Defaulting to DEBUG_ICEDCC will cause systems to hang during boot unless
a hardware debugger is listening to the debug comms. channel.
This patch adds a dummy UART option as the default DEBUG_LL choice which
requires the platform to do the right thing.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
DEBUG_ICEDCC support is just another DEBUG_LL choice and
selecting it along with other DEBUG_LL options doesn't make
much sense. Put it into the DEBUG_LL choice to avoid confusion.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM patch 7072/1 (debug: use kconfig choice for selecting
DEBUG_LL UART) didn't notice that the Kconfigs relied on being
unselected to configure a different serial port. Since there is
no NONE option in a choice menu, explicitly add the other option
so that both serial ports can be selected.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enabled DEBUG_LL hardcodes the UART address into the kernel and results
in a non-portable kernel image. Since this option is only intended for
use when debugging early boot failures, supporting multiple platforms
in such a configuration is not the intended use-case.
This patch documents this limitation in the DEBUG_LL Kconfig help text,
so that users are aware of the portability restrictions that are associated
with enabling low-level debugging support.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enabling CONFIG_DEBUG_LL (which is required for earlyprintk) hardwires
the debug UART address into the kernel, so that we can print before the
platform is initialised.
If the user inadvertently selects multiple platforms with DEBUG_LL
enabled, the UART address may not be correct and will likely cause the
kernel to hang in the very early stages of boot.
This patch, based on a skeleton from Russell, uses a Kconfig choice for
selecting the DEBUG_LL UART, therefore allowing the user to make a
choice about the supported platform when DEBUG_LL is enabled.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The definition of __exception_irq_entry for
CONFIG_FUNCTION_GRAPH_TRACER=y needs linux/ftrace.h, but this creates a
circular dependency with it's current home in asm/system.h. Create
asm/exception.h and update all current users.
v4: - rebase to rmk/for-next
v3: - remove redundant includes of linux/ftrace.h
v2: - document the usage restricitions of __exception*
Cc: Zoltan Devai <zdevai@gmail.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In order to be able to handle localtimer directly from C code instead of
assembly code, introduce handle_local_timer(), which is modeled after
handle_IRQ().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In order to be able to handle IPI directly from C code instead of
assembly code, introduce handle_IPI(), which is modeled after handle_IRQ().
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When Cortex-A9 MPCore resumes from Dormant or Shutdown modes,
SCU needs to be re-enabled. This patch removes __init annotation
from function scu_enable(), so that platform resume procedure can
call it to re-enable SCU.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GIC driver must convert logical CPU numbers passed in from Linux
into physical CPU numbers that are understood by the hardware.
This patch uses the new cpu_logical_map macro for performing the
conversion inside the GIC driver.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To allow booting Linux on a CPU with physical ID != 0, we need to
provide a mapping from the logical CPU number to the physical CPU
number.
This patch adds such a mapping and populates it during boot.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The affinity between ARM processors is defined in the MPIDR register.
We can identify which processors are in the same cluster,
and which ones have performance interdependency. We can define the
cpu topology of ARM platform, that is then used by sched_mc and sched_smt.
The default state of sched_mc and sched_smt config is disable.
When enabled, the behavior of the scheduler can be modified with
sched_mc_power_savings and sched_smt_power_savings sysfs interfaces.
Changes since v4 :
* Remove unnecessary parentheses and blank lines
Changes since v3 :
* Update the format of printk message
* Remove blank line
Changes since v2 :
* Update the commit message and some comments
Changes since v1 :
* Update the commit message
* Add read_cpuid_mpidr in arch/arm/include/asm/cputype.h
* Modify header of arch/arm/kernel/topology.c
* Modify tests and manipulation of MPIDR's bitfields
* Modify the place and dependancy of the config
* Modify Noop functions
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARMv6 cores do not implement the DBGOSLAR register, so we don't need to
try and clear it on boot. Furthermore, the VCR is zeroed out of reset,
so we don't need to zero it explicitly when a CPU comes online.
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'irq-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
irq: Fix check for already initialized irq_domain in irq_domain_add
irq: Add declaration of irq_domain_simple_ops to irqdomain.h
* 'x86-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
x86/rtc: Don't recursively acquire rtc_lock
* 'sched-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
posix-cpu-timers: Cure SMP wobbles
sched: Fix up wchan borkage
sched/rt: Migrate equal priority tasks to available CPUs
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] cio: fix cio_tpi ignoring adapter interrupts
[S390] gmap: always up mmap_sem properly
[S390] Do not clobber personality flags on exec
* git://github.com/davem330/sparc:
sparc64: Force the execute bit in OpenFirmware's translation entries.
sparc: Make '-p' boot option meaningful again.
sparc, exec: remove redundant addr_limit assignment
sparc64: Future proof Niagara cpu detection.
Apple Quad G5 has some oddity in it's device-tree which causes the new
generic matching code to fail to relate nodes for PCI-E devices below U4
with their respective struct pci_dev. This breaks graphics on those
machines among others.
This fixes it using a quirk which copies the node pointer from the host
bridge for the root complex, which makes the generic code work for the
children afterward.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the OF 'translations' property, the template TTEs in the mappings
never specify the executable bit. This is the case even though some
of these mappings are for OF's code segment.
Therefore, we need to force the execute bit on in every mapping.
This problem can only really trigger on Niagara/sun4v machines and the
history behind this is a little complicated.
Previous to sun4v, the sun4u TTE entries lacked a hardware execute
permission bit. So OF didn't have to ever worry about setting
anything to handle executable pages. Any valid TTE loaded into the
I-TLB would be respected by the chip.
But sun4v Niagara chips have a real hardware enforced executable bit
in their TTEs. So it has to be set or else the I-TLB throws an
instruction access exception with type code 6 (protection violation).
We've been extremely fortunate to not get bitten by this in the past.
The best I can tell is that the OF's mappings for it's executable code
were mapped using permanent locked mappings on sun4v in the past.
Therefore, the fact that we didn't have the exec bit set in the OF
translations we would use did not matter in practice.
Thanks to Greg Onufer for helping me track this down.
Signed-off-by: David S. Miller <davem@davemloft.net>
The sclk_cam clocks are now controlled by the top level FIMC media
device driver bound to "s5p-fimc-md" platform device.
Rename sclk_cam clocks so they accessible by the corresponding
driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The sclk_cam clocks are now controlled by the top level FIMC media
device driver bound to "s5p-fimc-md" platform device.
Rename sclk_cam clocks so they accessible by the corresponding
driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7099/1: futex: preserve oldval in SMP __futex_atomic_op
ARM: dma-mapping: free allocated page if unable to map
ARM: fix vmlinux.lds.S discarding sections
ARM: nommu: fix warning with checksyscalls.sh
ARM: 7091/1: errata: D-cache line maintenance operation by MVA may not succeed
If gmap_unmap_segment figures that the segment was not mapped in the
first place, it need to up mmap_sem on exit.
Cc: <stable@kernel.org>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Analog to git commit 59e4c3a2fe
do not clear the additional personality flags on exec. We
need to inherit the personality bits in PER_MASK across exec.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The SMP implementation of __futex_atomic_op clobbers oldval with the
status flag from the exclusive store. This causes it to always read as
zero when performing the FUTEX_OP_CMP_* operation.
This patch updates the ARM __futex_atomic_op implementations to take a
tmp argument, allowing us to store the strex status flag without
overwriting the register containing oldval.
Cc: stable@kernel.org
Reported-by: Minho Ban <mhban@samsung.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the attempt to map a page for DMA fails (eg, because we're out of
mapping space) then we must not hold on to the page we allocated for
DMA - doing so will result in a memory leak.
Cc: <stable@kernel.org>
Reported-by: Bryan Phillippe <bp@darkforest.org>
Tested-by: Bryan Phillippe <bp@darkforest.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Loop iterator value after terminating list_for_each_entry()
is not NULL. This patch fixes incorrect iterator usage in
GPIO interrupt code for SAMSUNG S5P platforms.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The changed statement should set the old armdiv bits to 0
and not everything else, before setting the new value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Src2CL decode (used for double width shifts) erronously decodes only bit 3
of %rcx, instead of bits 7:0.
Fix by decoding %cl in its entirety.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
__update_clear_spte_slow should return original spte while the
current code returns low half of original spte combined with high
half of new spte.
Signed-off-by: Zhao Jin <cronozhj@gmail.com>
Reviewed-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
On certain architectures, there might be a need to mark certain
addresses with strongly ordered memory attributes to avoid ordering
issues at the interconnect level.
On OMAP4, the asynchronous bridge buffers can only be drained
with strongly ordered accesses and hence the need to mark the
memory strongly ordered.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Woodruff Richard <r-woodruff2@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Function vfp_force_reload() clears vfp_current_hw_state, so
update the comment accordingly.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tegra can benefit from the IRQCHIP_MASK_ON_SUSPEND flag, allow it
to be passed to the gic irq chip.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-and-Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
When the cpu is powered down in a low power mode, the vfp
registers may be reset.
This patch uses CPU_PM_ENTER and CPU_PM_EXIT notifiers to save
and restore the cpu's vfp registers.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-and-Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
When the cpu is powered down in a low power mode, the gic cpu
interface may be reset, and when the cpu cluster is powered
down, the gic distributor may also be reset.
This patch uses CPU_PM_ENTER and CPU_PM_EXIT notifiers to save
and restore the gic cpu interface registers, and the
CPU_CLUSTER_PM_ENTER and CPU_CLUSTER_PM_EXIT notifiers to save
and restore the gic distributor registers.
Original-author: Gary King <gking@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-and-Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] kvm: extension capability for new address space layout
[S390] kvm: fix address mode switching
If "-p" is given on the command line, clear the CON_BOOT
flag for the initial early boot PROM console.
This is necessary to try and see crash messages that occur
between the registry of the VT console and the probing of
the first framebuffer or serial console. During this time
no console messages are emitted because the VT console
registry (even if no backend is registered to it) removes
the early console if CON_BOOT is set.
Signed-off-by: David S. Miller <davem@davemloft.net>
A deadlock was introduced on x86 in commit ef68c8f87e ("x86:
Serialize EFI time accesses on rtc_lock") because efi_get_time()
and friends can be called with rtc_lock already held by
read_persistent_time(), e.g.:
timekeeping_init()
read_persistent_clock() <-- acquire rtc_lock
efi_get_time()
phys_efi_get_time() <-- acquire rtc_lock <DEADLOCK>
To fix this let's push the locking down into the get_wallclock()
and set_wallclock() implementations. Only the clock
implementations that access the x86 RTC directly need to acquire
rtc_lock, so it makes sense to push the locking down into the
rtc, vrtc and efi code.
The virtualization implementations don't require rtc_lock to be
held because they provide their own serialization.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Acked-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Avi Kivity <avi@redhat.com> [for the virtualization aspect]
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The address limit is already set in flush_old_exec() so this assignment of
USER_DS is redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are seeing linker errors caused by sections being discarded, despite
the linker script trying to keep them. The result is (eg):
`.exit.text' referenced in section `.alt.smp.init' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
`.exit.text' referenced in section `.alt.smp.init' of net/built-in.o: defined in discarded section `.exit.text' of net/built-in.o
This is the relevent part of the linker script (reformatted to make it
clearer):
| SECTIONS
| {
| /*
| * unwind exit sections must be discarded before the rest of the
| * unwind sections get included.
| */
| /DISCARD/ : {
| *(.ARM.exidx.exit.text)
| *(.ARM.extab.exit.text)
| }
| ...
| .exit.text : {
| *(.exit.text)
| *(.memexit.text)
| }
| ...
| /DISCARD/ : {
| *(.exit.text)
| *(.memexit.text)
| *(.exit.data)
| *(.memexit.data)
| *(.memexit.rodata)
| *(.exitcall.exit)
| *(.discard)
| *(.discard.*)
| }
| }
Now, this is what the linker manual says about discarded output sections:
| The special output section name `/DISCARD/' may be used to discard
| input sections. Any input sections which are assigned to an output
| section named `/DISCARD/' are not included in the output file.
No questions, no exceptions. It doesn't say "unless they are listed
before the /DISCARD/ section." Now, this is what asn-generic/vmlinux.lds.S
says:
| /*
| * Default discarded sections.
| *
| * Some archs want to discard exit text/data at runtime rather than
| * link time due to cross-section references such as alt instructions,
| * bug table, eh_frame, etc. DISCARDS must be the last of output
| * section definitions so that such archs put those in earlier section
| * definitions.
| */
And guess what - the list _always_ includes .exit.text etc.
Now, what's actually happening is that the linker is reading the script,
and it finds the first /DISCARD/ output section at the beginning of the
script. It continues reading the script, and finds the 'DISCARD' macro
at the end, which having been postprocessed results in another
/DISCARD/ output section. As the linker already contains the earlier
/DISCARD/ output section, it adds it to that existing section, so it
effectively is placed at the start. This can be seen by using the -M
option to ld:
| Linker script and memory map
|
| 0xc037c080 jiffies = jiffies_64
|
| /DISCARD/
| *(.ARM.exidx.exit.text)
| *(.ARM.extab.exit.text)
| *(.exit.text)
| *(.memexit.text)
| *(.exit.data)
| *(.memexit.data)
| *(.memexit.rodata)
| *(.exitcall.exit)
| *(.discard)
| *(.discard.*)
|
| 0xc0008000 . = 0xc0008000
|
| .head.text 0xc0008000 0x1d0
| 0xc0008000 _text = .
| *(.head.text)
| .head.text 0xc0008000 0x1d0 arch/arm/kernel/head.o
| 0xc0008000 stext
|
| .text 0xc0008200 0x2d78d0
| 0xc0008200 _stext = .
| 0xc0008200 __exception_text_start = .
| *(.exception.text)
| .exception.text
| ...
As you can see, all the discarded sections are grouped together - and
as a result of it being the first output section, they all appear before
any other section.
The result is that not only is the unwind information discarded (as
intended), but also the .exit.text, despite us wanting to have the
.exit.text preserved.
We can't move the unwind information elsewhere, because it'll then be
included even when we do actually discard the .exit.text (and similar)
sections.
So, work around this by avoiding the generic DISCARDS macro, and instead
conditionalize the sections to be discarded ourselves. This avoids the
ambiguity in how the linker assigns input sections to output sections,
making our script less dependent on undocumented linker behaviour.
Reported-by: Rob Herring <robherring2@gmail.com>
Tested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to ensure that state is pushed out from the L2 cache when
suspending so that the resume paths can access their data before the
MMU and caches have been re-initialized. Add the necessary calls to
__cpu_suspend_save().
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert some of the sleep.S guts to C code, which makes it easier to
use our macros and to add L2 cache handling. We provide a helper
function, __cpu_suspend_save(), which deals with saving the common
state, setting up for resume, and flushing caches.
The remainder left as assembly code is the saving of the CPU general
purpose registers, and allocating space on the stack to save the CPU
specific registers and resume state.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
