On KMB, ADV bridge must be programmed and powered on prior to
MIPI DSI HW initialization.
v2: changed to atomic_bridge_chain_enable (Sam)
Fixes: 98521f4d4b ("drm/kmb: Mipi DSI part of the display driver")
Co-developed-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211019230719.789958-1-anitha.chrisanthus@intel.com
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Due to HW limitations, KMB cannot change height, width, or
pixel format after initial plane configuration.
v2: removed memset disp_cfg as it is already zero.
Fixes: 7f7b96a8a0 ("drm/kmb: Add support for KeemBay Display")
Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211013233632.471892-4-anitha.chrisanthus@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Don't clear the shared DPHY registers common to MIPI Rx and MIPI Tx during
DSI initialization since this was causing MIPI Rx reset. Rest of the
writes are bitwise, so will not affect Mipi Rx side.
Fixes: 98521f4d4b ("drm/kmb: Mipi DSI part of the display driver")
Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211013233632.471892-3-anitha.chrisanthus@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
KMB only supports single resolution(1080p), this commit checks for
1920x1080x60 or 1920x1080x59 in crtc_mode_valid.
Also, modes with vfp < 4 are not supported in KMB display. This change
prunes display modes with vfp < 4.
v2: added vfp check
Fixes: 7f7b96a8a0 ("drm/kmb: Add support for KeemBay Display")
Co-developed-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link:https://patchwork.freedesktop.org/patch/msgid/20211013233632.471892-2-anitha.chrisanthus@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Use a different value for system clock offset in the
ppl/llp ratio calculations for clocks higher than 500 Mhz.
Fixes: 98521f4d4b ("drm/kmb: Mipi DSI part of the display driver")
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211013233632.471892-1-anitha.chrisanthus@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
This adjusts sync values according to the datasheet
Fixes: 1c243751c0 ("drm/panel: ilitek-ili9881c: add support for Feixin K101-IM2BYL02 panel")
Co-developed-by: Marius Gripsgard <marius@ubports.com>
Signed-off-by: Dan Johansen <strit@manjaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210818214818.298089-1-strit@manjaro.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The mxsfb->crtc.funcs may already be NULL when unloading the driver,
in which case calling mxsfb_irq_disable() via drm_irq_uninstall() from
mxsfb_unload() leads to NULL pointer dereference.
Since all we care about is masking the IRQ and mxsfb->base is still
valid, just use that to clear and mask the IRQ.
Fixes: ae1ed00932 ("drm: mxsfb: Stop using DRM simple display pipeline helper")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Abrecht <public@danielabrecht.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211016210446.171616-1-marex@denx.de
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
B0 internal rev_id is 0x01, B1 internal rev_id is 0x02.
The external rev_id for B0 and B1 is 0x20.
The original expression is not suitable for B1.
v2: squash in fix for display code (Alex)
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
bios_golden_init will override dccg_init during init_hw.
[How]
Move dccg_init to after bios_golden_init.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[why]
The original latencies were causing underflow in some modes
[how]
Replace with the up-to-date watermark values based on new measurments
Reviewed-by: Ahmad Othman <ahmad.othman@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
Z9 latency is higher than when we originally tuned the watermark
parameters, causing underflow. Increasing the value until the latency
issues is resolved.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
Immediate flip can be enabled dynamically and has higher BW requirements
when validating which voltage mode to use.
If we validate when it's not set then potentially DCFCLK will be too low
and we will underflow.
[How]
DM always requires support so always require it as part of DML input
parameters.
This can't be enabled unconditionally on older ASIC because it blocks
some expected modes so only target DCN3.1 for now.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
Prefetch BW calculated is lower than the DML reference because of a
porting error that's excluding cursor and row bandwidth from the
pixel data bandwidth.
[How]
Change the dml_max4 to dml_max3 and include cursor and row bandwidth
in the same calculation as the rest of the pixel data during vactive.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[why]
The requirement is that image width up to 4096 shall be supported
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Size can be any value and is user controlled resulting in overwriting the
40 byte array wr_buf with an arbitrary length of data from buf.
Signed-off-by: Thelford Williams <tdwilliamsiv@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Until we better understand the stability issues caused by frequent
frequency changes, lets limit them to a618.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Caleb Connolly <caleb.connolly@linaro.org>
Link: https://lore.kernel.org/r/20211018153627.2787882-1-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/gpu/drm/panel/panel-olimex-lcd-olinuxino.o: in function `lcd_olinuxino_probe':
panel-olimex-lcd-olinuxino.c:(.text+0x303): undefined reference to `crc32_le'
Fixes: 17fd7a9d32 ("drm/panel: Add support for Olimex LCD-OLinuXino panel")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211012115242.10325-1-vegard.nossum@oracle.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix a build error on CONFIG_UML, which does not support (provide)
wbinvd(). UML can use the generic mb() instead.
../drivers/gpu/drm/r128/ati_pcigart.c: In function ‘drm_ati_pcigart_init’:
../drivers/gpu/drm/r128/ati_pcigart.c:218:2: error: implicit declaration of function ‘wbinvd’ [-Werror=implicit-function-declaration]
wbinvd();
^~~~~~
Fixes: 68f5d3f3b6 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: linux-um@lists.infradead.org
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211011080006.31081-1-rdunlap@infradead.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 64f7c698be ("drm/nouveau/fifo: add engine_id hook") replaced
fifo/chang84.c g84_fifo_chan_engine() call with an indirect call of
fifo/g84.c g84_fifo_engine_id(). The G84_FIFO_ENGN_* values returned
from the later g84_fifo_engine_id() are incremented by 1 compared to
the previous g84_fifo_chan_engine() return values.
This is fine either way for most of the code, except this one line
where an engine bit programmed into the hardware is derived from the
return value. Decrement the return value accordingly, otherwise the
wrong engine bit is programmed into the hardware and that leads to
the following failure:
nouveau 0000:01:00.0: gr: 00000030 [ILLEGAL_MTHD ILLEGAL_CLASS] ch 1 [003fbce000 DRM] subc 3 class 0000 mthd 085c data 00000420
On the following hardware:
lspci -s 01:00.0
01:00.0 VGA compatible controller: NVIDIA Corporation GT216GLM [Quadro FX 880M] (rev a2)
lspci -ns 01:00.0
01:00.0 0300: 10de:0a3c (rev a2)
Fixes: 64f7c698be ("drm/nouveau/fifo: add engine_id hook")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: <stable@vger.kernel.org> # 5.12+
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211007214117.231472-1-marex@denx.de
Signed-off-by: Dave Airlie <airlied@redhat.com>
Hyper-V supports a hardware cursor feature. It is not used by Linux VM,
but the Hyper-V host still draws a point as an extra mouse pointer,
which is unwanted, especially when Xorg is running.
The hyperv_fb driver uses synthvid_send_ptr() to hide the unwanted pointer.
When the hyperv_drm driver was developed, the function synthvid_send_ptr()
was not copied from the hyperv_fb driver. Fix the issue by adding the
function into hyperv_drm.
Fixes: 76c56a5aff ("drm/hyperv: Add DRM driver for hyperv synthetic video device")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Deepak Rawat <drawat.floss@gmail.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210916193644.45650-1-decui@microsoft.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
Clamp the fbdev surface size of the available maximumi height to avoid
failing to init console emulation. An example error is shown below.
bad framebuffer height 2304, should be >= 768 && <= 768
[drm] Initialized simpledrm 1.0.0 20200625 for simple-framebuffer.0 on minor 0
simple-framebuffer simple-framebuffer.0: [drm] *ERROR* fbdev: Failed to setup generic emulation (ret=-22)
This is especially a problem with drivers that have very small screen
sizes and cannot over-allocate at all.
v2:
* reduce warning level (Ville)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 11e8f5fd22 ("drm: Add simpledrm driver")
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reported-by: Amanoel Dawod <kernel@amanoeldawod.com>
Reported-by: Zoltán Kővágó <dirty.ice.hu@gmail.com>
Reported-by: Michael Stapelberg <michael+lkml@stapelberg.ch>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.14+
Link: https://patchwork.freedesktop.org/patch/msgid/20211005070355.7680-1-tzimmermann@suse.de
Signed-off-by: Dave Airlie <airlied@redhat.com>
In commit e11f5bd822 ("drm: Add support for DP 1.4 Compliance edid
corruption test") the function connector_bad_edid() started assuming
that the memory for the EDID passed to it was big enough to hold
`edid[0x7e] + 1` blocks of data (1 extra for the base block). It
completely ignored the fact that the function was passed `num_blocks`
which indicated how much memory had been allocated for the EDID.
Let's fix this by adding a bounds check.
This is important for handling the case where there's an error in the
first block of the EDID. In that case we will call
connector_bad_edid() without having re-allocated memory based on
`edid[0x7e]`.
Fixes: e11f5bd822 ("drm: Add support for DP 1.4 Compliance edid corruption test")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211005192905.v2.1.Ib059f9c23c2611cb5a9d760e7d0a700c1295928d@changeid
Signed-off-by: Dave Airlie <airlied@redhat.com>
As per the comment on top of acpi_evaluate_dsm():
| * Evaluate device's _DSM method with specified GUID, revision id and
| * function number. Caller needs to free the returned object.
We should free the returned object of acpi_evaluate_dsm() to avoid memory
leakage. Otherwise the kmemleak splat will be triggered at boot time (if we
compile kernel with CONFIG_DEBUG_TEST_DRIVER_REMOVE=y).
Fixes: 8e55f99c51 ("drm/i915: Invoke another _DSM to enable MUX on HP Workstation laptops")
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210906033541.862-1-yuzenghui@huawei.com
(cherry picked from commit 149ac2e7ae)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Set number of engines before attempting to create contexts so the
function free_engines can clean up properly. Also check return of
alloc_engines for NULL.
v2:
(Tvrtko)
- Send as stand alone patch
(John Harrison)
- Check for alloc_engines returning NULL
v3:
(Checkpatch / Tvrtko)
- Remove braces around single line if statement
Cc: Jason Ekstrand <jason@jlekstrand.net>
Fixes: d4433c7600 ("drm/i915/gem: Use the proto-context to handle create parameters (v5)")
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001155825.6762-1-matthew.brost@intel.com
(cherry picked from commit 84edf53776)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On R-Car D3 and E3, the LVDS encoders provide the pixel clock to the DU,
even when LVDS outputs are not used. For this reason, the rcar-lvds
driver probes successfully on those platforms even if no further bridge
or panel is connected to the LVDS output, in order to provide the
rcar_lvds_clk_enable() and rcar_lvds_clk_disable() functions to the DU
driver.
If an LVDS output isn't connected, trying to create a DRM connector for
the output will fail. Fix this by skipping connector creation in that
case, and also skip creation of the DRM encoder as there's no point in
an encoder without a connector.
Fixes: e9e056949c ("drm: rcar-du: lvds: Convert to DRM panel bridge helper")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
(cherry picked from commit 187502afe8)
Signed-off-by: Dave Airlie <airlied@redhat.com>
* Fix a new crash on dev file close if the dev file was opened when
GPU is not loaded (such as missing fw in initrd)
* Switch to single drm_sched_entity per priority level per drm_file
to unbreak multi-context userspace
* Serialize GMU access to fix GMU OOB errors
* Various error path fixes
* A couple integer overflow fixes
* Fix mdp5 cursor plane WARNs
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtD4u7yyiy+BQLmibUCbn=AdDRu7FrmdViHVx0QrcGf8g@mail.gmail.com
This disables a lock which wasn't enabled and it does not disable
the first lock in the array.
Fixes: 6e0eb52eba ("drm/msm/dsi: Parse bus clocks from a list")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211001123409.GG2283@kili
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Return an error code if msm_dsi_manager_validate_current_config().
Don't return success.
Fixes: 8b03ad30e3 ("drm/msm/dsi: Use one connector for dual DSI mode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211001123308.GF2283@kili
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The downstream driver models this PLL lock check as an if-elseif-else.
The only way to reach the else case where pll_locked=true [1] is by
succeeding both readl_poll_timeout_atomic calls (which return zero on
success) in the if _and_ elseif condition. Hence both the "lock" and
"ready" bit need to be tested in the SM_READY_STATUS register before
considering the PLL locked and ready to go.
Tested on the Sony Xperia XA2 Ultra (nile-discovery, sdm630).
[1]: https://source.codeaurora.org/quic/la/kernel/msm-4.19/tree/drivers/clk/qcom/mdss/mdss-dsi-pll-14nm-util.c?h=LA.UM.9.2.1.r1-08000-sdm660.0#n302
Fixes: f079f6d999 ("drm/msm/dsi: Add PHY/PLL for 8x96")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210906202552.824598-1-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The commit 9f91f22aaf ("drm/msm/dsi: remove duplicate fields from
dsi_pll_Nnm instances") mistakenly changed registered clock names. While
the platform is in progress of migration to using clock properties in
the dts rather than the global clock names, we should provide backwards
compatibility. Thus restore registerd global clock names.
Fixes: 9f91f22aaf ("drm/msm/dsi: remove duplicate fields from dsi_pll_Nnm instances")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210921162245.1858118-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Both PINGPONG4 and PINGPONG5 IRQ registers are using the
same address, which is incorrect. PINGPONG4 should use the
register offset 30, and PINGPONG5 should use the register
offset 31 according to the downstream driver.
Fixes: 667e9985ee ("drm/msm/dpu: replace IRQ lookup with the data in hw catalog")
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210819133636.2045766-1-robert.foss@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Since commit 98659487b8 ("drm/msm: add support to take dpu snapshot")
the following NULL pointer dereference is seen on i.MX53:
[ 3.275493] msm msm: bound 30000000.gpu (ops a3xx_ops)
[ 3.287174] [drm] Initialized msm 1.8.0 20130625 for msm on minor 0
[ 3.293915] 8<--- cut here ---
[ 3.297012] Unable to handle kernel NULL pointer dereference at virtual address 00000028
[ 3.305244] pgd = (ptrval)
[ 3.307989] [00000028] *pgd=00000000
[ 3.311624] Internal error: Oops: 805 [#1] SMP ARM
[ 3.316430] Modules linked in:
[ 3.319503] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.14.0+g682d702b426b #1
[ 3.326652] Hardware name: Freescale i.MX53 (Device Tree Support)
[ 3.332754] PC is at __mutex_init+0x14/0x54
[ 3.336969] LR is at msm_disp_snapshot_init+0x24/0xa0
i.MX53 does not use the DPU controller.
Fix the problem by only calling msm_disp_snapshot_init() on platforms that
use the DPU controller.
Cc: stable@vger.kernel.org
Fixes: 98659487b8 ("drm/msm: add support to take dpu snapshot")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210914174831.2044420-1-festevam@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
These error paths returned 1 on failure, instead of a negative error
code. This would lead to an Oops in the caller. A second problem is
that the check for "if (ret != -ENODATA)" did not work because "ret" was
set to 1.
Fixes: 5785dd7a8e ("drm/msm: Fix duplicate gpu node in icc summary")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211001125904.GK2283@kili
Signed-off-by: Rob Clark <robdclark@chromium.org>
This code returns 1 on error instead of a negative error. It leads to
an Oops in the caller. A second problem is that the check for
"if (ret != -ENODATA)" cannot be true because "ret" is set to 1.
Fixes: 5785dd7a8e ("drm/msm: Fix duplicate gpu node in icc summary")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211001125759.GJ2283@kili
Signed-off-by: Rob Clark <robdclark@chromium.org>
The initialization of pointer dev dereferences pointer edp before
edp is null checked, so there is a potential null pointer deference
issue. Fix this by only dereferencing edp after edp has been null
checked.
Addresses-Coverity: ("Dereference before null check")
Fixes: ab5b0107cc ("drm/msm: Initial add eDP support in msm drm driver (v5)")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210929121857.213922-1-colin.king@canonical.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
The return type of ktime_divns() is s64. The timeout_to_jiffies() currently
assigns the result of this ktime_divns() to unsigned long, which on 32 bit
systems may overflow. Furthermore, the result of this function is sometimes
also passed to functions which expect signed long, dma_fence_wait_timeout()
is one such example.
Fix this by adjusting the type of remaining_jiffies to s64, so we do not
suffer overflow there, and return a value limited to range of 0..INT_MAX,
which is safe for all usecases of this timeout.
The above overflow can be triggered if userspace passes in too large timeout
value, larger than INT_MAX / HZ seconds. The kernel detects it and complains
about "schedule_timeout: wrong timeout value %lx" and generates a warning
backtrace.
Note that this fixes commit 6cedb8b377 ("drm/msm: avoid using 'timespec'"),
because the previously used timespec_to_jiffies() function returned unsigned
long instead of s64:
static inline unsigned long timespec_to_jiffies(const struct timespec *value)
Fixes: 6cedb8b377 ("drm/msm: avoid using 'timespec'")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Rob Clark <robdclark@chromium.org>
Cc: stable@vger.kernel.org # 5.6+
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210917005913.157379-1-marex@denx.de
Signed-off-by: Rob Clark <robdclark@chromium.org>
There is no devfreq on a3xx at the moment since gpu_busy is not
implemented. This means that msm_devfreq_init() will return early
and the entire devfreq setup is skipped.
However, msm_devfreq_active() and msm_devfreq_idle() are still called
unconditionally later, causing a NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
Internal error: Oops: 96000004 [#1] PREEMPT SMP
CPU: 0 PID: 133 Comm: ring0 Not tainted 5.15.0-rc1 #4
Hardware name: Longcheer L8150 (DT)
pc : mutex_lock_io+0x2bc/0x2f0
lr : msm_devfreq_active+0x3c/0xe0 [msm]
Call trace:
mutex_lock_io+0x2bc/0x2f0
msm_gpu_submit+0x164/0x180 [msm]
msm_job_run+0x54/0xe0 [msm]
drm_sched_main+0x2b0/0x4a0 [gpu_sched]
kthread+0x154/0x160
ret_from_fork+0x10/0x20
Fix this by adding a check in msm_devfreq_active/idle() which ensures
that devfreq was actually initialized earlier.
Fixes: 9bc9557017 ("drm/msm: Devfreq tuning")
Reported-by: Nikita Travkin <nikita@trvn.ru>
Tested-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210913164556.16284-1-stephan@gerhold.net
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently there is audio not working problem after system resume from suspend
if hdmi monitor stay plugged in at DUT. However this problem does not happen
at normal operation but at a particular test case. The root cause is DP driver
signal audio with connected state at resume which trigger audio trying to setup
audio data path through DP main link but failed due to display port is not setup
and enabled by upper layer framework yet. This patch only have DP driver signal
audio only when DP is in disconnected state so that audio option shows correct
state after system resume. DP driver will not signal audio with connected state
until display enabled executed by upper layer framework where display port is
setup completed and main link is running.
Changes in V2:
-- add details commit text
Fixes: afc9b8b6ba ("drm/msm/dp: signal audio plugged change at dp_pm_resume")
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1632932224-25102-1-git-send-email-khsieh@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
This reverts commit f4be17cd5b.
Commit c1ec54b7b5
("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb")
would cause numerous mtk cmdq mailbox driver warning:
WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198
cmdq_task_exec_done+0xb8/0xe0
So revert that patch and all the patches depend on that patch.
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This reverts commit 8cdcb36534.
Commit c1ec54b7b5
("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb")
would cause numerous mtk cmdq mailbox driver warning:
WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198
cmdq_task_exec_done+0xb8/0xe0
So revert that patch and all the patches depend on that patch.
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This reverts commit bc9241be73.
Commit c1ec54b7b5
("drm/mediatek: Use mailbox rx_callback instead of cmdq_task_cb")
would cause numerous mtk cmdq mailbox driver warning:
WARNING: CPU: 0 PID: 0 at drivers/mailbox/mtk-cmdq-mailbox.c:198
cmdq_task_exec_done+0xb8/0xe0
So revert that patch and all the patches depend on that patch.
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
