[ Upstream commit a8eb8e6f71 ]
As a result of the execution of the inner while loop, the value
of 'idx' can be equal to LINK_QUAL_MAX_RETRY_NUM. However, this
is not checked after the loop and 'idx' is used to write the
LINK_QUAL_MAX_RETRY_NUM size array 'lq_cmd->rs_table[idx]' below
in the outer loop.
The fix is to check the new value of 'idx' inside the nested loop,
and break both loops if index equals the size. Checking it at the
start is now pointless, so let's remove it.
Detected using the static analysis tool - Svace.
Fixes: be663ab670 ("iwlwifi: split the drivers for agn and legacy devices 3945/4965")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220608171614.28891-1-aleksei.kodanev@bell-sw.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9331f7d3c5 ]
Currently a couple of debug_mask entries are mapped to the same value,
this could enable unintended driver logging. If enabling DP_TX logs was
the intention, then this could also enable PCI logs flooding the dmesg
buffer or vice versa. Fix this by correctly assigning the debug masks.
Found during code review.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Fixes: aa2092a9ba ("ath11k: add raw mode and software crypto support")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220602115621.15339-1-quic_mpubbise@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4ba1ff87b ]
Make sure to allocate resources needed before registering the device.
This specifically avoids having a racing open() trigger a BUG_ON() in
mod_timer() when ath11k_mac_op_start() is called before the
mon_reap_timer as been set up.
I did not see this issue with next-20220310, but I hit it on every probe
with next-20220511. Perhaps some timing changed in between.
Here's the backtrace:
[ 51.346947] kernel BUG at kernel/time/timer.c:990!
[ 51.346958] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
...
[ 51.578225] Call trace:
[ 51.583293] __mod_timer+0x298/0x390
[ 51.589518] mod_timer+0x14/0x20
[ 51.595368] ath11k_mac_op_start+0x41c/0x4a0 [ath11k]
[ 51.603165] drv_start+0x38/0x60 [mac80211]
[ 51.610110] ieee80211_do_open+0x29c/0x7d0 [mac80211]
[ 51.617945] ieee80211_open+0x60/0xb0 [mac80211]
[ 51.625311] __dev_open+0x100/0x1c0
[ 51.631420] __dev_change_flags+0x194/0x210
[ 51.638214] dev_change_flags+0x24/0x70
[ 51.644646] do_setlink+0x228/0xdb0
[ 51.650723] __rtnl_newlink+0x460/0x830
[ 51.657162] rtnl_newlink+0x4c/0x80
[ 51.663229] rtnetlink_rcv_msg+0x124/0x390
[ 51.669917] netlink_rcv_skb+0x58/0x130
[ 51.676314] rtnetlink_rcv+0x18/0x30
[ 51.682460] netlink_unicast+0x250/0x310
[ 51.688960] netlink_sendmsg+0x19c/0x3e0
[ 51.695458] ____sys_sendmsg+0x220/0x290
[ 51.701938] ___sys_sendmsg+0x7c/0xc0
[ 51.708148] __sys_sendmsg+0x68/0xd0
[ 51.714254] __arm64_sys_sendmsg+0x28/0x40
[ 51.720900] invoke_syscall+0x48/0x120
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Fixes: 840c36fa72 ("ath11k: dp: stop rx pktlog before suspend")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220517103436.15867-1-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b88d28146c ]
If the copy_from_user() fails or the user gives invalid date then the
correct thing to do is to return a negative error code. (Currently it
returns success).
I made a copy additional related cleanups:
1) There is no need to check "buffer" for NULL. That's handled by
copy_from_user().
2) The "h2c_len" variable cannot be negative because it is unsigned
and because sscanf() does not return negative error codes.
Fixes: 610247f46f ("rtlwifi: Improve debugging by using debugfs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/YoOLnDkHgVltyXK7@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ee6c5abeb ]
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge rising - but instead rely on Devicetree to configure it.
All Qualcomm DTSI with WCN3990 define the interrupt type as level high,
so the mismatch between DTSI and driver causes rebind issues:
$ echo 18800000.wifi > /sys/bus/platform/drivers/ath10k_snoc/unbind
$ echo 18800000.wifi > /sys/bus/platform/drivers/ath10k_snoc/bind
[ 44.763114] irq: type mismatch, failed to map hwirq-446 for interrupt-controller@17a00000!
[ 44.763130] ath10k_snoc 18800000.wifi: error -ENXIO: IRQ index 0 not found
[ 44.763140] ath10k_snoc 18800000.wifi: failed to initialize resource: -6
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.0.c8-00009-QCAHLSWSC8180XMTPLZ-1
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
Fixes: c963a683e7 ("ath10k: add resource init and deinit for WCN3990")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220513151516.357549-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a69e617e53 upstream.
usbnet uses the work usbnet_deferred_kevent() to perform tasks which may
sleep. On disconnect, completion of the work was originally awaited in
->ndo_stop(). But in 2003, that was moved to ->disconnect() by historic
commit "[PATCH] USB: usbnet, prevent exotic rtnl deadlock":
https://git.kernel.org/tglx/history/c/0f138bbfd83c
The change was made because back then, the kernel's workqueue
implementation did not allow waiting for a single work. One had to wait
for completion of *all* work by calling flush_scheduled_work(), and that
could deadlock when waiting for usbnet_deferred_kevent() with rtnl_mutex
held in ->ndo_stop().
The commit solved one problem but created another: It causes a
use-after-free in USB Ethernet drivers aqc111.c, asix_devices.c,
ax88179_178a.c, ch9200.c and smsc75xx.c:
* If the drivers receive a link change interrupt immediately before
disconnect, they raise EVENT_LINK_RESET in their (non-sleepable)
->status() callback and schedule usbnet_deferred_kevent().
* usbnet_deferred_kevent() invokes the driver's ->link_reset() callback,
which calls netif_carrier_{on,off}().
* That in turn schedules the work linkwatch_event().
Because usbnet_deferred_kevent() is awaited after unregister_netdev(),
netif_carrier_{on,off}() may operate on an unregistered netdev and
linkwatch_event() may run after free_netdev(), causing a use-after-free.
In 2010, usbnet was changed to only wait for a single instance of
usbnet_deferred_kevent() instead of *all* work by commit 23f333a2bf
("drivers/net: don't use flush_scheduled_work()").
Unfortunately the commit neglected to move the wait back to
->ndo_stop(). Rectify that omission at long last.
Reported-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/netdev/CAG48ez0MHBbENX5gCdHAUXZ7h7s20LnepBF-pa5M=7Bi-jZrEA@mail.gmail.com/
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/netdev/20220315113841.GA22337@pengutronix.de/
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/d1c87ebe9fc502bffcd1576e238d685ad08321e4.1655987888.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc5250cdb4 upstream.
We won't really have enough skbs to need a 64-bit cookie,
and on 32-bit platforms storing the 64-bit cookie into the
void *rate_driver_data doesn't work anyway. Switch back to
using just a 32-bit cookie and uintptr_t for the type to
avoid compiler warnings about all this.
Fixes: 4ee186fa7e ("wifi: mac80211_hwsim: fix race condition in pending packet")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: Jeongik Cha <jeongik@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58b6259d82 upstream.
The robots report that we're now casting to a differently
sized integer, which is correct, and the previous patch
had erroneously removed it.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 4ee186fa7e ("wifi: mac80211_hwsim: fix race condition in pending packet")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: Jeongik Cha <jeongik@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ee186fa7e upstream.
A pending packet uses a cookie as an unique key, but it can be duplicated
because it didn't use atomic operators.
And also, a pending packet can be null in hwsim_tx_info_frame_received_nl
due to race condition with mac80211_hwsim_stop.
For this,
* Use an atomic type and operator for a cookie
* Add a lock around the loop for pending packets
Signed-off-by: Jeongik Cha <jeongik@google.com>
Link: https://lore.kernel.org/r/20220704084354.3556326-1-jeongik@google.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b3046abc9 upstream.
syzbot is reporting lockdep warning at ath9k_wmi_event_tasklet() followed
by kernel panic at get_htc_epid_queue() from ath9k_htc_tx_get_packet() from
ath9k_htc_txstatus() [1], for ath9k_wmi_event_tasklet(WMI_TXSTATUS_EVENTID)
depends on spin_lock_init() from ath9k_init_priv() being already completed.
Since ath9k_wmi_event_tasklet() is set by ath9k_init_wmi() from
ath9k_htc_probe_device(), it is possible that ath9k_wmi_event_tasklet() is
called via tasklet interrupt before spin_lock_init() from ath9k_init_priv()
from ath9k_init_device() from ath9k_htc_probe_device() is called.
Let's hold ath9k_wmi_event_tasklet(WMI_TXSTATUS_EVENTID) no-op until
ath9k_tx_init() completes.
Link: https://syzkaller.appspot.com/bug?extid=31d54c60c5b254d6f75b [1]
Reported-by: syzbot <syzbot+31d54c60c5b254d6f75b@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot <syzbot+31d54c60c5b254d6f75b@syzkaller.appspotmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/77b76ac8-2bee-6444-d26c-8c30858b8daa@i-love.sakura.ne.jp
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0ec7e55fc upstream.
syzbot is reporting lockdep warning followed by kernel panic at
ath9k_htc_rxep() [1], for ath9k_htc_rxep() depends on ath9k_rx_init()
being already completed.
Since ath9k_htc_rxep() is set by ath9k_htc_connect_svc(WMI_BEACON_SVC)
from ath9k_init_htc_services(), it is possible that ath9k_htc_rxep() is
called via timer interrupt before ath9k_rx_init() from ath9k_init_device()
is called.
Since we can't call ath9k_init_device() before ath9k_init_htc_services(),
let's hold ath9k_htc_rxep() no-op until ath9k_rx_init() completes.
Link: https://syzkaller.appspot.com/bug?extid=4d2d56175b934b9a7bf9 [1]
Reported-by: syzbot <syzbot+4d2d56175b934b9a7bf9@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot <syzbot+4d2d56175b934b9a7bf9@syzkaller.appspotmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/2b88f416-b2cb-7a18-d688-951e6dc3fe92@i-love.sakura.ne.jp
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 829eea7c94 upstream.
USB device ID of some versions of XiaoDu WiFi Dongle is 2955:1003
instead of 2955:1001. Both are the same mt7601u hardware.
Signed-off-by: Wei Mingzhi <whistler@member.fsf.org>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210618160840.305024-1-whistler@member.fsf.org
Cc: Yan Xinyu <sdlyyxy@bupt.edu.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 67c3b611d9 ]
Sending a PTP packet can imply to use the normal TX driver datapath but
invoked from the driver's ptp worker. The kernel generic TX code
disables softirqs and preemption before calling specific driver TX code,
but the ptp worker does not. Although current ptp driver functionality
does not require it, there are several reasons for doing so:
1) The invoked code is always executed with softirqs disabled for non
PTP packets.
2) Better if a ptp packet transmission is not interrupted by softirq
handling which could lead to high latencies.
3) netdev_xmit_more used by the TX code requires preemption to be
disabled.
Indeed a solution for dealing with kernel preemption state based on static
kernel configuration is not possible since the introduction of dynamic
preemption level configuration at boot time using the static calls
functionality.
Fixes: f79c957a0b ("drivers: net: sfc: use netdev_xmit_more helper")
Signed-off-by: Alejandro Lucero <alejandro.lucero-palau@amd.com>
Link: https://lore.kernel.org/r/20220726064504.49613-1-alejandro.lucero-palau@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a159128fa ]
We try using cancel_delayed_work_sync() to prevent the work from
enabling NAPI. This is insufficient since we don't disable the source
of the refill work scheduling. This means an NAPI poll callback after
cancel_delayed_work_sync() can schedule the refill work then can
re-enable the NAPI that leads to use-after-free [1].
Since the work can enable NAPI, we can't simply disable NAPI before
calling cancel_delayed_work_sync(). So fix this by introducing a
dedicated boolean to control whether or not the work could be
scheduled from NAPI.
[1]
==================================================================
BUG: KASAN: use-after-free in refill_work+0x43/0xd4
Read of size 2 at addr ffff88810562c92e by task kworker/2:1/42
CPU: 2 PID: 42 Comm: kworker/2:1 Not tainted 5.19.0-rc1+ #480
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Workqueue: events refill_work
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
print_report.cold+0xbb/0x6ac
? _printk+0xad/0xde
? refill_work+0x43/0xd4
kasan_report+0xa8/0x130
? refill_work+0x43/0xd4
refill_work+0x43/0xd4
process_one_work+0x43d/0x780
worker_thread+0x2a0/0x6f0
? process_one_work+0x780/0x780
kthread+0x167/0x1a0
? kthread_exit+0x50/0x50
ret_from_fork+0x22/0x30
</TASK>
...
Fixes: b2baed69e6 ("virtio_net: set/cancel work on ndo_open/ndo_stop")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fcbb71102 ]
Fix the inability to bring an interface up on a setup with
only MSI interrupts enabled (no MSI-X).
Solution is to add a default number of QPs = 1. This is enough,
since without MSI-X support driver enables only a basic feature set.
Fixes: bc6d33c8d9 ("i40e: Fix the number of queues available to be mapped for use")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220722175401.112572-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7b205fbbf ]
init_rx_sa() allocates relevant resource for rx_sa->stats and rx_sa->
key.tfm with alloc_percpu() and macsec_alloc_tfm(). When some error
occurs after init_rx_sa() is called in macsec_add_rxsa(), the function
released rx_sa with kfree() without releasing rx_sa->stats and rx_sa->
key.tfm, which will lead to a resource leak.
We should call macsec_rxsa_put() instead of kfree() to decrease the ref
count of rx_sa and release the relevant resource if the refcount is 0.
The same bug exists in macsec_add_txsa() for tx_sa as well. This patch
fixes the above two bugs.
Fixes: 3cf3227a21 ("net: macsec: hardware offloading infrastructure")
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c630d1fe62 ]
Currently, MACSEC_SA_ATTR_PN is handled inconsistently, sometimes as a
u32, sometimes forced into a u64 without checking the actual length of
the attribute. Instead, we can use nla_get_u64 everywhere, which will
read up to 64 bits into a u64, capped by the actual length of the
attribute coming from userspace.
This fixes several issues:
- the check in validate_add_rxsa doesn't work with 32-bit attributes
- the checks in validate_add_txsa and validate_upd_sa incorrectly
reject X << 32 (with X != 0)
Fixes: 48ef50fa86 ("macsec: Netlink support of XPN cipher suites (IEEE 802.1AEbw)")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b07a0e2044 ]
IEEE 802.1AEbw-2013 (section 10.7.8) specifies that the maximum value
of the replay window is 2^30-1, to help with recovery of the upper
bits of the PN.
To avoid leaving the existing macsec device in an inconsistent state
if this test fails during changelink, reuse the cleanup mechanism
introduced for HW offload. This wasn't needed until now because
macsec_changelink_common could not fail during changelink, as
modifying the cipher suite was not allowed.
Finally, this must happen after handling IFLA_MACSEC_CIPHER_SUITE so
that secy->xpn is set.
Fixes: 48ef50fa86 ("macsec: Netlink support of XPN cipher suites (IEEE 802.1AEbw)")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3240eac4ff ]
The expected length is MACSEC_SALT_LEN, not MACSEC_SA_ATTR_SALT.
Fixes: 48ef50fa86 ("macsec: Netlink support of XPN cipher suites (IEEE 802.1AEbw)")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f46040eeaf ]
Commit 48ef50fa86 added a test on tb_sa[MACSEC_SA_ATTR_PN], but
nothing guarantees that it's not NULL at this point. The same code was
added to macsec_add_txsa, but there it's not a problem because
validate_add_txsa checks that the MACSEC_SA_ATTR_PN attribute is
present.
Note: it's not possible to reproduce with iproute, because iproute
doesn't allow creating an SA without specifying the PN.
Fixes: 48ef50fa86 ("macsec: Netlink support of XPN cipher suites (IEEE 802.1AEbw)")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208315
Reported-by: Frantisek Sumsal <fsumsal@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebbbe23fdf ]
In bcm5421_init(), we should call of_node_put() for the reference
returned by of_get_parent() which has increased the refcount.
Fixes: 3c326fe9cb ("[PATCH] ppc64: Add new PHY to sungem")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220720131003.1287426-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cc019545a2 upstream.
Currently loopback test is failiing due to the error returned from
ice_vsi_vlan_setup(). Skip calling it when preparing loopback VSI.
Fixes: 0e674aeb0b ("ice: Add handler for ethtool selftest")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 283d736ff7 upstream.
Tx side sets EOP and RS bits on descriptors to indicate that a
particular descriptor is the last one and needs to generate an irq when
it was sent. These bits should not be checked on completion path
regardless whether it's the Tx or the Rx. DD bit serves this purpose and
it indicates that a particular descriptor is either for Rx or was
successfully Txed. EOF is also set as loopback test does not xmit
fragmented frames.
Look at (DD | EOF) bits setting in ice_lbtest_receive_frames() instead
of EOP and RS pair.
Fixes: 0e674aeb0b ("ice: Add handler for ethtool selftest")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36a15e1cb1 upstream.
The extra byte inserted by usbnet.c when
(length % dev->maxpacket == 0) is causing problems to device.
This patch sets FLAG_SEND_ZLP to avoid this.
Tested with: 0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet
Problems observed:
======================================================================
1) Using ssh/sshfs. The remote sshd daemon can abort with the message:
"message authentication code incorrect"
This happens because the tcp message sent is corrupted during the
USB "Bulk out". The device calculate the tcp checksum and send a
valid tcp message to the remote sshd. Then the encryption detects
the error and aborts.
2) NETDEV WATCHDOG: ... (ax88179_178a): transmit queue 0 timed out
3) Stop normal work without any log message.
The "Bulk in" continue receiving packets normally.
The host sends "Bulk out" and the device responds with -ECONNRESET.
(The netusb.c code tx_complete ignore -ECONNRESET)
Under normal conditions these errors take days to happen and in
intense usage take hours.
A test with ping gives packet loss, showing that something is wrong:
ping -4 -s 462 {destination} # 462 = 512 - 42 - 8
Not all packets fail.
My guess is that the device tries to find another packet starting
at the extra byte and will fail or not depending on the next
bytes (old buffer content).
======================================================================
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3666f666e9 ]
While reading these knobs, they can be changed concurrently.
Thus, we need to add READ_ONCE() to their readers.
- tcp_sack
- tcp_window_scaling
- tcp_timestamps
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7241f679a ]
be_cmd_read_port_transceiver_data assumes that it is given a buffer that
is at least PAGE_DATA_LEN long, or twice that if the module supports SFF
8472. However, this is not always the case.
Fix this by passing the desired offset and length to
be_cmd_read_port_transceiver_data so that we only copy the bytes once.
Fixes: e36edd9d26 ("be2net: add ethtool "-m" option support")
Signed-off-by: Hristo Venev <hristo@venev.name>
Link: https://lore.kernel.org/r/20220716085134.6095-1-hristo@venev.name
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f838a63369 ]
Fix an issue when driver incorrectly detects state
of recovery process and erroneously reinitializes interrupts,
which results in a kernel error and call trace message.
The issue was caused by a combination of two factors:
1. Assuming the EMP reset issued after completing
firmware recovery means the whole recovery process is complete.
2. Erroneous reinitialization of interrupt vector after detecting
the above mentioned EMP reset.
Fixes (1) by changing how recovery state change is detected
and (2) by adjusting the conditional expression to ensure using proper
interrupt reinitialization method, depending on the situation.
Fixes: 4ff0ee1af0 ("i40e: Introduce recovery mode support")
Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220715214542.2968762-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9f49e0060 ]
Fix memory leak caused by not handling dummy receive descriptor properly.
iavf_get_rx_buffer now sets the rx_buffer return value for dummy receive
descriptors. Without this patch, when the hardware writes a dummy
descriptor, iavf would not free the page allocated for the previous receive
buffer. This is an unlikely event but can still happen.
[Jesse: massaged commit message]
Fixes: efa14c3985 ("iavf: allow null RX descriptors")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4c7d8948e ]
Current stmmac driver will prepare/enable ptp_ref clock in
stmmac_init_tstamp_counter().
The stmmac_pltfr_noirq_suspend will disable it once in suspend flow.
But in resume flow,
stmmac_pltfr_noirq_resume --> stmmac_init_tstamp_counter
stmmac_resume --> stmmac_hw_setup --> stmmac_init_ptp --> stmmac_init_tstamp_counter
ptp_ref clock reference counter increases twice, which leads to unbalance
ptp clock when resume back.
Move ptp_ref clock prepare/enable out of stmmac_init_tstamp_counter to fix it.
Fixes: 0735e639f1 ("net: stmmac: skip only stmmac_ptp_register when resume from suspend")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bf9e18d9a ]
While reading sysctl_ip_fwd_update_priority, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 432e05d328 ("net: ipv4: Control SKB reprioritization after forwarding")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c1ddcee53 ]
The initially merged version of the igc driver code (via commit
146740f9ab, "igc: Add support for PF") contained the following
IGC_REMOVED checks in the igc_rd32/wr32() MMIO accessors:
u32 igc_rd32(struct igc_hw *hw, u32 reg)
{
u8 __iomem *hw_addr = READ_ONCE(hw->hw_addr);
u32 value = 0;
if (IGC_REMOVED(hw_addr))
return ~value;
value = readl(&hw_addr[reg]);
/* reads should not return all F's */
if (!(~value) && (!reg || !(~readl(hw_addr))))
hw->hw_addr = NULL;
return value;
}
And:
#define wr32(reg, val) \
do { \
u8 __iomem *hw_addr = READ_ONCE((hw)->hw_addr); \
if (!IGC_REMOVED(hw_addr)) \
writel((val), &hw_addr[(reg)]); \
} while (0)
E.g. igb has similar checks in its MMIO accessors, and has a similar
macro E1000_REMOVED, which is implemented as follows:
#define E1000_REMOVED(h) unlikely(!(h))
These checks serve to detect and take note of an 0xffffffff MMIO read
return from the device, which can be caused by a PCIe link flap or some
other kind of PCI bus error, and to avoid performing MMIO reads and
writes from that point onwards.
However, the IGC_REMOVED macro was not originally implemented:
#ifndef IGC_REMOVED
#define IGC_REMOVED(a) (0)
#endif /* IGC_REMOVED */
This led to the IGC_REMOVED logic to be removed entirely in a
subsequent commit (commit 3c215fb18e, "igc: remove IGC_REMOVED
function"), with the rationale that such checks matter only for
virtualization and that igc does not support virtualization -- but a
PCIe device can become detached even without virtualization being in
use, and without proper checks, a PCIe bus error affecting an igc
adapter will lead to various NULL pointer dereferences, as the first
access after the error will set hw->hw_addr to NULL, and subsequent
accesses will blindly dereference this now-NULL pointer.
This patch reinstates the IGC_REMOVED checks in igc_rd32/wr32(), and
implements IGC_REMOVED the way it is done for igb, by checking for the
unlikely() case of hw_addr being NULL. This change prevents the oopses
seen when a PCIe link flap occurs on an igc adapter.
Fixes: 146740f9ab ("igc: Add support for PF")
Signed-off-by: Lennert Buytenhek <buytenh@arista.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e5ec6a2513 upstream.
mlxsw needs to distinguish nexthops with a gateway from connected
nexthops in order to write the former to the adjacency table of the
device. The check used to rely on the fact that nexthops with a gateway
have a 'link' scope whereas connected nexthops have a 'host' scope. This
is no longer correct after commit 747c143072 ("ip: fix dflt addr
selection for connected nexthop").
Fix that by instead checking the address family of the gateway IP. This
is a more direct way and also consistent with the IPv6 counterpart in
mlxsw_sp_rt6_is_gateway().
Cc: stable@vger.kernel.org
Fixes: 747c143072 ("ip: fix dflt addr selection for connected nexthop")
Fixes: 597cfe4fc3 ("nexthop: Add support for IPv4 nexthops")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c6da4590fe ]
This reverts commit 05ca14fdb6.
On early silicon engineering samples observed bit shrinking issue when
we use brp as 1. Hence updated brp_min as 2. As in production silicon
this issue is fixed, so reverting the patch.
Link: https://lore.kernel.org/all/20220609082433.1191060-2-srinivas.neeli@xilinx.com
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a18d802d6 ]
sfp_probe() allocates a memory chunk from sfp with sfp_alloc(). When
devm_add_action() fails, sfp is not freed, which leads to a memory leak.
We should use devm_add_action_or_reset() instead of devm_add_action().
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20220629075550.2152003-1-niejianglei2021@163.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f33250760 ]
Below commit claims that atlantic NIC requires to reset the device on pm
op, and had set the deep to true for all suspend/resume functions.
commit 1809c30b6e ("net: atlantic: always deep reset on pm op, fixing up my null deref regression")
So, we could remove deep parameter on suspend/resume functions without
any functional change.
Fixes: 1809c30b6e ("net: atlantic: always deep reset on pm op, fixing up my null deref regression")
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Link: https://lore.kernel.org/r/20220713111224.1535938-1-acelan.kao@canonical.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ada74c5539 ]
When creating VFs a kernel panic can happen when calling to
efx_ef10_try_update_nic_stats_vf.
When releasing a DMA coherent buffer, sometimes, I don't know in what
specific circumstances, it has to unmap memory with vunmap. It is
disallowed to do that in IRQ context or with BH disabled. Otherwise, we
hit this line in vunmap, causing the crash:
BUG_ON(in_interrupt());
This patch reenables BH to release the buffer.
Log messages when the bug is hit:
kernel BUG at mm/vmalloc.c:2727!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 6 PID: 1462 Comm: NetworkManager Kdump: loaded Tainted: G I --------- --- 5.14.0-119.el9.x86_64 #1
Hardware name: Dell Inc. PowerEdge R740/06WXJT, BIOS 2.8.2 08/27/2020
RIP: 0010:vunmap+0x2e/0x30
...skip...
Call Trace:
__iommu_dma_free+0x96/0x100
efx_nic_free_buffer+0x2b/0x40 [sfc]
efx_ef10_try_update_nic_stats_vf+0x14a/0x1c0 [sfc]
efx_ef10_update_stats_vf+0x18/0x40 [sfc]
efx_start_all+0x15e/0x1d0 [sfc]
efx_net_open+0x5a/0xe0 [sfc]
__dev_open+0xe7/0x1a0
__dev_change_flags+0x1d7/0x240
dev_change_flags+0x21/0x60
...skip...
Fixes: d778819609 ("sfc: DMA the VF stats only when requested")
Reported-by: Ma Yuying <yuma@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20220713092116.21238-1-ihuguet@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebe41da5d4 ]
Use after free is detected by kfence when disabling sriov. What was read
after being freed was vf->pci_dev: it was freed from pci_disable_sriov
and later read in efx_ef10_sriov_free_vf_vports, called from
efx_ef10_sriov_free_vf_vswitching.
Set the pointer to NULL at release time to not trying to read it later.
Reproducer and dmesg log (note that kfence doesn't detect it every time):
$ echo 1 > /sys/class/net/enp65s0f0np0/device/sriov_numvfs
$ echo 0 > /sys/class/net/enp65s0f0np0/device/sriov_numvfs
BUG: KFENCE: use-after-free read in efx_ef10_sriov_free_vf_vswitching+0x82/0x170 [sfc]
Use-after-free read at 0x00000000ff3c1ba5 (in kfence-#224):
efx_ef10_sriov_free_vf_vswitching+0x82/0x170 [sfc]
efx_ef10_pci_sriov_disable+0x38/0x70 [sfc]
efx_pci_sriov_configure+0x24/0x40 [sfc]
sriov_numvfs_store+0xfe/0x140
kernfs_fop_write_iter+0x11c/0x1b0
new_sync_write+0x11f/0x1b0
vfs_write+0x1eb/0x280
ksys_write+0x5f/0xe0
do_syscall_64+0x5c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
kfence-#224: 0x00000000edb8ef95-0x00000000671f5ce1, size=2792, cache=kmalloc-4k
allocated by task 6771 on cpu 10 at 3137.860196s:
pci_alloc_dev+0x21/0x60
pci_iov_add_virtfn+0x2a2/0x320
sriov_enable+0x212/0x3e0
efx_ef10_sriov_configure+0x67/0x80 [sfc]
efx_pci_sriov_configure+0x24/0x40 [sfc]
sriov_numvfs_store+0xba/0x140
kernfs_fop_write_iter+0x11c/0x1b0
new_sync_write+0x11f/0x1b0
vfs_write+0x1eb/0x280
ksys_write+0x5f/0xe0
do_syscall_64+0x5c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
freed by task 6771 on cpu 12 at 3170.991309s:
device_release+0x34/0x90
kobject_cleanup+0x3a/0x130
pci_iov_remove_virtfn+0xd9/0x120
sriov_disable+0x30/0xe0
efx_ef10_pci_sriov_disable+0x57/0x70 [sfc]
efx_pci_sriov_configure+0x24/0x40 [sfc]
sriov_numvfs_store+0xfe/0x140
kernfs_fop_write_iter+0x11c/0x1b0
new_sync_write+0x11f/0x1b0
vfs_write+0x1eb/0x280
ksys_write+0x5f/0xe0
do_syscall_64+0x5c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 3c5eb87605 ("sfc: create vports for VFs and assign random MAC addresses")
Reported-by: Yanghang Liu <yanghliu@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20220712062642.6915-1-ihuguet@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49b9f431ff ]
In ftgmac100_probe(), we should hold the refernece returned by
of_get_child_by_name() and use it to call of_node_put() for
reference balance.
Fixes: 39bfab8844 ("net: ftgmac100: Add support for DT phy-handle property")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 029c1c2059 ]
There is a long-standing issue with the Synopsys DWC Ethernet driver
for Tegra194 where random system crashes have been observed [0]. The
problem occurs when the split header feature is enabled in the stmmac
driver. In the bad case, a larger than expected buffer length is
received and causes the calculation of the total buffer length to
overflow. This results in a very large buffer length that causes the
kernel to crash. Why this larger buffer length is received is not clear,
however, the feedback from the NVIDIA design team is that the split
header feature is not supported for Tegra194. Therefore, disable split
header support for Tegra194 to prevent these random crashes from
occurring.
[0] https://lore.kernel.org/linux-tegra/b0b17697-f23e-8fa5-3757-604a86f3a095@nvidia.com/
Fixes: 67afd6d1cf ("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20220706083913.13750-1-jonathanh@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 452133dd58 ]
The existing capability check for vnic env counters only checks for
receive steering discards, although we need the counters update for the
exposed internal queue oob counter as well. This could result in the
latter counter not being updated correctly when the receive steering
discards counter is not supported.
Fix that by checking whether any counter is supported instead of only
the steering counter capability.
Fixes: 0cfafd4b4d ("net/mlx5e: Add device out of buffer counter")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cc2714e85 ]
Use the correct constant (TLS_DRIVER_STATE_SIZE_TX) in the comparison
against the size of the private TX TLS driver context.
Fixes: df8d866770 ("net/mlx5e: kTLS, Use kernel API to extract private offload context")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faa4e04e5e ]
66e4c8d950 ("net: warn if transport header was not set") added
a check that triggers a warning in r8169, see [0].
The commit referenced in the Fixes tag refers to the change from
which the patch applies cleanly, there's nothing wrong with this
commit. It seems the actual issue (not bug, because the warning
is harmless here) was introduced with bdfa4ed681
("r8169: use Giant Send").
[0] https://bugzilla.kernel.org/show_bug.cgi?id=216157
Fixes: 8d520b4de3 ("r8169: work around RTL8125 UDP hw bug")
Reported-by: Erhard F. <erhard_f@mailbox.org>
Tested-by: Erhard F. <erhard_f@mailbox.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/1b2c2b29-3dc0-f7b6-5694-97ec526d51a0@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b18f09d31 ]
During a reset, there may have been transmits in flight that are no
longer valid and cannot be fulfilled. Resetting and clearing the
queues is insufficient; each skb also needs to be explicitly freed
so that upper levels are not left waiting for confirmation of a
transmit that will never happen. If this happens frequently enough,
the apparent backlog will cause TCP to begin "congestion control"
unnecessarily, culminating in permanently decreased throughput.
Fixes: d7c0ef36bd ("ibmvnic: Free and re-allocate scrqs when tx/rx scrqs change")
Tested-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Rick Lindsley <ricklind@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
