectors() which
may immediately write to the MSIX table in some architectures.
Move the bnxt_init_int_mode() call from bnxt_io_slot_reset() to
bnxt_io_resume() after calling bnxt_reserve_rings().
With this change, the AER path may call bnxt_open() ->
bnxt_hwrm_if_change() with bp->irq_tbl set to NULL. bp->irq_tbl is
cleared when we call bnxt_clear_int_mode() in bnxt_io_slot_reset().
So we cannot use !bp->irq_tbl to detect aborted FW reset. Add a
new BNXT_FW_RESET_STATE_ABORT to detect aborted FW reset in
bnxt_hwrm_if_change().
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some architectures (e.g. ARM), calling pci_alloc_irq_vectors()
will immediately cause the MSIX table to be written. This will not
work if we haven't called bnxt_reserve_rings() to properly map
the MSIX table to the MSIX vectors reserved by FW.
Fix the FW error recovery path to delay the bnxt_init_int_mode() ->
pci_alloc_irq_vectors() call by removing it from bnxt_hwrm_if_change().
bnxt_request_irq() later in the code path will call it and by then the
MSIX table is properly mapped.
Fixes: 4343838ca5 ("bnxt_en: Replace deprecated PCI MSIX APIs")
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bnxt_rx_vlan() fails because the VLAN protocol ID is invalid,
the SKB is freed but we're missing the call to recycle it. This
may cause the warning:
"page_pool_release_retry() stalled pool shutdown"
Add the missing skb_mark_for_recycle() in bnxt_rx_vlan().
Fixes: 86b05508f7 ("bnxt_en: Use the unified RX page pool buffers for XDP and non-XDP")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RDMA driver is loaded, running offline self test is not
supported and driver returns failure early. But it is not clearing
the input buffer and hence the application prints some junk
characters for individual test results.
Fix it by clearing the buffer before returning.
Fixes: 895621f1c8 ("bnxt_en: Don't support offline self test when RoCE driver is loaded")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WARN_ON() is triggered in __flush_work() if bnxt_init_chip() fails
because we call cancel_work_sync() on dim work that has not been
initialized.
WARNING: CPU: 37 PID: 5223 at kernel/workqueue.c:4201 __flush_work.isra.0+0x212/0x230
The driver relies on the BNXT_STATE_NAPI_DISABLED bit to check if dim
work has already been cancelled. But in the bnxt_open() path,
BNXT_STATE_NAPI_DISABLED is not set and this causes the error
path to think that it needs to cancel the uninitalized dim work.
Fix it by setting BNXT_STATE_NAPI_DISABLED during initialization.
The bit will be cleared when we enable NAPI and initialize dim work.
Fixes: 40452969a5 ("bnxt_en: Fix DIM shutdown")
Suggested-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Shravya KN <shravya.k-n@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When generating the MSR_IA32_PEBS_ENABLE value that will be loaded on
VM-Entry to a KVM guest, mask the value with the vCPU's desired PEBS_ENABLE
value. Consulting only the host kernel's host vs. guest masks results in
running the guest with PEBS enabled even when the guest doesn't want to use
PEBS. Because KVM uses perf events to proxy the guest virtual PMU, simply
looking at exclude_host can't differentiate between events created by host
userspace, and events created by KVM on behalf of the guest.
Running the guest with PEBS unexpectedly enabled typically manifests as
crashes due to a near-infinite stream of #PFs. E.g. if the guest hasn't
written MSR_IA32_DS_AREA, the CPU will hit page faults on address '0' when
trying to record PEBS events.
The issue is most easily reproduced by running `perf kvm top` from before
commit 7b100989b4 ("perf evlist: Remove __evlist__add_default") (after
which, `perf kvm top` effectively stopped using PEBS). The userspace side
of perf creates a guest-only PEBS event, which intel_guest_get_msrs()
misconstrues a guest-*owned* PEBS event.
Arguably, this is a userspace bug, as enabling PEBS on guest-only events
simply cannot work, and userspace can kill VMs in many other ways (there
is no danger to the host). However, even if this is considered to be bad
userspace behavior, there's zero downside to perf/KVM restricting PEBS to
guest-owned events.
Note, commit 854250329c ("KVM: x86/pmu: Disable guest PEBS temporarily
in two rare situations") fixed the case where host userspace is profiling
KVM *and* userspace, but missed the case where userspace is profiling only
KVM.
Fixes: c59a1f106f ("KVM: x86/pmu: Add IA32_PEBS_ENABLE MSR emulation for extended PEBS")
Closes: https://lore.kernel.org/all/Z_VUswFkWiTYI0eD@do-x1carbon
Reported-by: Seth Forshee <sforshee@kernel.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Tested-by: "Seth Forshee (DigitalOcean)" <sforshee@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250426001355.1026530-1-seanjc@google.com
A few ASUS models use the ALC256_FIXUP_ASUS_HEADSET_MODE although they
have no built-in mic pin on NID 0x13, as found in the commit
c1732ede5e ("ALSA: hda/realtek - Fix headset and mic on several Asus
laptops with ALC256"). This was relatively harmless in the past as
NID 0x13 was assigned as the secondary mic. But since the fix for the
pin sort order, this pin became the primary one, hence user started
noticing the broken input, and we've fixed already for a few ASUS
models to switch to ALC256_FIXUP_ASUS_MIC_NO_PRESENCE.
This patch corrects the other ASUS models to use the right quirk entry
for fixing the built-in mic regression. Here we cover X541SA
(1043:12e0), X541UV (1043:12f0), Z550SA (1043:13bf0) and X555UB
(1043:1ccd).
Fixes: 3b4309546b ("ALSA: hda: Fix headset detection failure due to unstable sort")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220058
Link: https://patch.msgid.link/20250430053210.31776-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The precomputed value for the NAND_READ_LOCATION_2 register should be
stored in 'snandc->regs->read_location2'.
Fix the qcom_spi_set_read_loc_first() function accordingly.
Fixes: 7304d19090 ("spi: spi-qpic: add driver for QCOM SPI NAND flash Interface")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Link: https://patch.msgid.link/20250428-qpic-snand-readloc2-fix-v1-1-50ce0877ff72@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Depending on the architecture __ffs() returns either an 'unsigned long'
or 'unsigned int' result. Compile-testing this driver on targets that
use the latter produces a warning:
sound/soc/intel/catpt/dsp.c: In function 'catpt_dsp_set_srampge':
sound/soc/intel/catpt/dsp.c:181:44: error: format '%ld' expects argument of type 'long int', but argument 4 has type 'u32' {aka 'unsigned int'} [-Werror=format=]
181 | dev_dbg(cdev->dev, "sanitize block %ld: off 0x%08x\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Change the type of the local variable to match the format string and
avoid the warning on any architecture.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20250429073545.3558494-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If any address or port is changed, update it in all packets and recalculate
checksum.
Fixes: 9fd1ff5d2a ("udp: Support UDP fraglist GRO/GSO.")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250426153210.14044-1-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
Fix Felix DSA taprio gates after clock jump
Richie Pearn presented a reproducible situation where traffic would get
blocked on the NXP LS1028A switch if a certain taprio schedule was
applied, and stepping the PTP clock would take place. The latter event
is an expected initial occurrence, but also at runtime, for example when
transitioning from one grandmaster to another.
The issue is completely described in patch 1/4, which also contains
the fix, but it has left me with some doubts regarding the need for
vsc9959_tas_clock_adjust() in general.
In order to prove to myself that vsc9959_tas_clock_adjust() is needed in
general, I have written a selftest for the tc-taprio data path in patch
4/4. On the LS1028A, we can clearly see the following failures without
that function:
INFO: Forcing a backward clock jump
TEST: ping [FAIL]
INFO: Setting up taprio after PTP
TEST: In band with gate [FAIL]
Reception of 100 packets failed
TEST: Out of band with gate [FAIL]
Reception of 100 packets failed
As for testing my fix from patch 1/4, that was quite a bit more complex
to do automatically. In fact, I couldn't find any other schedule that
would fail to be updated by vsc9959_tas_clock_adjust() as cleanly as
the schedule from Richie, so I've added that specific schedule as the
test_clock_jump_backward() test.
The test ordering is also (unfortunately) very strategic. Running the
selftest to the end dirties the GCL RAM, and when running
test_clock_jump_backward() once again, the GCL entries won't be all
zeroes as they were the first time around. They will contain bits and
pieces of old schedules, making it very challenging to make it fail.
Thus, test_clock_jump_backward() is the first in the test suite, and
without patch 1/4, it is only supposed to fail the _first_ time when
running after a clean boot.
====================
Link: https://patch.msgid.link/20250426144859.3128352-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a forwarding path test for tc-taprio, based on isochron. This is
specifically intended for NICs with an offloaded data path (switchdev/DSA)
and requires taprio 'flags 2'. Also, $h1 and $h2 must support hardware
timestamping, and $h1 tc-etf offload, for isochron to work.
Packets received by a switch while the egress port has a taprio schedule
with an open gate for the traffic class must be sent right away.
Packets received by the switch while the traffic class gate must be
delayed until it opens.
Packets received by the switch must be dropped if the gate for the
traffic class never opens.
Packets should pass if the maximum SDU for the traffic class allows it,
and should be dropped otherwise.
The schedule should auto-update itself if clock jumps take place while
taprio is installed. Repeat most of the above tests after forcing two
clock jumps, one backwards (in Jan 1970) and one back into the present.
Symlink it from tools/testing/selftests/drivers/net/dsa, because usually
DSA ports have the same MAC address, and we need STABLE_MAC_ADDRS=yes
from its forwarding.config for the test to run successfully.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250426144859.3128352-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make out-of-band testing (send a packet when its traffic class gate is
closed, expecting it to be delayed) more predictable by allowing the
window size to be customized by isochron_do().
From man isochron-send, the window size alters the advance time (the
delta between the transmission time of the packet, and its expected TX
time when using SO_TXTIME or tc-taprio on the sender). In absence of the
argument, isochron-send defaults to maximizing the advance time (making
it equal to the cycle length).
The default behavior is exactly what is problematic. An advance time
that is too large will make packets intended to be out-of-band still be
potentially in-band with an open gate from the schedule's previous cycle.
We need to allow that advance time to be reduced.
Perhaps a bit confusingly, isochron_do() has a shift_time argument
currently, but that does not help here. The shift time shifts both the
user space wakeup time and the expected TX time by equal amounts, it is
unable of bringing them closer to one another.
Set the window size properly for the Ocelot PSFP selftest as well.
That used to work due to a very carefully chosen SHIFT_TIME_NS.
I've re-tested that the test still works properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250426144859.3128352-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This snippet will be necessary for a future isochron-based test, so
provide a simpler high-level interface for counting the received
packets.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250426144859.3128352-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simplest setup to reproduce the issue: connect 2 ports of the
LS1028A-RDB together (eno0 with swp0) and run:
$ ip link set eno0 up && ip link set swp0 up
$ tc qdisc replace dev swp0 parent root handle 100 taprio num_tc 8 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 map 0 1 2 3 4 5 6 7 \
base-time 0 sched-entry S 20 300000 sched-entry S 10 200000 \
sched-entry S 20 300000 sched-entry S 48 200000 \
sched-entry S 20 300000 sched-entry S 83 200000 \
sched-entry S 40 300000 sched-entry S 00 200000 flags 2
$ ptp4l -i eno0 -f /etc/linuxptp/configs/gPTP.cfg -m &
$ ptp4l -i swp0 -f /etc/linuxptp/configs/gPTP.cfg -m
One will observe that the PTP state machine on swp0 starts
synchronizing, then it attempts to do a clock step, and after that, it
never fails to recover from the condition below.
ptp4l[82.427]: selected best master clock 00049f.fffe.05f627
ptp4l[82.428]: port 1 (swp0): MASTER to UNCALIBRATED on RS_SLAVE
ptp4l[83.252]: port 1 (swp0): UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[83.886]: rms 4537731277 max 9075462553 freq -18518 +/- 11467 delay 818 +/- 0
ptp4l[84.170]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[85.304]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[85.305]: port 1 (swp0): send peer delay response failed
ptp4l[85.306]: port 1 (swp0): clearing fault immediately
ptp4l[86.304]: timed out while polling for tx timestamp
A hint is given by the non-zero statistics for dropped packets which
were expecting hardware TX timestamps:
$ ethtool --include-statistics -T swp0
(...)
Statistics:
tx_pkts: 30
tx_lost: 11
tx_err: 0
We know that when PTP clock stepping takes place (from ocelot_ptp_settime64()
or from ocelot_ptp_adjtime()), vsc9959_tas_clock_adjust() is called.
Another interesting hint is that placing an early return in
vsc9959_tas_clock_adjust(), so as to neutralize this function, fixes the
issue and TX timestamps are no longer dropped.
The debugging function written by me and included below is intended to
read the GCL RAM, after the admin schedule became operational, through
the two status registers available for this purpose:
QSYS_GCL_STATUS_REG_1 and QSYS_GCL_STATUS_REG_2.
static void vsc9959_print_tas_gcl(struct ocelot *ocelot)
{
u32 val, list_length, interval, gate_state;
int i, err;
err = read_poll_timeout(ocelot_read, val,
!(val & QSYS_PARAM_STATUS_REG_8_CONFIG_PENDING),
10, 100000, false, ocelot, QSYS_PARAM_STATUS_REG_8);
if (err) {
dev_err(ocelot->dev,
"Failed to wait for TAS config pending bit to clear: %pe\n",
ERR_PTR(err));
return;
}
val = ocelot_read(ocelot, QSYS_PARAM_STATUS_REG_3);
list_length = QSYS_PARAM_STATUS_REG_3_LIST_LENGTH_X(val);
dev_info(ocelot->dev, "GCL length: %u\n", list_length);
for (i = 0; i < list_length; i++) {
ocelot_rmw(ocelot,
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM(i),
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM_M,
QSYS_GCL_STATUS_REG_1);
interval = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_2);
val = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_1);
gate_state = QSYS_GCL_STATUS_REG_1_GATE_STATE_X(val);
dev_info(ocelot->dev, "GCL entry %d: states 0x%x interval %u\n",
i, gate_state, interval);
}
}
Calling it from two places: after the initial QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
performed by vsc9959_qos_port_tas_set(), and after the one done by
vsc9959_tas_clock_adjust(), I notice the following difference.
From the tc-taprio process context, where the schedule was initially
configured, the GCL looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 1: states 0x10 interval 200000
mscc_felix 0000:00:00.5: GCL entry 2: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 3: states 0x48 interval 200000
mscc_felix 0000:00:00.5: GCL entry 4: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 5: states 0x83 interval 200000
mscc_felix 0000:00:00.5: GCL entry 6: states 0x40 interval 300000
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 200000
But from the ptp4l clock stepping process context, when the
vsc9959_tas_clock_adjust() hook is called, the GCL RAM of the
operational schedule now looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 1: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 2: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 3: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 4: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 5: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 6: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 0
I do not have a formal explanation, just experimental conclusions.
It appears that after triggering QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
for a port's TAS, the GCL entry RAM is updated anyway, despite what the
documentation claims: "Specify the time interval in
QSYS::GCL_CFG_REG_2.TIME_INTERVAL. This triggers the actual RAM
write with the gate state and the time interval for the entry number
specified". We don't touch that register (through vsc9959_tas_gcl_set())
from vsc9959_tas_clock_adjust(), yet the GCL RAM is updated anyway.
It seems to be updated with effectively stale memory, which in my
testing can hold a variety of things, including even pieces of the
previously applied schedule, for particular schedule lengths.
As such, in most circumstances it is very difficult to pinpoint this
issue, because the newly updated schedule would "behave strangely",
but ultimately might still pass traffic to some extent, due to some
gate entries still being present in the stale GCL entry RAM. It is easy
to miss.
With the particular schedule given at the beginning, the GCL RAM
"happens" to be reproducibly rewritten with all zeroes, and this is
consistent with what we see: when the time-aware shaper has gate entries
with all gates closed, traffic is dropped on TX, no wonder we can't
retrieve TX timestamps.
Rewriting the GCL entry RAM when reapplying the new base time fixes the
observed issue.
Fixes: 8670dc33f4 ("net: dsa: felix: update base time of time-aware shaper when adjusting PTP time")
Reported-by: Richie Pearn <richard.pearn@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250426144859.3128352-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the mtk_poll_rx() function detects the MTK_RESETTING flag, it will
jump to release_desc and refill the high word of the SDP on the 4GB RFB.
Subsequently, mtk_rx_clean will process an incorrect SDP, leading to a
panic.
Add patch from MediaTek's SDK to resolve this.
Fixes: 2d75891ebc ("net: ethernet: mtk_eth_soc: support 36-bit DMA addressing on MT7988")
Link: 71f47ea785
Signed-off-by: Chad Monroe <chad@monroe.io>
Link: https://patch.msgid.link/4adc2aaeb0fb1b9cdc56bf21cf8e7fa328daa345.1745715843.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 1a931c4f5e ("igc: add lock preventing multiple simultaneous PTM
transactions") added a new mutex to protect concurrent PTM transactions.
This lock is acquired in igc_ptp_reset() in order to ensure the PTM
registers are properly disabled after a device reset.
The flow where the lock is acquired already holds a spinlock, so acquiring
a mutex leads to a sleep-while-locking bug, reported both by smatch,
and the kernel test robot.
The critical section in igc_ptp_reset() does correctly use the
readx_poll_timeout_atomic variants, but the standard PTM flow uses regular
sleeping variants. This makes converting the mutex to a spinlock a bit
tricky.
Instead, re-order the locking in igc_ptp_reset. Acquire the mutex first,
and then the tmreg_lock spinlock. This is safe because there is no other
ordering dependency on these locks, as this is the only place where both
locks were acquired simultaneously. Indeed, any other flow acquiring locks
in that order would be wrong regardless.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Fixes: 1a931c4f5e ("igc: add lock preventing multiple simultaneous PTM transactions")
Link: https://lore.kernel.org/intel-wired-lan/Z_-P-Hc1yxcw0lTB@stanley.mountain/
Link: https://lore.kernel.org/intel-wired-lan/202504211511.f7738f5d-lkp@intel.com/T/#u
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Before the referenced commit, the shutdown just called idpf_remove(),
this way IDPF_REMOVE_IN_PROG was protecting us from the serv_task
rescheduling reset. Without this flag set the shutdown process is
vulnerable to HW reset or any other triggering conditions (such as
default mailbox being destroyed).
When one of conditions checked in idpf_service_task becomes true,
vc_event_task can be rescheduled during shutdown, this leads to accessing
freed memory e.g. idpf_req_rel_vector_indexes() trying to read
vport->q_vector_idxs. This in turn causes the system to become defunct
during e.g. systemctl kexec.
Considering using IDPF_REMOVE_IN_PROG would lead to more heavy shutdown
process, instead just cancel the serv_task before cancelling
adapter->serv_task before cancelling adapter->vc_event_task to ensure that
reset will not be scheduled while we are doing a shutdown.
Fixes: 4c9106f490 ("idpf: fix adapter NULL pointer dereference on reboot")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In case of failing on rss_data->rss_key allocation the function is
freeing vport without freeing earlier allocated q_vector_idxs. Fix it.
Move from freeing in error branch to goto scheme.
Fixes: d4d5587182 ("idpf: initialize interrupts and enable vport")
Reviewed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Suggested-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When libperf is built alone in-source, $(OUTPUT) isn't set. This causes
the generated uapi path to resolve to '/../arch' which results in a
permissions error:
mkdir: cannot create directory '/../arch': Permission denied
Fix it by removing the preceding '/..' which means that it gets
generated either in the tools/lib/perf part of the tree or the OUTPUT
folder. Some other rules that rely on OUTPUT further refine this
conditionally depending on whether it's an in-source or out-of-source
build, but I don't think we need the extra complexity here. And this
rule is slightly different to others because the header is needed by
both libperf and Perf. This is further complicated by the fact that Perf
always passes O=... to libperf even for in source builds, meaning that
OUTPUT isn't set consistently between projects.
Because we're no longer going one level up to try to generate the file
in the tools/ folder, Perf's include rule needs to descend into libperf.
Also fix the clean rule while we're here.
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Closes: https://lore.kernel.org/linux-perf-users/7703f88e-ccb7-4c98-9da4-8aad224e780f@leemhuis.info/
Fixes: bfb713ea53 ("perf tools: Fix arm64 build by generating unistd_64.h")
Signed-off-by: James Clark <james.clark@linaro.org>
Tested-by: Thorsten Leemhuis <linux@leemhuis.info>
Link: https://lore.kernel.org/r/20250429-james-perf-fix-libperf-in-source-build-v1-1-a1a827ac15e5@linaro.org
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
This bit is necessary to receive packets from the internal PHY.
Without this bit set, no activity occurs on the interface.
Normally u-boot sets this bit, but if u-boot is compiled without
net support, the interface will be up but without any activity.
If bit is set once, it will work until the IP is powered down or reset.
The vendor SDK sets this bit along with the PHY_ID bits.
Signed-off-by: Da Xue <da@libre.computer>
Fixes: 9a24e1ff43 ("net: mdio: add amlogic gxl mdio mux support")
Link: https://patch.msgid.link/20250425192009.1439508-1-da@libre.computer
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As it's name suggests, parse_eeprom() parses EEPROM data.
This is done by reading data, 16 bits at a time as follows:
for (i = 0; i < 128; i++)
((__le16 *) sromdata)[i] = cpu_to_le16(read_eeprom(np, i));
sromdata is at the same memory location as psrom.
And the type of psrom is a pointer to struct t_SROM.
As can be seen in the loop above, data is stored in sromdata, and thus psrom,
as 16-bit little-endian values.
However, the integer fields of t_SROM are host byte order integers.
And in the case of led_mode this leads to a little endian value
being incorrectly treated as host byte order.
Looking at rio_set_led_mode, this does appear to be a bug as that code
masks led_mode with 0x1, 0x2 and 0x8. Logic that would be effected by a
reversed byte order.
This problem would only manifest on big endian hosts.
Found by inspection while investigating a sparse warning
regarding the crc field of t_SROM.
I believe that warning is a false positive. And although I plan
to send a follow-up to use little-endian types for other the integer
fields of PSROM_t I do not believe that will involve any bug fixes.
Compile tested only.
Fixes: c3f45d322c ("dl2k: Add support for IP1000A-based cards")
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250425-dlink-led-mode-v1-1-6bae3c36e736@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MIDI substream name string is constructed from the combination of
the card shortname (which is taken from USB iProduct) and the USB
iJack. The problem is that some devices put the product name to the
iJack field, too. For example, aplaymidi -l output on the Lanchkey MK
49 are like:
% aplaymidi -l
Port Client name Port name
44:0 Launchkey MK4 49 Launchkey MK4 49 Launchkey MK4
44:1 Launchkey MK4 49 Launchkey MK4 49 Launchkey MK4
where the actual iJack name can't be seen because it's truncated due
to the doubly words.
For resolving those situations, this patch compares the iJack string
with the card shortname, and drops if both start with the same words.
Then the result becomes like:
% aplaymidi -l
Port Client name Port name
40:0 Launchkey MK4 49 Launchkey MK4 49 MIDI In
40:1 Launchkey MK4 49 Launchkey MK4 49 DAW In
A caveat is that there are some pre-defined names for certain
devices in the driver code, and this workaround shouldn't be applied
to them. Similarly, when the iJack isn't specified, we should skip
this check, too. The patch added those checks in addition to the
string comparison.
Suggested-by: Paul Davis <paul@linuxaudiosystems.com>
Tested-by: Paul Davis <paul@linuxaudiosystems.com>
Link: https://lore.kernel.org/CAFa_cKmEDQWcJatbYWi6A58Zg4Ma9_6Nr3k5LhqwyxC-P_kXtw@mail.gmail.com
Link: https://patch.msgid.link/20250429183626.20773-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEq1nRK9aeMoq1VSgcnJ2qBz9kQNkFAmgREt8ACgkQnJ2qBz9k
QNkYgggAshgJV9OieA91SMXAZgExns4oDPCKj2yuEDcX0hvYEBpHXo+Rp0QNgRav
G3mT4eSvK6oWxSnWyijsmWp+BQxrBEa/M5LIsSv5qcmuOmiJliCnKXEdbhiHl9n+
D429k2+H6ajlwtaty4XnPpVEUYnBNAHxEwYZGRP7zJWET1KFfAcemUogzoWqqh/9
AN17J/F4v6H92th3qP6AlDAyoAeEIsdKDzX6EI2ZPnj/UdYXJKvCJsUQS5LfatrY
NHmoYooBpdjpuD8r1QlOnxUsgUDinOrVdTrPKWfI711zeP6kMCFgFzZeJhNR/lTL
88G18ZDpjy6lEI4a248+QHpV+a8IVg==
=OJXd
-----END PGP SIGNATURE-----
Merge tag 'fsnotify_for_v6.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull fsnotify fix from Jan Kara:
"A fix for the recently merged mount notification support"
* tag 'fsnotify_for_v6.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
selftests/fs/mount-notify: test also remove/flush of mntns marks
fanotify: fix flush of mntns marks
Fixes and new HW support
- amd/pmc: Require at least 2.5 seconds between HW sleep cycles
- alienware-wmi-wmax:
- Add support for Alienware m15 R7
- Fix error handling to avoid uninitialized variable
- asus-wmi: Disable OOBE state also on resume
- ideapad-laptop: Support a few new buttons
- intel/hid: Add Panther Lake support
- intel-uncore-freq: Fix missing uncore sysfs during CPU hotplug
The following is an automated shortlog grouped by driver:
alienware-wmi-wmax:
- Add support for Alienware m15 R7
- Fix uninitialized variable due to bad error handling
amd: pmc:
- Require at least 2.5 seconds between HW sleep cycles
asus-wmi:
- Disable OOBE state after resume from hibernation
ideapad-laptop:
- add support for some new buttons
intel: hid:
- Add Pantherlake support
intel-uncore-freq:
- Fix missing uncore sysfs during CPU hotplug
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSCSUwRdwTNL2MhaBlZrE9hU+XOMQUCaBCM3AAKCRBZrE9hU+XO
MeW8AQD5t/iQE5eFDy5ohB0BW/ytVuGlgOIFsRjNjxqHNYIlSQEAon+cCpu6xXCc
6VQQDqnEcYgUWeyndOSJCo/FWXwlOw0=
=rjnk
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform drivers fixes from Ilpo Järvinen:
"Fixes and new HW support
- amd/pmc: Require at least 2.5 seconds between HW sleep cycles
- alienware-wmi-wmax:
- Add support for Alienware m15 R7
- Fix error handling to avoid uninitialized variable
- asus-wmi: Disable OOBE state also on resume
- ideapad-laptop: Support a few new buttons
- intel/hid: Add Panther Lake support
- intel-uncore-freq: Fix missing uncore sysfs during CPU hotplug"
* tag 'platform-drivers-x86-v6.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: ideapad-laptop: add support for some new buttons
platform/x86: asus-wmi: Disable OOBE state after resume from hibernation
platform/x86: alienware-wmi-wmax: Add support for Alienware m15 R7
platform/x86/intel: hid: Add Pantherlake support
platform/x86: alienware-wmi-wmax: Fix uninitialized variable due to bad error handling
platform/x86/intel-uncore-freq: Fix missing uncore sysfs during CPU hotplug
platform/x86/amd: pmc: Require at least 2.5 seconds between HW sleep cycles
* pass 'size' rather than 'end' to memblock_set_node() as that function
expects
* fix a corner case when memblock.reserved is doubled at
memmap_init_reserved_pages() and the newly reserved block won't have nid
assigned
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEeOVYVaWZL5900a/pOQOGJssO/ZEFAmgQcBAQHHJwcHRAa2Vy
bmVsLm9yZwAKCRA5A4Ymyw79kTJhB/47k2dGWPOANZHaDfPZRCscDdp9iJCyV71D
PjJ+LHPXswQ5AA3v7cioXhlXF1+sqOUx+Hy4ZPmk+UCAJhAtVv7nj2V7t+F9QHM/
qtmSpYRc0bCESc55LPKIEW8q1A6VbZH5Obg15xs54X2UaBCARA2kR9rBq39cnhl0
vK4ygu70rI/Yi/IuxDitw4UV2k3wdep8jWdCnQWe0+qzpft5KY3kozylJQUK6k8k
TOjjm/1EJa3P4bwzmBdkz86eYLGinfuB3Y0XK7oY6Ji5QKKMNvOsJC0hO2dQMQ1n
8vBBfwYlytlFG27cmnHvvE+HkyNiNNRr5Hcyk+gfnguR7stH+uq6
=T4cO
-----END PGP SIGNATURE-----
Merge tag 'fixes-2025-04-29' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock
Pull memblock fixes from Mike Rapoport:
"Fixes for nid setting in memmap_init_reserved_pages():
- pass 'size' rather than 'end' to memblock_set_node() as that
function expects
- fix a corner case when memblock.reserved is doubled at
memmap_init_reserved_pages() and the newly reserved block
won't have nid assigned"
* tag 'fixes-2025-04-29' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
memblock tests: add test for memblock_set_node
mm/memblock: repeat setting reserved region nid if array is doubled
mm/memblock: pass size instead of end to memblock_set_node()
On r6x2b6x2g6x2 displays not enough blank data is sent to blank the
entire screen. When support for these displays was added, the dirty
function was updated to handle the different amount of data, but
blanking was not, and remained hardcoded as 2 bytes per pixel.
This change applies almost the same algorithm used in the dirty function
to the blank function, but there is no fb available at that point, and
no concern about having to transform any data, so the dbidev pixel
format is always used for calculating the length.
Fixes: 4aebb79021 ("drm/mipi-dbi: Add support for DRM_FORMAT_RGB888")
Signed-off-by: Russell Cloran <rcloran@gmail.com>
Link: https://lore.kernel.org/r/20250415053259.79572-1-rcloran@gmail.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The drm_gem_shmem_test_get_pages_sgt() gets a scatter-gather table using
the drm_gem_shmem_get_sg_table() function and rightfully calls
sg_free_table() on it. However, it's also supposed to kfree() the
returned sg_table, but doesn't.
This leads to a memory leak, reported by kmemleak. Fix it by adding a
kunit action to kfree the sgt when the test ends.
Reported-by: Philipp Stanner <phasta@mailbox.org>
Closes: https://lore.kernel.org/dri-devel/a7655158a6367ac46194d57f4b7433ef0772a73e.camel@mailbox.org/
Fixes: 93032ae634 ("drm/test: add a test suite for GEM objects backed by shmem")
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20250408140758.1831333-1-mripard@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Add two quirks for the WDC Blue SN550 (PCI ID 15b7:5009) based on user
reports and hardware analysis:
- NVME_QUIRK_NO_DEEPEST_PS:
liaozw talked to me the problem and solved with
nvme_core.default_ps_max_latency_us=0, so add the quirk.
I also found some reports in the following link.
- NVME_QUIRK_BROKEN_MSI:
after get the lspci from Jack Rio.
I think that the disk also have NVME_QUIRK_BROKEN_MSI.
described in commit d5887dc6b6 ("nvme-pci: Add quirk for broken MSIs")
as sean said in link which match the MSI 1/32 and MSI-X 17.
Log:
lspci -nn | grep -i memory
03:00.0 Non-Volatile memory controller [0108]: Sandisk Corp SanDisk Ultra 3D / WD PC SN530, IX SN530, Blue SN550 NVMe SSD (DRAM-less) [15b7:5009] (rev 01)
lspci -v -d 15b7:5009
03:00.0 Non-Volatile memory controller: Sandisk Corp SanDisk Ultra 3D / WD PC SN530, IX SN530, Blue SN550 NVMe SSD (DRAM-less) (rev 01) (prog-if 02 [NVM Express])
Subsystem: Sandisk Corp WD Blue SN550 NVMe SSD
Flags: bus master, fast devsel, latency 0, IRQ 35, IOMMU group 10
Memory at fe800000 (64-bit, non-prefetchable) [size=16K]
Memory at fe804000 (64-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 3
Capabilities: [90] MSI: Enable- Count=1/32 Maskable- 64bit+
Capabilities: [b0] MSI-X: Enable+ Count=17 Masked-
Capabilities: [c0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [150] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [1b8] Latency Tolerance Reporting
Capabilities: [300] Secondary PCI Express
Capabilities: [900] L1 PM Substates
Kernel driver in use: nvme
dmesg | grep nvme
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-6.12.20-amd64-desktop-rolling root=UUID= ro splash quiet nvme_core.default_ps_max_latency_us=0 DEEPIN_GFXMODE=
[ 0.059301] Kernel command line: BOOT_IMAGE=/vmlinuz-6.12.20-amd64-desktop-rolling root=UUID= ro splash quiet nvme_core.default_ps_max_latency_us=0 DEEPIN_GFXMODE=
[ 0.542430] nvme nvme0: pci function 0000:03:00.0
[ 0.560426] nvme nvme0: allocated 32 MiB host memory buffer.
[ 0.562491] nvme nvme0: 16/0/0 default/read/poll queues
[ 0.567764] nvme0n1: p1 p2 p3 p4 p5 p6 p7 p8 p9
[ 6.388726] EXT4-fs (nvme0n1p7): mounted filesystem ro with ordered data mode. Quota mode: none.
[ 6.893421] EXT4-fs (nvme0n1p7): re-mounted r/w. Quota mode: none.
[ 7.125419] Adding 16777212k swap on /dev/nvme0n1p8. Priority:-2 extents:1 across:16777212k SS
[ 7.157588] EXT4-fs (nvme0n1p6): mounted filesystem r/w with ordered data mode. Quota mode: none.
[ 7.165021] EXT4-fs (nvme0n1p9): mounted filesystem r/w with ordered data mode. Quota mode: none.
[ 8.036932] nvme nvme0: using unchecked data buffer
[ 8.096023] block nvme0n1: No UUID available providing old NGUID
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=d5887dc6b6c054d0da3cd053afc15b7be1f45ff6
Link: https://lore.kernel.org/all/20240422162822.3539156-1-sean.anderson@linux.dev/
Reported-by: liaozw <hedgehog-002@163.com>
Closes: https://bbs.deepin.org.cn/post/286300
Reported-by: rugk <rugk+github@posteo.de>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=208123
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This commit adds NVME_QUIRK_NO_DEEPEST_PS and NVME_QUIRK_BOGUS_NID for
device [126f:1001].
It is similar to commit e89086c43f ("drivers/nvme: Add quirks for
device 126f:2262")
Diff is according the dmesg, use NVME_QUIRK_IGNORE_DEV_SUBNQN.
dmesg | grep -i nvme0:
nvme nvme0: pci function 0000:01:00.0
nvme nvme0: missing or invalid SUBNQN field.
nvme nvme0: 12/0/0 default/read/poll queues
Link:https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e89086c43f0500bc7c4ce225495b73b8ce234c1f
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A zero return means the reset was successfully scheduled. We don't want
to unquiesce the queues while the reset_work is pending, as that will
just flush out requeued requests to a failed completion.
Fixes: 71a5bb153b ("nvme: ensure disabling pairs with unquiesce")
Reported-by: Dhankaran Singh Ajravat <dhankaran@meta.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The conversion function from MIDI 1.0 to UMP packet contains an
internal buffer to keep the incoming MIDI bytes, and its size is 4, as
it was supposed to be the max size for a MIDI1 UMP packet data.
However, the implementation overlooked that SysEx is handled in a
different format, and it can be up to 6 bytes, as found in
do_convert_to_ump(). It leads eventually to a buffer overflow, and
may corrupt the memory when a longer SysEx message is received.
The fix is simply to extend the buffer size to 6 to fit with the SysEx
UMP message.
Fixes: 0b5288f5fe ("ALSA: ump: Add legacy raw MIDI support")
Reported-by: Argusee <vr@darknavy.com>
Link: https://patch.msgid.link/20250429124845.25128-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
__ublk_check_and_get_req() is only called from ublk_check_and_get_req()
and ublk_register_io_buf(), the same check has been covered in the two
calling sites.
So remove the check from __ublk_check_and_get_req().
Suggested-by: Caleb Sander Mateos <csander@purestorage.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250429022941.1718671-5-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The simple check of UBLK_IO_FLAG_OWNED_BY_SRV can avoid incorrect
register/unregister io buffer easily, so check it before calling
starting to register/un-register io buffer.
Also only allow io buffer register/unregister uring_cmd in case of
UBLK_F_SUPPORT_ZERO_COPY.
Also mark argument 'ublk_queue *' of ublk_register_io_buf as const.
Reviewed-by: Caleb Sander Mateos <csander@purestorage.com>
Fixes: 1f6540e2aa ("ublk: zc register/unregister bvec")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250429022941.1718671-4-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
UBLK_F_USER_COPY and UBLK_F_SUPPORT_ZERO_COPY are two different
features, and shouldn't be coupled together.
Commit 1f6540e2aa ("ublk: zc register/unregister bvec") enables
user copy automatically in case of UBLK_F_SUPPORT_ZERO_COPY, this way
isn't correct.
So decouple zero copy from user copy, and use independent helper to
check each one.
Fixes: 1f6540e2aa ("ublk: zc register/unregister bvec")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250429022941.1718671-3-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 57e13a2e8c ("selftests: ublk: support user recovery") starts to
support UBLK_F_NEED_GET_DATA for covering recovery feature, however the
ublk utility implementation isn't done correctly.
Fix it by supporting UBLK_F_NEED_GET_DATA correctly.
Also add test generic_07 for covering UBLK_F_NEED_GET_DATA.
Reviewed-by: Caleb Sander Mateos <csander@purestorage.com>
Fixes: 57e13a2e8c ("selftests: ublk: support user recovery")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250429022941.1718671-2-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
On newer SoCs intr_target_bit position is at 8 instead of 5. Fix it.
Also add missing intr_wakeup_present_bit and intr_wakeup_enable_bit which
enables forwarding of GPIO interrupts to parent PDC interrupt controller.
Fixes: afe9803e3b ("pinctrl: qcom: Add sm8750 pinctrl driver")
Signed-off-by: Maulik Shah <maulik.shah@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Melody Olvera <melody.olvera@oss.qualcomm.com>
Link: https://lore.kernel.org/20250429-pinctrl_sm8750-v2-1-87d45dd3bd82@oss.qualcomm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Deferred probe with pm_runtime_put() may delay clock disable, causing
incorrect clock usage count. Use pm_runtime_put_sync() to ensure the
clock is disabled immediately.
Fixes: 13d6eb20fc ("i2c: imx-lpi2c: add runtime pm support")
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Cc: <stable@vger.kernel.org> # v4.16+
Link: https://lore.kernel.org/r/20250421062341.2471922-1-carlos.song@nxp.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The list of registers to capture on a GPU hang includes some that
require steering. Unfortunately, the flag to say this was being wiped
to due a missing OR on the assignment of the next flag field.
Fix that.
Fixes: b170d696c1 ("drm/xe/guc: Add XE_LP steered register lists")
Cc: Zhanjun Dong <zhanjun.dong@intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: "Thomas Hellström" <thomas.hellstrom@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-xe@lists.freedesktop.org
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Zhanjun Dong <zhanjun.dong@intel.com>
Link: https://lore.kernel.org/r/20250417195215.3002210-2-John.C.Harrison@Intel.com
(cherry picked from commit 532da44b54)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
xe_svm_range_alloc() returns ERR_PTR(-ENOMEM) on failure and there is a
dereference of "range" after that:
--> range->gpusvm = gpusvm;
In xe_svm_range_alloc(), when memory allocation fails return NULL
instead to handle this situation.
Fixes: 99624bdff8 ("drm/gpusvm: Add support for GPU Shared Virtual Memory")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/adaef4dd-5866-48ca-bc22-4a1ddef20381@stanley.mountain/
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250323124907.3946370-1-harshit.m.mogalapalli@oracle.com
(cherry picked from commit 7a0322122c)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
We can hit this limit fairly easy when we have to reconstuct large
amounts of alloc info on large filesystems.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
If loosing a btree won't cause data loss - i.e. it's an alloc btree, or
we can easily reconstruct it - we shouldn't require user action to
continue repair.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
