Some weird behaviors were observed when connection is really good and
packets are small. It appears that sometime, number of packets in queues
can exceed 255 and generate an overflow in field usage_count.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20191217161318.31402-4-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some rare cases, driver may not have any available tx_retry_policies.
In this case, the driver asks to mac80211 to stop sending data. However,
it seems that a race is possible and a few frames can be sent to the
driver. In this case, driver can't wait for free tx_retry_policies since
wfx_tx() must be atomic. So, this patch fix this case by sending these
frames with the special policy number 15.
The firmware normally use policy 15 to send internal frames (PS-poll,
beacons, etc...). So, it is not a so bad fallback.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20191217161318.31402-3-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device and driver maintain a cache of rate policies (aka.
tx_retry_policy in hardware API).
When hif_reset() is sent to hardware, device resets its cache of rate
policies. In order to keep driver in sync, it is necessary to do the
same on driver.
Note, when driver tries to use a rate policy that has not been defined
on device, data is sent at 1Mbps. So, this patch should fix abnormal
throughput observed sometime after a reset of the interface.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20191217161318.31402-2-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), scripts/checkpatch.pl warns the use of ---help---.
Kconfig still supports ---help---, but new code should avoid using it.
Let's stop advertising it in documentation.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Command queuing has been reported broken on some systems based on Intel
GLK. A separate patch disables command queuing in some cases.
This patch adds a quirk for broken command queuing, which enables users
with problems to disable command queuing using sdhci module parameters for
quirks.
Fixes: 8ee82bda23 ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191217095349.14592-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Command queuing has been reported broken on some Lenovo systems based on
Intel GLK. This is likely a BIOS issue, so disable command queuing for
Intel GLK if the BIOS vendor string is "LENOVO".
Fixes: 8ee82bda23 ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191217095349.14592-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Two previous patches introduced below quirks for P2020 platforms.
- SDHCI_QUIRK_RESET_AFTER_REQUEST
- SDHCI_QUIRK_BROKEN_TIMEOUT_VAL
The patches made a mistake to add them in quirks2 of sdhci_host
structure, while they were defined for quirks.
host->quirks2 |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
host->quirks2 |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
This patch is to fix them.
host->quirks |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
Fixes: 05cb6b2a66 ("mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 support")
Fixes: a46e427125 ("mmc: sdhci-of-esdhc: add erratum eSDHC5 support")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191216031842.40068-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Get_pid_task() needs to be paired with a put_pid or we leak a pid
reference every time a banned client tries to create a context.
v2:
* task_pid_nr helper exists! (Chris)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: b083a0870c ("drm/i915: Add per client max context ban limit")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217170933.8108-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit ba16a48af7)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Since commit e5dadff4b0 ("drm/i915: Protect request retirement with
timeline->mutex"), the request retirement can happen outside of the
struct_mutex serialised only by the timeline->mutex. We drop the
timeline->mutex on submitting the request (i915_request_add) so after
that point, it is liable to be freed. Make sure our local reference is
kept alive until we have finished attaching it to the signalers. (Note
that this erodes the argument that i915_request_add should consume the
reference, but that is a slightly larger patch!)
Fixes: e5dadff4b0 ("drm/i915: Protect request retirement with timeline->mutex")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217134729.3297818-1-chris@chris-wilson.co.uk
(cherry picked from commit e14177f197)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Removing the 'hotplug-status' node in netback_remove() is wrong; the script
may not have completed. Only remove the node once the watch has fired and
has been unregistered.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
...as the comment above the function states.
The switch to Initialising at the start of the function is somewhat bogus
as the toolstack will have set that initial state anyway. To behave
correctly, a backend should switch to InitWait once it has set up all
xenstore values that may be required by a initialising frontend. This
patch calls backend_switch_state() to make the transition at the
appropriate point.
NOTE: backend_switch_state() ignores errors from xenbus_switch_state()
and so this patch removes an error path from netback_probe(). This
means a failure to change state at this stage (in the absence of
other failures) will leave the device instantiated. This is highly
unlikley to happen as a failure to change state would indicate a
failure to write to xenstore, and that will trigger other error
paths. Also, a 'stuck' device can still be cleaned up using 'unbind'
in any case.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
...of xenbus.c
This is a cosmetic function re-ordering to reduce churn in a subsequent
patch. Some style fix-up was done to make checkpatch.pl happier.
No functional change.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dev_hold has to be called always in rx_queue_add_kobject.
Otherwise usage count drops below 0 in case of failure in
kobject_init_and_add.
Fixes: b8eb718348 ("net-sysfs: Fix reference count leak in rx|netdev_queue_add_kobject")
Reported-by: syzbot <syzbot+30209ea299c09d8785c9@syzkaller.appspotmail.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: David Miller <davem@davemloft.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As flower rules are added, they are given a stats ID based on the number
of rules that can be supported in firmware. Only after the initial
allocation of all available IDs does the driver begin to reuse those that
have been released.
The initial allocation of IDs was modified to account for multiple memory
units on the offloaded device. However, this introduced a bug whereby the
counter that controls the IDs could be decremented before the ID was
assigned (where it is further decremented). This means that the stats ID
could be assigned as -1/0xfffffff which is out of range.
Fix this by only decrementing the main counter after the current ID has
been assigned.
Fixes: 467322e262 ("nfp: flower: support multiple memory units for filter offloads")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_link_touch() is not exported, or defined outside of the
file it is in so make it static to avoid the following warning:
net/dsa/dsa2.c:127:17: warning: symbol 'dsa_link_touch' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/atheros/ag71xx.c: In function 'ag71xx_probe':
drivers/net/ethernet/atheros/ag71xx.c:1776:30: warning: passing argument 2 of
'of_get_phy_mode' makes pointer from integer without a cast [-Wint-conversion]
In file included from drivers/net/ethernet/atheros/ag71xx.c:33:
./include/linux/of_net.h:15:69: note: expected 'phy_interface_t *'
{aka 'enum <anonymous> *'} but argument is of type 'int'
Fixes: 0c65b2b90d ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shahjada Abul Husain says:
====================
cxgb4/chtls: fix issues related to high priority region
The high priority region introduced by:
commit c219399988 ("cxgb4: add support for high priority filters")
had caused regression in some code paths, leading to connection
failures for the ULDs.
This series of patches attempt to fix the regressions.
Patch 1 fixes some code paths that have been missed to consider
the high priority region.
Patch 2 fixes ULD connection failures due to wrong TID base that
had been shifted after the high priority region.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the hardware TID index is assumed to start from index 0.
However, with the following changeset,
commit c219399988 ("cxgb4: add support for high priority filters")
hardware TID index can start after the high priority region, which
has introduced a regression resulting in connection failures for
ULDs.
So, fix all related code to properly recalculate the TID start index
based on whether high priority filters are enabled or not.
Fixes: c219399988 ("cxgb4: add support for high priority filters")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c219399988 ("cxgb4: add support for high priority filters")
has missed considering high priority region calculation in some code
paths. This patch fixes them.
Fixes: c219399988 ("cxgb4: add support for high priority filters")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrii Nakryiko says:
====================
Simplify skeleton usage by embedding source BPF object file inside skeleton
itself. This allows to keep skeleton and object file in sync at all times with
no chance of confusion.
Also, add bpftool-gen.rst manpage, explaining concepts and ideas behind
skeleton. In examples section it also includes a complete small BPF
application utilizing skeleton, as a demonstration of API.
Patch #2 also removes BPF_EMBED_OBJ, as there is currently no use of it.
v2->v3:
- (void) in no-args function (Alexei);
- bpftool-gen.rst code block formatting fix (Alexei);
- simplified xxx__create_skeleton to fill in obj and return error code;
v1->v2:
- remove whitespace from empty lines in code blocks (Yonghong).
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add bpftool-gen.rst describing skeleton on the high level. Also include
a small, but complete, example BPF app (BPF side, userspace side, generated
skeleton) in example section to demonstrate skeleton API and its usage.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20191218052552.2915188-4-andriin@fb.com
Drop BPF_EMBED_OBJ and struct bpf_embed_data now that skeleton automatically
embeds contents of its source object file. While BPF_EMBED_OBJ is useful
independently of skeleton, we are currently don't have any use cases utilizing
it, so let's remove them until/if we need it.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20191218052552.2915188-3-andriin@fb.com
Embed contents of BPF object file used for BPF skeleton generation inside
skeleton itself. This allows to keep BPF object file and its skeleton in sync
at all times, and simpifies skeleton instantiation.
Also switch existing selftests to not require BPF_EMBED_OBJ anymore.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20191218052552.2915188-2-andriin@fb.com
Fix missing '*' kernel-doc notation that causes this warning:
../include/linux/netdevice.h:1779: warning: bad line: spinlock
Fixes: ab92d68fc2 ("net: core: add generic lockdep keys")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_pacing_shift can be read and written without lock
synchronization. This patch adds annotations to
document this fact and avoid future syzbot complains.
This might also avoid unexpected false sharing
in sk_pacing_shift_update(), as the compiler
could remove the conditional check and always
write over sk->sk_pacing_shift :
if (sk->sk_pacing_shift != val)
sk->sk_pacing_shift = val;
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ql_alloc_large_buffers() has the usual RX buffer allocation
loop where it allocates skbs and maps them for DMA. It also
treats failure as a fatal error.
There are (at least) three bugs in the error paths:
1. ql_free_large_buffers() assumes that the lrg_buf[] entry for the
first buffer that couldn't be allocated will have .skb == NULL.
But the qla_buf[] array is not zero-initialised.
2. ql_free_large_buffers() DMA-unmaps all skbs in lrg_buf[]. This is
incorrect for the last allocated skb, if DMA mapping failed.
3. Commit 1acb8f2a7a ("net: qlogic: Fix memory leak in
ql_alloc_large_buffers") added a direct call to dev_kfree_skb_any()
after the skb is recorded in lrg_buf[], so ql_free_large_buffers()
will double-free it.
The bugs are somewhat inter-twined, so fix them all at once:
* Clear each entry in qla_buf[] before attempting to allocate
an skb for it. This goes half-way to fixing bug 1.
* Set the .skb field only after the skb is DMA-mapped. This
fixes the rest.
Fixes: 1357bfcf71 ("qla3xxx: Dynamically size the rx buffer queue ...")
Fixes: 0f8ab89e82 ("qla3xxx: Check return code from pci_map_single() ...")
Fixes: 1acb8f2a7a ("net: qlogic: Fix memory leak in ql_alloc_large_buffers")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported a memory leak when an allocation fails within
genradix_prealloc() for output streams. That's because
genradix_prealloc() leaves initialized members initialized when the
issue happens and SCTP stack will abort the current initialization but
without cleaning up such members.
The fix here is to always call genradix_free() when genradix_prealloc()
fails, for output and also input streams, as it suffers from the same
issue.
Reported-by: syzbot+772d9e36c490b18d51d1@syzkaller.appspotmail.com
Fixes: 2075e50caf ("sctp: convert to genradix")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a filesystem is unmounted, we currently call fsnotify_sb_delete()
before evict_inodes(), which means that fsnotify_unmount_inodes()
must iterate over all inodes on the superblock looking for any inodes
with watches. This is inefficient and can lead to livelocks as it
iterates over many unwatched inodes.
At this point, SB_ACTIVE is gone and dropping refcount to zero kicks
the inode out out immediately, so anything processed by
fsnotify_sb_delete / fsnotify_unmount_inodes gets evicted in that loop.
After that, the call to evict_inodes will evict everything else with a
zero refcount.
This should speed things up overall, and avoid livelocks in
fsnotify_unmount_inodes().
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Anything that walks all inodes on sb->s_inodes list without rescheduling
risks softlockups.
Previous efforts were made in 2 functions, see:
c27d82f fs/drop_caches.c: avoid softlockups in drop_pagecache_sb()
ac05fbb inode: don't softlockup when evicting inodes
but there hasn't been an audit of all walkers, so do that now. This
also consistently moves the cond_resched() calls to the bottom of each
loop in cases where it already exists.
One loop remains: remove_dquot_ref(), because I'm not quite sure how
to deal with that one w/o taking the i_lock.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Some configuration items are messed up during conflict resolving. For
example, STRICT_DEVMEM should not in testing menu, but kunit should.
This patch fixes all of them.
[akpm@linux-foundation.org: coding style fixes]
Link: http://lkml.kernel.org/r/20191209155653.7509-1-changbin.du@gmail.com
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 0a432dcbeb ("mm: shrinker: make shrinker not depend on
memcg kmem"), shrinkers' idr is protected by CONFIG_MEMCG instead of
CONFIG_MEMCG_KMEM, so it makes no sense to protect shrinker idr replace
with CONFIG_MEMCG_KMEM.
And in the CONFIG_MEMCG && CONFIG_SLOB case, shrinker_idr contains only
shrinker, and it is deferred_split_shrinker. But it is never actually
called, since idr_replace() is never compiled due to the wrong #ifdef.
The deferred_split_shrinker all the time is staying in half-registered
state, and it's never called for subordinate mem cgroups.
Link: http://lkml.kernel.org/r/1575486978-45249-1-git-send-email-yang.shi@linux.alibaba.com
Fixes: 0a432dcbeb ("mm: shrinker: make shrinker not depend on memcg kmem")
Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: <stable@vger.kernel.org> [5.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
syzkaller and the fault injector showed that I was wrong to assume that
we could ignore percpu shadow allocation failures.
Handle failures properly. Merge all the allocated areas back into the
free list and release the shadow, then clean up and return NULL. The
shadow is released unconditionally, which relies upon the fact that the
release function is able to tolerate pages not being present.
Also clean up shadows in the recovery path - currently they are not
released, which leaks a bit of memory.
Link: http://lkml.kernel.org/r/20191205140407.1874-3-dja@axtens.net
Fixes: 3c5c3cfb9e ("kasan: support backing vmalloc space with real shadow memory")
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reported-by: syzbot+82e323920b78d54aaed5@syzkaller.appspotmail.com
Reported-by: syzbot+59b7daa4315e07a994f1@syzkaller.appspotmail.com
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Qian Cai <cai@lca.pw>
Cc: Uladzislau Rezki (Sony) <urezki@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
apply_to_page_range() takes an address range, and if any parts of it are
not covered by the existing page table hierarchy, it allocates memory to
fill them in.
In some use cases, this is not what we want - we want to be able to
operate exclusively on PTEs that are already in the tables.
Add apply_to_existing_page_range() for this. Adjust the walker
functions for apply_to_page_range to take 'create', which switches them
between the old and new modes.
This will be used in KASAN vmalloc.
[akpm@linux-foundation.org: reduce code duplication]
[akpm@linux-foundation.org: s/apply_to_existing_pages/apply_to_existing_page_range/]
[akpm@linux-foundation.org: initialize __apply_to_page_range::err]
Link: http://lkml.kernel.org/r/20191205140407.1874-1-dja@axtens.net
Signed-off-by: Daniel Axtens <dja@axtens.net>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Uladzislau Rezki (Sony) <urezki@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Qian Cai <cai@lca.pw>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With CONFIG_KASAN_VMALLOC=y any use of memory obtained via vm_map_ram()
will crash because there is no shadow backing that memory.
Instead of sprinkling additional kasan_populate_vmalloc() calls all over
the vmalloc code, move it into alloc_vmap_area(). This will fix
vm_map_ram() and simplify the code a bit.
[aryabinin@virtuozzo.com: v2]
Link: http://lkml.kernel.org/r/20191205095942.1761-1-aryabinin@virtuozzo.comLink: http://lkml.kernel.org/r/20191204204534.32202-1-aryabinin@virtuozzo.com
Fixes: 3c5c3cfb9e ("kasan: support backing vmalloc space with real shadow memory")
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Alexander Potapenko <glider@google.com>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Qian Cai <cai@lca.pw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 22945688ac ("KVM: PPC: Book3S HV: Support reset of secure
guest") added a call to uv_svm_terminate, which is an ultravisor
call, without any check that the guest is a secure guest or even that
the system has an ultravisor. On a system without an ultravisor,
the ultracall will degenerate to a hypercall, but since we are not
in KVM guest context, the hypercall will get treated as a system
call, which could have random effects depending on what happens to
be in r0, and could also corrupt the current task's kernel stack.
Hence this adds a test for the guest being a secure guest before
doing uv_svm_terminate().
Fixes: 22945688ac ("KVM: PPC: Book3S HV: Support reset of secure guest")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Now that we have all the opcodes handled in terms of command prep and
SQE reuse, add a printk_once() to warn about any potentially new and
unhandled ones.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we defer a request, we can't be reading the opcode again. Ensure that
the user_data and opcode fields are stable. For the user_data we already
have a place for it, for the opcode we can fill a one byte hold and store
that as well. For both of them, assign them when we originally read the
SQE in io_get_sqring(). Any code that uses sqe->opcode or sqe->user_data
is switched to req->opcode and req->user_data.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we defer this command as part of a link, we have to make sure that
the SQE data has been read upfront. Integrate the timeout remove op into
the prep handling to make it safe for SQE reuse.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we defer this command as part of a link, we have to make sure that
the SQE data has been read upfront. Integrate the async cancel op into
the prep handling to make it safe for SQE reuse.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we defer these commands as part of a link, we have to make sure that
the SQE data has been read upfront. Integrate the poll add/remove into
the prep handling to make it safe for SQE reuse.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The rules are as follows, if IOSQE_IO_HARDLINK is specified, then it's a
link and there is no need to set IOSQE_IO_LINK separately, though it
could be there. Add proper check and ensure that IOSQE_IO_HARDLINK
implies IOSQE_IO_LINK.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We're currently not retaining sqe data for accept, fsync, and
sync_file_range. None of these commands need data outside of what
is directly provided, hence it can't go stale when the request is
deferred. However, it can get reused, if an application reuses
SQE entries.
Ensure that we retain the information we need and only read the sqe
contents once, off the submission path. Most of this is just moving
code into a prep and finish function.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We pass in req->sqe for all of them, no need to pass it in as the
request is always passed in. This is a necessary prep patch to be
able to cleanup/fix the request prep path.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Some of these code paths assume that any force_nonblock == true issue
is not prepped, but that's not true if we did prep as part of link setup
earlier. Check if we already have an async context allocate before
setting up a new one.
Cleanup the async context setup in general, we have a lot of duplicated
code there.
Fixes: 03b1230ca1 ("io_uring: ensure async punted sendmsg/recvmsg requests copy data")
Fixes: f67676d160 ("io_uring: ensure async punted read/write requests copy iovec")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Libbpf is trying to recognize BPF program type based on its section name
during bpf_object__open() phase. This is not strictly enforced and user code
has ability to specify/override correct BPF program type after open. But if
BPF program is using custom section name, libbpf will still emit warnings,
which can be quite annoying to users. This patch reduces log level of
information messages emitted by libbpf if section name is not canonical. User
can still get a list of all supported section names as debug-level message.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191217234228.1739308-1-andriin@fb.com
DT property definitions must be under a 'properties' keyword. This was
missing for 'snps,tso' in an if/then clause. A meta-schema fix will
catch future errors like this.
Fixes: 7db3545aef ("dt-bindings: net: stmmac: Convert the binding to a schemas")
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
This fixes two issues with the newly introduced libbpf_common.h file:
- The header failed to include <string.h> for the definition of memset()
- The new file was not included in the install_headers rule in the Makefile
Both of these issues cause breakage when installing libbpf with 'make
install' and trying to use it in applications.
Fixes: 544402d4b4 ("libbpf: Extract common user-facing helpers")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20191217112810.768078-1-toke@redhat.com
