x86 has no flush_tlb_range support in instruction level. Currently the
flush_tlb_range just implemented by flushing all page table. That is not
the best solution for all scenarios. In fact, if we just use 'invlpg' to
flush few lines from TLB, we can get the performance gain from later
remain TLB lines accessing.
But the 'invlpg' instruction costs much of time. Its execution time can
compete with cr3 rewriting, and even a bit more on SNB CPU.
So, on a 512 4KB TLB entries CPU, the balance points is at:
(512 - X) * 100ns(assumed TLB refill cost) =
X(TLB flush entries) * 100ns(assumed invlpg cost)
Here, X is 256, that is 1/2 of 512 entries.
But with the mysterious CPU pre-fetcher and page miss handler Unit, the
assumed TLB refill cost is far lower then 100ns in sequential access. And
2 HT siblings in one core makes the memory access more faster if they are
accessing the same memory. So, in the patch, I just do the change when
the target entries is less than 1/16 of whole active tlb entries.
Actually, I have no data support for the percentage '1/16', so any
suggestions are welcomed.
As to hugetlb, guess due to smaller page table, and smaller active TLB
entries, I didn't see benefit via my benchmark, so no optimizing now.
My micro benchmark show in ideal scenarios, the performance improves 70
percent in reading. And in worst scenario, the reading/writing
performance is similar with unpatched 3.4-rc4 kernel.
Here is the reading data on my 2P * 4cores *HT NHM EP machine, with THP
'always':
multi thread testing, '-t' paramter is thread number:
with patch unpatched 3.4-rc4
./mprotect -t 1 14ns 24ns
./mprotect -t 2 13ns 22ns
./mprotect -t 4 12ns 19ns
./mprotect -t 8 14ns 16ns
./mprotect -t 16 28ns 26ns
./mprotect -t 32 54ns 51ns
./mprotect -t 128 200ns 199ns
Single process with sequencial flushing and memory accessing:
with patch unpatched 3.4-rc4
./mprotect 7ns 11ns
./mprotect -p 4096 -l 8 -n 10240
21ns 21ns
[ hpa: http://lkml.kernel.org/r/1B4B44D9196EFF41AE41FDA404FC0A100BFF94@SHSMSX101.ccr.corp.intel.com
has additional performance numbers. ]
Signed-off-by: Alex Shi <alex.shi@intel.com>
Link: http://lkml.kernel.org/r/1340845344-27557-3-git-send-email-alex.shi@intel.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This reverts commit c074da2810.
This change has several unwanted side effects:
1) Sockets will cache the DST_NOCACHE route in sk->sk_rx_dst and we'll
thus never create a real cached route.
2) All TCP traffic will use DST_NOCACHE and never use the routing
cache at all.
Signed-off-by: David S. Miller <davem@davemloft.net>
1. removed code replication for tov calculation for 1G, 10G and
made is common for speed > 1G (1G, 10G, 40G, 100G).
2. defines values for #4 different 40G Phys (KR4, LF4, SR4, CR4)
Signed-off-by: Parav Pandit <parav.pandit@emulex.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes all RTA_GET*() and RTA_PUT*() variations, as well as the
the unused rtattr_strcmp(). Get rid of rtm_get_table() by moving
it to its only user decnet.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
DDOS synflood attacks hit badly IP route cache.
On typical machines, this cache is allowed to hold up to 8 Millions dst
entries, 256 bytes for each, for a total of 2GB of memory.
rt_garbage_collect() triggers and tries to cleanup things.
Eventually route cache is disabled but machine is under fire and might
OOM and crash.
This patch exploits the new TCP early demux, to set a nocache
boolean in case incoming TCP frame is for a not yet ESTABLISHED or
TIMEWAIT socket.
This 'nocache' boolean is then used in case dst entry is not found in
route cache, to create an unhashed dst entry (DST_NOCACHE)
SYN-cookie-ACK sent use a similar mechanism (ipv4: tcp: dont cache
output dst for syncookies), so after this patch, a machine is able to
absorb a DDOS synflood attack without polluting its IP route cache.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some small USB gadget bugfixes, and a few new USB device ids added to
some drivers for the 3.5-rc5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/rYS0ACgkQMUfUDdst+ynuGQCfYYD43H+BtubcS+jt5N61/5lM
wUgAoM1wru64Kfox9v6U8g21AnLeJOhJ
=e1xG
-----END PGP SIGNATURE-----
Merge tag 'usb-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are some small USB gadget bugfixes, and a few new USB device ids
added to some drivers for the 3.5-rc5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: CP210x Add 10 Device IDs
USB: option: Add USB ID for Novatel Ovation MC551
usb: phy: Fix Kconfig dependency for Phy drivers
usb-storage: revert commit afff07e61a (Add 090c:1000 to unusal-devs)
SCSI & usb-storage: add try_rc_10_first flag
usb: musb: host: release dma channels if no active io
usb: gadget: lpc32xx_udc: fix build error with debugfs enabled
usb: otg: twl6030-usb: Fix twl writes
USB: option: add id for Cellient MEN-200
usb: dwc3: fix giveback of queued request in ep_dequeue
usb: gadget: Complete fsl qe/udc driver conversion
Some of them are BCM4706 specific AFAWK. Most of them was confirmed on
Netgear WNDR450.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is a cleanup.
It adds nf_ct_kfree_compat_sysctl_table to release l4proto's
compat sysctl table and set the compat sysctl table point to NULL.
This new function will be used by follow-up patches.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
l4proto->init contain quite redundant code. We can simplify this
by adding a new parameter l3proto.
This patch prepares that code simplification.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When CONFIG_PM is disabled, no device can possibly
support WoWLAN since it can't go to sleep to start
with. Due to this, mac80211 had even rejected the
hardware registration. By making all the code and
data for WoWLAN depend on CONFIG_PM we can promote
this runtime error to a compile-time error.
Add #ifdef around all WoWLAN code to remove it in
systems that don't need it as they never suspend.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds the following messages to ctnetlink:
IPCTNL_MSG_CT_GET_STATS_CPU
IPCTNL_MSG_CT_GET_STATS
IPCTNL_MSG_EXP_GET_STATS_CPU
To display connection tracking system per-cpu and global statistics.
This provides a replacement for the following /proc interfaces:
/proc/net/stat/nf_conntrack
/proc/sys/net/netfilter/nf_conntrack_count
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In order to test if the error counters are properly incremented,
add a way to specify how many errors were generated by a trace.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* v4l_for_linus: (44 commits)
[media] smia: Fix compile failures
[media] Fix VIDIOC_DQEVENT docbook entry
[media] s5p-fimc: Fix control creation function
[media] s5p-mfc: Fix checkpatch error in s5p_mfc_shm.h file
[media] s5p-mfc: Fix setting controls
[media] v4l/s5p-mfc: added image size align in VIDIOC_TRY_FMT
[media] v4l/s5p-mfc: corrected encoder v4l control definitions
[media] v4l: mem2mem_testdev: Fix race conditions in driver
[media] s5p-mfc: Bug fix of timestamp/timecode copy mechanism
[media] cxd2820r: Fix an incorrect modulation type bitmask
[media] em28xx: Show a warning if the board does not support remote controls
[media] em28xx: Add remote control support for Terratec's Cinergy HTC Stick HD
[media] USB: Staging: media: lirc: initialize spinlocks before usage
[media] Revert "[media] media: mx2_camera: Fix mbus format handling"
[media] bw-qcam: driver and pixfmt documentation fixes
[media] cx88: fix firmware load on big-endian systems
[media] cx18: support big-endian systems
[media] ivtv: fix support for big-endian systems
[media] tuner-core: return the frequency range of the correct tuner
[media] v4l2-dev.c: fix g_parm regression in determine_valid_ioctls()
...
Conflicts:
Documentation/DocBook/media/v4l/vidioc-create-bufs.xml
drivers/media/video/em28xx/em28xx-cards.c
The AT86RF231 is a feature rich, low-power 2.4 GHz radio transceiver
designed for industrial and consumer ZigBee/IEEE 802.15.4, 6LoWPAN,
RF4CE and high data rate 2.4 GHz ISM band applications.
This patch adds support for the Atmel RF230/231 radio transceivers.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every real 802.15.4 transceiver, which works with software MAC layer,
can be classified as a wpan device in this stack. So the wpan device
implementation provides missing link in datapath between the device
drivers and the Linux network queue.
According to the IEEE 802.15.4 standard each packet can be one of the
following types:
- beacon
- MAC layer command
- ACK
- data
This patch adds support for the data packet-type only, but this is
enough to perform data transmission and receiving over radio.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (as1562) cleans up the definitions of the EHCI extended
registers to be consistent with the definitions of the standard
registers. This makes the code look a lot nicer, with no functional
change.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, request_queue has one request_list to allocate requests
from regardless of blkcg of the IO being issued. When the unified
request pool is used up, cfq proportional IO limits become meaningless
- whoever grabs the next request being freed wins the race regardless
of the configured weights.
This can be easily demonstrated by creating a blkio cgroup w/ very low
weight, put a program which can issue a lot of random direct IOs there
and running a sequential IO from a different cgroup. As soon as the
request pool is used up, the sequential IO bandwidth crashes.
This patch implements per-blkg request_list. Each blkg has its own
request_list and any IO allocates its request from the matching blkg
making blkcgs completely isolated in terms of request allocation.
* Root blkcg uses the request_list embedded in each request_queue,
which was renamed to @q->root_rl from @q->rq. While making blkcg rl
handling a bit harier, this enables avoiding most overhead for root
blkcg.
* Queue fullness is properly per request_list but bdi isn't blkcg
aware yet, so congestion state currently just follows the root
blkcg. As writeback isn't aware of blkcg yet, this works okay for
async congestion but readahead may get the wrong signals. It's
better than blkcg completely collapsing with shared request_list but
needs to be improved with future changes.
* After this change, each block cgroup gets a full request pool making
resource consumption of each cgroup higher. This makes allowing
non-root users to create cgroups less desirable; however, note that
allowing non-root users to directly manage cgroups is already
severely broken regardless of this patch - each block cgroup
consumes kernel memory and skews IO weight (IO weights are not
hierarchical).
v2: queue-sysfs.txt updated and patch description udpated as suggested
by Vivek.
v3: blk_get_rl() wasn't checking error return from
blkg_lookup_create() and may cause oops on lookup failure. Fix it
by falling back to root_rl on blkg lookup failures. This problem
was spotted by Rakesh Iyer <rni@google.com>.
v4: Updated to accomodate 458f27a982 "block: Avoid missed wakeup in
request waitqueue". blk_drain_queue() now wakes up waiters on all
blkg->rl on the target queue.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, all of the architectures implement their own pcibios_setup()
routine. Most of the implementations do nothing so this patch introduces
a generic (__weak) routine in the core that can be used by all
architectures as a default. If necessary, it can be overridden by
architecture-specific code.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Support configuring an RSSI threshold in dBm (s32) when requesting
scheduled scan, below which a BSS won't be reported by the cfg80211
driver.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove use of module parameters on caif hsi device, as
rtnl configuration parameters are already supported.
All caif hsi configuration data is put in cfhsi_config,
and default values in hsi_default_config.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove use of struct platform_device, and replace it with
struct cfhsi_ops. Updated variable names in the same
spirit:
cfhsi_get_dev to cfhsi_get_ops,
cfhsi->dev to cfhsi->ops and,
cfhsi->dev.drv to cfhsi->ops->cb_ops.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RTNL support for managing the caif hsi interface.
The HSI HW interface is no longer registering as a device,
instead we use symbol_get to get hold of the HSI API.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing kernel doc for sk_rx_dst
Move sk_rx_dst to avoid two 32bit holes on 64bit arches
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With early demux enabled by default for TCP flows, there is high chance that
skb->sk will be non-null. 'unlikely()' was removed from __inet_lookup_skb() but
maybe it can be removed from skb_steal_sock() as well.
Note: skb_steal_sock() is also called by __inet6_lookup_skb() and
__udp4_lib_lookup_skb() but they are protected by their own 'unlikely' calls.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull media fixes from Mauro Carvalho Chehab.
Trivial conflict due to new USB HID ID's being added next to each other
(Baanto vs Axentia).
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (44 commits)
[media] smia: Fix compile failures
[media] Fix VIDIOC_DQEVENT docbook entry
[media] s5p-fimc: Fix control creation function
[media] s5p-mfc: Fix checkpatch error in s5p_mfc_shm.h file
[media] s5p-mfc: Fix setting controls
[media] v4l/s5p-mfc: added image size align in VIDIOC_TRY_FMT
[media] v4l/s5p-mfc: corrected encoder v4l control definitions
[media] v4l: mem2mem_testdev: Fix race conditions in driver
[media] s5p-mfc: Bug fix of timestamp/timecode copy mechanism
[media] cxd2820r: Fix an incorrect modulation type bitmask
[media] em28xx: Show a warning if the board does not support remote controls
[media] em28xx: Add remote control support for Terratec's Cinergy HTC Stick HD
[media] USB: Staging: media: lirc: initialize spinlocks before usage
[media] Revert "[media] media: mx2_camera: Fix mbus format handling"
[media] bw-qcam: driver and pixfmt documentation fixes
[media] cx88: fix firmware load on big-endian systems
[media] cx18: support big-endian systems
[media] ivtv: fix support for big-endian systems
[media] tuner-core: return the frequency range of the correct tuner
[media] v4l2-dev.c: fix g_parm regression in determine_valid_ioctls()
...
Add task management support, wind up in abort and device reset error
handlers. Cancel all in-flight urbs in bus reset handler.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make it possible for gpio-ir-recv users to choose a map name.
Cc: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 2603efa31a ("bug.h: Fix up powerpc build regression") corrected
the powerpc build case and extended the __ASSEMBLY__ guards, but it also
got caught in pre-processor hell accidentally matching the else case of
CONFIG_BUG resulting in the BUG disabled case tripping up on
-Werror=implicit-function-declaration.
It's not possible to __ASSEMBLY__ guard the entire file as architecture
code needs to get at the BUGFLAG_WARNING definition in the GENERIC_BUG
case, but the rest of the CONFIG_BUG=y/n case needs to be guarded.
Rather than littering endless __ASSEMBLY__ checks in each of the if/else
cases we just move the BUGFLAG definitions up under their own
GENERIC_BUG test and then shove everything else under one big
__ASSEMBLY__ guard.
Build tested on all of x86 CONFIG_BUG=y, CONFIG_BUG=n, powerpc (due to
it's dependence on BUGFLAG definitions in assembly code), and sh (due to
not bringing in linux/kernel.h to satisfy the taint flag definitions used
by the generic bug code).
Hopefully that's the end of the corner cases and I can abstain from ever
having to touch this infernal header ever again.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Fengguang Wu <wfg@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP53AxAAoJEHm+PkMAQRiGs2QH/RaqkXz96fwjhDcyiKpDqA3c
kGuS5mz5cOhnqKSmR88HFm6pwuhLux/qSJzeAmoQy1MC8a0ACx7AnANW0lfN3/qe
/HGYz8h60yCL/fhn8/bUYtdt9xsoDqoDcq/ooFl9mcsJGWbC6WeMSZU5dAUYqviE
qFrp5zjY07FG53CRGT0hFpezQNwNL+VLH30CF9LD+fJLPVEYum2zBNGXWM42rcw5
fxzGL/6SO8YqA/Upic1ht6HAd6s5LOrlST7qvnyXUMvRXN5z/Y92ueYJZefkS1Om
ohuLIKM2bv9/dJS67H8N2baSKGCzBdfSe5/5WaHdLYW9MiVju0wRl6HPJtAMrkk=
=H8t8
-----END PGP SIGNATURE-----
Merge tag 'v3.5-rc4' into drm-intel-next-queued
I want to merge the "no more fake agp on gen6+" patches into
drm-intel-next (well, the last pieces). But a patch in 3.5-rc4 also
adds a new use of dev->agp. Hence the backmarge to sort this out, for
otherwise drm-intel-next merged into Linus' tree would conflict in the
relevant code, things would compile but nicely OOPS at driver load :(
Conflicts in this merge are just simple cases of "both branches
changed/added lines at the same place". The only tricky part is to
keep the order correct wrt the unwind code in case of errors in
intel_ringbuffer.c (and the MI_DISPLAY_FLIP #defines in i915_reg.h
together, obviously).
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_ringbuffer.c
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This picks up the staging changes made in 3.5-rc4 so that everyone can sync up
properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to get the USB fixes that were merged in the 3.5-rc4 tree into usb-next
so that everyone can sync up properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed to sync up with the previous USB changes that were merged in
Linus's branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code was based on:
"arch/microblaze/kernel/prom_parse.c"
"arch/powerpc/kernel/prom_parse.c"
Can replace "of_parse_dma_window()" in the above. This supports
different formats flexibly. "prefix" can be configured if any. "busno"
and "index" are optionally specified. Set NULL and 0 if not used.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
IOMMU device groups are currently a rather vague associative notion
with assembly required by the user or user level driver provider to
do anything useful. This patch intends to grow the IOMMU group concept
into something a bit more consumable.
To do this, we first create an object representing the group, struct
iommu_group. This structure is allocated (iommu_group_alloc) and
filled (iommu_group_add_device) by the iommu driver. The iommu driver
is free to add devices to the group using it's own set of policies.
This allows inclusion of devices based on physical hardware or topology
limitations of the platform, as well as soft requirements, such as
multi-function trust levels or peer-to-peer protection of the
interconnects. Each device may only belong to a single iommu group,
which is linked from struct device.iommu_group. IOMMU groups are
maintained using kobject reference counting, allowing for automatic
removal of empty, unreferenced groups. It is the responsibility of
the iommu driver to remove devices from the group
(iommu_group_remove_device).
IOMMU groups also include a userspace representation in sysfs under
/sys/kernel/iommu_groups. When allocated, each group is given a
dynamically assign ID (int). The ID is managed by the core IOMMU group
code to support multiple heterogeneous iommu drivers, which could
potentially collide in group naming/numbering. This also keeps group
IDs to small, easily managed values. A directory is created under
/sys/kernel/iommu_groups for each group. A further subdirectory named
"devices" contains links to each device within the group. The iommu_group
file in the device's sysfs directory, which formerly contained a group
number when read, is now a link to the iommu group. Example:
$ ls -l /sys/kernel/iommu_groups/26/devices/
total 0
lrwxrwxrwx. 1 root root 0 Apr 17 12:57 0000:00:1e.0 ->
../../../../devices/pci0000:00/0000:00:1e.0
lrwxrwxrwx. 1 root root 0 Apr 17 12:57 0000:06:0d.0 ->
../../../../devices/pci0000:00/0000:00:1e.0/0000:06:0d.0
lrwxrwxrwx. 1 root root 0 Apr 17 12:57 0000:06:0d.1 ->
../../../../devices/pci0000:00/0000:00:1e.0/0000:06:0d.1
$ ls -l /sys/kernel/iommu_groups/26/devices/*/iommu_group
[truncating perms/owner/timestamp]
/sys/kernel/iommu_groups/26/devices/0000:00:1e.0/iommu_group ->
../../../kernel/iommu_groups/26
/sys/kernel/iommu_groups/26/devices/0000:06:0d.0/iommu_group ->
../../../../kernel/iommu_groups/26
/sys/kernel/iommu_groups/26/devices/0000:06:0d.1/iommu_group ->
../../../../kernel/iommu_groups/26
Groups also include several exported functions for use by user level
driver providers, for example VFIO. These include:
iommu_group_get(): Acquires a reference to a group from a device
iommu_group_put(): Releases reference
iommu_group_for_each_dev(): Iterates over group devices using callback
iommu_group_[un]register_notifier(): Allows notification of device add
and remove operations relevant to the group
iommu_group_id(): Return the group number
This patch also extends the IOMMU API to allow attaching groups to
domains. This is currently a simple wrapper for iterating through
devices within a group, but it's expected that the IOMMU API may
eventually make groups a more integral part of domains.
Groups intentionally do not try to manage group ownership. A user
level driver provider must independently acquire ownership for each
device within a group before making use of the group as a whole.
This may change in the future if group usage becomes more pervasive
across both DMA and IOMMU ops.
Groups intentionally do not provide a mechanism for driver locking
or otherwise manipulating driver matching/probing of devices within
the group. Such interfaces are generic to devices and beyond the
scope of IOMMU groups. If implemented, user level providers have
ready access via iommu_group_for_each_dev and group notifiers.
iommu_device_group() is removed here as it has no users. The
replacement is:
group = iommu_group_get(dev);
id = iommu_group_id(group);
iommu_group_put(group);
AMD-Vi & Intel VT-d support re-added in following patches.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
IOMMU groups allow IOMMU drivers to represent DMA visibility
and isolation of devices. Multiple devices may be grouped
together for the purposes of DMA. Placing a pointer on
struct device enable easy access for things like streaming
DMA programming and drivers like VFIO.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The atomic notifier from twl4030/twl6030 to notifiy VBUS and ID events,
is replaced by a direct call to omap musb blue.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Used devres API's to associate the phy with a device so that on
driver detach, release function is invoked on the devres data(usb_phy)
and devres data(usb_phy) is released.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a linked list for keeping multiple PHY instances with different
types so that we can have separate USB2 and USB3 PHYs on one single
board. _get_phy_ has been changed so that the controller gets
the transceiver by type. _remove_phy_ has been added to let the phy
be removed from the phy list.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
_transceiver() in otg.c is replaced with _phy. usb_set_transceiver is
replaced with usb_add_phy to make it similar to other usb standard
function names like usb_add_hcd.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Request allocation is about to be made per-blkg meaning that there'll
be multiple request lists.
* Make queue full state per request_list. blk_*queue_full() functions
are renamed to blk_*rl_full() and takes @rl instead of @q.
* Rename blk_init_free_list() to blk_init_rl() and make it take @rl
instead of @q. Also add @gfp_mask parameter.
* Add blk_exit_rl() instead of destroying rl directly from
blk_release_queue().
* Add request_list->q and make request alloc/free functions -
blk_free_request(), [__]freed_request(), __get_request() - take @rl
instead of @q.
This patch doesn't introduce any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add q->nr_rqs[] which currently behaves the same as q->rq.count[] and
move q->rq.elvpriv to q->nr_rqs_elvpriv. blk_drain_queue() is updated
to use q->nr_rqs[] instead of q->rq.count[].
These counters separates queue-wide request statistics from the
request list and allow implementation of per-queue request allocation.
While at it, properly indent fields of struct request_list.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
iscsi_remove_host() uses bsg_remove_queue() which implements custom
queue draining. fc_bsg_remove() open-codes mostly identical logic.
The draining logic isn't correct in that blk_stop_queue() doesn't
prevent new requests from being queued - it just stops processing, so
nothing prevents new requests to be queued after the logic determines
that the queue is drained.
blk_cleanup_queue() now implements proper queue draining and these
custom draining logics aren't necessary. Drop them and use
bsg_unregister_queue() + blk_cleanup_queue() instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: James Smart <james.smart@emulex.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
mempool_create_node() currently assumes %GFP_KERNEL. Its only user,
blk_init_free_list(), is about to be updated to use other allocation
flags - add @gfp_mask argument to the function.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP53AxAAoJEHm+PkMAQRiGs2QH/RaqkXz96fwjhDcyiKpDqA3c
kGuS5mz5cOhnqKSmR88HFm6pwuhLux/qSJzeAmoQy1MC8a0ACx7AnANW0lfN3/qe
/HGYz8h60yCL/fhn8/bUYtdt9xsoDqoDcq/ooFl9mcsJGWbC6WeMSZU5dAUYqviE
qFrp5zjY07FG53CRGT0hFpezQNwNL+VLH30CF9LD+fJLPVEYum2zBNGXWM42rcw5
fxzGL/6SO8YqA/Upic1ht6HAd6s5LOrlST7qvnyXUMvRXN5z/Y92ueYJZefkS1Om
ohuLIKM2bv9/dJS67H8N2baSKGCzBdfSe5/5WaHdLYW9MiVju0wRl6HPJtAMrkk=
=H8t8
-----END PGP SIGNATURE-----
Merge tag 'v3.5-rc4' into regulator-drivers
Linux 3.5-rc4 contains patches which conflict with some of the
development work.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP53AxAAoJEHm+PkMAQRiGs2QH/RaqkXz96fwjhDcyiKpDqA3c
kGuS5mz5cOhnqKSmR88HFm6pwuhLux/qSJzeAmoQy1MC8a0ACx7AnANW0lfN3/qe
/HGYz8h60yCL/fhn8/bUYtdt9xsoDqoDcq/ooFl9mcsJGWbC6WeMSZU5dAUYqviE
qFrp5zjY07FG53CRGT0hFpezQNwNL+VLH30CF9LD+fJLPVEYum2zBNGXWM42rcw5
fxzGL/6SO8YqA/Upic1ht6HAd6s5LOrlST7qvnyXUMvRXN5z/Y92ueYJZefkS1Om
ohuLIKM2bv9/dJS67H8N2baSKGCzBdfSe5/5WaHdLYW9MiVju0wRl6HPJtAMrkk=
=H8t8
-----END PGP SIGNATURE-----
Merge tag 'v3.5-rc4' into for-3.6
Linux 3.5-rc4 contains some bug fixes which overlap with new features.
Pull drm fixes from Dave Airlie:
"Nothing major in here, one radeon SI fix for tiling, and one uninit
var fix, two minor header file fixes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: drop comment about this header being autogenerated.
drm/edid: don't return stack garbage from supports_rb
vga_switcheroo: Add include guard
drm/radeon: SI tiling fixes for display
There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
* a lot of messages should be pr_info, not pr_debug
* wholesale use of pr_debug makes it require *both*
Kconfig and dynamic configuration
* there are still a lot of ifdefs
* the style is very inconsistent, sometimes the
sdata->name is printed in front
Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pablo says:
====================
The following four patches provide Netfilter fixes for the cthelper
infrastructure that was recently merged mainstream, they are:
* two fixes for compilation breakage with two different configurations:
- CONFIG_NF_NAT=m and CONFIG_NF_CT_NETLINK=y
- NF_CONNTRACK_EVENTS=n and CONFIG_NETFILTER_NETLINK_QUEUE_CT=y
* two fixes for sparse warnings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* topic/huang-d3cold-v7:
PCI/PM: add PCIe runtime D3cold support
PCI: do not call pci_set_power_state with PCI_D3cold
PCI/PM: add runtime PM support to PCIe port
ACPI/PM: specify lowest allowed state for device sleep state
This patch adds runtime D3cold support and corresponding ACPI platform
support. This patch only enables runtime D3cold support; it does not
enable D3cold support during system suspend/hibernate.
D3cold is the deepest power saving state for a PCIe device, where its main
power is removed. While it is in D3cold, you can't access the device at
all, not even its configuration space (which is still accessible in D3hot).
Therefore the PCI PM registers can not be used to transition into/out of
the D3cold state; that must be done by platform logic such as ACPI _PR3.
To support wakeup from D3cold, a system may provide auxiliary power, which
allows a device to request wakeup using a Beacon or the sideband WAKE#
signal. WAKE# is usually connected to platform logic such as ACPI GPE.
This is quite different from other power saving states, where devices
request wakeup via a PME message on the PCIe link.
Some devices, such as those in plug-in slots, have no direct platform
logic. For example, there is usually no ACPI _PR3 for them. D3cold
support for these devices can be done via the PCIe Downstream Port leading
to the device. When the PCIe port is powered on/off, the device is powered
on/off too. Wakeup events from the device will be notified to the
corresponding PCIe port.
For more information about PCIe D3cold and corresponding ACPI support,
please refer to:
- PCI Express Base Specification Revision 2.0
- Advanced Configuration and Power Interface Specification Revision 5.0
[bhelgaas: changelog]
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Originally-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Lower device sleep state can save more power, but has more exit
latency too. Sometimes, to satisfy some power QoS and other
requirement, we need to constrain the lowest device sleep state.
In this patch, a parameter to specify lowest allowed state for
acpi_pm_device_sleep_state is added. So that the caller can enforce
the constraint via the parameter.
This is needed by PCIe D3cold support, where the lowest power state
allowed may be D3_HOT instead of default D3_COLD.
CC: Len Brown <lenb@kernel.org>
CC: linux-acpi@vger.kernel.org
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Several forthcoming Wolfson devices are based on a common platform
known as Arizona allowing a great deal of reuse of driver code. This
patch adds core support for these devices.
In order to handle systems which do not use the generic clock API a
simple wrapper for the 32kHz clock domain in the devices is provided.
Once the generic clock API is widely available this code will be moved
over to use that.
For simplicity some WM5102 specific code is included in the core driver,
the effort involved in splitting the device out isn't worth it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Several forthcoming Wolfson devices are based on a common platform
known as Arizona allowing a great deal of reuse of driver code. This
patch adds register definitions for these devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The code handles this fine already, we just need new macros in the header
for drivers to create the controls.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This patch implements the spdif IN driver for ST peripheral
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Several bug reports have been received recently for USB mass-storage
devices that don't handle READ CAPACITY(16) commands properly. They
report bogus sizes, in some cases becoming unusable as a result.
The bugs were triggered by commit
09b6b51b0b (SCSI & usb-storage: add
flags for VPD pages and REPORT LUNS), which caused usb-storage to stop
overriding the SCSI level reported by devices. By default, the sd
driver will try READ CAPACITY(16) first for any device whose level is
above SCSI_SPC_2.
It seems likely that any device large enough to require the use of
READ CAPACITY(16) (i.e., 2 TB or more) would be able to handle READ
CAPACITY(10) commands properly. Indeed, I don't know of any devices
that don't handle READ CAPACITY(10) properly.
Therefore this patch (as1559) adds a new flag telling the sd driver
to try READ CAPACITY(10) before READ CAPACITY(16), and sets this flag
for every USB mass-storage device. If a device really is larger than
2 TB, sd will fall back to READ CAPACITY(16) just as it used to.
This fixes Bugzilla #43391.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't cache output dst for syncookies, as this adds pressure on IP route
cache and rcu subsystem for no gain.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to add a control for disabling early socket demux.
The main motivation behind this patch is to provide an option to disable
the feature as it adds an additional cost to routing that reduces overall
throughput by up to 5%. For example one of my systems went from 12.1Mpps
to 11.6 after the early socket demux was added. It looks like the reason
for the regression is that we are now having to perform two lookups, first
the one for an established socket, and then the one for the routing table.
By adding this patch and toggling the value for ip_early_demux to 0 I am
able to get back to the 12.1Mpps I was previously seeing.
[ Move local variables in ip_rcv_finish() down into the basic
block in which they are actually used. -DaveM ]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* topic/jiang-mmconfig-v10:
ACPI: mark acpi_sfi_table_parse() as __init
x86/PCI: use pr_level() to replace printk(KERN_LEVEL)
x86/PCI: refine __pci_mmcfg_init() for better code readability
x86/PCI: get rid of redundant log messages
x86/PCI: simplify pci_mmcfg_late_insert_resources()
x86/PCI: update MMCONFIG information when hot-plugging PCI host bridges
PCI/ACPI: provide MMCONFIG address for PCI host bridges
x86/PCI: add pci_mmconfig_insert()/delete() for PCI root bridge hotplug
x86/PCI: prepare pci_mmcfg_check_reserved() to be called at runtime
x86/PCI: introduce pci_mmcfg_arch_map()/pci_mmcfg_arch_unmap()
x86/PCI: use RCU list to protect mmconfig list
x86/PCI: split out pci_mmconfig_alloc() for code reuse
x86/PCI: split out pci_mmcfg_check_reserved() for code reuse
Mark function acpi_sfi_table_parse() as __init to avoid warning messages:
WARNING: vmlinux.o(.text+0x4cd2d2): Section mismatch in reference from the
function acpi_sfi_table_parse.clone.0() to the function
Function acpi_sfi_table_parse() calls acpi_table_parse() and
pci_parse_mcfg(), which are both marked as __init. Currently
acpi_sfi_table_parse() is only used by MMCONFIG to scan MCFG table
at boot time only, so it's safe to mark acpi_sfi_table_parse() as __init.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch provide MMCONFIG address for PCI host bridges, which will
be used to support host bridge hotplug. It gets MMCONFIG address
by evaluating _CBA method if available.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull perf updates from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ftrace: Make all inline tags also include notrace
perf: Use css_tryget() to avoid propping up css refcount
perf tools: Fix synthesizing tracepoint names from the perf.data headers
perf stat: Fix default output file
perf tools: Fix endianity swapping for adds_features bitmask
These are no longer used. Every ceph_connection instance is embedded in
another structure, and refcounts manipulated via the get/put ops.
Signed-off-by: Sage Weil <sage@inktank.com>
This patch add support for the SPEAr ASoC pcm layer in ASoC
framework. The pcm layer uses common snd_dmaengine framework.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add support for synopsys I2S controller as per the ASoC
framework.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
LD init/built-in.o
net/built-in.o:(.data+0x4408): undefined reference to `nf_nat_tcp_seq_adjust'
make: *** [vmlinux] Error 1
This patch adds a new pointer hook (nfq_ct_nat_hook) similar to other existing
in Netfilter to solve our complicated configuration dependencies.
Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fixes include:
- Fix a write hang due to an uninitalised variable when !defined(CONFIG_NFS_V4)
- Address upcall races in the legacy NFSv4 idmapper
- Remove an O_DIRECT refcounting issue
- Fix a pNFS refcounting bug when the file layout metadata server is also
acting as a data server
- Fix a pNFS module loading race.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=uEPz
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.5-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fix a write hang due to an uninitalised variable when
!defined(CONFIG_NFS_V4)
- Address upcall races in the legacy NFSv4 idmapper
- Remove an O_DIRECT refcounting issue
- Fix a pNFS refcounting bug when the file layout metadata server is
also acting as a data server
- Fix a pNFS module loading race.
* tag 'nfs-for-3.5-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Force the legacy idmapper to be single threaded
NFS: Initialise commit_info.rpc_out when !defined(CONFIG_NFS_V4)
NFS: Fix a refcounting issue in O_DIRECT
NFSv4.1: Fix a race in set_pnfs_layoutdriver
NFSv4.1: Fix umount when filelayout DS is also the MDS
Get current rssi (in dBm) from the driver/FW.
Instead of reporting the signal received in the last
rx packet, which might be inaccurate if rx traffic is
low and beacon filtering is enabled, get the signal
from the driver/FW.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This lets us catch the USB fixes that went into 3.5-rc3 into this branch,
as we want them here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Registering the platform driver before module_init allows us to log oopses
that happen during device probing.
This requires changing module_init to postcore_initcall, and switching
from platform_driver_probe to platform_driver_register because the
platform device is not registered when the platform driver is registered;
and because we use driver_register, now can't use create_bundle() (since
it will try to register the same driver once again), so we have to switch
to platform_device_register_data().
Also, some __init -> __devinit changes were needed.
Overall, the registration logic is now much clearer, since we have only
one driver registration point, and just an optional dummy device, which
is created from the module parameters.
Suggested-by: Colin Cross <ccross@android.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a number of small fixes for the drivers/staging tree, as well as iio
and pstore drivers (which came from the staging tree in the 3.5-rc1 merge).
All of these are tiny, but resolve issues that people have been reporting.
There's also a documentation update to reflect what the iio drivers really are
doing, which is good to get straightened out.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNeAACgkQMUfUDdst+ynNVwCdHCj6smC2JUbvN34gACNrpsYY
WggAoJzQn9mQhwq0pa/ZTpaUOvCFZ39L
=hDkC
-----END PGP SIGNATURE-----
Merge tag 'staging-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg Kroah-Hartman:
"Here are a number of small fixes for the drivers/staging tree, as well
as iio and pstore drivers (which came from the staging tree in the
3.5-rc1 merge). All of these are tiny, but resolve issues that people
have been reporting.
There's also a documentation update to reflect what the iio drivers
really are doing, which is good to get straightened out.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8712u: Add new USB IDs
staging: gdm72xx: Release netlink socket properly
iio: drop wrong reference from Kconfig
pstore/inode: Make pstore_fill_super() static
pstore/ram: Should zap persistent zone on unlink
pstore/ram_core: Factor persistent_ram_zap() out of post_init()
pstore/ram_core: Do not reset restored zone's position and size
pstore/ram: Should update old dmesg buffer before reading
staging:iio:ad7298: Fix linker error due to missing IIO kfifo buffer
Revert "staging: usbip: bugfix for stack corruption on 64-bit architectures"
staging: usbip: bugfix for stack corruption on 64-bit architectures
staging/comedi: fix build for USB not enabled
staging: omapdrm: fix crash when freeing bad fb
staging:iio:ad7606: Re-add missing scale attribute
iio: Fix potential use after free
staging:iio: remove num_interrupt_lines from documentation
iio: documentation: Add out_altvoltage and friends
Here are some fixes for 3.5-rc4 that resolve the kmsg problems that
people have reported showing up after the printk and kmsg changes went
into 3.5-rc1. There are also a smattering of other tiny fixes for the
extcon and hyper-v drivers that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNQcACgkQMUfUDdst+yklTQCfZCXFlhA43bZo/8Joqd2pLIIW
2uoAoMze0SlfJeN6Qu7yY0P+qV/f/pc3
=UNFY
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and printk fixes from Greg Kroah-Hartman:
"Here are some fixes for 3.5-rc4 that resolve the kmsg problems that
people have reported showing up after the printk and kmsg changes went
into 3.5-rc1. There are also a smattering of other tiny fixes for the
extcon and hyper-v drivers that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
extcon: max8997: Add missing kfree for info->edev in max8997_muic_remove()
extcon: Set platform drvdata in gpio_extcon_probe() and fix irq leak
extcon: Fix wrong index in max8997_extcon_cable[]
kmsg - kmsg_dump() fix CONFIG_PRINTK=n compilation
printk: return -EINVAL if the message len is bigger than the buf size
printk: use mutex lock to stop syslog_seq from going wild
kmsg - kmsg_dump() use iterator to receive log buffer content
vme: change maintainer e-mail address
Extcon: Don't try to create duplicate link names
driver core: fixup reversed deferred probe order
printk: Fix alignment of buf causing crash on ARM EABI
Tools: hv: verify origin of netlink connector message
* emailed from Andrew Morton <akpm@linux-foundation.org>: (21 patches)
mm/memblock: fix overlapping allocation when doubling reserved array
c/r: prctl: Move PR_GET_TID_ADDRESS to a proper place
pidns: find_new_reaper() can no longer switch to init_pid_ns.child_reaper
pidns: guarantee that the pidns init will be the last pidns process reaped
fault-inject: avoid call to random32() if fault injection is disabled
Viresh has moved
get_maintainer: Fix --help warning
mm/memory.c: fix kernel-doc warnings
mm: fix kernel-doc warnings
mm: correctly synchronize rss-counters at exit/exec
mm, thp: print useful information when mmap_sem is unlocked in zap_pmd_range
h8300: use the declarations provided by <asm/sections.h>
h8300: fix use of extinct _sbss and _ebss
xtensa: use the declarations provided by <asm/sections.h>
xtensa: use "test -e" instead of bashism "test -a"
xtensa: replace xtensa-specific _f{data,text} by _s{data,text}
memcg: fix use_hierarchy css_is_ancestor oops regression
mm, oom: fix and cleanup oom score calculations
nilfs2: ensure proper cache clearing for gc-inodes
thp: avoid atomic64_read in pmd_read_atomic for 32bit PAE
...
viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with viresh.linux@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the x86 32bit PAE CONFIG_TRANSPARENT_HUGEPAGE=y case while holding the
mmap_sem for reading, cmpxchg8b cannot be used to read pmd contents under
Xen.
So instead of dealing only with "consistent" pmdvals in
pmd_none_or_trans_huge_or_clear_bad() (which would be conceptually
simpler) we let pmd_none_or_trans_huge_or_clear_bad() deal with pmdvals
where the low 32bit and high 32bit could be inconsistent (to avoid having
to use cmpxchg8b).
The only guarantee we get from pmd_read_atomic is that if the low part of
the pmd was found null, the high part will be null too (so the pmd will be
considered unstable). And if the low part of the pmd is found "stable"
later, then it means the whole pmd was read atomically (because after a
pmd is stable, neither MADV_DONTNEED nor page faults can alter it anymore,
and we read the high part after the low part).
In the 32bit PAE x86 case, it is enough to read the low part of the pmdval
atomically to declare the pmd as "stable" and that's true for THP and no
THP, furthermore in the THP case we also have a barrier() that will
prevent any inconsistent pmdvals to be cached by a later re-read of the
*pmd.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On arches that do not support this_cpu_cmpxchg_double() slab_lock is used
to do atomic cmpxchg() on double word which contains page->_count. The
page count can be changed from get_page() or put_page() without taking
slab_lock. That corrupts page counter.
Fix it by moving page->_count out of cmpxchg_double data. So that slub
does no change it while updating slub meta-data in struct page.
[akpm@linux-foundation.org: use standard comment layout, tweak comment text]
Reported-by: Amey Bhide <abhide@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The encoding is tightly packed, and future changes (such as
pinconf-generic support) can easily lead to a situation where we violate
the encoding constraints and trample data bit/reg bits. This plugs in
some sanity checks by way of a BUILD_BUG_ON() to blow up if we fail to
fit.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently the sound dmaengine pcm helper functions implement the pcm_pointer
callback by trying to count the number of elapsed periods. This is done by
advancing the stream position in the dmaengine callback by one period.
Unfortunately there is no guarantee that the callback will be called for each
elapsed period. It may be possible that under high system load it is only called
once for multiple elapsed periods. This patch addresses the issue by
implementing support for querying the current stream position directly from the
dmaengine driver. Since not all dmaengine drivers support reporting the stream
position yet the old period counting implementation is kept for now.
Furthermore the new mechanism allows to report the stream position with a
sub-period granularity, given that the dmaengine driver supports this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the sound dmaengine pcm helper functions implement the pcm_pointer
callback by trying to count the number of elapsed periods. This is done by
advancing the stream position in the dmaengine callback by one period.
Unfortunately there is no guarantee that the callback will be called for each
elapsed period. It may be possible that under high system load it is only called
once for multiple elapsed periods. This patch renames the current implementation
and documents its shortcomings and that it should not be used anymore in new
drivers.
The next patch will introduce a new snd_dmaengine_pcm_pointer which will be
implemented based on querying the current stream position from the dma device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a small inline wrapper for the devivce_tx_status callback of a
dma device. This makes the source code of users of this function a bit more
compact and a bit more legible.
E.g.:
-status = chan->device->device_tx_status(chan, cookie, &state)
+status = dmaengine_tx_status(chan, cookie, &state)
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a small inline wrapper for the devivce_tx_status callback of a
dma device. This makes the source code of users of this function a bit more
compact and a bit more legible.
E.g.:
-status = chan->device->device_tx_status(chan, cookie, &state)
+status = dmaengine_tx_status(chan, cookie, &state)
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This implements a bit of rework for the PFC code, making the core itself
slightly more pluggable and moving out the gpio chip handling completely.
The API is preserved in such a way that platforms that depend on it for
early configuration are still able to do so, while making it possible to
migrate to alternate interfaces going forward.
This is the first step of chainsawing necessary to support the pinctrl
API, with the eventual goal being able to decouple pin function state
from the gpio API while retaining gpio chip tie-in for gpio pin functions
only, relying on the pinctrl/pinmux API for non-gpio function demux.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
slab_node() could access current->mempolicy from interrupt context.
However there's a race condition during exit where the mempolicy
is first freed and then the pointer zeroed.
Using this from interrupts seems bogus anyways. The interrupt
will interrupt a random process and therefore get a random
mempolicy. Many times, this will be idle's, which noone can change.
Just disable this here and always use local for slab
from interrupts. I also cleaned up the callers of slab_node a bit
which always passed the same argument.
I believe the original mempolicy code did that in fact,
so it's likely a regression.
v2: send version with correct logic
v3: simplify. fix typo.
Reported-by: Arun Sharma <asharma@fb.com>
Cc: penberg@kernel.org
Cc: cl@linux.com
Signed-off-by: Andi Kleen <ak@linux.intel.com>
[tdmackey@twitter.com: Rework control flow based on feedback from
cl@linux.com, fix logic, and cleanup current task_struct reference]
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Christoph Lameter <cl@linux.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: David Mackey <tdmackey@twitter.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
This file has been superseded by include/sound/ac97_codec.h,
and has currently no users.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most of changes are fairly small and driver-specific.
A remaining regression fix for USB-audio sync pipe check, a fix for
HD-audio power-up sequence, fixes for ASoC pxa-ssp compile issues, and
bunch of ASoC codec and trivial fix patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=oQ5N
-----END PGP SIGNATURE-----
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Most of changes are fairly small and driver-specific.
A remaining regression fix for USB-audio sync pipe check, a fix for
HD-audio power-up sequence, fixes for ASoC pxa-ssp compile issues, and
bunch of ASoC codec and trivial fix patches."
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: 6fire: use NULL instead of 0 for pointer assignment
ALSA: hda - Handle open while transitioning to D3.
ALSA: snd-usb: make snd_usb_substream_capture_trigger static
ALSA: snd-usb: fix sync pipe check
ASoC: tegra+wm8903: turn of mic detect when card is removed
ASoC: wm8996: Mark the CODEC as cache only when powering off on boot
ASoC: wm8996: Move reset before the initial regulator disable
ASoC: wm8996: Remove spurious regulator_bulk_free()
ASoC: wm8904: Fix cache only management
ASoC: wm8904: Fix GPIO and MICBIAS initialisation for regmap conversion
ASoC: fix pxa-ssp compiling issue under mach-mmp
ARM: MMP: add pxa910-ssp into ssp_id_table
Input packet processing for local sockets involves two major demuxes.
One for the route and one for the socket.
But we can optimize this down to one demux for certain kinds of local
sockets.
Currently we only do this for established TCP sockets, but it could
at least in theory be expanded to other kinds of connections.
If a TCP socket is established then it's identity is fully specified.
This means that whatever input route was used during the three-way
handshake must work equally well for the rest of the connection since
the keys will not change.
Once we move to established state, we cache the receive packet's input
route to use later.
Like the existing cached route in sk->sk_dst_cache used for output
packets, we have to check for route invalidations using dst->obsolete
and dst->ops->check().
Early demux occurs outside of a socket locked section, so when a route
invalidation occurs we defer the fixup of sk->sk_rx_dst until we are
actually inside of established state packet processing and thus have
the socket locked.
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows a voltage and current (bb_uvolts and bb_uamps) to be
specified in the platform_data, and charging of the backup battery will
be enabled with those specification.
As it is not possible to monitor the backup battery at all there is no
new device created to represent it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Don't pretend that inet_protos[] and inet6_protos[] are hashes, thay
are just a straight arrays. Remove all unnecessary hash masking.
Document MAX_INET_PROTOS.
Use RAW_HTABLE_SIZE when appropriate.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Constant Charge Current(CC) is charging parameter which limit the
maximum current which can be pumped into the battery during charge cycle.
Constant Charge Voltage(CV) is also charging parameter which limit the
maximum voltage that battery can reach during charge cycle.
It is very common practice that at low or high temperatures we
do not charge the batteries upto it's fullest charge voltage
to avoid battery and user safety issues.
These sysfs properties will be useful for debug and to implement
certain user space policies like "Charging limited due to OverTemp".
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
After converstion to SPARSE_IRQ, the driver doesn't use the
pdata->irq_base/irq_end fields anymore. The last users
have been cleanup up, and now these fields can be removed.
Cc: Benoit Cousson <b-cousson@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Trivially extend the regulator_register_always_on() helper function to be
even more useful by adding a voltage parameter to it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently regulator_register_fixed() uses a constant name to register a
fixed dummy regulator. This is sufficient in principle, since there is no
reason to register multiple such regulators. The user can simply supply all
consumers in one array and use it to initialise such a regulator. However,
in some cases it can be convenient to register multiple such regulators.
This is also a prerequisite for the upcoming patch, that will add a voltage
parameter to this function. The original function is provided as a wrapper
macro.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver supports TI/National LP8720, LP8725 PMIC.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Reviewed-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds two exported functions. One allows to mark option
instance as changed and the second processes change check and does
transfer of changed options to userspace.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce struct team_option_inst_info and push option instance info
there. It can be then easily passed to gsetter context and used for
feature async option changes.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
here is our second pull request for net-next. In this series Federico
Vaga adds a pci driver for c_can/d_can hardware using the existing
generic c_can driver. The remaining 6 patches are by Oliver Hartkopp.
He adds CANFD support to the CAN stack while keeping binary
compatibility for existing applications. CANFD is an extension to the
existing CAN standard, it allows longer CAN frames and/or higher data
rates. There's no real hardware available yet, but this series adds
CANFD support to the vcan driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John Linville says:
====================
This is a sizeable batch of updates intended for 3.6...
The bulk of the changes here are Bluetooth. Gustavo says:
Here goes the first Bluetooth pull request for 3.6, we have
queued quite a lot of work. Andrei Emeltchenko added the AMP
Manager code, a lot of work is needed, but the first bit are
already there. This code is disabled by default. Mat Martineau
changed the whole L2CAP ERTM state machine code, replacing
the old one with a new implementation. Besides that we had
lot of coding style fixes (to follow net rules), more l2cap
core separation from socket and many clean ups and fixed all
over the tree.
Along with the above, there is a healthy dose of ath9k, iwlwifi,
and other driver updates. There is also another pull from the
wireless tree to resolve some merge issues. I also fixed-up some
merge discrepencies between net-next and wireless-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- update sanity checks
- add DLC to length conversion helpers
- can_dlc2len() - get data length from can_dlc with sanitized can_dlc
- can_len2dlc() - map the sanitized data length to an appropriate DLC
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
- introduce a new sockopt CAN_RAW_FD_FRAMES to allow CAN FD frames
- handle CAN frames and CAN FD frames simultaneously when enabled
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
- handle ETH_P_CAN and ETH_P_CANFD skbuffs
- update sanity checks for CAN and CAN FD
- make sure the CAN frame can pass the selected CAN netdevice on send
- bump core version and abi version to indicate the new CAN FD support
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
- add new struct canfd_frame
- check identical element offsets in struct can_frame and struct canfd_frame
- new ETH_P_CANFD definition to tag CAN FD skbs correctly
- add CAN_MTU and CANFD_MTU definitions for easy frame and mode detection
- add CAN[FD]_MAX_[DLC|DLEN] helper constants to remove hard coded values
- update existing struct can_frame with helper constants and comments
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The S5M8767A can't know status of ap reset.
So, After AP watchdog reset, AP can't boot normally.
Problem can be happened like below condition.
- AP Bootable lowest voltage(vdd_arm): 0.9v
- AP DVFS voltage table: 0.8v, 0.9v, 1.0v
- During AP works on lowest voltage(0.8V), watchdog reset is asserted
- AP can't boot, because vdd arm is still 0.8v
Solution
- Basic concept:
After ap watchdog reset, GPIO configuration is changed by default value
- S5M8767A has function of voltage control with gpio (8 levels with 3 gpios)
- Set bootable voltage on level 0 -> can work with default gpio configuration
- In the probing, Change voltage control level from level 0 to level 1
- Execute normal dvfs operation on level 1
- After watchdog reset, ap gpio is set by default value
- PMIC operation mode is changed by ap reset (level1 -> level0)
- Regardless of previous vdd_arm voltage, AP always can be booted.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ERROR: "nfqnl_ct_parse" [net/netfilter/nfnetlink_queue.ko] undefined!
ERROR: "nfqnl_ct_seq_adjust" [net/netfilter/nfnetlink_queue.ko] undefined!
ERROR: "nfqnl_ct_put" [net/netfilter/nfnetlink_queue.ko] undefined!
ERROR: "nfqnl_ct_get" [net/netfilter/nfnetlink_queue.ko] undefined!
We have to use CONFIG_NETFILTER_NETLINK_QUEUE_CT in
include/net/netfilter/nfnetlink_queue.h, not CONFIG_NF_CONNTRACK.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move AUTO_OFF_TIMEOUT to other constants changing name to
HCI_AUTO_OFF_TIMEOUT and convert to jiffies.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In "9cb0176 netfilter: add glue code to integrate nfnetlink_queue and ctnetlink"
the compilation with NF_CONNTRACK disabled is broken. This patch fixes this
issue.
I have moved the conntrack part into nfnetlink_queue_ct.c to avoid
peppering the entire nfnetlink_queue.c code with ifdefs.
I also needed to rename nfnetlink_queue.c to nfnetlink_queue_pkt.c
to update the net/netfilter/Makefile to support conditional compilation
of the conntrack integration.
This patch also adds CONFIG_NETFILTER_QUEUE_CT in case you want to explicitly
disable the integration between nf_conntrack and nfnetlink_queue.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add a helper function for executing the common tasks which are usually involved
in setting up a simple software ringbuffer. It will allocate the buffer,
allocate the pollfunc and register the buffer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tell the application whether the hardware seek is bounded and/or wraps around.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It should be a mistake due to copy & paste in header file
Correct it in videobuf2-dma-config.h for avoiding duplicate include it
Change-Id: I1f71fcec2889c033c7db380c58d9a1369c5afb35
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On some systems, struct usb_device_id doesn't align properly due to the
recent changes in it. So pad out the driver_info field to align on a
boundry that systems can handle it.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The asm-generic/bug.h __ASSEMBLY__ guarding is completely bogus, which
tripped up the powerpc build when the kernel.h include was added:
In file included from include/asm-generic/bug.h:5:0,
from arch/powerpc/include/asm/bug.h:127,
from arch/powerpc/kernel/head_64.S:31:
include/linux/kernel.h:44:0: warning: "ALIGN" redefined [enabled by default]
include/linux/linkage.h:57:0: note: this is the location of the previous definition
include/linux/sysinfo.h: Assembler messages:
include/linux/sysinfo.h:7: Error: Unrecognized opcode: `struct'
include/linux/sysinfo.h:8: Error: Unrecognized opcode: `__kernel_long_t'
Moving the __ASSEMBLY__ guard up and stashing the kernel.h include under
it fixes this up, as well as covering the case the original fix was
attempting to handle.
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 5963e317b1 ("ftrace/x86: Do not change stacks in DEBUG when
calling lockdep") prevented lockdep calls from the int3 breakpoint handler
from reseting the stack if a function that was called was in the process
of being converted for tracing and had a breakpoint on it. The idea is,
before calling the lockdep code, do a load_idt() to the special IDT that
kept the breakpoint stack from reseting. This worked well as a quick fix
for this kernel release, until a certain config caused a lockup in the
function tracer start up tests.
Investigating it, I found that the load_idt that was used to prevent
the int3 from changing stacks was itself being traced!
Even though the config had CONFIG_OPTIMIZE_INLINING disabled, and
all 'inline' tags were set to always inline, there were still cases that
it did not inline! This was caused by CONFIG_PARAVIRT_GUEST, where it
would add a pointer to the native_load_idt() which made that function
to be traced.
Commit 45959ee7aa ("ftrace: Do not function trace inlined functions")
only touched the 'inline' tags when CONFIG_OPMITIZE_INLINING was enabled.
PARAVIRT_GUEST shows that this was not enough and we need to also
mark always_inline with notrace as well.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Tested-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This is a preparatory patch for the KVM/ARM implementation. KVM/ARM will use
the KVM_IRQ_LINE ioctl, which is currently conditional on
__KVM_HAVE_IOAPIC, but ARM obviously doesn't have any IOAPIC support and we
need a separate define.
Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The KVM code sometimes uses CONFIG_HAVE_KVM_IRQCHIP to protect
code that is related to IRQ routing, which not all in-kernel
irqchips may support.
Use KVM_CAP_IRQ_ROUTING instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently there is a 'chicken and egg' issue when the DS is also the mounted
MDS. The nfs_match_client() reference from nfs4_set_ds_client bumps the
cl_count, the nfs_client is not freed at umount, and nfs4_deviceid_purge_client
is not called to dereference the MDS usage of a deviceid which holds a
reference to the DS nfs_client. The result is the umount program returns,
but the nfs_client is not freed, and the cl_session hearbeat continues.
The MDS (and all other nfs mounts) lose their last nfs_client reference in
nfs_free_server when the last nfs_server (fsid) is umounted.
The file layout DS lose their last nfs_client reference in destroy_ds
when the last deviceid referencing the data server is put and destroy_ds is
called. This is triggered by a call to nfs4_deviceid_purge_client which
removes references to a pNFS deviceid used by an MDS mount.
The fix is to track how many pnfs enabled filesystems are mounted from
this server, and then to purge the device id cache once that count reaches
zero.
Reported-by: Jorge Mora <Jorge.Mora@netapp.com>
Reported-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Returning 0 isn't useful, it's not even meaningful if there is a real
regulator there.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As defined in section 13.10.9.3 Case D (802.11-2012), this
control variable is used to limit the mesh STA to send only
one PREQ to a root mesh STA within this interval of time
(in TUs). The default value for this variable is set to
2000 TUs. However, for current implementation, the maximum
configurable of dot11MeshHWMPconfirmationInterval is
restricted by dot11MeshHWMPactivePathTimeout.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HID standard allows sending a feature request to the device which is
answered by an HID report. uhid implements this by sending a UHID_FEATURE
event to user-space which then must answer with UHID_FEATURE_ANSWER. If it
doesn't do this in a timely manner, the request is discarded silently.
We serialize the feature requests, that is, there is always only a single
active feature-request sent to user-space, other requests have to wait.
HIDP and USB-HID do it the same way.
Because we discard feature-requests silently, we must make sure to match
a response to the corresponding request. We use sequence-IDs for this so
user-space must copy the ID from the request into the answer.
Feature-answers are ignored if they do not contain the same ID as the
currently pending feature request.
Internally, we must make sure that feature-requests are synchronized with
UHID_DESTROY and close() events. We must not dead-lock when closing the
HID device, either, so we have to use separate locks.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some drivers that use non-standard HID features require raw output reports
sent to the device. We now forward these requests directly to user-space
so the transport-level driver can correctly send it to the device or
handle it correspondingly.
There is no way to signal back whether the transmission was successful,
moreover, there might be lots of messages coming out from the driver
flushing the output-queue. However, there is currently no driver that
causes this so we are safe. If some drivers need to transmit lots of data
this way, we need a method to synchronize this and can implement another
UHID_OUTPUT_SYNC event.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If the hid-driver wants to send standardized data to the device it uses a
linux input_event. We forward this to the user-space transport-level
driver so they can perform the requested action on the device.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID core notifies us with *_open/*_close callbacks when there is an actual
user of our device. We forward these to user-space so they can react on
this. This allows user-space to skip I/O unless they receive an OPEN
event. When they receive a CLOSE event they can stop I/O again to save
energy.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We send UHID_START and UHID_STOP events to user-space when the HID core
starts/stops the device. This notifies user-space about driver readiness
and data-I/O can start now.
This directly forwards the callbacks from hid-core to user-space.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds a new event type UHID_INPUT which allows user-space to feed raw
HID reports into the HID subsystem. We copy the data into kernel memory
and directly feed it into the HID core.
There is no error handling of the events couldn't be parsed so user-space
should consider all events successfull unless read() returns an error.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
UHID_CREATE and UHID_DESTROY are used to create and destroy a device on an
open uhid char-device. Internally, we allocate and register an HID device
with the HID core and immediately start the device. From now on events may
be received or sent to the device.
The UHID_CREATE event has a payload similar to the data used by
Bluetooth-HIDP when creating a new connection.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When receiving messages from the HID subsystem, we need to process them
and store them in an internal buffer so user-space can read() on the char
device to retrieve the messages.
This adds a static buffer for 32 messages to each uhid device. Each
message is dynamically allocated so the uhid_device structure does not get
too big.
uhid_queue() adds a message to the buffer. If the buffer is full, the
message is discarded. uhid_queue_event() is an helper for messages without
payload.
This also adds a public header: uhid.h. It contains the declarations for
the user-space API. It is built around "struct uhid_event" which contains
a type field which specifies the event type and each event can then add a
variable-length payload. For now, there is only a dummy event but later
patches will add new event types and payloads.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The uncore subsystem in Sandy Bridge-EP consists of 8 components:
Ubox, Cacheing Agent, Home Agent, Memory controller, Power Control,
QPI Link Layer, R2PCIe, R3QPI.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1339741902-8449-9-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Originally from Peter Zijlstra. The helper migrates perf events
from one cpu to another cpu.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1339741902-8449-5-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This change makes it possible to set ramp_delay with 0.xxx mV/uS without
truncation issue.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is essentially the reverse of snd_pcm_rate_to_rate_bit().
This is generally useful as the Compress API uses the rate bit
directly and it helps to be able to map back to the actual sample
rate.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All driver specific and fairly small. The pxa-ssp changes are larger
than I'd like but they're build failures and are pretty clear to
inspection.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=67R8
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for 3.5
All driver specific and fairly small. The pxa-ssp changes are larger
than I'd like but they're build failures and are pretty clear to
inspection.
Battery and charger contribute to Thermals in most of the embedded
devices. So, it makes sense to identify them as Thermal zones in a
particular platform.
This patch registers a thermal zone if the power supply is reporting
a temperature property. The thermal zone will be used by platform's
thermal management solution.
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Devices with register paging or indirectly accessed registers can configure
register mapping to map those on virtual address range. During access to
virtually mapped register range, indirect addressing is processed
automatically, in following steps:
1. selector for page or indirect register is updated (when needed);
2. register in data window is accessed.
Configuration should provide minimum and maximum register for virtual range,
details of selector field for page selection, minimum and maximum register of
data window for indirect access.
Virtual range registers are managed by cache as well as direct access
registers. In order to make indirect access more efficient, selector register
should be declared as non-volatile, if possible.
struct regmap_config is extended with the following:
struct regmap_range_cfg *ranges;
unsigned int n_ranges;
[Also reordered debugfs init to later on since the cleanup code was
conflicting with the new cleanup code for ranges anyway -- broonie]
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For some hardwares ramp_delay for BUCKs is a configurable parameter which can
be configured through DT or board file.This patch adds ramp_delay to regulator
constraints and allow user to configure it for regulators which supports this
feature, through DT or board file. It will provide two ways of setting the
ramp_delay for a regulator:
First, by setting it as constraints in board file(for configurable
regulators) and set_machine_constraints() will take care of setting it on
hardware by calling(the provided) .set_ramp_delay() operation(callback).
Second, by setting it as data in regulator_desc(as fixed/default
ramp_delay rate) for a regulator in driver.
regulator_set_voltage_time_sel() will give preference to
constraints->ramp_delay while reading ramp_delay rate for regulator. Similarly
users should also take care accordingly while refering ramp_delay rate(in case
of implementing their private .set_voltage_time_sel() callbacks for different
regulators).
[Rewrote subject for 80 columns -- broonie]
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pablo says:
====================
This is the second batch of Netfilter updates for net-next. It contains the
kernel changes for the new user-space connection tracking helper
infrastructure.
More details on this infrastructure are provides here:
http://lwn.net/Articles/500196/
Still, I plan to provide some official documentation through the
conntrack-tools user manual on how to setup user-space utilities for this.
So far, it provides two helper in user-space, one for NFSv3 and another for
Oracle/SQLnet/TNS. Yet in my TODO list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix code style - place the asterisk where it belongs.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_intx_mask_supported() assumes INTx masking is supported if the
PCI_COMMAND_INTX_DISABLE bit is writable. But when that bit is set,
some devices don't actually mask INTx or update PCI_STATUS_INTERRUPT
as we expect.
This patch adds a way for quirks to identify these broken devices.
[bhelgaas: split out from Chelsio quirk addition]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There are good reasons to supports helpers in user-space instead:
* Rapid connection tracking helper development, as developing code
in user-space is usually faster.
* Reliability: A buggy helper does not crash the kernel. Moreover,
we can monitor the helper process and restart it in case of problems.
* Security: Avoid complex string matching and mangling in kernel-space
running in privileged mode. Going further, we can even think about
running user-space helpers as a non-root process.
* Extensibility: It allows the development of very specific helpers (most
likely non-standard proprietary protocols) that are very likely not to be
accepted for mainline inclusion in the form of kernel-space connection
tracking helpers.
This patch adds the infrastructure to allow the implementation of
user-space conntrack helpers by means of the new nfnetlink subsystem
`nfnetlink_cthelper' and the existing queueing infrastructure
(nfnetlink_queue).
I had to add the new hook NF_IP6_PRI_CONNTRACK_HELPER to register
ipv[4|6]_helper which results from splitting ipv[4|6]_confirm into
two pieces. This change is required not to break NAT sequence
adjustment and conntrack confirmation for traffic that is enqueued
to our user-space conntrack helpers.
Basic operation, in a few steps:
1) Register user-space helper by means of `nfct':
nfct helper add ftp inet tcp
[ It must be a valid existing helper supported by conntrack-tools ]
2) Add rules to enable the FTP user-space helper which is
used to track traffic going to TCP port 21.
For locally generated packets:
iptables -I OUTPUT -t raw -p tcp --dport 21 -j CT --helper ftp
For non-locally generated packets:
iptables -I PREROUTING -t raw -p tcp --dport 21 -j CT --helper ftp
3) Run the test conntrackd in helper mode (see example files under
doc/helper/conntrackd.conf
conntrackd
4) Generate FTP traffic going, if everything is OK, then conntrackd
should create expectations (you can check that with `conntrack':
conntrack -E expect
[NEW] 301 proto=6 src=192.168.1.136 dst=130.89.148.12 sport=0 dport=54037 mask-src=255.255.255.255 mask-dst=255.255.255.255 sport=0 dport=65535 master-src=192.168.1.136 master-dst=130.89.148.12 sport=57127 dport=21 class=0 helper=ftp
[DESTROY] 301 proto=6 src=192.168.1.136 dst=130.89.148.12 sport=0 dport=54037 mask-src=255.255.255.255 mask-dst=255.255.255.255 sport=0 dport=65535 master-src=192.168.1.136 master-dst=130.89.148.12 sport=57127 dport=21 class=0 helper=ftp
This confirms that our test helper is receiving packets including the
conntrack information, and adding expectations in kernel-space.
The user-space helper can also store its private tracking information
in the conntrack structure in the kernel via the CTA_HELP_INFO. The
kernel will consider this a binary blob whose layout is unknown. This
information will be included in the information that is transfered
to user-space via glue code that integrates nfnetlink_queue and
ctnetlink.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
User-space programs that receive traffic via NFQUEUE may mangle packets.
If NAT is enabled, this usually puzzles sequence tracking, leading to
traffic disruptions.
With this patch, nfnl_queue will make the corresponding NAT TCP sequence
adjustment if:
1) The packet has been mangled,
2) the NFQA_CFG_F_CONNTRACK flag has been set, and
3) NAT is detected.
There are some records on the Internet complaning about this issue:
http://stackoverflow.com/questions/260757/packet-mangling-utilities-besides-iptables
By now, we only support TCP since we have no helpers for DCCP or SCTP.
Better to add this if we ever have some helper over those layer 4 protocols.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch allows you to include the conntrack information together
with the packet that is sent to user-space via NFQUEUE.
Previously, there was no integration between ctnetlink and
nfnetlink_queue. If you wanted to access conntrack information
from your libnetfilter_queue program, you required to query
ctnetlink from user-space to obtain it. Thus, delaying the packet
processing even more.
Including the conntrack information is optional, you can set it
via NFQA_CFG_F_CONNTRACK flag with the new NFQA_CFG_FLAGS attribute.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch uses the new variable length conntrack extensions.
Instead of using union nf_conntrack_help that contain all the
helper private data information, we allocate variable length
area to store the private helper data.
This patch includes the modification of all existing helpers.
It also includes a couple of include header to avoid compilation
warnings.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We can now define conntrack extensions of variable size. This
patch is useful to get rid of these unions:
union nf_conntrack_help
union nf_conntrack_proto
union nf_conntrack_nat_help
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch modifies the struct nf_conntrack_helper to allocate
the room for the helper name. The maximum length is 16 bytes
(this was already introduced in 2.6.24).
For the maximum length for expectation policy names, I have
also selected 16 bytes.
This patch is required by the follow-up patch to support
user-space connection tracking helpers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fix warnings on some architectures/configs (not on x86):
include/linux/vga_switcheroo.h:28:30: warning: 'struct pci_dev' declared inside parameter list [enabled by default]
include/linux/vga_switcheroo.h:28:30: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Takashi Iwai <tiwai@suse.de>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
net/ipv6/route.c
Pull in 'net' again to get the revert of Thomas's change
which introduced regressions.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2a0c451ade.
It causes crashes, because now ip6_null_entry is used before
it is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
Minchan Kim reports that when a system has many swap areas, and tmpfs
swaps out to the ninth or more, shmem_getpage_gfp()'s attempts to read
back the page cannot locate it, and the read fails with -ENOMEM.
Whoops. Yes, I blindly followed read_swap_header()'s pte_to_swp_entry(
swp_entry_to_pte()) technique for determining maximum usable swap
offset, without stopping to realize that that actually depends upon the
pte swap encoding shifting swap offset to the higher bits and truncating
it there. Whereas our radix_tree swap encoding leaves offset in the
lower bits: it's swap "type" (that is, index of swap area) that was
truncated.
Fix it by reducing the SWP_TYPE_SHIFT() in swapops.h, and removing the
broken radix_to_swp_entry(swp_to_radix_entry()) from read_swap_header().
This does not reduce the usable size of a swap area any further, it
leaves it as claimed when making the original commit: no change from 3.0
on x86_64, nor on i386 without PAE; but 3.0's 512GB is reduced to 128GB
per swapfile on i386 with PAE. It's not a change I would have risked
five years ago, but with x86_64 supported for ten years, I believe it's
appropriate now.
Hmm, and what if some architecture implements its swap pte with offset
encoded below type? That would equally break the maximum usable swap
offset check. Happily, they all follow the same tradition of encoding
offset above type, but I'll prepare a check on that for next.
Reported-and-Reviewed-and-Tested-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org [3.1, 3.2, 3.3, 3.4]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Highlights include:
- Fix a couple of mount regressions due to the recent cleanups.
- Fix an Oops in the open recovery code
- Fix an rpc_pipefs upcall hang that results from some of the
net namespace work from 3.4.x (stable kernel candidate).
- Fix a couple of write and o_direct regressions that were found
at last weeks Bakeathon testing event in Ann Arbor.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=unbu
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.5-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- Fix a couple of mount regressions due to the recent cleanups.
- Fix an Oops in the open recovery code
- Fix an rpc_pipefs upcall hang that results from some of the net
namespace work from 3.4.x (stable kernel candidate).
- Fix a couple of write and o_direct regressions that were found at
last weeks Bakeathon testing event in Ann Arbor."
* tag 'nfs-for-3.5-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: add an endian notation for sparse
NFSv4.1: integer overflow in decode_cb_sequence_args()
rpc_pipefs: allow rpc_purge_list to take a NULL waitq pointer
NFSv4 do not send an empty SETATTR compound
NFSv2: EOF incorrectly set on short read
NFS: Use the NFS_DEFAULT_VERSION for v2 and v3 mounts
NFS: fix directio refcount bug on commit
NFSv4: Fix unnecessary delegation returns in nfs4_do_open
NFSv4.1: Convert another trivial printk into a dprintk
NFS4: Fix open bug when pnfs module blacklisted
NFS: Remove incorrect BUG_ON in nfs_found_client
NFS: Map minor mismatch error to protocol not support error.
NFS: Fix a commit bug
NFS4: Set parsed mount data version to 4
NFSv4.1: Ensure we clear session state flags after a session creation
NFSv4.1: Convert a trivial printk into a dprintk
NFSv4: Fix up decode_attr_mdsthreshold
NFSv4: Fix an Oops in the open recovery code
NFSv4.1: Fix a request leak on the back channel
Here are a bunch of tiny fixes for the USB core and drivers for 3.5-rc3
A bunch of gadget fixes, and new device ids, as well as some fixes for a number
of different regressions that have been reported recently. We also fixed some
PCI host controllers to resolve a long-standing bug with a whole class of host
controllers that have been plaguing people for a number of kernel releases,
preventing their systems from suspending properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/byIEACgkQMUfUDdst+ykLBwCgiAi/cS4ObblcBEbnBvosPgsA
PqEAoJLMAwhcozeEOWLhb++45Vs+UjKv
=HAWc
-----END PGP SIGNATURE-----
Merge tag 'usb-3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a bunch of tiny fixes for the USB core and drivers for
3.5-rc3
A bunch of gadget fixes, and new device ids, as well as some fixes for
a number of different regressions that have been reported recently.
We also fixed some PCI host controllers to resolve a long-standing bug
with a whole class of host controllers that have been plaguing people
for a number of kernel releases, preventing their systems from
suspending properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (41 commits)
USB: fix gathering of interface associations
usb: ehci-sh: fix illegal phy_init() running when platform_data is NULL
usb: cdc-acm: fix devices not unthrottled on open
Fix OMAP EHCI suspend/resume failure (i693)
USB: ohci-hub: Mark ohci_finish_controller_resume() as __maybe_unused
usb: use usb_serial_put in usb_serial_probe errors
USB: EHCI: Fix build warning in xilinx ehci driver
USB: fix PS3 EHCI systems
xHCI: Increase the timeout for controller save/restore state operation
xhci: Don't free endpoints in xhci_mem_cleanup()
xhci: Fix invalid loop check in xhci_free_tt_info()
xhci: Fix error path return value.
USB: Checking the wrong variable in usb_disable_lpm()
usb-storage: Add 090c:1000 to unusal-devs
USB: serial-generic: use a single set of device IDs
USB: serial: Enforce USB driver and USB serial driver match
USB: add NO_D3_DURING_SLEEP flag and revert 151b612847
USB: option: add more YUGA device ids
USB: mos7840: Fix compilation of usb serial driver
USB: option: fix memory leak
...
Pull core updates (RCU and locking) from Ingo Molnar:
"Most of the diffstat comes from the RCU slow boot regression fixes,
but there's also a debuggability improvements/fixes."
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
memblock: Document memblock_is_region_{memory,reserved}()
rcu: Precompute RCU_FAST_NO_HZ timer offsets
rcu: Move RCU_FAST_NO_HZ per-CPU variables to rcu_dynticks structure
rcu: Update RCU_FAST_NO_HZ tracing for lazy callbacks
rcu: RCU_FAST_NO_HZ detection of callback adoption
spinlock: Indicate that a lockup is only suspected
kdump: Execute kmsg_dump(KMSG_DUMP_PANIC) after smp_send_stop()
panic: Make panic_on_oops configurable
Pull target updates from Nicholas Bellinger:
"This series contains post merge qla_target.c / tcm_qla2xxx bugfixes
from the past weeks, including the patch to allow target-core to use
an optional session shutdown callback to help address an active I/O
shutdown bug in tcm_qla2xxx code (Joern).
Also included is a target regression bugfix releated to explict ALUA
target port group CDB emulation that is CC'ed to stable (Roland)."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
qla2xxx: Remove version.h header file inclusion
tcm_qla2xxx: Handle malformed wwn strings properly
tcm_qla2xxx: tcm_qla2xxx_handle_tmr() can be static
qla2xxx: Don't leak commands we give up on in qlt_do_work()
qla2xxx: Don't crash if we can't find cmd for failed CTIO
tcm_qla2xxx: Don't insert nacls without sessions into the btree
target: Return error to initiator if SET TARGET PORT GROUPS emulation fails
tcm_qla2xxx: Clear session s_id + loop_id earlier during shutdown
tcm_qla2xxx: Convert to TFO->put_session() usage
target: Add TFO->put_session() caller for HW fabric session shutdown
Conflicts:
net/ipv6/route.c
This deals with a merge conflict between the net-next addition of the
inetpeer network namespace ops, and Thomas Graf's bug fix in
2a0c451ade which makes sure we don't
register /proc/net/ipv6_route before it is actually safe to do so.
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc/net/ipv6_route reflects the contents of fib_table_hash. The proc
handler is installed in ip6_route_net_init() whereas fib_table_hash is
allocated in fib6_net_init() _after_ the proc handler has been installed.
This opens up a short time frame to access fib_table_hash with its pants
down.
fib6_init() as a whole can't be moved to an earlier position as it also
registers the rtnetlink message handlers which should be registered at
the end. Therefore split it into fib6_init() which is run early and
fib6_init_late() to register the rtnetlink message handlers.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Orphaning skb in dev_hard_start_xmit() makes bonding behavior
unfriendly for applications sending big UDP bursts : Once packets
pass the bonding device and come to real device, they might hit a full
qdisc and be dropped. Without orphaning, the sender is automatically
throttled because sk->sk_wmemalloc reaches sk->sk_sndbuf (assuming
sk_sndbuf is not too big)
We could try to defer the orphaning adding another test in
dev_hard_start_xmit(), but all this seems of little gain,
now that BQL tends to make packets more likely to be parked
in Qdisc queues instead of NIC TX ring, in cases where performance
matters.
Reverts commits :
fc6055a5ba net: Introduce skb_orphan_try()
87fd308cfc net: skb_tx_hash() fix relative to skb_orphan_try()
and removes SKBTX_DRV_NEEDS_SK_REF flag
Reported-and-bisected-by: Jean-Michel Hautbois <jhautbois@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
One tricky issue on the ipv6 side vs. ipv4 is that the ICMP callouts
to handle the error pass the 32-bit info cookie in network byte order
whereas ipv4 passes it around in host byte order.
Like the ipv4 side, we have two helper functions. One for when we
have a socket context and one for when we do not.
ip6ip6 tunnels are not handled here, because they handle PMTU events
by essentially relaying another ICMP packet-too-big message back to
the original sender.
This patch allows us to get rid of rt6_do_pmtu_disc(). It handles all
kinds of situations that simply cannot happen when we do the PMTU
update directly using a fully resolved route.
In fact, the "plen == 128" check in ip6_rt_update_pmtu() can very
likely be removed or changed into a BUG_ON() check. We should never
have a prefixed ipv6 route when we get there.
Another piece of strange history here is that TCP and DCCP, unlike in
ipv4, never invoke the update_pmtu() method from their ICMP error
handlers. This is incredibly astonishing since this is the context
where we have the most accurate context in which to make a PMTU
update, namely we have a fully connected socket and associated cached
socket route.
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide an iterator to receive the log buffer content, and convert all
kmsg_dump() users to it.
The structured data in the kmsg buffer now contains binary data, which
should no longer be copied verbatim to the kmsg_dump() users.
The iterator should provide reliable access to the buffer data, and also
supports proper log line-aware chunking of data while iterating.
Signed-off-by: Kay Sievers <kay@vrfy.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Reported-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Tested-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While common irqdesc allocation is node aware, the irqdomain code is not.
Presently we observe a number of regressions/inconsistencies on
NUMA-capable platforms:
- Platforms using irqdomains with legacy mappings, where the
irq_descs are allocated node-local and the irqdomain data
structure is not.
- Drivers implementing irqdomains will lose node locality
regardless of the underlying struct device's node id.
This plugs in NUMA node id proliferation across the various allocation
callsites by way of_node_to_nid() node lookup. While of_node_to_nid()
does the right thing for OF-capable platforms it doesn't presently handle
the non-DT case. This is trivially dealt with by simply wraping in to
numa_node_id() unconditionally.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The pattern (np ? np->full_name : "<none>") is rather common in the
kernel, but can also make for quite long lines. This patch adds a new
inline function, of_node_full_name() so that the test for a valid node
pointer doesn't need to be open coded at all call sites.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Move the ->irq_set_affinity() routines out of the #ifdef CONFIG_SMP
sections and use config_enabled(CONFIG_SMP) checks inside those
routines. Thus making those routines simple null stubs for
!CONFIG_SMP and retaining those routines with no additional
runtime overhead for CONFIG_SMP kernels.
Cleans up the ifdef CONFIG_SMP in and around routines related to
irq_set_affinity in io_apic and irq_remapping subsystems.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: torvalds@linux-foundation.org
Cc: joerg.roedel@amd.com
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Link: http://lkml.kernel.org/r/1339723729.3475.63.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds helpers to support device tree bindings for the generic
PWM API. Device tree binding documentation for PWM controllers is also
provided.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This commit adds an empty of_parse_phandle_with_args() function for
!CONFIG_OF builds.
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This commit adds an empty of_property_match_string() function for
!CONFIG_OF builds.
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
In order to get rid of the global namespace for PWM devices, this commit
provides an alternative method, similar to that of the regulator or
clock frameworks, for registering a static mapping for PWM devices. This
works by providing a table with a provider/consumer map in the board
setup code.
With the new pwm_get() and pwm_put() functions available, usage of
pwm_request() and pwm_free() becomes deprecated.
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This commit adds a debugfs interface that can be used to list the
current internal state of the PWM devices registered with the PWM
framework.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Many PWM controllers provide access to more than a single PWM output and
may even share some resource among them. Allowing a PWM chip to provide
multiple PWM devices enables better sharing of those resources. As a
side-effect this change allows easy integration with the device tree
where a given PWM can be looked up based on the PWM chip's phandle and a
corresponding index.
This commit modifies the PWM core to support multiple PWMs per struct
pwm_chip. It achieves this in a similar way to how gpiolib works, by
allowing PWM ranges to be requested dynamically (pwm_chip.base == -1) or
starting at a given offset (pwm_chip.base >= 0). A chip specifies how
many PWMs it controls using the npwm member. Each of the functions in
the pwm_ops structure gets an additional argument that specified the PWM
number (it can be converted to a per-chip index by subtracting the
chip's base).
The total maximum number of PWM devices is currently fixed to 1024 while
the data is actually stored in a radix tree, thus saving resources if
not all of them are used.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
[eric@eukrea.com: fix error handling in pwmchip_add]
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch adds framework support for PWM (pulse width modulation) devices.
The is a barebone PWM API already in the kernel under include/linux/pwm.h,
but it does not allow for multiple drivers as each of them implements the
pwm_*() functions.
There are other PWM framework patches around from Bill Gatliff. Unlike
his framework this one does not change the existing API for PWMs so that
this framework can act as a drop in replacement for the existing API.
Why another framework?
Several people argue that there should not be another framework for PWMs
but they should be integrated into one of the existing frameworks like led
or hwmon. Unlike these frameworks the PWM framework is agnostic to the
purpose of the PWM. In fact, a PWM can drive a LED, but this makes the
LED framework a user of a PWM, like already done in leds-pwm.c. The gpio
framework also is not suitable for PWMs. Every gpio could be turned into
a PWM using timer based toggling, but on the other hand not every PWM hardware
device can be turned into a gpio due to the lack of hardware capabilities.
This patch does not try to improve the PWM API yet, this could be done in
subsequent patches.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
[thierry.reding@avionic-design.de: fixup typos, kerneldoc comments]
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This function was only used by btrfs code in btrfs_abort_devices()
(seems in a wrong way).
It was removed in commit d07eb91170,
So, Let's remove the dead code to avoid any confusion.
Changes in v2: update commit log, btrfs_abort_devices() was removed
already.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-kernel@vger.kernel.org
Cc: Chris Mason <chris.mason@oracle.com>
Cc: linux-btrfs@vger.kernel.org
Cc: David Sterba <dave@jikos.cz>
Signed-off-by: Asias He <asias@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With ip_rt_frag_needed() removed, we have to explicitly update PMTU
information in every ICMP error handler.
Create two helper functions to facilitate this.
1) ipv4_sk_update_pmtu()
This updates the PMTU when we have a socket context to
work with.
2) ipv4_update_pmtu()
Raw version, used when no socket context is available. For this
interface, we essentially just pass in explicit arguments for
the flow identity information we would have extracted from the
socket.
And you'll notice that ipv4_sk_update_pmtu() is simply implemented
in terms of ipv4_update_pmtu()
Note that __ip_route_output_key() is used, rather than something like
ip_route_output_flow() or ip_route_output_key(). This is because we
absolutely do not want to end up with a route that does IPSEC
encapsulation and the like. Instead, we only want the route that
would get us to the node described by the outermost IP header.
Reported-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TRACE_EVENT_FL_ENABLED_BIT,
TRACE_EVENT_FL_FILTERED_BIT,
TRACE_EVENT_FL_RECORDED_CMD_BIT,
Have comments about what they are, but:
TRACE_EVENT_FL_CAP_ANY_BIT,
TRACE_EVENT_FL_NO_SET_FILTER_BIT,
TRACE_EVENT_FL_IGNORE_ENABLE_BIT,
do not, making them second class citizens. To prevent another
class warfare, these bits have protested for their right to be
commented. And By Golly! I'll give them what they want!
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Use the rsvd1 field in execbuf2 to specify the context ID associated
with the workload. This will allow the driver to do the proper context
switch when/if needed.
v2: Add checks for context switches on rings not supporting contexts.
Before the code would silently ignore such requests.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Add the interfaces to allow user space to create and destroy contexts.
Contexts are destroyed automatically if the file descriptor for the dri
device is closed.
Following convention as usual here causes checkpatch warnings.
v2: with is_initialized, no longer need to init at create
drop the context switch on create (daniel)
v3: Use interruptible lock (Chris)
return -ENODEV in !GEM case (Chris)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
- Fix a regression of USB-audio PCM assignment since 3.4
- A few VGA-switcheroo-related fixes for proper HDMI audio enablement
- Fixed the missing initializations of HD-audio verbs, which may have
resulted in various breakage
- Some driver-specific ASoC updates
- A few fixes for the dynamic PCM code
- The addition of pinctrl support for the i.MX audmux which didn't make it
into -rc1 due to cross tree dependency issues
- A few minor fixes in compress API codes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=Hrh7
-----END PGP SIGNATURE-----
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- Fix a regression of USB-audio PCM assignment since 3.4
- A few VGA-switcheroo-related fixes for proper HDMI audio enablement
- Fixed the missing initializations of HD-audio verbs, which may have
resulted in various breakage
- Some driver-specific ASoC updates
- A few fixes for the dynamic PCM code
- The addition of pinctrl support for the i.MX audmux which didn't make
it into -rc1 due to cross tree dependency issues
- A few minor fixes in compress API codes
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Don't forget to call init verbs added by fixup list
ALSA: HDA: Pin fixup for Zotac Z68 motherboard
ALSA: compress_core: cleanup pointers on stop
ALSA: compress_core: don't wake up on pause
ALSA: hda - Fix detection of Creative SoundCore3D controllers
vga_switcheroo: Enable/disable audio clients at the right time
ALSA: hda - HDMI Audio init all connectors when VGA-switcheroo is off
vga_switcheroo: Fix error without CONFIG_VGA_SWITCHEROO
ALSA: hda - Fix uninitialized HDMI controllers with VGA-switcheroo
vga_switcheroo: Add a helper function to get the client state
ALSA: usb-audio: Fix substream assignments
ASoC: tegra: add MODULE_DEVICE_TABLE to tegra30_ahub
ASoC: wm2000: Always use a 4s timeout for the firmware
ASoC: dapm: Fix input list to use source widgets
ASoC: dpcm: Fix dpcm_get_be() to check that DAI is BE
ASoC: wm8994: Apply volume updates with clocks enabled
ASoC: wm8994: Ensure all AIFnCLK events are run from the _late variants
ASoC: imx-audmux: add pinctrl support
ASoC: dapm: Fix connected widget capture path query.
Pull networking fixes from David S. Miller:
This has the fix for the wireless issues I ran into the other week as
well as:
1) Fix CAN c_can driver transmit handling resulting in BUG check
triggers, from AnilKumar Ch.
2) Fix packet drop monitor sleeping in atomic context, from Eric
Dumazet.
3) Fix mv643xx_eth driver build regression, from Andrew Lunn.
4) Inetpeer freeing needs an RCU grace period in order to avoid races
during tree invalidation. From Eric Dumazet.
5) Fix endianness bugs in xt_HMARK netfilter module, from Hans
Schillstrom.
6) Add proper module refcounting to l2tp_eth to avoid crash on module
unload, from Eric Dumazet.
7) Fix truncation of neighbour entry dumps due to logic errors in
neigh_dump_info() and friends, from Eric Dumazet.
8) The conversion of fib6_age() to dst_neigh_lookup() accidently
reversed the logic of a flags test, fix from Thomas Graf.
9) Fix checksum configuration in newer sky2 chips, from Stephen
Hemminger.
10) Revert BQL support in NIU driver, doesn't work.
11) l2tp_ip_sendmsg() illegally uses a route without a proper reference.
From Eric Dumazet.
12) be2net driver references an SKB after it's potentially been freed,
also from Eric Dumazet.
13) Fix RCU stalls in dummy net driver init. Also from Eric Dumazet.
14) lpc_eth has several bugs in it's transmit engine leading to packet
leaks and improper queue wakes, from Eric Dumazet.
15) Apply short DMA workaround to more tg3 chips, from Matt Carlson.
16) Add tilegx network driver.
17) Bonding queue mapping for a packet can get corrupted, fix from Eric
Dumazet.
18) Fix bug in netpoll_send_udp() SKB management that can leave garbage
in the payload in certain situations. From Eric Dumazet.
19) bnx2x driver interprets chip RX checksum offload incorrectly in
encapsulation situations. Fix from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
bnx2x: fix checksum validation
netpoll: fix netpoll_send_udp() bugs
bonding: Fix corrupted queue_mapping
bonding:record primary when modify it via sysfs
tilegx network driver: initial support
tg3: Apply short DMA frag workaround to 5906
net: stmmac: Fix clock en-/disable calls
lpc_eth: fix tx completion
lpc_eth: add missing ndo_change_mtu()
dummy: fix rcu_sched self-detected stalls
net: Reorder initialization in ip_route_output to fix gcc warning
virtio-net: fix a race on 32bit arches
r8169: avoid NAPI scheduling delay.
net: Make linux/tcp.h C++ friendly (trivial)
netdev: fix drivers/net/phy/ kernel-doc warnings
net/core: fix kernel-doc warnings
be2net: fix a race in be_xmit()
l2tp: fix a race in l2tp_ip_sendmsg()
mac80211: add back channel change flag
NFC: Fix possible NULL ptr deref when getting the name of a socket
...
Generate the proactive PREQ element as defined in
Sec. 13.10.9.3 (Case C) of IEEE Std. 802.11-2012
based on the selection of dot11MeshHWMPRootMode as follow:
dot11MeshHWMPRootMode (2) is proactivePREQnoPREP
dot11MeshHWMPRootMode (3) is proactivePREQwithPREP
The proactive PREQ is generated based on the interval
defined by dot11MeshHWMProotInterval.
With this change, proactive RANN element is now generated
if the dot11MeshHWMPRootMode is set to (4) instead of (1).
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the mesh configuration parameters dot11MeshHWMProotInterval
and dot11MeshHWMPactivePathToRootTimeout to be used by
proactive PREQ mechanism.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define a struct that describes common fields used in all slab allocators.
A slab allocator either uses the common definition (like SLOB) or is
required to provide members of kmem_cache with the definition given.
After that it will be possible to share code that
only operates on those fields of kmem_cache.
The patch basically takes the slob definition of kmem cache and
uses the field namees for the other allocators.
It also standardizes the names used for basic object lengths in
allocators:
object_size Struct size specified at kmem_cache_create. Basically
the payload expected to be used by the subsystem.
size The size of memory allocator for each object. This size
is larger than object_size and includes padding, alignment
and extra metadata for each object (f.e. for debugging
and rcu).
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Add fields to the page struct so that it is properly documented that
slab overlays the lru fields.
This cleans up some casts in slab.
Reviewed-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Define the fields used by slob in mm_types.h and use struct page instead
of struct slob_page in slob. This cleans up numerous of typecasts in slob.c and
makes readers aware of slob's use of page struct fields.
[Also cleans up some bitrot in slob.c. The page struct field layout
in slob.c is an old layout and does not match the one in mm_types.h]
Reviewed-by: Glauber Costa <glommer@parallels.com>
Acked-by: David Rientjes <rientjes@google.com>
Reviewed-by: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
The code tried to maintain the global list of persistent ram zones,
which isn't a great idea overall, plus since Android's ram_console
is no longer there, we can remove some unused functions.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The console log size is configurable via ramoops.console_size
module option, and the log itself is available via
<pstore-mount>/console-ramoops file.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pstore doesn't support logging kernel messages in run-time, it only
dumps dmesg when kernel oopses/panics. This makes pstore useless for
debugging hangs caused by HW issues or improper use of HW (e.g.
weird device inserted -> driver tried to write a reserved bits ->
SoC hanged. In that case we don't get any messages in the pstore.
Therefore, let's add a runtime logging support: PSTORE_TYPE_CONSOLE.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need this for the pstore fixes that went into the staging-linus branch, so
that things apply properly for the pstore/android code merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The list of exit reasons for the kvm_userspace_exit event was
missing recent additions; bring it into sync again.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
A handy function that we will use outside of ram_core soon. But
so far just factor it out and start using it in post_init().
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without the update, we'll only see the new dmesg buffer after the
reboot, but previously we could see it right away. Making an oops
visible in pstore filesystem before reboot is a somewhat dubious
feature, but removing it wasn't an intentional change, so let's
restore it.
For this we have to make persistent_ram_save_old() safe for calling
multiple times, and also extern it.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some composite USB devices provide multiple interfaces
with different functions, all using "vendor-specific"
for class/subclass/protocol. Another OS use interface
numbers to match the driver and interface. It seems
these devices are designed with that in mind - using
static interface numbers for the different functions.
This adds support for matching against the
bInterfaceNumber, allowing such devices to be supported
without having to resort to testing against interface
number whitelists and/or blacklists in the probe.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to pick up the changes to the option driver, which are needed
for follow-on patches from Johan.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to put into the resources list for legacy system.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Will use them insert/update busn res in pci_bus struct.
[bhelgaas: print conflicting entry if insertion fails]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pci_bus secondary/subordinate members are now unused, so remove them.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This adds a busn_res resource in struct pci_bus. This will replace the
secondary/subordinate members and will be used to build a bus number
resource tree to help with bus number allocation.
[bhelgaas: changelog]
CC: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch (as1558) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
A similar patch has already been applied as commit
151b612847 (USB: EHCI: fix crash during
suspend on ASUS computers). The patch supersedes that one and reverts
it. There are two differences:
The old patch added the flag at the USB level; this patch
adds it at the PCI level.
The old patch applied to all chipsets with the same vendor,
subsystem vendor, and product IDs; this patch makes an
exception for a known-good system (based on DMI information).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dâniel Fraga <fragabr@gmail.com>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- to decrease redundant since both ehci_hcd and ohci_hcd have the same variable
- it helps access phy in usb core code
- phy is more meaningful than transceiver
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
renesas_usbhs DMAEngine uses D0FIFO/D1FIFO,
but the data transfer direction should be fixed for keeping consistency.
This patch explain about it on renesas_usbhs.h
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Jones reported a kernel BUG at mm/slub.c:3474! triggered
by splice_shrink_spd() called from vmsplice_to_pipe()
commit 35f3d14dbb (pipe: add support for shrinking and growing pipes)
added capability to adjust pipe->buffers.
Problem is some paths don't hold pipe mutex and assume pipe->buffers
doesn't change for their duration.
Fix this by adding nr_pages_max field in struct splice_pipe_desc, and
use it in place of pipe->buffers where appropriate.
splice_shrink_spd() loses its struct pipe_inode_info argument.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Tom Herbert <therbert@google.com>
Cc: stable <stable@vger.kernel.org> # 2.6.35
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch converts .is_enabled and .get_voltage_sel to
regulator_is_enabled_regmap and regulator_get_voltage_sel_regmap.
For .enable, .disable, and .set_voltage_sel, the write protect level is either
1 or 2. So we cannot use regulator_[enable|disable|set_voltage_sel]_regmap.
Now we store the enable reg/mask and vsel reg/mask in regulator_desc,
so we can remove enable_mask, set_vout_reg, and set_vout_mask from
struct tps_info.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's perfectly sensible to ask if there's a regmap for a device which
doesn't have one so the stubbed version shouldn't complain, the caller
should be prepared for this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
mmp-pcm handle audio dma based on soc-dmaengine
Support mmp and pxa910
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Leo Yan <leoy@marvell.com>
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It should be NL80211_SCHED_SCAN_MATCH_ATTR_SSID as
documented, not NL80211_ATTR_SCHED_SCAN_MATCH_SSID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
MAINTAINERS
drivers/net/wireless/iwlwifi/pcie/trans.c
The iwlwifi conflict was resolved by keeping the code added
in 'net' that turns off the buggy chip feature.
The MAINTAINERS conflict was merely overlapping changes, one
change updated all the wireless web site URLs and the other
changed some GIT trees to be Johannes's instead of John's.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an optional target_core_fabric_ops->put_session() caller
within the existing target_put_session() code path.
This is required by tcm_qla2xxx code in order to invoke it's own fabric
specific session shutdown handler using se_session->sess_kref.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Change flags field to matches userspace structure.
This field needs to be converted to little endian before forward it.
Signed-off-by: Jefferson Delfes <jefferson.delfes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Add dev_loopback_xmit() in order to deduplicate functions
ip_dev_loopback_xmit() (in net/ipv4/ip_output.c) and
ip6_dev_loopback_xmit() (in net/ipv6/ip6_output.c).
I was about to reinvent the wheel when I noticed that
ip_dev_loopback_xmit() and ip6_dev_loopback_xmit() do exactly what I
need and are not IP-only functions, but they were not available to reuse
elsewhere.
ip6_dev_loopback_xmit() does not have line "skb_dst_force(skb);", but I
understand that this is harmless, and should be in dev_loopback_xmit().
Signed-off-by: Michel Machado <michel@digirati.com.br>
CC: "David S. Miller" <davem@davemloft.net>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
CC: James Morris <jmorris@namei.org>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jiri Pirko <jpirko@redhat.com>
CC: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag of EVENT_DEV_WAKING is not used any more, so just remove it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the transmit path of the bonding driver, skb->cb is used to
stash the skb->queue_mapping so that the bonding device can set its
own queue mapping. This value becomes corrupted since the skb->cb is
also used in __dev_xmit_skb.
When transmitting through bonding driver, bond_select_queue is
called from dev_queue_xmit. In bond_select_queue the original
skb->queue_mapping is copied into skb->cb (via bond_queue_mapping)
and skb->queue_mapping is overwritten with the bond driver queue.
Subsequently in dev_queue_xmit, __dev_xmit_skb is called which writes
the packet length into skb->cb, thereby overwriting the stashed
queue mappping. In bond_dev_queue_xmit (called from hard_start_xmit),
the queue mapping for the skb is set to the stashed value which is now
the skb length and hence is an invalid queue for the slave device.
If we want to save skb->queue_mapping into skb->cb[], best place is to
add a field in struct qdisc_skb_cb, to make sure it wont conflict with
other layers (eg : Qdiscc, Infiniband...)
This patchs also makes sure (struct qdisc_skb_cb)->data is aligned on 8
bytes :
netem qdisc for example assumes it can store an u64 in it, without
misalignment penalty.
Note : we only have 20 bytes left in (struct qdisc_skb_cb)->data[].
The largest user is CHOKe and it fills it.
Based on a previous patch from Tom Herbert.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Tom Herbert <therbert@google.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Routing of 127/8 is tradtionally forbidden, we consider
packets from that address block martian when routing and do
not process corresponding ARP requests.
This is a sane default but renders a huge address space
practically unuseable.
The RFC states that no address within the 127/8 block should
ever appear on any network anywhere but it does not forbid
the use of such addresses outside of the loopback device in
particular. For example to address a pool of virtual guests
behind a load balancer.
This patch adds a new interface option 'route_localnet'
enabling routing of the 127/8 address block and processing
of ARP requests on a specific interface.
Note that for the feature to work, the default local route
covering 127/8 dev lo needs to be removed.
Example:
$ sysctl -w net.ipv4.conf.eth0.route_localnet=1
$ ip route del 127.0.0.0/8 dev lo table local
$ ip addr add 127.1.0.1/16 dev eth0
$ ip route flush cache
V2: Fix invalid check to auto flush cache (thanks davem)
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v5:
* fix warnings (Jonathan Cameron)
v4:
* remove unused indio_dev pointer in mcp4725_data (Jonathan Cameron)
* use u16 instead of unsigned short in mcp4725_data (Jonathan Cameron)
* #include mcp4725.h from linux/iio/dac/
v3:
* move from staging to drivers/iio
* switch to chan_spec
* dev_get_drvdata() -> dev_to_iio_dev()
* annotate probe() and remove() with __devinit and __devexit
v2 (based on comments from Jonathan Cameron and Lars-Peter Clausen):
* did NOT switch to chan_spec yet
* rebase to staging-next tree, update iio header locations
* dropped dac.h #include, not needed
* strict_strtol() -> kstrtol()
* call iio_device_unregister() in remove()
* everything in one patch
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When drm/i915 is in control of the gtt, we need to call
the enable function at all the relevant places ourselves.
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To be able to directly set up the intel-gtt code from drm/i915 and
avoid setting up the fake-agp driver we need to prepare a few things:
- pass both the bridge and gpu pci_dev to the probe function and add
code to handle the gpu pdev both being present (for drm/i915) and
not present (fake agp).
- add refcounting to the remove function so that unloading drm/i915
doesn't kill the fake agp driver
v2: Fix up the cleanup and refcount, noticed by Jani Nikula.
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For that to work we need to export the base address of the gtt
mmio window from intel-gtt. Also replace all other uses of
dev->agp by values we already have at hand.
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fill in many missing definitions and add sizeof fields for many
sections allowing for more extensive config parsing.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
For returning errors out to non-PCI code. Re-name xen's version.
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
VFIO PCI support will make use of these for user-initiated
PCI config accesses.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In a PCI environment, transactions aren't always required to reach
the root bus before being re-routed. Intermediate switches between
an endpoint and the root bus can redirect DMA back downstream before
things like IOMMUs have a chance to intervene. Legacy PCI is always
susceptible to this as it operates on a shared bus. PCIe added a
new capability to describe and control this behavior, Access Control
Services, or ACS.
The utility function pci_acs_enabled() allows us to test the ACS
capabilities of an individual devices against a set of flags while
pci_acs_path_enabled() tests a complete path from a given downstream
device up to the specified upstream device. We also include the
ability to add device specific tests as it's likely we'll see
devices that do not implement ACS, but want to indicate support
for various capabilities in this space.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Before Kernel 3.5, no one was checking for the return value of
drm_connector_attach_property, so we never noticed that we were unable
to create some properties. Commit "drm: WARN() when
drm_connector_attach_property fails" added a WARN when we fail to
create a property, and the transition from "connector properties" to
"object properties" changed the warning message a little bit.
On i915 machines with many TV connectors we hit the maximum number of
properties (since each TV connector uses a lot of properties), so we
get a few backtraces in our logs. This commit increases the maximum
number of properties to 24 hoping we'll have enough room for
everybody.
Chris suggested that we convert this code to "lists", but I believe
this conversion can come after we make sure people's dmesgs are not
spammed by our driver.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix kernel-doc warning in input.h:
Warning(include/linux/input.h:140): No description found for parameter 'len'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The platform-data used by the Ux500 ASoC-driver is moved from the
machine-driver context into the codec-driver context. This means
adding the platform-data for 'ab8500-codec' into the main AB8500
platform-data.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The HCI constants are always used in form of jiffies. So just
include the conversion from msecs in the define itself. This has the
advantage of making the code where the timeout is used more readable
and avoiding unnecessary conversions.
The patch is similar to commit ba13ccd9 doing the same job for L2CAP
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch resolves potential issues when accessing PCI Express
Capability structures. The makeup of the capability varies
substantially between v1 and v2:
Version 1 of the PCI Express Capability (defined by PCI Express
1.0 and 1.1 base) neither requires the endpoint to implement the
entire PCIe capability structure nor specifies default values of
registers that are not implemented by the device.
Version 2 of the PCI Express Capability (defined by PCIe 1.1
Capability Structure Expansion ECN, PCIe 2.0, 2.1, and 3.0) added
additional registers to the structure and requires all registers
to be either implemented or hardwired to 0.
Due to the differences in the capability structures, code dealing with
capability features must be careful not to access the additional
registers introduced with v2 unless the device is specifically known to
be a v2 capable device. Otherwise, attempts to access non-existant
registers will occur. This is a subtle issue that is hard to track down
when it occurs (and it has - see commit 864d296cf9).
To try and help mitigate such occurrences, this patch introduces
pci_pcie_cap2() which is similar to pci_pcie_cap() but also checks
that the PCIe capability version is >= 2. pci_pcie_cap2() should be
used for qualifying PCIe capability features introduced after v1.
Suggested by Don Dutile.
Acked-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI Express Latency Tolerance Reporting (LTR) feature's
pci_ltr_supported() routine is currently only used within
drivers/pci/pci.c so make it static.
Acked-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
DMA transactions are tagged with the source ID of the device making
the request. Occasionally hardware screws this up and uses the
source ID of a different device (often the wrong function number of
a multifunction device). A specific Ricoh multifunction device is
a prime example of this problem and included in this patch.
Given a pci_dev, this function returns the pci_dev to use as the
source ID for DMA. When hardware works correctly, this returns
the input device. For the components of the Ricoh multifunction
device, it returns the pci_dev for function 0.
This will be used by IOMMU drivers for determining the boundaries
of IOMMU groups as multiple devices using the same source ID must
be contained within the same group. This can also be used by
existing streaming DMA paths for the same purpose.
[bhelgaas: fold in pci_dev_get() for !CONFIG_PCI]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit f80a3f6238 ("Staging: strip: delete
the driver") left if_strip.h unused: nothing in the tree includes it
anymore. It is still exported, but since nothing in the kernel uses
struct MetricomAddress, that seems pointless. Delete this header too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If no peer actually gets attached (either because create is zero or
the peer allocation fails) we'll trigger a BUG because we
unconditionally do an rt{,6}_peer_ptr() afterwards.
Fix this by guarding it with the proper check.
Signed-off-by: David S. Miller <davem@davemloft.net>
__dev_get_by_name() is slow because pm_qos_req has been inserted between
name[] and name_hlist, adding cache misses.
pm_qos_req has nothing to do at the beginning of struct net_device
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch the owner field of the /dev/radio# device fops was set to
the snd-tea575x-tuner module itself. Meaning that the module which was using
it could be rmmod-ed while the device is open, and then BAD things happen.
I know, as I found out the hard way :)
Note that there is no need to also somehow increase the refcount of the
snd-tea575x-tuner module itself, since any drivers using it will have
symbolic references to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
CC: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Yuck. The VIDIOC_(TRY_)DECODER_CMD ioctls already had ioctl numbers 96 and 97,
and after merging the timings API I forgot to continue numbering from 98. So
now we have two ioctls with number 96 and two with 97.
With the new table-driver ioctl handling in v4l2-ioctl.c it is essential that
each ioctl has its own unique number, so let's fix this quickly for 3.5.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that idle and nohz logics are going to be independant each others,
ts->idle_tick becomes too much a biased name to describe the field that
saves the last scheduled tick on top of which we re-calculate the next
tick to schedule when the timer is restarted.
We want to reuse this even to stop the tick outside idle cases. So let's
rename it to some more generic name: ts->last_tick.
This changes a bit the timer list stat export so we need to increase its
version.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Kernel kobjects have rigid rules: each container object should be
dynamically allocated, and can't be allocated into a single kmalloc.
EDAC never obeyed this rule: it has a single malloc function that
allocates all needed data into a single kzalloc.
As this is not accepted anymore, change the allocation schema of the
EDAC *_info structs to enforce this Kernel standard.
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Greg K H <gregkh@linuxfoundation.org>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Mark Gross <mark.gross@intel.com>
Cc: Tim Small <tim@buttersideup.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Egor Martovetsky <egor@pasemi.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sometimes, it is useful to have a mechanism that generates fake
errors, in order to test the EDAC core code, and the userspace
tools.
Provide such mechanism by adding a few debugfs nodes.
Reviewed-by: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that al users for the old kobj raw access are gone,
we can get rid of the legacy kobj-based structures and
data.
Reviewed-by: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The EDAC subsystem uses the old struct sysdev approach,
creating all nodes using the raw sysfs API. This is bad,
as the API is deprecated.
As we'll be changing the EDAC API, let's first port the existing
code to struct device.
There's one drawback on this patch: driver-specific sysfs
nodes, used by mpc85xx_edac, amd64_edac and i7core_edac
won't be created anymore. While it would be possible to
also port the device-specific code, that would mix kobj with
struct device, with is not recommended. Also, it is easier and nicer
to move the code to the drivers, instead, as the core can get rid
of some complex logic that just emulates what the device_add()
and device_create_file() already does.
The next patches will convert the driver-specific code to use
the device-specific calls. Then, the remaining bits of the old
sysfs API will be removed.
NOTE: a per-MC bus is required, otherwise devices with more than
one memory controller will hit a bug like the one below:
[ 819.094946] EDAC DEBUG: find_mci_by_dev: find_mci_by_dev()
[ 819.094948] EDAC DEBUG: edac_create_sysfs_mci_device: edac_create_sysfs_mci_device() idx=1
[ 819.094952] EDAC DEBUG: edac_create_sysfs_mci_device: edac_create_sysfs_mci_device(): creating device mc1
[ 819.094967] EDAC DEBUG: edac_create_sysfs_mci_device: edac_create_sysfs_mci_device creating dimm0, located at channel 0 slot 0
[ 819.094984] ------------[ cut here ]------------
[ 819.100142] WARNING: at fs/sysfs/dir.c:481 sysfs_add_one+0xc1/0xf0()
[ 819.107282] Hardware name: S2600CP
[ 819.111078] sysfs: cannot create duplicate filename '/bus/edac/devices/dimm0'
[ 819.119062] Modules linked in: sb_edac(+) edac_core ip6table_filter ip6_tables ebtable_nat ebtables ipt_MASQUERADE iptable_nat nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_state nf_conntrack ipt_REJECT xt_CHECKSUM iptable_mangle iptable_filter ip_tables bridge stp llc sunrpc binfmt_misc dm_mirror dm_region_hash dm_log vhost_net macvtap macvlan tun kvm microcode pcspkr iTCO_wdt iTCO_vendor_support igb i2c_i801 i2c_core sg ioatdma dca sr_mod cdrom sd_mod crc_t10dif ahci libahci isci libsas libata scsi_transport_sas scsi_mod wmi dm_mod [last unloaded: scsi_wait_scan]
[ 819.175748] Pid: 10902, comm: modprobe Not tainted 3.3.0-0.11.el7.v12.2.x86_64 #1
[ 819.184113] Call Trace:
[ 819.186868] [<ffffffff8105adaf>] warn_slowpath_common+0x7f/0xc0
[ 819.193573] [<ffffffff8105aea6>] warn_slowpath_fmt+0x46/0x50
[ 819.200000] [<ffffffff811f53d1>] sysfs_add_one+0xc1/0xf0
[ 819.206025] [<ffffffff811f5cf5>] sysfs_do_create_link+0x135/0x220
[ 819.212944] [<ffffffff811f7023>] ? sysfs_create_group+0x13/0x20
[ 819.219656] [<ffffffff811f5df3>] sysfs_create_link+0x13/0x20
[ 819.226109] [<ffffffff813b04f6>] bus_add_device+0xe6/0x1b0
[ 819.232350] [<ffffffff813ae7cb>] device_add+0x2db/0x460
[ 819.238300] [<ffffffffa0325634>] edac_create_dimm_object+0x84/0xf0 [edac_core]
[ 819.246460] [<ffffffffa0325e18>] edac_create_sysfs_mci_device+0xe8/0x290 [edac_core]
[ 819.255215] [<ffffffffa0322e2a>] edac_mc_add_mc+0x5a/0x2c0 [edac_core]
[ 819.262611] [<ffffffffa03412df>] sbridge_register_mci+0x1bc/0x279 [sb_edac]
[ 819.270493] [<ffffffffa03417a3>] sbridge_probe+0xef/0x175 [sb_edac]
[ 819.277630] [<ffffffff813ba4e8>] ? pm_runtime_enable+0x58/0x90
[ 819.284268] [<ffffffff812f430c>] local_pci_probe+0x5c/0xd0
[ 819.290508] [<ffffffff812f5ba1>] __pci_device_probe+0xf1/0x100
[ 819.297117] [<ffffffff812f5bea>] pci_device_probe+0x3a/0x60
[ 819.303457] [<ffffffff813b1003>] really_probe+0x73/0x270
[ 819.309496] [<ffffffff813b138e>] driver_probe_device+0x4e/0xb0
[ 819.316104] [<ffffffff813b149b>] __driver_attach+0xab/0xb0
[ 819.322337] [<ffffffff813b13f0>] ? driver_probe_device+0xb0/0xb0
[ 819.329151] [<ffffffff813af5d6>] bus_for_each_dev+0x56/0x90
[ 819.335489] [<ffffffff813b0d7e>] driver_attach+0x1e/0x20
[ 819.341534] [<ffffffff813b0980>] bus_add_driver+0x1b0/0x2a0
[ 819.347884] [<ffffffffa0347000>] ? 0xffffffffa0346fff
[ 819.353641] [<ffffffff813b19f6>] driver_register+0x76/0x140
[ 819.359980] [<ffffffff8159f18b>] ? printk+0x51/0x53
[ 819.365524] [<ffffffffa0347000>] ? 0xffffffffa0346fff
[ 819.371291] [<ffffffff812f5896>] __pci_register_driver+0x56/0xd0
[ 819.378096] [<ffffffffa0347054>] sbridge_init+0x54/0x1000 [sb_edac]
[ 819.385231] [<ffffffff8100203f>] do_one_initcall+0x3f/0x170
[ 819.391577] [<ffffffff810bcd2e>] sys_init_module+0xbe/0x230
[ 819.397926] [<ffffffff815bb529>] system_call_fastpath+0x16/0x1b
[ 819.404633] ---[ end trace 1654fdd39556689f ]---
This happens because the bus is not being properly initialized.
Instead of putting the memory sub-devices inside the memory controller,
it is putting everything under the same directory:
$ tree /sys/bus/edac/
/sys/bus/edac/
├── devices
│ ├── all_channel_counts -> ../../../devices/system/edac/mc/mc0/all_channel_counts
│ ├── csrow0 -> ../../../devices/system/edac/mc/mc0/csrow0
│ ├── csrow1 -> ../../../devices/system/edac/mc/mc0/csrow1
│ ├── csrow2 -> ../../../devices/system/edac/mc/mc0/csrow2
│ ├── dimm0 -> ../../../devices/system/edac/mc/mc0/dimm0
│ ├── dimm1 -> ../../../devices/system/edac/mc/mc0/dimm1
│ ├── dimm3 -> ../../../devices/system/edac/mc/mc0/dimm3
│ ├── dimm6 -> ../../../devices/system/edac/mc/mc0/dimm6
│ ├── inject_addrmatch -> ../../../devices/system/edac/mc/mc0/inject_addrmatch
│ ├── mc -> ../../../devices/system/edac/mc
│ └── mc0 -> ../../../devices/system/edac/mc/mc0
├── drivers
├── drivers_autoprobe
├── drivers_probe
└── uevent
On a multi-memory controller system, the names "csrow%d" and "dimm%d"
should be under "mc%d", and not at the main hierarchy level.
So, we need to create a per-MC bus, in order to have its own namespace.
Reviewed-by: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Greg K H <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As EDAC doesn't use struct device itself, it created a parent dev
pointer called as "pdev". Now that we'll be converting it to use
struct device, instead of struct devsys, this needs to be fixed.
No functional changes.
Reviewed-by: Aristeu Rozanski <arozansk@redhat.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Mark Gross <mark.gross@intel.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: Tim Small <tim@buttersideup.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Egor Martovetsky <egor@pasemi.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Joe Perches <joe@perches.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Niklas Söderlund" <niklas.soderlund@ericsson.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a new tracepoint-based hardware events report method for
reporting Memory Controller events.
Part of the description bellow is shamelessly copied from Tony
Luck's notes about the Hardware Error BoF during LPC 2010 [1].
Tony, thanks for your notes and discussions to generate the
h/w error reporting requirements.
[1] http://lwn.net/Articles/416669/
We have several subsystems & methods for reporting hardware errors:
1) EDAC ("Error Detection and Correction"). In its original form
this consisted of a platform specific driver that read topology
information and error counts from chipset registers and reported
the results via a sysfs interface.
2) mcelog - x86 specific decoding of machine check bank registers
reporting in binary form via /dev/mcelog. Recent additions make use
of the APEI extensions that were documented in version 4.0a of the
ACPI specification to acquire more information about errors without
having to rely reading chipset registers directly. A user level
programs decodes into somewhat human readable format.
3) drivers/edac/mce_amd.c - this driver hooks into the mcelog path and
decodes errors reported via machine check bank registers in AMD
processors to the console log using printk();
Each of these mechanisms has a band of followers ... and none
of them appear to meet all the needs of all users.
As part of a RAS subsystem, let's encapsulate the memory error hardware
events into a trace facility.
The tracepoint printk will be displayed like:
mc_event: [quant] (Corrected|Uncorrected|Fatal) error:[error msg] on [label] ([location] [edac_mc detail] [driver_detail]
Where:
[quant] is the quantity of errors
[error msg] is the driver-specific error message
(e. g. "memory read", "bus error", ...);
[location] is the location in terms of memory controller and
branch/channel/slot, channel/slot or csrow/channel;
[label] is the memory stick label;
[edac_mc detail] describes the address location of the error
and the syndrome;
[driver detail] is driver-specifig error message details,
when needed/provided (e. g. "area:DMA", ...)
For example:
mc_event: 1 Corrected error:memory read on memory stick DIMM_1A (mc:0 location:0:0:0 page:0x586b6e offset:0xa66 grain:32 syndrome:0x0 area:DMA)
Of course, any userspace tools meant to handle errors should not parse
the above data. They should, instead, use the binary fields provided by
the tracepoint, mapping them directly into their Management Information
Base.
NOTE: The original patch was providing an additional mechanism for
MCA-based trace events that also contained MCA error register data.
However, as no agreement was reached so far for the MCA-based trace
events, for now, let's add events only for memory errors.
A latter patch is planned to change the tracepoint, for those types
of event.
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The existing seq_printf function is rewritten in terms of the new
seq_vprintf which is also exported to modules. This allows GFS2
(and potentially other seq_file users) to have a vprintf based
interface and to avoid an extra copy into a temporary buffer in
some cases.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
We handle NULL in rt{,6}_set_peer but then our caller will try to pass
that NULL pointer into inet_putpeer() which isn't ready for it.
Fix this by moving the NULL check one level up, and then remove the
now unnecessary NULL check from inetpeer_ptr_set_peer().
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implementation can deal with having many inetpeer roots, which is
a necessary prerequisite for per-FIB table rooted peer tables.
Each family (AF_INET, AF_INET6) has a sequence number which we bump
when we get a family invalidation request.
Each peer lookup cheaply checks whether the flush sequence of the
root we are using is out of date, and if so flushes it and updates
the sequence number.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is zero point to this function.
It's only real substance is to perform an extremely outdated BSD4.2
ICMP check, which we can safely remove. If you really have a MTU
limited link being routed by a BSD4.2 derived system, here's a nickel
go buy yourself a real router.
The other actions of ip_rt_frag_needed(), checking and conditionally
updating the peer, are done by the per-protocol handlers of the ICMP
event.
TCP, UDP, et al. have a handler which will receive this event and
transmit it back into the associated route via dst_ops->update_pmtu().
This simplification is important, because it eliminates the one place
where we do not have a proper route context in which to make an
inetpeer lookup.
Signed-off-by: David S. Miller <davem@davemloft.net>
We encode the pointer(s) into an unsigned long with one state bit.
The state bit is used so we can store the inetpeer tree root to use
when resolving the peer later.
Later the peer roots will be per-FIB table, and this change works to
facilitate that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge RCU fixes from Paul E. McKenney:
" This series has four patches, the major point of which is to eliminate
some slowdowns (including boot-time slowdowns) resulting from some
RCU_FAST_NO_HZ changes. The issue with the changes is that posting timers
from the idle loop has no effect if the CPU has entered dyntick-idle
mode because the CPU has already computed its wakeup time, and posting
a timer does not cause it to be recomputed. The short-term fix is for
RCU to precompute the timeout value so that the CPU's calculation is
correct. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
fix the coding style related to mesh parameters, especially the indentation,
as pointed out by Johannes Berg.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the missing kernel-doc for mesh configuration parameters as pointed
out by Johannes Berg.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If I build with W=1, for every file that includes <net/route.h>, I get the warning
include/net/route.h: In function 'ip_route_output':
include/net/route.h:135:3: warning: initialized field overwritten [-Woverride-init]
include/net/route.h:135:3: warning: (near initialization for 'fl4') [-Woverride-init]
(This is with "gcc (Debian 4.6.3-1) 4.6.3")
A fix seems pretty trivial: move the initialization of .flowi4_tos
earlier. As far as I can tell, this has no effect on code generation.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
asm-generic/bug.h uses taint flags that are only defined in
linux/kernel.h, resulting in build failures on platforms that
don't include linux/kernel.h some other way:
arch/sh/include/asm/thread_info.h:172:2: error: 'TAINT_WARN' undeclared (first use in this function)
Caused by commit edd63a2763 ("set_restore_sigmask() is never called
without SIGPENDING (and never should be)").
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
pxa-ssp.c uses API like cpu_is_pxa3xx(), cpu_is_pxa2xx(), which is
defined under arch-pxa architecture, and drivers under mach-mmp
can't find it. so just use ssp->type to replace that API.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
add pxa910-ssp into ssp_id_table, and fix pxa-ssp compiling issue
under mach-mmp architect.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds regulator_set_voltage_time_sel(), to move into core, the
commonly used code by drivers to provide the .set_voltage_time_sel callback.
It will also allow us to configure different ramp delay for different
regulators easily.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove more custom stuff by simply converting the Nomadik machine
to use generic clocks and move the driver to drivers/clk.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mike Turquette <mturquette@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I originally sent this patch to <trivial@kernel.org>, but Jiri Kosina did
not feel that this is fully appropriate for the trivial tree.
Using linux/tcp.h from C++ results in:
cat t.cc
#include <linux/tcp.h>
int main() { }
g++ -c t.cc
In file included from t.cc:1:
/usr/include/linux/tcp.h:72: error: '__u32 __fswab32(__u32)' cannot appear in a constant-expression
/usr/include/linux/tcp.h:72: error: a function call cannot appear in a constant-expression
...
Attached trivial patch fixes this problem.
Tested:
- the t.cc above compiles with g++ and
- the following program generates the same output before/after
the patch:
#include <linux/tcp.h>
#include <stdio.h>
int main ()
{
#define P(a) printf("%s: %08x\n", #a, (int)a)
P(TCP_FLAG_CWR);
P(TCP_FLAG_ECE);
P(TCP_FLAG_URG);
P(TCP_FLAG_ACK);
P(TCP_FLAG_PSH);
P(TCP_FLAG_RST);
P(TCP_FLAG_SYN);
P(TCP_FLAG_FIN);
P(TCP_RESERVED_BITS);
P(TCP_DATA_OFFSET);
#undef P
return 0;
}
Signed-off-by: Paul Pluzhnikov <ppluzhnikov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need one interface for this operation, since we always know
which inetpeer root we want to flush.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it's guarenteed that we will access the inetpeer if we're trying
to do timewait recycling and TCP options were enabled on the
connection, just cache the peer in the timewait socket.
In the future, inetpeer lookups will be context dependent (per routing
realm), and this helps facilitate that as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few kernel-doc descriptions that were missed
during development.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The get_peer method TCP uses is full of special cases that make no
sense accommodating, and it also gets in the way of doing more
reasonable things here.
First of all, if the socket doesn't have a usable cached route, there
is no sense in trying to optimize timewait recycling.
Likewise for the case where we have IP options, such as SRR enabled,
that make the IP header destination address (and thus the destination
address of the route key) differ from that of the connection's
destination address.
Just return a NULL peer in these cases, and thus we're also able to
get rid of the clumsy inetpeer release logic.
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a lot of places that open-code rt{,6}_get_peer() only because
they want to set 'create' to one. So add an rt{,6}_get_peer_create()
for their sake.
There were also a few spots open-coding plain rt{,6}_get_peer() and
those are transformed here as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
With LE/SMP the completion of a security level elavation from medium to
high is indicated by a HCI Encryption Key Refresh Complete event. The
necessary behavior upon receiving this event is a mix of what's done for
auth_complete and encryption_change, which is also where most of the
event handling code has been copied from.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Convert calculations of proportion of writeback each bdi does to new flexible
proportion code. That allows us to use aging period of fixed wallclock time
which gives better proportion estimates given the hugely varying throughput of
different devices.
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Implement code computing proportions of events of different type (like code in
lib/proportions.c) but allowing periods to have different lengths. This allows
us to have aging periods of fixed wallclock time which gives better proportion
estimates given the hugely varying throughput of different devices - previous
measuring of aging period by number of events has the problem that a reasonable
period length for a system with low-end USB stick is not a reasonable period
length for a system with high-end storage array resulting either in too slow
proportion updates or too fluctuating proportion updates.
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
/proc/net/unix has quadratic behavior, and can hold unix_table_lock for
a while if high number of unix sockets are alive. (90 ms for 200k
sockets...)
We already have a hash table, so its quite easy to use it.
Problem is unbound sockets are still hashed in a single hash slot
(unix_socket_table[UNIX_HASH_TABLE])
This patch also spreads unbound sockets to 256 hash slots, to speedup
both /proc/net/unix and unix_diag.
Time to read /proc/net/unix with 200k unix sockets :
(time dd if=/proc/net/unix of=/dev/null bs=4k)
before : 520 secs
after : 2 secs
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add struct net as a parameter of inet_getpeer_v[4,6],
use net to replace &init_net.
and modify some places to provide net for inet_getpeer_v[4,6]
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
now inetpeer doesn't support namespace,the information will
be leaking across namespace.
this patch move the global vars v4_peers and v6_peers to
netns_ipv4 and netns_ipv6 as a field peers.
add struct pernet_operations inetpeer_ops to initial pernet
inetpeer data.
and change family_to_base and inet_getpeer to support namespace.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull perf fixes from Ingo Molnar:
"A bit larger than what I'd wish for - half of it is due to hw driver
updates to Intel Ivy-Bridge which info got recently released,
cycles:pp should work there now too, amongst other things. (but we
are generally making exceptions for hardware enablement of this type.)
There are also callchain fixes in it - responding to mostly
theoretical (but valid) concerns. The tooling side sports perf.data
endianness/portability fixes which did not make it for the merge
window - and various other fixes as well."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
perf/x86: Check user address explicitly in copy_from_user_nmi()
perf/x86: Check if user fp is valid
perf: Limit callchains to 127
perf/x86: Allow multiple stacks
perf/x86: Update SNB PEBS constraints
perf/x86: Enable/Add IvyBridge hardware support
perf/x86: Implement cycles:p for SNB/IVB
perf/x86: Fix Intel shared extra MSR allocation
x86/decoder: Fix bsr/bsf/jmpe decoding with operand-size prefix
perf: Remove duplicate invocation on perf_event_for_each
perf uprobes: Remove unnecessary check before strlist__delete
perf symbols: Check for valid dso before creating map
perf evsel: Fix 32 bit values endianity swap for sample_id_all header
perf session: Handle endianity swap on sample_id_all header data
perf symbols: Handle different endians properly during symbol load
perf evlist: Pass third argument to ioctl explicitly
perf tools: Update ioctl documentation for PERF_IOC_FLAG_GROUP
perf tools: Make --version show kernel version instead of pull req tag
perf tools: Check if callchain is corrupted
perf callchain: Make callchain cursors TLS
...
Pull drm intel and exynos fixes from Dave Airlie:
"A bunch of fixes for Intel and exynos, nothing too major, a new intel
PCI ID, and a fix for CRT detection."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: pch_irq_handler -> {ibx, cpt}_irq_handler
char/agp: add another Ironlake host bridge
drm/i915: fix up ivb plane 3 pageflips
drm/exynos: fixed blending for hdmi graphic layer
drm/exynos: Remove dummy encoder get_crtc operation implementation
drm/exynos: Keep a reference to frame buffer GEM objects
drm/exynos: Don't cast GEM object to Exynos GEM object when not needed
drm/exynos: DRIVER_BUS_PLATFORM is not a driver feature
drm/exynos: fixed size type.
drm/exynos: Use DRM_FORMAT_{NV12, YUV420} instead of DRM_FORMAT_{NV12M, YUV420M}
drm/i915: hold forcewake around ring hw init
drm/i915: Mark the ringbuffers as being in the GTT domain
drm/i915/crt: Do not rely upon the HPD presence pin
drm/i915: Reset last_retired_head when resetting ring
Instead of reading in the resource groups when gfs2 is checking
for free space to allocate from, gfs2 can store the necessary infromation
in the resource group's lvb. Also, instead of searching for unlinked
inodes in every resource group that's checked for free space, gfs2 can
store the number of unlinked but inodes in the lvb, and only check for
unlinked inodes if it will find some.
The first time a resource group is locked, the lvb must initialized.
Since this involves counting the unlinked inodes in the resource group,
this takes a little extra time. But after that, if the resource group
is locked with GL_SKIP, the buffer head won't be read in unless it's
actually needed.
Enabling the resource groups lvbs is done via the rgrplvb mount option. If
this option isn't set, the lvbs will still be set and updated, but they won't
be verfied or used by the filesystem. To safely turn on this option, all of
the nodes mounting the filesystem must be running code with this patch, and
the filesystem must have been completely unmounted since they were updated.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Intel-iommu initialization doesn't currently reserve the memory
used for the IOMMU registers. This can allow the pci resource
allocator to assign a device BAR to the same address as the
IOMMU registers. This can cause some not so nice side affects
when the driver ioremap's that region.
Introduced two helper functions to map & unmap the IOMMU
registers as well as simplify the init and exit paths.
Signed-off-by: Donald Dutile <ddutile@redhat.com>
Acked-by: Chris Wright <chrisw@redhat.com>
Cc: iommu@lists.linux-foundation.org
Cc: suresh.b.siddha@intel.com
Cc: dwmw2@infradead.org
Link: http://lkml.kernel.org/r/1338845342-12464-3-git-send-email-ddutile@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add vga_switcheroo_get_client_state() to get the current state of the
client. This is necessary to determine the proper initial state of
audio clients in HD-audio driver.
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-samsung:
drm/exynos: fixed blending for hdmi graphic layer
drm/exynos: Remove dummy encoder get_crtc operation implementation
drm/exynos: Keep a reference to frame buffer GEM objects
drm/exynos: Don't cast GEM object to Exynos GEM object when not needed
drm/exynos: DRIVER_BUS_PLATFORM is not a driver feature
drm/exynos: fixed size type.
drm/exynos: Use DRM_FORMAT_{NV12, YUV420} instead of DRM_FORMAT_{NV12M, YUV420M}
Commit 026cee0086 "params:
<level>_initcall-like kernel parameters" set old-style module
parameters to level 0. And we call those level 0 calls where we used
to, early in start_kernel().
We also loop through the initcall levels and call the levelled
module_params before the corresponding initcall. Unfortunately level
0 is early_init(), so we call the standard module_param calls twice.
(Turns out most things don't care, but at least ubi.mtd does).
Change the level to -1 for standard module_param calls.
Reported-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
The DMA controller like Nvidia's Tegra Dma controller
supports the different slave requestor id from different slave.
This need to be configure in dma controller to handle the request
properly.
Adding the slave-id in the slave configuration so that information
can be passed from client when configuring for slave.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Zero is written at clear_tid_address when the process exits. This
functionality is used by pthread_join().
We already have sys_set_tid_address() to change this address for the
current task but there is no way to obtain it from user space.
Without the ability to find this address and dump it we can't restore
pthread'ed apps which call pthread_join() once they have been restored.
This patch introduces the PR_GET_TID_ADDRESS prctl option which allows
the current process to obtain own clear_tid_address.
This feature is available iif CONFIG_CHECKPOINT_RESTORE is set.
[akpm@linux-foundation.org: fix prctl numbering]
Signed-off-by: Andrew Vagin <avagin@openvz.org>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Pedro Alves <palves@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A fix for commit b32dfe3771 ("c/r: prctl: add ability to set new
mm_struct::exe_file").
After removing mm->num_exe_file_vmas kernel keeps mm->exe_file until
final mmput(), it never becomes NULL while task is alive.
We can check for other mapped files in mm instead of checking
mm->num_exe_file_vmas, and mark mm with flag MMF_EXE_FILE_CHANGED in
order to forbid second changing of mm->exe_file.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Reviewed-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch extends the kernel's ethtool interface by adding support
for 2 new EEE commands - get_eee and set_eee.
Thanks goes to Giuseppe Cavallaro for his original patch adding this support.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mask option allows you put all address belonging that mask into
the same recent slot. This can be useful in case that recent is used
to detect attacks from the same network segment.
Tested for backward compatibility.
Signed-off-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for cttimeout.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since the sysctl data for l[3|4]proto now resides in pernet nf_proto_net.
We can now remove this unused fields from struct nf_contrack_l[3,4]proto.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for ICMPv6 protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for ICMP protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for UDP protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for TCP protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for the generic layer 4 protocol
tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch prepares the namespace support for layer 3 protocol trackers.
Basically, this modifies the following interfaces:
* nf_ct_l3proto_[un]register_sysctl.
* nf_conntrack_l3proto_[un]register.
We add a new nf_ct_l3proto_net is used to get the pernet data of l3proto.
This adds rhe new struct nf_ip_net that is used to store the sysctl header
and l3proto_ipv4,l4proto_tcp(6),l4proto_udp(6),l4proto_icmp(v6) because the
protos such tcp and tcp6 use the same data,so making nf_ip_net as a field
of netns_ct is the easiest way to manager it.
This patch also adds init_net to struct nf_conntrack_l3proto to initial
the layer 3 protocol pernet data.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch prepares the namespace support for layer 4 protocol trackers.
Basically, this modifies the following interfaces:
* nf_ct_[un]register_sysctl
* nf_conntrack_l4proto_[un]register
to include the namespace parameter. We still use init_net in this patch
to prepare the ground for follow-up patches for each layer 4 protocol
tracker.
We add a new net_id field to struct nf_conntrack_l4proto that is used
to store the pernet_operations id for each layer 4 protocol tracker.
Note that AF_INET6's protocols do not need to do sysctl compat. Thus,
we only register compat sysctl when l4proto.l3proto != AF_INET6.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Implement a new "fail-open" mode where packets are not dropped
upon queue-full condition. This mode can be enabled/disabled per
queue using netlink NFQA_CFG_FLAGS & NFQA_CFG_MASK attributes.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Vivek Kashyap <vivk@us.ibm.com>
Signed-off-by: Sridhar Samudrala <samudrala@us.ibm.com>
It was scheduled to be removed.
Cc: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It was scheduled to be removed.
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch addresses two issues:
a) Fix usage of u32 and __be32 that causes endianess warnings via sparse.
b) Ensure consistent hashing in a cluster that is composed of big and
little endian systems. Thus, we obtain the same hash mark in an
heterogeneous cluster.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add the F3 PCI id of F15h, model 0x10 to pci_ids.h and to the amd_nb
code which generates the list of northbridges on an AMD box. Shorten
define name while at it so that it fits into pci_ids.h.
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
When a CPU is entering dyntick-idle mode, tick_nohz_stop_sched_tick()
calls rcu_needs_cpu() see if RCU needs that CPU, and, if not, computes the
next wakeup time based on the timer wheels. Only later, when actually
entering the idle loop, rcu_prepare_for_idle() will be invoked. In some
cases, rcu_prepare_for_idle() will post timers to wake the CPU back up.
But all for naught: The next wakeup time for the CPU has already been
computed, and posting a timer afterwards does not force that wakeup
time to be recomputed. This means that rcu_prepare_for_idle()'s have
no effect.
This is not a problem on a busy system because something else will wake
up the CPU soon enough. However, on lightly loaded systems, the CPU
might stay asleep for a considerable length of time. If that CPU has
a callback that the rest of the system is waiting on, the system might
run very slowly or (in theory) even hang.
This commit avoids this problem by having rcu_needs_cpu() give
tick_nohz_stop_sched_tick() an estimate of when RCU will need the CPU
to wake back up, which tick_nohz_stop_sched_tick() takes into account
when programming the CPU's wakeup time. An alternative approach is
for rcu_prepare_for_idle() to use hrtimers instead of normal timers,
but timers are much more efficient than are hrtimers for frequently
and repeatedly posting and cancelling a given timer, which is exactly
what RCU_FAST_NO_HZ does.
Reported-by: Pascal Chapperon <pascal.chapperon@wanadoo.fr>
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Tested-by: Pascal Chapperon <pascal.chapperon@wanadoo.fr>
In the current code, a short dyntick-idle interval (where there is
at least one non-lazy callback on the CPU) and a long dyntick-idle
interval (where there are only lazy callbacks on the CPU) are traced
identically, which can be less than helpful. This commit therefore
emits different event traces in these two cases.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Tested-by: Pascal Chapperon <pascal.chapperon@wanadoo.fr>
It was introduced for memcg to iterate cgroup hierarchy without
holding cgroup_mutex, but soon after that it was replaced with
a lockless way in memcg.
No one used hierarchy_mutex since that, so remove it.
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Redesign all the off-channel code, getting rid of
the generic off-channel work concept, replacing
it with a simple remain-on-channel list.
This fixes a number of small issues with the ROC
implementation:
* offloaded remain-on-channel couldn't be queued,
now we can queue it as well, if needed
* in iwlwifi (the only user) offloaded ROC is
mutually exclusive with scanning, use the new
queue to handle that case -- I expect that it
will later depend on a HW flag
The bigger issue though is that there's a bad bug
in the current implementation: if we get a mgmt
TX request while HW roc is active, and this new
request has a wait time, we actually schedule a
software ROC instead since we can't guarantee the
existing offloaded ROC will still be that long.
To fix this, the queuing mechanism was needed.
The queuing mechanism for offloaded ROC isn't yet
optimal, ideally we should add API to have the HW
extend the ROC if needed. We could add that later
but for now use a software implementation.
Overall, this unifies the behaviour between the
offloaded and software-implemented case as much
as possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IDLE handling in HW off-channel is broken right
now since we turn off IDLE only when the off-channel
period already started. Therefore, all drivers that
use it today (only iwlwifi!) must support off-channel
while idle, so playing with idle isn't needed at all.
Off-channel in general, since it's no longer used for
authentication/association, shouldn't affect PS, so
also remove that logic.
Also document a small caveat for reporting TX status
from off-channel frames in HW remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The remain-on-channel time validation shouldn't
depend on the value of HZ, as it does now with
the check against jiffies, since then you might
use a value that works on one system but not on
another. Fix it by checking against a minimum
that's fixed.
Also add validation of the wait duration for a
management frame TX since this also translates
into remain-on-channel internally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I found this core on a BCM4322, a PCI card in the Linksys WRT610N V1.
This core is not used by the driver, this patch just makes ssb show the
correct name.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we've removed all uses of the set_channel
API except for the monitor channel and in libertas,
clarify this. Split the libertas mesh use into a
new libertas_set_mesh_channel() operation, just to
keep backward compatibility, and rename the normal
set_channel() to set_monitor_channel().
Also describe the desired set_monitor_channel()
semantics more clearly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull ACPI and Power Management changes from Len Brown.
This does an evil merge to fix up what I think is a mismerge by Len to
the gma500 driver, and restore it to the mainline state.
In that driver, both branches had commented out the call to
acpi_video_register(), and Len resolved the merge to that commented-out
version.
However, in mainline, further changes by Alan (commit d839ede47a56:
"gma500: opregion and ACPI" to be exact) had re-enabled the ACPI video
registration, so the current state of the driver seems to want it.
Alan is apparently still feeling the effects of partying with the Queen,
so he didn't reply to my query, but I'll do the evil merge anyway.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
ACPI: fix acpi_bus.h build warnings when ACPI is not enabled
drivers: acpi: Fix dependency for ACPI_HOTPLUG_CPU
tools/power turbostat: fix IVB support
tools/power turbostat: fix un-intended affinity of forked program
ACPI video: use after input_unregister_device()
gma500: don't register the ACPI video bus
acpi_video: Intel video is not always i915
acpi_video: fix leaking PCI references
ACPI: Ignore invalid _PSS entries, but use valid ones
ACPI battery: only refresh the sysfs files when pertinent information changes
commit 5faa5df1fa (inetpeer: Invalidate the inetpeer tree along with
the routing cache) added a race :
Before freeing an inetpeer, we must respect a RCU grace period, and make
sure no user will attempt to increase refcnt.
inetpeer_invalidate_tree() waits for a RCU grace period before inserting
inetpeer tree into gc_list and waking the worker. At that time, no
concurrent lookup can find a inetpeer in this tree.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rdpmc instruction is faster than the equivelant rdmsr call,
so use it when possible in the kernel.
The perfctr kernel patches did this, after extensive testing showed
rdpmc to always be faster (One can look in etc/costs in the perfctr-2.6
package to see a historical list of the overhead).
I have done some tests on a 3.2 kernel, the kernel module I used
was included in the first posting of this patch:
rdmsr rdpmc
Core2 T9900: 203.9 cycles 30.9 cycles
AMD fam0fh: 56.2 cycles 9.8 cycles
Atom 6/28/2: 129.7 cycles 50.6 cycles
The speedup of using rdpmc is large.
[ It's probably possible (and desirable) to do this without
requiring a new field in the hw_perf_event structure, but
the fixed events make this tricky. ]
Signed-off-by: Vince Weaver <vweaver1@eecs.utk.edu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1203011724030.26934@cl320.eecs.utk.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Kill the no longer needed uprobes_srcu/uprobe_srcu_id code.
It doesn't really work anyway. synchronize_srcu() can only
synchronize with the code "inside" the
srcu_read_lock/srcu_read_unlock section, while
uprobe_pre_sstep_notifier() does srcu_read_lock() _after_ we
already hit the breakpoint.
I guess this probably works "in practice". synchronize_srcu() is
slow and it implies synchronize_sched(), and the probed task
enters the non- preemptible section at the start of exception
handler. Still this is not right at least in theory, and
task->uprobe_srcu_id blows task_struct.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anton Arapov <anton@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120529193008.GG8057@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Weird topologies can lead to asymmetric domain setups. This needs
further consideration since these setups are typically non-minimal
too.
For now, make it work by adding an extra mask selecting which CPUs
are allowed to iterate up.
The topology that triggered it is the one from David Rientjes:
10 20 20 30
20 10 20 20
20 20 10 20
30 20 20 10
resulting in boxes that wouldn't even boot.
Reported-by: David Rientjes <rientjes@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-3p86l9cuaqnxz7uxsojmz5rm@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ceph_con_revoke_message() is passed both a message and a ceph
connection. A ceph_msg allocated for incoming messages on a
connection always has a pointer to that connection, so there's no
need to provide the connection when revoking such a message.
Note that the existing logic does not preclude the message supplied
being a null/bogus message pointer. The only user of this interface
is the OSD client, and the only value an osd client passes is a
request's r_reply field. That is always non-null (except briefly in
an error path in ceph_osdc_alloc_request(), and that drops the
only reference so the request won't ever have a reply to revoke).
So we can safely assume the passed-in message is non-null, but add a
BUG_ON() to make it very obvious we are imposing this restriction.
Rename the function ceph_msg_revoke_incoming() to reflect that it is
really an operation on an incoming message.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
ceph_con_revoke() is passed both a message and a ceph connection.
Now that any message associated with a connection holds a pointer
to that connection, there's no need to provide the connection when
revoking a message.
This has the added benefit of precluding the possibility of the
providing the wrong connection pointer. If the message's connection
pointer is null, it is not being tracked by any connection, so
revoking it is a no-op. This is supported as a convenience for
upper layers, so they can revoke a message that is not actually
"in flight."
Rename the function ceph_msg_revoke() to reflect that it is really
an operation on a message, not a connection.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
When a ceph message is queued for sending it is placed on a list of
pending messages (ceph_connection->out_queue). When they are
actually sent over the wire, they are moved from that list to
another (ceph_connection->out_sent). When acknowledgement for the
message is received, it is removed from the sent messages list.
During that entire time the message is "in the possession" of a
single ceph connection. Keep track of that connection in the
message. This will be used in the next patch (and is a helpful
bit of information for debugging anyway).
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Move the initialization of a ceph connection's private pointer,
operations vector pointer, and peer name information into
ceph_con_init(). Rearrange the arguments so the connection pointer
is first. Hide the byte-swapping of the peer entity number inside
ceph_con_init()
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
A monitor client has a pointer to a ceph connection structure in it.
This is the only one of the three ceph client types that do it this
way; the OSD and MDS clients embed the connection into their main
structures. There is always exactly one ceph connection for a
monitor client, so there is no need to allocate it separate from the
monitor client structure.
So switch the ceph_mon_client structure to embed its
ceph_connection structure.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
SDIO_CCCR_IF[1:0] in SDIO card is used for card data bus width
setting as below:
00b: 1-bit bus
01b: Reserved
10b: 4-bit bus
11b: 8-bit bus (only for embedded SDIO)
And sdio_enable_wide is for setting data bus width as 4-bit.
But currently, it first reads the register, second OR' 1b with
SDIO_CCCR_IF[1], and then writes it back.
As we can see, this is based on such assumption that the
SDIO_CCCR_IF[0] is always 0. Apparently, this is not right.
Signed-off-by: Yong Ding <yongd@marvell.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Alex says:
"Changes this time include:
- Generalize KVM_GUEST support to overall ePAPR code
- Fix reset for Book3S HV
- Fix machine check deferral when CONFIG_KVM_GUEST=y
- Add support for BookE register DECAR"
* 'for-upstream' of git://github.com/agraf/linux-2.6:
KVM: PPC: Not optimizing MSR_CE and MSR_ME with paravirt.
KVM: PPC: booke: Added DECAR support
KVM: PPC: Book3S HV: Make the guest hash table size configurable
KVM: PPC: Factor out guest epapr initialization
Signed-off-by: Avi Kivity <avi@redhat.com>
Introduces a couple of print functions, which are essentially wrappers
around standard printk functions, with a KVM: prefix.
Functions introduced or modified are:
- kvm_err(fmt, ...)
- kvm_info(fmt, ...)
- kvm_debug(fmt, ...)
- kvm_pr_unimpl(fmt, ...)
- pr_unimpl(vcpu, fmt, ...) -> vcpu_unimpl(vcpu, fmt, ...)
Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds support for the "top dir" flag. Currently this is unused
but a subsequent patch is planned which will add support for the
Orlov allocation policy when allocating subdirectories in a parent
with this flag set.
In order to ensure backward compatible behaviour, mkfs.gfs2 does
not currently tag the root directory with this flag, it must always be
set manually.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Change the ns_timeout parameter of the wait ioctl to a signed value.
Doing this allows the kernel to provide an infinite wait when a timeout
of less than 0 is provided. This mimics select/poll.
Initially the parameter was meant to match up with the GL spec 1:1, but
after being made aware of how much 2^64 - 1 nanoseconds actually is, I
do not think anyone will ever notice the loss of 1 bit.
The infinite timeout on waiting is similar to the existing i915
userspace interface with the exception that struct_mutex is dropped
while doing the wait in this ioctl.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Other than ix86, x86-64 on EFI so far didn't set the
{g,s}et_wallclock accessors to the EFI routines, thus
incorrectly using raw RTC accesses instead.
Simply removing the #ifdef around the respective code isn't
enough, however: While so far early get-time calls were done in
physical mode, this doesn't work properly for x86-64, as virtual
addresses would still need to be set up for all runtime regions
(which wasn't the case on the system I have access to), so
instead the patch moves the call to efi_enter_virtual_mode()
ahead (which in turn allows to drop all code related to calling
efi-get-time in physical mode).
Additionally the earlier calling of efi_set_executable()
requires the CPA code to cope, i.e. during early boot it must be
avoided to call cpa_flush_array(), as the first thing this
function does is a BUG_ON(irqs_disabled()).
Also make the two EFI functions in question here static -
they're not being referenced elsewhere.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Matt Fleming <matt.fleming@intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/4FBFBF5F020000780008637F@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull perf fixes from Arnaldo Carvalho de Melo:
* Endianness fixes from Jiri Olsa
* Fixes for make perf tarball
* Fix for DSO name in perf script callchains, from David Ahern
* Segfault fixes for perf top --callchain, from Namhyung Kim
* Minor function result fixes from Srikar Dronamraju
* Add missing 3rd ioctl parameter, from Namhyung Kim
* Fix pager usage in minimal embedded systems, from Avik Sil
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The new commit code fails to copy the verifier into the wb_verf field
of _all_ the nfs_page structures; it only copies it into the first entry.
The consequence is that most requests end up failing to match in
nfs_commit_release.
Fix is to copy the verifier into the req->wb_verf field in
nfs_write_completion.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Fred Isaman <iisaman@netapp.com>
Just like the AP mode patch, instead of setting
the channel and then joining the mesh network,
provide the channel to join the network on to
the join_mesh() function.
Like in AP mode, you can also give the channel
to the join-mesh nl80211 command now.
Unlike AP mode, it picks a default channel if
none was given.
As libertas uses mesh mode interfaces but has
no join_mesh callback and we can't simply break
it, keep some compatibility code for that case
and configure the channel directly for it.
In the non-libertas case, where we store the
channel until join, allow setting it while the
interface is down.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of setting the channel first and then
starting the AP, let cfg80211 store the channel
and provide it as one of the AP settings.
This means that now you have to set the channel
before you can start an AP interface, but since
hostapd/wpa_supplicant always do that we're OK
with this change.
Alternatively, it's now possible to give the
channel as an attribute to the start-ap nl80211
command, overriding any preset channel.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change cfg80211_can_beacon_sec_chan() to return true
if there is no secondary channel to simplify all the
current users of it. They all check the channel type
before calling the function because it returns false
if there's no secondary channel.
Also actually document the return value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_get_operstate() was used by drivers in order to
know whether the sta link is up, but it's no longer needed
(nor used) as mac80211 notifies the drivers about
authorization changes (via the sta_state callback)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the use of #ifdef CONFIG_MAC80211_IBSS_DEBUG/#endif
by adding a logging macro to encapsulate the test.
Convert the appropriate uses too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the use of #ifdef CONFIG_MAC80211_HT_DEBUG/#endif
by adding a logging macro to encapsulate the test.
Convert the appropriate uses too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tell userspace about beacon loss event.
This event doesn't replace the deauth/disassoc that
might come if the AP is not available.
The driver can send this event in order to hint
userspace what might follow (which in turn can
use it as roaming trigger).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Low level drivers can now set certain netdev feature bits in
netdev_features member of the ieee80211_hw struct. These will be
propagated to every netdev created from this HW.
The white-listed features currently include only ones related to HW
checksumming.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull embedded i2c update from Wolfram Sang:
"This only contains one new driver which had multiple dependencies
(pinctrl, i2c-mux-rework, new devm_* functions), so I decided to wait
for rc1. Plus, it had to wait a little for the ack of a devicetree
maintainer since the bindings were not trivial enough for me to pass
through.
So, given that, I hope there is still something like the "new driver
rule", so we could have the driver in 3.5 and people can start using
it. That would make merging support for some boards easier for 3.6
since the dependency on this driver is gone then."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: Add generic I2C multiplexer using pinctrl API
Pull drm radeon fixes from Dave Airlie:
"This is just radeon fixes and a bunch of new PCI ids. The fixes are
for a deadlock, an audio regression, and a couple of audio fixes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: add new SI PCI ids
drm/radeon/kms: add new BTC PCI ids
drm/radeon/kms: add new Palm, Sumo PCI ids
drm/radeon/kms: add new Trinity PCI ids
drm/radeon: fix vm deadlocks on cayman
drm/radeon: fix gpu_init on si
drm/radeon/hdmi: don't set SEND_MAX_PACKETS bit
drm/radeon/audio: don't hardcode CRTC id
drm/radeon: make audio_init consistent across asics
This patch fixes bug in macro radix_tree_for_each_contig().
If radix_tree_next_slot() sees NULL in next slot it returns NULL, but following
radix_tree_next_chunk() switches iterating into next chunk. As result iterating
becomes non-contiguous and breaks vfs "splice" and all its users.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Reported-and-bisected-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Reported-and-bisected-by: Ondrej Zary <linux@rainbow-software.org>
Reported-bisected-and-tested-by: Toralf Förster <toralf.foerster@gmx.de>
Link: https://lkml.org/lkml/2012/6/5/64
Cc: stable <stable@vger.kernel.org> # 3.4.x
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull scheduler fixes from Ingo Molnar.
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Remove NULL assignment of dattr_cur
sched: Remove the last NULL entry from sched_feat_names
sched: Make sched_feat_names const
sched/rt: Fix SCHED_RR across cgroups
sched: Move nr_cpus_allowed out of 'struct sched_rt_entity'
sched: Make sure to not re-read variables after validation
sched: Fix SD_OVERLAP
sched: Don't try allocating memory from offline nodes
sched/nohz: Fix rq->cpu_load calculations some more
sched/x86: Use cpu_llc_shared_mask(cpu) for coregroup_mask
No users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
The open recovery code does not need to request a new value for the
mdsthreshold, and so does not allocate a struct nfs4_threshold.
The problem is that encode_getfattr_open() will still request an
mdsthreshold, and so we end up Oopsing in decode_attr_mdsthreshold.
This patch fixes encode_getfattr_open so that it doesn't request an
mdsthreshold when the caller isn't asking for one. It also fixes
decode_attr_mdsthreshold so that it errors if the server returns
an mdsthreshold that we didn't ask for (instead of Oopsing).
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Andy Adamson <andros@netapp.com>
Allow chips to provide a bank of registers for controlling the wake state
in a similar fashion to the masks and propagate the wake count to the
parent interrupt controller.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
lpage_info is created for each large level even when the memory slot is
not for RAM. This means that when we add one slot for a PCI device, we
end up allocating at least KVM_NR_PAGE_SIZES - 1 pages by vmalloc().
To make things worse, there is an increasing number of devices which
would result in more pages being wasted this way.
This patch mitigates this problem by using kvm_kvzalloc().
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
The IIO DAC drivers are in a reasonably good shape. They all make use of channel
spec and non of them provides non-documented sysfs attributes. Code style should
be OK as well, both checkpatch and coccicheck only report trivial issues.
So lets move the whole folder out of staging.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We often have the case were we do have a enum style channel attribute. These
attributes have in common that they are a list of string values which usually
map in a 1-to-1 fashion to integer values.
This patch implements some common helper code for implementing enum style
channel attributes using extended channel attributes. The helper functions take
care of converting between the string and integer values, as well providing a
function for "_available" attributes which list all available enum items.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add the iio_device_get() function, which increases the reference
count of a iio device. The matching function to decrease the reference count -
iio_device_put() - already exists.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes since V1:
Apply Jonathan's review feedback:
Introduce and use IIO_ALTVOLTAGE.
Fix up comments and documentation.
Remove dead code.
Reorder some code fragments.
Add missing iio_device_free.
Convert to new API.
Fix-up out of staging includes.
Removed pll_locked attribute.
Changes since V2:
Use module_spi_driver.
adf4350_remove: move gpio_free after regulator.
target patch to drivers/iio
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes since V1:
Apply Jonathan's review feedback:
Revise device status attribute names, and split documentation into two sections.
Add additional comments, and fix indention issues.
Remove pointless zero initializations.
Revise return value handling.
Simplify some code sections.
Split store_eeprom and sync handling into separate functions.
Use strtobool where applicable.
Document platform data structures using kernel-doc style.
Use dev_to_iio_dev
write_raw IIO_CHAN_INFO_FREQUENCY: Reject values <= 0
Make patch target drivers/iio
Changes since V2:
Use for_each_clear_bit() and __set_bit() where applicable.
Add descriptive comment.
Avoid temporary for struct regulator.
spi_device_id name use ad9523-1, ad9523 will be added later.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A2MP doesn't use part of the L2CAP chan ops API so we just create general
empty function instead of the A2MP specific one.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch renames L2CAP_LE_DEFAULT_MTU macro to L2CAP_LE_MIN_MTU
since it represents the minimum MTU value, not the default MTU
value for LE.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Those are not used anywhere in code (and never were since introduction
in 2006) so just remove them.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
A2MP fixed channel do not have sk
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
A2MP status codes copied from Bluez patch sent by Peter Krystad
<pkrystad@codeaurora.org>.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Helper function to build and send A2MP messages.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Define AMP Manager and some basic functions.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This move socket specific code to l2cap_sock.c.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This remove a bit more of socket code from l2cap core, this calls set the
SOCK_ZAPPED and do some clean up depending on the socket state.
Reported-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use chan instead of void * makes more sense here.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add HCI commands to deal with Bluetooth AMP controllers.
Those commands will be used by bluetooth and softamp code.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Define assigned Protocol and Service Multiplexor (PSM) identifiers
and use them instead of magic numbers.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Define Continuation flag which the only flag used from Flags field
in L2CAP Configuration Request and Response.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Most of the include were unnecessary or already included by some other
header.
Replace module.h by export.h where possible.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix all warning and errors reported by checkpatch but license trailing
whitespace and bdaddr_t definition.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove magic number with defined link key size.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
HCI_QUIRK_NO_RESET name is misleading - purpose of this quirk is to
reset device on close instead of init, not to not reset at all.
Rename it to HCI_QUIRK_RESET_ON_CLOSE to avoid confusion.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that l2cap_ctrl is used to set up control fields, these macros are
not needed.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The ERTM specification requires the retransmit timer to be cancelled
when the monitor timer is set. The retransmit timer cannot be set
again while the monitor timer is pending.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This deletes the receive code that had handlers for each frame type at
the top level, and then had logic to determine the receive state
within each handler.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This fixes a regression from commit
2ead70b839 that is present in all
kernels starting at v3.0.
When L2CAP information was moved to struct l2cap_chan, a check was
added to l2cap_chan_del to avoid certain cleanup operations when ERTM
or streaming mode had not yet been initialized. The logic in the
check did not take in to account that chan->conf_state is set to 0 in
l2cap_chan_ready, so l2cap_chan_del failed to cancel timers and leaked
memory any time the ERTM queues or lists were not empty.
This change makes sure that l2cap_chan_del only returns early if
ERTM initialization was not performed.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
size type of drm_exynos_gem_mmap struct is changed to uint64_t and
it adds pad for the struct to be aligned as 64bit.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This routine will be called by drivers whenever they receive data in target
mode. This should be unexpected events and as such should be handled by a
standalone API (i.e. not as a callback pointer from an existing API).
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Userspace gets a netlink event upon target mode activation.
The LLCP layer is also signaled when we get an ATR_REQ in order to get
the remote general bytes.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In some environments, dramatic performance savings may be obtained because
swapped pages are saved in RAM (or a RAM-like device) instead of a swap disk.
This tag provides the basic infrastructure along with some changes to the
existing backends.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJPsorBAAoJEFjIrFwIi8fJcz8H/RBXCtFo0kiJmRked3nMAIDO
/2zN/q/Qawsg9aeoGlP7G8hQi9PMipbhQj3ixHyCTMv0zMbH988GXbBce+gIcg6e
TOQi7xXAuPEwLizmSpiTv84XzN5bMgu1oJXEqIXw0EIpuZAmp+9m/o3WBwEAtyxi
B+hvjE7eZM8f75K3lxs6sOtmIcERj9zqmT933Y8+i9iiuRyGMey2SyKtvVLbYZ+j
HroFMUi0so5TzxT/cpkRiHu0U75c651o+LV00zh7InMqbwyRsWlKTf53k8Q/q2WP
I7dVmfItwN/TpOrYTfxglYFlbYuUP35ziFvZ2trd6hcs9RK8OuKw+OmBLReHTtc=
=x9Vp
-----END PGP SIGNATURE-----
Merge tag 'stable/frontswap.v16-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm
Pull frontswap feature from Konrad Rzeszutek Wilk:
"Frontswap provides a "transcendent memory" interface for swap pages.
In some environments, dramatic performance savings may be obtained
because swapped pages are saved in RAM (or a RAM-like device) instead
of a swap disk. This tag provides the basic infrastructure along with
some changes to the existing backends."
Fix up trivial conflict in mm/Makefile due to removal of swap token code
changing a line next to the new frontswap entry.
This pull request came in before the merge window even opened, it got
delayed to after the merge window by me just wanting to make sure it had
actual users. Apparently IBM is using this on their embedded side, and
Jan Beulich says that it's already made available for SLES and OpenSUSE
users.
Also acked by Rik van Riel, and Konrad points to other people liking it
too. So in it goes.
By Dan Magenheimer (4) and Konrad Rzeszutek Wilk (2)
via Konrad Rzeszutek Wilk
* tag 'stable/frontswap.v16-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm:
frontswap: s/put_page/store/g s/get_page/load
MAINTAINER: Add myself for the frontswap API
mm: frontswap: config and doc files
mm: frontswap: core frontswap functionality
mm: frontswap: core swap subsystem hooks and headers
mm: frontswap: add frontswap header file
Pull timer updates from Thomas Gleixner:
"The clocksource driver is pure hardware enablement and the skew option
is default off, well tested and non dangerous."
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Move skew_tick option into the HIGH_RES_TIMER section
clocksource: em_sti: Add DT support
clocksource: em_sti: Emma Mobile STI driver
clockevents: Make clockevents_config() a global symbol
tick: Add tick skew boot option
Adding socket backlog len in INET_DIAG_SKMEMINFO is really useful to
diagnose various TCP problems.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is useful for SoCs whose I2C module's signals can be routed to
different sets of pins at run-time, using the pinctrl API.
+-----+ +-----+
| dev | | dev |
+------------------------+ +-----+ +-----+
| SoC | | |
| /----|------+--------+
| +---+ +------+ | child bus A, on first set of pins
| |I2C|---|Pinmux| |
| +---+ +------+ | child bus B, on second set of pins
| \----|------+--------+--------+
| | | | |
+------------------------+ +-----+ +-----+ +-----+
| dev | | dev | | dev |
+-----+ +-----+ +-----+
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
* Fix a merge conflict in mm/slub.c::acquire_slab() due to commit 02d7633
("slub: fix a memory leak in get_partial_node()").
Conflicts:
mm/slub.c
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Changed acpi_bus_hot_remove_device() to support _OST. This function is
also changed to global so that it can be called from hotplug notify
handlers to perform hot-remove operation.
Changed acpi_eject_store(), which is the sysfs eject handler. It checks
eject_pending to see if the request was originated from ACPI eject
notification. If not, it calls _OST(0x103,84,) per Figure 6-37 in ACPI
5.0 spec.
Added eject_pending bit to acpi_device_flags. This bit is set when the
kernel has received an ACPI eject notification, but does not initiate
its hot-remove operation by itself.
Added struct acpi_eject_event. This structure is used to pass extended
information to acpi_bus_hot_remove_device(), which has a single argument
to support asynchronous call
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added acpi_evaluate_hotplug_opt(). All ACPI hotplug handlers must call
this function when evaluating _OST for hotplug operations. If the
platform does not support _OST, this function returns AE_NOT_FOUND and
has no effect on the platform.
ACPI_HOTPLUG_OST is defined when all relevant ACPI hotplug operations,
such as CPU, memory and container hotplug, are enabled. This assures
consistent behavior among the hotplug operations with regarding the
_OST support. When ACPI_HOTPLUG_OST is not defined, this function is
a no-op.
ACPI PCI hotplug is not enhanced to support _OST at this time since it
is a legacy method being replaced by PCIe native hotplug. _OST support
for ACPI PCI hotplug may be added in future if necessary.
Some platforms may require the OS to support _OST in order to support
ACPI hotplug operations. For example, if a platform has the management
console where user can request a hotplug operation from, this _OST
support would be required for the management console to show the result
of the hotplug request to user.
Added macro definitions of _OST source events and status codes.
Also renamed OSC_SB_CPUHP_OST_SUPPORT to OSC_SB_HOTPLUG_OST_SUPPORT
since this _OSC bit is not specific to CPU hotplug. This bit is
defined in Table 6-147 of ACPI 5.0 as follows.
Bits: 3
Field Name: Insertion / Ejection _OST Processing Support
Definition: This bit is set if OSPM will evaluate the _OST
object defined under a device when processing
insertion and ejection source event codes.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
introduced in Linux-3.5-rc1 by
66886d6f8c
(ACPI: Add stubs for (un)register_acpi_bus_type)
Fix header file warnings when CONFIG_ACPI is not enabled:
include/acpi/acpi_bus.h:443:42: warning: 'struct acpi_bus_type' declared inside parameter list
include/acpi/acpi_bus.h:443:42: warning: its scope is only this definition or declaration, which is probably not
include/acpi/acpi_bus.h:444:44: warning: 'struct acpi_bus_type' declared inside parameter list
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit 5ceb9ce6fe.
That commit seems to be the cause of the mm compation list corruption
issues that Dave Jones reported. The locking (or rather, absense
there-of) is dubious, as is the use of the 'page' variable once it has
been found to be outside the pageblock range.
So revert it for now, we can re-visit this for 3.6. If we even need to:
as Minchan Kim says, "The patch wasn't a bug fix and even test workload
was very theoretical".
Reported-and-tested-by: Dave Jones <davej@redhat.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The comment above it says "Stat data, not accessed from path walking",
but in fact some of inode fields we use for the common stat data was way
down at the end of the inode, causing unnecessary cache misses for the
common stat operations.
The inode structure is pretty big, and this can change padding depending
on field width, but at least on the common 64-bit configurations this
doesn't change the size. Some of our inode layout has historically been
to tro to avoid unnecessary padding fields, but cache locality is at
least as important for layout, if not more.
Noticed by looking at kernel profiles, and noticing that the "i_blkbits"
access stood out like a sore thumb.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some regulator hardware use table based mapping can set volt_table in
regulator_desc and use regulator_list_voltage_table() for their list_voltage
callback.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a field to struct regmap_bus that allows bus drivers to request that
register addresses and values be formatted with a specific endianness.
The default endianness is unchanged from current operation: Big.
Implement native endian formatting/parsing for 16- and 32-bit values.
This will be enough to support regmap-mmio.c.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Control type added for cases where a specific range of values
within a register are required for control.
Added convenience macros:
SOC_SINGLE_RANGE
SOC_SINGLE_RANGE_TLV
Added accessor implementations:
snd_soc_info_volsw_range
snd_soc_put_volsw_range
snd_soc_get_volsw_range
Signed-off-by: Michal Hajduk <Michal.Hajduk@diasemi.com>
Signed-off-by: Adam Thomson <Adam.Thomson@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Prior to this patch, the CPU side of a DAI link was specified using a
single name. Often, this was the result of calling dev_name() on the
device providing the DAI, but in the case of a CPU DAI driver that
provided multiple DAIs, it needed to mix together both the device name
and some device-relative name, in order to form a single globally unique
name.
However, the CODEC side of the DAI link was specified using separate
fields for device (name or OF node) and device-relative DAI name.
This patch allows the CPU side of a DAI link to be specified in the same
way as the CODEC side, separating concepts of device and device-relative
DAI name.
I believe this will be important in multi-codec and/or dynamic PCM
scenarios, where a single CPU driver provides multiple DAIs, while also
booting using device tree, with accompanying desire not to hard-code the
CPU side device's name into the original .cpu_dai_name field.
Ideally, both the CPU DAI and CODEC DAI loops in soc_bind_dai_link()
would now be identical. However, two things prevent that at present:
1) The need to save rtd->codec for the CODEC side, which means we have
to search for the CODEC explicitly, and not just the CODEC side DAI.
2) Since we know the CODEC side DAI is part of a codec, and not just
a standalone DAI, it's slightly more efficient to convert .codec_name/
.codec_of_node into a codec first, and then compare each DAI's .codec
field, since this avoids strcmp() on each DAI's CODEC's name within
the loop.
However, the two loops are essentially semantically equivalent.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds a supply-widget variant for connection to the clock-framework.
This widget-type corresponds to the variant for regulators.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds a function getting the stream-name as a string for
a specific stream.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull networking updates from David Miller:
1) Make syn floods consume significantly less resources by
a) Not pre-COW'ing routing metrics for SYN/ACKs
b) Mirroring the device queue mapping of the SYN for the SYN/ACK
reply.
Both from Eric Dumazet.
2) Fix calculation errors in Byte Queue Limiting, from Hiroaki SHIMODA.
3) Validate the length requested when building a paged SKB for a
socket, so we don't overrun the page vector accidently. From Jason
Wang.
4) When netlabel is disabled, we abort all IP option processing when we
see a CIPSO option. This isn't the right thing to do, we should
simply skip over it and continue processing the remaining options
(if any). Fix from Paul Moore.
5) SRIOV fixes for the mellanox driver from Jack orgenstein and Marcel
Apfelbaum.
6) 8139cp enables the receiver before the ring address is properly
programmed, which potentially lets the device crap over random
memory. Fix from Jason Wang.
7) e1000/e1000e fixes for i217 RST handling, and an improper buffer
address reference in jumbo RX frame processing from Bruce Allan and
Sebastian Andrzej Siewior, respectively.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
fec_mpc52xx: fix timestamp filtering
mcs7830: Implement link state detection
e1000e: fix Rapid Start Technology support for i217
e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats()
r8169: call netif_napi_del at errpaths and at driver unload
tcp: reflect SYN queue_mapping into SYNACK packets
tcp: do not create inetpeer on SYNACK message
8139cp/8139too: terminate the eeprom access with the right opmode
8139cp: set ring address before enabling receiver
cipso: handle CIPSO options correctly when NetLabel is disabled
net: sock: validate data_len before allocating skb in sock_alloc_send_pskb()
bql: Avoid possible inconsistent calculation.
bql: Avoid unneeded limit decrement.
bql: Fix POSDIFF() to integer overflow aware.
net/mlx4_core: Fix obscure mlx4_cmd_box parameter in QUERY_DEV_CAP
net/mlx4_core: Check port out-of-range before using in mlx4_slave_cap
net/mlx4_core: Fixes for VF / Guest startup flow
net/mlx4_en: Fix improper use of "port" parameter in mlx4_en_event
net/mlx4_core: Fix number of EQs used in ICM initialisation
net/mlx4_core: Fix the slave_id out-of-range test in mlx4_eq_int
This reverts the tty layer change to use per-tty locking, because it's
not correct yet, and fixing it will require some more deep surgery.
The main revert is d29f3ef39b ("tty_lock: Localise the lock"), but
there are several smaller commits that built upon it, they also get
reverted here. The list of reverted commits is:
fde86d3108 - tty: add lockdep annotations
8f6576ad47 - tty: fix ldisc lock inversion trace
d3ca8b64b9 - pty: Fix lock inversion
b1d679afd7 - tty: drop the pty lock during hangup
abcefe5fc3 - tty/amiserial: Add missing argument for tty_unlock()
fd11b42e35 - cris: fix missing tty arg in wait_event_interruptible_tty call
d29f3ef39b - tty_lock: Localise the lock
The revert had a trivial conflict in the 68360serial.c staging driver
that got removed in the meantime.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SPEAr platforms now support DT and so must convert all drivers to support
DT. This patch adds DT probing support for SPEAr thermal sensor driver
and updates its documentation too.
Also, as SPEAr is the only user of this driver and is only available with
DT, make this an only DT driver. So, platform_data is completely removed
and passed via DT now.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Adds cpuidle_coupled_parallel_barrier, which can be used by coupled
cpuidle state enter functions to handle resynchronization after
determining if any cpu needs to abort. The normal use case will
be:
static bool abort_flag;
static atomic_t abort_barrier;
int arch_cpuidle_enter(struct cpuidle_device *dev, ...)
{
if (arch_turn_off_irq_controller()) {
/* returns an error if an irq is pending and would be lost
if idle continued and turned off power */
abort_flag = true;
}
cpuidle_coupled_parallel_barrier(dev, &abort_barrier);
if (abort_flag) {
/* One of the cpus didn't turn off it's irq controller */
arch_turn_on_irq_controller();
return -EINTR;
}
/* continue with idle */
...
}
This will cause all cpus to abort idle together if one of them needs
to abort.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On some ARM SMP SoCs (OMAP4460, Tegra 2, and probably more), the
cpus cannot be independently powered down, either due to
sequencing restrictions (on Tegra 2, cpu 0 must be the last to
power down), or due to HW bugs (on OMAP4460, a cpu powering up
will corrupt the gic state unless the other cpu runs a work
around). Each cpu has a power state that it can enter without
coordinating with the other cpu (usually Wait For Interrupt, or
WFI), and one or more "coupled" power states that affect blocks
shared between the cpus (L2 cache, interrupt controller, and
sometimes the whole SoC). Entering a coupled power state must
be tightly controlled on both cpus.
The easiest solution to implementing coupled cpu power states is
to hotplug all but one cpu whenever possible, usually using a
cpufreq governor that looks at cpu load to determine when to
enable the secondary cpus. This causes problems, as hotplug is an
expensive operation, so the number of hotplug transitions must be
minimized, leading to very slow response to loads, often on the
order of seconds.
This file implements an alternative solution, where each cpu will
wait in the WFI state until all cpus are ready to enter a coupled
state, at which point the coupled state function will be called
on all cpus at approximately the same time.
Once all cpus are ready to enter idle, they are woken by an smp
cross call. At this point, there is a chance that one of the
cpus will find work to do, and choose not to enter idle. A
final pass is needed to guarantee that all cpus will call the
power state enter function at the same time. During this pass,
each cpu will increment the ready counter, and continue once the
ready counter matches the number of online coupled cpus. If any
cpu exits idle, the other cpus will decrement their counter and
retry.
To use coupled cpuidle states, a cpuidle driver must:
Set struct cpuidle_device.coupled_cpus to the mask of all
coupled cpus, usually the same as cpu_possible_mask if all cpus
are part of the same cluster. The coupled_cpus mask must be
set in the struct cpuidle_device for each cpu.
Set struct cpuidle_device.safe_state to a state that is not a
coupled state. This is usually WFI.
Set CPUIDLE_FLAG_COUPLED in struct cpuidle_state.flags for each
state that affects multiple cpus.
Provide a struct cpuidle_state.enter function for each state
that affects multiple cpus. This function is guaranteed to be
called on all cpus at approximately the same time. The driver
should ensure that the cpus all abort together if any cpu tries
to abort once the function is called.
update1:
cpuidle: coupled: fix count of online cpus
online_count was never incremented on boot, and was also counting
cpus that were not part of the coupled set. Fix both issues by
introducting a new function that counts online coupled cpus, and
call it from register as well as the hotplug notifier.
update2:
cpuidle: coupled: fix decrementing ready count
cpuidle_coupled_set_not_ready sometimes refuses to decrement the
ready count in order to prevent a race condition. This makes it
unsuitable for use when finished with idle. Add a new function
cpuidle_coupled_set_done that decrements both the ready count and
waiting count, and call it after idle is complete.
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Trinabh Gupta <g.trinabh@gmail.com>
Cc: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
It includes:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=tmIU
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
video: bfin_adv7393fb: Fix cleanup code
video: exynos_dp: reduce delay time when configuring video setting
video: exynos_dp: move sw reset prioir to enabling sw defined function
video: exynos_dp: use devm_ functions
fb: handle NULL pointers in framebuffer release
OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
OMAPDSS: Apply VENC timings even if panel is disabled
OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
OMAPDSS: DISPC: Support rotation through TILER
OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
OMAPFB: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
video: exynos mipi dsi: support reverse panel type
video: exynos mipi dsi: Properly interpret the interrupt source flags
video: exynos mipi dsi: Avoid races in probe()
...
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
Pull third pile of signal handling patches from Al Viro:
"This time it's mostly helpers and conversions to them; there's a lot
of stuff remaining in the tree, but that'll either go in -rc2
(isolated bug fixes, ideally via arch maintainers' trees) or will sit
there until the next cycle."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
x86: get rid of calling do_notify_resume() when returning to kernel mode
blackfin: check __get_user() return value
whack-a-mole with TIF_FREEZE
FRV: Optimise the system call exit path in entry.S [ver #2]
FRV: Shrink TIF_WORK_MASK [ver #2]
FRV: Prevent syscall exit tracing and notify_resume at end of kernel exceptions
new helper: signal_delivered()
powerpc: get rid of restore_sigmask()
most of set_current_blocked() callers want SIGKILL/SIGSTOP removed from set
set_restore_sigmask() is never called without SIGPENDING (and never should be)
TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set
don't call try_to_freeze() from do_signal()
pull clearing RESTORE_SIGMASK into block_sigmask()
sh64: failure to build sigframe != signal without handler
openrisc: tracehook_signal_handler() is supposed to be called on success
new helper: sigmask_to_save()
new helper: restore_saved_sigmask()
new helpers: {clear,test,test_and_clear}_restore_sigmask()
HAVE_RESTORE_SIGMASK is defined on all architectures now
When NetLabel is not enabled, e.g. CONFIG_NETLABEL=n, and the system
receives a CIPSO tagged packet it is dropped (cipso_v4_validate()
returns non-zero). In most cases this is the correct and desired
behavior, however, in the case where we are simply forwarding the
traffic, e.g. acting as a network bridge, this becomes a problem.
This patch fixes the forwarding problem by providing the basic CIPSO
validation code directly in ip_options_compile() without the need for
the NetLabel or CIPSO code. The new validation code can not perform
any of the CIPSO option label/value verification that
cipso_v4_validate() does, but it can verify the basic CIPSO option
format.
The behavior when NetLabel is enabled is unchanged.
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs changes from Al Viro.
"A lot of misc stuff. The obvious groups:
* Miklos' atomic_open series; kills the damn abuse of
->d_revalidate() by NFS, which was the major stumbling block for
all work in that area.
* ripping security_file_mmap() and dealing with deadlocks in the
area; sanitizing the neighborhood of vm_mmap()/vm_munmap() in
general.
* ->encode_fh() switched to saner API; insane fake dentry in
mm/cleancache.c gone.
* assorted annotations in fs (endianness, __user)
* parts of Artem's ->s_dirty work (jff2 and reiserfs parts)
* ->update_time() work from Josef.
* other bits and pieces all over the place.
Normally it would've been in two or three pull requests, but
signal.git stuff had eaten a lot of time during this cycle ;-/"
Fix up trivial conflicts in Documentation/filesystems/vfs.txt (the
'truncate_range' inode method was removed by the VM changes, the VFS
update adds an 'update_time()' method), and in fs/btrfs/ulist.[ch] (due
to sparse fix added twice, with other changes nearby).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (95 commits)
nfs: don't open in ->d_revalidate
vfs: retry last component if opening stale dentry
vfs: nameidata_to_filp(): don't throw away file on error
vfs: nameidata_to_filp(): inline __dentry_open()
vfs: do_dentry_open(): don't put filp
vfs: split __dentry_open()
vfs: do_last() common post lookup
vfs: do_last(): add audit_inode before open
vfs: do_last(): only return EISDIR for O_CREAT
vfs: do_last(): check LOOKUP_DIRECTORY
vfs: do_last(): make ENOENT exit RCU safe
vfs: make follow_link check RCU safe
vfs: do_last(): use inode variable
vfs: do_last(): inline walk_component()
vfs: do_last(): make exit RCU safe
vfs: split do_lookup()
Btrfs: move over to use ->update_time
fs: introduce inode operation ->update_time
reiserfs: get rid of resierfs_sync_super
reiserfs: mark the superblock as dirty a bit later
...
The major new feature added in this update is Darrick J. Wong's
metadata checksum feature, which adds crc32 checksums to ext4's
metadata fields. There is also the usual set of cleanups and bug
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=SdJJ
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull Ext4 updates from Theodore Ts'o:
"The major new feature added in this update is Darrick J Wong's
metadata checksum feature, which adds crc32 checksums to ext4's
metadata fields.
There is also the usual set of cleanups and bug fixes."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (44 commits)
ext4: hole-punch use truncate_pagecache_range
jbd2: use kmem_cache_zalloc wrapper instead of flag
ext4: remove mb_groups before tearing down the buddy_cache
ext4: add ext4_mb_unload_buddy in the error path
ext4: don't trash state flags in EXT4_IOC_SETFLAGS
ext4: let getattr report the right blocks in delalloc+bigalloc
ext4: add missing save_error_info() to ext4_error()
ext4: add debugging trigger for ext4_error()
ext4: protect group inode free counting with group lock
ext4: use consistent ssize_t type in ext4_file_write()
ext4: fix format flag in ext4_ext_binsearch_idx()
ext4: cleanup in ext4_discard_allocated_blocks()
ext4: return ENOMEM when mounts fail due to lack of memory
ext4: remove redundundant "(char *) bh->b_data" casts
ext4: disallow hard-linked directory in ext4_lookup
ext4: fix potential integer overflow in alloc_flex_gd()
ext4: remove needs_recovery in ext4_mb_init()
ext4: force ro mount if ext4_setup_super() fails
ext4: fix potential NULL dereference in ext4_free_inodes_counts()
ext4/jbd2: add metadata checksumming to the list of supported features
...
Does block_sigmask() + tracehook_signal_handler(); called when
sigframe has been successfully built. All architectures converted
to it; block_sigmask() itself is gone now (merged into this one).
I'm still not too happy with the signature, but that's a separate
story (IMO we need a structure that would contain signal number +
siginfo + k_sigaction, so that get_signal_to_deliver() would fill one,
signal_delivered(), handle_signal() and probably setup...frame() -
take one).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Only 3 out of 63 do not. Renamed the current variant to __set_current_blocked(),
added set_current_blocked() that will exclude unblockable signals, switched
open-coded instances to it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
replace boilerplate "should we use ->saved_sigmask or ->blocked?"
with calls of obvious inlined helper...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
first fruits of ..._restore_sigmask() helpers: now we can take
boilerplate "signal didn't have a handler, clear RESTORE_SIGMASK
and restore the blocked mask from ->saved_mask" into a common
helper. Open-coded instances switched...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Everyone either defines it in arch thread_info.h or has TIF_RESTORE_SIGMASK
and picks default set_restore_sigmask() in linux/thread_info.h. Kill the
ifdefs, slap #error in linux/thread_info.h to catch breakage when new ones
get merged.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
NFS optimizes away d_revalidates for last component of open. This means that
open itself can find the dentry stale.
This patch allows the filesystem to return EOPENSTALE and the VFS will retry the
lookup on just the last component if possible.
If the lookup was done using RCU mode, including the last component, then this
is not possible since the parent dentry is lost. In this case fall back to
non-RCU lookup. Currently this is not used since NFS will always leave RCU
mode.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Btrfs has to make sure we have space to allocate new blocks in order to modify
the inode, so updating time can fail. We've gotten around this by having our
own file_update_time but this is kind of a pain, and Christoph has indicated he
would like to make xfs do something different with atime updates. So introduce
->update_time, where we will deal with i_version an a/m/c time updates and
indicate which changes need to be made. The normal version just does what it
has always done, updates the time and marks the inode dirty, and then
filesystems can choose to do something different.
I've gone through all of the users of file_update_time and made them check for
errors with the exception of the fault code since it's complicated and I wasn't
quite sure what to do there, also Jan is going to be pushing the file time
updates into page_mkwrite for those who have it so that should satisfy btrfs and
make it not a big deal to check the file_update_time() return code in the
generic fault path. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Version string 20120518.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove the unused argument of acpi_os_wait_events_complete.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Adds support for the PCC keyword for the Register() resource
descriptor macro.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Version 20120420.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change adds support to allow multiple notify handlers on
Device, ThermalZone, and Processor objects. Also re-worked
and restructured the entire notify support code for handler
installation, handler removal, notify event queuing, and notify
dispatch to handler.
Extends and updates original commit 3f0be67("ACPI / ACPICA: Multiple
system notify handlers per device") by Rafael Wysocki.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull the rest of the nfsd commits from Bruce Fields:
"... and then I cherry-picked the remainder of the patches from the
head of my previous branch"
This is the rest of the original nfsd branch, rebased without the
delegation stuff that I thought really needed to be redone.
I don't like rebasing things like this in general, but in this situation
this was the lesser of two evils.
* 'for-3.5' of git://linux-nfs.org/~bfields/linux: (50 commits)
nfsd4: fix, consolidate client_has_state
nfsd4: don't remove rebooted client record until confirmation
nfsd4: remove some dprintk's and a comment
nfsd4: return "real" sequence id in confirmed case
nfsd4: fix exchange_id to return confirm flag
nfsd4: clarify that renewing expired client is a bug
nfsd4: simpler ordering of setclientid_confirm checks
nfsd4: setclientid: remove pointless assignment
nfsd4: fix error return in non-matching-creds case
nfsd4: fix setclientid_confirm same_cred check
nfsd4: merge 3 setclientid cases to 2
nfsd4: pull out common code from setclientid cases
nfsd4: merge last two setclientid cases
nfsd4: setclientid/confirm comment cleanup
nfsd4: setclientid remove unnecessary terms from a logical expression
nfsd4: move rq_flavor into svc_cred
nfsd4: stricter cred comparison for setclientid/exchange_id
nfsd4: move principal name into svc_cred
nfsd4: allow removing clients not holding state
nfsd4: rearrange exchange_id logic to simplify
...
Start explicitly keeping track of the state of a ceph connection's
socket, separate from the state of the connection itself. Create
placeholder functions to encapsulate the state transitions.
--------
| NEW* | transient initial state
--------
| con_sock_state_init()
v
----------
| CLOSED | initialized, but no socket (and no
---------- TCP connection)
^ \
| \ con_sock_state_connecting()
| ----------------------
| \
+ con_sock_state_closed() \
|\ \
| \ \
| ----------- \
| | CLOSING | socket event; \
| ----------- await close \
| ^ |
| | |
| + con_sock_state_closing() |
| / \ |
| / --------------- |
| / \ v
| / --------------
| / -----------------| CONNECTING | socket created, TCP
| | / -------------- connect initiated
| | | con_sock_state_connected()
| | v
-------------
| CONNECTED | TCP connection established
-------------
Make the socket state an atomic variable, reinforcing that it's a
distinct transtion with no possible "intermediate/both" states.
This is almost certainly overkill at this point, though the
transitions into CONNECTED and CLOSING state do get called via
socket callback (the rest of the transitions occur with the
connection mutex held). We can back out the atomicity later.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil<sage@inktank.com>
A ceph_connection holds a mixture of connection state (as in "state
machine" state) and connection flags in a single "state" field. To
make the distinction more clear, define a new "flags" field and use
it rather than the "state" field to hold Boolean flag values.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil<sage@inktank.com>
A ceph client has a pointer to a ceph messenger structure in it.
There is always exactly one ceph messenger for a ceph client, so
there is no need to allocate it separate from the ceph client
structure.
Switch the ceph_client structure to embed its ceph_messenger
structure.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Yehuda Sadeh <yehuda@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
No code sets a bad_proto method in its ceph connection operations
vector, so just get rid of it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Yehuda Sadeh <yehuda@inktank.com>
The ceph connection state "DEAD" is never set and is therefore not
needed. Eliminate it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Yehuda Sadeh <yehuda@inktank.com>
We need the latest dma-buf code from Dave Airlie so that we can pimp
the backing storage handling code in drm/i915 with Chris Wilson's
unbound tracking and stolen mem backed gem object code.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The node field is always page_to_nid(c->page). So its rather easy to
replace. Note that there maybe slightly more overhead in various hot paths
due to the need to shift the bits from page->flags. However, that is mostly
compensated for by a smaller footprint of the kmem_cache_cpu structure (this
patch reduces that to 3 words per cache) which allows better caching.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Pull second pile of signal handling patches from Al Viro:
"This one is just task_work_add() series + remaining prereqs for it.
There probably will be another pull request from that tree this
cycle - at least for helpers, to get them out of the way for per-arch
fixes remaining in the tree."
Fix trivial conflict in kernel/irq/manage.c: the merge of Andrew's pile
had brought in commit 97fd75b7b8 ("kernel/irq/manage.c: use the
pr_foo() infrastructure to prefix printks") which changed one of the
pr_err() calls that this merge moves around.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
keys: kill task_struct->replacement_session_keyring
keys: kill the dummy key_replace_session_keyring()
keys: change keyctl_session_to_parent() to use task_work_add()
genirq: reimplement exit_irq_thread() hook via task_work_add()
task_work_add: generic process-context callbacks
avr32: missed _TIF_NOTIFY_RESUME on one of do_notify_resume callers
parisc: need to check NOTIFY_RESUME when exiting from syscall
move key_repace_session_keyring() into tracehook_notify_resume()
TIF_NOTIFY_RESUME is defined on all targets now
Pull nfsd update from Bruce Fields.
* 'for-3.5-take-2' of git://linux-nfs.org/~bfields/linux: (23 commits)
nfsd: trivial: use SEEK_SET instead of 0 in vfs_llseek
SUNRPC: split upcall function to extract reusable parts
nfsd: allocate id-to-name and name-to-id caches in per-net operations.
nfsd: make name-to-id cache allocated per network namespace context
nfsd: make id-to-name cache allocated per network namespace context
nfsd: pass network context to idmap init/exit functions
nfsd: allocate export and expkey caches in per-net operations.
nfsd: make expkey cache allocated per network namespace context
nfsd: make export cache allocated per network namespace context
nfsd: pass pointer to export cache down to stack wherever possible.
nfsd: pass network context to export caches init/shutdown routines
Lockd: pass network namespace to creation and destruction routines
NFSd: remove hard-coded dereferences to name-to-id and id-to-name caches
nfsd: pass pointer to expkey cache down to stack wherever possible.
nfsd: use hash table from cache detail in nfsd export seq ops
nfsd: pass svc_export_cache pointer as private data to "exports" seq file ops
nfsd: use exp_put() for svc_export_cache put
nfsd: use cache detail pointer from svc_export structure on cache put
nfsd: add link to owner cache detail to svc_export structure
nfsd: use passed cache_detail pointer expkey_parse()
...
Merge misc patches from Andrew Morton:
- the "misc" tree - stuff from all over the map
- checkpatch updates
- fatfs
- kmod changes
- procfs
- cpumask
- UML
- kexec
- mqueue
- rapidio
- pidns
- some checkpoint-restore feature work. Reluctantly. Most of it
delayed a release. I'm still rather worried that we don't have a
clear roadmap to completion for this work.
* emailed from Andrew Morton <akpm@linux-foundation.org>: (78 patches)
kconfig: update compression algorithm info
c/r: prctl: add ability to set new mm_struct::exe_file
c/r: prctl: extend PR_SET_MM to set up more mm_struct entries
c/r: procfs: add arg_start/end, env_start/end and exit_code members to /proc/$pid/stat
syscalls, x86: add __NR_kcmp syscall
fs, proc: introduce /proc/<pid>/task/<tid>/children entry
sysctl: make kernel.ns_last_pid control dependent on CHECKPOINT_RESTORE
aio/vfs: cleanup of rw_copy_check_uvector() and compat_rw_copy_check_uvector()
eventfd: change int to __u64 in eventfd_signal()
fs/nls: add Apple NLS
pidns: make killed children autoreap
pidns: use task_active_pid_ns in do_notify_parent
rapidio/tsi721: add DMA engine support
rapidio: add DMA engine support for RIO data transfers
ipc/mqueue: add rbtree node caching support
tools/selftests: add mq_perf_tests
ipc/mqueue: strengthen checks on mqueue creation
ipc/mqueue: correct mq_attr_ok test
ipc/mqueue: improve performance of send/recv
selftests: add mq_open_tests
...
When we do restore we would like to have a way to setup a former
mm_struct::exe_file so that /proc/pid/exe would point to the original
executable file a process had at checkpoint time.
For this the PR_SET_MM_EXE_FILE code is introduced. This option takes a
file descriptor which will be set as a source for new /proc/$pid/exe
symlink.
Note it allows to change /proc/$pid/exe if there are no VM_EXECUTABLE
vmas present for current process, simply because this feature is a special
to C/R and mm::num_exe_file_vmas become meaningless after that.
To minimize the amount of transition the /proc/pid/exe symlink might have,
this feature is implemented in one-shot manner. Thus once changed the
symlink can't be changed again. This should help sysadmins to monitor the
symlinks over all process running in a system.
In particular one could make a snapshot of processes and ring alarm if
there unexpected changes of /proc/pid/exe's in a system.
Note -- this feature is available iif CONFIG_CHECKPOINT_RESTORE is set and
the caller must have CAP_SYS_RESOURCE capability granted, otherwise the
request to change symlink will be rejected.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During checkpoint we dump whole process memory to a file and the dump
includes process stack memory. But among stack data itself, the stack
carries additional parameters such as command line arguments, environment
data and auxiliary vector.
So when we do restore procedure and once we've restored stack data itself
we need to setup mm_struct::arg_start/end, env_start/end, so restored
process would be able to find command line arguments and environment data
it had at checkpoint time. The same applies to auxiliary vector.
For this reason additional PR_SET_MM_(ARG_START | ARG_END | ENV_START |
ENV_END | AUXV) codes are introduced.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Vagin <avagin@openvz.org>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While doing the checkpoint-restore in the user space one need to determine
whether various kernel objects (like mm_struct-s of file_struct-s) are
shared between tasks and restore this state.
The 2nd step can be solved by using appropriate CLONE_ flags and the
unshare syscall, while there's currently no ways for solving the 1st one.
One of the ways for checking whether two tasks share e.g. mm_struct is to
provide some mm_struct ID of a task to its proc file, but showing such
info considered to be not that good for security reasons.
Thus after some debates we end up in conclusion that using that named
'comparison' syscall might be the best candidate. So here is it --
__NR_kcmp.
It takes up to 5 arguments - the pids of the two tasks (which
characteristics should be compared), the comparison type and (in case of
comparison of files) two file descriptors.
Lookups for pids are done in the caller's PID namespace only.
At moment only x86 is supported and tested.
[akpm@linux-foundation.org: fix up selftests, warnings]
[akpm@linux-foundation.org: include errno.h]
[akpm@linux-foundation.org: tweak comment text]
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Andrey Vagin <avagin@openvz.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Valdis.Kletnieks@vt.edu
Cc: Michal Marek <mmarek@suse.cz>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A cleanup of rw_copy_check_uvector and compat_rw_copy_check_uvector after
changes made to support CMA in an earlier patch.
Rather than having an additional check_access parameter to these
functions, the first paramater type is overloaded to allow the caller to
specify CHECK_IOVEC_ONLY which means check that the contents of the iovec
are valid, but do not check the memory that they point to. This is used
by process_vm_readv/writev where we need to validate that a iovec passed
to the syscall is valid but do not want to check the memory that it points
to at this point because it refers to an address space in another process.
Signed-off-by: Chris Yeoh <yeohc@au1.ibm.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
eventfd_ctx->count is an __u64 counter which is allowed to reach
ULLONG_MAX. eventfd_write() adds a __u64 value to "count", but the kernel
side eventfd_signal() only adds an int value to it. Make them consistent.
[akpm@linux-foundation.org: update interface documentation]
Signed-off-by: Sha Zhengju <handai.szj@taobao.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds DMA Engine framework support into RapidIO subsystem.
Uses DMA Engine DMA_SLAVE interface to generate data transfers to/from
remote RapidIO target devices.
Introduces RapidIO-specific wrapper for prep_slave_sg() interface with an
extra parameter to pass target specific information.
Uses scatterlist to describe local data buffer. Address flat data buffer
on a remote side.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b231cca438 ("message queues: increase range limits") changed
mqueue default value when attr parameter is specified NULL from hard
coded value to fs.mqueue.{msg,msgsize}_max sysctl value.
This made large side effect. When user need to use two mqueue
applications 1) using !NULL attr parameter and it require big message
size and 2) using NULL attr parameter and only need small size message,
app (1) require to raise fs.mqueue.msgsize_max and app (2) consume large
memory size even though it doesn't need.
Doug Ledford propsed to switch back it to static hard coded value.
However it also has a compatibility problem. Some applications might
started depend on the default value is tunable.
The solution is to separate default value from maximum value.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Acked-by: Joe Korty <joe.korty@ccur.com>
Cc: Amerigo Wang <amwang@redhat.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mqueue limitation is slightly naieve parameter likes other ipcs because
unprivileged user can consume kernel memory by using ipcs.
Thus, too aggressive raise bring us security issue. Example, current
setting allow evil unprivileged user use 256GB (= 256 * 1024 * 1024*1024)
and it's enough large to system will belome unresponsive. Don't do that.
Instead, every admin should adjust the knobs for their own systems.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Acked-by: Joe Korty <joe.korty@ccur.com>
Cc: Amerigo Wang <amwang@redhat.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b231cca438 ("message queues: increase range limits") changed the
maximum size of a message in a message queue from INT_MAX to 8192*128.
Unfortunately, we had customers that relied on a size much larger than
8192*128 on their production systems. After reviewing POSIX, we found
that it is silent on the maximum message size. We did find a couple other
areas in which it was not silent. Fix up the mqueue maximums so that the
customer's system can continue to work, and document both the POSIX and
real world requirements in ipc_namespace.h so that we don't have this
issue crop back up.
Also, commit 9cf18e1dd7 ("ipc: HARD_MSGMAX should be higher not lower
on 64bit") fiddled with HARD_MSGMAX without realizing that the number was
intentionally in place to limit the msg queue depth to one that was small
enough to kmalloc an array of pointers (hence why we divided 128k by
sizeof(long)). If we wish to meet POSIX requirements, we have no choice
but to change our allocation to a vmalloc instead (at least for the large
queue size case). With that, it's possible to increase our allowed
maximum to the POSIX requirements (or more if we choose).
[sfr@canb.auug.org.au: using vmalloc requires including vmalloc.h]
Signed-off-by: Doug Ledford <dledford@redhat.com>
Cc: Serge E. Hallyn <serue@us.ibm.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: Joe Korty <joe.korty@ccur.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b231cca438 ("message queues: increase range limits") changed
how we create a queue that does not include an attr struct passed to
open so that it creates the queue with whatever the maximum values are.
However, if the admin has set the maximums to allow flexibility in
creating a queue (aka, both a large size and large queue are allowed,
but combined they create a queue too large for the RLIMIT_MSGQUEUE of
the user), then attempts to create a queue without an attr struct will
fail. Switch back to using acceptable defaults regardless of what the
maximums are.
Note: so far, we only know of a few applications that rely on this
behavior (specifically, set the maximums in /proc, then run the
application which calls mq_open() without passing in an attr struct, and
the application expects the newly created message queue to have the
maximum sizes that were set in /proc used on the mq_open() call, and all
of those applications that we know of are actually part of regression
test suites that were coded to do something like this:
for size in 4096 65536 $((1024 * 1024)) $((16 * 1024 * 1024)); do
echo $size > /proc/sys/fs/mqueue/msgsize_max
mq_open || echo "Error opening mq with size $size"
done
These test suites that depend on any behavior like this are broken. The
concept that programs should rely upon the system wide maximum in order
to get their desired results instead of simply using a attr struct to
specify what they want is fundamentally unfriendly programming practice
for any multi-tasking OS.
Fixing this will break those few apps that we know of (and those app
authors recognize the brokenness of their code and the need to fix it).
However, the following patch "mqueue: separate mqueue default value"
allows a workaround in the form of new knobs for the default msg queue
creation parameters for any software out there that we don't already
know about that might rely on this behavior at the moment.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Cc: Serge E. Hallyn <serue@us.ibm.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: Joe Korty <joe.korty@ccur.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit b231cca438 ("message queues: increase range limits") on
Oct 18, 2008, calls to mq_open() that did not pass in an attribute
struct and expected to get default values for the size of the queue and
the max message size now get the system wide maximums instead of
hardwired defaults like they used to get.
This was uncovered when one of the earlier patches in this patch set
increased the default system wide maximums at the same time it increased
the hard ceiling on the system wide maximums (a customer specifically
needed the hard ceiling brought back up, the new ceiling that commit
b231cca438 introduced was too low for their production systems). By
increasing the default maximums and not realising they were tied to any
attempt to create a message queue without an attribute struct, I had
inadvertently made it such that all message queue creation attempts
without an attribute struct were failing because the new default
maximums would create a queue that exceeded the default rlimit for
message queue bytes.
As a result, the system wide defaults were brought back down to their
previous levels, and the system wide ceilings on the maximums were
raised to meet the customer's needs. However, the fact that the no
attribute struct behavior of mq_open() could be broken by changing the
system wide maximums for message queues was seen as fundamentally broken
itself. So we hardwired the no attribute case back like it used to be.
But, then we realized that on the very off chance that some piece of
software in the wild depended on that behavior, we could work around
that issue by adding two new knobs to /proc that allowed setting the
defaults for message queues created without an attr struct separately
from the system wide maximums.
What is not an option IMO is to leave the current behavior in place. No
piece of software should ever rely on setting the system wide maximums
in order to get a desired message queue. Such a reliance would be so
fundamentally multitasking OS unfriendly as to not really be tolerable.
Fortunately, we don't know of any software in the wild that uses this
except for a regression test program that caught the issue in the first
place. If there is though, we have made accommodations with the two new
/proc knobs (and that's all the accommodations such fundamentally broken
software can be allowed)..
This patch:
The various defines for minimums and maximums of the sysctl controllable
mqueue values are scattered amongst different files and named
inconsistently. Move them all into ipc_namespace.h and make them have
consistent names. Additionally, make the number of queues per namespace
also have a minimum and maximum and use the same sysctl function as the
other two settable variables.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: Joe Korty <joe.korty@ccur.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add userspace definitions, guard all relevant kernel structures. While at
it document stuff and remove now useless userspace hint.
It is easy to add the relevant system call to respective libc's, but it
seems pointless to have to duplicate the data structures.
This is based on the kexec-tools headers, with the exception of just using
int on return (succes or failure) and using size_t instead of 'unsigned
long int' for the number of segments argument of kexec_load().
Signed-off-by: maximilian attems <max@stro.at>
Cc: Simon Horman <horms@verge.net.au>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Haren Myneni <hbabu@us.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many architectures clear tasks' mm_cpumask like this:
read_lock(&tasklist_lock);
for_each_process(p) {
if (p->mm)
cpumask_clear_cpu(cpu, mm_cpumask(p->mm));
}
read_unlock(&tasklist_lock);
Depending on the context, the code above may have several problems,
such as:
1. Working with task->mm w/o getting mm or grabing the task lock is
dangerous as ->mm might disappear (exit_mm() assigns NULL under
task_lock(), so tasklist lock is not enough).
2. Checking for process->mm is not enough because process' main
thread may exit or detach its mm via use_mm(), but other threads
may still have a valid mm.
This patch implements a small helper function that does things
correctly, i.e.:
1. We take the task's lock while whe handle its mm (we can't use
get_task_mm()/mmput() pair as mmput() might sleep);
2. To catch exited main thread case, we use find_lock_task_mm(),
which walks up all threads and returns an appropriate task
(with task lock held).
Also, Per Peter Zijlstra's idea, now we don't grab tasklist_lock in
the new helper, instead we take the rcu read lock. We can do this
because the function is called after the cpu is taken down and marked
offline, so no new tasks will get this cpu set in their mm mask.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 8f92054e7c ("CRED: Fix __task_cred()'s lockdep check and banner
comment"):
add the following validation condition:
task->exit_state >= 0
to permit the access if the target task is dead and therefore
unable to change its own credentials.
OK, but afaics currently this can only help wait_task_zombie() which calls
__task_cred() without rcu lock.
Remove this validation and change wait_task_zombie() to use task_uid()
instead. This means we do rcu_read_lock() only to shut up the lockdep,
but we already do the same in, say, wait_task_stopped().
task_is_dead() should die, task->exit_state != 0 means that this task has
passed exit_notify(), only do_wait-like code paths should use this.
Unfortunately, we can't kill task_is_dead() right now, it has already
acquired buggy users in drivers/staging. The fix already exists.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we move call_usermodehelper_fns() to kmod.c file and EXPORT_SYMBOL it
we can avoid exporting all it's helper functions:
call_usermodehelper_setup
call_usermodehelper_setfns
call_usermodehelper_exec
And make all of them static to kmod.c
Since the optimizer will see all these as a single call site it will
inline them inside call_usermodehelper_fns(). So we loose the call to
_fns but gain 3 calls to the helpers. (Not that it matters)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
call_usermodehelper_freeinfo() is not used outside of kmod.c. So unexport
it, and make it static to kmod.c
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is patchset makes fatfs stop using the VFS '->write_super()' method
for writing out the FSINFO block.
The final goal is to get rid of the 'sync_supers()' kernel thread. This
kernel thread wakes up every 5 seconds (by default) and calls
'->write_super()' for all mounted file-systems. And the bad thing is that
this is done even if all the superblocks are clean. Moreover, some
file-systems do not even need this end they do not register the
'->write_super()' method at all (e.g., btrfs).
So 'sync_supers()' most often just generates useless wake-ups and wastes
power. I am trying to make all file-systems independent of
'->write_super()' and plan to remove 'sync_supers()' and '->write_super'
completely once there are no more users.
The '->write_supers()' method is mostly used by baroque file-systems like
hfs, udf, etc. Modern file-systems like btrfs and xfs do not use it.
This justifies removing this stuff from VFS completely and make every FS
self-manage own superblock.
Tested with xfstests.
This patch:
Preparation for further changes. It introduces a special inode
('fsinfo_inode') in FAT file-system which we'll later use for managing the
FSINFO block. Note, this there is already one special inode ('fat_inode')
which is used for managing the FAT tables.
Introduce new 'MSDOS_FSINFO_INO' constant for this special inode. It is
safe to do because FAT file-system does not store inode numbers on the
media but generates them run-time.
I've also cleaned up the comment to existing 'MSDOS_ROOT_INO' constant,
while on it.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previous code was using optimizations which were developed to work well
even on narrow-word CPUs (by today's standards). But Linux runs only on
32-bit and wider CPUs. We can use that.
First: using 32x32->64 multiply and trivial 32-bit shift, we can correctly
divide by 10 much larger numbers, and thus we can print groups of 9 digits
instead of groups of 5 digits.
Next: there are two algorithms to print larger numbers. One is generic:
divide by 1000000000 and repeatedly print groups of (up to) 9 digits.
It's conceptually simple, but requires an (unsigned long long) /
1000000000 division.
Second algorithm splits 64-bit unsigned long long into 16-bit chunks,
manipulates them cleverly and generates groups of 4 decimal digits. It so
happens that it does NOT require long long division.
If long is > 32 bits, division of 64-bit values is relatively easy, and we
will use the first algorithm. If long long is > 64 bits (strange
architecture with VERY large long long), second algorithm can't be used,
and we again use the first one.
Else (if long is 32 bits and long long is 64 bits) we use second one.
And third: there is a simple optimization which takes fast path not only
for zero as was done before, but for all one-digit numbers.
In all tested cases new code is faster than old one, in many cases by 30%,
in few cases by more than 50% (for example, on x86-32, conversion of
12345678). Code growth is ~0 in 32-bit case and ~130 bytes in 64-bit
case.
This patch is based upon an original from Michal Nazarewicz.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Douglas W Jones <jones@cs.uiowa.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ULONG_MAX is often used to check for integer overflow when calculating
allocation size. While ULONG_MAX happens to work on most systems, there
is no guarantee that `size_t' must be the same size as `long'.
This patch introduces SIZE_MAX, the maximum value of `size_t', to improve
portability and readability for allocation size validation.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Alex Elder <elder@dreamhost.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the rq_flavor into struct svc_cred, and use it in setclientid and
exchange_id comparisons as well.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Instead of keeping the principal name associated with a request in a
structure that's private to auth_gss and using an accessor function,
move it to svc_cred.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This new routine is responsible for service registration in a specified
network context.
The idea is to separate service creation from per-net operations.
Note also: since registering service with svc_bind() can fail, the
service will be destroyed and during destruction it will try to
unregister itself from rpcbind. In this case unregistration has to be
skipped.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Add a Kconfig menu (POWER_AVS) and rename the Kconfig options
for the OMAP SmartReflex implementation:
CONFIG_OMAP_SMARTREFLEX renames to CONFIG_POWER_AVS_OMAP
CONFIG_OMAP_SMARTREFLEX_CLASS3 renames to CONFIG_POWER_AVS_OMAP_CLASS3
This change makes the SmartReflex implementation ready for the move
to drivers/.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The SmartReflex driver incorrectly treats some per-OPP data as data
common to all OPPs (e.g., ERRMINLIMIT). Move this data into a per-OPP
data structure.
Furthermore, in order to make the SmartReflex implementation ready for
the move to drivers/, remove the dependency from the SR driver code
to the voltage layer by querying the data tables only from the SR device
init code.
Based on Paul's original code for the SmartReflex driver conversion.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Now that omap_test_timeout is only accessible from mach-omap2/,
introduce a similar function for SR.
This change makes the SmartReflex implementation ready for the move
to drivers/.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Associate a name with each SmartReflex instance from the hwmod data,
rather than attempting to reuse the name of a voltage domain. The name
from hwmod better reflects the smartreflex integration in the system.
Also have the name passed to the drivers using pdata, which helps to remove
any dependencies on SoC-specific structures.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Convert SmartReflex "class" functions to take a struct omap_sr *, rather than
a struct voltagedomain *. SmartReflex code should be driver code and not
tightly coupled to OMAP subarchitecture-specific structures.
Based on Paul's original code for the SmartReflex driver conversion.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Move the smartreflex header file
(arch/arm/mach-omap2/smartreflex.h) in a new header file
include/linux/power/smartreflex.h.
This change makes the SmartReflex implementation ready for the move
to drivers/.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In SRIOV mode, the number of EQs used when computing the total ICM size
was incorrect.
To fix this, we do the following:
1. We add a new structure to mlx4_dev, mlx4_phys_caps, to contain physical HCA
capabilities. The PPF uses the phys capabilities when it computes things
like ICM size.
The dev_caps structure will then contain the paravirtualized values, making
bookkeeping much easier in SRIOV mode. We add a structure rather than a
single parameter because there will be other fields in the phys_caps.
The first field we add to the mlx4_phys_caps structure is num_phys_eqs.
2. In INIT_HCA, when running in SRIOV mode, the "log_num_eqs" parameter
passed to the FW is the number of EQs per VF/PF; each function (PF or VF)
has this number of EQs available.
However, the total number of EQs which must be allowed for in the ICM is
(1 << log_num_eqs) * (#VFs + #PFs). Rather than compute this quantity,
we allocate ICM space for 1024 EQs (which is the device maximum
number of EQs, and which is the value we place in the mlx4_phys_caps structure).
For INIT_HCA, however, we use the per-function number of EQs as described
above.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=B6u0
-----END PGP SIGNATURE-----
Merge tag 'for-v3.5' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"A bunch of fixes for v3.5, nothing extraordinary."
* tag 'for-v3.5' of git://git.infradead.org/battery-2.6: (27 commits)
smb347-charger: Include missing <linux/err.h>
smb347-charger: Clean up battery attributes
max17042_battery: Add support for max17047/50 chip
sbs-battery.c: Capacity attr = remaining relative capacity
isp1704_charger: Use after free on probe error
ds2781_battery: Use DS2781_PARAM_EEPROM_SIZE and DS2781_USER_EEPROM_SIZE
power_supply: Fix a typo in BATTERY_DS2781 Kconfig entry
charger-manager: Provide cm_notify_event function for in-kernel use
charger-manager: Poll battery health in normal state
smb347-charger: Convert to regmap API
smb347-charger: Move IRQ enabling to the end of probe
smb347-charger: Rename few functions to match better what they are doing
smb347-charger: Convert to use module_i2c_driver()
smb347_charger: Cleanup power supply registration code in probe
ab8500: Clean up probe routines
ab8500_fg: Harden platform data check
ab8500_btemp: Harden platform data check
ab8500_charger: Harden platform data check
MAINTAINERS: Fix 'F' entry for the power supply class
max17042_battery: Handle irq request failure case
...
Pull two small kvm fixes from Avi Kivity:
"A build fix for non-kvm archs and a transparent hugepage refcount
bugfix on hosts with 4M pages."
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Export asm-generic/kvm_para.h
KVM: MMU: fix huge page adapted on non-PAE host
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPx1M+AAoJEDeqqVYsXL0MNOMH/jSbgDAHQskBuZMCEoVUHykZ
3aKiPFJQfnF1nQqN/xxECGFc7glrKSHv1fpAG9wDk0HLHNhP+QoOBVYdDGHpzktk
eP1hB6rWE/auJz90rIrKomJoD+cVYDRHkhlbNr1DsYBuXI+BGX0aUp+uAaajoxAT
8wp4/Z5007llQQXnep2Z0AvzIWBdCeR4PBXX5YvalJ8Qz3Rj8bYeY10oDpx6nO7v
iGcyh+h0Eo+q9KEQ3PosoDnqaskq44yTY4MWeE1Kd64fQM1JYTJo0SxOGGVxHHwQ
ZLfhX+fH3jCyBP0qRzCqBvSKTuiWeMBc8POdLbLMnq6ClCgQTr41iHH7UTuXXjE=
=fZOy
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"This is primarily another round of driver updates (bnx2fc, qla2xxx,
qla4xxx) including the target mode driver for qla2xxx. We've also got
a couple of regression fixes (async scanning, broken this merge window
and a fix to a long standing break in the scsi_wait_scan module)."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (45 commits)
[SCSI] fix scsi_wait_scan
[SCSI] fix async probe regression
[SCSI] be2iscsi: fix dma free size mismatch regression
[SCSI] qla4xxx: Update driver version to 5.02.00-k17
[SCSI] qla4xxx: Capture minidump for ISP82XX on firmware failure
[SCSI] qla4xxx: Add change_queue_depth API support
[SCSI] qla4xxx: Fix clear ddb mbx command failure issue.
[SCSI] qla4xxx: Fix kernel panic during discovery logout.
[SCSI] qla4xxx: Correct early completion of pending mbox.
[SCSI] fcoe, bnx2fc, libfcoe: SW FCoE and bnx2fc use FCoE Syfs
[SCSI] libfcoe: Add fcoe_sysfs
[SCSI] bnx2fc: Allocate fcoe_ctlr with bnx2fc_interface, not as a member
[SCSI] fcoe: Allocate fcoe_ctlr with fcoe_interface, not as a member
[SCSI] Fix dm-multipath starvation when scsi host is busy
[SCSI] ufs: fix potential NULL pointer dereferencing error in ufshcd_prove.
[SCSI] qla2xxx: don't free pool that wasn't allocated
[SCSI] mptfusion: unlock on error in mpt_config()
[SCSI] tcm_qla2xxx: Add >= 24xx series fabric module for target-core
[SCSI] qla2xxx: Add LLD target-mode infrastructure for >= 24xx series
[SCSI] Revert "qla2xxx: During loopdown perform Diagnostic loopback."
...
Use the same mechanism as the block devices are using, but move the
helper functions from fs/direct-io.c into fs/inode.c to remove the
dependency on CONFIG_BLOCK.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Fred Isaman <iisaman@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking changes from David S. Miller:
1) Fix IPSEC header length calculation for transport mode in ESP. The
issue is whether to do the calculation before or after alignment.
Fix from Benjamin Poirier.
2) Fix regression in IPV6 IPSEC fragment length calculations, from Gao
Feng. This is another transport vs tunnel mode issue.
3) Handle AF_UNSPEC connect()s properly in L2TP to avoid OOPSes. Fix
from James Chapman.
4) Fix USB ASIX driver's reception of full sized VLAN packets, from
Eric Dumazet.
5) Allow drop monitor (and, more generically, all generic netlink
protocols) to be automatically loaded as a module. From Neil
Horman.
Fix up trivial conflict in Documentation/feature-removal-schedule.txt
due to new entries added next to each other at the end. As usual.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net/smsc911x: Repair broken failure paths
virtio-net: remove useless disable on freeze
netdevice: Update netif_dbg for CONFIG_DYNAMIC_DEBUG
drop_monitor: Add module alias to enable automatic module loading
genetlink: Build a generic netlink family module alias
net: add MODULE_ALIAS_NET_PF_PROTO_NAME
r6040: Do a Proper deinit at errorpath and also when driver unloads (calling r6040_remove_one)
r6040: disable pci device if the subsequent calls (after pci_enable_device) fails
skb: avoid unnecessary reallocations in __skb_cow
net: sh_eth: fix the rxdesc pointer when rx descriptor empty happens
asix: allow full size 8021Q frames to be received
rds_rdma: don't assume infiniband device is PCI
l2tp: fix oops in L2TP IP sockets for connect() AF_UNSPEC case
mac80211: fix ADDBA declined after suspend with wowlan
wlcore: fix undefined symbols when CONFIG_PM is not defined
mac80211: fix flag check for QoS NOACK frames
ath9k_hw: apply internal regulator settings on AR933x
ath9k_hw: update AR933x initvals to fix issues with high power devices
ath9k: fix a use-after-free-bug when ath_tx_setup_buffer() fails
ath9k: stop rx dma before stopping tx
...
We faced segmentation fault on perf top -G at very high sampling rate
due to a corrupted callchain. While the root cause was not revealed (I
failed to figure it out), this patch tries to protect us from the
segfault on such cases.
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Namhyung Kim <namhyung.kim@lge.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Sunjin Yang <fan4326@gmail.com>
Link: http://lkml.kernel.org/r/1338443007-24857-2-git-send-email-namhyung.kim@lge.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Recently I'm working on fanotify and found the following strange
behaviors.
I wrote a program to set fanotify_mark on "/tmp/block" and FAN_DENY
all events notified.
fanotify_mask = FAN_ALL_EVENTS | FAN_ALL_PERM_EVENTS | FAN_EVENT_ON_CHILD:
$ cd /tmp/block; cat foo
cat: foo: Operation not permitted
Operation on the file is blocked as expected.
But,
fanotify_mask = FAN_ALL_PERM_EVENTS | FAN_EVENT_ON_CHILD:
$ cd /tmp/block; cat foo
aaa
It's not blocked anymore. This is confusing behavior. Also reading
commit "fsnotify: call fsnotify_parent in perm events", it seems like
fsnotify should handle subfiles' perm events as well as the other notify
events.
With this patch, regardless of FAN_ALL_EVENTS set or not:
$ cd /tmp/block; cat foo
cat: foo: Operation not permitted
Operation on the file is now blocked properly.
FS_OPEN_PERM and FS_ACCESS_PERM are not listed on FS_EVENTS_POSS_ON_CHILD.
Due to fsnotify_inode_watches_children() check, if you only specify only
these events as fsnotify_mask, you don't get subfiles' perm events
notified.
This patch add the events to FS_EVENTS_POSS_ON_CHILD to get them notified
even if only these events are specified to fsnotify_mask.
Signed-off-by: Naohiro Aota <naota@elisp.net>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make netif_dbg use dynamic debugging whenever
CONFIG_DYNAMIC_DEBUG is enabled.
commit b558c96ffa
("dynamic_debug: make dynamic-debug supersede DEBUG ccflag")
missed updating the netif_dbg variant.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ceph updates from Sage Weil:
"There are some updates and cleanups to the CRUSH placement code, a bug
fix with incremental maps, several cleanups and fixes from Josh Durgin
in the RBD block device code, a series of cleanups and bug fixes from
Alex Elder in the messenger code, and some miscellaneous bounds
checking and gfp cleanups/fixes."
Fix up trivial conflicts in net/ceph/{messenger.c,osdmap.c} due to the
networking people preferring "unsigned int" over just "unsigned".
* git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (45 commits)
libceph: fix pg_temp updates
libceph: avoid unregistering osd request when not registered
ceph: add auth buf in prepare_write_connect()
ceph: rename prepare_connect_authorizer()
ceph: return pointer from prepare_connect_authorizer()
ceph: use info returned by get_authorizer
ceph: have get_authorizer methods return pointers
ceph: ensure auth ops are defined before use
ceph: messenger: reduce args to create_authorizer
ceph: define ceph_auth_handshake type
ceph: messenger: check return from get_authorizer
ceph: messenger: rework prepare_connect_authorizer()
ceph: messenger: check prepare_write_connect() result
ceph: don't set WRITE_PENDING too early
ceph: drop msgr argument from prepare_write_connect()
ceph: messenger: send banner in process_connect()
ceph: messenger: reset connection kvec caller
libceph: don't reset kvec in prepare_write_banner()
ceph: ignore preferred_osd field
ceph: fully initialize new layout
...
Pull i2c updates from Jean Delvare.
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Split I2C_M_NOSTART support out of I2C_FUNC_PROTOCOL_MANGLING
i2c-dev: Add support for I2C_M_RECV_LEN
Pull second set of watchdog updates from Wim Van Sebroeck:
"This changeset contains following changes:
* Add support for multiple watchdog devices. We use dynamically
allocated device id's for this.
* Add locking into the generic watchdog infrastructure.
* Add support for dynamically allocated watchdog_device structs so
that we can deal with devices that get unbound.
* convert following drivers to the generic watchdog framework:
sch5627, sch5636 and sp805_wdt.
* Add DA9052/53 PMIC watchdog support
* Fix printk format warnings for iTCO_wdt.c"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: iTCO_wdt.c: fix printk format warnings
watchdog: sp805_wdt: Add clk_{un}prepare support
watchdog: sp805_wdt: convert to watchdog core
hwmon/sch56xx: Depend on watchdog for watchdog core functions
watchdog: sch56xx-common: set correct bits in register()
Watchdog: DA9052/53 PMIC watchdog support
watchdog: sch56xx-common: Add proper ref-counting of watchdog data
watchdog: sch56xx: Remove unnecessary checks for register changes
watchdog: sch56xx: Use watchdog core
watchdog: Add support for dynamically allocated watchdog_device structs
watchdog: Add Locking support
watchdog: watchdog_dev: Rewrite wrapper code
watchdog: use dev_ functions
watchdog: create all the proper device files
watchdog: Add a flag to indicate the watchdog doesn't reboot things
watchdog: Add multiple device support
watchdog: watchdog_core.h: make functions extern
watchdog: correct the name of the watchdog_core inlude file
watchdog: Add watchdog_active() routine
watchdog: watchdog_dev: include private header to pickup global symbol prototypes
Pull block driver updates from Jens Axboe:
"Here are the driver related changes for 3.5. It contains:
- The floppy changes from Jiri. Jiri is now also marked as the
maintainer of floppy.c, I shall be publically branding his forehead
with red hot iron at the next opportune moment.
- A batch of drbd updates and fixes from the linbit crew, as well as
fixes from others.
- Two small fixes for xen-blkfront courtesy of Jan."
* 'for-3.5/drivers' of git://git.kernel.dk/linux-block: (70 commits)
floppy: take over maintainership
floppy: remove floppy-specific O_EXCL handling
floppy: convert to delayed work and single-thread wq
xen-blkfront: module exit handling adjustments
xen-blkfront: properly name all devices
drbd: grammar fix in log message
drbd: check MODULE for THIS_MODULE
drbd: Restore the request restart logic
drbd: introduce a bio_set to allocate housekeeping bios from
drbd: remove unused define
drbd: bm_page_async_io: properly initialize page->private
drbd: use the newly introduced page pool for bitmap IO
drbd: add page pool to be used for meta data IO
drbd: allow bitmap to change during writeout from resync_finished
drbd: fix race between drbdadm invalidate/verify and finishing resync
drbd: fix resend/resubmit of frozen IO
drbd: Ensure that data_size is not 0 before using data_size-1 as index
drbd: Delay/reject other state changes while establishing a connection
drbd: move put_ldev from __req_mod() to the endio callback
drbd: fix WRITE_ACKED_BY_PEER_AND_SIS to not set RQ_NET_DONE
...
Merge block/IO core bits from Jens Axboe:
"This is a bit bigger on the core side than usual, but that is purely
because we decided to hold off on parts of Tejun's submission on 3.4
to give it a bit more time to simmer. As a consequence, it's seen a
long cycle in for-next.
It contains:
- Bug fix from Dan, wrong locking type.
- Relax splice gifting restriction from Eric.
- A ton of updates from Tejun, primarily for blkcg. This improves
the code a lot, making the API nicer and cleaner, and also includes
fixes for how we handle and tie policies and re-activate on
switches. The changes also include generic bug fixes.
- A simple fix from Vivek, along with a fix for doing proper delayed
allocation of the blkcg stats."
Fix up annoying conflict just due to different merge resolution in
Documentation/feature-removal-schedule.txt
* 'for-3.5/core' of git://git.kernel.dk/linux-block: (92 commits)
blkcg: tg_stats_alloc_lock is an irq lock
vmsplice: relax alignement requirements for SPLICE_F_GIFT
blkcg: use radix tree to index blkgs from blkcg
blkcg: fix blkcg->css ref leak in __blkg_lookup_create()
block: fix elvpriv allocation failure handling
block: collapse blk_alloc_request() into get_request()
blkcg: collapse blkcg_policy_ops into blkcg_policy
blkcg: embed struct blkg_policy_data in policy specific data
blkcg: mass rename of blkcg API
blkcg: style cleanups for blk-cgroup.h
blkcg: remove blkio_group->path[]
blkcg: blkg_rwstat_read() was missing inline
blkcg: shoot down blkgs if all policies are deactivated
blkcg: drop stuff unused after per-queue policy activation update
blkcg: implement per-queue policy activation
blkcg: add request_queue->root_blkg
blkcg: make request_queue bypassing on allocation
blkcg: make sure blkg_lookup() returns %NULL if @q is bypassing
blkcg: make blkg_conf_prep() take @pol and return with queue lock held
blkcg: remove static policy ID enums
...
Not much stuff this time. The only change to the IOMMU core code is the
addition of a handle to the fault handling code. A few updates to the
AMD IOMMU driver to work around new errata. The other patches are mostly
fixes and enhancements to the existing ARM IOMMU drivers and
documentation updates.
A new IOMMU driver for the Exynos platform was also underway but got
merged via the Samsung tree and is not part of this tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=K23I
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"Not much stuff this time. The only change to the IOMMU core code is
the addition of a handle to the fault handling code. A few updates to
the AMD IOMMU driver to work around new errata. The other patches are
mostly fixes and enhancements to the existing ARM IOMMU drivers and
documentation updates.
A new IOMMU driver for the Exynos platform was also underway but got
merged via the Samsung tree and is not part of this tree."
* tag 'iommu-updates-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
Documentation: kernel-parameters.txt Add amd_iommu_dump
iommu/core: pass a user-provided token to fault handlers
iommu/tegra: gart: Fix register offset correctly
iommu: OMAP: device detach on domain destroy
iommu: tegra/gart: Add device tree support
iommu: tegra/gart: use correct gart_device
iommu/tegra: smmu: Print device name correctly
iommu/amd: Add workaround for event log erratum
iommu/amd: Check for the right TLP prefix bit
dma-debug: release free_entries_lock before saving stack trace
Since nr_cpus_allowed is used outside of sched/rt.c and wants to be
used outside of there more, move it to a more natural site.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-kr61f02y9brwzkh6x53pdptm@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Follow up on commit 556061b00 ("sched/nohz: Fix rq->cpu_load[]
calculations") since while that fixed the busy case it regressed the
mostly idle case.
Add a callback from the nohz exit to also age the rq->cpu_load[]
array. This closes the hole where either there was no nohz load
balance pass during the nohz, or there was a 'significant' amount of
idle time between the last nohz balance and the nohz exit.
So we'll update unconditionally from the tick to not insert any
accidental 0 load periods while busy, and we try and catch up from
nohz idle balance and nohz exit. Both these are still prone to missing
a jiffy, but that has always been the case.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: pjt@google.com
Cc: Venkatesh Pallipadi <venki@google.com>
Link: http://lkml.kernel.org/n/tip-kt0trz0apodbf84ucjfdbr1a@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This adds a new ioctl to enable userspace to control the size of the guest
hashed page table (HPT) and to clear it out when resetting the guest.
The KVM_PPC_ALLOCATE_HTAB ioctl is a VM ioctl and takes as its parameter
a pointer to a u32 containing the desired order of the HPT (log base 2
of the size in bytes), which is updated on successful return to the
actual order of the HPT which was allocated.
There must be no vcpus running at the time of this ioctl. To enforce
this, we now keep a count of the number of vcpus running in
kvm->arch.vcpus_running.
If the ioctl is called when a HPT has already been allocated, we don't
reallocate the HPT but just clear it out. We first clear the
kvm->arch.rma_setup_done flag, which has two effects: (a) since we hold
the kvm->lock mutex, it will prevent any vcpus from starting to run until
we're done, and (b) it means that the first vcpu to run after we're done
will re-establish the VRMA if necessary.
If userspace doesn't call this ioctl before running the first vcpu, the
kernel will allocate a default-sized HPT at that point. We do it then
rather than when creating the VM, as the code did previously, so that
userspace has a chance to do the ioctl if it wants.
When allocating the HPT, we can allocate either from the kernel page
allocator, or from the preallocated pool. If userspace is asking for
a different size from the preallocated HPTs, we first try to allocate
using the kernel page allocator. Then we try to allocate from the
preallocated pool, and then if that fails, we try allocating decreasing
sizes from the kernel page allocator, down to the minimum size allowed
(256kB). Note that the kernel page allocator limits allocations to
1 << CONFIG_FORCE_MAX_ZONEORDER pages, which by default corresponds to
16MB (on 64-bit powerpc, at least).
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix module compilation]
Signed-off-by: Alexander Graf <agraf@suse.de>
Since there are uses for I2C_M_NOSTART which are much more sensible and
standard than most of the protocol mangling functionality (the main one
being gather writes to devices where something like a register address
needs to be inserted before a block of data) create a new I2C_FUNC_NOSTART
for this feature and update all the users to use it.
Also strengthen the disrecommendation of the protocol mangling while we're
at it.
In the case of regmap-i2c we remove the requirement for mangling as
I2C_M_NOSTART is the only mangling feature which is being used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If a driver's watchdog_device struct is part of a dynamically allocated
struct (which it often will be), merely locking the module is not enough,
even with a drivers module locked, the driver can be unbound from the device,
examples:
1) The root user can unbind it through sysfd
2) The i2c bus master driver being unloaded for an i2c watchdog
I will gladly admit that these are corner cases, but we still need to handle
them correctly.
The fix for this consists of 2 parts:
1) Add ref / unref operations, so that the driver can refcount the struct
holding the watchdog_device struct and delay freeing it until any
open filehandles referring to it are closed
2) Most driver operations will do IO on the device and the driver should not
do any IO on the device after it has been unbound. Rather then letting each
driver deal with this internally, it is better to ensure at the watchdog
core level that no operations (other then unref) will get called after
the driver has called watchdog_unregister_device(). This actually is the
bulk of this patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch fixes some potential multithreading issues, despite only
allowing one process to open the /dev/watchdog device, we can still get
called multiple times at the same time, since a program could be using thread,
or could share the fd after a fork.
This causes 2 potential problems:
1) watchdog_start / open do an unlocked test_n_set / test_n_clear,
if these 2 race, the watchdog could be stopped while the active
bit indicates it is running or visa versa.
2) Most watchdog_dev drivers probably assume that only one
watchdog-op will get called at a time, this is not necessary
true atm.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Create the watchdog class and it's associated devices.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Some watchdogs merely trigger external alarms and controls. In a managed
environment this is very useful but we want drivers to be able to figure
out which is which now multiple dogs can be loaded. Thus add an ALARMONLY
feature flag.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We keep the old /dev/watchdog interface file for the first watchdog via
miscdev. This is basically a cut and paste of the relevant interface code
from the rtc driver layer tweaked for watchdog.
Revised to fix problems noted by Hans de Goede
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Some watchdog may need to check if watchdog is ACTIVE or not, for example in
their suspend/resume hooks.
This patch adds this routine and changes the core drivers to use it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
lglocks and brlocks are currently generated with some complicated macros
in lglock.h. But there's no reason to not just use common utility
functions and put all the data into a common data structure.
Since there are at least two users it makes sense to share this code in a
library. This is also easier maintainable than a macro forest.
This will also make it later possible to dynamically allocate lglocks and
also use them in modules (this would both still need some additional, but
now straightforward, code)
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Optimizing the slow paths adds a lot of complexity. If you need to
grab every lock often, you have other problems.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
pass inode + parent's inode or NULL instead of dentry + bool saying
whether we want the parent or not.
NOTE: that needs ceph fix folded in.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Generic netlink searches for -type- formatted aliases when requesting a module to
fulfill a protocol request (i.e. net-pf-16-proto-16-type-<x>, where x is a type
value). However generic netlink protocols have no well defined type numbers,
they have string names. Modify genl_ctrl_getfamily to request an alias in the
format net-pf-16-proto-16-family-<x> instead, where x is a generic string, and
add a macro that builds on the previously added MODULE_ALIAS_NET_PF_PROTO_NAME
macro to allow modules to specifify those generic strings.
Note, l2tp previously hacked together an net-pf-16-proto-16-type-l2tp alias
using the MODULE_ALIAS macro, with these updates we can convert that to use the
PROTO_NAME macro.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: James Chapman <jchapman@katalix.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MODULE_ALAIS_NET_PF macro set is missing a variant that allows for the
appending of an arbitrary string to the net-pf-<x>-proto-<y> base. while
MODULE_ALIAS_NET_PF_PROTO_NAME_TYPE allows an appending of a numerical type, we
need to be able to append a generic string to support generic netlink families
that have neither a fix numberical protocol nor type number
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull EDAC internal API changes from Mauro Carvalho Chehab:
"This changeset is the first part of a series of patches that fixes the
EDAC sybsystem. On this set, it changes the Kernel EDAC API in order
to properly represent the Intel i3/i5/i7, Xeon 3xxx/5xxx/7xxx, and
Intel E5-xxxx memory controllers.
The EDAC core used to assume that:
- the DRAM chip select pin is directly accessed by the memory
controller
- when multiple channels are used, they're all filled with the
same type of memory.
None of the above premises is true on Intel memory controllers since
2002, when RAMBUS and FB-DIMMs were introduced, and Advanced Memory
Buffer or by some similar technologies hides the direct access to the
DRAM pins.
So, the existing drivers for those chipsets had to lie to the EDAC
core, in general telling that just one channel is filled. That
produces some hard to understand error messages like:
EDAC MC0: CE row 3, channel 0, label "DIMM1": 1 Unknown error(s): memory read error on FATAL area : cpu=0 Err=0008:00c2 (ch=2), addr = 0xad1f73480 => socket=0, Channel=0(mask=2), rank=1
The location information there (row3 channel 0) is completely bogus:
it has no physical meaning, and are just some random values that the
driver uses to talk with the EDAC core. The error actually happened
at CPU socket 0, channel 0, slot 1, but this is not reported anywhere,
as the EDAC core doesn't know anything about the memory layout. So,
only advanced users that know how the EDAC driver works and that tests
their systems to see how DIMMs are mapped can actually benefit for
such error logs.
This patch series fixes the error report logic, in order to allow the
EDAC to expose the memory architecture used by them to the EDAC core.
So, as the EDAC core now understands how the memory is organized, it
can provide an useful report:
EDAC MC0: CE memory read error on DIMM1 (channel:0 slot:1 page:0x364b1b offset:0x600 grain:32 syndrome:0x0 - count:1 area:DRAM err_code:0001:0090 socket:0 channel_mask:1 rank:4)
The location of the DIMM where the error happened is reported by "MC0"
(cpu socket #0), at "channel:0 slot:1" location, and matches the
physical location of the DIMM.
There are two remaining issues not covered by this patch series:
- The EDAC sysfs API will still report bogus values. So,
userspace tools like edac-utils will still use the bogus data;
- Add a new tracepoint-based way to get the binary information
about the errors.
Those are on a second series of patches (also at -next), but will
probably miss the train for 3.5, due to the slow review process."
Fix up trivial conflict (due to spelling correction of removed code) in
drivers/edac/edac_device.c
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: (42 commits)
i7core: fix ranks information at the per-channel struct
i5000: Fix the fatal error handling
i5100_edac: Fix a warning when compiled with 32 bits
i82975x_edac: Test nr_pages earlier to save a few CPU cycles
e752x_edac: provide more info about how DIMMS/ranks are mapped
i5000_edac: Fix the logic that retrieves memory information
i5400_edac: improve debug messages to better represent the filled memory
edac: Cleanup the logs for i7core and sb edac drivers
edac: Initialize the dimm label with the known information
edac: Remove the legacy EDAC ABI
x38_edac: convert driver to use the new edac ABI
tile_edac: convert driver to use the new edac ABI
sb_edac: convert driver to use the new edac ABI
r82600_edac: convert driver to use the new edac ABI
ppc4xx_edac: convert driver to use the new edac ABI
pasemi_edac: convert driver to use the new edac ABI
mv64x60_edac: convert driver to use the new edac ABI
mpc85xx_edac: convert driver to use the new edac ABI
i82975x_edac: convert driver to use the new edac ABI
i82875p_edac: convert driver to use the new edac ABI
...
Pull MIPS updates from Ralf Baechle:
"The whole series has been sitting in -next for quite a while with no
complaints. The last change to the series was before the weekend the
removal of an SPI patch which Grant - even though previously acked by
himself - appeared to raise objections. So I removed it until the
situation is clarified. Other than that all the patches have the acks
from their respective maintainers, all MIPS and x86 defconfigs are
building fine and I'm not aware of any problems introduced by this
series.
Among the key features for this patch series is a sizable patchset for
Lantiq which among other things introduces support for Lantiq's
flagship product, the FALCON SOC. It also means that the opensource
developers behind this patchset have overtaken Lantiq's competing
inhouse development team that was working behind closed doors.
Less noteworthy the ath79 patchset which adds support for a few more
chip variants, cleanups and fixes. Finally the usual dose of tweaking
of generic code."
Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
MIPS: lantiq: remove orphaned code
MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
MIPS: lantiq: implement support for FALCON soc
MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
MTD: MIPS: lantiq: implement OF support
watchdog: MIPS: lantiq: implement OF support and minor fixes
SERIAL: MIPS: lantiq: implement OF support
GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
MIPS: pci: convert lantiq driver to OF
MIPS: lantiq: convert dma to platform driver
MIPS: lantiq: implement support for clkdev api
MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
OF: MIPS: lantiq: implement irq_domain support
OF: MIPS: lantiq: implement OF support
MIPS: lantiq: drop mips_machine support
OF: PCI: const usage needed by MIPS
MIPS: Cavium: Remove smp_reserve_lock.
MIPS: Move cache setup to setup_arch().
...
Some DS13XX devices have "trickle chargers". Its configuration register
is at different locations, the setup is the same, though. Since the
configuration is board specific, introduce a platform_data to this driver.
Tested with a DS1339 on a custom board.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently there is no generic way to get the RTC battery status within an
application. So add an ioctl to read the status bit. The idea is that
the bit is set once a low voltage is detected. It stays there until it is
reset using the RTC_VL_CLR ioctl.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using %ps in a printk format will sometimes fail silently and print the
empty string if the address passed in does not match a symbol that
kallsyms knows about. But using %pS will fall back to printing the full
address if kallsyms can't find the symbol. Make %ps act the same as %pS
by falling back to printing the address.
While we're here also make %ps print the module that a symbol comes from
so that it matches what %pS already does. Take this simple function for
example (in a module):
static void test_printk(void)
{
int test;
pr_info("with pS: %pS\n", &test);
pr_info("with ps: %ps\n", &test);
}
Before this patch:
with pS: 0xdff7df44
with ps:
After this patch:
with pS: 0xdff7df44
with ps: 0xdff7df44
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
max brightness is 127, so the range of brt_val should be from 0 to 127
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new field to led_classdev to save activattion state after activate
routine is successful. This saved state is used in deactivate routine to
do cleanup such as removing device files, and free memory allocated during
activation. Currently trigger_data not being null is used for this
purpose.
Existing triggers will need changes to use this new field.
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include the header to pickup the exported symbol prototype.
Quiets the sparse warning:
warning: symbol 'apple_bl_register' was not declared. Should it be static?
warning: symbol 'apple_bl_unregister' was not declared. Should it be static?
[akpm@linux-foundation.org: fix resulting build error]
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patchset adds early fb blank feature that a callback of lcd panel
driver is called prior to specific fb driver's one. In the case of
MIPI-DSI based video mode LCD Panel, for lcd power off, the power off
commands should be transferred to lcd panel with display and mipi-dsi
controller enabled because the commands is set to lcd panel at vsync porch
period. and in opposite case, the callback of fb driver should be called
prior to lcd panel driver's one because of same issue. Also if fb_blank
mode is changed to FB_BLANK_POWERDOWN then display controller would be
off(clock disable) but lcd panel would be still on. at this time, you
could see some issue like sparkling on lcd panel because video clock to be
delivered to ldi module of lcd panel was disabled. this issue could
occurs for all lcd panels.
The callback order is as the following:
at fb_blank function of fbmem.c
-> fb_notifier_call_chain(FB_EARLY_EVENT_BLANK)
-> lcd panel driver's early_set_power()
-> info->fbops->fb_blank()
-> spcefic fb driver's fb_blank()
-> fb_notifier_call_chain(FB_EVENT_BLANK)
-> lcd panel driver's set_power()
-> fb_notifier_call_chain(FB_R_EARLY_EVENT_BLANK) if
info->fops->fb_blank() was failed.
fb_notifier_call_chain(FB_R_EARLY_EVENT_BLANK) would be called to revert
the effects of previous FB_EARLY_EVENT_BLANK call. and note that if
early_set_power() of lcd_ops is NULL then early fb blank callback would be
ignored.
This patch:
Add early_set_power and r_early_set_power callbacks. early_set_power
callback is called prior to fb_blank() of fbmem.c and r_early_set_power
callback is called if fb_blank() was failed to revert the effects of the
early_set_power call of lcd panel driver.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add FB_EARLY_EVENT_BLANK and FB_R_EARLY_EVENT_BLANK event mode supports.
first, fb_notifier_call_chain() is called with FB_EARLY_EVENT_BLANK and
fb_blank() of specific fb driver is called and then
fb_notifier_call_chain() is called with FB_EVENT_BLANK again at
fb_blank(). and if fb_blank() was failed then fb_nitifier_call_chain()
would be called with FB_R_EARLY_EVENT_BLANK to revert the previous
effects.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We call the destroy function when a cgroup starts to be removed, such as
by a rmdir event.
However, because of our reference counters, some objects are still
inflight. Right now, we are decrementing the static_keys at destroy()
time, meaning that if we get rid of the last static_key reference, some
objects will still have charges, but the code to properly uncharge them
won't be run.
This becomes a problem specially if it is ever enabled again, because now
new charges will be added to the staled charges making keeping it pretty
much impossible.
We just need to be careful with the static branch activation: since there
is no particular preferred order of their activation, we need to make sure
that we only start using it after all call sites are active. This is
achieved by having a per-memcg flag that is only updated after
static_key_slow_inc() returns. At this time, we are sure all sites are
active.
This is made per-memcg, not global, for a reason: it also has the effect
of making socket accounting more consistent. The first memcg to be
limited will trigger static_key() activation, therefore, accounting. But
all the others will then be accounted no matter what. After this patch,
only limited memcgs will have its sockets accounted.
[akpm@linux-foundation.org: move enum sock_flag_bits into sock.h,
document enum sock_flag_bits,
convert memcg_proto_active() and memcg_proto_activated() to test_bit(),
redo tcp_update_limit() comment to 80 cols]
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Take lruvec further: pass it instead of zone to add_page_to_lru_list() and
del_page_from_lru_list(); and pagevec_lru_move_fn() pass lruvec down to
its target functions.
This cleanup eliminates a swathe of cruft in memcontrol.c, including
mem_cgroup_lru_add_list(), mem_cgroup_lru_del_list() and
mem_cgroup_lru_move_lists() - which never actually touched the lists.
In their place, mem_cgroup_page_lruvec() to decide the lruvec, previously
a side-effect of add, and mem_cgroup_update_lru_size() to maintain the
lru_size stats.
Whilst these are simplifications in their own right, the goal is to bring
the evaluation of lruvec next to the spin_locking of the lrus, in
preparation for a future patch.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Konstantin just introduced mem_cgroup_get_lruvec_size() and
get_lruvec_size(), I'm about to add mem_cgroup_update_lru_size(): but
we're dealing with the same thing, lru_size[lru]. We ought to agree on
the naming, and I do think lru_size is the more correct: so rename his
ones to get_lru_size().
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we will succeed with the allocation no matter what, there isn't a
need to use __must_check with it. It can very well be optional.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ying Han <yinghan@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When killing a res_counter which is a child of other counter, we need to
do
res_counter_uncharge(child, xxx)
res_counter_charge(parent, xxx)
This is not atomic and wastes CPU. This patch adds
res_counter_uncharge_until(). This function's uncharge propagates to
ancestors until specified res_counter.
res_counter_uncharge_until(child, parent, xxx)
Now the operation is atomic and efficient.
Signed-off-by: Frederic Weisbecker <fweisbec@redhat.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Ying Han <yinghan@google.com>
Cc: Glauber Costa <glommer@parallels.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If memory cgroup is enabled we always use lruvecs which are embedded into
struct mem_cgroup_per_zone, so we can reach lru_size counters via
container_of().
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the first stage of struct mem_cgroup_zone removal. Further
patches replace struct mem_cgroup_zone with a pointer to struct lruvec.
If CONFIG_CGROUP_MEM_RES_CTLR=n lruvec_zone() is just container_of().
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With mem_cgroup_disabled() now explicit, it becomes clear that the
zone_reclaim_stat structure actually belongs in lruvec, per-zone when
memcg is disabled but per-memcg per-zone when it's enabled.
We can delete mem_cgroup_get_reclaim_stat(), and change
update_page_reclaim_stat() to update just the one set of stats, the one
which get_scan_count() will actually use.
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch kills mem_cgroup_lru_del(), we can use
mem_cgroup_lru_del_list() instead. On 0-order isolation we already have
right lru list id.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After patch "mm: forbid lumpy-reclaim in shrink_active_list()" we can
completely remove anon/file and active/inactive lru type filters from
__isolate_lru_page(), because isolation for 0-order reclaim always
isolates pages from right lru list. And pages-isolation for lumpy
shrink_inactive_list() or memory-compaction anyway allowed to isolate
pages from all evictable lru lists.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GCC sometimes ignores "inline" directives even for small and simple functions.
This supposed to be fixed in gcc 4.7, but it was released only yesterday.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes memcg's behavior at task_move().
At task_move(), the kernel scans a task's page table and move the changes
for mapped pages from source cgroup to target cgroup. There has been a
bug at handling shared anonymous pages for a long time.
Before patch:
- The spec says 'shared anonymous pages are not moved.'
- The implementation was 'shared anonymoys pages may be moved'.
If page_mapcount <=2, shared anonymous pages's charge were moved.
After patch:
- The spec says 'all anonymous pages are moved'.
- The implementation is 'all anonymous pages are moved'.
Considering usage of memcg, this will not affect user's experience.
'shared anonymous' pages only exists between a tree of processes which
don't do exec(). Moving one of process without exec() seems not sane.
For example, libcgroup will not be affected by this change. (Anyway, no
one noticed the implementation for a long time...)
Below is a discussion log:
- current spec/implementation are complex
- Now, shared file caches are moved
- It adds unclear check as page_mapcount(). To do correct check,
we should check swap users, etc.
- No one notice this implementation behavior. So, no one get benefit
from the design.
- In general, once task is moved to a cgroup for running, it will not
be moved....
- Finally, we have control knob as memory.move_charge_at_immigrate.
Here is a patch to allow moving shared pages, completely. This makes
memcg simpler and fix current broken code.
Suggested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Glauber Costa <glommer@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Transparent huge pages can change page->flags (PG_compound_lock) without
taking Slab lock. Since THP can not break slab pages we can safely access
compound page without taking compound lock.
Specifically this patch fixes a race between compound_unlock() and slab
functions which perform page-flags updates. This can occur when
get_page()/put_page() is called on a page from slab.
[akpm@linux-foundation.org: tweak comment text, fix comment layout, fix label indenting]
Reported-by: Amey Bhide <abhide@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Acked-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When holding the mmap_sem for reading, pmd_offset_map_lock should only
run on a pmd_t that has been read atomically from the pmdp pointer,
otherwise we may read only half of it leading to this crash.
PID: 11679 TASK: f06e8000 CPU: 3 COMMAND: "do_race_2_panic"
#0 [f06a9dd8] crash_kexec at c049b5ec
#1 [f06a9e2c] oops_end at c083d1c2
#2 [f06a9e40] no_context at c0433ded
#3 [f06a9e64] bad_area_nosemaphore at c043401a
#4 [f06a9e6c] __do_page_fault at c0434493
#5 [f06a9eec] do_page_fault at c083eb45
#6 [f06a9f04] error_code (via page_fault) at c083c5d5
EAX: 01fb470c EBX: fff35000 ECX: 00000003 EDX: 00000100 EBP:
00000000
DS: 007b ESI: 9e201000 ES: 007b EDI: 01fb4700 GS: 00e0
CS: 0060 EIP: c083bc14 ERR: ffffffff EFLAGS: 00010246
#7 [f06a9f38] _spin_lock at c083bc14
#8 [f06a9f44] sys_mincore at c0507b7d
#9 [f06a9fb0] system_call at c083becd
start len
EAX: ffffffda EBX: 9e200000 ECX: 00001000 EDX: 6228537f
DS: 007b ESI: 00000000 ES: 007b EDI: 003d0f00
SS: 007b ESP: 62285354 EBP: 62285388 GS: 0033
CS: 0073 EIP: 00291416 ERR: 000000da EFLAGS: 00000286
This should be a longstanding bug affecting x86 32bit PAE without THP.
Only archs with 64bit large pmd_t and 32bit unsigned long should be
affected.
With THP enabled the barrier() in pmd_none_or_trans_huge_or_clear_bad()
would partly hide the bug when the pmd transition from none to stable,
by forcing a re-read of the *pmd in pmd_offset_map_lock, but when THP is
enabled a new set of problem arises by the fact could then transition
freely in any of the none, pmd_trans_huge or pmd_trans_stable states.
So making the barrier in pmd_none_or_trans_huge_or_clear_bad()
unconditional isn't good idea and it would be a flakey solution.
This should be fully fixed by introducing a pmd_read_atomic that reads
the pmd in order with THP disabled, or by reading the pmd atomically
with cmpxchg8b with THP enabled.
Luckily this new race condition only triggers in the places that must
already be covered by pmd_none_or_trans_huge_or_clear_bad() so the fix
is localized there but this bug is not related to THP.
NOTE: this can trigger on x86 32bit systems with PAE enabled with more
than 4G of ram, otherwise the high part of the pmd will never risk to be
truncated because it would be zero at all times, in turn so hiding the
SMP race.
This bug was discovered and fully debugged by Ulrich, quote:
----
[..]
pmd_none_or_trans_huge_or_clear_bad() loads the content of edx and
eax.
496 static inline int pmd_none_or_trans_huge_or_clear_bad(pmd_t
*pmd)
497 {
498 /* depend on compiler for an atomic pmd read */
499 pmd_t pmdval = *pmd;
// edi = pmd pointer
0xc0507a74 <sys_mincore+548>: mov 0x8(%esp),%edi
...
// edx = PTE page table high address
0xc0507a84 <sys_mincore+564>: mov 0x4(%edi),%edx
...
// eax = PTE page table low address
0xc0507a8e <sys_mincore+574>: mov (%edi),%eax
[..]
Please note that the PMD is not read atomically. These are two "mov"
instructions where the high order bits of the PMD entry are fetched
first. Hence, the above machine code is prone to the following race.
- The PMD entry {high|low} is 0x0000000000000000.
The "mov" at 0xc0507a84 loads 0x00000000 into edx.
- A page fault (on another CPU) sneaks in between the two "mov"
instructions and instantiates the PMD.
- The PMD entry {high|low} is now 0x00000003fda38067.
The "mov" at 0xc0507a8e loads 0xfda38067 into eax.
----
Reported-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The oom_score_adj scale ranges from -1000 to 1000 and represents the
proportion of memory available to the process at allocation time. This
means an oom_score_adj value of 300, for example, will bias a process as
though it was using an extra 30.0% of available memory and a value of
-350 will discount 35.0% of available memory from its usage.
The oom killer badness heuristic also uses this scale to report the oom
score for each eligible process in determining the "best" process to
kill. Thus, it can only differentiate each process's memory usage by
0.1% of system RAM.
On large systems, this can end up being a large amount of memory: 256MB
on 256GB systems, for example.
This can be fixed by having the badness heuristic to use the actual
memory usage in scoring threads and then normalizing it to the
oom_score_adj scale for userspace. This results in better comparison
between eligible threads for kill and no change from the userspace
perspective.
Suggested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove vmtruncate_range(), and remove the truncate_range method from
struct inode_operations: only tmpfs ever supported it, and tmpfs has now
converted over to using the fallocate method of file_operations.
Update Documentation accordingly, adding (setlease and) fallocate lines.
And while we're in mm.h, remove duplicate declarations of shmem_lock() and
shmem_file_setup(): everyone is now using the ones in shmem_fs.h.
Based-on-patch-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Cong Wang <amwang@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The GMA500 GPU driver uses GEM shmem objects, but with a new twist: the
backing RAM has to be below 4GB. Not a problem while the boards
supported only 4GB: but now Intel's D2700MUD boards support 8GB, and
their GMA3600 is managed by the GMA500 driver.
shmem/tmpfs has never pretended to support hardware restrictions on the
backing memory, but it might have appeared to do so before v3.1, and
even now it works fine until a page is swapped out then back in. When
read_cache_page_gfp() supplied a freshly allocated page for copy, that
compensated for whatever choice might have been made by earlier swapin
readahead; but swapoff was likely to destroy the illusion.
We'd like to continue to support GMA500, so now add a new
shmem_should_replace_page() check on the zone when about to move a page
from swapcache to filecache (in swapin and swapoff cases), with
shmem_replace_page() to allocate and substitute a suitable page (given
gma500/gem.c's mapping_set_gfp_mask GFP_KERNEL | __GFP_DMA32).
This does involve a minor extension to mem_cgroup_replace_page_cache()
(the page may or may not have already been charged); and I've removed a
comment and call to mem_cgroup_uncharge_cache_page(), which in fact is
always a no-op while PageSwapCache.
Also removed optimization of an unlikely path in shmem_getpage_gfp(),
now that we need to check PageSwapCache more carefully (a racing caller
might already have made the copy). And at one point shmem_unuse_inode()
needs to use the hitherto private page_swapcount(), to guard against
racing with inode eviction.
It would make sense to extend shmem_should_replace_page(), to cover
cpuset and NUMA mempolicy restrictions too, but set that aside for now:
needs a cleanup of shmem mempolicy handling, and more testing, and ought
to handle swap faults in do_swap_page() as well as shmem.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Stephane Marchesin <marcheu@chromium.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When MIGRATE_UNMOVABLE pages are freed from MIGRATE_UNMOVABLE type
pageblock (and some MIGRATE_MOVABLE pages are left in it) waiting until an
allocation takes ownership of the block may take too long. The type of
the pageblock remains unchanged so the pageblock cannot be used as a
migration target during compaction.
Fix it by:
* Adding enum compact_mode (COMPACT_ASYNC_[MOVABLE,UNMOVABLE], and
COMPACT_SYNC) and then converting sync field in struct compact_control
to use it.
* Adding nr_pageblocks_skipped field to struct compact_control and
tracking how many destination pageblocks were of MIGRATE_UNMOVABLE type.
If COMPACT_ASYNC_MOVABLE mode compaction ran fully in
try_to_compact_pages() (COMPACT_COMPLETE) it implies that there is not a
suitable page for allocation. In this case then check how if there were
enough MIGRATE_UNMOVABLE pageblocks to try a second pass in
COMPACT_ASYNC_UNMOVABLE mode.
* Scanning the MIGRATE_UNMOVABLE pageblocks (during COMPACT_SYNC and
COMPACT_ASYNC_UNMOVABLE compaction modes) and building a count based on
finding PageBuddy pages, page_count(page) == 0 or PageLRU pages. If all
pages within the MIGRATE_UNMOVABLE pageblock are in one of those three
sets change the whole pageblock type to MIGRATE_MOVABLE.
My particular test case (on a ARM EXYNOS4 device with 512 MiB, which means
131072 standard 4KiB pages in 'Normal' zone) is to:
- allocate 120000 pages for kernel's usage
- free every second page (60000 pages) of memory just allocated
- allocate and use 60000 pages from user space
- free remaining 60000 pages of kernel memory
(now we have fragmented memory occupied mostly by user space pages)
- try to allocate 100 order-9 (2048 KiB) pages for kernel's usage
The results:
- with compaction disabled I get 11 successful allocations
- with compaction enabled - 14 successful allocations
- with this patch I'm able to get all 100 successful allocations
NOTE: If we can make kswapd aware of order-0 request during compaction, we
can enhance kswapd with changing mode to COMPACT_ASYNC_FULL
(COMPACT_ASYNC_MOVABLE + COMPACT_ASYNC_UNMOVABLE). Please see the
following thread:
http://marc.info/?l=linux-mm&m=133552069417068&w=2
[minchan@kernel.org: minor cleanups]
Cc: Mel Gorman <mgorman@suse.de>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alloc_bootmem_section() derives allocation area constraints from the
specified sparsemem section. This is a bit specific for a generic memory
allocator like bootmem, though, so move it over to sparsemem.
As __alloc_bootmem_node_nopanic() already retries failed allocations with
relaxed area constraints, the fallback code in sparsemem.c can be removed
and the code becomes a bit more compact overall.
[akpm@linux-foundation.org: fix build]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When transparent_hugepage_enabled() is used outside mm/, such as in
arch/x86/xx/tlb.c:
+ if (!cpu_has_invlpg || vma->vm_flags & VM_HUGETLB
+ || transparent_hugepage_enabled(vma)) {
+ flush_tlb_mm(vma->vm_mm);
is_vma_temporary_stack() isn't referenced in huge_mm.h, so it has compile
errors:
arch/x86/mm/tlb.c: In function `flush_tlb_range':
arch/x86/mm/tlb.c:324:4: error: implicit declaration of function `is_vma_temporary_stack' [-Werror=implicit-function-declaration]
Since is_vma_temporay_stack() is just used in rmap.c and huge_memory.c, it
is better to move it to huge_mm.h from rmap.h to avoid such errors.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Programs using /proc/kpageflags need to know about the various flags. The
<linux/kernel-page-flags.h> provides them and the comments in the file
indicate that it is supposed to be used by user-level code. But the file
is not installed.
Install the headers and mark the unstable flags as out-of-bounds. The
page-type tool is also adjusted to not duplicate the definitions
Signed-off-by: Ulrich Drepper <drepper@gmail.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Even if CONFIG_DEBUG_VM=n gcc genereates code for some VM_BUG_ON()
for example VM_BUG_ON(!PageCompound(page) || !PageHead(page)); in
do_huge_pmd_wp_page() generates 114 bytes of code.
But they mostly disappears when I split this VM_BUG_ON into two:
-VM_BUG_ON(!PageCompound(page) || !PageHead(page));
+VM_BUG_ON(!PageCompound(page));
+VM_BUG_ON(!PageHead(page));
weird... but anyway after this patch code disappears completely.
add/remove: 0/0 grow/shrink: 7/97 up/down: 135/-1784 (-1649)
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes we want to check some expressions correctness at compile time.
"(void)(e);" or "if (e);" can be dangerous if the expression has
side-effects, and gcc sometimes generates a lot of code, even if the
expression has no effect.
This patch introduces macro BUILD_BUG_ON_INVALID() for such checks, it
forces a compilation error if expression is invalid without any extra
code.
[Cast to "long" required because sizeof does not work for bit-fields.]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rmap walker checking page table references has historically ignored
references from VMAs that were not part of the memcg that was being
reclaimed during memcg hard limit reclaim.
When transitioning global reclaim to memcg hierarchy reclaim, I missed
that bit and now references from outside a memcg are ignored even during
global reclaim.
Reverting back to traditional behaviour - count all references during
global reclaim and only mind references of the memcg being reclaimed
during limit reclaim would be one option.
However, the more generic idea is to ignore references exactly then when
they are outside the hierarchy that is currently under reclaim; because
only then will their reclamation be of any use to help the pressure
situation. It makes no sense to ignore references from a sibling memcg
and then evict a page that will be immediately refaulted by that sibling
which contributes to the same usage of the common ancestor under
reclaim.
The solution: make the rmap walker ignore references from VMAs that are
not part of the hierarchy that is being reclaimed.
Flat limit reclaim will stay the same, hierarchical limit reclaim will
mind the references only to pages that the hierarchy owns. Global
reclaim, since it reclaims from all memcgs, will be fixed to regard all
references.
[akpm@linux-foundation.org: name the args in the declaration]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Konstantin Khlebnikov<khlebnikov@openvz.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
s/from_nodes/from and s/to_nodes/to/. The "_nodes" is redundant - it
duplicates the argument's type.
Done in a fit of irritation over 80-col issues :(
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <mkosaki@redhat.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is little motiviation for reclaim_mode_t once RECLAIM_MODE_[A]SYNC
and lumpy reclaim have been removed. This patch gets rid of
reclaim_mode_t as well and improves the documentation about what
reclaim/compaction is and when it is triggered.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch stops reclaim/compaction entering sync reclaim as this was
only intended for lumpy reclaim and an oversight. Page migration has
its own logic for stalling on writeback pages if necessary and memory
compaction is already using it.
Waiting on page writeback is bad for a number of reasons but the primary
one is that waiting on writeback to a slow device like USB can take a
considerable length of time. Page reclaim instead uses
wait_iff_congested() to throttle if too many dirty pages are being
scanned.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This series removes lumpy reclaim and some stalling logic that was
unintentionally being used by memory compaction. The end result is that
stalling on dirty pages during page reclaim now depends on
wait_iff_congested().
Four kernels were compared
3.3.0 vanilla
3.4.0-rc2 vanilla
3.4.0-rc2 lumpyremove-v2 is patch one from this series
3.4.0-rc2 nosync-v2r3 is the full series
Removing lumpy reclaim saves almost 900 bytes of text whereas the full
series removes 1200 bytes.
text data bss dec hex filename
6740375 1927944 2260992 10929311 a6c49f vmlinux-3.4.0-rc2-vanilla
6739479 1927944 2260992 10928415 a6c11f vmlinux-3.4.0-rc2-lumpyremove-v2
6739159 1927944 2260992 10928095 a6bfdf vmlinux-3.4.0-rc2-nosync-v2
There are behaviour changes in the series and so tests were run with
monitoring of ftrace events. This disrupts results so the performance
results are distorted but the new behaviour should be clearer.
fs-mark running in a threaded configuration showed little of interest as
it did not push reclaim aggressively
FS-Mark Multi Threaded
3.3.0-vanilla rc2-vanilla lumpyremove-v2r3 nosync-v2r3
Files/s min 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%)
Files/s mean 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%)
Files/s stddev 0.00 ( 0.00%) 0.00 ( 0.00%) 0.00 ( 0.00%) 0.00 ( 0.00%)
Files/s max 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%) 3.20 ( 0.00%)
Overhead min 508667.00 ( 0.00%) 521350.00 (-2.49%) 544292.00 (-7.00%) 547168.00 (-7.57%)
Overhead mean 551185.00 ( 0.00%) 652690.73 (-18.42%) 991208.40 (-79.83%) 570130.53 (-3.44%)
Overhead stddev 18200.69 ( 0.00%) 331958.29 (-1723.88%) 1579579.43 (-8578.68%) 9576.81 (47.38%)
Overhead max 576775.00 ( 0.00%) 1846634.00 (-220.17%) 6901055.00 (-1096.49%) 585675.00 (-1.54%)
MMTests Statistics: duration
Sys Time Running Test (seconds) 309.90 300.95 307.33 298.95
User+Sys Time Running Test (seconds) 319.32 309.67 315.69 307.51
Total Elapsed Time (seconds) 1187.85 1193.09 1191.98 1193.73
MMTests Statistics: vmstat
Page Ins 80532 82212 81420 79480
Page Outs 111434984 111456240 111437376 111582628
Swap Ins 0 0 0 0
Swap Outs 0 0 0 0
Direct pages scanned 44881 27889 27453 34843
Kswapd pages scanned 25841428 25860774 25861233 25843212
Kswapd pages reclaimed 25841393 25860741 25861199 25843179
Direct pages reclaimed 44881 27889 27453 34843
Kswapd efficiency 99% 99% 99% 99%
Kswapd velocity 21754.791 21675.460 21696.029 21649.127
Direct efficiency 100% 100% 100% 100%
Direct velocity 37.783 23.375 23.031 29.188
Percentage direct scans 0% 0% 0% 0%
ftrace showed that there was no stalling on writeback or pages submitted
for IO from reclaim context.
postmark was similar and while it was more interesting, it also did not
push reclaim heavily.
POSTMARK
3.3.0-vanilla rc2-vanilla lumpyremove-v2r3 nosync-v2r3
Transactions per second: 16.00 ( 0.00%) 20.00 (25.00%) 18.00 (12.50%) 17.00 ( 6.25%)
Data megabytes read per second: 18.80 ( 0.00%) 24.27 (29.10%) 22.26 (18.40%) 20.54 ( 9.26%)
Data megabytes written per second: 35.83 ( 0.00%) 46.25 (29.08%) 42.42 (18.39%) 39.14 ( 9.24%)
Files created alone per second: 28.00 ( 0.00%) 38.00 (35.71%) 34.00 (21.43%) 30.00 ( 7.14%)
Files create/transact per second: 8.00 ( 0.00%) 10.00 (25.00%) 9.00 (12.50%) 8.00 ( 0.00%)
Files deleted alone per second: 556.00 ( 0.00%) 1224.00 (120.14%) 3062.00 (450.72%) 6124.00 (1001.44%)
Files delete/transact per second: 8.00 ( 0.00%) 10.00 (25.00%) 9.00 (12.50%) 8.00 ( 0.00%)
MMTests Statistics: duration
Sys Time Running Test (seconds) 113.34 107.99 109.73 108.72
User+Sys Time Running Test (seconds) 145.51 139.81 143.32 143.55
Total Elapsed Time (seconds) 1159.16 899.23 980.17 1062.27
MMTests Statistics: vmstat
Page Ins 13710192 13729032 13727944 13760136
Page Outs 43071140 42987228 42733684 42931624
Swap Ins 0 0 0 0
Swap Outs 0 0 0 0
Direct pages scanned 0 0 0 0
Kswapd pages scanned 99416139937443 9939085 9929154
Kswapd pages reclaimed 9940926 9936751 9938397 9928465
Direct pages reclaimed 0 0 0 0
Kswapd efficiency 99% 99% 99% 99%
Kswapd velocity 8576.567 11051.058 10140.164 9347.109
Direct efficiency 100% 100% 100% 100%
Direct velocity 0.000 0.000 0.000 0.000
It looks like here that the full series regresses performance but as
ftrace showed no usage of wait_iff_congested() or sync reclaim I am
assuming it's a disruption due to monitoring. Other data such as memory
usage, page IO, swap IO all looked similar.
Running a benchmark with a plain DD showed nothing very interesting.
The full series stalled in wait_iff_congested() slightly less but stall
times on vanilla kernels were marginal.
Running a benchmark that hammered on file-backed mappings showed stalls
due to congestion but not in sync writebacks
MICRO
3.3.0-vanilla rc2-vanilla lumpyremove-v2r3 nosync-v2r3
MMTests Statistics: duration
Sys Time Running Test (seconds) 308.13 294.50 298.75 299.53
User+Sys Time Running Test (seconds) 330.45 316.28 318.93 320.79
Total Elapsed Time (seconds) 1814.90 1833.88 1821.14 1832.91
MMTests Statistics: vmstat
Page Ins 108712 120708 97224 110344
Page Outs 155514576 156017404 155813676 156193256
Swap Ins 0 0 0 0
Swap Outs 0 0 0 0
Direct pages scanned 2599253 1550480 2512822 2414760
Kswapd pages scanned 69742364 71150694 68839041 69692533
Kswapd pages reclaimed 34824488 34773341 34796602 34799396
Direct pages reclaimed 53693 94750 61792 75205
Kswapd efficiency 49% 48% 50% 49%
Kswapd velocity 38427.662 38797.901 37799.972 38022.889
Direct efficiency 2% 6% 2% 3%
Direct velocity 1432.174 845.464 1379.807 1317.446
Percentage direct scans 3% 2% 3% 3%
Page writes by reclaim 0 0 0 0
Page writes file 0 0 0 0
Page writes anon 0 0 0 0
Page reclaim immediate 0 0 0 1218
Page rescued immediate 0 0 0 0
Slabs scanned 15360 16384 13312 16384
Direct inode steals 0 0 0 0
Kswapd inode steals 4340 4327 1630 4323
FTrace Reclaim Statistics: congestion_wait
Direct number congest waited 0 0 0 0
Direct time congest waited 0ms 0ms 0ms 0ms
Direct full congest waited 0 0 0 0
Direct number conditional waited 900 870 754 789
Direct time conditional waited 0ms 0ms 0ms 20ms
Direct full conditional waited 0 0 0 0
KSwapd number congest waited 2106 2308 2116 1915
KSwapd time congest waited 139924ms 157832ms 125652ms 132516ms
KSwapd full congest waited 1346 1530 1202 1278
KSwapd number conditional waited 12922 16320 10943 14670
KSwapd time conditional waited 0ms 0ms 0ms 0ms
KSwapd full conditional waited 0 0 0 0
Reclaim statistics are not radically changed. The stall times in kswapd
are massive but it is clear that it is due to calls to congestion_wait()
and that is almost certainly the call in balance_pgdat(). Otherwise
stalls due to dirty pages are non-existant.
I ran a benchmark that stressed high-order allocation. This is very
artifical load but was used in the past to evaluate lumpy reclaim and
compaction. Generally I look at allocation success rates and latency
figures.
STRESS-HIGHALLOC
3.3.0-vanilla rc2-vanilla lumpyremove-v2r3 nosync-v2r3
Pass 1 81.00 ( 0.00%) 28.00 (-53.00%) 24.00 (-57.00%) 28.00 (-53.00%)
Pass 2 82.00 ( 0.00%) 39.00 (-43.00%) 38.00 (-44.00%) 43.00 (-39.00%)
while Rested 88.00 ( 0.00%) 87.00 (-1.00%) 88.00 ( 0.00%) 88.00 ( 0.00%)
MMTests Statistics: duration
Sys Time Running Test (seconds) 740.93 681.42 685.14 684.87
User+Sys Time Running Test (seconds) 2922.65 3269.52 3281.35 3279.44
Total Elapsed Time (seconds) 1161.73 1152.49 1159.55 1161.44
MMTests Statistics: vmstat
Page Ins 4486020 2807256 2855944 2876244
Page Outs 7261600 7973688 7975320 7986120
Swap Ins 31694 0 0 0
Swap Outs 98179 0 0 0
Direct pages scanned 53494 57731 34406 113015
Kswapd pages scanned 6271173 1287481 1278174 1219095
Kswapd pages reclaimed 2029240 1281025 1260708 1201583
Direct pages reclaimed 1468 14564 16649 92456
Kswapd efficiency 32% 99% 98% 98%
Kswapd velocity 5398.133 1117.130 1102.302 1049.641
Direct efficiency 2% 25% 48% 81%
Direct velocity 46.047 50.092 29.672 97.306
Percentage direct scans 0% 4% 2% 8%
Page writes by reclaim 1616049 0 0 0
Page writes file 1517870 0 0 0
Page writes anon 98179 0 0 0
Page reclaim immediate 103778 27339 9796 17831
Page rescued immediate 0 0 0 0
Slabs scanned 1096704 986112 980992 998400
Direct inode steals 223 215040 216736 247881
Kswapd inode steals 175331 61548 68444 63066
Kswapd skipped wait 21991 0 1 0
THP fault alloc 1 135 125 134
THP collapse alloc 393 311 228 236
THP splits 25 13 7 8
THP fault fallback 0 0 0 0
THP collapse fail 3 5 7 7
Compaction stalls 865 1270 1422 1518
Compaction success 370 401 353 383
Compaction failures 495 869 1069 1135
Compaction pages moved 870155 3828868 4036106 4423626
Compaction move failure 26429 23865 29742 27514
Success rates are completely hosed for 3.4-rc2 which is almost certainly
due to commit fe2c2a1066 ("vmscan: reclaim at order 0 when compaction
is enabled"). I expected this would happen for kswapd and impair
allocation success rates (https://lkml.org/lkml/2012/1/25/166) but I did
not anticipate this much a difference: 80% less scanning, 37% less
reclaim by kswapd
In comparison, reclaim/compaction is not aggressive and gives up easily
which is the intended behaviour. hugetlbfs uses __GFP_REPEAT and would
be much more aggressive about reclaim/compaction than THP allocations
are. The stress test above is allocating like neither THP or hugetlbfs
but is much closer to THP.
Mainline is now impaired in terms of high order allocation under heavy
load although I do not know to what degree as I did not test with
__GFP_REPEAT. Keep this in mind for bugs related to hugepage pool
resizing, THP allocation and high order atomic allocation failures from
network devices.
In terms of congestion throttling, I see the following for this test
FTrace Reclaim Statistics: congestion_wait
Direct number congest waited 3 0 0 0
Direct time congest waited 0ms 0ms 0ms 0ms
Direct full congest waited 0 0 0 0
Direct number conditional waited 957 512 1081 1075
Direct time conditional waited 0ms 0ms 0ms 0ms
Direct full conditional waited 0 0 0 0
KSwapd number congest waited 36 4 3 5
KSwapd time congest waited 3148ms 400ms 300ms 500ms
KSwapd full congest waited 30 4 3 5
KSwapd number conditional waited 88514 197 332 542
KSwapd time conditional waited 4980ms 0ms 0ms 0ms
KSwapd full conditional waited 49 0 0 0
The "conditional waited" times are the most interesting as this is
directly impacted by the number of dirty pages encountered during scan.
As lumpy reclaim is no longer scanning contiguous ranges, it is finding
fewer dirty pages. This brings wait times from about 5 seconds to 0.
kswapd itself is still calling congestion_wait() so it'll still stall but
it's a lot less.
In terms of the type of IO we were doing, I see this
FTrace Reclaim Statistics: mm_vmscan_writepage
Direct writes anon sync 0 0 0 0
Direct writes anon async 0 0 0 0
Direct writes file sync 0 0 0 0
Direct writes file async 0 0 0 0
Direct writes mixed sync 0 0 0 0
Direct writes mixed async 0 0 0 0
KSwapd writes anon sync 0 0 0 0
KSwapd writes anon async 91682 0 0 0
KSwapd writes file sync 0 0 0 0
KSwapd writes file async 822629 0 0 0
KSwapd writes mixed sync 0 0 0 0
KSwapd writes mixed async 0 0 0 0
In 3.2, kswapd was doing a bunch of async writes of pages but
reclaim/compaction was never reaching a point where it was doing sync
IO. This does not guarantee that reclaim/compaction was not calling
wait_on_page_writeback() but I would consider it unlikely. It indicates
that merging patches 2 and 3 to stop reclaim/compaction calling
wait_on_page_writeback() should be safe.
This patch:
Lumpy reclaim had a purpose but in the mind of some, it was to kick the
system so hard it trashed. For others the purpose was to complicate
vmscan.c. Over time it was giving softer shoes and a nicer attitude but
memory compaction needs to step up and replace it so this patch sends
lumpy reclaim to the farm.
The tracepoint format changes for isolating LRU pages with this patch
applied. Furthermore reclaim/compaction can no longer queue dirty pages
in pageout() if the underlying BDI is congested. Lumpy reclaim used
this logic and reclaim/compaction was using it in error.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The swap token code no longer fits in with the current VM model. It
does not play well with cgroups or the better NUMA placement code in
development, since we have only one swap token globally.
It also has the potential to mess with scalability of the system, by
increasing the number of non-reclaimable pages on the active and
inactive anon LRU lists.
Last but not least, the swap token code has been broken for a year
without complaints, as reported by Konstantin Khlebnikov. This suggests
we no longer have much use for it.
The days of sub-1G memory systems with heavy use of swap are over. If
we ever need thrashing reducing code in the future, we will have to
implement something that does scale.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Hugh Dickins <hughd@google.com>
Acked-by: Bob Picco <bpicco@meloft.net>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit f56f821feb ("mm: extend prefault helpers to fault in more than
PAGE_SIZE") added in the new functions: fault_in_multipages_writeable()
and fault_in_multipages_readable().
However, we currently see:
include/linux/pagemap.h:492: warning: 'ret' may be used uninitialized in this function
include/linux/pagemap.h:492: note: 'ret' was declared here
Unlike a lot of gcc nags, this one appears somewhat legit. i.e. passing
in an invalid negative value of "size" does make it look like all the
conditionals in there would be bypassed and the uninitialized value would
be returned.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At the beginning of __skb_cow, headroom gets set to a minimum of
NET_SKB_PAD. This causes unnecessary reallocations if the buffer was not
cloned and the headroom is just below NET_SKB_PAD, but still more than the
amount requested by the caller.
This was showing up frequently in my tests on VLAN tx, where
vlan_insert_tag calls skb_cow_head(skb, VLAN_HLEN).
Locally generated packets should have enough headroom, and for forward
paths, we already have NET_SKB_PAD bytes of headroom, so we don't need to
add any extra space here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Rh0r
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"Besides the usual cleanups, this one brings:
* Support for 5 new chipsets: Intel's ICH LPC and SCH Centerton,
ST-E's STAX211, Samsung's MAX77693 and TI's LM3533.
* Device tree support for the twl6040, tps65910, da9502 and ab8500
drivers.
* Fairly big tps56910, ab8500 and db8500 updates.
* i2c support for mc13xxx.
* Our regular update for the wm8xxx driver from Mark."
Fix up various conflicts with other trees, largely due to ab5500 removal
etc.
* tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (106 commits)
mfd: Fix build break of max77693 by adding REGMAP_I2C option
mfd: Fix twl6040 build failure
mfd: Fix max77693 build failure
mfd: ab8500-core should depend on MFD_DB8500_PRCMU
gpio: tps65910: dt: process gpio specific device node info
mfd: Remove the parsing of dt info for tps65910 gpio
mfd: Save device node parsed platform data for tps65910 sub devices
mfd: Add r_select to lm3533 platform data
gpio: Add Intel Centerton support to gpio-sch
mfd: Emulate active low IRQs as well as active high IRQs for wm831x
mfd: Mark two lm3533 zone registers as volatile
mfd: Fix return type of lm533 attribute is_visible
mfd: Enable Device Tree support in the ab8500-pwm driver
mfd: Enable Device Tree support in the ab8500-sysctrl driver
mfd: Add support for Device Tree to twl6040
mfd: Register the twl6040 child for the ASoC codec unconditionally
mfd: Allocate twl6040 IRQ numbers dynamically
mfd: twl6040 code cleanup in interrupt initialization part
mfd: Enable ab8500-gpadc driver for Device Tree
mfd: Prevent unassigned pointer from being used in ab8500-gpadc driver
...
New features include:
- Rewrite the O_DIRECT code so that it can share the same coalescing and
pNFS functionality as the page cache code.
- Allow the server to provide hints as to when we should use pNFS, and
when it is more efficient to read and write through the metadata
server.
- NFS cache consistency updates:
- Use the ctime to emulate a change attribute for NFSv2/v3 so that
all NFS versions can share the same cache management code.
- New cache management code will only look at the change attribute
and size attribute when deciding whether or not our cached data
is still valid or not.
- Don't request NFSv4 post-op attributes on writes in cases such as
O_DIRECT, where we don't care about data cache consistency, or
when we have a write delegation, and know that our cache is
still consistent.
- Don't request NFSv4 post-op attributes on operations such as
COMMIT, where there are no expected metadata updates.
- Don't request NFSv4 directory post-op attributes in cases where
the operations themselves already return change attribute updates:
i.e. operations such as OPEN, CREATE, REMOVE, LINK and RENAME.
- Speed up 'ls' and friends by using READDIR rather than READDIRPLUS
if we detect no attempts to lookup filenames.
- Improve the code sharing between NFSv2/v3 and v4 mounts
- NFSv4.1 state management efficiency improvements
- More patches in preparation for NFSv4/v4.1 migration functionality.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=suVW
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.5-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"New features include:
- Rewrite the O_DIRECT code so that it can share the same coalescing
and pNFS functionality as the page cache code.
- Allow the server to provide hints as to when we should use pNFS,
and when it is more efficient to read and write through the
metadata server.
- NFS cache consistency updates:
* Use the ctime to emulate a change attribute for NFSv2/v3 so that
all NFS versions can share the same cache management code.
* New cache management code will only look at the change attribute
and size attribute when deciding whether or not our cached data
is still valid or not.
* Don't request NFSv4 post-op attributes on writes in cases such as
O_DIRECT, where we don't care about data cache consistency, or
when we have a write delegation, and know that our cache is still
consistent.
* Don't request NFSv4 post-op attributes on operations such as
COMMIT, where there are no expected metadata updates.
* Don't request NFSv4 directory post-op attributes in cases where
the operations themselves already return change attribute
updates: i.e. operations such as OPEN, CREATE, REMOVE, LINK and
RENAME.
- Speed up 'ls' and friends by using READDIR rather than READDIRPLUS
if we detect no attempts to lookup filenames.
- Improve the code sharing between NFSv2/v3 and v4 mounts
- NFSv4.1 state management efficiency improvements
- More patches in preparation for NFSv4/v4.1 migration functionality."
Fix trivial conflict in fs/nfs/nfs4proc.c that was due to the dcache
qstr name initialization changes (that made the length/hash a 64-bit
union)
* tag 'nfs-for-3.5-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (146 commits)
NFSv4: Add debugging printks to state manager
NFSv4: Map NFS4ERR_SHARE_DENIED into an EACCES error instead of EIO
NFSv4: update_changeattr does not need to set NFS_INO_REVAL_PAGECACHE
NFSv4.1: nfs4_reset_session should use nfs4_handle_reclaim_lease_error
NFSv4.1: Handle other occurrences of NFS4ERR_CONN_NOT_BOUND_TO_SESSION
NFSv4.1: Handle NFS4ERR_CONN_NOT_BOUND_TO_SESSION in the state manager
NFSv4.1: Handle errors in nfs4_bind_conn_to_session
NFSv4.1: nfs4_bind_conn_to_session should drain the session
NFSv4.1: Don't clobber the seqid if exchange_id returns a confirmed clientid
NFSv4.1: Add DESTROY_CLIENTID
NFSv4.1: Ensure we use the correct credentials for bind_conn_to_session
NFSv4.1: Ensure we use the correct credentials for session create/destroy
NFSv4.1: Move NFSPROC4_CLNT_BIND_CONN_TO_SESSION to the end of the operations
NFSv4.1: Handle NFS4ERR_SEQ_MISORDERED when confirming the lease
NFSv4: When purging the lease, we must clear NFS4CLNT_LEASE_CONFIRM
NFSv4: Clean up the error handling for nfs4_reclaim_lease
NFSv4.1: Exchange ID must use GFP_NOFS allocation mode
nfs41: Use BIND_CONN_TO_SESSION for CB_PATH_DOWN*
nfs4.1: add BIND_CONN_TO_SESSION operation
NFSv4.1 test the mdsthreshold hint parameters
...
While userspace doesn't fill the dimm labels, add there the dimm location,
as described by the used memory model. This could eventually match what
is described at the dmidecode, making easier for people to identify the
memory.
For example, on an Intel motherboard where the DMI table is reliable,
the first memory stick is described as:
Memory Device
Array Handle: 0x0029
Error Information Handle: Not Provided
Total Width: 64 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: DIMM
Set: 1
Locator: A1_DIMM0
Bank Locator: A1_Node0_Channel0_Dimm0
Type: <OUT OF SPEC>
Type Detail: Synchronous
Speed: 800 MHz
Manufacturer: A1_Manufacturer0
Serial Number: A1_SerNum0
Asset Tag: A1_AssetTagNum0
Part Number: A1_PartNum0
The memory named as "A1_DIMM0" is physically located at the first
memory controller (node 0), at channel 0, dimm slot 0.
After this patch, the memory label will be filled with:
/sys/devices/system/edac/mc/csrow0/ch0_dimm_label:mc#0channel#0slot#0
And (after the new EDAC API patches) as:
/sys/devices/system/edac/mc/mc0/dimm0/dimm_label:mc#0channel#0slot#0
So, even if the memory label is not initialized on userspace, an useful
information with the error location is filled there, expecially since
several systems/motherboards are provided with enough info to map from
channel/slot (or branch/channel/slot) into the DIMM label. So, letting the
EDAC core fill it by default is a good thing.
It should noticed that, as the label filling happens at the
edac_mc_alloc(), drivers can override it to better describe the memories
(and some actually do it).
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the EDAC internal representation to work with non-csrow
based memory controllers.
There are lots of those memory controllers nowadays, and more
are coming. So, the EDAC internal representation needs to be
changed, in order to work with those memory controllers, while
preserving backward compatibility with the old ones.
The edac core was written with the idea that memory controllers
are able to directly access csrows.
This is not true for FB-DIMM and RAMBUS memory controllers.
Also, some recent advanced memory controllers don't present a per-csrows
view. Instead, they view memories as DIMMs, instead of ranks.
So, change the allocation and error report routines to allow
them to work with all types of architectures.
This will allow the removal of several hacks with FB-DIMM and RAMBUS
memory controllers.
Also, several tests were done on different platforms using different
x86 drivers.
TODO: a multi-rank DIMMs are currently represented by multiple DIMM
entries in struct dimm_info. That means that changing a label for one
rank won't change the same label for the other ranks at the same DIMM.
This bug is present since the beginning of the EDAC, so it is not a big
deal. However, on several drivers, it is possible to fix this issue, but
it should be a per-driver fix, as the csrow => DIMM arrangement may not
be equal for all. So, don't try to fix it here yet.
I tried to make this patch as short as possible, preceding it with
several other patches that simplified the logic here. Yet, as the
internal API changes, all drivers need changes. The changes are
generally bigger in the drivers for FB-DIMMs.
Cc: Aristeu Rozanski <arozansk@redhat.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Mark Gross <mark.gross@intel.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: Tim Small <tim@buttersideup.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Egor Martovetsky <egor@pasemi.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Joe Perches <joe@perches.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Niklas Söderlund" <niklas.soderlund@ericsson.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The edac core were written with the idea that memory controllers
are able to directly access csrows, and that the channels are
used inside a csrows select.
This is not true for FB-DIMM and RAMBUS memory controllers.
Also, some recent advanced memory controllers don't present a per-csrows
view. Instead, they view memories as DIMMs, instead of ranks, accessed
via csrow/channel.
So, changes are needed in order to allow the EDAC core to
work with all types of architectures.
In preparation for handling non-csrows based memory controllers,
add some memory structs and a macro:
enum hw_event_mc_err_type: describes the type of error
(corrected, uncorrected, fatal)
To be used by the new edac_mc_handle_error function;
enum edac_mc_layer: describes the type of a given memory
architecture layer (branch, channel, slot, csrow).
struct edac_mc_layer: describes the properties of a memory
layer (type, size, and if the layer
will be used on a virtual csrow.
EDAC_DIMM_PTR() - as the number of layers can vary from 1 to 3,
this macro converts from an address with up to 3 layers into
a linear address.
Reviewed-by: Borislav Petkov <bp@amd64.org>
Cc: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The number of pages is a dimm property. Move it to the dimm struct.
After this change, it is possible to add sysfs nodes for the DIMM's that
will properly represent the DIMM stick properties, including its size.
A TODO fix here is to properly represent dual-rank/quad-rank DIMMs when
the memory controller represents the memory via chip select rows.
Reviewed-by: Aristeu Rozanski <arozansk@redhat.com>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Mark Gross <mark.gross@intel.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: Tim Small <tim@buttersideup.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Egor Martovetsky <egor@pasemi.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Joe Perches <joe@perches.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Niklas Söderlund" <niklas.soderlund@ericsson.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On systems based on chip select rows, all channels need to use memories
with the same properties, otherwise the memories on channels A and B
won't be recognized.
However, such assumption is not true for all types of memory
controllers.
Controllers for FB-DIMM's don't have such requirements.
Also, modern Intel controllers seem to be capable of handling such
differences.
So, we need to get rid of storing the DIMM information into a per-csrow
data, storing it, instead at the right place.
The first step is to move grain, mtype, dtype and edac_mode to the
per-dimm struct.
Reviewed-by: Aristeu Rozanski <arozansk@redhat.com>
Reviewed-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Mark Gross <mark.gross@intel.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: Tim Small <tim@buttersideup.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Egor Martovetsky <egor@pasemi.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Joe Perches <joe@perches.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: James Bottomley <James.Bottomley@parallels.com>
Cc: "Niklas Söderlund" <niklas.soderlund@ericsson.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Mike Williams <mike@mikebwilliams.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The way a DIMM is currently represented implies that they're
linked into a per-csrow struct. However, some drivers don't see
csrows, as they're ridden behind some chip like the AMB's
on FBDIMM's, for example.
This forced drivers to fake^Wvirtualize a csrow struct, and to create
a mess under csrow/channel original's concept.
Move the DIMM labels into a per-DIMM struct, and add there
the real location of the socket, in terms of csrow/channel.
Latter patches will modify the location to properly represent the
memory architecture.
All other drivers will use a per-csrow type of location.
Some of those drivers will require a latter conversion, as
they also fake the csrows internally.
TODO: While this patch doesn't change the existing behavior, on
csrows-based memory controllers, a csrow/channel pair points to a memory
rank. There's a known bug at the EDAC core that allows having different
labels for the same DIMM, if it has more than one rank. A latter patch
is need to merge the several ranks for a DIMM into the same dimm_info
struct, in order to avoid having different labels for the same DIMM.
The edac_mc_alloc() will now contain a per-dimm initialization loop that
will be changed by latter patches in order to match other types of
memory architectures.
Reviewed-by: Aristeu Rozanski <arozansk@redhat.com>
Reviewed-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Doug Thompson <norsk5@yahoo.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: "Niklas Söderlund" <niklas.soderlund@ericsson.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oLXf
-----END PGP SIGNATURE-----
Merge tag 'writeback' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux
Pull writeback tree from Wu Fengguang:
"Mainly from Jan Kara to avoid iput() in the flusher threads."
* tag 'writeback' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
writeback: Avoid iput() from flusher thread
vfs: Rename end_writeback() to clear_inode()
vfs: Move waiting for inode writeback from end_writeback() to evict_inode()
writeback: Refactor writeback_single_inode()
writeback: Remove wb->list_lock from writeback_single_inode()
writeback: Separate inode requeueing after writeback
writeback: Move I_DIRTY_PAGES handling
writeback: Move requeueing when I_SYNC set to writeback_sb_inodes()
writeback: Move clearing of I_SYNC into inode_sync_complete()
writeback: initialize global_dirty_limit
fs: remove 8 bytes of padding from struct writeback_control on 64 bit builds
mm: page-writeback.c: local functions should not be exposed globally
Lots of normal development commits, but perhaps most notable changes are:
* HDMI rework to properly decouple the HDMI audio part from the HDMI video part.
* Restructure omapdss core driver so that it's possible to implement device
tree support. This included changing how platform data is passed to the
drivers, changing display device registration and improving the panel driver's
ability to configure the underlying video output interface.
* Basic support for DSI packet interleaving
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=I8Se
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.5' of git://github.com/tomba/linux into fbdev-next
Omapdss driver changes for 3.5 merge window.
Lots of normal development commits, but perhaps most notable changes are:
* HDMI rework to properly decouple the HDMI audio part from the HDMI video part.
* Restructure omapdss core driver so that it's possible to implement device
tree support. This included changing how platform data is passed to the
drivers, changing display device registration and improving the panel driver's
ability to configure the underlying video output interface.
* Basic support for DSI packet interleaving
Activate the metadata checksumming feature by adding it to ext4 and
jbd2's lists of supported features.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Calculate and verify a checksum covering the journal superblock.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Obtain a reference to the crc32c driver if needed for the v2 checksum.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The type of the length field of the fw_address_handler structure was
size_t, which restricted it to 32 bits on 32-bit architectures.
While making it u32 would match the userspace API, all calculations on
this field use 64 bits anyway, and the ability to use 4 GB or larger
address ranges is useful in the kernel.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Since commit ad0081e43a
"ipv6: Fragment locally generated tunnel-mode IPSec6 packets as needed"
the fragment of packets is incorrect.
because tunnel mode needs IPsec headers and trailer for all fragments,
while on transport mode it is sufficient to add the headers to the
first fragment and the trailer to the last.
so modify mtu and maxfraglen base on ipsec mode and if fragment is first
or last.
with my test,it work well(every fragment's size is the mtu)
and does not trigger slow fragment path.
Changes from v1:
though optimization, mtu_prev and maxfraglen_prev can be delete.
replace xfrm mode codes with dst_entry's new frag DST_XFRM_TUNNEL.
add fuction ip6_append_data_mtu to make codes clearer.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes <asm/word-at-a-time.h> actually live up to its promise of
allowing architectures to help tune the string functions that do their
work a word at a time.
David had already taken the x86 strncpy_from_user() function, modified
it to work on sparc, and then done the extra work to make it generically
useful. This then expands on that work by making x86 use that generic
version, completing the circle.
But more importantly, it fixes up the word-at-a-time interfaces so that
it's now easy to also support things like strnlen_user(), and pretty
much most random string functions.
David reports that it all works fine on sparc, and Jonas Bonn reported
that an earlier version of this worked on OpenRISC too. It's pretty
easy for architectures to add support for this and just replace their
private versions with the generic code.
* generic-string-functions:
sparc: use the new generic strnlen_user() function
x86: use the new generic strnlen_user() function
lib: add generic strnlen_user() function
word-at-a-time: make the interfaces truly generic
x86: use generic strncpy_from_user routine
Pull i2c-embedded changes from Wolfram Sang:
"Major changes:
- lots of devicetree additions for existing drivers. I tried hard to
make sure the bindings are proper. In more complicated cases, I
requested acks from people having more experience with them than
me. That took a bit of extra time and also some time went into
discussions with developers about what bindings are and what not.
I have the feeling that the workflow with bindings should be
improved to scale better. I will spend some more thought on
this...
- i2c-muxes are succesfully used meanwhile, so we dropped
EXPERIMENTAL for them and renamed the drivers to a standard pattern
to match the rest of the subsystem. They can also be used with
devicetree now.
- ixp2000 was removed since the whole platform goes away.
- cleanups (strlcpy instead of strcpy, NULL instead of 0)
- The rest is typical driver fixes I assume.
All patches have been in linux-next at least since v3.4-rc6."
Fixed up trivial conflict in arch/arm/mach-lpc32xx/common.c due to the
same patch already having come in through the arm/soc trees, with
additional patches on top of it.
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (35 commits)
i2c: davinci: Free requested IRQ in remove
i2c: ocores: register OF i2c devices
i2c: tegra: notify transfer-complete after clearing status.
I2C: xiic: Add OF binding support
i2c: Rename last mux driver to standard pattern
i2c: tegra: fix 10bit address configuration
i2c: muxes: rename first set of drivers to a standard pattern
of/i2c: implement of_find_i2c_adapter_by_node
i2c: implement i2c_verify_adapter
i2c-s3c2410: Add HDMIPHY quirk for S3C2440
i2c-s3c2410: Rework device type handling
i2c: muxes are not EXPERIMENTAL anymore
i2c/of: Automatically populate i2c mux busses from device tree data.
i2c: Add a struct device * parameter to i2c_add_mux_adapter()
of/i2c: call i2c_verify_client from of_find_i2c_device_by_node
i2c: designware: Add clk_{un}prepare() support
i2c: designware: add PM support
i2c: ixp2000: remove driver
i2c: pnx: add device tree support
i2c: imx: don't use strcpy but strlcpy
...
These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WeDQ
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc device tree conversions (part 2) from Olof Johansson:
"These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier."
Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
...
A number of devices are using a common register layout, this adds support
code for it in lib/stmp_device.c so we do not need to duplicate it in
each driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=VHLM
-----END PGP SIGNATURE-----
Merge tag 'stmp-dev' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc stmp-dev library code from Olof Johansson:
"A number of devices are using a common register layout, this adds
support code for it in lib/stmp_device.c so we do not need to
duplicate it in each driver."
Fix up trivial conflicts in drivers/i2c/busses/i2c-mxs.c and
lib/Makefile
* tag 'stmp-dev' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
i2c: mxs: use global reset function
lib: add support for stmp-style devices
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
This changes the interfaces in <asm/word-at-a-time.h> to be a bit more
complicated, but a lot more generic.
In particular, it allows us to really do the operations efficiently on
both little-endian and big-endian machines, pretty much regardless of
machine details. For example, if you can rely on a fast population
count instruction on your architecture, this will allow you to make your
optimized <asm/word-at-a-time.h> file with that.
NOTE! The "generic" version in include/asm-generic/word-at-a-time.h is
not truly generic, it actually only works on big-endian. Why? Because
on little-endian the generic algorithms are wasteful, since you can
inevitably do better. The x86 implementation is an example of that.
(The only truly non-generic part of the asm-generic implementation is
the "find_zero()" function, and you could make a little-endian version
of it. And if the Kbuild infrastructure allowed us to pick a particular
header file, that would be lovely)
The <asm/word-at-a-time.h> functions are as follows:
- WORD_AT_A_TIME_CONSTANTS: specific constants that the algorithm
uses.
- has_zero(): take a word, and determine if it has a zero byte in it.
It gets the word, the pointer to the constant pool, and a pointer to
an intermediate "data" field it can set.
This is the "quick-and-dirty" zero tester: it's what is run inside
the hot loops.
- "prep_zero_mask()": take the word, the data that has_zero() produced,
and the constant pool, and generate an *exact* mask of which byte had
the first zero. This is run directly *outside* the loop, and allows
the "has_zero()" function to answer the "is there a zero byte"
question without necessarily getting exactly *which* byte is the
first one to contain a zero.
If you do multiple byte lookups concurrently (eg "hash_name()", which
looks for both NUL and '/' bytes), after you've done the prep_zero_mask()
phase, the result of those can be or'ed together to get the "either
or" case.
- The result from "prep_zero_mask()" can then be fed into "find_zero()"
(to find the byte offset of the first byte that was zero) or into
"zero_bytemask()" (to find the bytemask of the bytes preceding the
zero byte).
The existence of zero_bytemask() is optional, and is not necessary
for the normal string routines. But dentry name hashing needs it, so
if you enable DENTRY_WORD_AT_A_TIME you need to expose it.
This changes the generic strncpy_from_user() function and the dentry
hashing functions to use these modified word-at-a-time interfaces. This
gets us back to the optimized state of the x86 strncpy that we lost in
the previous commit when moving over to the generic version.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the EXCHGID4_FLAG_CONFIRMED_R flag is set, the client is in theory
supposed to already know the correct value of the seqid, in which case
RFC5661 states that it should ignore the value returned.
Also ensure that if the sanity check in nfs4_check_cl_exchange_flags
fails, then we must not change the nfs_client fields.
Finally, clean up the code: we don't need to retest the value of
'status' unless it can change.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Pull tile updates from Chris Metcalf:
"These changes cover a range of new arch/tile features and
optimizations. They've been through LKML review and on linux-next for
a month or so. There's also one bug-fix that just missed 3.4, which
I've marked for stable."
Fixed up trivial conflict in arch/tile/Kconfig (new added tile Kconfig
entries clashing with the generic timer/clockevents changes).
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: default to tilegx_defconfig for ARCH=tile
tile: fix bug where fls(0) was not returning 0
arch/tile: mark TILEGX as not EXPERIMENTAL
tile/mm/fault.c: Port OOM changes to handle_page_fault
arch/tile: add descriptive text if the kernel reports a bad trap
arch/tile: allow querying cpu module information from the hypervisor
arch/tile: fix hardwall for tilegx and generalize for idn and ipi
arch/tile: support multiple huge page sizes dynamically
mm: add new arch_make_huge_pte() method for tile support
arch/tile: support kexec() for tilegx
arch/tile: support <asm/cachectl.h> header for cacheflush() syscall
arch/tile: Allow tilegx to build with either 16K or 64K page size
arch/tile: optimize get_user/put_user and friends
arch/tile: support building big-endian kernel
arch/tile: allow building Linux with transparent huge pages enabled
arch/tile: use interrupt critical sections less
The tile support for multiple-size huge pages requires tagging
the hugetlb PTE with a "super" bit for PTEs that are multiples of
the basic size of a pagetable span. To set that bit properly
we need to tweak the PTe in make_huge_pte() based on the vma.
This change provides the API for a subsequent tile-specific
change to use.
Reviewed-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The change adds some infrastructure for managing tile pmd's more generally,
using pte_pmd() and pmd_pte() methods to translate pmd values to and
from ptes, since on TILEPro a pmd is really just a nested structure
holding a pgd (aka pte). Several existing pmd methods are moved into
this framework, and a whole raft of additional pmd accessors are defined
that are used by the transparent hugepage framework.
The tile PTE now has a "client2" bit. The bit is used to indicate a
transparent huge page is in the process of being split into subpages.
This change also fixes a generic bug where the return value of the
generic pmdp_splitting_flush() was incorrect.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPvzQCAAoJEFErWKtxJpJdpNEIAI1sKDywvfuJK0Ik76ICj1Yt
P//4/ZvROmT8w9u/Jw3BAG7K3u7NLtfht6RcrUFqMULjMUUQ/aymlY9uTbwFZ+so
WCsVh5tHCULa1oUnAUv8fGMgvGoufD4ZqI/9qbuYLmBtUwPAatul51cEmQyWVvLa
lJN8PzJ7whfYqNoXpR4SCp8eHY4iJ3DZFDhypdQfZbTgOTrzsoVIJnTdHUXsiRQQ
E3gB2dRvyihzOD/UFac47af5wVUwtvo1N6NdQ5tJxOX9ZhVGdHaxAqF5FTlWpm6F
uK100uqFHPbm/TZGtSrGD1ai8L7Hbl//LuzaODjLH9usCiYe6KzSSwf8Alg59Ws=
=hsWu
-----END PGP SIGNATURE-----
Merge tag 'tag-for-linus-3.5' of git://git.linaro.org/people/sumitsemwal/linux-dma-buf
Pull dma-buf updates from Sumit Semwal:
"Here's the first signed-tag pull request for dma-buf framework. It
includes the following key items:
- mmap support
- vmap support
- related documentation updates
These are needed by various drivers to allow mmap/vmap of dma-buf
shared buffers. Dave Airlie has some prime patches dependent on the
vmap pull as well."
* tag 'tag-for-linus-3.5' of git://git.linaro.org/people/sumitsemwal/linux-dma-buf:
dma-buf: add initial vmap documentation
dma-buf: minor documentation fixes.
dma-buf: add vmap interface
dma-buf: mmap support
Pull slave-dmaengine updates from Vinod Koul:
"Nothing exciting this time, odd fixes in a bunch of drivers"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: at_hdmac: take maxburst from slave configuration
dmaengine: at_hdmac: remove ATC_DEFAULT_CTRLA constant
dmaengine: at_hdmac: remove some at_dma_slave comments
dma: imx-sdma: make channel0 operations atomic
dmaengine: Fixup dmaengine_prep_slave_single() to be actually useful
dmaengine: Use dma_sg_len(sg) instead of sg->length
dmaengine: Use sg_dma_address instead of sg_phys
DMA: PL330: Remove duplicate header file inclusion
dma: imx-sdma: keep the callbacks invoked in the tasklet
dmaengine: dw_dma: add Device Tree probing capability
dmaengine: dw_dmac: Add clk_{un}prepare() support
dma/amba-pl08x: add support for the Nomadik variant
dma/amba-pl08x: check for terminal count status only
Pull CMA and ARM DMA-mapping updates from Marek Szyprowski:
"These patches contain two major updates for DMA mapping subsystem
(mainly for ARM architecture). First one is Contiguous Memory
Allocator (CMA) which makes it possible for device drivers to allocate
big contiguous chunks of memory after the system has booted.
The main difference from the similar frameworks is the fact that CMA
allows to transparently reuse the memory region reserved for the big
chunk allocation as a system memory, so no memory is wasted when no
big chunk is allocated. Once the alloc request is issued, the
framework migrates system pages to create space for the required big
chunk of physically contiguous memory.
For more information one can refer to nice LWN articles:
- 'A reworked contiguous memory allocator':
http://lwn.net/Articles/447405/
- 'CMA and ARM':
http://lwn.net/Articles/450286/
- 'A deep dive into CMA':
http://lwn.net/Articles/486301/
- and the following thread with the patches and links to all previous
versions:
https://lkml.org/lkml/2012/4/3/204
The main client for this new framework is ARM DMA-mapping subsystem.
The second part provides a complete redesign in ARM DMA-mapping
subsystem. The core implementation has been changed to use common
struct dma_map_ops based infrastructure with the recent updates for
new dma attributes merged in v3.4-rc2. This allows to use more than
one implementation of dma-mapping calls and change/select them on the
struct device basis. The first client of this new infractructure is
dmabounce implementation which has been completely cut out of the
core, common code.
The last patch of this redesign update introduces a new, experimental
implementation of dma-mapping calls on top of generic IOMMU framework.
This lets ARM sub-platform to transparently use IOMMU for DMA-mapping
calls if one provides required IOMMU hardware.
For more information please refer to the following thread:
http://www.spinics.net/lists/arm-kernel/msg175729.html
The last patch merges changes from both updates and provides a
resolution for the conflicts which cannot be avoided when patches have
been applied on the same files (mainly arch/arm/mm/dma-mapping.c)."
Acked by Andrew Morton <akpm@linux-foundation.org>:
"Yup, this one please. It's had much work, plenty of review and I
think even Russell is happy with it."
* 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping: (28 commits)
ARM: dma-mapping: use PMD size for section unmap
cma: fix migration mode
ARM: integrate CMA with DMA-mapping subsystem
X86: integrate CMA with DMA-mapping subsystem
drivers: add Contiguous Memory Allocator
mm: trigger page reclaim in alloc_contig_range() to stabilise watermarks
mm: extract reclaim code from __alloc_pages_direct_reclaim()
mm: Serialize access to min_free_kbytes
mm: page_isolation: MIGRATE_CMA isolation functions added
mm: mmzone: MIGRATE_CMA migration type added
mm: page_alloc: change fallbacks array handling
mm: page_alloc: introduce alloc_contig_range()
mm: compaction: export some of the functions
mm: compaction: introduce isolate_freepages_range()
mm: compaction: introduce map_pages()
mm: compaction: introduce isolate_migratepages_range()
mm: page_alloc: remove trailing whitespace
ARM: dma-mapping: add support for IOMMU mapper
ARM: dma-mapping: use alloc, mmap, free from dma_ops
ARM: dma-mapping: remove redundant code and do the cleanup
...
Conflicts:
arch/x86/include/asm/dma-mapping.h
Drivers:
- at91-mci: This driver will be replaced by atmel-mci in 3.7.
- atmel-mci: Add support for old at91-mci hardware.
- dw_mmc: Allow multiple controllers; this previously caused corruption.
- imxmmc: Remove this driver, replaced by mxcmmc.
- mmci: Add device tree support.
- omap: Allow multiple controllers.
- omap_hsmmc: Auto CMD12, DDR support.
- tegra: Support SD 3.0 spec.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rjPa
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC changes from Chris Ball
- at91-mci: This driver will be replaced by atmel-mci in 3.7.
- atmel-mci: Add support for old at91-mci hardware.
- dw_mmc: Allow multiple controllers; this previously caused
corruption.
- imxmmc: Remove this driver, replaced by mxcmmc.
- mmci: Add device tree support.
- omap: Allow multiple controllers.
- omap_hsmmc: Auto CMD12, DDR support.
- tegra: Support SD 3.0 spec.
Fix up the usual trivial conflicts in feature-removal-schedule.txt
* tag 'mmc-merge-for-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (38 commits)
mmc: at91-mci: this driver is now deprecated
mmc: omap_hsmmc: pass IRQF_ONESHOT to request_threaded_irq
mmc: block: Allow disabling 512B sector size emulation
mmc: atmel-mci: add debug logs
mmc: atmel-mci: add support for version lower than v2xx
mmc: atmel-mci: change the state machine for compatibility with old IP
mmc: atmel-mci: the r/w proof capability lack was not well managed
mmc: dw_mmc: Fixed sdio interrupt mask bit setting bug
mmc: omap: convert to module_platform_driver
mmc: omap: make it behave well as a module
mmc: omap: convert to per instance workqueue
mmc: core: Remove dead code
mmc: card: Avoid null pointer dereference
mmc: core: Prevent eMMC VCC supply to be cut from late init
mmc: dw_mmc: make multiple instances of dw_mci_card_workqueue
mmc: queue: remove redundant memsets
mmc: queue: rename mmc_request function
mmc: core: skip card initialization if power class selection fails
mmc: core: fix the signaling 1.8V for HS200
mmc: core: fix the decision of HS200/DDR card-type
...
Pull ext2, ext3 and quota fixes from Jan Kara:
"Interesting bits are:
- removal of a special i_mutex locking subclass (I_MUTEX_QUOTA) since
quota code does not need i_mutex anymore in any unusual way.
- backport (from ext4) of a fix of a checkpointing bug (missing cache
flush) that could lead to fs corruption on power failure
The rest are just random small fixes & cleanups."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext2: trivial fix to comment for ext2_free_blocks
ext2: remove the redundant comment for ext2_export_ops
ext3: return 32/64-bit dir name hash according to usage type
quota: Get rid of nested I_MUTEX_QUOTA locking subclass
quota: Use precomputed value of sb_dqopt in dquot_quota_sync
ext2: Remove i_mutex use from ext2_quota_write()
reiserfs: Remove i_mutex use from reiserfs_quota_write()
ext4: Remove i_mutex use from ext4_quota_write()
ext3: Remove i_mutex use from ext3_quota_write()
quota: Fix double lock in add_dquot_ref() with CONFIG_QUOTA_DEBUG
jbd: Write journal superblock with WRITE_FUA after checkpointing
jbd: protect all log tail updates with j_checkpoint_mutex
jbd: Split updating of journal superblock and marking journal empty
ext2: do not register write_super within VFS
ext2: Remove s_dirt handling
ext2: write superblock only once on unmount
ext3: update documentation with barrier=1 default
ext3: remove max_debt in find_group_orlov()
jbd: Refine commit writeout logic
This helps implement GL_ARB_sync but stops short of allowing full blown
sync objects. Finally we can use the new timed seqno waiting function
to allow userspace to wait on a buffer object with a timeout. This
implements that interface.
The IOCTL will take as input a buffer object handle, and a timeout in
nanoseconds (flags is currently optional but will likely be used for
permutations of flush operations). Users may specify 0 nanoseconds to
instantly check.
The wait ioctl with a timeout of 0 reimplements the busy ioctl. With any
non-zero timeout parameter the wait ioctl will wait for the given number
of nanoseconds on an object becoming unbusy. Since the wait itself does
so holding struct_mutex the object may become re-busied before this
completes. A similar but shorter race condition exists in the busy
ioctl.
v2: ETIME/ERESTARTSYS instead of changing to EBUSY, and EGAIN (Chris)
Flush the object from the gpu write domain (Chris + Daniel)
Fix leaked refcount in good case (Chris)
Naturally align ioctl struct (Chris)
v3: Drop lock after getting seqno to avoid ugly dance (Chris)
v4: check for 0 timeout after olr check to allow polling (Chris)
v5: Updated the comment. (Chris)
v6: Return -ETIME instead of -EBUSY when timeout_ns is 0 (Daniel)
Fix the commit message comment to be less ugly (Ben)
Add a warning to check the return timespec (Ben)
v7: Use DRM_AUTH for the ioctl. (Eugeni)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This introduces a new flag for clocks that need to have their divisor
ratio set back to their initial mask at disable time to prevent
interactivity problems with the clock stop bit (presently div6 only).
With this in place it's possible to handle the corner case on top of the
div4 op without any particular need for leaving things split out.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some minor inline documentation fixes for gaps resulting from new patches.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
The main requirement I have for this interface is for scanning out
using the USB gpu devices. Since these devices have to read the
framebuffer on updates and linearly compress it, using kmaps
is a major overhead for every update.
v2: fix warn issues pointed out by Sylwester Nawrocki.
v3: fix compile !CONFIG_DMA_SHARED_BUFFER and add _GPL for now
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Compared to Rob Clark's RFC I've ditched the prepare/finish hooks
and corresponding ioctls on the dma_buf file. The major reason for
that is that many people seem to be under the impression that this is
also for synchronization with outstanding asynchronous processsing.
I'm pretty massively opposed to this because:
- It boils down reinventing a new rather general-purpose userspace
synchronization interface. If we look at things like futexes, this
is hard to get right.
- Furthermore a lot of kernel code has to interact with this
synchronization primitive. This smells a look like the dri1 hw_lock,
a horror show I prefer not to reinvent.
- Even more fun is that multiple different subsystems would interact
here, so we have plenty of opportunities to create funny deadlock
scenarios.
I think synchronization is a wholesale different problem from data
sharing and should be tackled as an orthogonal problem.
Now we could demand that prepare/finish may only ensure cache
coherency (as Rob intended), but that runs up into the next problem:
We not only need mmap support to facilitate sw-only processing nodes
in a pipeline (without jumping through hoops by importing the dma_buf
into some sw-access only importer), which allows for a nicer
ION->dma-buf upgrade path for existing Android userspace. We also need
mmap support for existing importing subsystems to support existing
userspace libraries. And a loot of these subsystems are expected to
export coherent userspace mappings.
So prepare/finish can only ever be optional and the exporter /needs/
to support coherent mappings. Given that mmap access is always
somewhat fallback-y in nature I've decided to drop this optimization,
instead of just making it optional. If we demonstrate a clear need for
this, supported by benchmark results, we can always add it in again
later as an optional extension.
Other differences compared to Rob's RFC is the above mentioned support
for mapping a dma-buf through facilities provided by the importer.
Which results in mmap support no longer being optional.
Note that this dma-buf mmap patch does _not_ support every possible
insanity an existing subsystem could pull of with mmap: Because it
does not allow to intercept pagefaults and shoot down ptes importing
subsystems can't add some magic of their own at these points (e.g. to
automatically synchronize with outstanding rendering or set up some
special resources). I've done a cursory read through a few mmap
implementions of various subsytems and I'm hopeful that we can avoid
this (and the complexity it'd bring with it).
Additonally I've extended the documentation a bit to explain the hows
and whys of this mmap extension.
In case we ever want to add support for explicitly cache maneged
userspace mmap with a prepare/finish ioctl pair, we could specify that
userspace needs to mmap a different part of the dma_buf, e.g. the
range starting at dma_buf->size up to dma_buf->size*2. This works
because the size of a dma_buf is invariant over it's lifetime. The
exporter would obviously need to fall back to coherent mappings for
both ranges if a legacy clients maps the coherent range and the
architecture cannot suppor conflicting caching policies. Also, this
would obviously be optional and userspace needs to be able to fall
back to coherent mappings.
v2:
- Spelling fixes from Rob Clark.
- Compile fix for !DMA_BUF from Rob Clark.
- Extend commit message to explain how explicitly cache managed mmap
support could be added later.
- Extend the documentation with implementations notes for exporters
that need to manually fake coherency.
v3:
- dma_buf pointer initialization goof-up noticed by Rebecca Schultz
Zavin.
Cc: Rob Clark <rob.clark@linaro.org>
Cc: Rebecca Schultz Zavin <rebecca@android.com>
Acked-by: Rob Clark <rob.clark@linaro.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
This plugs in a div_mask for the clock and sets it up for the existing
div6/4 cases. This will make it possible to support other div types, as
well as share more div6/4 infrastructure.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in a generic clk_div_table, based on the div4 version. div6 is
then adopted to use it for encapsulating its div table, which permits us
to start div6/4 unification, as well as preparation for other div types.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pull KVM changes from Avi Kivity:
"Changes include additional instruction emulation, page-crossing MMIO,
faster dirty logging, preventing the watchdog from killing a stopped
guest, module autoload, a new MSI ABI, and some minor optimizations
and fixes. Outside x86 we have a small s390 and a very large ppc
update.
Regarding the new (for kvm) rebaseless workflow, some of the patches
that were merged before we switch trees had to be rebased, while
others are true pulls. In either case the signoffs should be correct
now."
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
arch/powerpc/kvm/book3s_segment.S and arch/x86/include/asm/kvm_para.h.
I suspect the kvm_para.h resolution ends up doing the "do I have cpuid"
check effectively twice (it was done differently in two different
commits), but better safe than sorry ;)
* 'next' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (125 commits)
KVM: make asm-generic/kvm_para.h have an ifdef __KERNEL__ block
KVM: s390: onereg for timer related registers
KVM: s390: epoch difference and TOD programmable field
KVM: s390: KVM_GET/SET_ONEREG for s390
KVM: s390: add capability indicating COW support
KVM: Fix mmu_reload() clash with nested vmx event injection
KVM: MMU: Don't use RCU for lockless shadow walking
KVM: VMX: Optimize %ds, %es reload
KVM: VMX: Fix %ds/%es clobber
KVM: x86 emulator: convert bsf/bsr instructions to emulate_2op_SrcV_nobyte()
KVM: VMX: unlike vmcs on fail path
KVM: PPC: Emulator: clean up SPR reads and writes
KVM: PPC: Emulator: clean up instruction parsing
kvm/powerpc: Add new ioctl to retreive server MMU infos
kvm/book3s: Make kernel emulated H_PUT_TCE available for "PR" KVM
KVM: PPC: bookehv: Fix r8/r13 storing in level exception handler
KVM: PPC: Book3S: Enable IRQs during exit handling
KVM: PPC: Fix PR KVM on POWER7 bare metal
KVM: PPC: Fix stbux emulation
KVM: PPC: bookehv: Use lwz/stw instead of PPC_LL/PPC_STL for 32-bit fields
...
* Extend the APIC ops implementation and add IRQ_WORKER vector support so that 'perf' can work properly.
* Fix self-ballooning code, and balloon logic when booting as initial domain.
* Move array printing code to generic debugfs
* Support XenBus domains.
* Lazily free grants when a domain is dead/non-existent.
* In M2P code use batching calls
Bug-fixes:
* Fix NULL dereference in allocation failure path (hvc_xen)
* Fix unbinding of IRQ_WORKER vector during vCPU hot-unplug
* Fix HVM guest resume - we would leak an PIRQ value instead of reusing the existing one.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPu9MpAAoJEFjIrFwIi8fJaNQH/RylThiO+O+LBpPrO8VRUw+2
/Io98T7ZK2ggoUeaJx0C8irM0JMFAkxGMcfX3w9fwNt/BTec4s++4JhbN1jYN0da
6a0PqINo+M8y73So6CBfuJDCunaRLGKVG/ibIO3Y3WAff51/H+DMvO7uYYDAE0aA
mikyOxnaty0DiG5i4JGDHGmCzDASfK/jgGccZ03m6522mDx5ZIbTzZWONLfz8dqT
rbxnn9vrNLgEYWuzyLMwW0GymToUtt01xBQvwJLAbhn8lr1WBRBLpxXA+5iYNQrn
Ri25G7keYJhG4uwZfaHnR+4HTrmhlGzK1Z96dkqpGUaeIcdyWmPMp22VtBBiwG8=
=uyRr
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.5-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen updates from Konrad Rzeszutek Wilk:
"Features:
* Extend the APIC ops implementation and add IRQ_WORKER vector
support so that 'perf' can work properly.
* Fix self-ballooning code, and balloon logic when booting as initial
domain.
* Move array printing code to generic debugfs
* Support XenBus domains.
* Lazily free grants when a domain is dead/non-existent.
* In M2P code use batching calls
Bug-fixes:
* Fix NULL dereference in allocation failure path (hvc_xen)
* Fix unbinding of IRQ_WORKER vector during vCPU hot-unplug
* Fix HVM guest resume - we would leak an PIRQ value instead of
reusing the existing one."
Fix up add-add onflicts in arch/x86/xen/enlighten.c due to addition of
apic ipi interface next to the new apic_id functions.
* tag 'stable/for-linus-3.5-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: do not map the same GSI twice in PVHVM guests.
hvc_xen: NULL dereference on allocation failure
xen: Add selfballoning memory reservation tunable.
xenbus: Add support for xenbus backend in stub domain
xen/smp: unbind irqworkX when unplugging vCPUs.
xen: enter/exit lazy_mmu_mode around m2p_override calls
xen/acpi/sleep: Enable ACPI sleep via the __acpi_os_prepare_sleep
xen: implement IRQ_WORK_VECTOR handler
xen: implement apic ipi interface
xen/setup: update VA mapping when releasing memory during setup
xen/setup: Combine the two hypercall functions - since they are quite similar.
xen/setup: Populate freed MFNs from non-RAM E820 entries and gaps to E820 RAM
xen/setup: Only print "Freeing XXX-YYY pfn range: Z pages freed" if Z > 0
xen/gnttab: add deferred freeing logic
debugfs: Add support to print u32 array in debugfs
xen/p2m: An early bootup variant of set_phys_to_machine
xen/p2m: Collapse early_alloc_p2m_middle redundant checks.
xen/p2m: Allow alloc_p2m_middle to call reserve_brk depending on argument
xen/p2m: Move code around to allow for better re-usage.
Pull sparc changes from David S. Miller:
"This has the generic strncpy_from_user() implementation architectures
can now use, which we've been developing on linux-arch over the past
few days.
For good measure I ran both a 32-bit and a 64-bit glibc testsuite run,
and the latter of which pointed out an adjustment I needed to make to
sparc's user_addr_max() definition. Linus, you were right, STACK_TOP
was not the right thing to use, even on sparc itself :-)
From Sam Ravnborg, we have a conversion of sparc32 over to the common
alloc_thread_info_node(), since the aspect which originally blocked
our doing so (sun4c) has been removed."
Fix up trivial arch/sparc/Kconfig and lib/Makefile conflicts.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Fix user_addr_max() definition.
lib: Sparc's strncpy_from_user is generic enough, move under lib/
kernel: Move REPEAT_BYTE definition into linux/kernel.h
sparc: Increase portability of strncpy_from_user() implementation.
sparc: Optimize strncpy_from_user() zero byte search.
sparc: Add full proper error handling to strncpy_from_user().
sparc32: use the common implementation of alloc_thread_info_node()
Lots of gpio changes, both to core code and drivers. Changes do touch
architecture code to remove the need for separate arm/gpio.h includes
in most architectures. Some new drivers are added, and a number of
gpio drivers are converted to use irq_domains for gpio inputs used as
interrupts. Device tree support has been amended to allow multiple
gpio_chips to use the same device tree node. Remaining changes are
primarily bug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=U6hj
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO driver changes from Grant Likely:
"Lots of gpio changes, both to core code and drivers.
Changes do touch architecture code to remove the need for separate
arm/gpio.h includes in most architectures.
Some new drivers are added, and a number of gpio drivers are converted
to use irq_domains for gpio inputs used as interrupts. Device tree
support has been amended to allow multiple gpio_chips to use the same
device tree node.
Remaining changes are primarily bug fixes."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (33 commits)
gpio/generic: initialize basic_mmio_gpio shadow variables properly
gpiolib: Remove 'const' from data argument of gpiochip_find()
gpio/rc5t583: add gpio driver for RICOH PMIC RC5T583
gpiolib: quiet gpiochip_add boot message noise
gpio: mpc8xxx: Prevent NULL pointer deref in demux handler
gpio/lpc32xx: Add device tree support
gpio: Adjust of_xlate API to support multiple GPIO chips
gpiolib: Implement devm_gpio_request_one()
gpio-mcp23s08: dbg_show: fix pullup configuration display
Add support for TCA6424A
gpio/omap: (re)fix wakeups on level-triggered GPIOs
gpio/omap: fix broken context restore for non-OFF mode transitions
gpio/omap: fix missing check in *_runtime_suspend()
gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()
gpio/omap: remove suspend/resume callbacks
gpio/omap: remove retrigger variable in gpio_irq_handler
gpio/omap: remove saved_wakeup field from struct gpio_bank
gpio/omap: remove suspend_wakeup field from struct gpio_bank
gpio/omap: remove saved_fallingdetect, saved_risingdetect
gpio/omap: remove virtual_irq_start variable
...
Conflicts:
drivers/gpio/gpio-samsung.c
Mostly documentation updates, but also includes an empty stub for
non-CONFIG_OF builds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=acqX
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull device tree changes from Grant Likely:
"Mostly documentation updates, but also includes an empty stub for
non-CONFIG_OF builds."
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6:
dt/documentation: Fix value format description
dt: add vendor prefix for EM Microelectronics
ARM: DT: Add binding for GIC virtualization extentions (VGIC)
of/irq: add empty irq_of_parse_and_map() for non-dt builds
Bug fixes and new features for SPI device drivers. Also move device
tree support code out of drivers/of and into drivers/spi/spi.c where
it makes more sense.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/Ux1
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI changes from Grant Likely:
"Bug fixes and new features for SPI device drivers. Also move device
tree support code out of drivers/of and into drivers/spi/spi.c where
it makes more sense."
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi: By default setup spi_masters with 1 chipselect and dynamics bus number
SPI: PRIMA2: use the newest APIs of PINCTRL to fix compiling errors
spi/spi-fsl-spi: reference correct pdata in fsl_spi_cs_control
spi: refactor spi-coldfire-qspi to use SPI queue framework.
spi/omap2-mcspi: convert to the pump message infrastructure
spi/rspi: add dmaengine support
spi/topcliff: use correct __devexit_p annotation
spi: Dont call prepare/unprepare transfer if not populated
spi/ep93xx: clean probe/remove routines
spi/devicetree: Move devicetree support code into spi directory
spi: use module_pci_driver
spi/omap2-mcspi: Trivial optimisation
spi: omap2-mcspi: add support for pm_runtime autosuspend
spi/omap: Remove bus_num usage for instance index
OMAP : SPI : use devm_* functions
spi: omap2-mcspi: convert to module_platform_driver
spi: omap2-mcspi: make it behave as a module
Minor changes and fixups for irqdomain infrastructure. Most
important change adds ability to remove registered irqdomain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=K3Pg
-----END PGP SIGNATURE-----
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull irqdomain changes from Grant Likely:
"Minor changes and fixups for irqdomain infrastructure. The most
important change adds the ability to remove a registered irqdomain."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6:
irqdomain: Document size parameter of irq_domain_add_linear()
irqdomain: trivial pr_fmt conversion.
irqdomain: Kill off duplicate definitions.
irqdomain: Make irq_domain_simple_map() static.
irqdomain: Export remaining public API symbols.
irqdomain: Support removal of IRQ domains.
Pull timer updates from Thomas Gleixner.
Various trivial conflict fixups in arch Kconfig due to addition of
unrelated entries nearby. And one slightly more subtle one for sparc32
(new user of GENERIC_CLOCKEVENTS), fixed up as per Thomas.
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
timekeeping: Fix a few minor newline issues.
time: remove obsolete declaration
ntp: Fix a stale comment and a few stray newlines.
ntp: Correct TAI offset during leap second
timers: Fixup the Kconfig consolidation fallout
x86: Use generic time config
unicore32: Use generic time config
um: Use generic time config
tile: Use generic time config
sparc: Use: generic time config
sh: Use generic time config
score: Use generic time config
s390: Use generic time config
openrisc: Use generic time config
powerpc: Use generic time config
mn10300: Use generic time config
mips: Use generic time config
microblaze: Use generic time config
m68k: Use generic time config
m32r: Use generic time config
...
This patch adds the BIND_CONN_TO_SESSION operation which is needed for
upcoming SP4_MACH_CRED work and useful for recovering from broken connections
without destroying the session.
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Keep track of the number of bytes read or written via buffered, direct, and
mem-mapped i/o for use by mdsthreshold size_io hints.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We only support one layout type per file system, so one threshold_item4 per
mdsthreshold4.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
- Fix mismatch between DMA mapping direction (was wrong) and DMA synchronization
direction (was correct) of isochronous reception buffers of userspace drivers
if vma-mapped for R/W access. For example, libdc1394 was affected.
- more consistent retry stategy in device discovery/ rediscovery, and improved
failure diagnostics
- various small cleanups, e.g. use SCSI layer's DMA mapping API in firewire-sbp2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=fulr
-----END PGP SIGNATURE-----
Merge tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull IEEE 1394 (FireWire) subsystem updates from Stefan Richter:
- Fix mismatch between DMA mapping direction (was wrong) and DMA
synchronization direction (was correct) of isochronous reception
buffers of userspace drivers if vma-mapped for R/W access. For
example, libdc1394 was affected.
- more consistent retry stategy in device discovery/ rediscovery, and
improved failure diagnostics
- various small cleanups, e.g. use SCSI layer's DMA mapping API in
firewire-sbp2
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: sbp2: document the absence of alignment requirements
firewire: sbp2: remove superfluous blk_queue_max_segment_size() call
firewire: sbp2: use scsi_dma_(un)map
firewire: sbp2: give correct DMA device to scsi framework
firewire: core: fw_device_refresh(): clean up error handling
firewire: core: log config rom reading errors
firewire: core: log error in case of failed bus manager lock
firewire: move rcode_string() to core
firewire: core: improve reread_config_rom() interface
firewire: core: wait for inaccessible devices after bus reset
firewire: ohci: omit spinlock IRQ flags where possible
firewire: ohci: correct signedness of a local variable
firewire: core: fix DMA mapping direction
firewire: use module_pci_driver
Pull main drm updates from Dave Airlie:
"This is the main merge window request for the drm.
It's big, but jam packed will lots of features and of course 0
regressions. (okay maybe there'll be one).
Highlights:
- new KMS drivers for server GPU chipsets: ast, mgag200 and cirrus
(qemu only). These drivers use the generic modesetting drivers.
- initial prime/dma-buf support for i915, nouveau, radeon, udl and
exynos
- switcheroo audio support: so GPUs with HDMI can turn off the sound
driver without crashing stuff.
- There are some patches drifting outside drivers/gpu into x86 and
EFI for better handling of multiple video adapters in Apple Macs,
they've got correct acks except one trivial fixup.
- Core:
edid parser has better DMT and reduced blanking support,
crtc properties,
plane properties,
- Drivers:
exynos: add 2D core accel support, prime support, hdmi features
intel: more Haswell support, initial Valleyview support, more
hdmi infoframe fixes, update MAINTAINERS for Daniel, lots of
cleanups and fixes
radeon: more HDMI audio support, improved GPU lockup recovery
support, remove nested mutexes, less memory copying on PCIE, fix
bus master enable race (kexec), improved fence handling
gma500: cleanups, 1080p support, acpi fixes
nouveau: better nva3 memory reclocking, kepler accel (needs
external firmware rip), async buffer moves on nv84+ hw.
I've some more dma-buf patches that rely on the dma-buf merge for vmap
stuff, and I've a few fixes building up, but I'd decided I'd better
get rid of the main pull sooner rather than later, so the audio guys
are also unblocked."
Fix up trivial conflict due to some duplicated changes in
drivers/gpu/drm/i915/intel_ringbuffer.c
* 'drm-core-next' of git://people.freedesktop.org/~airlied/linux: (605 commits)
drm/nouveau/nvd9: Fix GPIO initialisation sequence.
drm/nouveau: Unregister switcheroo client on exit
drm/nouveau: Check dsm on switcheroo unregister
drm/nouveau: fix a minor annoyance in an output string
drm/nouveau: turn a BUG into a WARN
drm/nv50: decode PGRAPH DATA_ERROR = 0x24
drm/nouveau/disp: fix dithering not being enabled on some eDP macbooks
drm/nvd9/copy: initialise copy engine, seems to work like nvc0
drm/nvc0/ttm: use copy engines for async buffer moves
drm/nva3/ttm: use copy engine for async buffer moves
drm/nv98/ttm: add in a (disabled) crypto engine buffer copy method
drm/nv84/ttm: use crypto engine for async buffer copies
drm/nouveau/ttm: untangle code to support accelerated buffer moves
drm/nouveau/fbcon: use fence for sync, rather than notifier
drm/nv98/crypt: non-stub implementation of the engine hooks
drm/nouveau/fifo: turn all fifo modules into engine modules
drm/nv50/graph: remove ability to do interrupt-driven context switching
drm/nv50: remove manual context unload on context destruction
drm/nv50: remove execution engine context saves on suspend
drm/nv50/fifo: use hardware channel kickoff functionality
...
Pull more networking updates from David Miller:
"Ok, everything from here on out will be bug fixes."
1) One final sync of wireless and bluetooth stuff from John Linville.
These changes have all been in his tree for more than a week, and
therefore have had the necessary -next exposure. John was just away
on a trip and didn't have a change to send the pull request until a
day or two ago.
2) Put back some defines in user exposed header file areas that were
removed during the tokenring purge. From Stephen Hemminger and Paul
Gortmaker.
3) A bug fix for UDP hash table allocation got lost in the pile due to
one of those "you got it.. no I've got it.." situations. :-)
From Tim Bird.
4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll
try to coalesce overlapping frags and crash. Fix from Eric Dumazet.
5) RCU routing table lookups can race with free_fib_info(), causing
crashes when we deref the device pointers in the route. Fix by
releasing the net device in the RCU callback. From Yanmin Zhang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits)
tcp: take care of overlaps in tcp_try_coalesce()
ipv4: fix the rcu race between free_fib_info and ip_route_output_slow
mm: add a low limit to alloc_large_system_hash
ipx: restore token ring define to include/linux/ipx.h
if: restore token ring ARP type to header
xen: do not disable netfront in dom0
phy/micrel: Fix ID of KSZ9021
mISDN: Add X-Tensions USB ISDN TA XC-525
gianfar:don't add FCB length to hard_header_len
Bluetooth: Report proper error number in disconnection
Bluetooth: Create flags for bt_sk()
Bluetooth: report the right security level in getsockopt
Bluetooth: Lock the L2CAP channel when sending
Bluetooth: Restore locking semantics when looking up L2CAP channels
Bluetooth: Fix a redundant and problematic incoming MTU check
Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
Bluetooth: Fix EIR data generation for mgmt_device_found
Bluetooth: Fix Inquiry with RSSI event mask
Bluetooth: improve readability of l2cap_seq_list code
Bluetooth: Fix skb length calculation
...
Pull user-space probe instrumentation from Ingo Molnar:
"The uprobes code originates from SystemTap and has been used for years
in Fedora and RHEL kernels. This version is much rewritten, reviews
from PeterZ, Oleg and myself shaped the end result.
This tree includes uprobes support in 'perf probe' - but SystemTap
(and other tools) can take advantage of user probe points as well.
Sample usage of uprobes via perf, for example to profile malloc()
calls without modifying user-space binaries.
First boot a new kernel with CONFIG_UPROBE_EVENT=y enabled.
If you don't know which function you want to probe you can pick one
from 'perf top' or can get a list all functions that can be probed
within libc (binaries can be specified as well):
$ perf probe -F -x /lib/libc.so.6
To probe libc's malloc():
$ perf probe -x /lib64/libc.so.6 malloc
Added new event:
probe_libc:malloc (on 0x7eac0)
You can now use it in all perf tools, such as:
perf record -e probe_libc:malloc -aR sleep 1
Make use of it to create a call graph (as the flat profile is going to
look very boring):
$ perf record -e probe_libc:malloc -gR make
[ perf record: Woken up 173 times to write data ]
[ perf record: Captured and wrote 44.190 MB perf.data (~1930712
$ perf report | less
32.03% git libc-2.15.so [.] malloc
|
--- malloc
29.49% cc1 libc-2.15.so [.] malloc
|
--- malloc
|
|--0.95%-- 0x208eb1000000000
|
|--0.63%-- htab_traverse_noresize
11.04% as libc-2.15.so [.] malloc
|
--- malloc
|
7.15% ld libc-2.15.so [.] malloc
|
--- malloc
|
5.07% sh libc-2.15.so [.] malloc
|
--- malloc
|
4.99% python-config libc-2.15.so [.] malloc
|
--- malloc
|
4.54% make libc-2.15.so [.] malloc
|
--- malloc
|
|--7.34%-- glob
| |
| |--93.18%-- 0x41588f
| |
| --6.82%-- glob
| 0x41588f
...
Or:
$ perf report -g flat | less
# Overhead Command Shared Object Symbol
# ........ ............. ............. ..........
#
32.03% git libc-2.15.so [.] malloc
27.19%
malloc
29.49% cc1 libc-2.15.so [.] malloc
24.77%
malloc
11.04% as libc-2.15.so [.] malloc
11.02%
malloc
7.15% ld libc-2.15.so [.] malloc
6.57%
malloc
...
The core uprobes design is fairly straightforward: uprobes probe
points register themselves at (inode:offset) addresses of
libraries/binaries, after which all existing (or new) vmas that map
that address will have a software breakpoint injected at that address.
vmas are COW-ed to preserve original content. The probe points are
kept in an rbtree.
If user-space executes the probed inode:offset instruction address
then an event is generated which can be recovered from the regular
perf event channels and mmap-ed ring-buffer.
Multiple probes at the same address are supported, they create a
dynamic callback list of event consumers.
The basic model is further complicated by the XOL speedup: the
original instruction that is probed is copied (in an architecture
specific fashion) and executed out of line when the probe triggers.
The XOL area is a single vma per process, with a fixed number of
entries (which limits probe execution parallelism).
The API: uprobes are installed/removed via
/sys/kernel/debug/tracing/uprobe_events, the API is integrated to
align with the kprobes interface as much as possible, but is separate
to it.
Injecting a probe point is privileged operation, which can be relaxed
by setting perf_paranoid to -1.
You can use multiple probes as well and mix them with kprobes and
regular PMU events or tracepoints, when instrumenting a task."
Fix up trivial conflicts in mm/memory.c due to previous cleanup of
unmap_single_vma().
* 'perf-uprobes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
perf probe: Detect probe target when m/x options are absent
perf probe: Provide perf interface for uprobes
tracing: Fix kconfig warning due to a typo
tracing: Provide trace events interface for uprobes
tracing: Extract out common code for kprobes/uprobes trace events
tracing: Modify is_delete, is_return from int to bool
uprobes/core: Decrement uprobe count before the pages are unmapped
uprobes/core: Make background page replacement logic account for rss_stat counters
uprobes/core: Optimize probe hits with the help of a counter
uprobes/core: Allocate XOL slots for uprobes use
uprobes/core: Handle breakpoint and singlestep exceptions
uprobes/core: Rename bkpt to swbp
uprobes/core: Make order of function parameters consistent across functions
uprobes/core: Make macro names consistent
uprobes: Update copyright notices
uprobes/core: Move insn to arch specific structure
uprobes/core: Remove uprobe_opcode_sz
uprobes/core: Make instruction tables volatile
uprobes: Move to kernel/events/
uprobes/core: Clean up, refactor and improve the code
...
Pull input layer updates from Dmitry Torokhov:
- a bunch of new drivers (DA9052/53 touchscreenn controller, Synaptics
Navpoint, LM8333 keypads, Wacom I2C touhscreen);
- updates to existing touchpad drivers (ALPS, Sntelic);
- Wacom driver now supports Intuos5;
- device-tree bindings in numerous drivers;
- other cleanups and fixes.
Fix annoying conflict in drivers/input/tablet/wacom_wac.c that I think
implies that the input layer device naming is broken, but let's see. I
brough it up with Dmitry.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
Input: matrix-keymap - fix building keymaps
Input: spear-keyboard - document DT bindings
Input: spear-keyboard - add device tree bindings
Input: matrix-keymap - wire up device tree support
Input: matrix-keymap - uninline and prepare for device tree support
Input: adp5588 - add support for gpio names
Input: omap-keypad - dynamically handle register offsets
Input: synaptics - fix compile warning
MAINTAINERS: adjust input-related patterns
Input: ALPS - switch to using input_mt_report_finger_count
Input: ALPS - add semi-MT support for v4 protocol
Input: Add Synaptics NavPoint (PXA27x SSP/SPI) driver
Input: atmel_mxt_ts - dump each message on just 1 line
Input: atmel_mxt_ts - do not read extra (checksum) byte
Input: atmel_mxt_ts - verify object size in mxt_write_object
Input: atmel_mxt_ts - only allow root to update firmware
Input: atmel_mxt_ts - use CONFIG_PM_SLEEP
Input: sentelic - report device's production serial number
Input: tl6040-vibra - Device Tree support
Input: evdev - properly handle read/write with count 0
...
Pull media updates from Mauro Carvalho Chehab:
- some V4L2 API updates needed by embedded devices
- DVB API extensions for ATSC-MH delivery system, used in US for mobile
TV
- new tuners for fc0011/0012/0013 and tua9001
- a new dvb driver for af9033/9035
- a new ATSC-MH frontend (lg2160)
- new remote controller keymaps
- Removal of a few legacy webcam driver that got replaced by gspca on
several kernel versions ago
- a new driver for Exynos 4/5 webcams(s5pp fimc-lite)
- a new webcam sensor driver (smiapp)
- a new video input driver for embedded (sta2x1xx)
- several improvements, fixes, cleanups, etc inside the drivers.
Manually fix up conflicts due to err() -> dev_err() conversion in
drivers/staging/media/easycap/easycap_main.c
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (484 commits)
[media] saa7134-cards: Remove a PCI entry added by mistake
[media] radio-sf16fmi: add support for SF16-FMD
[media] rc-loopback: remove duplicate line
[media] patch for Asus My Cinema PS3-100 (1043:48cd)
[media] au0828: Move the Kconfig knob under V4L_USB_DRIVERS
[media] em28xx: simple comment fix
[media] [resend] radio-sf16fmr2: add PnP support for SF16-FMD2
[media] smiapp: Use v4l2_ctrl_new_int_menu() instead of v4l2_ctrl_new_custom()
[media] smiapp: Add support for 8-bit uncompressed formats
[media] smiapp: Allow generic quirk registers
[media] smiapp: Use non-binning limits if the binning limit is zero
[media] smiapp: Initialise rval in smiapp_read_nvm()
[media] smiapp: Round minimum pre_pll up rather than down in ip_clk_freq check
[media] smiapp: Use 8-bit reads only before identifying the sensor
[media] smiapp: Quirk for sensors that only do 8-bit reads
[media] smiapp: Pass struct sensor to register writing commands instead of i2c_client
[media] smiapp: Allow using external clock from the clock framework
[media] zl10353: change .read_snr() to report SNR as a 0.1 dB
[media] media: add support to gspca/pac7302.c for 093a:2627 (Genius FaceCam 300)
[media] m88rs2000 - only flip bit 2 on reg 0x70 on 16th try
...
The pixel rate control is required by the OMAP3 ISP driver and should be
implemented by all media controller-compatible sensor drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
UDP stack needs a minimum hash size value for proper operation and also
uses alloc_large_system_hash() for proper NUMA distribution of its hash
tables and automatic sizing depending on available system memory.
On some low memory situations, udp_table_init() must ignore the
alloc_large_system_hash() result and reallocs a bigger memory area.
As we cannot easily free old hash table, we leak it and kmemleak can
issue a warning.
This patch adds a low limit parameter to alloc_large_system_hash() to
solve this problem.
We then specify UDP_HTABLE_SIZE_MIN for UDP/UDPLite hash table
allocation.
Reported-by: Mark Asselstine <mark.asselstine@windriver.com>
Reported-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill the no longer used task_struct->replacement_session_keyring, update
copy_creds() and exit_creds().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Smith <dsmith@redhat.com>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
After the previouse change key_replace_session_keyring() becomes a nop.
Remove the dummy definition in key.h and update the callers in
arch/*/kernel/signal.c.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Smith <dsmith@redhat.com>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Change keyctl_session_to_parent() to use task_work_add() and move
key_replace_session_keyring() logic into task_work->func().
Note that we do task_work_cancel() before task_work_add() to ensure that
only one work can be pending at any time. This is important, we must not
allow user-space to abuse the parent's ->task_works list.
The callback, replace_session_keyring(), checks PF_EXITING. I guess this
is not really needed but looks better.
As a side effect, this fixes the (unlikely) race. The callers of
key_replace_session_keyring() and keyctl_session_to_parent() lack the
necessary barriers, the parent can miss the request.
Now we can remove task_struct->replacement_session_keyring and related
code.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Smith <dsmith@redhat.com>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
exit_irq_thread() and task->irq_thread are needed to handle the unexpected
(and unlikely) exit of irq-thread.
We can use task_work instead and make this all private to
kernel/irq/manage.c, cleanup plus micro-optimization.
1. rename exit_irq_thread() to irq_thread_dtor(), make it
static, and move it up before irq_thread().
2. change irq_thread() to do task_work_add(irq_thread_dtor)
at the start and task_work_cancel() before return.
tracehook_notify_resume() can never play with kthreads,
only do_exit()->exit_task_work() can call the callback
and this is what we want.
3. remove task_struct->irq_thread and the special hook
in do_exit().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Smith <dsmith@redhat.com>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Provide a simple mechanism that allows running code in the (nonatomic)
context of the arbitrary task.
The caller does task_work_add(task, task_work) and this task executes
task_work->func() either from do_notify_resume() or from do_exit(). The
callback can rely on PF_EXITING to detect the latter case.
"struct task_work" can be embedded in another struct, still it has "void
*data" to handle the most common/simple case.
This allows us to kill the ->replacement_session_keyring hack, and
potentially this can have more users.
Performance-wise, this adds 2 "unlikely(!hlist_empty())" checks into
tracehook_notify_resume() and do_exit(). But at the same time we can
remove the "replacement_session_keyring != NULL" checks from
arch/*/signal.c and exit_creds().
Note: task_work_add/task_work_run abuses ->pi_lock. This is only because
this lock is already used by lookup_pi_state() to synchronize with
do_exit() setting PF_EXITING. Fortunately the scope of this lock in
task_work.c is really tiny, and the code is unlikely anyway.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Smith <dsmith@redhat.com>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull first series of signal handling cleanups from Al Viro:
"This is just the first part of the queue (about a half of it);
assorted fixes all over the place in signal handling.
This one ends with all sigsuspend() implementations switched to
generic one (->saved_sigmask-based).
With this, a bunch of assorted old buglets are fixed and most of the
missing bits of NOTIFY_RESUME hookup are in place. Two more fixes sit
in arm and um trees respectively, and there's a couple of broken ones
that need obvious fixes - parisc and avr32 check TIF_NOTIFY_RESUME
only on one of two codepaths; fixes for that will happen in the next
series"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (55 commits)
unicore32: if there's no handler we need to restore sigmask, syscall or no syscall
xtensa: add handling of TIF_NOTIFY_RESUME
microblaze: drop 'oldset' argument of do_notify_resume()
microblaze: handle TIF_NOTIFY_RESUME
score: add handling of NOTIFY_RESUME to do_notify_resume()
m68k: add TIF_NOTIFY_RESUME and handle it.
sparc: kill ancient comment in sparc_sigaction()
h8300: missing checks of __get_user()/__put_user() return values
frv: missing checks of __get_user()/__put_user() return values
cris: missing checks of __get_user()/__put_user() return values
powerpc: missing checks of __get_user()/__put_user() return values
sh: missing checks of __get_user()/__put_user() return values
sparc: missing checks of __get_user()/__put_user() return values
avr32: struct old_sigaction is never used
m32r: struct old_sigaction is never used
xtensa: xtensa_sigaction doesn't exist
alpha: tidy signal delivery up
score: don't open-code force_sigsegv()
cris: don't open-code force_sigsegv()
blackfin: don't open-code force_sigsegv()
...
Pull user namespace enhancements from Eric Biederman:
"This is a course correction for the user namespace, so that we can
reach an inexpensive, maintainable, and reasonably complete
implementation.
Highlights:
- Config guards make it impossible to enable the user namespace and
code that has not been converted to be user namespace safe.
- Use of the new kuid_t type ensures the if you somehow get past the
config guards the kernel will encounter type errors if you enable
user namespaces and attempt to compile in code whose permission
checks have not been updated to be user namespace safe.
- All uids from child user namespaces are mapped into the initial
user namespace before they are processed. Removing the need to add
an additional check to see if the user namespace of the compared
uids remains the same.
- With the user namespaces compiled out the performance is as good or
better than it is today.
- For most operations absolutely nothing changes performance or
operationally with the user namespace enabled.
- The worst case performance I could come up with was timing 1
billion cache cold stat operations with the user namespace code
enabled. This went from 156s to 164s on my laptop (or 156ns to
164ns per stat operation).
- (uid_t)-1 and (gid_t)-1 are reserved as an internal error value.
Most uid/gid setting system calls treat these value specially
anyway so attempting to use -1 as a uid would likely cause
entertaining failures in userspace.
- If setuid is called with a uid that can not be mapped setuid fails.
I have looked at sendmail, login, ssh and every other program I
could think of that would call setuid and they all check for and
handle the case where setuid fails.
- If stat or a similar system call is called from a context in which
we can not map a uid we lie and return overflowuid. The LFS
experience suggests not lying and returning an error code might be
better, but the historical precedent with uids is different and I
can not think of anything that would break by lying about a uid we
can't map.
- Capabilities are localized to the current user namespace making it
safe to give the initial user in a user namespace all capabilities.
My git tree covers all of the modifications needed to convert the core
kernel and enough changes to make a system bootable to runlevel 1."
Fix up trivial conflicts due to nearby independent changes in fs/stat.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
userns: Silence silly gcc warning.
cred: use correct cred accessor with regards to rcu read lock
userns: Convert the move_pages, and migrate_pages permission checks to use uid_eq
userns: Convert cgroup permission checks to use uid_eq
userns: Convert tmpfs to use kuid and kgid where appropriate
userns: Convert sysfs to use kgid/kuid where appropriate
userns: Convert sysctl permission checks to use kuid and kgids.
userns: Convert proc to use kuid/kgid where appropriate
userns: Convert ext4 to user kuid/kgid where appropriate
userns: Convert ext3 to use kuid/kgid where appropriate
userns: Convert ext2 to use kuid/kgid where appropriate.
userns: Convert devpts to use kuid/kgid where appropriate
userns: Convert binary formats to use kuid/kgid where appropriate
userns: Add negative depends on entries to avoid building code that is userns unsafe
userns: signal remove unnecessary map_cred_ns
userns: Teach inode_capable to understand inodes whose uids map to other namespaces.
userns: Fail exec for suid and sgid binaries with ids outside our user namespace.
userns: Convert stat to return values mapped from kuids and kgids
userns: Convert user specfied uids and gids in chown into kuids and kgid
userns: Use uid_eq gid_eq helpers when comparing kuids and kgids in the vfs
...
Pull the MCA deletion branch from Paul Gortmaker:
"It was good that we could support MCA machines back in the day, but
realistically, nobody is using them anymore. They were mostly limited
to 386-sx 16MHz CPU and some 486 class machines and never more than
64MB of RAM. Even the enthusiast hobbyist community seems to have
dried up close to ten years ago, based on what you can find searching
various websites dedicated to the relatively short lived hardware.
So lets remove the support relating to CONFIG_MCA. There is no point
carrying this forward, wasting cycles doing routine maintenance on it;
wasting allyesconfig build time on validating it, wasting I/O on git
grep'ping over it, and so on."
Let's see if anybody screams. It generally has compiled, and James
Bottomley pointed out that there was a MCA extension from NCR that
allowed for up to 4GB of memory and PPro-class machines. So in *theory*
there may be users out there.
But even James (technically listed as a maintainer) doesn't actually
have a system, and while Alan Cox claims to have a machine in his cellar
that he offered to anybody who wants to take it off his hands, he didn't
argue for keeping MCA support either.
So we could bring it back. But somebody had better speak up and talk
about how they have actually been using said MCA hardware with modern
kernels for us to do that. And David already took the patch to delete
all the networking driver code (commit a5e371f61ad3: "drivers/net:
delete all code/drivers depending on CONFIG_MCA").
* 'delete-mca' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MCA: delete all remaining traces of microchannel bus support.
scsi: delete the MCA specific drivers and driver code
serial: delete the MCA specific 8250 support.
arm: remove ability to select CONFIG_MCA
Main features:
- RAID10 arrays can be reshapes - adding and removing devices and
changing chunks (not 'far' array though)
- allow RAID5 arrays to be reshaped with a backup file (not tested
yet, but the priciple works fine for RAID10).
- arrays can be reshaped while a bitmap is present - you no longer
need to remove it first
- SSSE3 support for RAID6 syndrome calculations
and of course a number of minor fixes etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=q8bc
-----END PGP SIGNATURE-----
Merge tag 'md-3.5' of git://neil.brown.name/md
Pull md updates from NeilBrown:
"It's been a busy cycle for md - lots of fun stuff here.. if you like
this kind of thing :-)
Main features:
- RAID10 arrays can be reshaped - adding and removing devices and
changing chunks (not 'far' array though)
- allow RAID5 arrays to be reshaped with a backup file (not tested
yet, but the priciple works fine for RAID10).
- arrays can be reshaped while a bitmap is present - you no longer
need to remove it first
- SSSE3 support for RAID6 syndrome calculations
and of course a number of minor fixes etc."
* tag 'md-3.5' of git://neil.brown.name/md: (56 commits)
md/bitmap: record the space available for the bitmap in the superblock.
md/raid10: Remove extras after reshape to smaller number of devices.
md/raid5: improve removal of extra devices after reshape.
md: check the return of mddev_find()
MD RAID1: Further conditionalize 'fullsync'
DM RAID: Use md_error() in place of simply setting Faulty bit
DM RAID: Record and handle missing devices
DM RAID: Set recovery flags on resume
md/raid5: Allow reshape while a bitmap is present.
md/raid10: resize bitmap when required during reshape.
md: allow array to be resized while bitmap is present.
md/bitmap: make sure reshape request are reflected in superblock.
md/bitmap: add bitmap_resize function to allow bitmap resizing.
md/bitmap: use DIV_ROUND_UP instead of open-code
md/bitmap: create a 'struct bitmap_counts' substructure of 'struct bitmap'
md/bitmap: make bitmap bitops atomic.
md/bitmap: make _page_attr bitops atomic.
md/bitmap: merge bitmap_file_unmap and bitmap_file_put.
md/bitmap: remove async freeing of bitmap file.
md/bitmap: convert some spin_lock_irqsave to spin_lock_irq
...
Pull sbp-2 (firewire) target mode support from Nicholas Bellinger:
"The FireWire SBP-2 Target is a driver for using an IEEE-1394
connection as a SCSI transport. This module uses the SCSI Target
framework to expose LUNs to other machines attached to a FireWire bus,
in effect acting as a FireWire hard disk similar to FireWire Target
Disk mode on many Apple computers.
Also included are the two drivers/firewire/ patches required by
sbp-target to access fw_request fabric speed needed for mgt_agent
TCODE_WRITE_BLOCK_REQUEST ops, and exporting fw_card kref logic used
when creating/destroying active session references to individual
endpoints.
A credit goes to Chris in being able to get this code up and running
so quickly w/o any target core changes, and special thanks goes out to
Stefan Richter + Clemens Ladisch + Andy Grover for their help in
getting this driver ready for mainline. Also, one of Chris's goals
was to be able to connect sbp-target to a PowerPC based MacOS-X based
client, that he accomplished along the way in this obligatory
screenshot:
http://linux-iscsi.org/wiki/File:Linux-fireware-target-bootc-macosx.png
Great work Chris + linux-1394 team !!"
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'sbp-target-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
sbp-target: Initial merge of firewire/ieee-1394 target mode support
firewire: Move fw_card kref functions into linux/firewire.h
firewire: Add function to get speed from opaque struct fw_request
1) Ugly MSFT Hyper-V workaround in ata_piix
2) Fix a longstanding error recovery delay caused by excessive
re-re-retries, when media errors occur.
3) Minor hw-specific workarounds and quirks
4) New PATA driver for ep93xx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=CVKN
-----END PGP SIGNATURE-----
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata update from Jeff Garzik:
"Changes, all of them boring and minor:
1) Ugly MSFT Hyper-V workaround in ata_piix
2) Fix a longstanding error recovery delay caused by excessive
re-re-retries, when media errors occur.
3) Minor hw-specific workarounds and quirks
4) New PATA driver for ep93xx"
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
PATA host controller driver for ep93xx
[libata] Add " 2GB ATA Flash Disk"/"ADMA428M" to DMA blacklist
ata_generic: Skip is_intel_ider() check when ata_generic=1 is set
libata-eh don't waste time retrying media errors (v3)
ata_piix: defer disks to the Hyper-V drivers by default
libata: add a host flag to ignore detected ATA devices
New driver for INA219 and INA226, added support for IT8782F and IT8783E/F to
it87 driver, plus cleanups in a couple of drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=ZX6H
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New driver for INA219 and INA226, added support for IT8782F and
IT8783E/F to it87 driver, plus cleanups in a couple of drivers."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (it87) Make temp3 attribute conditional for IT8782F
hwmon: (it87) Convert to use devm_kzalloc and devm_request_region
hwmon: INA219 and INA226 support
hwmon: (it87) Create voltage attributes only if voltage is enabled
hwmon: (ntc_thermistor) Fix checkpatch warning
hwmon: (ntc_thermistor) Optimize and fix build warning
hwmon: (ntc_thermistor) Return error code from hwmon_device_register
hwmon: (ntc_thermistor) Convert to devm_kzalloc
hwmon: (ad7314) Remove unused defines, and rename OFFSET to SHIFT
acpi_power_meter: clean up code around setup_attrs
acpi_power_meter: drop meter_rw_attrs, use common meter_attrs
acpi_power_meter: remove duplicate code between register_{ro,rw}_attrs
acpi_power_meter: use a {RW,RO}_SENSOR_TEMPLATE macro to clean things up
acpi_power_meter: use the same struct {rw,ro}_sensor_template for both
hwmon: use module_pci_driver
hwmon: (it87) Add support for IT8782F and IT8783E/F
* Implementation of opportunistic suspend (autosleep) and user space interface
for manipulating wakeup sources.
* Hibernate updates from Bojan Smojver and Minho Ban.
* Updates of the runtime PM core and generic PM domains framework related to
PM QoS.
* Assorted fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=Q2vo
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
- Implementation of opportunistic suspend (autosleep) and user space
interface for manipulating wakeup sources.
- Hibernate updates from Bojan Smojver and Minho Ban.
- Updates of the runtime PM core and generic PM domains framework
related to PM QoS.
- Assorted fixes.
* tag 'pm-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (25 commits)
epoll: Fix user space breakage related to EPOLLWAKEUP
PM / Domains: Make it possible to add devices to inactive domains
PM / Hibernate: Use get_gendisk to verify partition if resume_file is integer format
PM / Domains: Fix computation of maximum domain off time
PM / Domains: Fix link checking when add subdomain
PM / Sleep: User space wakeup sources garbage collector Kconfig option
PM / Sleep: Make the limit of user space wakeup sources configurable
PM / Documentation: suspend-and-cpuhotplug.txt: Fix typo
PM / Domains: Cache device stop and domain power off governor results, v3
PM / Domains: Make device removal more straightforward
PM / Sleep: Fix a mistake in a conditional in autosleep_store()
epoll: Add a flag, EPOLLWAKEUP, to prevent suspend while epoll events are ready
PM / QoS: Create device constraints objects on notifier registration
PM / Runtime: Remove device fields related to suspend time, v2
PM / Domains: Rework default domain power off governor function, v2
PM / Domains: Rework default device stop governor function, v2
PM / Sleep: Add user space interface for manipulating wakeup sources, v3
PM / Sleep: Add "prevent autosleep time" statistics to wakeup sources
PM / Sleep: Implement opportunistic sleep, v2
PM / Sleep: Add wakeup_source_activate and wakeup_source_deactivate tracepoints
...
As Heinz-Juergen Oertel pointed out 'CAN error frames' are a already defined
term for the CAN protocol violation indication on the wire.
To avoid confusion with the error messages created by CAN drivers available
via CAN RAW sockets update the documentation and change the naming from
'error frames' to 'error messages' or 'error message frames'.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is the first big chunk for 3.5 merges of sound stuff.
There are a few big changes in different areas. First off, the
streaming logic of USB-audio endpoints has been largely rewritten
for the better support of "implicit feedback". If anything about USB
got broken, this change has to be checked.
For HD-audio, the resume procedure was changed; instead of delaying
the resume of the hardware until the first use, now waking up immediately
at resume. This is for buggy BIOS.
For ASoC, dynamic PCM support and the improved support for digital links
between off-SoC devices are major framework changes.
Some highlights are below:
* HD-audio
- Avoid the accesses of invalid pin-control bits that may stall the codec
- V-ref setup cleanups
- Fix the races in power-saving code
- Fix the races in codec cache hashes and connection lists
- Split some common codes for BIOS auto-parser to hda_auto_parser.c
- Changed the PM resume code to wake up immediately for buggy BIOS
- Creative SoundCore3D support
- Add Conexant CX20751/2/3/4 codec support
* ASoC
- Dynamic PCM support, allowing support for SoCs with internal routing
through components with tight sequencing and formatting constraints
within their internal paths or where there are multiple components
connected with CPU managed DMA controllers inside the SoC.
- Greatly improved support for direct digital links between off-SoC
devices, providing a much simpler way of connecting things like digital
basebands to CODECs.
- Much more fine grained and robust locking, cleaning up some of the
confusion that crept in with multi-component.
- CPU support for nVidia Tegra 30 I2S and audio hub controllers and
ST-Ericsson MSP I2S controolers
- New CODEC drivers for Cirrus CS42L52, LAPIS Semiconductor ML26124, Texas
Instruments LM49453.
- Some regmap changes needed by the Tegra I2S driver.
- mc13783 audio support.
* Misc
- Rewrite with module_pci_driver()
- Xonar DGX support for snd-oxygen
- Improvement of packet handling in snd-firewire driver
- New USB-endpoint streaming logic
- Enhanced M-audio FTU quirks and relevant cleanups
- Increment the support of OSS devices to 256
- snd-aloop accuracy improvement
There are a few more pending changes for 3.5, but they will be
sent slightly later as partly depending on the changes of DRM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=+JSm
-----END PGP SIGNATURE-----
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This is the first big chunk for 3.5 merges of sound stuff.
There are a few big changes in different areas. First off, the
streaming logic of USB-audio endpoints has been largely rewritten for
the better support of "implicit feedback". If anything about USB got
broken, this change has to be checked.
For HD-audio, the resume procedure was changed; instead of delaying
the resume of the hardware until the first use, now waking up
immediately at resume. This is for buggy BIOS.
For ASoC, dynamic PCM support and the improved support for digital
links between off-SoC devices are major framework changes.
Some highlights are below:
* HD-audio
- Avoid accesses of invalid pin-control bits that may stall the codec
- V-ref setup cleanups
- Fix the races in power-saving code
- Fix the races in codec cache hashes and connection lists
- Split some common codes for BIOS auto-parser to hda_auto_parser.c
- Changed the PM resume code to wake up immediately for buggy BIOS
- Creative SoundCore3D support
- Add Conexant CX20751/2/3/4 codec support
* ASoC
- Dynamic PCM support, allowing support for SoCs with internal
routing through components with tight sequencing and formatting
constraints within their internal paths or where there are multiple
components connected with CPU managed DMA controllers inside the
SoC.
- Greatly improved support for direct digital links between off-SoC
devices, providing a much simpler way of connecting things like
digital basebands to CODECs.
- Much more fine grained and robust locking, cleaning up some of the
confusion that crept in with multi-component.
- CPU support for nVidia Tegra 30 I2S and audio hub controllers and
ST-Ericsson MSP I2S controolers
- New CODEC drivers for Cirrus CS42L52, LAPIS Semiconductor ML26124,
Texas Instruments LM49453.
- Some regmap changes needed by the Tegra I2S driver.
- mc13783 audio support.
* Misc
- Rewrite with module_pci_driver()
- Xonar DGX support for snd-oxygen
- Improvement of packet handling in snd-firewire driver
- New USB-endpoint streaming logic
- Enhanced M-audio FTU quirks and relevant cleanups
- Increment the support of OSS devices to 256
- snd-aloop accuracy improvement
There are a few more pending changes for 3.5, but they will be sent
slightly later as partly depending on the changes of DRM."
Fix up conflicts in regmap (due to duplicate patches, with some further
updates then having already come in from the regmap tree). Also some
fairly trivial context conflicts in the imx and mcx soc drivers.
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (280 commits)
ALSA: snd-usb: fix stream info output in /proc
ALSA: pcm - Add proper state checks to snd_pcm_drain()
ALSA: sh: Fix up namespace collision in sh_dac_audio.
ALSA: hda/realtek - Fix unused variable compile warning
ASoC: sh: fsi: enable chip specific data transfer mode
ASoC: sh: fsi: call fsi_hw_startup/shutdown from fsi_dai_trigger()
ASoC: sh: fsi: use same format for IN/OUT
ASoC: sh: fsi: add fsi_version() and removed meaningless version check
ASoC: sh: fsi: use register field macro name on IN/OUT_DMAC
ASoC: tegra: Add machine driver for WM8753 codec
ALSA: hda - Fix possible races of accesses to connection list array
ASoC: OMAP: HDMI: Introduce codec
ARM: mx31_3ds: Add sound support
ASoC: imx-mc13783 cleanup
mx31moboard: Add sound support
ASoC: mc13783 codec cleanups
ASoC: add imx-mc13783 sound support
ASoC: Add mc13783 codec
mfd: mc13xxx: add codec platform data
ASoC: don't flip master of DT-instantiated DAI links
...
Pull perf fixes from Ingo Molnar:
- Leftover AMD PMU driver fix fix from the end of the v3.4
stabilization cycle.
- Late tools/perf/ changes that missed the first round:
* endianness fixes
* event parsing improvements
* libtraceevent fixes factored out from trace-cmd
* perl scripting engine fixes related to libtraceevent,
* testcase improvements
* perf inject / pipe mode fixes
* plus a kernel side fix
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Update event scheduling constraints for AMD family 15h models
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "sched, perf: Use a single callback into the scheduler"
perf evlist: Show event attribute details
perf tools: Bump default sample freq to 4 kHz
perf buildid-list: Work better with pipe mode
perf tools: Fix piped mode read code
perf inject: Fix broken perf inject -b
perf tools: rename HEADER_TRACE_INFO to HEADER_TRACING_DATA
perf tools: Add union u64_swap type for swapping u64 data
perf tools: Carry perf_event_attr bitfield throught different endians
perf record: Fix documentation for branch stack sampling
perf target: Add cpu flag to sample_type if target has cpu
perf tools: Always try to build libtraceevent
perf tools: Rename libparsevent to libtraceevent in Makefile
perf script: Rename struct event to struct event_format in perl engine
perf script: Explicitly handle known default print arg type
perf tools: Add hardcoded name term for pmu events
perf tools: Separate 'mem:' event scanner bits
perf tools: Use allocated list for each parsed event
perf tools: Add support for displaying event parser debug info
perf test: Move parse event automated tests to separated object
Pull x86 platform changes from Ingo Molnar:
"This tree includes assorted platform driver updates and a preparatory
series for a platform with custom DMA remapping semantics (sta2x11 I/O
hub)."
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vsmp: Fix number of CPUs when vsmp is disabled
keyboard: Use BIOS Keyboard variable to set Numlock
x86/olpc/xo1/sci: Report RTC wakeup events
x86/olpc/xo1/sci: Produce wakeup events for buttons and switches
x86, platform: Initial support for sta2x11 I/O hub
x86: Introduce CONFIG_X86_DMA_REMAP
x86-32: Introduce CONFIG_X86_DEV_DMA_OPS
Commit 211ed86510
"net: delete all instances of special processing for token ring"
removed the define for IPX_FRAME_TR_8022.
While it is unlikely, we can't be 100% sure that there aren't
random userspace consumers of this value, so restore it.
The only instance I could find was in ncpfs-2.2.6, and it was
safe as-is, since it used #ifdef IPX_FRAME_TR_8022 around the
two use cases it had, but there may be other userspace packages
without similar ifdefs.
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull UML updates from Richard Weinberger:
"Most changes are bug fixes and cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: missing checks of __put_user()/__get_user() return values
um: stub_rt_sigsuspend isn't needed these days anymore
um/x86: merge (and trim) 32- and 64-bit variants of ptrace.h
irq: Remove irq_chip->release()
um: Remove CONFIG_IRQ_RELEASE_METHOD
um: Remove usage of irq_chip->release()
um: Implement um_free_irq()
um: Fix __swp_type()
um: Implement a custom pte_same() function
um: Add BUG() to do_ops()'s error path
um: Remove unused variables
um: bury unused _TIF_RESTORE_SIGMASK
um: wrong sigmask saved in case of multiple sigframes
um: add TIF_NOTIFY_RESUME
um: ->restart_block.fn needs to be reset on sigreturn
- New CPUs: SH7734 (SH-4A), SH7264 and SH7269 (SH-2A)
- New boards: RSK2+SH7264, RSK2+SH7269
- Unbreaking kgdb for SMP
- Consolidation of _32/_64 page fault handling.
- watchdog and legacy DMA chainsawing, part 1
- Conversion to evt2irq() hwirq lookup, to support relocation
of vectored IRQs for irqdomains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAk+7gb4ACgkQGkmNcg7/o7hoPQCgvdQGi9dk3ewIBX9LQ9mL6L81
ls8An3PMKi9fHANnztVUAheP1U2DEanJ
=v/VS
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH updates from Paul Mundt:
- New CPUs: SH7734 (SH-4A), SH7264 and SH7269 (SH-2A)
- New boards: RSK2+SH7264, RSK2+SH7269
- Unbreaking kgdb for SMP
- Consolidation of _32/_64 page fault handling.
- watchdog and legacy DMA chainsawing, part 1
- Conversion to evt2irq() hwirq lookup, to support relocation of
vectored IRQs for irqdomains.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (98 commits)
sh: intc: Kill off special reservation interface.
sh: Enable PIO API for hp6xx and se770x.
sh: Kill off machvec IRQ hinting.
sh: dma: More legacy cpu dma chainsawing.
sh: Kill off MAX_DMA_ADDRESS leftovers.
sh: Tidy up some of the cpu legacy dma header mess.
sh: Move sh4a dma header from cpu-sh4 to cpu-sh4a.
sh64: Fix up vmalloc fault range check.
Revert "sh: Ensure fixmap and store queue space can co-exist."
serial: sh-sci: Fix for port types without BRI interrupts.
sh: legacy PCI evt2irq migration.
sh: cpu dma evt2irq migration.
sh: sh7763rdp evt2irq migration.
sh: sdk7780 evt2irq migration.
sh: migor evt2irq migration.
sh: landisk evt2irq migration.
sh: kfr2r09 evt2irq migration.
sh: ecovec24 evt2irq migration.
sh: ap325rxa evt2irq migration.
sh: urquell evt2irq migration.
...
This reverts commit cb04ff9ac4 ("sched, perf: Use a single
callback into the scheduler").
Before this change was introduced, the process switch worked
like this (wrt. to perf event schedule):
schedule (prev, next)
- schedule out all perf events for prev
- switch to next
- schedule in all perf events for current (next)
After the commit, the process switch looks like:
schedule (prev, next)
- schedule out all perf events for prev
- schedule in all perf events for (next)
- switch to next
The problem is, that after we schedule perf events in, the pmu
is enabled and we can receive events even before we make the
switch to next - so "current" still being prev process (event
SAMPLE data are filled based on the value of the "current"
process).
Thats exactly what we see for test__PERF_RECORD test. We receive
SAMPLES with PID of the process that our tracee is scheduled
from.
Discussed with Peter Zijlstra:
> Bah!, yeah I guess reverting is the right thing for now. Sad
> though.
>
> So by having the two hooks we have a black-spot between them
> where we receive no events at all, this black-spot covers the
> hand-over of current and we thus don't receive the 'wrong'
> events.
>
> I rather liked we could do away with both that black-spot and
> clean up the code a little, but apparently people rely on it.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: acme@redhat.com
Cc: paulus@samba.org
Cc: cjashfor@linux.vnet.ibm.com
Cc: fweisbec@gmail.com
Cc: eranian@google.com
Link: http://lkml.kernel.org/r/20120523111302.GC1638@m.brq.redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Without it we get:
drivers/mfd/max77693.c: In function ‘max77693_i2c_probe’:
drivers/mfd/max77693.c:157:2: error: implicit declaration of function
‘max77693_irq_init’ [-Werror=implicit-function-declaration]
drivers/mfd/max77693.c: In function ‘max77693_resume’:
drivers/mfd/max77693.c:215:2: error: implicit declaration of function
‘max77693_irq_resume’ [-Werror=implicit-function-declaration]
drivers/mfd/max77693-irq.c: In function ‘max77693_irq_lock’:
drivers/mfd/max77693-irq.c:104:2: error: ‘struct max77693_dev’ has no member
named ‘irqlock’
drivers/mfd/max77693-irq.c: In function ‘max77693_irq_sync_unlock’:
drivers/mfd/max77693-irq.c:119:11: error: ‘struct max77693_dev’ has no member
named ‘irq_masks_cache’
drivers/mfd/max77693-irq.c:119:42: error: ‘struct max77693_dev’ has no member
named ‘irq_masks_cur’
drivers/mfd/max77693-irq.c:122:13: error: ‘struct max77693_dev’ has no member
named ‘irq_masks_cur’
drivers/mfd/max77693-irq.c:125:24: error: ‘struct max77693_dev’ has no member
named ‘irqlock’
drivers/mfd/max77693-irq.c: In function ‘max77693_irq_mask’:
drivers/mfd/max77693-irq.c:141:11: error: ‘struct max77693_dev’ has no member
named ‘irq_masks_cur’
drivers/mfd/max77693-irq.c:143:11: error: ‘struct max77693_dev’ has no member
named ‘irq_masks_cur’
drivers/mfd/max77693-irq.c: In function ‘max77693_irq_unmask’:
drivers/mfd/max77693-irq.c:153:11: error: ‘struct max77693_dev’ has no member
named ‘irq_masks_cur’
drivers/mfd/max77693-irq.c:155:11: error: ‘struct max77693_dev’ has no member
named ‘irq_masks_cur’
drivers/mfd/max77693-irq.c: In function ‘max77693_irq_thread’:
drivers/mfd/max77693-irq.c:209:26: error: ‘struct max77693_dev’ has no member
named ‘irq_masks_cur’
drivers/mfd/max77693-irq.c:211:27: error: ‘struct max77693_dev’ has no member
named ‘irq_masks_cur’
drivers/mfd/max77693-irq.c:217:39: error: ‘struct max77693_dev’ has no member
named ‘irq_domain’
drivers/mfd/max77693-irq.c: In function ‘max77693_irq_init’:
drivers/mfd/max77693-irq.c:260:2: error: ‘struct max77693_dev’ has no member
named ‘irqlock’
drivers/mfd/max77693-irq.c:268:12: error: ‘struct max77693_dev’ has no member
named ‘irq_masks_cur’
drivers/mfd/max77693-irq.c:269:12: error: ‘struct max77693_dev’ has no member
named ‘irq_masks_cache’
drivers/mfd/max77693-irq.c:271:12: error: ‘struct max77693_dev’ has no member
named ‘irq_masks_cur’
drivers/mfd/max77693-irq.c:272:12: error: ‘struct max77693_dev’ has no member
named ‘irq_masks_cache’
drivers/mfd/max77693-irq.c:292:10: error: ‘struct max77693_dev’ has no member
named ‘irq_domain’
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds the ability for ttm common code to take an SG table
and use it as the backing for a slave TTM object.
The drivers can then populate their GTT tables using the SG object.
v2: make sure to setup VM for sg bos as well.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
the ttm drivers need this currently, in order to get fault handling
working and efficient.
It also allows addrs to be NULL for devices like udl.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch has the SW FCoE driver and the bnx2fc
driver make use of the new fcoe_sysfs API added
earlier in this patch series.
After this patch a fcoe_ctlr_device is allocated with
private data in this order.
+------------------+ +------------------+
| fcoe_ctlr_device | | fcoe_ctlr_device |
+------------------+ +------------------+
| fcoe_ctlr | | fcoe_ctlr |
+------------------+ +------------------+
| fcoe_interface | | bnx2fc_interface |
+------------------+ +------------------+
libfcoe also takes part in this new model since it
discovers and manages fcoe_fcf instances. The memory
allocation is different for FCFs. I didn't want to
impact libfcoe's fcoe_fcf processing, so this patch
creates fcoe_fcf_device instances for each discovered
fcoe_fcf. The two are paired using a (void * priv)
member of the fcoe_ctlr_device. This allows libfcoe
to continue maintaining its list of fcoe_fcf instances
and simply attaches and detaches them from existing
or new fcoe_fcf_device instances.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds a 'fcoe bus' infrastructure to the kernel
that is driven by changes to libfcoe which allow LLDs to
present FIP (FCoE Initialization Protocol) discovered
entities and their attributes to user space via sysfs.
This patch adds the following APIs-
fcoe_ctlr_device_add
fcoe_ctlr_device_delete
fcoe_fcf_device_add
fcoe_fcf_device_delete
They allow the LLD to expose the FCoE ENode Controller
and any discovered FCFs (Fibre Channel Forwarders, e.g.
FCoE switches) to the user. Each of these new devices
has their own bus_type so that they are grouped together
for easy lookup from a user space application. Each
new class has an attribute_group to expose attributes
for any created instances. The attributes are-
fcoe_ctlr_device
* fcf_dev_loss_tmo
* lesb_link_fail
* lesb_vlink_fail
* lesb_miss_fka
* lesb_symb_err
* lesb_err_block
* lesb_fcs_error
fcoe_fcf_device
* fabric_name
* switch_name
* priority
* selected
* fc_map
* vfid
* mac
* fka_peroid
* fabric_state
* dev_loss_tmo
A device loss infrastructre similar to the FC Transport's
is also added by this patch. It is nice to have so that a
link flapping adapter doesn't continually advance the count
used to identify the discovered FCF. FCFs will exist in a
"Disconnected" state until either the timer expires or the
FCF is rediscovered and becomes "Connected."
This patch generates a few checkpatch.pl WARNINGS that
I'm not sure what to do about. They're macros modeled
around the FC Transport attribute building macros, which
have the same 'feature' where the caller can ommit a cast
in the argument list and no cast occurs in the code. I'm
not sure how to keep the code condensed while keeping the
macros. Any advice would be appreciated.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently the fcoe_ctlr associated with an interface is allocated
as a member of struct fcoe_interface. This causes problems when
attempting to use the new fcoe_sysfs APIs which allow us to allocate
the fcoe_interface as private data to the fcoe_ctlr_device instance.
The problem is that libfcoe wants to be able use pointer math to find a
fcoe_ctlr's fcoe_ctlr_device as well as finding a fcoe_ctlr_device's
assocated fcoe_ctlr. To do this we need to allocate the
fcoe_ctlr_device, with private data for the LLD. The private data
contains the fcoe_ctlr and its private data is the fcoe_interface.
This patch only allocates the fcoe_interface with the fcoe_ctlr, the
fcoe_ctlr_device will be added in a later patch, which will complete
the below diagram-
+------------------+
| fcoe_ctlr_device |
+------------------+
| fcoe_ctlr |
+------------------+
| fcoe_interface |
+------------------+
This prep work will allow us to go from a fcoe_ctlr_device instance
to its fcoe_ctlr as well as from a fcoe_ctlr to its fcoe_ctlr_device
once the fcoe_sysfs API is in use (later patches in this series).
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Define flags and allocate space in on-disk journal structures to support
checksumming of journal metadata.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This set includes some minor fixes and improvements.
The one large patch addresses the special "nodir" mode,
which has been a long neglected proof of concept, but
with these fixes seems to be quite usable. It allows
the resource master to be assigned statically instead of
dynamically, which can improve performance if there is
little locality and most resources are shared.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mHOh
-----END PGP SIGNATURE-----
Merge tag 'dlm-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm
Pull dlm updates from David Teigland:
"This set includes some minor fixes and improvements. The one large
patch addresses the special "nodir" mode, which has been a long
neglected proof of concept, but with these fixes seems to be quite
usable. It allows the resource master to be assigned statically
instead of dynamically, which can improve performance if there is
little locality and most resources are shared."
* tag 'dlm-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
dlm: NULL dereference on failure in kmem_cache_create()
gfs2: fix recovery during unmount
dlm: fixes for nodir mode
dlm: improve error and debug messages
dlm: avoid unnecessary search in search_rsb
dlm: limit rcom debug messages
dlm: fix waiter recovery
dlm: prevent connections during shutdown
* Always support xattrs (remove the Kconfig option)
* Always support debugging (remove the Kconfig option)
* A fix for a memory leak on error path
* A number of clean-ups
UBI:
* Always support debugging (remove the Kconfig option)
* Remove "data type" hint support
* Huge amount of renames to prepare for the fastmap wor
* A lot of clean-ups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=+6Qi
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.5-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI and UBIFS updates from Artem Bityutskiy:
UBIFS:
* Always support xattrs (remove the Kconfig option)
* Always support debugging (remove the Kconfig option)
* A fix for a memory leak on error path
* A number of clean-ups
UBI:
* Always support debugging (remove the Kconfig option)
* Remove "data type" hint support
* Huge amount of renames to prepare for the fastmap wor
* A lot of clean-ups
* tag 'upstream-3.5-rc1' of git://git.infradead.org/linux-ubifs: (54 commits)
UBI: modify ubi_wl_flush function to clear work queue for a lnum
UBI: introduce UBI_ALL constant
UBI: add lnum and vol_id to struct ubi_work
UBI: add volume id struct ubi_ainf_peb
UBI: add in hex the value for UBI_INTERNAL_VOL_START to comment
UBI: rename scan.c to attach.c
UBI: remove scan.h
UBI: rename UBI_SCAN_UNKNOWN_EC
UBI: move and rename attach_by_scanning
UBI: rename _init_scan functions
UBI: amend comments after all the renamings
UBI: rename ubi_scan_leb_slab
UBI: rename ubi_scan_move_to_list
UBI: rename ubi_scan_destroy_ai
UBI: rename ubi_scan_get_free_peb
UBI: rename ubi_scan_rm_volume
UBI: rename ubi_scan_find_av
UBI: rename ubi_scan_add_used
UBI: remove unused function
UBI: make ubi_scan_erase_peb static and rename
...
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
Pull HID subsystem updates from Jiri Kosina:
"Apart from various driver updates and added support for a number of
new devices (mostly multitouch ones, but not limited to), there is one
change that is worth pointing out explicitly: creation of HID device
groups and proper autoloading of hid-multitouch, implemented by Henrik
Rydberg."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (50 commits)
HID: wacom: fix build breakage without CONFIG_LEDS_CLASS
HID: waltop: Extend barrel button fix
HID: hyperv: Set the hid drvdata correctly
HID: wacom: Unify speed setting
HID: wacom: Add speed setting for Intuos4 WL
HID: wacom: Move Graphire raport header check.
HID: uclogic: Add support for UC-Logic TWHL850
HID: explain the signed/unsigned handling in hid_add_field()
HID: handle logical min/max signedness properly in parser
HID: logitech: read all 32 bits of report type bitfield
HID: wacom: Add LED selector control for Wacom Intuos4 WL
HID: hid-multitouch: fix wrong protocol detection
HID: wiimote: Fix IR data parser
HID: wacom: Add tilt reporting for Intuos4 WL
HID: multitouch: MT interface matching for Baanto
HID: hid-multitouch: Only match MT interfaces
HID: Create a common generic driver
HID: hid-multitouch: Switch to device groups
HID: Create a generic device group
HID: Allow bus wildcard matching
...
Pull scheduler changes from Ingo Molnar:
"The biggest change is the cleanup/simplification of the load-balancer:
instead of the current practice of architectures twiddling scheduler
internal data structures and providing the scheduler domains in
colorfully inconsistent ways, we now have generic scheduler code in
kernel/sched/core.c:sched_init_numa() that looks at the architecture's
node_distance() parameters and (while not fully trusting it) deducts a
NUMA topology from it.
This inevitably changes balancing behavior - hopefully for the better.
There are various smaller optimizations, cleanups and fixlets as well"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Taint kernel with TAINT_WARN after sleep-in-atomic bug
sched: Remove stale power aware scheduling remnants and dysfunctional knobs
sched/debug: Fix printing large integers on 32-bit platforms
sched/fair: Improve the ->group_imb logic
sched/nohz: Fix rq->cpu_load[] calculations
sched/numa: Don't scale the imbalance
sched/fair: Revert sched-domain iteration breakage
sched/x86: Rewrite set_cpu_sibling_map()
sched/numa: Fix the new NUMA topology bits
sched/numa: Rewrite the CONFIG_NUMA sched domain support
sched/fair: Propagate 'struct lb_env' usage into find_busiest_group
sched/fair: Add some serialization to the sched_domain load-balance walk
sched/fair: Let minimally loaded cpu balance the group
sched: Change rq->nr_running to unsigned int
x86/numa: Check for nonsensical topologies on real hw as well
x86/numa: Hard partition cpu topology masks on node boundaries
x86/numa: Allow specifying node_distance() for numa=fake
x86/sched: Make mwait_usable() heed to "idle=" kernel parameters properly
sched: Update documentation and comments
sched_rt: Avoid unnecessary dequeue and enqueue of pushable tasks in set_cpus_allowed_rt()
Pull perf changes from Ingo Molnar:
"Lots of changes:
- (much) improved assembly annotation support in perf report, with
jump visualization, searching, navigation, visual output
improvements and more.
- kernel support for AMD IBS PMU hardware features. Notably 'perf
record -e cycles:p' and 'perf top -e cycles:p' should work without
skid now, like PEBS does on the Intel side, because it takes
advantage of IBS transparently.
- the libtracevents library: it is the first step towards unifying
tracing tooling and perf, and it also gives a tracing library for
external tools like powertop to rely on.
- infrastructure: various improvements and refactoring of the UI
modules and related code
- infrastructure: cleanup and simplification of the profiling
targets code (--uid, --pid, --tid, --cpu, --all-cpus, etc.)
- tons of robustness fixes all around
- various ftrace updates: speedups, cleanups, robustness
improvements.
- typing 'make' in tools/ will now give you a menu of projects to
build and a short help text to explain what each does.
- ... and lots of other changes I forgot to list.
The perf record make bzImage + perf report regression you reported
should be fixed."
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (166 commits)
tracing: Remove kernel_lock annotations
tracing: Fix initial buffer_size_kb state
ring-buffer: Merge separate resize loops
perf evsel: Create events initially disabled -- again
perf tools: Split term type into value type and term type
perf hists: Fix callchain ip printf format
perf target: Add uses_mmap field
ftrace: Remove selecting FRAME_POINTER with FUNCTION_TRACER
ftrace/x86: Have x86 ftrace use the ftrace_modify_all_code()
ftrace: Make ftrace_modify_all_code() global for archs to use
ftrace: Return record ip addr for ftrace_location()
ftrace: Consolidate ftrace_location() and ftrace_text_reserved()
ftrace: Speed up search by skipping pages by address
ftrace: Remove extra helper functions
ftrace: Sort all function addresses, not just per page
tracing: change CPU ring buffer state from tracing_cpumask
tracing: Check return value of tracing_dentry_percpu()
ring-buffer: Reset head page before running self test
ring-buffer: Add integrity check at end of iter read
ring-buffer: Make addition of pages in ring buffer atomic
...
Pull cgroup updates from Tejun Heo:
"cgroup file type addition / removal is updated so that file types are
added and removed instead of individual files so that dynamic file
type addition / removal can be implemented by cgroup and used by
controllers. blkio controller changes which will come through block
tree are dependent on this. Other changes include res_counter cleanup
and disallowing kthread / PF_THREAD_BOUND threads to be attached to
non-root cgroups.
There's a reported bug with the file type addition / removal handling
which can lead to oops on cgroup umount. The issue is being looked
into. It shouldn't cause problems for most setups and isn't a
security concern."
Fix up trivial conflict in Documentation/feature-removal-schedule.txt
* 'for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (21 commits)
res_counter: Account max_usage when calling res_counter_charge_nofail()
res_counter: Merge res_counter_charge and res_counter_charge_nofail
cgroups: disallow attaching kthreadd or PF_THREAD_BOUND threads
cgroup: remove cgroup_subsys->populate()
cgroup: get rid of populate for memcg
cgroup: pass struct mem_cgroup instead of struct cgroup to socket memcg
cgroup: make css->refcnt clearing on cgroup removal optional
cgroup: use negative bias on css->refcnt to block css_tryget()
cgroup: implement cgroup_rm_cftypes()
cgroup: introduce struct cfent
cgroup: relocate __d_cgrp() and __d_cft()
cgroup: remove cgroup_add_file[s]()
cgroup: convert memcg controller to the new cftype interface
memcg: always create memsw files if CONFIG_CGROUP_MEM_RES_CTLR_SWAP
cgroup: convert all non-memcg controllers to the new cftype interface
cgroup: relocate cftype and cgroup_subsys definitions in controllers
cgroup: merge cft_release_agent cftype array into the base files array
cgroup: implement cgroup_add_cftypes() and friends
cgroup: build list of all cgroups under a given cgroupfs_root
cgroup: move cgroup_clear_directory() call out of cgroup_populate_dir()
...
Pull percpu updates from Tejun Heo:
"Contains Alex Shi's three patches to remove percpu_xxx() which overlap
with this_cpu_xxx(). There shouldn't be any functional change."
* 'for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: remove percpu_xxx() functions
x86: replace percpu_xxx funcs with this_cpu_xxx
net: replace percpu_xxx funcs with this_cpu_xxx or __this_cpu_xxx
Pull workqueue changes from Tejun Heo:
"Nothing exciting. Most are updates to debug stuff and related fixes.
Two not-too-critical bugs are fixed - WARN_ON() triggering spurious
during cpu offlining and unlikely lockdep related oops."
* 'for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
lockdep: fix oops in processing workqueue
workqueue: skip nr_running sanity check in worker_enter_idle() if trustee is active
workqueue: Catch more locking problems with flush_work()
workqueue: change BUG_ON() to WARN_ON()
trace: Remove unused workqueue tracer
Here is the big staging tree pull request for the 3.5-rc1 merge window.
Loads of changes here, and we just narrowly added more lines than we
added:
622 files changed, 28356 insertions(+), 26059 deletions(-)
But, good news is that there is a number of subsystems that moved out of
the staging tree, to their respective "real" portions of the kernel.
Code that moved out was:
- iio core code
- mei driver
- vme core and bridge drivers
There was one broken network driver that moved into staging as a step
before it is removed from the tree (pc300), and there was a few new
drivers added to the tree:
- new iio drivers
- gdm72xx wimax USB driver
- ipack subsystem and 2 drivers
All of the movements around have acks from the various subsystem
maintainers, and all of this has been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7q8MACgkQMUfUDdst+ymjogCguo8fANFVlPWeZGeoBTL+aQfQ
yTkAoLE0codmh+2SvhulYgyU1Wh6ZDK2
=nJ2F
-----END PGP SIGNATURE-----
Merge tag 'staging-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree changes from Greg Kroah-Hartman:
"Here is the big staging tree pull request for the 3.5-rc1 merge
window.
Loads of changes here, and we just narrowly added more lines than we
added:
622 files changed, 28356 insertions(+), 26059 deletions(-)
But, good news is that there is a number of subsystems that moved out
of the staging tree, to their respective "real" portions of the
kernel.
Code that moved out was:
- iio core code
- mei driver
- vme core and bridge drivers
There was one broken network driver that moved into staging as a step
before it is removed from the tree (pc300), and there was a few new
drivers added to the tree:
- new iio drivers
- gdm72xx wimax USB driver
- ipack subsystem and 2 drivers
All of the movements around have acks from the various subsystem
maintainers, and all of this has been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up various trivial conflicts, along with a non-trivial one found
in -next and pointed out by Olof Johanssen: a clean - but incorrect -
merge of the arch/arm/boot/dts/at91sam9g20.dtsi file. Fix up manually
as per Stephen Rothwell.
* tag 'staging-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (536 commits)
Staging: bcm: Remove two unused variables from Adapter.h
Staging: bcm: Removes the volatile type definition from Adapter.h
Staging: bcm: Rename all "INT" to "int" in Adapter.h
Staging: bcm: Fix warning: __packed vs. __attribute__((packed)) in Adapter.h
Staging: bcm: Correctly format all comments in Adapter.h
Staging: bcm: Fix all whitespace issues in Adapter.h
Staging: bcm: Properly format braces in Adapter.h
Staging: ipack/bridges/tpci200: remove unneeded casts
Staging: ipack/bridges/tpci200: remove TPCI200_SHORTNAME constant
Staging: ipack: remove board_name and bus_name fields from struct ipack_device
Staging: ipack: improve the register of a bus and a device in the bus.
staging: comedi: cleanup all the comedi_driver 'detach' functions
staging: comedi: remove all 'default N' in Kconfig
staging: line6/config.h: Delete unused header
staging: gdm72xx depends on NET
staging: gdm72xx: Set up parent link in sysfs for gdm72xx devices
staging: drm/omap: initial dmabuf/prime import support
staging: drm/omap: dmabuf/prime mmap support
pstore/ram: Add ECC support
pstore/ram: Switch to persistent_ram routines
...
Here's the big TTY/serial driver pull request for the 3.5-rc1 merge window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7rBoACgkQMUfUDdst+ykXsgCfeDKx6ZgLidYy3H40Y2Pt3XEO
TicAn1fcdGwOmMR/mowa+kTA68D/J6i2
=S7tG
-----END PGP SIGNATURE-----
Merge tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY updates from Greg Kroah-Hartman:
"Here's the big TTY/serial driver pull request for the 3.5-rc1 merge
window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (115 commits)
serial: bfin_uart: Make MMR access compatible with 32 bits bf609 style controller.
serial: bfin_uart: RTS and CTS MMRs can be either 16-bit width or 32-bit width.
serial: bfin_uart: narrow the reboot condition in DMA tx interrupt
serial: bfin_uart: Adapt bf5xx serial driver to bf60x serial4 controller.
Revert "serial_core: Update buffer overrun statistics."
tty: hvc_xen: NULL dereference on allocation failure
tty: Fix LED error return
tty: Allow uart_register/unregister/register
tty: move global ldisc idle waitqueue to the individual ldisc
serial8250-em: Add DT support
serial8250-em: clk_get() IS_ERR() error handling fix
serial_core: Update buffer overrun statistics.
tty: drop the pty lock during hangup
cris: fix missing tty arg in wait_event_interruptible_tty call
tty/amiserial: Add missing argument for tty_unlock()
tty_lock: Localise the lock
pty: Lock the devpts bits privately
tty_lock: undo the old tty_lock use on the ctty
serial8250-em: Emma Mobile UART driver V2
Add missing call to uart_update_timeout()
...
Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging switch
driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7q28ACgkQMUfUDdst+ykXmwCfcPASzC+/bDkuqdWsqzxlWZ7+
VOQAnAriySv397St36J6Hz5bMQZwB1Yq
=SQc+
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging
switch driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up conflicts in drivers/extcon/extcon-max8997.c where git noticed
that a patch to the deleted drivers/misc/max8997-muic.c driver needs to
be applied to this one.
* tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (90 commits)
uio_pdrv_genirq: get irq through platform resource if not set otherwise
memory: tegra{20,30}-mc: Remove empty *_remove()
printk() - isolate KERN_CONT users from ordinary complete lines
sysfs: get rid of some lockdep false positives
Drivers: hv: util: Properly handle version negotiations.
Drivers: hv: Get rid of an unnecessary check in vmbus_prep_negotiate_resp()
memory: tegra{20,30}-mc: Use dev_err_ratelimited()
driver core: Add dev_*_ratelimited() family
Driver Core: don't oops with unregistered driver in driver_find_device()
printk() - restore prefix/timestamp printing for multi-newline strings
printk: add stub for prepend_timestamp()
ARM: tegra30: Make MC optional in Kconfig
ARM: tegra20: Make MC optional in Kconfig
ARM: tegra30: MC: Remove unnecessary BUG*()
ARM: tegra20: MC: Remove unnecessary BUG*()
printk: correctly align __log_buf
ARM: tegra30: Add Tegra Memory Controller(MC) driver
ARM: tegra20: Add Tegra Memory Controller(MC) driver
printk() - restore timestamp printing at console output
printk() - do not merge continuation lines of different threads
...
Here are a few various char/misc tree patches for the 3.5-rc1 merge window.
Nothing major here at all, just different driver updates and some parport dead
code removal.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7qxoACgkQMUfUDdst+ynz0gCggUMf6y60T1rPVT7h2Ab3iy5k
9d0An0U607GRDK1e5lwbZdGuuRkfBwRi
=NpES
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Char/Misc patches from Greg Kroah-Hartman:
"Here are a few various char/misc tree patches for the 3.5-rc1 merge
window.
Nothing major here at all, just different driver updates and some
parport dead code removal.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
parport: remove unused dead code from lowlevel drivers
xilinx_hwicap: reset XHI_MAX_RETRIES
xilinx_hwicap: add support for virtex6 FPGAs
Support M95040 SPI EEPROM
misc: add support for bmp18x chips to the bmp085 driver
misc: bmp085: add device tree properties
misc: clean up bmp085 driver
misc: do not mark exported functions __devexit
misc: add missing __devexit_p() annotations
pch_phub: delete duplicate definitions
misc: Fix irq leak in max8997_muic_probe error path
Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.
It's touches a lot of different parts of the kernel, all USB drivers,
due to some API cleanups (getting rid of the ancient err() macro) and
some changes that are needed for USB 3.0 power management updates.
There are also lots of new drivers, pimarily gadget, but others as well.
We deleted a staging driver, which was nice, and finally dropped the
obsolete usbfs code, which will make Al happy to never have to touch
that again.
There were some build errors in the tree that linux-next found a few
days ago, but those were fixed by the most recent changes (all were due
to us not building with CONFIG_PM disabled.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7qs0ACgkQMUfUDdst+ymjOgCfeoWqWk1bsKKt6SZULvQois5i
3csAn1Uapcm8Uswwpnj2v1/2Zh4rBHLA
=4jM1
-----END PGP SIGNATURE-----
Merge tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB 3.5-rc1 changes from Greg Kroah-Hartman:
"Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.
It's touches a lot of different parts of the kernel, all USB drivers,
due to some API cleanups (getting rid of the ancient err() macro) and
some changes that are needed for USB 3.0 power management updates.
There are also lots of new drivers, pimarily gadget, but others as
well. We deleted a staging driver, which was nice, and finally
dropped the obsolete usbfs code, which will make Al happy to never
have to touch that again.
There were some build errors in the tree that linux-next found a few
days ago, but those were fixed by the most recent changes (all were
due to us not building with CONFIG_PM disabled.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (477 commits)
xhci: Fix DIV_ROUND_UP compile error.
xhci: Fix compile with CONFIG_USB_SUSPEND=n
USB: Fix core compile with CONFIG_USB_SUSPEND=n
brcm80211: Fix compile error for .disable_hub_initiated_lpm.
Revert "USB: EHCI: work around bug in the Philips ISP1562 controller"
MAINTAINERS: Add myself as maintainer to the USB PHY Layer
USB: EHCI: fix command register configuration lost problem
USB: Remove races in devio.c
USB: ehci-platform: remove update_device
USB: Disable hub-initiated LPM for comms devices.
xhci: Add Intel U1/U2 timeout policy.
xhci: Add infrastructure for host-specific LPM policies.
USB: Add macros for interrupt endpoint types.
xhci: Reserve one command for USB3 LPM disable.
xhci: Some Evaluate Context commands must succeed.
USB: Disable USB 3.0 LPM in critical sections.
USB: Add support to enable/disable USB3 link states.
USB: Allow drivers to disable hub-initiated LPM.
USB: Calculate USB 3.0 exit latencies for LPM.
USB: Refactor code to set LPM support flag.
...
Conflicts:
arch/arm/mach-exynos/mach-nuri.c
arch/arm/mach-exynos/mach-universal_c210.c
drivers/net/wireless/ath/ath6kl/usb.c
Save the allocated memory to store the parsed device node information
to the global device structure so that sub devices can directly use this
pointer.
In this way, the sub devices does not require to re-allocate the
memory for storing the sub-devices specific device node information.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add resistor-select parameter to the platform data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Recent removal of Token Ring breaks the build of iproute2.
Even though Token Ring support is gone from the kernel, it is worth
keeping the the definition of the TR ARP type to avoid breaking
userspace programs that use this file.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save the server major and minor ID results from EXCHANGE_ID, as they
are needed for detecting server trunking.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
"noresvport" and "discrtry" can be passed to nfs_create_rpc_client()
by setting flags in the passed-in nfs_client. This change makes it
easy to add new flags.
Note that these settings are now "sticky" over the lifetime of a
struct nfs_client, and may even be copied when an nfs_client is
cloned.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean up: Continue to rationalize the locking in nfs_get_client() by
moving the logic that handles the case where a matching server IP
address is not found.
When we support server trunking detection, client initialization may
return a different nfs_client struct than was passed to it. Change
the synopsis of the init_client methods to return an nfs_client.
The client initialization logic in nfs_get_client() is not much more
than a wrapper around ->init_client. It's simpler to keep the little
bits of error handling in the version-specific init_client methods.
No behavior change is expected.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currently our NFS client assigns a unique SETCLIENTID boot verifier
for each server IP address it knows about. It's set to CURRENT_TIME
when the struct nfs_client for that server IP is created.
During the SETCLIENTID operation, our client also presents an
nfs_client_id4 string to servers, as an identifier on which the server
can hang all of this client's NFSv4 state. Our client's
nfs_client_id4 string is unique for each server IP address.
An NFSv4 server is obligated to wipe all NFSv4 state associated with
an nfs_client_id4 string when the client presents the same
nfs_client_id4 string along with a changed SETCLIENTID boot verifier.
When our client unmounts the last of a server's shares, it destroys
that server's struct nfs_client. The next time the client mounts that
NFS server, it creates a fresh struct nfs_client with a fresh boot
verifier. On seeing the fresh verifer, the server wipes any previous
NFSv4 state associated with that nfs_client_id4.
However, NFSv4.1 clients are supposed to present the same
nfs_client_id4 string to all servers. And, to support Transparent
State Migration, the same nfs_client_id4 string should be presented
to all NFSv4.0 servers so they recognize that migrated state for this
client belongs with state a server may already have for this client.
(This is known as the Uniform Client String model).
If the nfs_client_id4 string is the same but the boot verifier changes
for each server IP address, SETCLIENTID and EXCHANGE_ID operations
from such a client could unintentionally result in a server wiping a
client's previously obtained lease.
Thus, if our NFS client is going to use a fixed nfs_client_id4 string,
either for NFSv4.0 or NFSv4.1 mounts, our NFS client should use a
boot verifier that does not change depending on server IP address.
Replace our current per-nfs_client boot verifier with a per-nfs_net
boot verifier.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean up: When naming fields and data types, follow established
conventions to facilitate accurate grep/cscope searches.
Introduced by commit e50a7a1a "NFS: make NFS client allocated per
network namespace context," Tue Jan 10, 2012.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean up: When naming fields and data types, follow established
conventions to facilitate accurate grep/cscope searches.
Additionally, for consistency, move the impl_id field into the NFSv4-
specific part of the nfs_client, and free that memory in the logic
that shuts down NFSv4 nfs_clients.
Introduced by commit 7d2ed9ac "NFSv4: parse and display server
implementation ids," Fri Feb 17, 2012.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Clean up: When naming fields and data types, follow established
conventions to facilitate accurate grep/cscope searches.
Additionally, for consistency, move the scope field into the NFSv4-
specific part of the nfs_client, and free that memory in the logic
that shuts down NFSv4 nfs_clients.
Introduced by commit 99fe60d0 "nfs41: exchange_id operation", April
1 2009.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
fs/nfs/nfs4state.c does not yet have any dprintk() call sites, and I'm
about to introduce some. We will need a new flag for enabling them.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
While we generally attempt to get rid of board specific files and replace
them with device tree based descriptions, a lot of platforms have not
come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination of
DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wkmj
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc board specific changes from Olof Johansson:
"While we generally attempt to get rid of board specific files and
replace them with device tree based descriptions, a lot of platforms
have not come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination
of DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones."
Fix up trivial conflicts in arch/arm/mach-{mmp/ttc_dkb.c,shmobile/{Kconfig,Makefile}}
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: shmobile: fix smp build
ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
kirkwood: Add iconnect support
orion/kirkwood: create a generic function for gpio led blinking
kirkwood/orion: fix orion_gpio_set_blink
ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
kirkwood: Allow nand to be configured via. devicetree
mtd: Add orion_nand devicetree bindings
ARM: kirkwood: Basic support for DNS-320 and DNS-325
ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva
ARM: mach-shmobile: Use DT_MACHINE for KZM9G
ARM: pxa: hx4700: Add Synaptics NavPoint touchpad
ARM: pxa: Use REGULATOR_SUPPLY macro
ARM: mach-shmobile: kzm9g: enable SMP boot
ARM: mach-shmobile: kzm9g: defconfig update
ARM: mach-shmobile: kzm9g: add PCF8757 gpio-key
ARM: mach-shmobile: kzm9g: add SDHI support
ARM: mach-shmobile: kzm9g: add MMCIF support
ARM: mach-shmobile: kzm9g: correct screen direction
ARM: mach-shmobile: sh73a0.h: add GPIO_NR
...
John says:
--------------------
I apologize for not having sent this sooner. FWIW, I was in a car
somewhere between Illinois and North Carolina for most of the day
Sunday and Monday... :-)
This is (obviously) the last non-fix pull request for wireless bits
intended for 3.5. It includes AP support for mwifiex, a variety of HCI
and other updates for NFC, some brcmfmac and brcmsmac refactoring,
a large batch of ssb and bcma updates, a batch of ath6kl updates,
some cfg80211 and mac80211 updates/refactoring from Johannes Berg,
a rather large collection of Bluetooth updates by way of Gustavo,
and a variety of other bits here and there.
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
Right ID of KSZ9021 is 0x00221610.
Because lower 4bit is a revision number, it varies according to a chip.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
Three new system-on-chip models are supported: the st-ericsson u9540
in ux500, the sam9n12 in at91 and the emma ev2 in shmobile.
Emma is a little bit special because it is completely unrelated to
the classic shmobile models, but the new Renesas rmobile SoCs are a
combination of things from both Emma and shmobile, so it was decided to
have them all live in one directory.
This also contains updates to existing shmobile soc code as well as some
related board changes due to dependencies.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=5TAz
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull support for new arm SoCs from Olof Johansson:
"Three new system-on-chip models are supported: the st-ericsson u9540
in ux500, the sam9n12 in at91 and the emma ev2 in shmobile.
Emma is a little bit special because it is completely unrelated to the
classic shmobile models, but the new Renesas rmobile SoCs are a
combination of things from both Emma and shmobile, so it was decided
to have them all live in one directory.
This also contains updates to existing shmobile soc code as well as
some related board changes due to dependencies."
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
mach-shmobile: Use DT_MACHINE for KZM9D V3
mach-shmobile: Emma Mobile EV2 DT support V3
mach-shmobile: KZM9D board Ethernet support V3
mach-shmobile: Emma Mobile EV2 GPIO support V3
mach-shmobile: Emma Mobile EV2 SMP support V3
mach-shmobile: KZM9D board support V3
mach-shmobile: Emma Mobile EV2 SoC base support V3
gpio: Emma Mobile GPIO driver V2
ARM: mach-shmobile: sh73a0: fixup PINT/IRQ16-IRQ31 irq number conflict
ARM: mach-shmobile: clock-r8a7740: use followparent_recalc on usb24s
ARM: mach-shmobile: clock-r8a7740: add MMCIF clock
ARM: mach-shmobile: clock-r8a7740: add SDHI clock
ARM: mach-shmobile: clock-r8a7740: add USB clock
ARM: mach-shmobile: clock-r8a7740: add FSI clock
ARM: mach-shmobile: r8a7740: cleanup I2C workaround method
ARM: mach-shmobile: r8a7740: add gpio_irq support
ARM: mach-shmobile: sh7372: Add FSI DMAEngine support
ARM / mach-shmobile: Use preset_lpj with calibrate_delay()
ARM: ux500: ioremap differences for DB9540
ARM: ux500: core U9540 support
...
The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game of
booting using device trees, which is a great step forward for them. at91
and spear have pretty much completed this process with a huge amount of
work being put into at91. The other platforms are continuing the process.
We finally start to see the payback on this investment, as new machines
are getting supported purely by adding a .dts source file that can be
completely independent of the kernel source.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7DYv
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull device tree conversions for arm-soc, part 1, from Olof Johansson:
"The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game
of booting using device trees, which is a great step forward for them.
at91 and spear have pretty much completed this process with a huge
amount of work being put into at91. The other platforms are
continuing the process.
We finally start to see the payback on this investment, as new
machines are getting supported purely by adding a .dts source file
that can be completely independent of the kernel source."
Fix up trivial conflict in arch/arm/Kconfig
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: at91: Add ADC driver to at91sam9260/at91sam9g20 dtsi files
arm/dts: omap4-panda: Add LEDs support
arm/dts: omap4-sdp: Add LEDs support
arm/dts: twl4030: Add twl4030-gpio node
OMAP4: devices: Do not create mcpdm device if the dtb has been provided
OMAP4: devices: Do not create dmic device if the dtb has been provided
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
ARM: ux500: Enable PRCMU Timer 4 (clocksource) for Device Tree
ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
ARM: ux500: Fork cpu-db8500 platform_devs for sequential DT enablement
ARM: ux500: Do not attempt to register non-existent i2c devices on Snowball
ARM: SPEAr3xx: Correct keyboard data passed from DT
...
These cleanups are basically all over the place. The idea is to collect
changes with minimal impact but large number of changes so we can avoid
them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Hcjs
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
Sometimes a single IOMMU user may have to deal with several
different IOMMU devices (e.g. remoteproc).
When an IOMMU fault happens, such users have to regain their
context in order to deal with the fault.
Users can't use the private fields of neither the iommu_domain nor
the IOMMU device, because those are already used by the IOMMU core
and low level driver (respectively).
This patch just simply allows users to pass a private token (most
notably their own context pointer) to iommu_set_fault_handler(),
and then makes sure it is provided back to the users whenever
an IOMMU fault happens.
The patch also adopts remoteproc to the new fault handling
interface, but the real functionality using this (recovery of
remote processors) will only be added later in a subsequent patch
set.
Cc: Fernando Guzman Lugo <fernando.lugo@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Add support for the Texas Instruments INA219 and INA226 power monitors.
Signed-off-by: Lothar Felten <l-felten@ti.com>
[guenter.roeck@ericsson.com: formatting cleanup; check for smbus word data;
select PGA=8 for INA219]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
At present reserving the IRLs in the IRQ bitmap in addition to the
dropping of the legacy IRQ pre-allocation prevent IRL IRQs from being
allocated for the x3proto board.
The only reason to permit reservations was to lock down possible hardware
vectors prior to dynamic IRQ scanning, but this doesn't matter much given
that the hardware controller configuration is sorted before we get around
to doing any dynamic IRQ allocation anyways. Beyond that, all of the
tables are __init annotated, so quite a bit more work would need to be
done to support reconfiguring things like IRL controllers on the fly,
much more than would ever make it worth the hassle.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The omapdrm driver uses this for setting per-overlay rotation. It
is likely also useful for setting YUV->RGB colorspace conversion
matrix, etc.
Signed-off-by: Rob Clark <rob@ti.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A bitmask property is similar to an enum. The enum value is a bit
position (0-63), and valid property values consist of a mask of
zero or more of (1 << enum_val[n]).
[airlied: 1LL -> 1ULL]
Signed-off-by: Rob Clark <rob@ti.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'exynos-drm-next' of git://git.infradead.org/users/kmpark/linux-samsung:
drm/exynos: add G2D driver
drm/exynos: added vp scaling feature for hdmi
drm/exynos: added source size to overlay structure
drm/exynos: add additional display mode for hdmi
drm/exynos: enable dvi mode for dvi monitor
drm/exynos: fixed wrong pageflip finish event for interlace mode
drm/exynos: add PM functions for hdmi and mixer
drm/exynos: add dpms for hdmi
drm/exynos: use threaded irq for hdmi hotplug
drm/exynos: use platform_get_irq_byname for hdmi
drm/exynos: cleanup for hdmi platform data
drm/exynos: added a feature to get gem buffer information.
drm/exynos: added drm prime feature.
drm/exynos: added cache attribute support for gem.
vgaarb: Provide dummy default device functions
The DRM mode config functions structure declared by drivers and pointed
to by the drm_mode_config funcs field is never modified. Make it a const
pointer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Rob Clark <rob.clark@linaro.org>
Reviwed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The GEM vm operations structure is passed to the VM core that stores it
in a const field. There vm operations structures can thus be const in
DRM as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Rob Clark <rob.clark@linaro.org>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Low four bits are downstream port count. High bit indicates peer OUI
support. OUI matching will allow us to do additional per-sink handling
for things like DP->VGA bandwidth limits or (hopefully) the iMac-as-
display hack.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
DisplayPort has an escape hatch by which sources and sinks can identify
each other. We would prefer not to notice this, but I suspect we're
going to need to.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
TILER is a block in OMAP4's DMM which lets DSS fetch frames in a rotated manner.
Physical memory can be mapped to a portion of OMAP's system address space called
TILER address space. The TILER address space is split into 8 views. Each view
represents a rotated or mirrored form of the mapped physical memory. When a
DISPC overlay's base address is programmed to one of these views, the TILER
fetches the pixels according to the orientation of the view. A view is further
split into 4 containers, each container holds elements of a particular size.
Rotation can be achieved at the granularity of elements in the container. For
more information on TILER, refer to the Memory Subsytem section in OMAP4 TRM.
Rotation type TILER has been added which is used to exploit the capabilities of
these 8 views for performing various rotations.
When fetching from addresses mapped to TILER space, the DISPC DMA can fetch
pixels in either 1D or 2D bursts. The fetch depends on which TILER container we
are accessing. Accessing 8, 16 and 32 bit sized containers requires 2D bursts,
and page mode sized containers require 1D bursts.
The DSS2 user is expected to provide the Tiler address of the view that it is
interested in. This is passed to the paddr and p_uv_addr parameters in
omap_overlay_info. It is also expected to provide the stride value based on the
view's orientation and container type, this should be passed to the screen_width
parameter of omap_overlay_info. In calc_tiler_rotation_offset screen_width is
used to calculate the required row_inc for DISPC. x_predecim and y_predecim are
also used to calculate row_inc and pix_inc thereby adding predecimation support
for TILER.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add SSSE3 optimized recovery functions, as well as a system
for selecting the most appropriate recovery functions to use.
Originally-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Jim Kukunas <james.t.kukunas@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
guts of saved_sigmask-based sigsuspend/rt_sigsuspend. Takes
kernel sigset_t *.
Open-coded instances replaced with calling it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull core irq changes from Ingo Molnar:
"A collection of small fixes."
By Thomas Gleixner
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hexagon: Remove select of not longer existing Kconfig switches
arm: Select core options instead of redefining them
genirq: Do not consider disabled wakeup irqs
genirq: Allow check_wakeup_irqs to notice level-triggered interrupts
genirq: Be more informative on irq type mismatch
genirq: Reject bogus threaded irq requests
genirq: Streamline irq_action
Pull security subsystem updates from James Morris:
"New notable features:
- The seccomp work from Will Drewry
- PR_{GET,SET}_NO_NEW_PRIVS from Andy Lutomirski
- Longer security labels for Smack from Casey Schaufler
- Additional ptrace restriction modes for Yama by Kees Cook"
Fix up trivial context conflicts in arch/x86/Kconfig and include/linux/filter.h
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (65 commits)
apparmor: fix long path failure due to disconnected path
apparmor: fix profile lookup for unconfined
ima: fix filename hint to reflect script interpreter name
KEYS: Don't check for NULL key pointer in key_validate()
Smack: allow for significantly longer Smack labels v4
gfp flags for security_inode_alloc()?
Smack: recursive tramsmute
Yama: replace capable() with ns_capable()
TOMOYO: Accept manager programs which do not start with / .
KEYS: Add invalidation support
KEYS: Do LRU discard in full keyrings
KEYS: Permit in-place link replacement in keyring list
KEYS: Perform RCU synchronisation on keys prior to key destruction
KEYS: Announce key type (un)registration
KEYS: Reorganise keys Makefile
KEYS: Move the key config into security/keys/Kconfig
KEYS: Use the compat keyctl() syscall wrapper on Sparc64 for Sparc32 compat
Yama: remove an unused variable
samples/seccomp: fix dependencies on arch macros
Yama: add additional ptrace scopes
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Kj9v
-----END PGP SIGNATURE-----
Merge tag 'virtio-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus
Pull virtio updates from Rusty Russell.
* tag 'virtio-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio: fix typo in comment
virtio-mmio: Devices parameter parsing
virtio_blk: Drop unused request tracking list
virtio-blk: Fix hot-unplug race in remove method
virtio: Use ida to allocate virtio index
virtio: balloon: separate out common code between remove and freeze functions
virtio: balloon: drop restore_common()
9p: disconnect channel when PCI device is removed
virtio: update documentation to v0.9.5 of spec
- Delete "@request_vqs" and "@free_vqs" comments, since
they are no longer in struct virtio_config_ops.
- According to the macro below, "@val" should be "@v".
Signed-off-by: Chen Baozi <chenbaozi@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pull smp hotplug cleanups from Thomas Gleixner:
"This series is merily a cleanup of code copied around in arch/* and
not changing any of the real cpu hotplug horrors yet. I wish I'd had
something more substantial for 3.5, but I underestimated the lurking
horror..."
Fix up trivial conflicts in arch/{arm,sparc,x86}/Kconfig and
arch/sparc/include/asm/thread_info_32.h
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
um: Remove leftover declaration of alloc_task_struct_node()
task_allocator: Use config switches instead of magic defines
sparc: Use common threadinfo allocator
score: Use common threadinfo allocator
sh-use-common-threadinfo-allocator
mn10300: Use common threadinfo allocator
powerpc: Use common threadinfo allocator
mips: Use common threadinfo allocator
hexagon: Use common threadinfo allocator
m32r: Use common threadinfo allocator
frv: Use common threadinfo allocator
cris: Use common threadinfo allocator
x86: Use common threadinfo allocator
c6x: Use common threadinfo allocator
fork: Provide kmemcache based thread_info allocator
tile: Use common threadinfo allocator
fork: Provide weak arch_release_[task_struct|thread_info] functions
fork: Move thread info gfp flags to header
fork: Remove the weak insanity
sh: Remove cpu_idle_wait()
...
Pull RCU changes from Ingo Molnar:
"This is the v3.5 RCU tree from Paul E. McKenney:
1) A set of improvements and fixes to the RCU_FAST_NO_HZ feature (with
more on the way for 3.6). Posted to LKML:
https://lkml.org/lkml/2012/4/23/324 (commits 1-3 and 5),
https://lkml.org/lkml/2012/4/16/611 (commit 4),
https://lkml.org/lkml/2012/4/30/390 (commit 6), and
https://lkml.org/lkml/2012/5/4/410 (commit 7, combined with
the other commits for the convenience of the tester).
2) Changes to make rcu_barrier() avoid disrupting execution of CPUs
that have no RCU callbacks. Posted to LKML:
https://lkml.org/lkml/2012/4/23/322.
3) A couple of commits that improve the efficiency of the interaction
between preemptible RCU and the scheduler, these two being all that
survived an abortive attempt to allow preemptible RCU's
__rcu_read_lock() to be inlined. The full set was posted to LKML at
https://lkml.org/lkml/2012/4/14/143, and the first and third patches
of that set remain.
4) Lai Jiangshan's algorithmic implementation of SRCU, which includes
call_srcu() and srcu_barrier(). A major feature of this new
implementation is that synchronize_srcu() no longer disturbs the
execution of other CPUs. This work is based on earlier
implementations by Peter Zijlstra and Paul E. McKenney. Posted to
LKML: https://lkml.org/lkml/2012/2/22/82.
5) A number of miscellaneous bug fixes and improvements which were
posted to LKML at: https://lkml.org/lkml/2012/4/23/353 with
subsequent updates posted to LKML."
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
rcu: Make rcu_barrier() less disruptive
rcu: Explicitly initialize RCU_FAST_NO_HZ per-CPU variables
rcu: Make RCU_FAST_NO_HZ handle timer migration
rcu: Update RCU maintainership
rcu: Make exit_rcu() more precise and consolidate
rcu: Move PREEMPT_RCU preemption to switch_to() invocation
rcu: Ensure that RCU_FAST_NO_HZ timers expire on correct CPU
rcu: Add rcutorture test for call_srcu()
rcu: Implement per-domain single-threaded call_srcu() state machine
rcu: Use single value to handle expedited SRCU grace periods
rcu: Improve srcu_readers_active_idx()'s cache locality
rcu: Remove unused srcu_barrier()
rcu: Implement a variant of Peter's SRCU algorithm
rcu: Improve SRCU's wait_idx() comments
rcu: Flip ->completed only once per SRCU grace period
rcu: Increment upper bit only for srcu_read_lock()
rcu: Remove fast check path from __synchronize_srcu()
rcu: Direct algorithmic SRCU implementation
rcu: Introduce rcutorture testing for rcu_barrier()
timer: Fix mod_timer_pinned() header comment
...
Pull iommu core changes from Ingo Molnar:
"The IOMMU changes in this cycle are mostly about factoring out
Intel-VT-d specific IRQ remapping details and introducing struct
irq_remap_ops, in preparation for AMD specific hardware."
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
iommu: Fix off by one in dmar_get_fault_reason()
irq_remap: Fix the 'sub_handle' uninitialized warning
irq_remap: Fix UP build failure
irq_remap: Fix compiler warning with CONFIG_IRQ_REMAP=y
iommu: rename intr_remapping.[ch] to irq_remapping.[ch]
iommu: rename intr_remapping references to irq_remapping
x86, iommu/vt-d: Clean up interfaces for interrupt remapping
iommu/vt-d: Convert MSI remapping setup to remap_ops
iommu/vt-d: Convert free_irte into a remap_ops callback
iommu/vt-d: Convert IR set_affinity function to remap_ops
iommu/vt-d: Convert IR ioapic-setup to use remap_ops
iommu/vt-d: Convert missing apic.c intr-remapping call to remap_ops
iommu/vt-d: Make intr-remapping initialization generic
iommu: Rename intr_remapping files to intel_intr_remapping
These are all new code, they've been in -next already so should be OK
for merge this time round. I'd been planning to send a pull request
today after they'd had a bit of exposure there to make sure breakage
didn't propagate into your tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5L34
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Last minute updates
These are all new code, they've been in -next already so should be OK
for merge this time round. I'd been planning to send a pull request
today after they'd had a bit of exposure there to make sure breakage
didn't propagate into your tree.
- Add ocrdma hardware driver for Emulex IB-over-Ethernet adapters
- Add generic and mlx4 support for "raw" QPs: allow suitably privileged
applications to send and receive arbitrary packets directly to/from
the hardware
- Add "doorbell drop" handling to the cxgb4 driver
- A fairly large batch of qib hardware driver changes
- A few fixes for lockdep-detected issues
- A few other miscellaneous fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yWfr
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- Add ocrdma hardware driver for Emulex IB-over-Ethernet adapters
- Add generic and mlx4 support for "raw" QPs: allow suitably privileged
applications to send and receive arbitrary packets directly to/from
the hardware
- Add "doorbell drop" handling to the cxgb4 driver
- A fairly large batch of qib hardware driver changes
- A few fixes for lockdep-detected issues
- A few other miscellaneous fixes and cleanups
Fix up trivial conflict in drivers/net/ethernet/emulex/benet/be.h.
* tag 'rdma-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (53 commits)
RDMA/cxgb4: Include vmalloc.h for vmalloc and vfree
IB/mlx4: Fix mlx4_ib_add() error flow
IB/core: Fix IB_SA_COMP_MASK macro
IB/iser: Fix error flow in iser ep connection establishment
IB/mlx4: Increase the number of vectors (EQs) available for ULPs
RDMA/cxgb4: Add query_qp support
RDMA/cxgb4: Remove kfifo usage
RDMA/cxgb4: Use vmalloc() for debugfs QP dump
RDMA/cxgb4: DB Drop Recovery for RDMA and LLD queues
RDMA/cxgb4: Disable interrupts in c4iw_ev_dispatch()
RDMA/cxgb4: Add DB Overflow Avoidance
RDMA/cxgb4: Add debugfs RDMA memory stats
cxgb4: DB Drop Recovery for RDMA and LLD queues
cxgb4: Common platform specific changes for DB Drop Recovery
cxgb4: Detect DB FULL events and notify RDMA ULD
RDMA/cxgb4: Drop peer_abort when no endpoint found
RDMA/cxgb4: Always wake up waiters in c4iw_peer_abort_intr()
mlx4_core: Change bitmap allocator to work in round-robin fashion
RDMA/nes: Don't call event handler if pointer is NULL
RDMA/nes: Fix for the ORD value of the connecting peer
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPuiSaAAoJEDeqqVYsXL0MJ8wH/2QYwxCtTzwgBE4DSUrZ/mnO
ygiiausG7gNY845hAmXhoEqhYBe1GA/fvfSXOdurAPrFmfu2HvvPEyKmu3soWxLM
rrXP7JNRjHOSz+GIktZECg6K9iobldl0zCxdn515ATnBEOZVom5v+uBE13sfg5uP
iOS73JF7h2VRcAYuw8jsVTdc/rnH2nG4TsbW2B+Hp3Ti1pFSnyHbbNuE2FJ9bEX4
gTBtsYYRZPWl24WuhmmS6LHyGqL+rcU/wKj4+rAdNQwsh+MBgcMDhGQ1UWg/3OGN
N8wur7AEQnyvsYdufjFNmHBux4TcdCVZISsWYb3frctJ5XVtYViMjlbmMMy1T7s=
=rxQP
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI misc update from James Bottomley:
"The patch contains the usual assortment of driver updates (be2iscsi,
bfa, bnx2i, fcoe, hpsa, isci, lpfc, megaraid, mpt2sas, pm8001, sg)
plus an assortment of other changes and fixes. Also new is the fact
that the isci update is delivered as a git merge (with signed tag)."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (158 commits)
isci: End the RNC resumption wait when the RNC is destroyed.
isci: Fixed RNC bug that lost the suspension or resumption during destroy
isci: Fix RNC AWAIT_SUSPENSION->INVALIDATING transition.
isci: Manage the IREQ_NO_AUTO_FREE_TAG under scic_lock.
isci: Remove obviated host callback list.
isci: Check IDEV_GONE before performing abort path operations.
isci: Restore the ATAPI device RNC management code.
isci: Don't wait for an RNC suspend if it's being destroyed.
isci: Change the phy control and link reset interface for HW reasons.
isci: Added timeouts to RNC suspensions in the abort path.
isci: Add protocol indicator for TMF requests.
isci: Directly control IREQ_ABORT_PATH_ACTIVE when completing TMFs.
isci: Wait for RNC resumption before leaving the abort path.
isci: Fix RNC suspend call for SCI_RESUMING state.
isci: Manage tag releases differently when aborting tasks.
isci: Callbacks to libsas occur under scic_lock and are synchronized.
isci: When in the abort path, defeat other resume calls until done.
isci: Implement waiting for suspend in the abort path.
isci: Make sure all TCs are terminated and cleaned in LUN reset.
isci: Manage the LLHANG timer enable/disable per-device.
...
Pull scsi-target changes from Nicholas Bellinger:
"There has been lots of work in existing code in a number of areas this
past cycle. The major highlights have been:
* Removal of transport_do_task_sg_chain() from core + fabrics
(Roland)
* target-core: Removal of se_task abstraction from target-core and
enforce hw_max_sectors for pSCSI backends (hch)
* Re-factoring of iscsi-target tx immediate/response queues (agrover)
* Conversion of iscsi-target back to using target core memory
allocation logic (agrover)
We've had one last minute iscsi-target patch go into for-next to
address a nasty regression bug related to the target core allocation
logic conversion from agrover that is not included in friday's
linux-next build, but has been included in this series.
On the new fabric module code front for-3.5, here is a brief status
update for the three currently in flight this round:
* usb-gadget target driver:
Sebastian Siewior's driver for supporting usb-gadget target mode
operation. This will be going out as a separate PULL request from
target-pending/usb-target-merge with subsystem maintainer ACKs. There
is one minor target-core patch in this series required to function.
* sbp ieee-1394/firewire target driver:
Chris Boot's driver for supportting the Serial Block Protocol (SBP)
across IEEE-1394 Firewire hardware. This will be going out as a
separate PULL request from target-pending/sbp-target-merge with two
additional drivers/firewire/ patches w/ subsystem maintainer ACKs.
* qla2xxx LLD target mode infrastructure changes + tcm_qla2xxx:
The Qlogic >= 24xx series HW target mode LLD infrastructure patch-set
and tcm_qla2xxx fabric driver. Support for FC target mode using
qla2xxx LLD code has been officially submitted by Qlogic to James
below, and is currently outstanding but not yet merged into
scsi.git/for-next..
[PATCH 00/22] qla2xxx: Updates for scsi "misc" branch
http://www.spinics.net/lists/linux-scsi/msg59350.html
Note there are *zero* direct dependencies upon this for-next series
for the qla2xxx LLD target + tcm_qla2xxx patches submitted above, and
over the last days the target mode team has been tracking down an
tcm_qla2xxx specific active I/O shutdown bug that appears to now be
almost squashed for 3.5-rc-fixes."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (47 commits)
iscsi-target: Fix iov_count calculation bug in iscsit_allocate_iovecs
iscsi-target: remove dead code in iscsi_check_valuelist_for_support
target: Handle ATA_16 passthrough for pSCSI backend devices
target: Add MI_REPORT_TARGET_PGS ext. header + implict_trans_secs attribute
target: Fix MAINTENANCE_IN service action CDB checks to use lower 5 bits
target: add support for the WRITE_VERIFY command
target: make target_put_session void
target: cleanup transport_execute_tasks()
target: Remove max_sectors device attribute for modern se_task less code
target: lock => unlock typo in transport_lun_wait_for_tasks
target: Enforce hw_max_sectors for SCF_SCSI_DATA_SG_IO_CDB
target: remove the t_se_count field in struct se_cmd
target: remove the t_task_cdbs_ex_left field in struct se_cmd
target: remove the t_task_cdbs_left field in struct se_cmd
target: remove struct se_task
target: move the state and execute lists to the command
target: simplify command to task linkage
target: always allocate a single task
target: replace ->execute_task with ->execute_cmd
target: remove the task_sectors field in struct se_task
...
- Generic Device Tree bindings and hooks for drivers so we can
move over modern drivers to using this.
- Device Tree bindings for Tegra SoCs.
- Funneling some devicetree helper code for the drivers/of
subsystem.
- New pin control drivers for:
- Freescale MXS
- Freescale i.MX51
- Freescale i.MX53
- All of these use Device Tree bindings.
- Dummy pinctrl handles for stepwise migration to pinctrl, akin
to dummy regulators.
- Minor non-urgent fixes and improvments.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJPuiZMAAoJEEEQszewGV1zMK4P/RP+RvKs3KnFaAUF/tM2QSll
/65BW8SJlaXrbMv5IC4iBvUx1sH/fDNtNjTHIwwlNBlrxPl6TVecvZZq+yBnl7yp
Wue0A/xdD0nsD7O/85khVE4WnDJbWpgOdX/9CTVbc6tmTAsb9pGBH2120dtLdcLe
X+GRKnf5D05ySHaGKO8j0PB1MLjF/SV3GhGfrYpn0dtW/XVWNmRczLgm0p11qhMd
kOLoqjcJUp/p3HYtUjKKnwj/3z0d88YjegsiSelTp9Gdnjp/3c2LrRN91mXdIiMc
IGZrp+AQWQ0zg3QrH91gAD7V+f+URrd+IK2EU5PdBO1fqNXgaotGujsX0lqnwycN
8PbXnrUhMhtM4oVjUdLioTP98wIN8Y5tTDoPoVUPtA3921aCVQoE/Pf9/VXBwzEZ
O/nmW0hz7e1OraEq4a/vsD715iuxV92lQzJpzMWYjySFyIGur/VCLLWQo95WWK5d
Foiif1FTuN+1ueONlI5JHqhFp1HZs0ldVDxR/V8G+ueUNlgQmlypgC3lI++WjXnt
uaQS6Hq0NlOKivhlu/uJ098ft7gf2utJLSBOfKPoILgyfksvEGfegJ8tql2YW/vS
42d0jQGrnhi4nctxzGN3zmr4Ys0BU97JP/9Rq+ZbPUL+SDF7e3y4pv+uTLI4ip6v
fyHZTFW6CTXbBD3k1qy9
=RgIp
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control subsystem changes from Linus Walleij:
- Generic Device Tree bindings and hooks for drivers so we can move
over modern drivers to using this.
- Device Tree bindings for Tegra SoCs.
- Funneling some devicetree helper code for the drivers/of subsystem.
- New pin control drivers for:
* Freescale MXS
* Freescale i.MX51
* Freescale i.MX53
All of these use Device Tree bindings.
- Dummy pinctrl handles for stepwise migration to pinctrl, akin to
dummy regulators.
- Minor non-urgent fixes and improvments.
Fix up trivial conflicts in Documentation/driver-model/devres.txt and
drivers/pinctrl/core.c,
* tag 'pinctrl-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (46 commits)
pinctrl: pinctrl-imx: add imx51 pinctrl driver
pinctrl: pinctrl-imx: add imx53 pinctrl driver
pinctrl: pinctrl-pxa3xx: remove empty pinmux disable function
pinctrl: pinctrl-mxs: remove empty pinmux disable function
pinctrl: pinctrl-imx: remove empty pinmux disable function
pinctrl: make pinmux disable function optional
pinctrl: a minor error checking improvement for pinconf
pinctrl: mxs: skip gpio nodes for group creation
pinctrl: mxs: create group for pin config node
pinctrl: (cosmetic) fix two entries in DocBook comments
pinctrl: add more info to error msgs in pin_request
pinctrl: add pinctrl-mxs support
pinctrl: pinctrl-imx: add imx6q pinctrl driver
pinctrl: pinctrl-imx: add imx pinctrl core driver
dt: add of_get_child_count helper function
pinctrl: support gpio request deferred probing
pinctrl: add pinctrl_provide_dummies interface for platforms to use
pinctrl: enhance reporting of errors when loading from DT
pinctrl: add kerneldoc for pinctrl_ops device tree functions
pinctrl: propagate map validation errors
...
The major thing here is the addition of some helpers to factor code out
of drivers, making a fair proportion of regulators much more just data
rather than code which is nice.
- Helpers in the core for regulators using regmap, providing generic
implementations of the enable and voltage selection operations which
just need data to describe them in the drivers.
- Split out voltage mapping and voltage setting, allowing many more
drivers to take advantage of the infrastructure for selectors.
- Loads and loads of cleanups from Axel Lin once again, including many
changes to take advantage of the above new framework features
- New drivers for Ricoh RC5T583, TI TPS62362, TI TPS62363, TI TPS65913,
TI TWL6035 and TI TWL6037.
Some of the registration changes to support the core refactoring caused
so many conflicts that eventually topic branches were abandoned for this
release.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UR7s
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The major thing here is the addition of some helpers to factor code
out of drivers, making a fair proportion of regulators much more just
data rather than code which is nice.
- Helpers in the core for regulators using regmap, providing generic
implementations of the enable and voltage selection operations which
just need data to describe them in the drivers.
- Split out voltage mapping and voltage setting, allowing many more
drivers to take advantage of the infrastructure for selectors.
- Loads and loads of cleanups from Axel Lin once again, including many
changes to take advantage of the above new framework features
- New drivers for Ricoh RC5T583, TI TPS62362, TI TPS62363, TI
TPS65913, TI TWL6035 and TI TWL6037.
Some of the registration changes to support the core refactoring
caused so many conflicts that eventually topic branches were abandoned
for this release."
* tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (227 commits)
regulator: tps65910: use of_node of matched regulator being register
regulator: tps65910: dt: support when "regulators" node found
regulator: tps65910: add error message in case of failure
regulator: tps62360: dt: initialize of_node param for regulator register.
regulator: tps65910: use devm_* for memory allocation
regulator: tps65910: use small letter for regulator names
mfd: tpx6586x: Depend on regulator
regulator: regulator for Palmas Kconfig
regulator: regulator driver for Palmas series chips
regulator: Enable Device Tree for the db8500-prcmu regulator driver
regulator: db8500-prcmu: Separate regulator registration from probe
regulator: ab3100: Use regulator_map_voltage_iterate()
regulator: tps65217: Convert to set_voltage_sel and map_voltage
regulator: Enable the ab8500 for Device Tree
regulator: ab8500: Split up probe() into manageable pieces
regulator: max8925: Remove check_range function and max_uV from struct rc5t583_regulator_info
regulator: max8649: Remove unused check_range() function
regulator: rc5t583: Remove max_uV from struct rc5t583_regulator_info
regulator: da9052: Convert to set_voltage_sel and map_voltage
regulator: max8952: Use devm_kzalloc
...
A surprisingly large series of updates for regmap this time, mostly due
to all the work Stephen Warren has done to add support for MMIO buses.
This wasn't really the target for the framework but it turns out that
there's a reasonable number of cases where it's very helpful to use the
register cache support to allow the register map to remain available
while the device is suspended.
- A MMIO bus implementation, contributed by Stephen Warren. Currently this
is limited to 32 bit systems and native endian registers.
- Support for naming register maps, mainly intended for MMIO devices with
multiple register banks. This was also contributed by Stephen Warren.
- Support for register striding, again contributed by Stephen Warren and
mainly intended for use with MMIO as typically the registers will be a
fixed size but byte addressed.
- irqdomain support for the generic regmap irq_chip, including support
for dynamically allocate interrupt numbers.
- A function dev_get_regmap() which allows frameworks using regmap to
obtain the regmap for a device from the struct device, making life a
little simpler for them.
- Updates to regmap-irq to support more chips (contributed by Graeme
Gregory) and to use irqdomains.
- Support for devices with 24 bit register addresses.
The striding support collided with all the topic branches so the
branches look a bit messy and eventually I just gave up. There's also
the TI Palmas driver and a couple of other isolated MFD patches that
all depend on new regmap features so are being merged here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pjN4
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A surprisingly large series of updates for regmap this time, mostly
due to all the work Stephen Warren has done to add support for MMIO
buses. This wasn't really the target for the framework but it turns
out that there's a reasonable number of cases where it's very helpful
to use the register cache support to allow the register map to remain
available while the device is suspended.
- A MMIO bus implementation, contributed by Stephen Warren. Currently
this is limited to 32 bit systems and native endian registers.
- Support for naming register maps, mainly intended for MMIO devices
with multiple register banks. This was also contributed by Stephen
Warren.
- Support for register striding, again contributed by Stephen Warren
and mainly intended for use with MMIO as typically the registers
will be a fixed size but byte addressed.
- irqdomain support for the generic regmap irq_chip, including support
for dynamically allocate interrupt numbers.
- A function dev_get_regmap() which allows frameworks using regmap to
obtain the regmap for a device from the struct device, making life a
little simpler for them.
- Updates to regmap-irq to support more chips (contributed by Graeme
Gregory) and to use irqdomains.
- Support for devices with 24 bit register addresses.
The striding support collided with all the topic branches so the
branches look a bit messy and eventually I just gave up. There's also
the TI Palmas driver and a couple of other isolated MFD patches that
all depend on new regmap features so are being merged here."
* tag 'regmap-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (24 commits)
mfd: palmas PMIC device support Kconfig
mfd: palmas PMIC device support
regmap: Fix typo in IRQ register striding
mfd: wm8994: Update to fully use irq_domain
regmap: add support for non contiguous status to regmap-irq
regmap: Convert regmap_irq to use irq_domain
regmap: Pass back the allocated regmap IRQ controller data
mfd: da9052: Fix genirq abuse
regmap: Implement dev_get_regmap()
regmap: Devices using format_write don't support bulk operations
regmap: Converts group operation into single read write operations
regmap: Cache single values read from the chip
regmap: fix compile errors in regmap-irq.c due to stride changes
regmap: implement register striding
regmap: fix compilation when !CONFIG_DEBUG_FS
regmap: allow regmap instances to be named
regmap: validate regmap_raw_read/write val_len
regmap: mmio: remove some error checks now in the core
regmap: mmio: convert some error returns to BUG()
regmap: add MMIO bus support
...
The function, timekeeping_leap_insert, was removed in commit
6b43ae8a61
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Pull core ARM updates from Russell King:
"This is the bulk of the core ARM updates for this merge window.
Included in here is a different way to handle the VIVT cache flushing
on context switch, which should allow scheduler folk to remove a
special case in their core code.
We have architectured timer support here, which is a set of timers
specified by the ARM architecture for future SoCs. So we should see
less variability in timer design going forward.
The last big thing here is my cleanup to the way we handle PCI across
ARM, fixing some oddities in some platforms which hadn't realised
there was a way to deal with their private data already built in to
our PCI backend.
I've also removed support for the ARMv3 architecture; it hasn't worked
properly for years so it seems pointless to keep it around."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (47 commits)
ARM: PCI: remove per-pci_hw list of buses
ARM: PCI: dove/kirkwood/mv78xx0: use sys->private_data
ARM: PCI: provide a default bus scan implementation
ARM: PCI: get rid of pci_std_swizzle()
ARM: PCI: versatile: fix PCI interrupt setup
ARM: PCI: integrator: use common PCI swizzle
ARM: 7416/1: LPAE: Remove unused L_PTE_(BUFFERABLE|CACHEABLE) macros
ARM: 7415/1: vfp: convert printk's to pr_*'s
ARM: decompressor: avoid speculative prefetch from non-RAM areas
ARM: Remove ARMv3 support from decompressor
ARM: 7413/1: move read_{boot,persistent}_clock to the architecture level
ARM: Remove support for ARMv3 ARM610 and ARM710 CPUs
ARM: 7363/1: DEBUG_LL: limit early mapping to the minimum
ARM: 7391/1: versatile: add some auxdata for device trees
ARM: 7389/2: plat-versatile: modernize FPGA IRQ controller
AMBA: get rid of last two uses of NO_IRQ
ARM: 7408/1: cacheflush: return error to userspace when flushing syscall fails
ARM: 7409/1: Do not call flush_cache_user_range with mmap_sem held
ARM: 7404/1: cmpxchg64: use atomic64 and local64 routines for cmpxchg64
ARM: 7347/1: SCU: use cpu_logical_map for per-CPU low power mode
...
Pull clkdev updates from Russell King:
"This supplements clkdev with a device-managed API, allowing drivers
cleanup paths to be simplified. We also optimize clk_find() so that
it exits as soon as it finds a perfect match, and we provide a way to
minimise the amount of code platforms need to register clkdev entries.
Some of the code in arm-soc depends on these changes."
* 'clkdev' of git://git.linaro.org/people/rmk/linux-arm:
CLKDEV: provide helpers for common clock framework
ARM: 7392/1: CLKDEV: Optimize clk_find()
ARM: 7376/1: clkdev: Implement managed clk_get()
Pull m68k updates from Geert Uytterhoeven.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Setup CROSS_COMPILE at the top
m68k: Correct the Atari ALLOWINT definition
m68k/video: Create <asm/vga.h>
m68k: Make sure {read,write}s[bwl]() are always defined
m68k/mm: Port OOM changes to do_page_fault()
scsi/atari: Make more functions static
scsi/atari: Revive "atascsi=" setup option
net/ariadne: Improve debug prints
m68k/atari: Change VME irq numbers from unsigned long to unsigned int
m68k/amiga: Use arch_initcall() for registering platform devices
m68k/amiga: Add error checks when registering platform devices
m68k/amiga: Mark z_dev_present() __init
m68k: Remove unused MAX_NOINT_IPL definition
As it's only user (UML) does no longer need it we can get
rid of it.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
PV on HVM guests map GSIs into event channels. At restore time the
event channels are resumed by restore_pirqs.
Device drivers might try to register the same GSI again through ACPI at
restore time, but the GSI has already been mapped and bound by
restore_pirqs. This patch detects these situations and avoids
mapping the same GSI multiple times.
Without this patch we get:
(XEN) irq.c:2235: dom4: pirq 23 or emuirq 28 already mapped
and waste a pirq.
CC: stable@kernel.org
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Pull networking changes from David Miller:
1) Get rid of the error prone NLA_PUT*() macros that used an embedded
goto.
2) Kill off the token-ring and MCA networking drivers, from Paul
Gortmaker.
3) Reduce high-order allocations made by datagram AF_UNIX sockets, from
Eric Dumazet.
4) Add PTP hardware clock support to IGB and IXGBE, from Richard
Cochran and Jacob Keller.
5) Allow users to query timestamping capabilities of a card via
ethtool, from Richard Cochran.
6) Add loadbalance mode to the teaming driver, from Jiri Pirko. Part
of this is that we can now have BPF filters not attached to sockets,
and the loadbalancing function is calculated using one.
7) Francois Romieu went through the network drivers removing gratuitous
uses of netdev->base_addr, perhaps some day we can remove it
completely but it's used for ISA probing still.
8) Add a BPF JIT for sparc. I know, who cares, right? :-)
9) Move networking sysctl registry away from using the compatability
mode interfaces in the sysctl code. From Eric W Biederman.
10) Pavel Emelyanov added a way to save and restore TCP socket state via
TCP_REPAIR, TCP_REPAIR_QUEUE, and TCP_QUEUE_SEQ socket options as
well as a way to forcefully bind a socket to a port via the
sk->sk_reuse value SK_FORCE_REUSE. There is also a
TCP_REPAIR_OPTIONS which allows to reinstante the TCP options
enabled on the connection.
11) Several enhancements from Eric Dumazet that, in particular, can
enhance splice performance on TCP sockets significantly.
a) Reset the offset of the per-socket sendmsg page when we know
we're the only use of the page in linear_to_page().
b) Add facilities such that skb->data can be backed a page rather
than SLAB kmalloc'd memory. In particular devices which were
receiving into linear RX buffers can now end up providing paged
data.
The big result is that code like splice and GRO do not have to copy
any more.
12) Allow a pure sender to more gracefully handle ACK backlogs in TCP.
What can happen at high rates is that the sender hasn't grown his
receive buffer limits at all (he's not receiving data so really
doesn't need to), but the non-data ACKs consume receive buffer
space.
sk_add_backlog() is too aggressive in dropping frames in this case,
so relax it's requirements by using the receive buffer plus the send
buffer limit as the backlog limit instead of just the former.
Also from Eric Dumazet.
13) Add ipv6 support to L2TP, from Benjamin LaHaise, James Chapman, and
Chris Elston.
14) Implement TCP early retransmit (RFC 5827), from Yuchung Cheng.
Basically, we can start fast retransmit before hiting the dupack
threshold under certain conditions.
15) New CODEL active queue management packet scheduler, from Eric
Dumazet based upon initial work by Dave Taht.
Basically, the big feature is that packets are dropped (or ECN bits
are set) based upon how long packets live in the queue, rather than
the queue length (which is what RED uses).
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1341 commits)
drivers/net/stmmac: seq_file fix memory leak
ipv6/exthdrs: strict Pad1 and PadN check
USB: qmi_wwan: Add ZTE (Vodafone) K3520-Z
USB: qmi_wwan: Add ZTE (Vodafone) K3765-Z
USB: qmi_wwan: Make forced int 4 whitelist generic
net/ipv4: replace simple_strtoul with kstrtoul
net/ipv4/ipconfig: neaten __setup placement
net: qmi_wwan: Add Vodafone/Huawei K5005 support
net: cdc_ether: Add ZTE WWAN matches before generic Ethernet
ipv6: use skb coalescing in reassembly
ipv4: use skb coalescing in defragmentation
net: introduce skb_try_coalesce()
net:ipv6:fixed space issues relating to operators.
net:ipv6:fixed a trailing white space issue.
ipv6: disable GSO on sockets hitting dst_allfrag
tg3: use netdev_alloc_frag() API
net: napi_frags_skb() is static
ppp: avoid false drop_monitor false positives
ipv6: bool/const conversions phase2
ipx: Remove spurious NULL checking in ipx_ioctl().
...
When CONFIG_PM=n, make sure that the usb_[unlocked_][en/dis]able_lpm
declarations are visible in include/linux/usb.h, and exported from
drivers/usb/core/hub.c.
Before this patch, if CONFIG_USB_SUSPEND was turned off, it would cause
build errors:
drivers/usb/core/hub.c: In function 'usb_disable_lpm':
drivers/usb/core/hub.c:3394:2: error: implicit declaration of function 'usb_enable_lpm' [-Werror=implicit-function-declaration]
drivers/usb/core/hub.c: At top level:
drivers/usb/core/hub.c:3424:6: warning: conflicting types for 'usb_enable_lpm' [enabled by default]
drivers/usb/core/hub.c:3394:2: note: previous implicit declaration of 'usb_enable_lpm' was here
drivers/usb/core/driver.c: In function 'usb_probe_interface':
drivers/usb/core/driver.c:339:2: error: implicit declaration of function 'usb_unlocked_disable_lpm' [-Werror=implicit-function-declaration]
drivers/usb/core/driver.c:364:3: error: implicit declaration of function 'usb_unlocked_enable_lpm' [-Werror=implicit-function-declaration]
drivers/usb/core/message.c: In function 'usb_set_interface':
drivers/usb/core/message.c:1314:2: error: implicit declaration of function 'usb_disable_lpm' [-Werror=implicit-function-declaration]
drivers/usb/core/message.c:1323:3: error: implicit declaration of function 'usb_enable_lpm' [-Werror=implicit-function-declaration]
drivers/usb/core/message.c:1368:2: error: implicit declaration of function 'usb_unlocked_enable_lpm' [-Werror=implicit-function-declaration]
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Chen Peter-B29397 <B29397@freescale.com>
This branch simplifies and clarifies the dcache lookup, and allows us to
do certain nice optimizations when comparing dentries. It also cleans
up the interface to __d_lookup_rcu(), especially around passing the
inode information around.
* dentry-cleanups:
vfs: make it possible to access the dentry hash/len as one 64-bit entry
vfs: move dentry name length comparison from dentry_cmp() into callers
vfs: do the careful dentry name access for all dentry_cmp cases
vfs: remove unnecessary d_unhashed() check from __d_lookup_rcu
vfs: clean up __d_lookup_rcu() and dentry_cmp() interfaces
This series sanitizes the interface to unmap_vma(). The crazy interface
annoyed me no end when I was looking at unmap_single_vma(), which we can
spend quite a lot of time in (especially with loads that have a lot of
small fork/exec's: shell scripts etc).
Moving the nr_accounted calculations to where they belong at least
clarifies things a little. I hope to come back to look at the
performance of this later, but if/when I get back to it I at least don't
have to see the crazy interfaces any more.
* vm-cleanups:
vm: remove 'nr_accounted' calculations from the unmap_vmas() interfaces
vm: simplify unmap_vmas() calling convention
There are two functions in this asm-generic file. Looking at
other arch which do not use the generic version, these two fcns
are within an #ifdef __KERNEL__ block, so make the generic one
consistent with those.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add an ioctl to the /dev/xen/xenbus_backend device allowing the xenbus
backend to be started after the kernel has booted. This allows xenstore
to run in a different domain from the dom0.
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
On MIPS we want to call of_irq_map_pci from inside
arch/mips/include/asm/pci.h:extern int pcibios_map_irq(
const struct pci_dev *dev, u8 slot, u8 pin);
For this to work we need to change several functions to const usage.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-pci@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-mips@linux-mips.org
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3710/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Contiguous Memory Allocator is a set of helper functions for DMA
mapping framework that improves allocations of contiguous memory chunks.
CMA grabs memory on system boot, marks it with MIGRATE_CMA migrate type
and gives back to the system. Kernel is allowed to allocate only movable
pages within CMA's managed memory so that it can be used for example for
page cache when DMA mapping do not use it. On
dma_alloc_from_contiguous() request such pages are migrated out of CMA
area to free required contiguous block and fulfill the request. This
allows to allocate large contiguous chunks of memory at any time
assuming that there is enough free memory available in the system.
This code is heavily based on earlier works by Michal Nazarewicz.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
alloc_contig_range() performs memory allocation so it also should keep
track on keeping the correct level of memory watermarks. This commit adds
a call to *_slowpath style reclaim to grab enough pages to make sure that
the final collection of contiguous pages from freelists will not starve
the system.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
This commit changes various functions that change pages and
pageblocks migrate type between MIGRATE_ISOLATE and
MIGRATE_MOVABLE in such a way as to allow to work with
MIGRATE_CMA migrate type.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
The MIGRATE_CMA migration type has two main characteristics:
(i) only movable pages can be allocated from MIGRATE_CMA
pageblocks and (ii) page allocator will never change migration
type of MIGRATE_CMA pageblocks.
This guarantees (to some degree) that page in a MIGRATE_CMA page
block can always be migrated somewhere else (unless there's no
memory left in the system).
It is designed to be used for allocating big chunks (eg. 10MiB)
of physically contiguous memory. Once driver requests
contiguous memory, pages from MIGRATE_CMA pageblocks may be
migrated away to create a contiguous block.
To minimise number of migrations, MIGRATE_CMA migration type
is the last type tried when page allocator falls back to other
migration types when requested.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
This commit adds the alloc_contig_range() function which tries
to allocate given range of pages. It tries to migrate all
already allocated pages that fall in the range thus freeing them.
Once all pages in the range are freed they are removed from the
buddy system thus allocated for the caller to use.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
Add a common helper for dma-mapping core for mapping a coherent buffer
to userspace.
Reported-by: Subash Patel <subashrp@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-By: Subash Patel <subash.ramaswamy@linaro.org>
1/ Rework remote-node-context (RNC) handling for proper management of
the silicon state machine in error handling and hot-plug conditions.
Further details below, suffice to say if the RNC is mismanaged the
silicon state machines may lock up.
2/ Refactor the initialization code to be reused for suspend/resume support
3/ Miscellaneous bug fixes to address discovery issues and hardware
compatibility.
RNC rework details from Jeff Skirvin:
In the controller, devices as they appear on a SAS domain (or
direct-attached SATA devices) are represented by memory structures known
as "Remote Node Contexts" (RNCs). These structures are transferred from
main memory to the controller using a set of register commands; these
commands include setting up the context ("posting"), removing the
context ("invalidating"), and commands to control the scheduling of
commands and connections to that remote device ("suspensions" and
"resumptions"). There is a similar path to control RNC scheduling from
the protocol engine, which interprets the results of command and data
transmission and reception.
In general, the controller chooses among non-suspended RNCs to find one
that has work requiring scheduling the transmission of command and data
frames to a target. Likewise, when a target tries to return data back
to the initiator, the state of the RNC is used by the controller to
determine how to treat the incoming request. As an example, if the RNC
is in the state "TX/RX Suspended", incoming SSP connection requests from
the target will be rejected by the controller hardware. When an RNC is
"TX Suspended", it will not be selected by the controller hardware to
start outgoing command or data operations (with certain priority-based
exceptions).
As mentioned above, there are two sources for management of the RNC
states: commands from driver software, and the result of transmission
and reception conditions of commands and data signaled by the controller
hardware. As an example of the latter, if an outgoing SSP command ends
with a OPEN_REJECT(BAD_DESTINATION) status, the RNC state will
transition to the "TX Suspended" state, and this is signaled by the
controller hardware in the status to the completion of the pending
command as well as signaled in a controller hardware event. Examples of
the former are included in the patch changelogs.
Driver software is required to suspend the RNC in a "TX/RX Suspended"
condition before any outstanding commands can be terminated. Failure to
guarantee this can lead to a complete hardware hang condition. Earlier
versions of the driver software did not guarantee that an RNC was
correctly managed before I/O termination, and so operated in an unsafe
way.
Further, the driver performed unnecessary contortions to preserve the
remote device command state and so was more complicated than it needed
to be. A simplifying driver assumption is that once an I/O has entered
the error handler path without having completed in the target, the
requirement on the driver is that all use of the sas_task must end.
Beyond that, recovery of operation is dependent on libsas and other
components to reset, rediscover and reconfigure the device before normal
operation can restart. In the driver, this simplifying assumption meant
that the RNC management could be reduced to entry into the suspended
state, terminating the targeted I/O request, and resuming the RNC as
needed for device-specific management such as an SSP Abort Task or LUN
Reset Management request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HYvO
-----END PGP SIGNATURE-----
Merge tag 'isci-for-3.5' into misc
isci update for 3.5
1/ Rework remote-node-context (RNC) handling for proper management of
the silicon state machine in error handling and hot-plug conditions.
Further details below, suffice to say if the RNC is mismanaged the
silicon state machines may lock up.
2/ Refactor the initialization code to be reused for suspend/resume support
3/ Miscellaneous bug fixes to address discovery issues and hardware
compatibility.
RNC rework details from Jeff Skirvin:
In the controller, devices as they appear on a SAS domain (or
direct-attached SATA devices) are represented by memory structures known
as "Remote Node Contexts" (RNCs). These structures are transferred from
main memory to the controller using a set of register commands; these
commands include setting up the context ("posting"), removing the
context ("invalidating"), and commands to control the scheduling of
commands and connections to that remote device ("suspensions" and
"resumptions"). There is a similar path to control RNC scheduling from
the protocol engine, which interprets the results of command and data
transmission and reception.
In general, the controller chooses among non-suspended RNCs to find one
that has work requiring scheduling the transmission of command and data
frames to a target. Likewise, when a target tries to return data back
to the initiator, the state of the RNC is used by the controller to
determine how to treat the incoming request. As an example, if the RNC
is in the state "TX/RX Suspended", incoming SSP connection requests from
the target will be rejected by the controller hardware. When an RNC is
"TX Suspended", it will not be selected by the controller hardware to
start outgoing command or data operations (with certain priority-based
exceptions).
As mentioned above, there are two sources for management of the RNC
states: commands from driver software, and the result of transmission
and reception conditions of commands and data signaled by the controller
hardware. As an example of the latter, if an outgoing SSP command ends
with a OPEN_REJECT(BAD_DESTINATION) status, the RNC state will
transition to the "TX Suspended" state, and this is signaled by the
controller hardware in the status to the completion of the pending
command as well as signaled in a controller hardware event. Examples of
the former are included in the patch changelogs.
Driver software is required to suspend the RNC in a "TX/RX Suspended"
condition before any outstanding commands can be terminated. Failure to
guarantee this can lead to a complete hardware hang condition. Earlier
versions of the driver software did not guarantee that an RNC was
correctly managed before I/O termination, and so operated in an unsafe
way.
Further, the driver performed unnecessary contortions to preserve the
remote device command state and so was more complicated than it needed
to be. A simplifying driver assumption is that once an I/O has entered
the error handler path without having completed in the target, the
requirement on the driver is that all use of the sas_task must end.
Beyond that, recovery of operation is dependent on libsas and other
components to reset, rediscover and reconfigure the device before normal
operation can restart. In the driver, this simplifying assumption meant
that the RNC management could be reduced to entry into the suspended
state, terminating the targeted I/O request, and resuming the RNC as
needed for device-specific management such as an SSP Abort Task or LUN
Reset Management request.
This patch modifies ubi_wl_flush to force the erasure of
particular volume id / logical eraseblock number pairs. Previous functionality
is preserved when passing UBI_ALL for both values. The locations where ubi_wl_flush
were called are appropriately changed: ubi_leb_erase only flushes for the
erased LEB, and ubi_create_volume forces only flushing for its volume id.
External code can call this new feature via the new function ubi_flush() added
to kapi.c, which simply passes through to ubi_wl_flush().
This was tested by disabling the call to do_work in ubi thread, which results
in the work queue remaining unless explicitly called to remove. UBIFS was
changed to call ubifs_leb_change 50 times for four different LEBs. Then the
new function was called to clear the queue: passing wrong volume ids / lnum,
correct ones, and finally UBI_ALL for both to ensure it was finally all
cleard. The work queue was dumped each time and the selective removal
of the particular LEB numbers was observed. Extra checks were enabled and
ubifs's integck was also run. Finally, the drive was repeatedly filled and
emptied to ensure that the queue was cleared normally.
Artem: amended the patch.
Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Joel will use it in his 'ubi_flush()' extention to specify all eraseblocks.
Also amend the comment for UBI_UNKNOWN - it is used beyond attaching info
structure now.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Fixes for perf/core:
- Rename some perf_target methods to avoid double negation, from Namhyung Kim.
- Revert change to use per task events with inheritance, from Namhyung Kim.
- Events should start disabled till children starts running, from David Ahern.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When reshaping we can avoid costly intermediate backup by
changing the 'start' address of the array on the device
(if there is enough room).
So as a first step, allow such a change to be requested
through sysfs, and recorded in v1.x metadata.
(As we didn't previous check that all 'pad' fields were zero,
we need a new FEATURE flag for this.
A (belatedly) check that all remaining 'pad' fields are
zero to avoid a repeat of this)
The new data offset must be requested separately for each device.
This allows each to have a different change in the data offset.
This is not likely to be used often but as data_offset can be
set per-device, new_data_offset should be too.
This patch also removes the 'acknowledged' arg to rdev_set_badblocks as
it is never used and never will be. At the same time we add a new
arg ('in_new') which is currently always zero but will be used more
soon.
When a reshape finishes we will need to update the data_offset
and rdev->sectors. So provide an exported function to do that.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently a reshape operation always progresses from the start
of the array to the end unless the number of devices is being
reduced, in which case it progressed in the opposite direction.
To reverse a partial reshape which changes the number of devices
you can stop the array and re-assemble with the raid-disks numbers
reversed and it will undo.
However for a reshape that does not change the number of devices
it is not possible to reverse the reshape in the middle - you have to
wait until it completes.
So add a 'reshape_direction' attribute with is either 'forwards' or
'backwards' and can be explicitly set when delta_disks is zero.
This will become more important when we allow the data_offset to
change in a reshape. Then the explicit statement of what direction is
being used will be more useful.
This can be enabled in raid5 trivially as it already supports
reverse reshape and just needs to use a different trigger to request it.
Signed-off-by: NeilBrown <neilb@suse.de>
Richard removed the "dtype" hint, but few commentaries were left and this patch
removes them. I've also added a better description about the "dtype" field in
the ubi-user.h for people who may ever wonder what was that dtype thing about.
This patch also adds an important note that it is better to use value "3" for
the "dtype" field.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This finally removes the data type hint from the UBI ABI.
>From now on the "dtype" field will be ignored and must not used
anymore.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
We do not need this feature and to our shame it even was not working
and there was a bug found very recently.
-- Artem Bityutskiy
Without the data type hint UBI2 (fastmap) will be easier to implement.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Instead of providing a function in platform data, allow also providing the
name of the external clock and use it through the clock framework.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As with the existing emulation this should not be used in production
systems but is useful for test purposes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds ADC support to the DA9052/53 core.
Tested on smdkv6410 and i.mx53 QS boards.
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This change changes the tps65910-irq code to use irqdomain, and support
initialization from devicetree. This assumes that the irq_base in the
platform data is -1 if devicetree is used.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
- rename to anatop_read_reg and anatop_write_reg
- anatop_read_reg directly return reg value
- anatop_write_reg write reg with mask
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The modern idiom is to use irq_domain to allocate interrupts. This is
useful partly to allow further infrastructure to be based on the domains
and partly because it makes it much easier to allocate virtual interrupts
to devices as we don't need to allocate a contiguous range of interrupt
numbers.
Convert the wm831x driver over to this infrastructure, using a legacy
IRQ mapping if an irq_base is specified in platform data and otherwise
using a linear mapping, always registering the interrupts even if they
won't ever be used. Only boards which need to use the GPIOs as
interrupts should need to use an irq_base.
This means that we can't use the MFD irq_base management since the
unless we're using an explicit irq_base from platform data we can't rely
on a linear mapping of interrupts. Instead we need to map things via
the irq_domain - provide a conveniencem function wm831x_irq() to save a
small amount of typing when doing so. Looking at this I couldn't clearly
see anything the MFD core could do to make this nicer.
Since we're not supporting device tree yet there's no meaningful
advantage if we don't do this conversion in one, the fact that the
interrupt resources are used for repeated IP blocks makes accessor
functions for the irq_domain more trouble to do than they're worth.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch supports IRQ handling for MAX77693.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds MFD driver for MAX77693 to enable its sub devices.
The MAX77693 is a multi-function devices. It includes PMIC,
MUIC(Micro USB Interface Controller), flash LED control and
haptic motor control.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use SI-units (uA) for max-current interface (5000 - 29800 uA).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The max-current attributes of the subdrivers have been dropped so
remove the no longer used lm3533_ctrlbank_get_max_current function.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add boost-frequency and over-voltage-protection settings to platform
data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Save a useful amount of code by removing the custom cache implementation
for wm8400 and using the regmap cache. Also simplify things by not
separately reseting the CODEC registers, this is a sufficiently infrequent
operation that we can simply invalidate the entire cache when this happens.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As gpio support for tps65910 is on gpio driver, registering
gpio support as the mfd sub devices instead of calling gpio_init()
from the core probe.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
twl-regulator has a collection of feature flags, some defined
in twl-core.c and one defined in i2c/twl.h.
This is confusing for anyone adding a new feature flag.
So collect them together and place them in twl.h immediately
after the structure in which they are initially set.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This change removes the read/write callback functions in favor of common
regmap accessors inside the header file. This change also makes use of
regmap_read/write for single register access which maps better onto what this
driver actually needs.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add another Medion X10 remote keymap. This is for the Medion OR2x
remotes with the Windows MCE button.
The receiver shipped with this remote has the same USB ID as the other
Medion receivers, but the name is different and is therefore used to
detect this variant.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro is proposing a new API to handle statistics. This functionality will
be returned after the statistics API is ready. Just remove them for now.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
increment the DVB API version to 5.6 to signify support for
controlling an ATSC-MH frontend.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is getting more entities to manage within single video pipeline
in newer SoCs. To simplify code put subdevs' pointer into an array
rather than adding new member in struct fimc_pipeline for each subdev.
This allows to easier handle subdev operations in proper order.
Additionally walk graph in one direction only in fimc_pipeline_prepare()
function to make sure we properly gather only media entities that below
to single data pipeline. This avoids wrong initialization in case where,
for example there are multiple active links from s5p-mipi-csis subdev
output pad.
struct fimc_pipeline declaration is moved to the driver's public header
to allow other drivers to reuse the fimc-lite driver added in subsequent
patches.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The DV Preset API will be phased out in favor of the more flexible DV Timings
API. Mark the preset API accordingly in the header and documentation.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This header contains the timings for the common CEA-861 and all VESA
DMT formats for use with the V4L2 dv_timings API.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds dmaengine supporting using sh_dma driver. The module
receives data by DMAC, it also needs TX DMAC to generate SPI's clocks.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move tcp_try_coalesce() protocol independent part to
skb_try_coalesce().
skb_try_coalesce() can be used in IPv4 defrag and IPv6 reassembly,
to build optimized skbs (less sk_buff, and possibly less 'headers')
skb_try_coalesce() is zero copy, unless the copy can fit in destination
header (its a rare case)
kfree_skb_partial() is also moved to net/core/skbuff.c and exported,
because IPv6 will need it in patch (ipv6: use skb coalescing in
reassembly).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'emev2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
mach-shmobile: Use DT_MACHINE for KZM9D V3
mach-shmobile: Emma Mobile EV2 DT support V3
mach-shmobile: KZM9D board Ethernet support V3
mach-shmobile: Emma Mobile EV2 GPIO support V3
mach-shmobile: Emma Mobile EV2 SMP support V3
mach-shmobile: KZM9D board support V3
mach-shmobile: Emma Mobile EV2 SoC base support V3
gpio: Emma Mobile GPIO driver V2
Presently irqdomain.h has duplicate definitions for irq_find_host() and
irq_set_default_host(), presumably from merge damage. Kill off the
duplicates.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
SupherH FSI2 can use special data transfer,
but it depends on CPU-FSI2 connection style.
We can use 16bit data stream mode if it was valid connection,
and it is required for 16bit data DMA transfer / SPDIF sound output.
We can use 24bit data transfer if it was invalid connection.
We can select connection type if CPU is SH7372,
and it is always valid connection if latest SuperH.
This patch adds new bus_option and fsi_bus_setup()
for supporting these feature.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that IRQ domains are being used by modules it's necessary to support
removing them, too. This adds a new irq_domain_remove() routine for doing
the bulk of the heavy lifting. It's left as an exercise to the caller to
ensure all mappings have been appropriatey disposed of before attempting
to remove the domain.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It fixes the issue in gpio-generic that commit fb14921 (gpio/mxc: add
missing initialization of basic_mmio_gpio shadow variables) manged to
fix in gpio-mxc driver, so that other platform specific drivers do not
suffer from the same problem over and over again.
Changes since v1:
* Turn the last parameter of bgpio_init() "bool big_endian" into
"unsigned long flags" and give those really quirky hardwares a
chance to tell that reg_set and reg_dir are unreadable.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[grant.likely: Fix big-endian usage to explicitly set BBGPIOF_BIG_ENDIAN]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull block layer fixes from Jens Axboe:
"A few small, but important fixes. Most of them are marked for stable
as well
- Fix failure to release a semaphore on error path in mtip32xx.
- Fix crashable condition in bio_get_nr_vecs().
- Don't mark end-of-disk buffers as mapped, limit it to i_size.
- Fix for build problem with CONFIG_BLOCK=n on arm at least.
- Fix for a buffer overlow on UUID partition printing.
- Trivial removal of unused variables in dac960."
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix buffer overflow when printing partition UUIDs
Fix blkdev.h build errors when BLOCK=n
bio allocation failure due to bio_get_nr_vecs()
block: don't mark buffers beyond end of disk as mapped
mtip32xx: release the semaphore on an error path
dac960: Remove unused variables from DAC960_CreateProcEntries()
Mostly bool conversions, some inline removals and const additions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3d0f7cf0 "gpio: Adjust of_xlate API to support multiple GPIO
chips" changed the api of gpiochip_find to drop const from the data
parameter of the match hook, but didn't also drop const from data
causing a build warning.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The PMIC device RC5T583 from RICOH supports 8 gpios.
Adding gpio driver for this device to access the pins
control through gpio library.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[grant.likely: slight cosmetic changes]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It needs parentheses around the argument, so that it can be used with
complex arguments (e.g., "n+5").
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Hi Greg,
Here's the final Link Power Management patches, along with a couple of bug
fixes that have been sitting in my queue. I've fixed all the comments that
Alan and Andiry had on the Link PM patches, so I think they're ready to go.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ixwg
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2012-05-18' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
xhci: Link PM and bug fixes for 3.5.
Hi Greg,
Here's the final Link Power Management patches, along with a couple of bug
fixes that have been sitting in my queue. I've fixed all the comments that
Alan and Andiry had on the Link PM patches, so I think they're ready to go.
Sarah Sharp
This patch changes the of_xlate API to make it possible for multiple
gpio_chips to refer to the same device tree node. This is useful for
banked GPIO controllers that use multiple gpio_chips for a single
device. With this change the core code will try calling of_xlate on
each gpio_chip that references the device_node and will return the
gpio number for the first one to return 'true'.
Tested-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow drivers to use the modern request and configure idiom together
with devres.
As with plain gpio_request() and gpio_request_one() we can't implement
the old school version in terms of _one() as this would force the
explicit selection of a direction in gpio_request() which could break
systems if we pick the wrong one. Implementing devm_gpio_request_one()
in terms of devm_gpio_request() would needlessly complicate things or
lead to duplication from the unmanaged version depending on how it's
done.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The USB 3.0 spec defines a new way of differentiating interrupt
endpoints. The idea is that some interrupt endpoints are used for
notifications, i.e. they continually NAK the transfer until something
changes on the device. Other interrupt endpoints are used as a way to
periodically transfer data.
The USB 3.0 endpoint descriptor uses bits 5:4 of bmAttributes for
interrupt endpoints, to define the endpoint as either a Notification
endpoint, or a Periodic endpoint. Introduce macros to dig out that
information.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
There are several places where the USB core needs to disable USB 3.0
Link PM:
- usb_bind_interface
- usb_unbind_interface
- usb_driver_claim_interface
- usb_port_suspend/usb_port_resume
- usb_reset_and_verify_device
- usb_set_interface
- usb_reset_configuration
- usb_set_configuration
Use the new LPM disable/enable functions to temporarily disable LPM
around these critical sections.
We need to protect the critical section around binding and unbinding USB
interface drivers. USB drivers may want to disable hub-initiated USB
3.0 LPM, which will change the value of the U1/U2 timeouts that the xHCI
driver will install. We need to disable LPM completely until the driver
is bound to the interface, and the driver has a chance to enable
whatever alternate interface setting it needs in its probe routine.
Then re-enable USB3 LPM, and recalculate the U1/U2 timeout values.
We also need to disable LPM in usb_driver_claim_interface,
because drivers like usbfs can bind to an interface through that
function. Note, there is no way currently for userspace drivers to
disable hub-initiated USB 3.0 LPM. Revisit this later.
When a driver is unbound, the U1/U2 timeouts may change because we are
unbinding the last driver that needed hub-initiated USB 3.0 LPM to be
disabled.
USB LPM must be disabled when a USB device is going to be suspended.
The USB 3.0 spec does not define a state transition from U1 or U2 into
U3, so we need to bring the device into U0 by disabling LPM before we
can place it into U3. Therefore, call usb_unlocked_disable_lpm() in
usb_port_suspend(), and call usb_unlocked_enable_lpm() in
usb_port_resume(). If the port suspend fails, make sure to re-enable
LPM by calling usb_unlocked_enable_lpm(), since usb_port_resume() will
not be called on a failed port suspend.
USB 3.0 devices lose their USB 3.0 LPM settings (including whether USB
device-initiated LPM is enabled) across device suspend. Therefore,
disable LPM before the device will be reset in
usb_reset_and_verify_device(), and re-enable LPM after the reset is
complete and the configuration/alt settings are re-installed.
The calculated U1/U2 timeout values are heavily dependent on what USB
device endpoints are currently enabled. When any of the enabled
endpoints on the device might change, due to a new configuration, or new
alternate interface setting, we need to first disable USB 3.0 LPM, add
or delete endpoints from the xHCI schedule, install the new interfaces
and alt settings, and then re-enable LPM. Do this in usb_set_interface,
usb_reset_configuration, and usb_set_configuration.
Basically, there is a call to disable and then enable LPM in all
functions that lock the bandwidth_mutex. One exception is
usb_disable_device, because the device is disconnecting or otherwise
going away, and we should not care about whether USB 3.0 LPM is enabled.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
There are various functions within the USB core that will need to
disable USB 3.0 link power states. For example, when a USB device
driver is being bound to an interface, we need to disable USB 3.0 LPM
until we know if the driver will allow hub-initiated LPM transitions.
Another example is when the USB core is switching alternate interface
settings. The USB 3.0 timeout values are dependent on what endpoints
are enabled, so we want to ensure that LPM is disabled until the new alt
setting is fully installed.
Multiple functions need to disable LPM, and those functions can even be
nested. For example, usb_bind_interface() could disable LPM, and then
call into the driver probe function, which may attempt to switch to a
different alt setting. Therefore, we need to keep a count of the number
of functions that require LPM to be disabled at any point in time.
Introduce two new USB core API calls, usb_disable_lpm() and
usb_enable_lpm(). These functions increment and decrement a new
variable in the usb_device, lpm_disable_count. If usb_disable_lpm()
fails, it will call usb_enable_lpm() in order to balance the
lpm_disable_count.
These two new functions must be called with the bandwidth_mutex locked.
If the bandwidth_mutex is not already held by the caller, it should
instead call usb_unlocked_disable_lpm() and usb_enable_lpm(), which take
the bandwidth_mutex before calling usb_disable_lpm() and
usb_enable_lpm(), respectively.
Introduce a new variable (timeout) in the usb3_lpm_params structure to
keep track of the currently enabled U1/U2 timeout values. When
usb_disable_lpm() is called, and the USB device has the U1 or U2
timeouts set to a non-zero value (meaning either device-initiated or
hub-initiated LPM is enabled), attempt to disable LPM, regardless of the
state of the lpm_disable_count. We want to ensure that all callers can
be guaranteed that LPM is disabled if usb_disable_lpm() returns zero.
Otherwise the following scenario could occur:
1. Driver A is being bound to interface 1. usb_probe_interface()
disables LPM. Driver A doesn't care if hub-initiated LPM is enabled, so
even though usb_disable_lpm() fails, the probe of the driver continues,
and the bandwidth mutex is dropped.
2. Meanwhile, Driver B is being bound to interface 2.
usb_probe_interface() grabs the bandwidth mutex and calls
usb_disable_lpm(). That call should attempt to disable LPM, even
though the lpm_disable_count is set to 1 by Driver A.
For usb_enable_lpm(), we attempt to enable LPM only when the
lpm_disable_count is zero. If some step in enabling LPM fails, it will
only have a minimal impact on power consumption, and all USB device
drivers should still work properly. Therefore don't bother to return
any error codes.
Don't enable device-initiated LPM if the device is unconfigured. The
USB device will only accept the U1/U2_ENABLE control transfers in the
configured state. Do enable hub-initiated LPM in that case, since
devices are allowed to accept the LGO_Ux link commands in any state.
Don't enable or disable LPM if the device is marked as not being LPM
capable. This can happen if:
- the USB device doesn't have a SS BOS descriptor,
- the device's parent hub has a zeroed bHeaderDecodeLatency value, or
- the xHCI host doesn't support LPM.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
USB 3.0 Link Power Management (LPM) is designed to allow individual
links in the bus to go into lower power states. There are two ways a
link can enter a lower power state:
1. Device-initiated LPM. When a USB device decides it can go into a
lower power link state, it sends a message to the parent hub, telling it
to go into either U1 or U2. Device-initiated LPM is good for devices
that send data to the host, like communications devices.
2. Hub-initiated LPM. After the link has been idle for a specific
amount of time, the parent hub will request that the child go into a
lower power state. The child can refuse that request. For example, a
USB modem may want to refuse the LPM request if it is in the middle of
receiving a text message. Hub-initiated LPM is good for devices where
only the host initiates the data transfer, like USB printers or USB mass
storage devices.
Links will be automatically placed into higher power states by the USB
hubs and roothubs whenever the host starts a USB transmission.
Introduce a new usb_driver flag, disable_hub_initiated_lpm, that allows
drivers to disable hub-initiated LPM.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: linux-bluetooth@vger.kernel.org
Cc: gigaset307x-common@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: ath9k-devel@lists.ath9k.org
Cc: libertas-dev@lists.infradead.org
Cc: users@rt2x00.serialmonkey.com
There are several different exit latencies associated with coming out of
the U1 or U2 lower power link state.
Device Exit Latency (DEL) is the maximum time it takes for the USB
device to bring its upstream link into U0. That can be found in the
SuperSpeed Extended Capabilities BOS descriptor for the device. The
time it takes for a particular link in the tree to exit to U0 is the
maximum of either the parent hub's U1/U2 DEL, or the child's U1/U2 DEL.
Hubs introduce a further delay that effects how long it takes a child
device to transition to U0. When a USB 3.0 hub receives a header
packet, it takes some time to decode that header and figure out which
downstream port the packet was destined for. If the port is not in U0,
this hub header decode latency will cause an additional delay for
bringing the child device to U0. This Hub Header Decode Latency is
found in the USB 3.0 hub descriptor.
We can use DEL and the header decode latency, along with additional
latencies imposed by each additional hub tier, to figure out the exit
latencies for both host-initiated and device-initiated exit to U0.
The Max Exit Latency (MEL) is the worst-case time it will take for a
host-initiated exit to U0, based on whether U1 or U2 link states are
enabled. The ping or packet must traverse the path to the device, and
each hub along the way incurs the hub header decode latency in order to
figure out which device the transfer was bound for. We say worst-case,
because some hubs may not be in the lowest link state that is enabled.
See the examples in section C.2.2.1.
Note that "HSD" is a "host specific delay" that the power appendix
architect has not been able to tell me how to calculate. There's no way
to get HSD from the xHCI registers either, so I'm simply ignoring it.
The Path Exit Latency (PEL) is the worst-case time it will take for a
device-initiate exit to U0 to place all the links from the device to the
host into U0.
The System Exit Latency (SEL) is another device-initiated exit latency.
SEL is useful for USB 3.0 devices that need to send data to the host at
specific intervals. The device may send an NRDY to indicate it isn't
ready to send data, then put its link into a lower power state. If it
needs to have that data transmitted at a specific time, it can use SEL
to back calculate when it will need to bring the link back into U0 to
meet its deadlines.
SEL is the worst-case time from the device-initiated exit to U0, to when
the device will receive a packet from the host controller. It includes
PEL, the time it takes for an ERDY to get to the host, a host-specific
delay for the host to process that ERDY, and the time it takes for the
packet to traverse the path to the device. See Figure C-2 in the USB
3.0 bus specification.
Note: I have not been able to get good answers about what the
host-specific delay to process the ERDY should be. The Intel HW
developers say it will be specific to the platform the xHCI host is
integrated into, and they say it's negligible. Ignore this too.
Separate from these four exit latencies are the U1/U2 timeout values we
program into the parent hubs. These timeouts tell the hub to attempt to
place the device into a lower power link state after the link has been
idle for that amount of time.
Create two arrays (one for U1 and one for U2) to store mel, pel, sel,
and the timeout values. Store the exit latency values in nanosecond
units, since that's the smallest units used (DEL is in us, but the Hub
Header Decode Latency is in ns).
If a USB 3.0 device doesn't have a SuperSpeed Extended Capabilities BOS
descriptor, it's highly unlikely it will be able to handle LPM requests
properly. So it's best to disable LPM for devices that don't have this
descriptor, and any children beneath it, if it's a USB 3.0 hub. Warn
users when that happens, since it means they have a non-compliant USB
3.0 device or hub.
This patch assumes a simplified design where links deep in the tree will
not have U1 or U2 enabled unless all their parent links have the
corresponding LPM state enabled. Eventually, we might want to allow a
different policy, and we can revisit this patch when that happens.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
These new ioctls make it possible for the dv_timings API to replace
the dv_preset API eventually.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The generic PM domains core code currently requires domains to be in
the "power on" state for adding devices to them, but this limitation
turns out to be inconvenient in some situations, so remove it.
For this purpose, make __pm_genpd_add_device() set the device's
need_restore flag if the domain is in the "power off" state, so that
the device's "restore state" (usually .runtime_resume()) callback
is executed when it is resumed after the domain has been turned on.
If the domain is in the "power on" state, the device's need_restore
flag will be cleared by __pm_genpd_add_device(), so that its "save
state" (usually .runtime_suspend()) callback is executed when the
domain is about to be turned off. However, since that default
behavior need not be always desirable, add a helper function
pm_genpd_dev_need_restore() allowing a device's need_restore flag
to be set/unset at any time.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fix two issues introduced in commit a1c7fff7e1
( net: netdev_alloc_skb() use build_skb() )
- Must be IRQ safe (non NAPI drivers can use it)
- Must not leak the frag if build_skb() fails to allocate sk_buff
This patch introduces netdev_alloc_frag() for drivers willing to
use build_skb() instead of __netdev_alloc_skb() variants.
Factorize code so that :
__dev_alloc_skb() is a wrapper around __netdev_alloc_skb(), and
dev_alloc_skb() a wrapper around netdev_alloc_skb()
Use __GFP_COLD flag.
Almost all network drivers now benefit from skb->head_frag
infrastructure.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge reason: We are going to queue up a dependent patch:
"perf tools: Move parse event automated tests to separated object"
That depends on:
commit e7c72d8
perf tools: Add 'G' and 'H' modifiers to event parsing
Conflicts:
tools/perf/builtin-stat.c
Conflicted with the recent 'perf_target' patches when checking the
result of perf_evsel open routines to see if a retry is needed to cope
with older kernels where the exclude guest/host perf_event_attr bits
were not used.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Palmas is a PMIC from Texas Instruments and this is the MFD part of the
driver for this chip. The PMIC has SMPS and LDO regulators, a general
purpose ADC, GPIO, USB OTG mode detection, watchdog and RTC features.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This lets the kernel tell userspace if the device supports prime
import/export.
This is useful for -modesetting at least, but would be nice for other
drivers.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
ipv6_opt_accepted() returns a bool, and can use const pointers
ipv6_addr_equal(), ipv6_addr_any(), ipv6_addr_loopback(),
ipv6_addr_orchid() return a bool.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- match() method returns a boolean
- return (A && B && C && D) -> return A && B && C && D
- fix indentation
Signed-off-by: Eric Dumazet <edumazet@google.com>
More spring cleaning!
The ancient Econet protocol should go. Most of the bug fixes in recent
years have been fixing security vulnerabilities. The hardware hasn't
been made since the 90s, it is only interesting as an archeological curiosity.
For the truly curious, or insomniac, go read up on it.
http://en.wikipedia.org/wiki/Econet
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently qemu/kvm on s390 uses a guest mapping that does not
allow the guest backing page table to be write-protected to
support older systems. On those older systems a host write
protection fault will be delivered to the guest.
Newer systems allow to write-protect the guest backing memory
and let the fault be delivered to the host, thus allowing COW.
Use a capability bit to tell qemu if that is possible.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Hardware with MCA bus is limited to 386 and 486 class machines
that are now 20+ years old and typically with less than 32MB
of memory. A quick search on the internet, and you see that
even the MCA hobbyist/enthusiast community has lost interest
in the early 2000 era and never really even moved ahead from
the 2.4 kernels to the 2.6 series.
This deletes anything remaining related to CONFIG_MCA from core
kernel code and from the x86 architecture. There is no point in
carrying this any further into the future.
One complication to watch for is inadvertently scooping up
stuff relating to machine check, since there is overlap in
the TLA name space (e.g. arch/x86/boot/mca.c).
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: x86@kernel.org
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The support for CONFIG_MCA is being removed, since the 20
year old hardware simply isn't capable of meeting today's
software demands on CPU and memory resources.
This commit removes the MCA specific 8250 UART code.
Cc: Alan Cox <alan@linux.intel.com>
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enable dynamic debugging and remove a bunch of #ifdef/#endifs.
Add a lapb_dbg(level, fmt, ...) macro and replace the
printk(KERN_DEBUG uses.
Add pr_fmt and remove embedded prefixes.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is V2 of the Emma Mobile GPIO driver. This
driver is designed to be reusable between multiple SoCs
that share the same basic building block, but so far it
has only been used on Emma Mobile EV2.
Each driver instance handles 32 GPIOs with individually
maskable IRQs. The driver operates on two I/O memory
ranges and the 32 GPIOs are hooked up to two interrupts.
In the case of Emma Mobile EV2 this GPIO building block
is used as main external interrupt controller hooking up
159 GPIOS as 159 interrupts via 5 driver instances and
10 interrupts to the GIC and the Cortex-A9 Dual.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The padding destination or hop-by-hop option is called Pad1 and not Pad0.
See RFC2460 (4.2) or the IANA ipv6-parameters registry:
http://www.iana.org/assignments/ipv6-parameters/ipv6-parameters.xml
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some minor problems in comments of etherdevice.h
* Warning is out dated, file hasn't moved or disappeared in many years and
is unlikely to do so soon.
* Capitalize Ethernet consistently since it is a proper name
* Fix descriptive comment of padding
* Spelling and grammar fix for alignment comment
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bool conversions where possible.
__inline__ -> inline
space cleanups
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'd like to see the system waking up from the system-wide suspend
when it gets plugged-in, or the USB cable is pulled out.
Also makes it configurable via platform data 'wakeup'.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull perf, x86 and scheduler updates from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tracing: Do not enable function event with enable
perf stat: handle ENXIO error for perf_event_open
perf: Turn off compiler warnings for flex and bison generated files
perf stat: Fix case where guest/host monitoring is not supported by kernel
perf build-id: Fix filename size calculation
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, kvm: KVM paravirt kernels don't check for CPUID being unavailable
x86: Fix section annotation of acpi_map_cpu2node()
x86/microcode: Ensure that module is only loaded on supported Intel CPUs
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix KVM and ia64 boot crash due to sched_groups circular linked list assumption
This is now straightforward: just introduce a module parameter and pass
the needed value to persistent_ram_new().
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Marco Stornelli <marco.stornelli@gmail.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a first step for adding ECC support for pstore RAM backend: we
will use the persistent_ram routines, kindly provided by Google.
Basically, persistent_ram is a set of helper routines to deal with the
[optionally] ECC-protected persistent ram regions.
A bit of Makefile, Kconfig and header files adjustments were needed
because of the move.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That old mail address doesnt exist any more.
This changes all occurences to my new address.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rather than passing a bunch of arguments to be filled in with the
content of the ceph_auth_handshake buffer now returned by the
get_authorizer method, just use the returned information in the
caller, and drop the unnecessary arguments.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Have the get_authorizer auth_client method return a ceph_auth
pointer rather than an integer, pointer-encoding any returned
error value. This is to pave the way for making use of the
returned value in an upcoming patch.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Make use of the new ceph_auth_handshake structure in order to reduce
the number of arguments passed to the create_authorizor method in
ceph_auth_client_ops. Use a local variable of that type as a
shorthand in the get_authorizer method definitions.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
The definitions for the ceph_mds_session and ceph_osd both contain
five fields related only to "authorizers." Encapsulate those fields
into their own struct type, allowing for better isolation in some
upcoming patches.
Fix the #includes in "linux/ceph/osd_client.h" to lay out their more
complete canonical path.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
It's been broken forever (i.e. it's not scheduling in a power
aware fashion), as reported by Suresh and others sending
patches, and nobody cares enough to fix it properly ...
so remove it to make space free for something better.
There's various problems with the code as it stands today, first
and foremost the user interface which is bound to topology
levels and has multiple values per level. This results in a
state explosion which the administrator or distro needs to
master and almost nobody does.
Furthermore large configuration state spaces aren't good, it
means the thing doesn't just work right because it's either
under so many impossibe to meet constraints, or even if
there's an achievable state workloads have to be aware of
it precisely and can never meet it for dynamic workloads.
So pushing this kind of decision to user-space was a bad idea
even with a single knob - it's exponentially worse with knobs
on every node of the topology.
There is a proposal to replace the user interface with a single
3 state knob:
sched_balance_policy := { performance, power, auto }
where 'auto' would be the preferred default which looks at things
like Battery/AC mode and possible cpufreq state or whatever the hw
exposes to show us power use expectations - but there's been no
progress on it in the past many months.
Aside from that, the actual implementation of the various knobs
is known to be broken. There have been sporadic attempts at
fixing things but these always stop short of reaching a mergable
state.
Therefore this wholesale removal with the hopes of spurring
people who care to come forward once again and work on a
coherent replacement.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1326104915.2442.53.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Changelog v3:
- use __u64 instead of pointer in ioctl struct.
The G2D is a 2D graphic accelerator that supports Bit Block Transfer.
This G2D driver is exynos drm specific and supports only G2D(version
4.1) of later Exynos series from Exynos4X12 because supporting DMA.
The G2D is performed by two tasks simply.
1. Configures the rendering parameters, such as foreground color and
coordinates data by setting the drawing context registers.
2. Start the rendering process by setting thre relevant command
registers accordingly.
The G2D version 4.1 supports DMA mode as host interface. User can make
command list to reduce HOST(ARM) loads. The contents of The command list
is setted to relevant registers of G2D by DMA.
The command list is composed Header and command sets and Tail.
- Header: The number of command set(4Bytes)
- Command set: Register offset(4Bytes) + Register data(4Bytes)
- Tail: Pointer of base address of the other command list(4Bytes)
By Tail field, the G2D can process many command lists without halt at
one go.
The G2D has following the rendering pipeline.
--> Primitive Drawing --> Rotation --> Clipping --> Bilinear Sampling
--> Color Key --> ROP --> Mask Operation --> Alpha Blending -->
Dithering --> FrameBuffer
And supports various operations from the rendering pipeline.
- copy
- fast solid color fill
- window clipping
- rotation
- flip
- 4 operand raster operation(ROP4)
- masking operation
- alpha blending
- color key
- dithering
- etc
User should make the command list to data and registers needed by
operation to use. The Exynos G2D driver only manages the command lists
received from user. Some registers needs memory base address(physical
address) of image. User doesn't know its physical address, so fills the
gem handle of that memory than address to command sets, then G2D driver
converts it to memory base address.
We adds three ioctls and one event for Exynos G2D.
- ioctls
DRM_EXYNOS_G2D_GET_VER: get the G2D hardware version
DRM_EXYNOS_G2D_SET_CMDLIST: set the command list from user to driver
DRM_EXYNOS_G2D_EXEC: execute the command lists setted to driver
- event
DRM_EXYNOS_G2D_EVENT: event to give notification completion of the
command list to user
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The i915 driver needs this for the rotation and overscan compensation
properties. Other drivers might need this too.
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This way, we don't need to count every time, so we're a little bit
faster and code is a little bit smaller.
Change suggested by Ville Syrjälä.
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Useless for connector properties (since they already have their own
ioctls), but useful when we add properties to CRTCs, planes and other
objects.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For now, only connectors have it. In the future, all objects that need
properties should use it. Since the structure is referenced inside
struct drm_mode_object, we will be able to deal with object properties
without knowing the real type of the object.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also return void instead of int. We have more than 100 callers and
no one checks for the return value.
If this function fails the property won't be exposed by the get/set
ioctls, but we should probably survive. If this starts happening,
the solution will be to increase DRM_CONNECTOR_MAX_PROPERTY and
recompile the Kernel.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
bool/const conversions where possible
__inline__ -> inline
space cleanups
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ALUA MI_REPORT_TARGET_PGS extended header
format defined within SPC-4. It changes target core ALUA emulation logic
within target_emulate_report_target_port_groups() to support both the
extended and original length only header formats.
It includes adding a new 'implict_trans_secs' attribute for each ALUA
target port group to control the value returned to the application client
for an recommended implict translation timeout in seconds. By default
this value is currently set to zero, and limited up to 255 by virtue of
using a single byte in the extended header format.
This value is used by target_emulate_report_target_port_groups() within
the extended header logic to set IMPLICIT TRANSITION TIME as defined by
spc4r30.
Cc: Hannes Reinecke <hare@suse.de>
Cc: Rob Evers <revers@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
To remove duplicate code, have the ftrace arch_ftrace_update_code()
use the generic ftrace_modify_all_code(). This requires that the
default ftrace_replace_code() becomes a weak function so that an
arch may override it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Rename __ftrace_modify_code() to ftrace_modify_all_code() and make
it global for all archs to use. This will remove the duplication
of code, as archs that can modify code without stop_machine()
can use it directly outside of the stop_machine() call.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
ftrace_location() is passed an addr, and returns 1 if the addr is
on a ftrace nop (or caller to ftrace_caller), and 0 otherwise.
To let kprobes know if it should move a breakpoint or not, it
must return the actual addr that is the start of the ftrace nop.
This way a kprobe placed on the location of a ftrace nop, can
instead be placed on the instruction after the nop. Even if the
probe addr is on the second or later byte of the nop, it can
simply be moved forward.
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Instead of just sorting the ip's of the functions per ftrace page,
sort the entire list before adding them to the ftrace pages.
This will allow the bsearch algorithm to be sped up as it can
also sort by pages, not just records within a page.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Large timeout parameters could result wrong timeout values due to
an overflow at msec to jiffies conversion (reported by Andreas Herz)
[ This patch was mangled by Pablo Neira Ayuso since David Laight and
Eric Dumazet noticed that we were using hardcoded 1000 instead of
MSEC_PER_SEC to calculate the timeout ]
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David Miller says:
The canonical way to validate if the set bits are in a valid
range is to have a "_ALL" macro, and test:
if (val & ~XT_HASHLIMIT_ALL)
goto err;"
make it so.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking tree from David Miller:
1) ptp_pch driver build broke during this merge window due to missing
slab.h header, fix from Geery Uytterhoeven.
2) If ipset passes in a bogus hash table size we crash because the size
is not validated properly. Compounding this, gcc-4.7 can miscompile
ipset such that even when the user specifies legitimate parameters
the tool passes in an out-of-range size to the kernel.
Fix from Jozsef Kadlecsik.
3) Users have reported that the netdev watchdog can trigger with pch_gbe
devices, and it turns out this is happening because of races in the
TX path of the driver leading to the transmitter hanging. Fix from
Eric Dumazet, reported and tested by Andy Cress.
4) Novatel USB551L devices match the generic class entries for the cdc
ethernet USB driver, but they don't work because they have generic
descriptors and thus need FLAG_WWAN to function properly.
Add the necessary ID table entry to fix this, from Dan Williams.
5) A recursive locking fix in the USBNET driver added a new problem, in
that packet list traversal is now racy and we can thus access
unlinked SKBs and crash.
Avoid this situation by adding some extra state tracking, from Ming
Lei.
6) The rtlwifi conversion to asynchronous firmware loading is racy, fix
by reordering the probe procedure. From Larry Finger.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=43187
7) Fix regressions with bluetooth keyboards by notifying userland
properly when the security level changes, from Gustavo Padovan.
8) Bluetooth needs to make sure device connected events are emitted
before other kinds of events, otherwise userspace will think there is
no baseband link yet and therefore abort the sockets associated with
that connection.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
netfilter: ipset: fix hash size checking in kernel
ptp_pch: Add missing #include <linux/slab.h>
pch_gbe: fix transmit races
cdc_ether: add Novatel USB551L device IDs for FLAG_WWAN
usbnet: fix skb traversing races during unlink(v2)
Bluetooth: mgmt: Fix device_connected sending order
Bluetooth: notify userspace of security level change
rtlwifi: fix for race condition when firmware is cached
The hash size must fit both into u32 (jhash) and the max value of
size_t. The missing checking could lead to kernel crash, bug reported
by Seblu.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- sock_flag() accepts a const pointer
- sock_flag() returns a boolean
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
codel_should_drop() logic allows a packet being not dropped if queue
size is under max packet size.
In fq_codel, we have two possible backlogs : The qdisc global one, and
the flow local one.
The meaningful one for codel_should_drop() should be the global backlog,
not the per flow one, so that thin flows can have a non zero drop/mark
probability.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Kathleen Nichols <nichols@pollere.com>
Cc: Van Jacobson <van@pollere.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MISDN_CTRL_RX_OFF is a meachanism to discard RX data in the driver if
the data is not needed by the application. It can be used when playing
mesages, but not recording or with unidirectional protocols.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
MISDN_CTRL_FILL_EMPTY is a meachanism to send a fixed value (normally silence)
as long no data from upper layers is available. It can be used when recording
voice messages or with unidirectional protocols.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the FIFO of the card is small, many short messages are queued up to
the upper layers and the userspace. This change allows the applications
to set a minimum datalen they want from the drivers.
Create a common control function to avoid code duplication in each
driver.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We did allways allocate maxsize buffers, but for transparent data we know
the actual size.
Use a common function to calculate size and detect overflows.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is better to send a confirm for transparent data early as possible
to avoid TX underuns.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for monitor device intended to capture all the network activity.
This interface could be used by networks sniffers and is already
supported by WireShark. That's a good test point to check that basic
MAC support works.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This stack implementation distinguishes several types of slave
interfaces. Another parameter to 'add_iface_' function is added
to clarify the interface type is going to be registered.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According IEEE 802.15.4 standard each node can be either full functionality
device (FFD) or reduce functionality device (RFD). So 2 sets of operations
are needed. This patch declare RFD operations structure.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Main RX data path implementation between physical and mac layers.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An interface to allocate and register ieee802154 compatible device.
The allocated device has the following representation in memory:
+-----------------------+
| struct wpan_phy |
+-----------------------+
| struct mac802154_priv |
+-----------------------+
| driver's private data |
+-----------------------+
Used by device drivers to register new instance in the stack.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IEEE 802.15.4 Working Group focuses on the standardization of the
bottom two layers of ISO/OSI protocol stack: Physical (PHY) and MAC.
The MAC layer provides access control to a shared channel and reliable
data delivery. The main functions performed by the MAC sublayer are:
association and disassociation, security control, optional star
network topology functions, such as beacon generation and Guaranteed
Time Slots (GTSs) management, generation of ACK frames (if used), and,
finally, application support for the two possible network topologies
described in the standard.
This is an initial commit which describes main data structures needed
for ieee802.15.4 compatible devices representation in the MAC layer.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
defer_setup and suspended are now flags into bt_sk().
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The ERTM and streaming mode transmit queue must only be accessed while
the L2CAP channel lock is held. Locking the channel before calling
l2cap_chan_send ensures that multiple threads cannot simultaneously
manipulate the queue when sending and receiving concurrently.
L2CAP channel locking had previously moved to the l2cap_chan struct
instead of the associated socket, so some of the old socket locking
can also be removed in this patch.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
The mgmt_device_found function expects to receive only the significant
part of the EIR data so it needs to be removed before calling the
function. This patch adds a new eir_get_length() helper function to
calculate the length of the significant part.
Signed-off-by: Vishal Agarwal <vishal.agarwal@stericsson.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Using RCU for lockless shadow walking can increase the amount of memory
in use by the system, since RCU grace periods are unpredictable. We also
have an unconditional write to a shared variable (reader_counter), which
isn't good for scaling.
Replace that with a scheme similar to x86's get_user_pages_fast(): disable
interrupts during lockless shadow walk to force the freer
(kvm_mmu_commit_zap_page()) to wait for the TLB flush IPI to find the
processor with interrupts enabled.
We also add a new vcpu->mode, READING_SHADOW_PAGE_TABLES, to prevent
kvm_flush_remote_tlbs() from avoiding the IPI.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
It should return bool, not int. The function even
does return true/false.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't really want/need to maintain the old
station flags API any more, so refuse changes
to new (not yet defined) flags from the old
flags API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The netlink commands and attributes, along with the socket structure
definitions need to be exported.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a flag for the HT format (mixed vs. greenfield)
to allow drivers to report that on receive. Not all
drivers will do that though, so allow drivers to set
which radiotap MCS details they report.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add IV-room in skb also for TKIP and WEP.
Extend patch: "mac80211: support adding IV-room in the skb for CCMP keys"
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is based on code from pcie_misc_config_fixup() in brcmsmac.
This patch is part of the move of pci specific code from brcmsmac to
bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is based on code from pcicore_fixcfg() in brcmsmac. This
patch is part of the move of pci specific code from brcmsmac to bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is based on code from pcie_extendL1timer() in brcmsmac. This
patch is part of the move of pci specific code from brcmsmac to bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These newly added attributes are used by brcmsmac. Now bcma should
parse all attributes used by brcmsmac out of the sprom.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This attribute is now used in b43 driver and should be filled for all
sprom versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The attribute country_code and alpha2 are two different attributes in
the sprom. country_code contains some code in an 8 bit coding and
alpha2 contains two chars with the country code. The attributes where
read out wrongly in the past and country_code is only available on
sprom version 1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This struct contains information about the board, the chip is running
on. The struct is filled for PCIe devices and SoCs. This information is
used by b43 and will be used by brcmsmac soon.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the rev contained the revision read from the pci config
space and was used as board_rev in the wireless drivers. This is wrong
the board_rev is only fetched from the sprom accordingly to the open
source part of the Broadcom SDK and brcmsmac. This patch removes the
rev from the boardinfo structure and uses the board_rev attribute from
sprom instead. This attribute is filled by PCI, PCMCIA, SDIO and SoC
code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since ramoops was converted to pstore, it has nothing to do with character
devices nowadays. Instead, today it is just a RAM backend for pstore.
The patch just moves things around. There are a few changes were needed
because of the move:
1. Kconfig and Makefiles fixups, of course.
2. In pstore/ram.c we have to play a bit with MODULE_PARAM_PREFIX, this
is needed to keep user experience the same as with ramoops driver
(i.e. so that ramoops.foo kernel command line arguments would still
work).
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Marco Stornelli <marco.stornelli@gmail.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* 'clk-next' of git://git.linaro.org/people/mturquette/linux:
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
ARM: Orion: SDIO: Add support for clk.
ARM: Orion: NAND: Add support for clk, if there is one.
ARM: Orion: EHCI: Add support for enabling clocks
ARM: Orion: SATA: Add per channel clk/clkdev support.
ARM: Orion: UART: Get the clock rate via clk_get_rate().
ARM: Orion: WDT: Add clk/clkdev support
ARM: Orion: Eth: Add clk/clkdev support.
ARM: Orion: SPI: Add clk/clkdev support.
ARM: Orion: Add clocks using the generic clk infrastructure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
John Linville says:
Here are three more fixes that some of my developers are desperate to
see included in 3.4...
Johan Hedberg went to some length justifyng the inclusion of these two
Bluetooth fixes:
"The device_connected fix should be quite self-explanatory, but it's
actually a wider issue than just for keyboards. All profiles that do
incoming connection authorization (e.g. headsets) will break without it
with specific hardware. The reason it wasn't caught earlier is that it
only occurs with specific Bluetooth adapters.
As for the security level patch, this fixes L2CAP socket based security
level elevation during a connection. The HID profile needs this (for
keyboards) and it is the only way to achieve the security level
elevation when using the management interface to talk to the kernel
(hence the management enabling patch being the one that exposes this"
The rtlwifi fix addresses a regression related to firmware loading,
as described in kernel.org bug 43187. It basically just moves a hunk
of code to a more appropriate place.
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is only referenced from within phy_device.c, so there is
no reason to export it. In fact, we can make it static.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This represents the mass deletion of the of the tokenring support.
It gets rid of:
- the net/tr.c which the drivers depended on
- the drivers/net component
- the Kbuild infrastructure around it
- any tokenring related CONFIG_ settings in any defconfigs
- the tokenring headers in the include/linux dir
- the firmware associated with the tokenring drivers.
- any associated token ring documentation.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We are going to delete the Token ring support. This removes any
special processing in the core networking for token ring, (aside
from net/tr.c itself), leaving the drivers and remaining tokenring
support present but inert.
The mass removal of the drivers and net/tr.c will be in a separate
commit, so that the history of these files that we still care
about won't have the giant deletion tied into their history.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The callback is now hooked up for any USB to serial driver that wants
it. We only register the callback if any of the usb-serial structures
want it, this keeps the USB core happy.
Thanks to Alan Stern for the ideas on how to do this.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If journal superblock is written only in disk's caches and other transaction
starts reusing space of the transaction cleaned from the log, it can happen
blocks of a new transaction reach the disk before journal superblock. When
power failure happens in such case, subsequent journal replay would still try
to replay the old transaction but some of it's blocks may be already
overwritten by the new transaction. For this reason we must use WRITE_FUA when
updating log tail and we must first write new log tail to disk and update
in-memory information only after that.
Signed-off-by: Jan Kara <jack@suse.cz>
There are three case of updating journal superblock. In the first case, we want
to mark journal as empty (setting s_sequence to 0), in the second case we want
to update log tail, in the third case we want to update s_errno. Split these
cases into separate functions. It makes the code slightly more straightforward
and later patches will make the distinction even more important.
Signed-off-by: Jan Kara <jack@suse.cz>
The NFC core code already does that for them.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an NFC driver for NXP pn544.
Unlike pn544.c, this one is based on the NFC HCI and SHDLC kernel layers.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is now specified that nfc_target_found() and nfc_target_lost() core
functions must not be called from an atomic context. This allow us to
serialize calls and protect the targets table using the nfc device lock
instead of a spinlock.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The NFC Core now caches the active nfc target pointer, thereby avoiding
the need to lookup the target table for each invocation of a driver ops.
Consequently, pn533, HCI and NCI now directly receive an nfc_target
pointer instead of a target index.
Cc: Ilan Elias <ilane@ti.com>
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Store uids and gids with kuid_t and kgid_t in struct kstat
- Convert uid and gids to userspace usable values with
from_kuid and from_kgid
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Add a capabilities field to the soc_camera_host structure to flag hosts
that support user-configurable line strides. soc_camera_try_fmt() then
passes the user-provided bytesperline and sizeimage format fields to
such hosts, and expects the host to check (and fix if needed) the
values.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[g.liakhovetski@gmx.de: fix a typo in mx2_camera.c]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function returns the minimum size of an image for a given number of
bytes per line (as per the V4L2 specification), width and format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To compute the value of the v4l2_pix_format::bytesperline field, we need
information about planes layout for planar formats. The new enum
soc_mbus_layout conveys that information.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While there's no actual implementation behind it having the call to use
in drivers makes them feel neater from a driver author point of view. An
actual implementation can wait for someone who needs to use the function
in a real system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[mturquette@linaro.org: void return type instead of int -EINVAL]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Take advantage of the new regmap irq_domain support to dynamically
allocate interrupts, using regmap_irq_get_virq() rather than irq_base
to look up the interrupts. This means that most users should not need
to specify an irq_base at all.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
__ratelimit() can be considered an inverted bool test because
it returns true when not ratelimited. Several tests in the
kernel tree use this __ratelimit() function incorrectly.
No net_ratelimit uses are incorrect currently though.
Most uses of net_ratelimit are to log something via printk or
pr_<level>.
In order to minimize the uses of net_ratelimit, and to start
standardizing the code style used for __ratelimit() and net_ratelimit(),
add a net_ratelimited_function() macro and net_<level>_ratelimited()
logging macros similar to pr_<level>_ratelimited that use the global
net_ratelimit instead of a static per call site "struct ratelimit_state".
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4231d47e6fe69f061f96c98c30eaf9fb4c14b96d(net/usbnet: avoid
recursive locking in usbnet_stop()) fixes the recursive locking
problem by releasing the skb queue lock before unlink, but may
cause skb traversing races:
- after URB is unlinked and the queue lock is released,
the refered skb and skb->next may be moved to done queue,
even be released
- in skb_queue_walk_safe, the next skb is still obtained
by next pointer of the last skb
- so maybe trigger oops or other problems
This patch extends the usage of entry->state to describe 'start_unlink'
state, so always holding the queue(rx/tx) lock to change the state if
the referd skb is in rx or tx queue because we need to know if the
refered urb has been started unlinking in unlink_urbs.
The other part of this patch is based on Huajun's patch:
always traverse from head of the tx/rx queue to get skb which is
to be unlinked but not been started unlinking.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
o flag field of ethtool_dump structure must be initialized by this macro
value that is zero, if the firmware dump is disabled.
by this we can get the firmware dump capability [enable/disable] via ethtool
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch, 2of4, contains the changes to the core swap subsystem.
This includes:
(1) makes available core swap data structures (swap_lock, swap_list and
swap_info) that are needed by frontswap.c but we don't need to expose them
to the dozens of files that include swap.h so we create a new swapfile.h
just to extern-ify these and modify their declarations to non-static
(2) adds frontswap-related elements to swap_info_struct. Frontswap_map
points to vzalloc'ed one-bit-per-swap-page metadata that indicates
whether the swap page is in frontswap or in the device and frontswap_pages
counts how many pages are in frontswap.
(3) adds hooks in the swap subsystem and extends try_to_unuse so that
frontswap_shrink can do a "partial swapoff".
Note that a failed frontswap_map allocation is safe... failure is noted
by lack of "FS" in the subsequent printk.
---
[v14: rebase to 3.4-rc2]
[v10: no change]
[v9: akpm@linux-foundation.org: mark some statics __read_mostly]
[v9: akpm@linux-foundation.org: add clarifying comments]
[v9: akpm@linux-foundation.org: no need to loop repeating try_to_unuse]
[v9: error27@gmail.com: remove superfluous check for NULL]
[v8: rebase to 3.0-rc4]
[v8: kamezawa.hiroyu@jp.fujitsu.com: change counter to atomic_t to avoid races]
[v8: kamezawa.hiroyu@jp.fujitsu.com: comment to clarify informational counters]
[v7: rebase to 3.0-rc3]
[v7: JBeulich@novell.com: add new swap struct elements only if config'd]
[v6: rebase to 3.0-rc1]
[v6: lliubbo@gmail.com: fix null pointer deref if vzalloc fails]
[v6: konrad.wilk@oracl.com: various checks and code clarifications/comments]
[v5: no change from v4]
[v4: rebase to 2.6.39]
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Reviewed-by: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Jan Beulich <JBeulich@novell.com>
Acked-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Rik Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
[v11: Rebased, fixed mm/swapfile.c context change]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Frontswap is the alter ego of cleancache, the "yang" to cleancache's
"yin"... and more precisely frontswap is the provider of anonymous
pages to transcendent memory to nicely complement cleancache's providing
of clean pagecache pages to transcendent memory. For optimal use
of transcendent memory, both are necessary... because a kernel
under memory pressure first reclaims clean pagecache pages and,
when under more memory pressure, starts swapping anonymous pages.
Frontswap and cleancache (which was merged at 3.0) are the "frontends"
and the only necessary changes to the core kernel for transcendent memory;
all other supporting code -- the "backends" -- is implemented as drivers.
See the LWN.net article "Transcendent memory in a nutshell" for a detailed
overview of frontswap and related kernel parts:
https://lwn.net/Articles/454795/
Frontswap code was first posted publicly in January 2009 and on LKML in
May 2009, and has remained functionally stable for nearly three years now.
It is barely invasive, touching only the swap subsystem and adds less
than 100 lines of code to existing swap subsystem code files.
It has improved syntactically substantially between V1 and this posting
of V14, thanks to the review of a few kernel developers, and has adapted
easily to at least one major swap subsystem change. As of 3.4, there are
three in-tree users of frontswap patiently waiting for this patchset and
for CONFIG_FRONTSWAP to be enabled: zcache (staging driver merged at
2.6.39), Xen tmem (merged at 3.0 and 3.1) and RAMster (staging driver
merged at 3.4). In addition, a RFC has been posted for a KVM backend.
The frontswap patchset has been in linux-next since next-110603. Earlier
versions of frontswap already ship in the Oracle Unbreakable Enterprise Kernel
and SuSE SLES.
This patch, 1of4, provides the header file for the core code for frontswap
that interfaces between the hooks in the swap subsystem and a frontswap
backend via frontswap_ops.
---
New file added: include/linux/frontswap.h
[v14: add support for writethrough, per suggestion by aarcange@redhat.com]
[v14: rebase to 3.4-rc2]
[v11: konrad.wilk@oracle.com: squashed s/flush/invalidate/ in]
[v10: no change]
[v9: akpm@linux-foundation.org: change "flush" to "invalidate", part 1]
[v8: rebase to 3.0-rc4]
[v7: rebase to 3.0-rc3]
[v7: JBeulich@novell.com: new static inlines resolve to no-ops if not config'd]
[v7: JBeulich@novell.com: avoid redundant shifts/divides for *_bit lib calls]
[v6: rebase to 3.1-rc1]
[v5: no change from v4]
[v4: rebase to 2.6.39]
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Jan Beulich <JBeulich@novell.com>
Acked-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Rik Riel <riel@redhat.com>
[v15: int/bool on some functions]
Signed-off-by: Konrad Wilk <konrad.wilk@oracle.com>
Under memory load, on x86_64, with lockdep enabled, the workqueue's
process_one_work() has been seen to oops in __lock_acquire(), barfing
on a 0xffffffff00000000 pointer in the lockdep_map's class_cache[].
Because it's permissible to free a work_struct from its callout function,
the map used is an onstack copy of the map given in the work_struct: and
that copy is made without any locking.
Surprisingly, gcc (4.5.1 in Hugh's case) uses "rep movsl" rather than
"rep movsq" for that structure copy: which might race with a workqueue
user's wait_on_work() doing lock_map_acquire() on the source of the
copy, putting a pointer into the class_cache[], but only in time for
the top half of that pointer to be copied to the destination map.
Boom when process_one_work() subsequently does lock_map_acquire()
on its onstack copy of the lockdep_map.
Fix this, and a similar instance in call_timer_fn(), with a
lockdep_copy_map() function which additionally NULLs the class_cache[].
Note: this oops was actually seen on 3.4-next, where flush_work() newly
does the racing lock_map_acquire(); but Tejun points out that 3.4 and
earlier are already vulnerable to the same through wait_on_work().
* Patch orginally from Peter. Hugh modified it a bit and wrote the
description.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Reported-by: Hugh Dickins <hughd@google.com>
LKML-Reference: <alpine.LSU.2.00.1205070951170.1544@eggly.anvils>
Signed-off-by: Tejun Heo <tj@kernel.org>
Don't bother checking for NULL key pointer in key_validate() as all of the
places that call it will crash anyway if the relevant key pointer is NULL by
the time they call key_validate(). Therefore, the checking must be done prior
to calling here.
Whilst we're at it, simplify the key_validate() function a bit and mark its
argument const.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Use "enum_framesizes" instead of "enum_fsizes" to more precisely follow
the name of the respective ioctl().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Sergio Aguirre <sergio.a.aguirre@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the V4L2_EVENT_SUB_FL_SEND_INITIAL was set, then the application expects
to receive an initial event of the initial value of the control.
However, commit c53c254933 that added the new
v4l2_subscribed_event_ops introduced a regression: while the code still queued
that initial event the __v4l2_event_queue_fh() function was modified to ignore
such requests if sev->elems was 0 (meaning that the event subscription wasn't
finished yet).
And sev->elems was only set to a non-zero value after the add operation
returned.
This patch fixes this by passing the elems value to the add function. Then the
add function can set it before queuing the initial event.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* linus/master: (805 commits)
tty: Fix LED error return
openvswitch: checking wrong variable in queue_userspace_packet()
bonding: Fix LACPDU rx_dropped commit.
Linux 3.4-rc7
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
MAINTAINERS: Add myself as the cpufreq maintainer
dm mpath: check if scsi_dh module already loaded before trying to load
dm thin: correct module description
dm thin: fix unprotected use of prepared_discards list
dm thin: reinstate missing mempool_free in cell_release_singleton
gpio/exynos: Fix compiler warnings when non-exynos machines are selected
gpio: pch9: Use proper flow type handlers
powerpc/irq: Fix another case of lazy IRQ state getting out of sync
ks8851: Update link status during link change interrupt
...
Conflicts:
drivers/media/common/tuners/xc5000.c
drivers/media/common/tuners/xc5000.h
drivers/usb/gadget/uvc_queue.c
* 'kirkwood_boards_for_v3.5' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
kirkwood: Add iconnect support
orion/kirkwood: create a generic function for gpio led blinking
kirkwood/orion: fix orion_gpio_set_blink
ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
kirkwood: Allow nand to be configured via. devicetree
mtd: Add orion_nand devicetree bindings
ARM: kirkwood: Basic support for DNS-320 and DNS-325
Includes an update to v3.4-rc7
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
6d1d8050b4 "block, partition: add partition_meta_info to hd_struct"
added part_unpack_uuid() which assumes that the passed in buffer has
enough space for sprintfing "%pU" - 37 characters including '\0'.
Unfortunately, b5af921ec0 "init: add support for root devices
specified by partition UUID" supplied 33 bytes buffer to the function
leading to the following panic with stackprotector enabled.
Kernel panic - not syncing: stack-protector: Kernel stack corrupted in: ffffffff81b14c7e
[<ffffffff815e226b>] panic+0xba/0x1c6
[<ffffffff81b14c7e>] ? printk_all_partitions+0x259/0x26xb
[<ffffffff810566bb>] __stack_chk_fail+0x1b/0x20
[<ffffffff81b15c7e>] printk_all_paritions+0x259/0x26xb
[<ffffffff81aedfe0>] mount_block_root+0x1bc/0x27f
[<ffffffff81aee0fa>] mount_root+0x57/0x5b
[<ffffffff81aee23b>] prepare_namespace+0x13d/0x176
[<ffffffff8107eec0>] ? release_tgcred.isra.4+0x330/0x30
[<ffffffff81aedd60>] kernel_init+0x155/0x15a
[<ffffffff81087b97>] ? schedule_tail+0x27/0xb0
[<ffffffff815f4d24>] kernel_thread_helper+0x5/0x10
[<ffffffff81aedc0b>] ? start_kernel+0x3c5/0x3c5
[<ffffffff815f4d20>] ? gs_change+0x13/0x13
Increase the buffer size, remove the dangerous part_unpack_uuid() and
use snprintf() directly from printk_all_partitions().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Szymon Gruszczynski <sz.gruszczynski@googlemail.com>
Cc: Will Drewry <wad@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In mixed burst (MB) mode, the AHB master always initiates
the bursts with fixed-size when the DMA requests transfers
of size less than or equal to 16 beats.
This patch adds the MB support and the flag that can be
passed from the platform to select it.
MB mode can also give some benefits in terms of performances
on some platforms.
v2: fixed Coding Style
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David pointed out gcc might generate poor code with 31bit fields.
Using u16 is more than enough and permits a better code output.
Also make the code intent more readable using constants, fixed point arithmetic
not being trivial for everybody.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove percpu_xxx serial functions, all of them were replaced by
this_cpu_xxx or __this_cpu_xxx serial functions
Signed-off-by: Alex Shi <alex.shi@intel.com>
Acked-by: Christoph Lameter <cl@gentwo.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since percpu_xxx() serial functions are duplicated with this_cpu_xxx().
Removing percpu_xxx() definition and replacing them by this_cpu_xxx()
in code. There is no function change in this patch, just preparation for
later percpu_xxx serial function removing.
On x86 machine the this_cpu_xxx() serial functions are same as
__this_cpu_xxx() without no unnecessary premmpt enable/disable.
Thanks for Stephen Rothwell, he found and fixed a i386 build error in
the patch.
Also thanks for Andrew Morton, he kept updating the patchset in Linus'
tree.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Acked-by: Christoph Lameter <cl@gentwo.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds a helper function for retriving a iio_dev struct from a device
struct. Currently we open-code this in two different ways. One is using
dev_get_drvdata on the device and the other is using container_of. The new
helper function uses the container_of solution as it creates slightly smaller
code and also will eventually free up the drvdata pointer for usage by invidual
drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AT91 SoCs often embeds an ADC. This patch adds the needed
platform data to specify the informations required by the driver
to work properly.
For now, we only need the reference voltage and which channels
are available on the board.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* 'dt' of git://github.com/hzhuang1/linux:
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
Includes an update to v3-4-rc5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch (as1554) fixes a lockdep false-positive report. The
problem arises because lockdep is unable to deal with the
tree-structured locks created by the device core and sysfs.
This particular problem involves a sysfs attribute method that
unregisters itself, not from the device it was called for, but from a
descendant device. Lockdep doesn't understand the distinction and
reports a possible deadlock, even though the operation is safe.
This is the sort of thing that would normally be handled by using a
nested lock annotation; unfortunately it's not feasible to do that
here. There's no sensible way to tell sysfs when attribute removal
occurs in the context of a parent attribute method.
As a workaround, the patch adds a new flag to struct attribute
telling sysfs not to inform lockdep when it acquires a readlock on a
sysfs_dirent instance for the attribute. The readlock is still
acquired, but lockdep doesn't know about it and hence does not
complain about impossible deadlock scenarios.
Also added are macros for static initialization of attribute
structures with the ignore_lockdep flag set. The three offending
attributes in the USB subsystem are converted to use the new macros.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Tejun Heo <tj@kernel.org>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull media fixes from Mauro Carvalho Chehab:
"For a some fix patches for v3.4, including a regression fix at DVB core"
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] gspca - sonixj: Fix a zero divide in isoc interrupt
[media] media: videobuf2-dma-contig: include header for exported symbols
[media] media: videobuf2-dma-contig: quiet sparse noise about plain integer as NULL pointer
[media] media: vb2-memops: Export vb2_get_vma symbol
[media] s5p-fimc: Correct memory allocation for VIDIOC_CREATE_BUFS
[media] s5p-fimc: Fix locking in subdev set_crop op
[media] dvb_frontend: fix a regression with DVB-S zig-zag
[media] fintek-cir: change || to &&
[media] V4L: Schedule V4L2_CID_HCENTER, V4L2_CID_VCENTER controls for removal
[media] rc: Postpone ISR registration
[media] marvell-cam: fix an ARM build error
[media] V4L: soc-camera: protect hosts during probing from overzealous user-space
Rename the function v4l2_dont_use_lock to v4l2_disable_ioctl_locking,
and rename v4l2_dont_use_cmd to v4l2_disable_ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This flag is for legacy drivers only and will go away in the future.
A note regarding commit 5126f2590b
(v4l2-dev: add flag to have the core lock all file operations):
That commit message suggests that by not taking the core lock for fops
other than unlocked_ioctl all problems relating to AB-BA locking and
mm->mmap_sem are solved. This is not the case.
More work needs to be done by moving the core lock further down into
video_ioctl2. It should only be taken after the copy_from/to_user calls
are done.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The querycap ioctl returned an incorrect version number and incorrect
capabilities (mixing up vbi and video caps).
The reason for that was that video nodes could do vbi activities: that
should be separated between the vbi and video nodes.
There were also a few minor problems with dbg_g/s_register that have
been resolved. The mxb/saa7146 driver now passes the v4l2_compliance tests.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use v4l2_fh which gives you control events and priority handling for free.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was also a vbi_q and video_q in saa7146_fh, so that was confusing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This information can also be retrieved from struct video_device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fields are global and don't belong in a fh struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a global structure and does not belong to saa7146_fh.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is global information, not per-filehandle information.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert to the control framework, fix the easy v4l2-compliance failures.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It fixes L2CAP socket based security level elevation during a
connection. The HID profile needs this (for keyboards) and it is the only
way to achieve the security level elevation when using the management
interface to talk to the kernel (hence the management enabling patch
being the one that exposes this issue).
It enables the userspace a security level change when the socket is
already connected and create a way to notify the socket the result of the
request. At the moment of the request the socket is made non writable, if
the request fails the connections closes, otherwise the socket is made
writable again, POLL_OUT is emmited.
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The V4L2_CID_3A_LOCK bitmask control allows applications to pause
or resume the automatic exposure, focus and wite balance adjustments.
It can be used, for example, to lock the 3A adjustments right before
a still image is captured, for pre-focus, etc.
The applications can control each of the algorithms independently,
through a corresponding control bit, if driver allows that.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add control for the scene mode feature available in image sensor
with more advanced ISP firmware. The V4L2_CID_SCENE_MODE menu
control allows to select a set of parameters or a specific image
processing and capture control algorithm optimized for common
image capture conditions.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2_CID_EXPOSURE_METERING control allows to determine
a method used by the camera for measuring the amount of light
available for automatic exposure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add ISO sensitivity and ISO auto/manual controls. The sensitivity
values are related to level of amplification of the analog signal
between image sensor and ADC. These controls allow to support sensors
exposing an interface to accept the ISO values directly.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Given a large n, the bounds check (*p + n > end) can be bypassed due to
pointer wraparound. A safer check is (n > end - *p).
[elder@dreamhost.com: inverted test and renamed ceph_has_room()]
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Reviewed-by: Alex Elder <elder@dreamhost.com>
Add V4L2_CID_IMAGE_STABILIZATION control for the camera image
stabilization feature. This control can be used to enable/disable
image stabilization. It might get converted to a menu control
in future if more options are needed.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add V4L2_CID_WIDE_DYNAMIC_RANGE camera class control for the
camera wide dynamic range (WDR, HDR) feature. This control
can be used to enable/disable wide dynamic range. It might
get converted to a menu control in future if more options
are needed.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE control which is
an extended version of the V4L2_CID_AUTO_WHITE_BALANCE control,
including white balance presets. The following presets are defined:
- V4L2_WHITE_BALANCE_INCANDESCENT,
- V4L2_WHITE_BALANCE_FLUORESCENT,
- V4L2_WHITE_BALANCE_FLUORESCENT_H,
- V4L2_WHITE_BALANCE_HORIZON,
- V4L2_WHITE_BALANCE_DAYLIGHT,
- V4L2_WHITE_BALANCE_FLASH,
- V4L2_WHITE_BALANCE_CLOUDY,
- V4L2_WHITE_BALANCE_SHADE.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera may in some conditions incorrectly determine the exposure,
and a manual automatic exposure correction may be needed. This patch
adds V4L2_CID_AUTO_EXPOSURE_BIAS control which allows to add some
offset in the automatic exposure control loop, to compensate for
frame under- or over-exposure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds v4l2_ctrl_new_int_menu() helper function which can be used
in drivers for creating standard integer menu control with driver-specific
menu item list. It is similar to v4l2_ctrl_new_std_menu(), except it doesn't
have a mask parameter and an additional qmenu parameter allows passing
an array of signed 64-bit integers as the menu item list.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Tested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
