commit 01d4503968 upstream.
For usec delays use udelay instead of scheduling, this should
allow reclocking to happen faster. This also was the cause
of reported 33s delays at bootup on certain systems.
fixes: freedesktop.org bug 25506
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b9241ea31f upstream.
When we setup buffer for display plane, we'll check any pending
required GPU flush and possible make interruptible wait for flush
complete. But that wait would be most possibly to fail in case of
signals received for X process, which will then fail modeset process
and put display engine in unconsistent state. The result could be
blank screen or CPU hang, and DDX driver would always turn on outputs
DPMS after whatever modeset fails or not.
So this one creates new helper for setup display plane buffer, and
when needing flush using uninterruptible wait for that.
This one should fix bug like https://bugs.freedesktop.org/show_bug.cgi?id=24009.
Also fixing mode switch stress test on Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 48764bf43f upstream.
This just waits until the hw passed the current ring position with
cmd execution. This slightly changes the existing i915_wait_request
function to make uninterruptible waiting possible - no point in
returning to userspace while mucking around with the overlay, that
piece of hw is just too fragile.
Also replace a magic 0 with the symbolic constant (and kill the then
superflous comment) while I was looking at the code.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 823f68fd64 upstream.
This one reverts 9e3a6d155e.
As reported by http://bugzilla.kernel.org/show_bug.cgi?id=14485,
this dump will cause hang problem on some machine. If something
really needs this kind of full registers dump, that could be done
within intel-gpu-tools.
Cc: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 99fcb766a3 upstream.
Before changing the status of a buffer with a pending write we will await
upon a new flush for that buffer. So we can take advantage of any flushes
posted whilst the buffer is active and pending processing by the GPU, by
clearing its write_domain and updating its last_rendering_seqno -- thus
saving a potential flush in deep queues and improves flushing behaviour
upon eviction for both GTT space and fences.
In order to reduce the time spent searching the active list for matching
write_domains, we move those to a separate list whose elements are
the buffers belong to the active/flushing list with pending writes.
Orignal patch by Chris Wilson <chris@chris-wilson.co.uk>, forward-ported
by me.
In addition to better performance, this also fixes a real bug. Before
this changes, i915_gem_evict_everything didn't work as advertised. When
the gpu was actually busy and processing request, the flush and subsequent
wait would not move active and dirty buffers to the inactive list, but
just to the flushing list. Which triggered the BUG_ON at the end of this
function. With the more tight dirty buffer tracking, all currently busy and
dirty buffers get moved to the inactive list by one i915_gem_flush operation.
I've left the BUG_ON I've used to prove this in there.
References:
Bug 25911 - 2.10.0 causes kernel oops and system hangs
http://bugs.freedesktop.org/show_bug.cgi?id=25911
Bug 26101 - [i915] xf86-video-intel 2.10.0 (and git) triggers kernel oops
within seconds after login
http://bugs.freedesktop.org/show_bug.cgi?id=26101
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Adam Lantos <hege@playma.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit fd2e8ea597 upstream.
An untiled framebuffer must be aligned to 64k. This is normally handled
by intel_pin_and_fence_fb_obj(), but the intelfb_create() likes to be
different and do the pinning itself. However, it aligns the buffer
object incorrectly for pre-i965 chipsets causing a PGTBL_ERR when it is
installed onto the output.
Fixes:
KMS error message while initializing modesetting -
render error detected: EIR: 0x10 [i915]
http://bugs.freedesktop.org/show_bug.cgi?id=22936
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ee25df2bc3 upstream.
On 945, we need to avoid entering self-refresh if the compressor is
busy, or we may cause display FIFO underruns leading to ugly flicker.
Fixes fdo bug #24314, kernel bug #15043.
Tested-by: Alexander Lam <lambchop468@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Julien Cristau <jcristau@debian.org> (fd.o #25371)
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit a3cb5195f6 upstream.
The MALATA PC-81005 laptop always reports that the LID status is closed and we
can't use it reliabily for LVDS detection. So add this box into the quirk list.
https://bugs.freedesktop.org/show_bug.cgi?id=25523
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Review-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Hector <hector1987@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 40f33a9210 upstream.
The HP comaq nx9020/Samsung SX20S laptop always report that the LID status is
closed and we can't use it reliabily for LVDS detection. So add the two boxes
into the quirk list.
http://bugzilla.kernel.org/show_bug.cgi?id=14957http://bugzilla.kernel.org/show_bug.cgi?id=14554
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit f0217c42c9 upstream.
This is a sync of a fix I made in the old UMS code. If the BIOS uses
the GMBUS and doesn't clear that setup, then our bit-banging I2C can
fail, leading to monitors not being detected.
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 33c5fd121e upstream.
Self Refresh should be disabled on dual plane configs. Otherwise, as
the SR watermark is not calculated for such configs, switching to non
VGA mode causes FIFO underrun and display flicker.
This fixes Korg Bug #14897.
Signed-off-by: David John <davidjon@xenontk.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1dc7546d1a upstream.
Need to calculate the SR watermark and enable it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit eceb784cec upstream.
This tries to fix CRT detect loop hang seen on some Ironlake form
factor, to clear up hotplug detect state before taking CRT detect
to make sure next hotplug detect cycle is consistent.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b01f2c3a4a upstream.
This patch changes around our hotplug enable code a bit to only enable
it for ports we actually detect and initialize. This prevents problems
with stuck or spurious interrupts on outputs that aren't actually wired
up, and is generally more correct.
Fixes FDO bug #23183.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c566ec4915 upstream.
Make sure hangcheck timer won't beat us unexpectedly on Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 4bdadb9785 upstream.
Having missed the ENOMEM return via i915_gem_fault(), there are probably
other paths that I also missed. By not enabling NORETRY by default these
paths can run the shrinker and take memory from the system (but not from
our own inactive lists because our shrinker can not run whilst we hold
the struct mutex) and this may allow the system to survive a little longer
whilst our drivers consume all available memory.
References:
OOM killer unexpectedly called with kernel 2.6.32
http://bugzilla.kernel.org/show_bug.cgi?id=14933
v2: Pass gfp into page mapping.
v3: Use new read_cache_page_gfp() instead of open-coding.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 7c3f0a2726 upstream.
There exist multiple DDC buses for the SDVO cards with multiple outputs.
When we can't get the EDID by using the select DDC bus, we can try the other
possible DDC bus to see whether the EDID can be obtained.
https://bugs.freedesktop.org/show_bug.cgi?id=23842
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 6a304caf0b upstream.
For some SDVO cards based on conexant chip, we can't read the EDID if
we don't read the response after issuing SDVO DDC bus switch
command.
From the SDVO spec once when another I2C transaction is finished after
completing the I2C transaction of issuing the bus switch command, it
will be switched back to the SDVO internal state again. So we can't
initiate a new I2C transaction to read the response after issuing the
DDC bus switch command. Instead we should issue DDC bus switch command
and read the response in the same I2C transaction.
https://bugs.freedesktop.org/show_bug.cgi?id=23842https://bugs.freedesktop.org/show_bug.cgi?id=24458https://bugs.freedesktop.org/show_bug.cgi?id=24522https://bugs.freedesktop.org/show_bug.cgi?id=24282
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c7c85101af upstream.
On Ironlake, there is an interrupt master control bit. With the bit
disabled before clearing IIR, we do not need to handle extra interrupt
in a loop. This patch removes the loop in Ironlake interrupt handler.
It fixed irq lost issue on some Ironlake platforms.
Signed-off-by: Zou Nan hai <Nanhai.zou@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit cda9d05c49 upstream.
This code generally fails to adjust the render clock, and when it does,
it conflicts with some other register settings and can cause problems.
So remove this code altogether. I'm reworking it now to do the right
thing, but the only bit it will share is the VBT check for whether
reclocking is supported, so I'm leaving that bit.
Reverts most of 652c393a33 ("add dynamic
clock frequency control"), though for many the regressions showed up
in the later 181a5336d6 ("Fix render
reclock availability detection").
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 29bd0ae25f upstream.
drivers/gpu/drm/i915/i915_dma.c: In function 'i915_driver_load':
drivers/gpu/drm/i915/i915_dma.c:1114: warning: 'll_base' may be used uninitialized in this function
Partly this is because gcc isn't smart enough. But `ll_base' does get used
uninitialised in the DRM_DEBUG() call.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit e5a95eb778 upstream.
Select the correct BPC for LVDS on Ironlake. If it is 18-bit LVDS panel,
the BPC will be 6. When it is 24-bit LVDS panel, the BPC will 8.
At the same time the BPC will be 8 when the output device is CRT/HDMI/DP.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 8faf3b3174 upstream.
Make the BPC in FDI rx/transcoder be consistent with that in pipeconf on Ironlake.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 898822ce95 upstream.
Enable/disable the dithering for LVDS based on VBT setting. On the 965/g4x
platform the dithering flag is defined in LVDS register. And on the ironlake
the dithering flag is defined in pipeconf register.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit e6be8d9d17 upstream.
drm_pci_alloc() has input of address mask for setting pci dma
mask on the device, which should be properly setup by drm driver.
And leave it as a param for drm_pci_alloc() would cause confusion
or mistake would corrupt the correct dma mask setting, as seen on
intel hw which set wrong dma mask for hw status page. So remove
it from drm_pci_alloc() function.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit e3d8affb0d upstream.
As pinning (allocating and binding GTT memory) does not actually invoke
GPU commands, it is safe, and indeed is attempted, during resumption
from suspension:
[drm:intel_init_clock_gating] *ERROR* failed to pin power context: -16
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 96b47b6559 upstream.
i915_gem_object_unbind had the ordering wrong. The other user,
i915_gem_object_put_fence_reg already has the correct ordering.
Results was usually corrupted pixmaps, especially garbled font glyphs
after a suspend/resume (because this evicts everything).
I'm still waiting for the feedback from the bug-reporters, but
because this obviously fixes a bug (at least for me) I'm already
submitting it.
Bugzilla: http://bugs.freedesktop.org/show_bug.cgi?id=25406
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit a2565377a5 upstream.
Dirk reports that nothing is displayed on LVDS when using ubuntu 9.1 after
close/reopen the LID. And I also reproduce this issue on another laptop.
After some tests and debug, it seems that it is related with that the
LVDS status is not updated in time in course of suspend/resume.
Now the LID state is used to check whether the LVDS is connected or
disconnected. And when the LID is closed, it means that the LVDS is
disconnected. When it is reopened, it means that the LVDS is connected.
At the same time on some distributions the LID event is also used to put
the system into suspend state. When the LID is closed, the system will enter
the suspend state. When the LID is reopened, the system will be resumed.
In such case when the LID is closed, user-space script will receive the LID
notification event and detect the LVDS as disconnected. Then the system will
enter the suspended state. When the LID is reopened, the system will be
resumed. As the LVDS status is not updated in course of resume, it will cause
that the LVDS connector is marked as unused and disabled. After the resume is
finished,user-space script will try to configure the display mode for LVDS.
But unfortunately as the LVDS status is not updated in time and it is still
marked as disconnected, the LVDS and its corresponding CRTC will be disabled
again in the function of drm_helper_disable_unused_functions after changing
mode for LVDS.
So we had better check and update the status of LVDS connector after receiving
the LID notication event. Then after the system is resumed from suspended
state, we can set the display mode for LVDS correctly.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reported-by: Dirk Hohndel <hohndel@infradead.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b16d9acbdb upstream.
Sometimes we will use a crtc for integerated LVDS, which is different with
that assigned by BIOS. If we want to get flicker-free transitions,
then we could read out the current state for it and set our current state
accordingly.
But it is true that if we aren't reading current state out, we do need
to turn everything off before modesetting. Otherwise the clocks can get very
angry and we get things worse than a flicker at boot.
In fact we also do the similar thing in UMS mode. We will disable all the
possible outputs/crtcs for the first modesetting.
So we disable all the possible outputs/crtcs before entering the KMS mode.
Before we configure connector/encoder/crtc, the function of
drm_helper_disable_unused_function can disable all the possible outputs/crtcs.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Rafal Milecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In 2.6.32.2 r600 had no IRQ support, however the patch in
500b758725 to fix vblanks on avivo
cards, needs irqs.
So check for an R600 card and avoid this path if so.
This is a stable only patch for 2.6.32.2 as 2.6.33 has IRQs for r600.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 794f3141a1 upstream.
drivers/gpu/drm/radeon/radeon_test.c:45: undefined reference to `__udivdi3'
Reported-by: Mr. James W. Laferriere <babydr@baby-dragons.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1b3c7a47f9 upstream.
In disable sequence, all output ports on PCH have to be disabled
before PCH transcoder, but LVDS port was left always enabled. This
one fixes that by disable LVDS port properly during pipe disable
process, and resolved stability issue seen on Ironlake. Also move
panel fitting disable time just after pipe disable to align with
the spec.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 103a196f42 upstream.
PineView only has 2 ports for LVDS and CRT. Don't enable other
ports for it.
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit d271817bae upstream.
In commit d2d9f2324, the guard for a valid video mode was removed. This
caused the regression:
kernel crash during kms graphic boot on Intel GM4500 platform
https://bugzilla.redhat.com/show_bug.cgi?id=540218
This patches changes the logic slightly not to rely on a coupled
variable, but to just check whether the video_modes is valid before
dereferencing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Zhenyu Wang <zhenyu.z.wang@intel.com>
[ickle: Actually reference the correct bug report]
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 778c902640 upstream
In current vblank-wait implementation, if we turn off VGA output,
drm_wait_vblank will still wait on the disabled pipe until timeout,
because vblank on the pipe is assumed be enabled. This would cause
slow system response on some system such as moblin.
This patch resolve the issue by adding a drm helper function
drm_vblank_off which explicitly clear vblank_enabled[crtc], wake up
any waiting queue and save last vblank counter before turning off
crtc. It also slightly change drm_vblank_get to ensure that we will
will return immediately if trying to wait on a disabled pipe.
Signed-off-by: Li Peng <peng.li@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: hand-applied for conflicts with overlay changes]
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 652af9d74e upstream.
Add the missing clonemask for display port on Ironlake.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 5618ca6abc upstream.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 722f29434e upstream.
also fix up rs690 mem width.
should fix fdo bug 25408
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 4e3f9b78ff upstream.
Board is DVI+VGA, not DVI+DVI
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver requires shmfs as the backing filesystem to handle the buffer
objects, so ensure it is selected if the user chooses to build our
driver.
Fixes: Bug 14662 - Dell E5500 kernel panic with KMS
http://bugzilla.kernel.org/show_bug.cgi?id=14662
The revealing nature of the panic is the NULL function pointer
dereference in read_cache_page_async().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Mateusz Kaduk <mateusz.kaduk@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: stable@kernel.org
For CRT hotplug detect status, we have four test results as blue
channel only, green channel only, both blue and green channel, and
no channel attached. Origin code only marks both blue and green channel
case as connected, but ignore other possible connected states. This one
trys to detect CRT by checking no channel attached case instead.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When the framebuffer driver does not publish detailed timing information
for the current video mode, the correct value for the pixclock field is
zero, not -1.
Since pixclock is actually unsigned, the value -1 would be interpreted
as 4294967295 picoseconds (i.e., about 4 milliseconds) by
register_framebuffer() and userspace programs.
This patch allows X.org's fbdev driver to work.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some architectures compute ->vm_page_prot depending on ->vm_flags, so we
need to update the protections after adjusting the flags.
AFAIK this only affects running X under Xen; without this patch you get
lots of coloured blobs on the screen, or maybe a complete lockup. Or
anything really.
But that still depends on lots of out-of-tree stuff, so I don't think
there are any consequences for anyone else. But it is wrong in principle.
Reported-by: Jan Beulich <JBeulich@novell.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On broken EDID we were reporting vga connector to be disconnected
even if ddc probe did found a monitor. This patch report that the
connector is connected on such case. This allow drm to add a fail
safe mode (800x600 at the time of this patch) thus user can boot
and later add a mode which match its monitor capabilities.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
unused_nodes modification needs to be protected by unused_lock spinlock.
Here is an example of an usage where there is no such protection without
this patch.
Process 1: 1-drm_mm_pre_get(this function modify unused_nodes list)
2-spin_lock(spinlock protecting mm struct)
3-drm_mm_put_block(this function might modify unused_nodes
list but doesn't protect modification with unused_lock)
4-spin_unlock(spinlock protecting mm struct)
Process2: 1-drm_mm_pre_get(this function modify unused_nodes list)
At this point Process1 & Process2 might both be doing modification to
unused_nodes list. This patch add unused_lock protection into
drm_mm_put_block to avoid such issue.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
