- Add __counted_by to struct clk_hw_onecell_data and struct spmi_pmic_div_clk_cc
- Remove non-OF mmp clk drivers
- Move number of clks from DT headers to drivers
* clk-imx:
clk: imx: pll14xx: dynamically configure PLL for 393216000/361267200Hz
clk: imx: pll14xx: align pdiv with reference manual
clk: imx: composite-8m: fix clock pauses when set_rate would be a no-op
clk: imx25: make __mx25_clocks_init return void
clk: imx25: print silicon revision during init
dt-bindings: clocks: imx8mp: make sai4 a dummy clock
clk: imx8mp: fix sai4 clock
clk: imx: imx8ulp: update SPLL2 type
clk: imx: pllv4: Fix SPLL2 MULT range
clk: imx: imx8: add audio clock mux driver
dt-bindings: clock: fsl,imx8-acm: Add audio clock mux support
clk: imx: clk-imx8qxp-lpcg: Convert to devm_platform_ioremap_resource()
clk: imx: clk-gpr-mux: Simplify .determine_rate()
clk: imx: Add 519.75MHz frequency support for imx9 pll
clk: imx93: Add PDM IPG clk
dt-bindings: clock: imx93: Add PDM IPG clk
* clk-samsung:
dt-bindings: clock: samsung: remove define with number of clocks
clk: samsung: exynoautov9: do not define number of clocks in bindings
clk: samsung: exynos850: do not define number of clocks in bindings
clk: samsung: exynos7885: do not define number of clocks in bindings
clk: samsung: exynos5433: do not define number of clocks in bindings
clk: samsung: exynos5420: do not define number of clocks in bindings
clk: samsung: exynos5410: do not define number of clocks in bindings
clk: samsung: exynos5260: do not define number of clocks in bindings
clk: samsung: exynos5250: do not define number of clocks in bindings
clk: samsung: exynos4: do not define number of clocks in bindings
clk: samsung: exynos3250: do not define number of clocks in bindings
* clk-annotate:
clk: qcom: clk-spmi-pmic-div: Annotate struct spmi_pmic_div_clk_cc with __counted_by
clk: Annotate struct clk_hw_onecell_data with __counted_by
* clk-marvell:
clk: pxa910: Move number of clocks to driver source
clk: pxa1928: Move number of clocks to driver source
clk: pxa168: Move number of clocks to driver source
clk: mmp2: Move number of clocks to driver source
clk: mmp: Remove old non-OF clock drivers
* clk-lmk:
clk: lmk04832: Support using PLL1_LD as SPI readback pin
clk: lmk04832: Don't disable vco clock on probe fail
clk: lmk04832: Set missing parent_names for output clocks
- Add Versa3 clk generator to support 48KHz playback/record with audio
codec on RZ/G2L SMARC EVK
- Introduce kstrdup_and_replace() and use it
* clk-versa:
clk: vc7: Use i2c_get_match_data() instead of device_get_match_data()
clk: vc5: Use i2c_get_match_data() instead of device_get_match_data()
clk: versaclock3: Switch to use i2c_driver's probe callback
clk: Add support for versa3 clock driver
dt-bindings: clock: Add Renesas versa3 clock generator bindings
* clk-strdup:
clk: ti: Replace kstrdup() + strreplace() with kstrdup_and_replace()
clk: tegra: Replace kstrdup() + strreplace() with kstrdup_and_replace()
driver core: Replace kstrdup() + strreplace() with kstrdup_and_replace()
lib/string_helpers: Add kstrdup_and_replace() helper
* clk-amlogic: (22 commits)
dt-bindings: soc: amlogic: document System Control registers
dt-bindings: clock: amlogic: convert amlogic,gxbb-aoclkc.txt to dt-schema
dt-bindings: clock: amlogic: convert amlogic,gxbb-clkc.txt to dt-schema
clk: meson: axg-audio: move bindings include to main driver
clk: meson: meson8b: move bindings include to main driver
clk: meson: a1: move bindings include to main driver
clk: meson: eeclk: move bindings include to main driver
clk: meson: aoclk: move bindings include to main driver
dt-bindings: clk: axg-audio-clkc: expose all clock ids
dt-bindings: clk: amlogic,a1-pll-clkc: expose all clock ids
dt-bindings: clk: amlogic,a1-peripherals-clkc: expose all clock ids
dt-bindings: clk: meson8b-clkc: expose all clock ids
dt-bindings: clk: g12a-aoclkc: expose all clock ids
dt-bindings: clk: g12a-clks: expose all clock ids
dt-bindings: clk: axg-clkc: expose all clock ids
dt-bindings: clk: gxbb-clkc: expose all clock ids
clk: meson: migrate axg-audio out of hw_onecell_data to drop NR_CLKS
clk: meson: migrate meson8b out of hw_onecell_data to drop NR_CLKS
clk: meson: migrate a1 clock drivers out of hw_onecell_data to drop NR_CLKS
clk: meson: migrate meson-aoclk out of hw_onecell_data to drop NR_CLKS
...
* clk-allwinner:
clk: sunxi-ng: nkm: Prefer current parent rate
clk: sunxi-ng: a64: select closest rate for pll-video0
clk: sunxi-ng: div: Support finding closest rate
clk: sunxi-ng: mux: Support finding closest rate
clk: sunxi-ng: nkm: Support finding closest rate
clk: sunxi-ng: nm: Support finding closest rate
clk: sunxi-ng: Add helper function to find closest rate
clk: sunxi-ng: Add feature to find closest rate
clk: sunxi-ng: a64: allow pll-mipi to set parent's rate
clk: sunxi-ng: nkm: consider alternative parent rates when determining rate
clk: sunxi-ng: nkm: Use correct parameter name for parent HW
clk: sunxi-ng: Modify mismatched function name
clk: sunxi: sun9i-mmc: Use devm_platform_get_and_ioremap_resource()
* clk-rockchip:
clk: rockchip: rv1126: Add PD_VO clock tree
clk: rockchip: rk3568: Fix PLL rate setting for 78.75MHz
clk: rockchip: rk3568: Add PLL rate for 101MHz
Add the clock dt-binding file for Audio Clock Mux. which
is the IP for i.MX8QM, i.MX8QXP, i.MX8DXL.
Add the clockid for clocks in header file.
The Audio Clock Mux is binded with all the audio IP and audio clocks
in the subsystem, so need to list the power domain of related clocks
and IPs. Each clock and IP has a power domain, so there are so many
power domains.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/1690260984-25744-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Add support for GCC_GPLL1_OUT_EVEN and GCC_DDRSS_ECPRI_GSI_CLK clock
bindings for QDU1000 and QRU1000 SoCs. While at it, update the
maintainers list.
Signed-off-by: Imran Shaik <quic_imrashai@quicinc.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230803105741.2292309-2-quic_imrashai@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
We've not been consuming that clock for no apparent reason. Describe it.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230622-topic-8998clk-v2-2-6222fbc2916b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This patch adds support for the global clock controller found on
the IPQ5018 based devices.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Co-developed-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Link: https://lore.kernel.org/r/1690533192-22220-2-git-send-email-quic_srichara@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
select:false makes the schema basically ignored and not effective, which
is clearly not what we want for a device binding.
Fixes: 352546805a ("dt-bindings: clock: Add bindings for versal clock driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230728165923.108589-1-krzysztof.kozlowski@linaro.org
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The CBF clock on MSM8996 Pro has a different divisor compared to MSM8996
and is therefore not fully compatible with it. Add a new compatible string
to differentiate between them.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230527093934.101335-2-y.oudjana@protonmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The global clock controller on MDM9615 uses external CXO and PLL7
clocks. Split the qcom,gcc-mdm9615 to the separate schema file.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230512211727.3445575-4-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Describe parent clocks used by the LCC on the MDM9615 platform. It is
the list as the one for msm8960/apq8064, with only difference being
pxo/cxo replacement.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230512211727.3445575-2-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
SC8280XP reuses the SM8350 video clock controller block, changing just a
couple tunables. Docuemnt it.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230703-topic-8280_videocc-v2-1-c88269806269@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Document Renesas versa3 clock generator(5P35023) bindings.
The 5P35023 is a VersaClock programmable clock generator and
is designed for low-power, consumer, and high-performance PCI
Express applications. The 5P35023 device is a three PLL
architecture design, and each PLL is individually programmable
and allowing for up to 6 unique frequency outputs.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230705171000.85786-2-biju.das.jz@bp.renesas.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Due to lack of maintenance and stall of development for a few years now,
and since no new features will ever be added upstream, remove the
OX810 and OX820 clock bindings.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230630-topic-oxnas-upstream-remove-v2-2-fb6ab3dea87c@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add dt-binding documentation for Versal NET platforms.
Versal Net is a new AMD/Xilinx SoC.
The SoC and its architecture is based on the Versal ACAP device.
The Versal Net device includes more security features in the
platform management controller (PMC) and increases the number of
CPUs in the application processing unit (APU) and the real-time
processing unit (RPU).
Signed-off-by: Jay Buddhabhatti <jay.buddhabhatti@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Link: https://lore.kernel.org/r/20230620110137.5701-1-shubhrajyoti.datta@amd.com
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The "hisilicon,hix5hd2-clock" is simple enough to just add it into its
parent node binding, "hisilicon,cpuctrl".
This fixes a warning that "hisilicon,hix5hd2-clock" is missing a schema.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230707210700.869060-1-robh@kernel.org
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add bindings for the Video-Output clock and reset generator (VOUTCRG)
on the JH7110 RISC-V SoC by StarFive Ltd.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add bindings for the Image-Signal-Process clock and reset
generator (ISPCRG) on the JH7110 RISC-V SoC by StarFive Ltd.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add bindings for the System-Top-Group clock and reset generator (STGCRG)
on the JH7110 RISC-V SoC by StarFive Ltd.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Update my email address from the defunct codeaurora.org domain to the
current quicinc.com domain.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20230627173123.9221-1-quic_tdas@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
driver updates needed more time to bake in linux-next.
Updates:
- Support for more clk controllers in Qualcomm SoCs such as SM8350,
SM8450, SDX75, SC8280XP, and IPQ9574
- Runtime PM enablement of some more Qualcomm clk controllers
- Various fixes to Qualcomm clk driver data to use correct clk_ops
and to check halt bits properly
- AT91 updates to modernize with clk_parent_data structures
Fixes:
- Remove "syscon" from dt binding fix for ti,j721e-system-controller
- Fix determine rate in the Tegra driver that got wrecked by the
refactorting of muxes this merge window
-----BEGIN PGP SIGNATURE-----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=cF5c
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull more clk updates from Stephen Boyd:
"Another set of clk driver updates and fixes for the merge window. The
driver updates needed more time to bake in linux-next.
Updates:
- Support for more clk controllers in Qualcomm SoCs such as SM8350,
SM8450, SDX75, SC8280XP, and IPQ9574
- Runtime PM enablement of some more Qualcomm clk controllers
- Various fixes to Qualcomm clk driver data to use correct clk_ops
and to check halt bits properly
- AT91 updates to modernize with clk_parent_data structures
Fixes:
- Remove 'syscon' from dt binding fix for ti,j721e-system-controller
- Fix determine rate in the Tegra driver that got wrecked by the
refactorting of muxes this merge window"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (69 commits)
clk: tegra: Avoid calling an uninitialized function
dt-bindings: mfd: ti,j721e-system-controller: Remove syscon from example
clk: at91: sama7g5: s/ep_chg_chg_id/ep_chg_id
clk: at91: sama7g5: switch to parent_hw and parent_data
clk: at91: sckc: switch to parent_data/parent_hw
clk: at91: clk-sam9x60-pll: add support for parent_hw
clk: at91: clk-utmi: add support for parent_hw
clk: at91: clk-system: add support for parent_hw
clk: at91: clk-programmable: add support for parent_hw
clk: at91: clk-peripheral: add support for parent_hw
clk: at91: clk-master: add support for parent_hw
clk: at91: clk-generated: add support for parent_hw
clk: at91: clk-main: add support for parent_data/parent_hw
clk: qcom: gcc-sc8280xp: Add runtime PM
clk: qcom: gpucc-sc8280xp: Add runtime PM
clk: qcom: mmcc-msm8974: fix MDSS_GDSC power flags
clk: qcom: gpucc-sm6375: Enable runtime pm
dt-bindings: clock: sm6375-gpucc: Add VDD_GX
clk: qcom: gcc-sm6115: Add missing PLL config properties
clk: qcom: clk-alpha-pll: Add a way to update some bits of test_ctl(_hi)
...
There are two new SoC families this time, and both appear fairly similar:
The Nuvoton MA35D1 and the STMicroelectronics STM32MP2 are both dual-core
Cortex-A35 based chips for the low-power industrial embedded market,
and they mark the first 64-bit product in a widely used family of 32-bit
Arm MCUs and SoCs.
The way into the kernel is completely different here: The team at ST has
a long history of working upstream with their STM32MP1 and other SoCs,
and they produced a complete port to arm64 together with the initial
announcement. Nuvoton also has multiple SoC product lines with current
or previous upstream support, but those are maintained by third parties
and are unrelated. The patch series from Nuvoton's Jacky Huang had to
go through many revisisions to get to this point and is still missing
a few drivers including the serial port for the moment.
The branch contains the devicetree files as well as all the code changes,
in order to have something that can be tested standalone.
-----BEGIN PGP SIGNATURE-----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=zaVi
-----END PGP SIGNATURE-----
Merge tag 'soc-newsoc-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull new ARM SoC support from Arnd Bergmann:
"There are two new SoC families this time, and both appear fairly
similar: The Nuvoton MA35D1 and the STMicroelectronics STM32MP2 are
both dual-core Cortex-A35 based chips for the low-power industrial
embedded market, and they mark the first 64-bit product in a widely
used family of 32-bit Arm MCUs and SoCs.
The way into the kernel is completely different here: The team at ST
has a long history of working upstream with their STM32MP1 and other
SoCs, and they produced a complete port to arm64 together with the
initial announcement. Nuvoton also has multiple SoC product lines with
current or previous upstream support, but those are maintained by
third parties and are unrelated. The patch series from Nuvoton's Jacky
Huang had to go through many revisisions to get to this point and is
still missing a few drivers including the serial port for the moment.
The branch contains the devicetree files as well as all the code
changes, in order to have something that can be tested standalone"
* tag 'soc-newsoc-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
clk: nuvoton: Use clk_parent_data instead of string for parent clock
clk: nuvoton: Update all constant hex values to lowercase
clk: nuvoton: Add clk-ma35d1.h for driver extern functions
remoteproc: stm32: use correct format strings on 64-bit
MAINTAINERS: add entry for ARM/STM32 ARCHITECTURE
arm64: defconfig: enable ARCH_STM32 and STM32 serial driver
arm64: dts: st: add stm32mp257f-ev1 board support
dt-bindings: stm32: document stm32mp257f-ev1 board
arm64: dts: st: introduce stm32mp25 pinctrl files
arm64: dts: st: introduce stm32mp25 SoCs family
arm64: introduce STM32 family on Armv8 architecture
dt-bindings: stm32: add st,stm32mp25-syscfg compatible for syscon
pinctrl: stm32: add stm32mp257 pinctrl support
dt-bindings: pinctrl: stm32: support for stm32mp257 and additional packages
Documentation/process: add soc maintainer handbook
reset: RESET_NUVOTON_MA35D1 should depend on ARCH_MA35
reset: Add Nuvoton ma35d1 reset driver support
clk: nuvoton: Add clock driver for ma35d1 clock controller
arm64: dts: nuvoton: Add initial ma35d1 device tree
dt-bindings: serial: Document ma35d1 uart controller
...
The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for each
SoC vendor, following the same scheme that is used on arm64, mips and
riscv. This has been discussed for many years, but so far we never did
this as there was a plan to move the files out of the kernel entirely,
which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along
with their device drivers.
* The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the time.
* Amlogic C3 is a Cortex-A35 based smart IP camera chip
* Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
* Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
* Qualcomm SDX75 is the latest generation modem chip that is used
as a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
* Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the Xuantie
C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those included
there are 39 new board files, but only five more 32-bit this time, probably
a new low:
* Marantec Maveo board based on dhcor imx6ull module
* Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
* Epson Moverio BT-200 AR glasses based on TI OMAP4
* PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
* ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than
we had in the recent releases:
* Three boards based on NXP i.MX8: Emtop SoM & Baseboard,
NXP i.MX8MM EVKB board and i.MX8MP based Gateworks Venice
gw7905-2x device.
* NVIDIA IGX Orin and Jetson Orin Nano boards, both based on
tegra234
* Qualcomm gains support for 6 reference boards on various members
of their IPQ networking SoC series, as well as the Sony Xperia M4
Aqua phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board
on top of the various reference platforms for their new chips.
* Rockchips support for several newer boards: Indiedroid Nova (rk3588),
Edgeble Neural Compute Module 6B (rk3588), FriendlyARM NanoPi R2C
Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn Fastrhino R66S/R68S
(rk3568)
* TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex Verdin
family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
* continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
* support for devicetree overlays on at91, bcm283x
* significant additions to existing SoC support on mediatek, qualcomm,
ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST STM32MP1
As usual, a lot more detail is available in the individual merge
commits.
-----BEGIN PGP SIGNATURE-----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=X/KE
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for
each SoC vendor, following the same scheme that is used on arm64, mips
and riscv. This has been discussed for many years, but so far we never
did this as there was a plan to move the files out of the kernel
entirely, which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along with
their device drivers.
- The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the
time.
- Amlogic C3 is a Cortex-A35 based smart IP camera chip
- Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
- Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
- Qualcomm SDX75 is the latest generation modem chip that is used as
a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
- Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
Xuantie C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those
included there are 39 new board files, but only five more 32-bit this
time, probably a new low:
- Marantec Maveo board based on dhcor imx6ull module
- Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
- Epson Moverio BT-200 AR glasses based on TI OMAP4
- PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
- ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than we had
in the recent releases:
- Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.
- NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234
- Qualcomm gains support for 6 reference boards on various members of
their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
of the various reference platforms for their new chips.
- Rockchips support for several newer boards: Indiedroid Nova
(rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
Fastrhino R66S/R68S (rk3568)
- TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
Verdin family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
- continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
- support for devicetree overlays on at91, bcm283x
- significant additions to existing SoC support on mediatek,
qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
STM32MP1
As usual, a lot more detail is available in the individual merge
commits"
* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
ARM: mvebu: fix unit address on armada-390-db flash
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
arm: dts: Enable device-tree overlay support for AT91 boards
arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
ARM: dts: at91: use generic name for shutdown controller
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
...
- added support for Wifi/Bluetooth on CI20
- reworked Ralink clock and reset handling
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=z9/q
-----END PGP SIGNATURE-----
Merge tag 'mips_6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- add support for TP-Link HC220 G5 v1
- add support for Wifi/Bluetooth on CI20
- rework Ralink clock and reset handling
- cleanups and fixes
* tag 'mips_6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (58 commits)
MIPS: Loongson64: DTS: Add RTC support to Loongson-2K1000
MIPS: Loongson64: DTS: Add RTC support to LS7A PCH
MIPS: OCTEON: octeon-usb: cleanup divider calculation
MIPS: OCTEON: octeon-usb: introduce dwc3_octeon_{read,write}q
MIPS: OCTEON: octeon-usb: move gpio config to separate function
MIPS: OCTEON: octeon-usb: use bitfields for shim register
MIPS: OCTEON: octeon-usb: use bitfields for host config register
MIPS: OCTEON: octeon-usb: use bitfields for control register
MIPS: OCTEON: octeon-usb: add all register offsets
mips: ralink: match all supported system controller compatible strings
MIPS: dec: prom: Address -Warray-bounds warning
MIPS: DTS: CI20: Raise VDDCORE voltage to 1.125 volts
clk: ralink: mtmips: Fix uninitialized use of ret in mtmips_register_{fixed,factor}_clocks()
mips: ralink: introduce commonly used remap node function
mips: pci-mt7620: use dev_info() to log PCIe device detection result
mips: pci-mt7620: do not print NFTS register value as error log
MAINTAINERS: add Mediatek MTMIPS Clock maintainer
mips: ralink: get cpu rate from new driver code
mips: ralink: remove reset related code
mips: ralink: mt7620: remove clock related code
...
Bindings:
- Add some missing type definitions to properties
- Drop unneeded quotes and use absolute paths in bindings
- Remove redundant "binding" or "schema" in binding titles
- Add bindings for Ralink SoCs interrupt controller, QCA2066 Bluetooth,
infineon,irps5401, new NXP i.MX GPT variants, shineworld lh133k MIPI
SPI panel, Socionext Synquacer platforms, RK3588 PCIe, ST M95640
EEPROM, and FSL DCP crypto variants, and Arm Cortex-R52
DT core:
- Improve the reserved-memory range allocation to maximize contiguous
space
- Use device_set_node() helper in place of open coding
-----BEGIN PGP SIGNATURE-----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=onek
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"Bindings:
- Add some missing type definitions to properties
- Drop unneeded quotes and use absolute paths in bindings
- Remove redundant "binding" or "schema" in binding titles
- Add bindings for Ralink SoCs interrupt controller, QCA2066
Bluetooth, infineon,irps5401, new NXP i.MX GPT variants, shineworld
lh133k MIPI SPI panel, Socionext Synquacer platforms, RK3588 PCIe,
ST M95640 EEPROM, and FSL DCP crypto variants, and Arm Cortex-R52
DT core:
- Improve the reserved-memory range allocation to maximize contiguous
space
- Use device_set_node() helper in place of open coding"
* tag 'devicetree-for-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (40 commits)
dt-bindings: interrupt-controller: add Ralink SoCs interrupt controller
dt-bindings: PCI: dwc: rockchip: Update for RK3588
dt-bindings: auxdisplay: holtek: Add missing type for "linux,no-autorepeat"
dt-bindings: input: mediatek,pmic-keys: Fix typo in "linux,keycodes" property name
dt-bindings: pwm: drop unneeded quotes
dt-bindings: crypto: drop unneeded quotes
dt-bindings: arm: socionext: add Synquacer platforms
dt-bindings: connector: usb: allow a single HS port
dt-bindings: bus: ti-sysc: fix typo
of: reserved_mem: Use stable allocation order
of: reserved_mem: Try to keep range allocations contiguous
dt-bindings: arm: drop unneeded quotes and use absolute /schemas path
dt-bindings: firmware: arm,scmi: drop unneeded quotes and use absolute /schemas path
dt-bindings: dvfs: drop unneeded quotes
dt-bindings: gpu: drop unneeded quotes
dt-bindings: i3c: silvaco,i3c-master: drop unneeded quotes
dt-bindings: rockchip: grf: drop unneeded quotes
dt-bindings: spmi: mtk,spmi-mtk-pmif: drop unneeded quotes
dt-bindings: Remove last usage of "binding" or "schema" in titles
dt-bindings: display: panel: mipi-dbi-spi: add spi-3wire property
...
SoC support. Instead there's a treewide patch series from Maxime that makes
clk_ops::determine_rate mandatory for muxes. Beyond that core framework change
we have the usual pile of clk driver updates such as migrating i2c drivers to
use .probe() again or YAMLfication of clk DT bindings so we can validate DTBs.
Overall the SoCs that got the most updates this time around in terms of
diffstat are the Amlogic and Mediatek drivers because they added new SoC
support or fixed up various drivers to have proper data.
In general things look kinda quiet. I suspect the core framework change may
still shake out some problems after the merge window, mostly because not
everyone tests linux-next where that series has been for some number of weeks.
I saw that there's at least one pending fix for Tegra that needs to be wrapped
up into a proper patch. I'll try to catch those bits before the window closes
so that -rc1 is bootable. More details below.
Core:
- Make clk_ops::determine_rate mandatory for muxes
New Drivers:
- Add amlogic a1 SoC family PLL and peripheral clock controller support
Updates:
- Handle allocation failures from kasprintf() and friends
- Migrate platform clk drivers to .remove_new()
- Migrate i2c clk drivers to .probe() instead of .probe_new()
- Remove CLK_SET_PARENT from all Mediatek MSDC core clocks
- Add infra_ao reset support for Mediatek MT8188 SoCs
- Align driver_data to i2c_device_id tables in some i2c clk drivers
- Use device_get_match_data() in vc5 clk driver
- New Kconfig symbol name (SOC_MICROCHIP_POLARFIRE) for Microchip FPGA clock
drivers
- Use of_property_read_bool() to read "microchip,pic32mzda-sosc" boolean DT
property in clk-pic32mzda
- Convert AT91 clock dt-bindings to YAML
- Remove CLK_SET_RATE_PARENT flag from LDB clocks on i.MX6SX
- Keep i.MX UART clocks enabled during kernel boot if earlycon is set
- Drop imx_unregister_clocks() as there are no users anymore
- Switch to _safe iterator on imx_clk_scu_unregister() to avoid use after free
- Add determine_rate op to the imx8m composite clock
- Use device managed API for iomap and kzalloc for i.MXRT1050, i.MX8MN,
i.MX8MP and i.MX93 clock controller drivers
- Add missing interrupt DT property for the i.MX8M clock controller
- Re-add support for Exynos4212 clock controller because we are
re-introducing the SoC in the mainline
- Add CONFIG_OF dependency to Samsung clk Kconfig symbols to solve some
objtool warnings
- Preselect PLL MIPI as TCON0 parent for Allwinner A64 SoC
- Convert the Renesas clock drivers to readl_poll_timeout_atomic()
- Add PWM clock on Renesas R-Car V3U
- Fix PLL5 on Renesas RZ/G2L and RZ/V2L
-----BEGIN PGP SIGNATURE-----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=6M8D
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This batch of clk driver updates contains almost no new SoC support.
Instead there's a treewide patch series from Maxime that makes
clk_ops::determine_rate mandatory for muxes.
Beyond that core framework change we have the usual pile of clk driver
updates such as migrating i2c drivers to use .probe() again or
YAMLfication of clk DT bindings so we can validate DTBs.
Overall the SoCs that got the most updates this time around in terms
of diffstat are the Amlogic and Mediatek drivers because they added
new SoC support or fixed up various drivers to have proper data.
In general things look kinda quiet. I suspect the core framework
change may still shake out some problems after the merge window,
mostly because not everyone tests linux-next where that series has
been for some number of weeks. I saw that there's at least one pending
fix for Tegra that needs to be wrapped up into a proper patch. I'll
try to catch those bits before the window closes so that -rc1 is
bootable. More details below.
Core:
- Make clk_ops::determine_rate mandatory for muxes
New Drivers:
- Add amlogic a1 SoC family PLL and peripheral clock controller support
Updates:
- Handle allocation failures from kasprintf() and friends
- Migrate platform clk drivers to .remove_new()
- Migrate i2c clk drivers to .probe() instead of .probe_new()
- Remove CLK_SET_PARENT from all Mediatek MSDC core clocks
- Add infra_ao reset support for Mediatek MT8188 SoCs
- Align driver_data to i2c_device_id tables in some i2c clk drivers
- Use device_get_match_data() in vc5 clk driver
- New Kconfig symbol name (SOC_MICROCHIP_POLARFIRE) for Microchip
FPGA clock drivers
- Use of_property_read_bool() to read "microchip,pic32mzda-sosc"
boolean DT property in clk-pic32mzda
- Convert AT91 clock dt-bindings to YAML
- Remove CLK_SET_RATE_PARENT flag from LDB clocks on i.MX6SX
- Keep i.MX UART clocks enabled during kernel boot if earlycon is set
- Drop imx_unregister_clocks() as there are no users anymore
- Switch to _safe iterator on imx_clk_scu_unregister() to avoid use
after free
- Add determine_rate op to the imx8m composite clock
- Use device managed API for iomap and kzalloc for i.MXRT1050,
i.MX8MN, i.MX8MP and i.MX93 clock controller drivers
- Add missing interrupt DT property for the i.MX8M clock controller
- Re-add support for Exynos4212 clock controller because we are
re-introducing the SoC in the mainline
- Add CONFIG_OF dependency to Samsung clk Kconfig symbols to solve
some objtool warnings
- Preselect PLL MIPI as TCON0 parent for Allwinner A64 SoC
- Convert the Renesas clock drivers to readl_poll_timeout_atomic()
- Add PWM clock on Renesas R-Car V3U
- Fix PLL5 on Renesas RZ/G2L and RZ/V2L"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (149 commits)
clk: fix typo in clk_hw_register_fixed_rate_parent_data() macro
clk: Fix memory leak in devm_clk_notifier_register()
clk: mvebu: Iterate over possible CPUs instead of DT CPU nodes
clk: mvebu: Use of_get_cpu_hwid() to read CPU ID
MAINTAINERS: Add Marvell mvebu clock drivers
clk: clocking-wizard: check return value of devm_kasprintf()
clk: ti: clkctrl: check return value of kasprintf()
clk: keystone: sci-clk: check return value of kasprintf()
clk: si5341: free unused memory on probe failure
clk: si5341: check return value of {devm_}kasprintf()
clk: si5341: return error if one synth clock registration fails
clk: cdce925: check return value of kasprintf()
clk: vc5: check memory returned by kasprintf()
clk: mediatek: clk-mt8173-apmixedsys: Fix iomap not released issue
clk: mediatek: clk-mt8173-apmixedsys: Fix return value for of_iomap() error
clk: mediatek: clk-mtk: Grab iomem pointer for divider clocks
clk: keystone: syscon-clk: Add support for audio refclk
dt-bindings: clock: Add binding documentation for TI Audio REFCLK
dt-bindings: clock: ehrpwm: Remove unneeded syscon compatible
clk: keystone: syscon-clk: Allow the clock node to not be of type syscon
...
Merge the missing SC8280XP LPASS DeviceTree changes, which where brought
in through a topic branch in order to be shared with the DeviceTree
source files, but not merged into the clock tree until now.
- Handle allocation failures from kasprintf() and friends
* clk-imx:
clk: imx: clk-imx8mp: improve error handling in imx8mp_clocks_probe()
clk: imx93: fix memory leak and missing unwind goto in imx93_clocks_probe
clk: imx: clk-imx8mn: fix memory leak in imx8mn_clocks_probe
dt-bindings: clock: imx8m: Add missing interrupt property
clk: imx: clk-imxrt1050: fix memory leak in imxrt1050_clocks_probe
clk: imx: composite-8m: Add imx8m_divider_determine_rate
clk: imx: scu: use _safe list iterator to avoid a use after free
clk: imx: drop imx_unregister_clocks
clk: imx6ul: retain early UART clocks during kernel init
clk: imx: imx6sx: Remove CLK_SET_RATE_PARENT from the LDB clocks
* clk-microchip:
dt-bindings: clocks: at91sam9x5-sckc: convert to yaml
dt-bindings: clocks: atmel,at91rm9200-pmc: convert to yaml
clk: microchip: Use of_property_read_bool() for boolean properties
clk: microchip: convert SOC_MICROCHIP_POLARFIRE to ARCH_MICROCHIP_POLARFIRE
* clk-cleanup:
clk: fix typo in clk_hw_register_fixed_rate_parent_data() macro
clk: Fix memory leak in devm_clk_notifier_register()
clk: mvebu: Iterate over possible CPUs instead of DT CPU nodes
clk: mvebu: Use of_get_cpu_hwid() to read CPU ID
MAINTAINERS: Add Marvell mvebu clock drivers
clk: mvebu: Use of_address_to_resource()
clk: tegra: tegra124-emc: Fix potential memory leak
clk: clocking-wizard: Fix Oops in clk_wzrd_register_divider()
clk: bcm: rpi: Fix off by one in raspberrypi_discover_clocks()
clk: sifive: Use devm_platform_ioremap_resource()
* clk-bindings:
dt-bindings: clock: drop unneeded quotes and use absolute /schemas path
dt-bindings: rcc: stm32: Sync with u-boot copy for STM32MP13 SoC
* clk-ti:
clk: keystone: syscon-clk: Add support for audio refclk
dt-bindings: clock: Add binding documentation for TI Audio REFCLK
dt-bindings: clock: ehrpwm: Remove unneeded syscon compatible
clk: keystone: syscon-clk: Allow the clock node to not be of type syscon
* clk-kasprintf:
clk: clocking-wizard: check return value of devm_kasprintf()
clk: ti: clkctrl: check return value of kasprintf()
clk: keystone: sci-clk: check return value of kasprintf()
clk: si5341: free unused memory on probe failure
clk: si5341: check return value of {devm_}kasprintf()
clk: si5341: return error if one synth clock registration fails
clk: cdce925: check return value of kasprintf()
clk: vc5: check memory returned by kasprintf()
Adds device tree binding documentation for system controller node present
in Mediatek MIPS and Ralink SOCs. This node is a clock and reset provider
for the rest of the world. This covers RT2880, RT3050, RT3052, RT3350,
RT3883, RT5350, MT7620, MT7628 and MT7688 SoCs.
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This introduces support for the Qualcomm SDX75 platform, with the IDP
reference board. On IPQ5332 the RDP474 board is added and on IPQ9574 the
RDP454 is introduced.
On SC8280XP, and hence Lenovo ThinkPad X13s, GPU support is added.
For QDU1000, SDM845, SM670, SC8180X, SM6350 and SM8550 the RSC is added
to the CPU cluster power-domain to flush sleep & wake votes as the
cluster goes down.
On IPQ5332 additional reserved-memory regions to improve post mortem
debugging. UART1 is added. The MI01.2 board is renamed RDP441 and the
RDP474 is added.
On IPQ8074 critical thermal trip points are defined.
As with IPQ5332 additional reserved-memory regions are used to improve
post mortem debugging. Thermal sensors (tsens) are added and zones
defined. The crypto engine is added, and support for the RDP454 board is
added.
Across MSM8916 and MSM8939 pinctrl state definitions are cleaned up and
the purpose of msm8939-pm8916 is documented. MSM8939 has regulator
definitions cleaned up, following to the previous effort on MSM8916.
CPU Bus Fabric scaling support is added to MSM8996 Pro.
On QCM2290 CPU idle states are added.
For QDU1000 SDHCI is introduced and enabled on the IDP to gain eMMC
support. IMEM and PIL information regions are defined for improved post
mortem debugging.
The Qualcomm Robotics RB2 kit gets its on-board buttons described.
A few fixes are introduced for the newly merged SC8180X, in particluar
the DisplayPort blocks are moved to the MMCX power domain to avoid power
being reduced prematurely during boot.
The SC8280XP GPU is added and enabled for the Lenovo Thinkpad X13s,
and resets for the soundwire controllers are added. The OUI is
specified for ethernet phys on SA8540P Ride platform, to avoid reset
issues.
Charger description is added to the PMI8998 PMIC and enabled across
OnePlus 6/6T, SHIFT SHIFT6mq and Xiaomi Pocophone F1.
On SM6350 CPU idle states and UART1 are added. And SM6375 gains GPU
clock controller and IOMMU definitions.
The Fairphone FP4 gains Bluetooth support.
SM8150 is transitioned to use 2 interconnect-cells, and the USB
interconnect path is described to ensure buses are adequately voted for.
The same changes are done for SM8250, and the resolution of the
static framebuffer on Sony Xperia 1 II and 5 II are corrected.
The USB bus paths are also added to SM8350, SM8450 and SM8550.
On SM8550 DisplayPort nodes are added, as is the PWM controller for
driving the notification LED and the RTC is enabled. For the MTP and QRD
boards, the soundcard and audio codecs are defined.
A Tegra change, related to LP855X binding changes, was accidentally
picked up and dropped again later.
A number of DeviceTree fixes identified through validation was
introduced as well. Additionally a few nodes got their default status
changed to avoid unnecessarily having to enable them (e.g. the mdp/dpu
node).
-----BEGIN PGP SIGNATURE-----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=Fga/
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=ThxV
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-6.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
More Qualcomm ARM64 DTS changes for v6.5
This introduces support for the Qualcomm SDX75 platform, with the IDP
reference board. On IPQ5332 the RDP474 board is added and on IPQ9574 the
RDP454 is introduced.
On SC8280XP, and hence Lenovo ThinkPad X13s, GPU support is added.
For QDU1000, SDM845, SM670, SC8180X, SM6350 and SM8550 the RSC is added
to the CPU cluster power-domain to flush sleep & wake votes as the
cluster goes down.
On IPQ5332 additional reserved-memory regions to improve post mortem
debugging. UART1 is added. The MI01.2 board is renamed RDP441 and the
RDP474 is added.
On IPQ8074 critical thermal trip points are defined.
As with IPQ5332 additional reserved-memory regions are used to improve
post mortem debugging. Thermal sensors (tsens) are added and zones
defined. The crypto engine is added, and support for the RDP454 board is
added.
Across MSM8916 and MSM8939 pinctrl state definitions are cleaned up and
the purpose of msm8939-pm8916 is documented. MSM8939 has regulator
definitions cleaned up, following to the previous effort on MSM8916.
CPU Bus Fabric scaling support is added to MSM8996 Pro.
On QCM2290 CPU idle states are added.
For QDU1000 SDHCI is introduced and enabled on the IDP to gain eMMC
support. IMEM and PIL information regions are defined for improved post
mortem debugging.
The Qualcomm Robotics RB2 kit gets its on-board buttons described.
A few fixes are introduced for the newly merged SC8180X, in particluar
the DisplayPort blocks are moved to the MMCX power domain to avoid power
being reduced prematurely during boot.
The SC8280XP GPU is added and enabled for the Lenovo Thinkpad X13s,
and resets for the soundwire controllers are added. The OUI is
specified for ethernet phys on SA8540P Ride platform, to avoid reset
issues.
Charger description is added to the PMI8998 PMIC and enabled across
OnePlus 6/6T, SHIFT SHIFT6mq and Xiaomi Pocophone F1.
On SM6350 CPU idle states and UART1 are added. And SM6375 gains GPU
clock controller and IOMMU definitions.
The Fairphone FP4 gains Bluetooth support.
SM8150 is transitioned to use 2 interconnect-cells, and the USB
interconnect path is described to ensure buses are adequately voted for.
The same changes are done for SM8250, and the resolution of the
static framebuffer on Sony Xperia 1 II and 5 II are corrected.
The USB bus paths are also added to SM8350, SM8450 and SM8550.
On SM8550 DisplayPort nodes are added, as is the PWM controller for
driving the notification LED and the RTC is enabled. For the MTP and QRD
boards, the soundcard and audio codecs are defined.
A Tegra change, related to LP855X binding changes, was accidentally
picked up and dropped again later.
A number of DeviceTree fixes identified through validation was
introduced as well. Additionally a few nodes got their default status
changed to avoid unnecessarily having to enable them (e.g. the mdp/dpu
node).
* tag 'qcom-arm64-for-6.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (94 commits)
Revert "arm64: dts: adapt to LP855X bindings changes"
arm64: dts: qcom: sc8280xp: Enable GPU related nodes
arm64: dts: qcom: sc8280xp: Add GPU related nodes
arm64: dts: qcom: msm8939-pm8916: Mark always-on regulators
arm64: dts: qcom: msm8939: Define regulator constraints next to usage
arm64: dts: qcom: msm8939-pm8916: Clarify purpose
arm64: dts: qcom: msm8939: Fix regulator constraints
arm64: dts: qcom: msm8939-sony-tulip: Allow disabling pm8916_l6
arm64: dts: qcom: msm8939-sony-tulip: Fix l10-l12 regulator voltages
arm64: dts: qcom: msm8939: Disable lpass_codec by default
arm64: dts: qcom: msm8939-pm8916: Add missing pm8916_codec supplies
arm64: dts: qcom: qrb4210-rb2: Enable on-board buttons
arm64: dts: qcom: msm8916: Drop msm8916-pins.dtsi
arm64: dts: qcom: msm8916/39: Rename wcnss pinctrl
arm64: dts: qcom: msm8916/39: Cleanup audio pinctrl
arm64: dts: qcom: apq8016-sbc: Drop unneeded MCLK pinctrl
arm64: dts: qcom: msm8916/39: Consolidate SDC pinctrl
arm64: dts: qcom: msm8916/39: Fix SD card detect pinctrl
arm64: dts: qcom: msm8996: rename labels for HDMI nodes
arm64: dts: qcom: sm8250: rename labels for DSI nodes
...
Link: https://lore.kernel.org/r/20230615162043.1461624-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Various small fixes and cleanups to be aligned with the latest dt-schema.
Other major changes are:
- Wire mali-400 gpu
- Change board name for zcu1275
- Use ethernet-phy-id to handle ETH phy reset properly
- Switch to amd.com emails
- Update people in DT bindings
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZIHGHgAKCRDKSWXLKUoM
IQW2AJ0eRZ5g7SYEg1y/zir6/j5s4RyaiACeO9EQJQ8nKkez73w4uoTBdmmOmlY=
=R8F0
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=jqDa
-----END PGP SIGNATURE-----
Merge tag 'zynqmp-dt-for-v6.5' of https://github.com/Xilinx/linux-xlnx into soc/dt
arm64: ZynqMP DT changes for v6.5
Various small fixes and cleanups to be aligned with the latest dt-schema.
Other major changes are:
- Wire mali-400 gpu
- Change board name for zcu1275
- Use ethernet-phy-id to handle ETH phy reset properly
- Switch to amd.com emails
- Update people in DT bindings
* tag 'zynqmp-dt-for-v6.5' of https://github.com/Xilinx/linux-xlnx: (33 commits)
dt-bindings: usb: xilinx: Replace Manish by Piyush
dt-bindings: xilinx: Remove Rajan, Jolly and Manish
arm64: zynqmp: Used fixed-partitions for QSPI in k26
arm64: zynqmp: Add pmu interrupt-affinity
arm64: zynqmp: Set qspi tx-buswidth to 4
arm64: zynqmp: Fix usb node drive strength and slew rate
arm64: zynqmp: Describe TI phy as ethernet-phy-id
arm64: zynqmp: Switch to amd.com emails
arm64: zynqmp: Convert kv260-revA overlay to ASCII text
dt-bindings: xilinx: Switch xilinx.com emails to amd.com
arm64: xilinx: Use zynqmp prefix for SOM dt overlays
arm64: zynqmp: Add phase tags marking
arm64: zynqmp: Describe bus-width for SD card on KV260
arm64: zynqmp: Enable AMS on SOM and other zcu10x boards
arm64: zynqmp: Enable DP driver for SOMs
arm64: zynqmp: Setup clock for DP and DPDMA
arm64: zynqmp: Switch to ethernet-phy-id in kv260
arm64: zynqmp: Disable USB3.0 for zc1751-xm016-dc2
arm64: zynqmp: Add pinctrl emmc description to SM-K26
arm64: zynqmp: Add gpio labels for modepin gpio
...
Link: https://lore.kernel.org/r/CAHTX3d+2s_KmCnd=x5hydGb+LYoznAzYGTizvqqN2NFmrBurfw@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Devicetree bindings document does not have to say in the title that
it is a "Devicetree binding", but instead just describe the hardware.
Most of these have been fixed already, so fix the handful that snuck in.
With this, a meta-schema check can be enabled to catch these
automatically.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20230615213154.1753313-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
This node's register space is not accessed by any other node, which
is the traditional use for the "syscon" hint. It looks to have been
added here to make use of a Linux kernel helper syscon_node_to_regmap().
The Linux driver now uses a more appropriate helper that does not
require the hint, so let's remove it from the binding.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230516184626.154892-2-afd@ti.com
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Cleanup bindings dropping unneeded quotes. Once all these are fixed,
checking for this can be enabled in yamllint. Also absolute path
starting with /schemas is preferred.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230609140751.65129-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The GPUCC block on SM6375 is powered by VDD_CX and VDD_GX. If the latter
rail is not online, GX_GDSC will never turn on. Describe the missing
handles.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230529-topic-sm6375gpuccpd-v1-1-8d57c41a6066@linaro.org
The LPASS (Low Power Audio Subsystem) Audio clock controller provides reset
support when it is under the control of Q6DSP.
Add support for those resets and adds IDs for clients to request the reset.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230608125315.11454-3-srinivas.kandagatla@linaro.org
The LPASS (Low Power Audio Subsystem) clock controller provides reset
support when it is under the control of Q6DSP.
Add support for those resets and adds IDs for clients to request the reset.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230608125315.11454-2-srinivas.kandagatla@linaro.org
Define clock/clock-names properties of the MMCC device node to be used
on MSM8226 platform.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230509-msm8226-mmcc-parents-v1-2-83a2dfc986ab@z3ntu.xyz
