Like the odroid-c2 and wetek, the s400 uses the RTL8211F and seems to
suffer from the kind of stability issue.
Doing an iperf3 download test, we can see a significant number of LPI
interrupts on the tx path. After a short while (5 to 15 seconds), the
network connection dies. If using rootfs over NFS, the connection may
also break during the boot sequence.
We still don't have a real explanation for this problem so let's disable
EEE once again.
Fixes: f6f6ac914b ("ARM64: dts: meson-axg: enable ethernet for A113D S400 board")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Vendor firmware/uboot has different reserved regions depending on
firmware version, but current codebase reserves the same regions on
GXL and GXBB, so move the additional reserved memory region to common
.dtsi.
Found when putting a recent vendor u-boot on meson-gxbb-p200.
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Like LibreTech-CC, the USB0 needs the 5V regulator to be enabled to power the
devices on the P212 Reference Design based boards.
Fixes: b9f07cb4f4 ("ARM64: dts: meson-gxl-s905x-p212: enable the USB controller")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Based on updated information from Amlogic, correct the register range
for the SD/eMMC blocks to the right size.
Reported-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There is a problem with the sd-uhs mode when doing a soft reboot.
Switching back from 1.8v to 3.3v messes with the card, which no longer
respond (timeout errors). According to the specification, we should
perform a card reset (power cycling the card) but this is something we
cannot control on this design.
Then the only solution to restore the communication with the card is an
"unplug-plug" which is not acceptable
Until we find a solution, if any, disable the sd-uhs modes on this design.
For the people using uhs at the moment, there will a performance drop as
a result.
Fixes: 3cde63ebc8 ("ARM64: dts: meson-gxl: libretech-cc: enable high speed modes")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The in_pm atomic in hdac_device is an important field used as a flag
as well as a refcount for PM. The existing snd_hdac_power_up/down
helpers already refer to it in the HD-audio core code, while the code
to actually setting the value (atomic_inc() / _dec()) is open-coded in
HDA legacy side, which is hard to find.
This patch adds the helper functions to set/reset the in_pm counter to
HDA core and use them in HDA legacy side, for making it clearer who /
where the PM is managed.
There is no functional changes, just code refactoring.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch addresses Interrupts from south display engine (SDE).
ICP has two registers - SHOTPLUG_CTL_DDI and SHOTPLUG_CTL_TC.
Introduce these registers and their intended values.
Introduce icp_irq_handler().
The icp_irq_postinstall() takes care of
enabling all PCH interrupt sources, to unmask
them as needed with SDEIMR, as is done
done by ibx_irq_pre_postinstall() for earlier platforms.
We do not need to explicitly call the ibx_irq_pre_postinstall().
Also, while changing these,
s/CPT/PPT/CPT-CNP comment.
v2:
- remove redundant register defines.(Lucas)
- Change register names to be more consistent with
previous platforms (Lucas)
v3:
-Reorder bit defines to a more appropriate location.
Change the comments. Confirm in the commit message that
icp_irq_postinstall() need not go to
ibx_irq_pre_postinstall() and ibx_irq_postinstall()
as in earlier platforms. (Paulo)
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
[Paulo: coding style bikesheds and rebases].
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530046343-30649-1-git-send-email-anusha.srivatsa@intel.com
This function is not in use - delete it.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Adit Ranadive <aditr@vmware.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
port_num is untrusted data from the user, so it should be checked after
calling fill_sgid_attr, which validates it.
Fixes: 8d9ec9addd ("IB/core: Add a sgid_attr pointer to struct rdma_ah_attr")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
drm_of_find_possible_crtcs() doesn't work when DW HDMI encoder is
connected to TCON (crtc) through mux in TCON TOP.
In that case TCON TOP HDMI mux input port has to be manually traversed
and checked if it matches any known crtc.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-23-jernej.skrabec@siol.net
Function is useful when drm_of_find_possible_crtcs() can't be used and
custom parsing is needed. This can happen for example when there is a
node with multiple muxes between crtc and encoder.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[maxime: change the function to have a consistent prefix]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-22-jernej.skrabec@siol.net
DW HDMI PHY driver and PHY clock driver share same registers. Make sure
that DW HDMI PHY setup code doesn't change any clock related bits.
During initialization, set PHY PLL parent bit to 0.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-18-jernej.skrabec@siol.net
Current DW HDMI PHY code never prepares and enables PHY clock after it is
created. It's just used as it is. This may work in some cases, but it's
clearly wrong. Fix it by adding proper calls to enable/disable PHY
clock.
Fixes: 4f86e81748 ("drm/sun4i: Add support for H3 HDMI PHY variant")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-17-jernej.skrabec@siol.net
A64 HDMI PHY is similar to H3 HDMI PHY except it has two possible PLL
clock parents. It is compatible to other HDMI PHYs, like that found in
R40.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-16-jernej.skrabec@siol.net
Both mixers have similar capabilities as others SoCs with DE2.
First mixer has 1 VI and 3 UI planes and supports HW scaling on all
planes.
Second mixer has 1 VI and 1 UI planes and also supports HW scaling on
all planes.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-15-jernej.skrabec@siol.net
TV TCONs are always connected to TV or HDMI encoder, so it doesn't make
sense to check if panel or bridge is connected to them.
Check if TCON has channel 0 and only then check for connected panel or
bridges.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-13-jernej.skrabec@siol.net
LVDS and RGB interfaces are always connected to TCONs which have channel
0. It doesn't make sense to try to init them on TV TCONs.
Add a check if TCON has channel 0 before trying to init LVDS or RGB
interface.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-12-jernej.skrabec@siol.net
Current "old" method to find engine worked pretty well for DE2. However,
it doesn't work when TCON TOP is between mixer (engine) and TCON. TCON
TOP has multiple input ports, but current engine search algorithm
expects only one.
This can be fixed by first looking for output port id and selecting
matching input by subtracting 1 for the next round. This work even if
there is only one input and output.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-11-jernej.skrabec@siol.net
TV TCONs (channel 1 only) are always connected to TV or HDMI encoder.
Because of that, all output endpoints on such TCON node will point to a
encoder which is part of component framework.
Correct current graph traversing algorithm in such way that it doesn't
skip output enpoints with id 0 on TV TCONs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-10-jernej.skrabec@siol.net
TCON TOP is different from other nodes in graph by having 3 input and 3
output ports. Additionally, connection to TV TCON might lead back to
HDMI mux input port, creating loops.
Add support for traversing such graph.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-9-jernej.skrabec@siol.net
Until now, each node has one input port and one output port. However,
with TCON TOP this is no longer true. It has 3 input and 3 output ports.
In order to prepare to this situation, split out the code which checks
all endpoints in input port and adds available components to fifo.
This patch doesn't do any functional change.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-8-jernej.skrabec@siol.net
sun4i_drv_add_endpoints() has a memory leak since it uses of_node_put()
when remote is equal to NULL and does nothing when remote has a valid
pointer.
Invert the logic to fix memory leak.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-7-jernej.skrabec@siol.net
As already described in DT binding, TCON TOP is responsible for
configuring display pipeline. In this initial driver focus is on HDMI
pipeline, so TVE and LCD configuration is not implemented.
Implemented features:
- HDMI source selection
- clock driver (TCON and DSI gating)
- connecting mixers and TCONS
Something similar also existed in previous SoCs, except that it was part
of first TCON.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-6-jernej.skrabec@siol.net
TCON TOP main purpose is to configure whole display pipeline. It
determines relationships between mixers and TCONs, selects source TCON
for HDMI, muxes LCD and TV encoder GPIO output, selects TV encoder
clock source and contains additional TV TCON and DSI gates.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-5-jernej.skrabec@siol.net
Currently, amdgpu_do_flip() spinlocks crtc->dev->event_lock and
releases it only after committing updates to the stream.
dc_commit_updates_for_stream() should be moved out of
spinlock for the below reasons:
1. event_lock is supposed to protect access to acrct->pflip_status _only_
2. dc_commit_updates_for_stream() has potential sleep's
and also its not appropriate to be in an atomic state
for such long sequences of code.
Signed-off-by: Shirish S <shirish.s@amd.com>
Suggested-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Support new VCN FW version naming convention:
[31, 28] for VEP interface major version if applicable
[27, 24] for decode interface major version
[23, 20] for encode interface major version
[19, 12] for encode interface minor version
[11, 0] for firmware revision
Bit 20-23, it is encode major and non-zero for new naming convention.
This field is part of version minor and DRM_DISABLED_FLAG in old naming
convention. Since the latest version minor is 0x5B and DRM_DISABLED_FLAG
is zero in old naming convention, this field is always zero so far.
These four bits are used to tell which naming convention is present.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Fang, Peter <Peter.Fang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Here is the UBSAN dump:
[ 3.866656] index 2 is out of range for type 'amdgpu_uvd_inst [2]'
[ 3.866693] Workqueue: events work_for_cpu_fn
[ 3.866702] Call Trace:
[ 3.866710] dump_stack+0x85/0xc5
[ 3.866719] ubsan_epilogue+0x9/0x40
[ 3.866727] __ubsan_handle_out_of_bounds+0x89/0x90
[ 3.866737] ? rcu_read_lock_sched_held+0x58/0x60
[ 3.866746] ? __kmalloc+0x26c/0x2d0
[ 3.866846] amdgpu_fence_driver_start_ring+0x259/0x280 [amdgpu]
[ 3.866896] amdgpu_ring_init+0x12c/0x710 [amdgpu]
[ 3.866906] ? sprintf+0x42/0x50
[ 3.866956] amdgpu_gfx_kiq_init_ring+0x1bc/0x3a0 [amdgpu]
[ 3.867009] gfx_v8_0_sw_init+0x1ad3/0x2360 [amdgpu]
[ 3.867062] ? smu7_init+0xec/0x160 [amdgpu]
[ 3.867109] amdgpu_device_init+0x112c/0x1dc0 [amdgpu]
'ring->me' might be set as 2 with 'amdgpu_gfx_kiq_init_ring', that would
cause out of range for 'amdgpu_uvd_inst[2]'.
v2: simplified with ring type
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- More metadata validation strengthening to prevent crashes.
- Fix extent offset overflow problem when insert_range on a 512b block fs
- Fix some off-by-one errors in the realtime fsmap code
- Fix some math errors in the default resblks calculation when free space
is low
- Fix a problem where stale page contents are exposed via mmap read
after a zero_range at eof
- Fix accounting problems with per-ag reservations causing statfs
reports to vary incorrectly
-----BEGIN PGP SIGNATURE-----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=Aw39
-----END PGP SIGNATURE-----
Merge tag 'xfs-4.18-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"Here are some patches for 4.18 to fix regressions, accounting
problems, overflow problems, and to strengthen metadata validation to
prevent corruption.
This series has been run through a full xfstests run over the weekend
and through a quick xfstests run against this morning's master, with
no major failures reported.
Changes since last update:
- more metadata validation strengthening to prevent crashes.
- fix extent offset overflow problem when insert_range on a 512b
block fs
- fix some off-by-one errors in the realtime fsmap code
- fix some math errors in the default resblks calculation when free
space is low
- fix a problem where stale page contents are exposed via mmap read
after a zero_range at eof
- fix accounting problems with per-ag reservations causing statfs
reports to vary incorrectly"
* tag 'xfs-4.18-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix fdblocks accounting w/ RMAPBT per-AG reservation
xfs: ensure post-EOF zeroing happens after zeroing part of a file
xfs: fix off-by-one error in xfs_rtalloc_query_range
xfs: fix uninitialized field in rtbitmap fsmap backend
xfs: recheck reflink state after grabbing ILOCK_SHARED for a write
xfs: don't allow insert-range to shift extents past the maximum offset
xfs: don't trip over negative free space in xfs_reserve_blocks
xfs: allow empty transactions while frozen
xfs: xfs_iflush_abort() can be called twice on cluster writeback failure
xfs: More robust inode extent count validation
xfs: simplify xfs_bmap_punch_delalloc_range
Timur Tabi no longer works for Qualcomm, and he now has a kernel.org
email address, so update MAINTAINERS accordingly.
Signed-off-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On usual A64 board design the power of HDMI controller is connected to
DLDO1 of the AXP803 PMIC. If this regulator is shut down, the HDMI
output will be blank. Therefore the simplefb driver should keep this
regulator on.
Add the regulator to all currently available A64 boards' simplefb_hdmi
device node, if the board is capable of outputing HDMI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As the U-Boot bootloader now is also capable of initialize the HDMI on
A64 boards, add a simplefb device tree node for accessing the HDMI
framebuffer initialized by the bootloader.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As we have all necessary parts to enable the DE2 CCU on the Allwinner
A64 SoC, add the needed device tree nodes, including the DE2 CCU itself
and the DE2 bus.
The "mixer0-lcd0" simplefb device node is updated to use the DE2 CCU.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As claiming Allwinner A64 SRAM C is a prerequisite for all sub-blocks of
the A64 DE2, not only the CCU sub-block, a bus driver is then written for
enabling the access to the whole DE2 part by claiming the SRAM.
In this situation, the A64 compatible string will be just added with no
other requirments, as they're processed by the parent bus driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner A64 SoC has a DE2 CCU like the one in the DE2 of Allwinner
H5 SoC.
Add a compatible string for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds a new driver for display panels that use the Ilitek ILI9341
controller. It currently supports a single display panel, namely
the YX240QV29-T (e.g. Adafruit 2.4" TFT).
The init sequence is from the Adafruit Python library for the ILI9341
controller. https://github.com/adafruit/Adafruit_Python_ILI9341
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525193623.15533-5-david@lechnology.com
Here are a couple of typo fixes for clk-davinci for 4.18.
Technically, there are not any users of clk-davinci yet in 4.18, so this can
wait until 4.19 if that is easier.
Signed-off-by: David Lechner <david@lechnology.com>
-----BEGIN PGP SIGNATURE-----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=kXdQ
-----END PGP SIGNATURE-----
Merge tag 'clk-davinci-fixes-4.18' of https://github.com/dlech/linux into clk-fixes
Pull davinci clk fixes for 4.18 from David Lechner:
Here are a couple of typo fixes for clk-davinci for 4.18.
* tag 'clk-davinci-fixes-4.18' of https://github.com/dlech/linux:
clk: davinci: fix a typo (which leads to build failures)
clk: davinci: cfgchip: testing the wrong variable
In the next^W forthcoming patch, we will start to defer retiring the
request from the engine list if it is still active on the submission
backend. To preserve the semantics that after wait-for-idle completes
the system is idle and fully retired, we need to therefore wait for the
backends to idle before calling i915_retire_requests().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180627115334.16282-1-chris@chris-wilson.co.uk
Commit 7f0b1bf045 ("arm64: Fix barriers used for page table modifications")
fixed a reported issue with fixmap page-table entries not being visible
to the walker due to a missing DSB instruction. At the same time, it added
ISB instructions to the arm64 set_{pte,pmd,pud} functions, which are not
required by the architecture and make little sense in isolation.
Remove the redundant ISBs.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The implementation of flush_icache_range() includes instruction sequences
which are themselves patched at runtime, so it is not safe to call from
the patching framework.
This patch reworks the alternatives cache-flushing code so that it rolls
its own internal D-cache maintenance using DC CIVAC before invalidating
the entire I-cache after all alternatives have been applied at boot.
Modules don't cause any issues, since flush_icache_range() is safe to
call by the time they are loaded.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Rohit Khanna <rokhanna@nvidia.com>
Cc: Alexander Van Brunt <avanbrunt@nvidia.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The flag IN_MASK_CREATE is introduced as a flag for inotiy_add_watch()
which prevents inotify from modifying any existing watches when invoked.
If the pathname specified in the call has a watched inode associated
with it and IN_MASK_CREATE is specified, fail with an errno of EEXIST.
Use of IN_MASK_CREATE with IN_MASK_ADD is reserved for future use and
will return EINVAL.
RATIONALE
In the current implementation, there is no way to prevent
inotify_add_watch() from modifying existing watch descriptors. Even if
the caller keeps a record of all watch descriptors collected, this is
only sufficient to detect that an existing watch descriptor may have
been modified.
The assumption that a particular path will map to the same inode over
multiple calls to inotify_add_watch() cannot be made as files can be
renamed or deleted. It is also not possible to assume that two distinct
paths do no map to the same inode, due to hard-links or a dereferenced
symbolic link. Further uses of inotify_add_watch() to revert the change
may cause other watch descriptors to be modified or created, merely
compunding the problem. There is currently no system call such as
inotify_modify_watch() to explicity modify a watch descriptor, which
would be able to revert unwanted changes. Thus the caller cannot
guarantee to be able to revert any changes to existing watch decriptors.
Additionally the caller cannot assume that the events that are
associated with a watch descriptor are within the set requested, as any
future calls to inotify_add_watch() may unintentionally modify a watch
descriptor's mask. Thus it cannot currently be guaranteed that a watch
descriptor will only generate events which have been requested. The
program must filter events which come through its watch descriptor to
within its expected range.
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Henry Wilson <henry.wilson@acentic.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Outbound window is used to translate CPU space addresses to PCIe space
addresses when the CPU initiates PCIe transactions.
According to the suggestion of the HW designers, the recommended
solution is to use the default outbound parameters, even though the
current outbound window setting does not cause any known functional
issue.
This patch doesn't address any known functional issue, but aligns to
HW design guidelines, and removes code that isn't needed.
Signed-off-by: Evan Wang <xswang@marvell.com>
[Thomas: tweak commit log.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: handled host->controller dir move]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
In other to mimic other PCIe host controller drivers, introduce an
advk_pcie_valid_device() helper, used in the configuration read/write
functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[lorenzo.pieralisi@arm.com: updated host->controller dir move]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Video PLLs need to be referenced in R40 DT as possible HDMI PHY parent.
Export them.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Display related peripherals need precise clocks to operate correctly.
Allow DE2, TCONs and HDMI to set parent clock.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
