commit d55bda1b3e upstream.
"of_get_named_gpio()" returns a negative error value if it fails
and drivers should check for this. This missing check was now
added to the matrix_keypad driver.
In my case "of_get_named_gpio()" returned -EPROBE_DEFER because
the referenced GPIOs belong to an I/O expander, which was not yet
probed at the point in time when the matrix_keypad driver was
loading. Because the driver did not check for errors from the
"of_get_named_gpio()" routine, it was assuming that "-EPROBE_DEFER"
is actually a GPIO number and continued as usual, which led to further
errors like this later on:
WARNING: CPU: 3 PID: 167 at drivers/gpio/gpiolib.c:114
gpio_to_desc+0xc8/0xd0
invalid GPIO -517
Note that the "GPIO number" -517 in the error message above is
actually "-EPROBE_DEFER".
As part of the patch a misleading error message "no platform data defined"
was also removed. This does not lead to information loss because the other
error paths in matrix_keypad_parse_dt() already print an error.
Signed-off-by: Christian Hoff <christian_hoff@gmx.net>
Suggested-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d88a331e4 upstream.
In case of error, the function gpio_to_desc() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1aa577f5e upstream.
Workqueue, 'set_brightness_work' is used for scheduling brightness control.
This workqueue is canceled when the LED class device is unregistered.
Currently, LED subsystem handles like below.
cancel_work_sync(&led_cdev->set_brightness_work)
led_set_brightness(led_cdev, LED_OFF)
However, this could be a problem.
Workqueue is going to be canceled but LED device needs to be off.
The worst case is null pointer access due to scheduling a workqueue.
LED module is loaded.
LED driver private data is allocated by using devm_zalloc().
LED module is unloaded.
led_classdev_unregister() is called.
cancel_work_sync()
led_set_brightness(led_cdev, LED_OFF)
schedule_work() if LED driver uses brightness_set_blocking()
In the meantime, driver private data will be freed.
..scheduling..
brightness_set_blocking() callback is invoked.
For the brightness control, LED driver tries to access private
data but resource is removed!
To avoid this problem, LED subsystem should turn off the brightness first
and wait for completion.
led_set_brightness(led_cdev, LED_OFF)
flush_work(&led_cdev->set_brightness_work)
It guarantees that LED driver turns off the brightness prior to
resource management.
Cc: linux-leds@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f16703360d upstream.
Some PWMs are disabled by default or the default pin setting
does not match the LED_OFF state (e.g., active-low leds).
Hence, the driver may end up reporting 0 brightness, but
the leds are actually on using full brightness, because
it never enforces its default configuration.
So enforce it by calling led_pwm_set() after successfully
registering the device.
Tested on a Phytec phyFLEX i.MX6Q board based on kernel
v3.19.5.
Signed-off-by: Markus Hofstaetter <markus.hofstaetter@ait.ac.at>
Tested-by: Markus Hofstaetter <markus.hofstaetter@ait.ac.at>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cd25cbb2f upstream.
After 2dd4531686 ("kgdboc: Fix restrict error"), kgdboc_option_setup is
now only used when built in, resulting in a warning when compiled as a
module:
drivers/tty/serial/kgdboc.c:134:12: warning: 'kgdboc_option_setup' defined but not used [-Wunused-function]
static int kgdboc_option_setup(char *opt)
^~~~~~~~~~~~~~~~~~~
Move the function under the appropriate ifdef for builtin only.
Fixes: 2dd4531686 ("kgdboc: Fix restrict error")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dd4531686 upstream.
There's an error when compiled with restrict:
drivers/tty/serial/kgdboc.c: In function ‘configure_kgdboc’:
drivers/tty/serial/kgdboc.c:137:2: error: ‘strcpy’ source argument is the same
as destination [-Werror=restrict]
strcpy(config, opt);
^~~~~~~~~~~~~~~~~~~
As the error implies, this is from trying to use config as both source and
destination. Drop the call to the function where config is the argument
since nothing else happens in the function.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42c335f7e6 upstream.
When copying attributes, the len argument was padded out and the
resulting memcpy() would copy beyond the end of the source buffer.
Avoid this, and use size_t for val_len to avoid all the casts.
Similarly, avoid source buffer casts and use void *.
Additionally enforces val_len can be represented by u16 and that the DMA
buffer was not overflowed. Fixes the size of mfa, which is not
FC_FDMI_PORT_ATTR_MAXFRAMESIZE_LEN (but it will be padded up to 4). This
was noticed by the future CONFIG_FORTIFY_SOURCE checks.
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81df022b68 upstream.
Cleanly fill memory for "vendor" and "model" with 0-bytes for the
"compatible" case rather than adding only a single 0 byte. This
simplifies the devinfo code a a bit, and avoids mistakes in other places
of the code (not in current upstream, but we had one such mistake in the
SUSE kernel).
[mkp: applied by hand and added braces]
Signed-off-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc25ab0676 upstream.
If the platform has no IO space, ioregs is placed next to the already
allocated regs. In this case, it should not be separately freed.
This prevents a kernel warning from __vunmap "Trying to vfree()
nonexistent vm area" when unloading the driver.
Fixes: 0dd68309b9 ("drm/ast: Try to use MMIO registers when PIO isn't supported")
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24c3456c8d upstream.
If for some reason we failed to query the mr status, we need to make sure
to provide sufficient information for an ambiguous error (guard error on
sector 0).
Fixes: 0a7a08ad6f ("IB/iser: Implement check_protection")
Cc: <stable@vger.kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58930cced0 upstream.
As gcc-8 points out, the bit mask check makes no sense here:
drivers/staging/rts5208/sd.c: In function 'ext_sd_send_cmd_get_rsp':
drivers/staging/rts5208/sd.c:4130:25: error: bitwise comparison always evaluates to true [-Werror=tautological-compare]
However, the code is even more bogus, as we have already
checked for the SD_RSP_TYPE_R0 case earlier in the function
and returned success. As seen in the mmc/sd driver core,
SD_RSP_TYPE_R0 means "no response" anyway, so checking for
a particular response would not help either.
This just removes the nonsensical code to get rid of the
warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c5a50e8e7 upstream.
The bfa driver has a number of real issues with string termination
that gcc-8 now points out:
drivers/scsi/bfa/bfad_bsg.c: In function 'bfad_iocmd_port_get_attr':
drivers/scsi/bfa/bfad_bsg.c:320:9: error: argument to 'sizeof' in 'strncpy' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c: In function 'bfa_fcs_fabric_psymb_init':
drivers/scsi/bfa/bfa_fcs.c:775:9: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:781:9: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:788:9: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:801:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:808:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c: In function 'bfa_fcs_fabric_nsymb_init':
drivers/scsi/bfa/bfa_fcs.c:837:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:844:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:852:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c: In function 'bfa_fcs_fabric_psymb_init':
drivers/scsi/bfa/bfa_fcs.c:778:2: error: 'strncat' output may be truncated copying 10 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs.c:784:2: error: 'strncat' output may be truncated copying 30 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs.c:803:3: error: 'strncat' output may be truncated copying 44 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs.c:811:3: error: 'strncat' output may be truncated copying 16 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs.c: In function 'bfa_fcs_fabric_nsymb_init':
drivers/scsi/bfa/bfa_fcs.c:840:2: error: 'strncat' output may be truncated copying 10 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs.c:847:2: error: 'strncat' output may be truncated copying 30 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c: In function 'bfa_fcs_fdmi_get_hbaattr':
drivers/scsi/bfa/bfa_fcs_lport.c:2657:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs_lport.c:2659:11: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs_lport.c: In function 'bfa_fcs_lport_ms_gmal_response':
drivers/scsi/bfa/bfa_fcs_lport.c:3232:5: error: 'strncpy' output may be truncated copying 16 bytes from a string of length 247 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c: In function 'bfa_fcs_lport_ns_send_rspn_id':
drivers/scsi/bfa/bfa_fcs_lport.c:4670:3: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c:4682:3: error: 'strncat' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c: In function 'bfa_fcs_lport_ns_util_send_rspn_id':
drivers/scsi/bfa/bfa_fcs_lport.c:5206:3: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c:5215:3: error: 'strncat' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c: In function 'bfa_fcs_fdmi_get_portattr':
drivers/scsi/bfa/bfa_fcs_lport.c:2751:2: error: 'strncpy' specified bound 128 equals destination size [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcbuild.c: In function 'fc_rspnid_build':
drivers/scsi/bfa/bfa_fcbuild.c:1254:2: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcbuild.c:1253:25: note: length computed here
drivers/scsi/bfa/bfa_fcbuild.c: In function 'fc_rsnn_nn_build':
drivers/scsi/bfa/bfa_fcbuild.c:1275:2: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
In most cases, this can be addressed by correctly calling strlcpy and
strlcat instead of strncpy/strncat, with the size of the destination
buffer as the last argument.
For consistency, I'm changing the other callers of strncpy() in this
driver the same way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67a3b63a54 upstream.
gcc-8 points out a condition that almost certainly doesn't
do what the author had in mind:
drivers/gpu/drm/gma500/mdfld_intel_display.c: In function 'mdfldWaitForPipeEnable':
drivers/gpu/drm/gma500/mdfld_intel_display.c:102:37: error: bitwise comparison always evaluates to false [-Werror=tautological-compare]
This changes it to a simple bit mask operation to check
whether the bit is set.
Fixes: 026abc3332 ("gma500: initial medfield merge")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170905074741.435324-1-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6484a67729 upstream.
gcc '-Wunused-but-set-variable' warning:
drivers/misc/mic/scif/scif_rma.c: In function 'scif_create_remote_lookup':
drivers/misc/mic/scif/scif_rma.c:373:25: warning:
variable 'vmalloc_num_pages' set but not used [-Wunused-but-set-variable]
'vmalloc_num_pages' should be used to determine if the address is
within the vmalloc range.
Fixes: ba612aa8b4 ("misc: mic: SCIF memory registration and unregistration")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit effd14f66c upstream.
Cherry G230 Stream 2.0 (G85-231) and 3.0 (G85-232) need this quirk to
function correctly. This fixes a but where double pressing numlock locks
up the device completely with need to replug the keyboard.
Signed-off-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a84a1bcc99 upstream.
There are two new Realtek card readers require ums-realtek to work
correctly.
Add the new IDs to support them.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77e75fda94 upstream.
of_dma_controller_free() was not called on module onloading.
This lead to a soft lockup:
watchdog: BUG: soft lockup - CPU#0 stuck for 23s!
Modules linked in: at_hdmac [last unloaded: at_hdmac]
when of_dma_request_slave_channel() tried to call ofdma->of_dma_xlate().
Cc: stable@vger.kernel.org
Fixes: bbe89c8e3d ("at_hdmac: move to generic DMA binding")
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98f5f93225 upstream.
The leak was found when opening/closing a serial port a great number of
time, increasing kmalloc-32 in slabinfo.
Each time the port was opened, dma_request_slave_channel() was called.
Then, in at_dma_xlate(), atslave was allocated with devm_kzalloc() and
never freed. (Well, it was free at module unload, but that's not what we
want).
So, here, kzalloc is more suited for the job since it has to be freed in
atc_free_chan_resources().
Cc: stable@vger.kernel.org
Fixes: bbe89c8e3d ("at_hdmac: move to generic DMA binding")
Reported-by: Mario Forner <m.forner@be4energy.com>
Suggested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9a764c1e59 ]
The response for a SNMP request can consist of multiple parts, which
the cmd callback stages into a kernel buffer until all parts have been
received. If the callback detects that the staging buffer provides
insufficient space, it bails out with error.
This processing is buggy for the first part of the response - while it
initially checks for a length of 'data_len', it later copies an
additional amount of 'offsetof(struct qeth_snmp_cmd, data)' bytes.
Fix the calculation of 'data_len' for the first part of the response.
This also nicely cleans up the memcpy code.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cfc435198f ]
skb is freed via dev_kfree_skb_any, however, skb->len is read then. This
may result in a use-after-free bug.
Fixes: e6161d6426 ("rapidio/rionet: rework driver initialization and removal")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3fdd34643f which was
upstream commit 4ec7cece87.
From Dietmar May's report on the stable mailing list
(https://www.spinics.net/lists/stable/msg272201.html):
> I've run into some problems which appear due to (a) recent patch(es) on
> the wlcore wifi driver.
>
> 4.4.160 - commit 3fdd34643f
> 4.9.131 - commit afeeecc764436f31d4447575bb9007732333818c
>
> Earlier versions (4.9.130 and 4.4.159 - tested back to 4.4.49) do not
> exhibit this problem. It is still present in 4.9.141.
>
> master as of 4.20.0-rc4 does not exhibit this problem.
>
> Basically, during client association when in AP mode (running hostapd),
> handshake may or may not complete following a noticeable delay. If
> successful, then the driver fails consistently in warn_slowpath_null
> during disassociation. If unsuccessful, the wifi client attempts multiple
> times, sometimes failing repeatedly. I've had clients unable to connect
> for 3-5 minutes during testing, with the syslog filled with dozens of
> backtraces. syslog details are below.
>
> I'm working on an embedded device with a TI 3352 ARM processor and a
> murata wl1271 module in sdio mode. We're running a fully patched ubuntu
> 18.04 ARM build, with a kernel built from kernel.org's stable/linux repo <https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-4.9.y&id=afeeecc764436f31d4447575bb9007732333818c>.
> Relevant parts of the kernel config are included below.
>
> The commit message states:
>
> > /I've only seen this few times with the runtime PM patches enabled so
> > this one is probably not needed before that. This seems to work
> > currently based on the current PM implementation timer. Let's apply
> > this separately though in case others are hitting this issue./
> We're not doing anything explicit with power management. The device is an
> IoT edge gateway with battery backup, normally running on wall power. The
> battery is currently used solely to shut down the system cleanly to avoid
> filesystem corruption.
>
> The device tree is configured to keep power in suspend; but the device
> should never suspend, so in our case, there is no need to call
> wl1271_ps_elp_wakeup() or wl1271_ps_elp_sleep(), as occurs in the patch.
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5478ad10e7 upstream.
If vesafb attaches to the AST device, it configures the framebuffer memory
for uncached access by default. When ast.ko later tries to attach itself to
the device, it wants to use write-combining on the framebuffer memory, but
vesefb's existing configuration for uncached access takes precedence. This
results in reduced performance.
Removing the framebuffer's configuration before loding the AST driver fixes
the problem. Other DRM drivers already contain equivalent code.
Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1112963
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: <stable@vger.kernel.org>
Tested-by: Y.C. Chen <yc_chen@aspeedtech.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 958c0bd860 upstream.
Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on
Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3,
after clear port reset it works fine.
Since this device is registered on USB3 roothub at boot,
when port status reports not superspeed, xhci_get_port_status will call
an uninitialized completion in bus_state[0].
Kernel will hang because of NULL pointer.
Restrict the USB2 resume status check in USB2 roothub to fix hang issue.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b97b3d9fb5 upstream.
If we are not echoing the data to userspace or the console is in icanon
mode, then perhaps it is a "secret" so we should wipe it once we are
done with it.
This mirrors the logic that the audit code has.
Reported-by: aszlig <aszlig@nix.build>
Tested-by: Milan Broz <gmazyland@gmail.com>
Tested-by: Daniel Zatovic <daniel.zatovic@gmail.com>
Tested-by: aszlig <aszlig@nix.build>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9a8e5fce0 upstream.
After we are done with the tty buffer, zero it out.
Reported-by: aszlig <aszlig@nix.build>
Tested-by: Milan Broz <gmazyland@gmail.com>
Tested-by: Daniel Zatovic <daniel.zatovic@gmail.com>
Tested-by: aszlig <aszlig@nix.build>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82715ac71e upstream.
When the firmware starts, it doesn't have any regulatory
information, hence it uses the world wide limitations. The
driver can feed the firmware with previous knowledge that
was kept in the driver, but the firmware may still not
update its internal tables.
This happens when we start a BSS interface, and then the
firmware can change the regulatory tables based on our
location and it'll use more lenient, location specific
rules. Then, if the firmware is shut down (when the
interface is brought down), and then an AP interface is
created, the firmware will forget the country specific
rules.
The host will think that we are in a certain country that
may allow channels and will try to teach the firmware about
our location, but the firmware may still not allow to drop
the world wide limitations and apply country specific rules
because it was just re-started.
In this case, the firmware will reply with MCC_RESP_ILLEGAL
to the MCC_UPDATE_CMD. In that case, iwlwifi needs to let
the upper layers (cfg80211 / hostapd) know that the channel
list they know about has been updated.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201105
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04dfaa53a0 upstream.
When the driver is unloading, in qla2x00_remove_one(), there is a single
call/point in time to abort ongoing commands, qla2x00_abort_all_cmds(),
which is still several steps away from the call to scsi_remove_host().
If more commands continue to arrive and be processed during that
interval, when the driver is tearing down and releasing its structures,
it might potentially hit an oops due to invalid memory access:
Unable to handle kernel paging request for data at address 0x00000138
<...>
NIP [d000000004700a40] qla2xxx_queuecommand+0x80/0x3f0 [qla2xxx]
LR [d000000004700a10] qla2xxx_queuecommand+0x50/0x3f0 [qla2xxx]
So, fail commands in qla2xxx_queuecommand() if the UNLOADING bit is set.
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afa3dfd42d upstream.
If ufshcd pltfrm/pci driver's probe fails for some reason then ensure
that scsi host is released to avoid memory leak but managed memory
allocations (via devm_* calls) need not to be freed explicitly on probe
failure as memory allocated with these functions is automatically freed
on driver detach.
Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30fc33f1ef upstream.
UFS devfreq clock scaling work may require clocks to be ON if it need to
execute some UFS commands hence it may request for clock hold before
issuing the command. But if UFS clock gating work is already running in
parallel, ungate work would end up waiting for the clock gating work to
finish and as clock gating work would also wait for the clock scaling
work to finish, we would enter in deadlock state. Here is the call trace
during this deadlock state:
Workqueue: devfreq_wq devfreq_monitor
__switch_to
__schedule
schedule
schedule_timeout
wait_for_common
wait_for_completion
flush_work
ufshcd_hold
ufshcd_send_uic_cmd
ufshcd_dme_get_attr
ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div
ufs_qcom_clk_scale_notify
ufshcd_scale_clks
ufshcd_devfreq_target
update_devfreq
devfreq_monitor
process_one_work
worker_thread
kthread
ret_from_fork
Workqueue: events ufshcd_gate_work
__switch_to
__schedule
schedule
schedule_preempt_disabled
__mutex_lock_slowpath
mutex_lock
devfreq_monitor_suspend
devfreq_simple_ondemand_handler
devfreq_suspend_device
ufshcd_gate_work
process_one_work
worker_thread
kthread
ret_from_fork
Workqueue: events ufshcd_ungate_work
__switch_to
__schedule
schedule
schedule_timeout
wait_for_common
wait_for_completion
flush_work
__cancel_work_timer
cancel_delayed_work_sync
ufshcd_ungate_work
process_one_work
worker_thread
kthread
ret_from_fork
This change fixes this deadlock by doing this in devfreq work (devfreq_wq):
Try cancelling clock gating work. If we are able to cancel gating work
or it wasn't scheduled, hold the clock reference count until scaling is
in progress. If gate work is already running in parallel, let's skip
the frequecy scaling at this time and it will be retried once next scaling
window expires.
Reviewed-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2a785ac23 upstream.
The ungate work turns on the clock before it exits hibern8, if the link
was put in hibern8 during clock gating work. There occurs a race
condition when clock scaling work calls ufshcd_hold() to make sure low
power states cannot be entered, but that returns by checking only
whether the clocks are on. This causes the clock scaling work to issue
UIC commands when the link is in hibern8 causing failures. Make sure we
exit hibern8 state before returning from ufshcd_hold().
Callstacks for race condition:
ufshcd_scale_gear
ufshcd_devfreq_scale
ufshcd_devfreq_target
update_devfreq
devfreq_monitor
process_one_work
worker_thread
kthread
ret_from_fork
ufshcd_uic_hibern8_exit
ufshcd_ungate_work
process_one_work
worker_thread
kthread
ret_from_fork
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3ce73d69a upstream.
In this change there are a few fixes of possible NULL pointer access and
possible access to index that exceeds array boundaries.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d8bd85c2c upstream.
Marvell p2p device disappears from the list of p2p peers on the other
p2p device after disconnection.
It happens due to a bug in driver. When interface is changed from p2p
to station, certain variables(bss_type, bss_role etc.) aren't correctly
updated. This patch corrects them to fix the issue.
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[AmitP: Refactored to fix driver file path in linux-4.4.y]
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c44c040300 upstream.
At couple of places in cleanup path, we are just going through the
skb queue and freeing them without unlinking. This leads to a crash
when other thread tries to do skb_dequeue() and use already freed node.
The problem is freed by unlinking skb before freeing it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[AmitP: Refactored to fix driver file path in linux-4.4.y]
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9afdd6128c upstream.
The call to krealloc() in wsm_buf_reserve() directly assigns the newly
returned memory to buf->begin. This is all fine except when krealloc()
failes we loose the ability to free the old memory pointed to by
buf->begin. If we just create a temporary variable to assign memory to
and assign the memory to it we can mitigate the memory leak.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9735082a7c ]
The "Xbox One PDP Wired Controller - Camo series" has a different
product-id than the regular PDP controller and the PDP stealth series,
but it uses the same initialization sequence. This patch adds the
product-id of the camo series to the structures that handle the other
PDP Xbox One controllers.
Signed-off-by: Ramses Ramírez <ramzeto@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd6bee81c9 ]
This fixes using the controller with SDL2.
SDL2 has a naive algorithm to apply the correct settings to a controller.
For X-Box compatible controllers it expects that the controller name
contains a variation of a 'XBOX'-string.
This patch changes the identifier to contain "X-Box" as substring. Tested
with Steam and C-Dogs-SDL which both detect the controller properly after
adding this patch.
Fixes: c1ba08390a ("Input: xpad - add GPD Win 2 Controller USB IDs")
Cc: stable@vger.kernel.org
Signed-off-by: Enno Boland <gottox@voidlinux.eu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1ba08390a ]
GPD Win 2 Website: http://www.gpd.hk/gpdwin2.asp
Tested on a unit from the first production run sent to Indiegogo backers
Signed-off-by: Ethan Lee <flibitijibibo@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a01308031c ]
input_set_capability() and input_set_abs_param() will do it for you.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6c848572f ]
Adds support for a PDP Xbox One controller with device ID
(0x06ef:0x02a4). The Product string for this device is "PDP Wired
Controller for Xbox One - Stealth Series | Phantom Black".
Signed-off-by: Francis Therien <frtherien@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5c9c6a885 ]
Adds support for the current lineup of Xbox One controllers from PDP
(Performance Designed Products). These controllers are very picky with
their initialization sequence and require an additional 2 packets before
they send any input reports.
Signed-off-by: Mark Furneaux <mark@furneaux.ca>
Reviewed-by: Cameron Gutman <aicommander@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 122d6a3473 ]
We should only see devices with interrupt endpoints. Ignore any other
endpoints that we find, so we don't send try to send them interrupt URBs
and trigger a WARN down in the USB stack.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: <stable@vger.kernel.org> # c01b5e7464 Input: xpad - don't depend on endpoint order
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5308d1b83 ]
The PowerA gamepad initialization quirk worked with the PowerA
wired gamepad I had around (0x24c6:0x543a), but a user reported [0]
that it didn't work for him, even though our gamepads shared the
same vendor and product IDs.
When I initially implemented the PowerA quirk, I wanted to avoid
actually triggering the rumble action during init. My tests showed
that my gamepad would work correctly even if it received a rumble
of 0 intensity, so that's what I went with.
Unfortunately, this apparently isn't true for all models (perhaps
a firmware difference?). This non-working gamepad seems to require
the real magic rumble packet that the Microsoft driver sends, which
actually vibrates the gamepad. To counteract this effect, I still
send the old zero-rumble PowerA quirk packet which cancels the
rumble effect before the motors can spin up enough to vibrate.
[0]: https://github.com/paroj/xpad/issues/48#issuecomment-313904867
Reported-by: Kyle Beauchamp <kyleabeauchamp@gmail.com>
Tested-by: Kyle Beauchamp <kyleabeauchamp@gmail.com>
Fixes: 81093c9848 ("Input: xpad - support some quirky Xbox One pads")
Cc: stable@vger.kernel.org # v4.12
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94aef061c7 ]
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be19788c73 ]
XBCD [0][1] is an OpenSource driver for Xbox controllers on Windows.
Later it also started supporting Xbox360 controllers (presumably before
the official Windows driver was released).
It contains a couple device IDs unknown to the Linux driver, so I extracted
those from xbcd.inf and added them to our list.
It has a special type for Wheels and I have the feeling they might need
some extra handling. They all have 'Wheel' in their name, so that
information is available for future improvements.
[0] https://www.s-config.com/xbcd-original-xbox-controllers-win10/
[1] http://www.redcl0ud.com/xbcd.html
Reviewed-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c225370e01 ]
360Controller [0] is an OpenSource driver for Xbox/Xbox360/XboxOne
controllers on macOS.
It contains a couple device IDs unknown to the Linux driver, so I wrote a
small Python script [1] to extract them and feed them into my previous
script [2] to compare them with the IDs known to Linux.
For most devices, this information is not really needed as xpad is able to
automatically detect the type of an unknown Xbox Controller at run-time.
I've therefore stripped all the generic/vague entries.
I've excluded the Logitech G920, it's handled by a HID driver already.
I've also excluded the Scene It! Big Button IR, it's handled by an
out-of-tree driver. [3]
[0] https://github.com/360Controller/360Controller
[1] http://codepad.org/v9GyLKMq
[2] http://codepad.org/qh7jclpD
[3] https://github.com/micolous/xbox360bb
Reviewed-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4706aa0756 ]
Add USB IDs for two more Xbox 360 controllers.
I found them in the pull requests for the xboxdrv userspace driver, which
seems abandoned.
Thanks to psychogony and mkaito for reporting the IDs there!
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Reviewed-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
