ieee80211_tid_to_link_map_size_ok() validates negotiated TTLM elements
against the number of link-map entries indicated by link_map_presence.
ieee80211_parse_neg_ttlm() must consume the same layout.
The parser advanced its cursor for every TID, including TIDs whose
presence bit is clear and therefore have no map bytes in the element.
A sparse map can then make a later present TID read past the validated
element.
The bad bytes land in neg_ttlm->{up,down}link[tid] but are gated by
valid_links before being applied to driver state, so a peer cannot
turn the read into a policy change. Under KUnit + KASAN with an
exact-sized element allocation the OOB read is reported as a
slab-out-of-bounds; whether the same trigger fires under the
production RX path depends on surrounding allocator state.
Advance the cursor only when the current TID has a map present.
Fixes: 8f500fbc6c ("wifi: mac80211: process and save negotiated TID to Link mapping request")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Link: https://patch.msgid.link/20260515151719.1317659-2-michael.bommarito@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wilc_wlan_firmware_download() allocates dma_buffer with kmalloc() at
the top of the function and uses a 'fail:' label to free it via
kfree(dma_buffer) on error.
All later error paths correctly use 'goto fail' to route through this
cleanup. However, the early failure path after the first acquire_bus()
call uses a bare 'return ret;', which leaks dma_buffer whenever the bus
acquire fails.
Replace the early return with goto fail so the existing cleanup path
runs.
Found via a custom Coccinelle semantic patch hunting for kmalloc'd
locals leaked on early-return error paths in driver firmware-download
code.
Fixes: 1241c5650f ("wifi: wilc1000: Fill in missing error handling")
Signed-off-by: Shitalkumar Gandhi <shitalkumar.gandhi@cambiumnetworks.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260511042732.998311-1-shitalkumar.gandhi@cambiumnetworks.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_invoke_fast_rx() reads RX status through
IEEE80211_SKB_RXCB(skb), which aliases the same skb->cb storage
that ieee80211_rx_mesh_data() reuses as IEEE80211_TX_INFO. In the
unicast forward path, mesh_data does:
info = IEEE80211_SKB_CB(fwd_skb);
memset(info, 0, sizeof(*info));
on the same skb the caller still names via rx->skb, then either
queues the skb for TX (success) or kfree_skb()'s it (no-route)
before returning RX_QUEUED. The caller's RX_QUEUED arm then
calls sta_stats_encode_rate(status) on memory that is either
zeroed (success path) or freed (no-route path). The latter is
KASAN slab-use-after-free in ieee80211_prepare_and_rx_handle.
Fix by encoding the rate from status before invoking
ieee80211_rx_mesh_data(), so the RX_QUEUED arm consumes a value
captured while status was still backed by valid memory.
Fixes: 3468e1e0c6 ("wifi: mac80211: add mesh fast-rx support")
Cc: stable@vger.kernel.org
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260509043427.60322-2-enderaoelyther@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When parsing a beacon, mac80211 erroneously inherits any
reconfiguration or EPCS multi-link elements from the outer
elements into the multi-BSSID profile that's requested, if
connected to a non-transmitted BSS, unless that profile
has a non-inheritance element.
This also happens if parsing a multi-BSSID profile that
doesn't have a non-inheritance element.
Fix this by having an empty non-inheritance element so
cfg80211_is_element_inherited() is invoked in these cases
and causes the parser to skip the elements that should
never be inherited.
Fixes: cf36cdef10 ("wifi: mac80211: Add support for parsing Reconfiguration Multi Link element")
Fixes: 24711d60f8 ("wifi: mac80211: Support parsing EPCS ML element")
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://patch.msgid.link/20260508091032.92184c0a3f08.I3c43b0b63d2cef8a4ddddaef1c2faaeb1de711ad@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If either reconf or EPCS multi-link element (MLE) is contained in
a non-transmitted profile, the defragmentation routine is called
with a pointer to the defragmented copy, but the original elements.
This is incorrect for two reasons:
- if the original defragmentation was needed, it will not find the
correct data
- if the original frame is at a higher address, the parsing will
potentially overrun the heap data (though given the layout of
the buffers, only into the new defragmentation buffer, and then
it has to stop and fail once that's filled with copied data.
Fix it by tracking the container along with the pointer and in
doing so also unify the two almost identical defragmentation
routines.
Fixes: 4d70e9c548 ("wifi: mac80211: defragment reconfiguration MLE when parsing")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Link: https://patch.msgid.link/20260508091031.8a6c34613178.I4de16ebbce2d27f2f8f98fc49949c7a376c2fe8d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In client mode, the extended capabilities are handled by the kernel
looking at the association frame. When the supplicant installs the keys
it calls sta_apply_parameters and it doesn't include the extended
capabilities since those can't change after association.
As a result, we overrode the max_amsdu_subframes that we set after
association.
Check that the ext_capa coming from the user space is valid before
looking at it. If the ext_capa is NULL, it really means that the
extended capabilities are not changed (as opposed to cleared).
The default value for max_amsdu_subframes is 0, which means there is no
limit. This value is valid and in case the association response frame
does not have extended capabilities, this is the value we should use.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221079
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260513170623.828dbb58c782.Ifd2bfc190c26140e919127adb02ffddd7b551499@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE80211_MLE_STA_EPCS_CONTROL_LINK_ID is 0x000f, so link_id extracted
from a PRIO_ACCESS ML element PER_STA_PROFILE subelement can be 0..15.
sdata->link[] has IEEE80211_MLD_MAX_NUM_LINKS (15) entries (indices 0..14),
making index 15 out-of-bounds.
A connected WiFi 7 AP can trigger this by sending an EPCS Enable Response
action frame with a PER_STA_PROFILE subelement where link_id = 15. The
unsolicited-notification path (dialog_token = 0) is reachable any time
EPCS is already enabled, without any prior client request.
sdata->link[15] reads into the first word of sdata->activate_links_work
(a wiphy_work whose embedded list_head is non-NULL after INIT_LIST_HEAD),
so the NULL check on the result does not catch the invalid access. The
garbage pointer is then passed to ieee80211_sta_wmm_params(), which
dereferences link->sdata and crashes the kernel.
The same class of bug was fixed for ieee80211_ml_reconfiguration() by
commit 162d331d83 ("wifi: mac80211: bounds-check link_id in
ieee80211_ml_reconfiguration").
Fixes: de86c5f608 ("wifi: mac80211: Add support for EPCS configuration")
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260515102908.1653088-1-hossu.alexandru@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Start the numbering scheme for higher-level topology structures (like
socket, book, drawer) at zero, matching the convention for other hardware
identifiers like e.g. CPU numbers.
Hardware documentation, the Hardware Management Console and other tools
like zmemtopo also use zero-based numbering for these containing entities.
Aligning the numbering in sysfs, procfs, and tools like lscpu improves
user experience by making it easier to correlate topology information
across different interfaces.
If available, Linux on s390 derives this physical topology information from
the stsi function code 15 store_topology instruction, which is defined to
start at 1 for the lowest numbered container id. Subtract one, so
drawer_id, book_id and socket_id in cpu_topology[] start with 0 for the
lowest numbered entity; and /proc/cpuinfo and tools like 'lscpu -ye'
display the expected values.
Display only, no functional change intended.
Example: In a partition with 3 cores in a system with
8 cores per socket; 2 sockets per book; 4 books per dawer; and 4 drawers:
Before this fix:
$ lscpu -ye
CPU NODE DRAWER BOOK SOCKET CORE L1d:L1i:L2 ONLINE CONFIGURED POLARIZATION ADDRESS
0 0 2 4 1 0 0:0:0 yes yes vert-high 0
1 0 2 4 1 0 1:1:1 yes yes vert-high 1
2 0 2 4 1 1 2:2:2 yes yes vert-medium 2
3 0 2 4 1 1 3:3:3 yes yes vert-medium 3
4 0 2 4 2 3 4:4:4 yes yes vert-low 4
5 0 2 4 2 3 5:5:5 yes yes vert-low 5
After this fix:
$ lscpu -ye
CPU NODE DRAWER BOOK SOCKET CORE L1d:L1i:L2 ONLINE CONFIGURED POLARIZATION ADDRESS
0 0 1 3 0 0 0:0:0 yes yes vert-high 0
1 0 1 3 0 0 1:1:1 yes yes vert-high 1
2 0 1 3 0 1 2:2:2 yes yes vert-medium 2
3 0 1 3 0 1 3:3:3 yes yes vert-medium 3
4 0 1 3 1 3 4:4:4 yes yes vert-low 4
5 0 1 3 1 3 5:5:5 yes yes vert-low 5
For KVM guests, qemu emulates the stsi FC15 store_topology instruction.
This emulation currently erroneously starts id numbering at 0. A qemu fix
is proposed that makes this emulation compliant to the stsi architecture.
In case a guest with this patch is running on a qemu without the other fix,
it can happen that ids of 255 are displayed erroneously.
z/VM currently does not provide or emulate physical topology information to
its guests. So this patch does not change anything for z/VM guests.
Fixes: 10d3858950 ("[S390] topology: expose core identifier")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Acked-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
pKVM must validate the host-provided tracing buffer descriptor.
However, if an error is found, the hypervisor would just return 0 to the
host. Fix the return value on validation failure.
While at it, rename the function to hyp_trace_desc_is_valid() and skip
validation for the nVHE mode as we trust host-provided data in that
case.
Signed-off-by: Vincent Donnefort <vdonnefort@google.com>
Fixes: 680a04c333 ("KVM: arm64: Add tracing capability for the nVHE/pKVM hyp")
Link: https://lore.kernel.org/r/20260514162624.3477857-1-vdonnefort@google.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
Companion to commit 250f25367b ("KVM: arm64: Tear down vGIC on
failed vCPU creation"), which added the missing kvm_vgic_vcpu_destroy()
call to the kvm_share_hyp() failure path in kvm_arch_vcpu_create(). The
kvm_vgic_vcpu_init() failure path immediately above it has the same
shape and still needs the same cleanup.
Call kvm_vgic_vcpu_destroy() when kvm_vgic_vcpu_init() fails so private
IRQs allocated before a redistributor iodev registration failure are
released before the failed vCPU is freed.
Fixes: 03b3d00a70 ("KVM: arm64: vgic: Allocate private interrupts on demand")
Cc: stable@vger.kernel.org
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Yuan Yao <yaoyuan@linux.alibaba.com>
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Link: https://lore.kernel.org/r/20260519135042.2219239-1-michael.bommarito@gmail.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
Userspace can restore an ITS Device Table Entry whose Size field encodes
more EventID bits than the virtual ITS supports. The live MAPD path
rejects that state, but vgic_its_restore_dte() accepts it and stores the
out-of-range value in dev->num_eventid_bits.
Reject restored DTEs with num_eventid_bits > VITS_TYPER_IDBITS before
allocating the device. This mirrors the MAPD check and prevents the
restored state from reaching vgic_its_restore_itt(), where the unchecked
value can be converted into an oversized scan_its_table() range.
Fixes: 57a9a11715 ("KVM: arm64: vgic-its: Device table save/restore")
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Link: https://lore.kernel.org/r/20260519132519.2142458-1-michael.bommarito@gmail.com
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
commit bb88e8da00 ("erofs: use meta buffers for xattr operations")
converted xattr operations to use on-stack erofs_buf instances.
erofs_init_inode_xattrs() uses such a metabuf while reading the inline
xattr header and shared xattr id array.
Some error paths after erofs_read_metabuf() leave through out_unlock
without dropping the metabuf, so the folio reference can leak.
Consolidate the cleanup at out_unlock. erofs_put_metabuf() is a
no-op if no folio has been acquired, and this keeps all paths after
taking EROFS_I_BL_XATTR_BIT covered by a single cleanup site.
Fixes: bb88e8da00 ("erofs: use meta buffers for xattr operations")
Signed-off-by: Jia Zhu <zhujia.zj@bytedance.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Fixes: bb88e8da00 ("erofs: use meta buffers for xattr operations")
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
After unaligned compressed extents were introduced, the following race
could occur:
[Thread 1] [Thread 2]
(z_erofs_fill_bio_vec)
<handle a Z_EROFS_PREALLOCATED_FOLIO folio>
...
filemap_add_folio (1)
(z_erofs_bind_cache)
<the same folio is found..>
..
..
folio_attach_private (2)
filemap_add_folio (3) again
Since (1) is executed but (2) hasn't been executed yet, it's possible
that another thread finds the same managed folio in z_erofs_bind_cache()
for a different pcluster and calls filemap_add_folio() again since
folio->private is still Z_EROFS_PREALLOCATED_FOLIO.
Fix this by explicitly clearing folio->private before making the folio
visible in the managed cache so that another pcluster can simply wait
on the locked managed folio as what we did for other shared cases [1].
This only impacts unaligned data compression (`-E48bit` with zstd,
for example).
[1] Commit 9e2f9d34dd ("erofs: handle overlapped pclusters out of
crafted images properly") was originally introduced to handle crafted
overlapped extents, but it addresses unaligned extents as well.
Fixes: 7361d1e376 ("erofs: support unaligned encoded data")
Reported-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Closes: https://lore.kernel.org/r/4a2f3801-fac1-42fe-ae75-da315822e088@salutedevices.com
Tested-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
scarlett2_hwdep_write() rejects writes when offset + count is greater than
or equal to the selected flash segment size. That incorrectly treats a
write ending exactly at the end of the segment as out of space, although
the last byte written is still within the segment.
Split invalid argument checks from the segment-space check, keep
zero-length writes as no-ops, and compare count against the remaining
segment size. This permits exact-end writes and avoids relying on
offset + count before deciding whether the request is in bounds.
Fixes: 1abfbd3c95 ("ALSA: scarlett2: Add support for uploading new firmware")
Cc: stable@vger.kernel.org
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260519-alsa-scarlett2-flash-write-boundary-v1-1-b550480e92da@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the HP ProBook 440 G6, the HP ProBook 430 G6 needs
the ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF quirk for its
mute and microphone mute LEDs.
Tested on a HP ProBook 430 G6.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Link: https://patch.msgid.link/20260519140248.4211-2-mail@mariushoch.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pending irq work might be still floating while the assigned stream
has been already closed, which may lead to UAF, especially when
another async work for fasync is involved.
For addressing this, extend the hda_controller_ops for allowing the
extra cleanup procedure that is specific to the controller driver, and
make sure to cancel and sync the pending irq work at each PCM close
before releasing the resources.
Reported-by: Jake Lamberson <lamberson.jake@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260519121157.28477-2-tiwai@suse.de
Currently, the delayed IRQ handling for PCM streams is managed in a
single work embedded in hda_intel, but this is basically a per-stream
thing. Due to the single work, we can't cancel the work properly at
closing each stream, for example.
For making the IRQ pending work to be stream-based, this patch changes
the following:
- An extended version of azx_dev (i.e. the hd-audio stream object) is
defined for snd-hda-intel
- The irq_pending flag and irq_pending_work are moved to
hda_intel_stream, so that they can be hda-intel stream specific
- The stream creation and assignment are refactored so that
snd-hda-intel can handle individually;
the snd-hda-intel specific workaround for stream tags is also moved
to snd-hda-intel itself instead of the common code
- The irq pending work is canceled properly at free / shutdown
While we're at it, changed the bit field flag to bool, as the bit
field doesn't help much in our case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260519121157.28477-1-tiwai@suse.de
__bpf_dynptr_data() can return NULL (FILE dynptrs, any non-contiguous
backing). bpf_verify_pkcs7_signature() forwards the pointer to
verify_pkcs7_signature() unchecked, causing a NULL deref in
asn1_ber_decoder() reachable from a sleepable BPF LSM at lsm.s/bpf.
NULL-check both pointers and reject with -EINVAL. Mirrors the guards
already in kernel/bpf/crypto.c.
Fixes: 865b0566d8 ("bpf: Add bpf_verify_pkcs7_signature() kfunc")
Reported-by: Xianrui Dong <dongxianrui1@gmail.com>
Signed-off-by: KP Singh <kpsingh@kernel.org>
Reviewed-by: Amery Hung <ameryhung@gmail.com>
Acked-by: Song Liu <song@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20260520024059.313468-1-kpsingh@kernel.org
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
debugfs_lookup() returns a dentry with an elevated reference count that
must be released with dput(). The current code discards the returned
dentry without calling dput(), causing a reference leak on every
firmware reset recovery.
Additionally, when CONFIG_DEBUG_FS is disabled, debugfs_lookup()
returns ERR_PTR(-ENODEV), not NULL. The current check passes for error
pointers and would call dput() on an invalid pointer, causing a crash.
Fixes: bc90fbe0c3 ("pds_core: Rework teardown/setup flow to be more common")
Signed-off-by: Nikhil P. Rao <nikhil.rao@amd.com>
Link: https://patch.msgid.link/20260515212907.998028-3-nikhil.rao@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix two cases where pdsc_devcmd_wait() returns stale success from
the completion register instead of an error:
1. FW crash: If firmware stops running, the wait loop breaks early with
running=false. The condition "if ((!done || timeout) && running)" is
false, so error handling is bypassed and stale status is returned.
Check !running first and return -ENXIO.
2. Timeout: If a command times out, err is set to -ETIMEDOUT but then
overwritten by pdsc_err_to_errno(status) which reads stale status.
Return -ETIMEDOUT immediately after cleaning up.
Both errors now propagate to pdsc_devcmd_locked() which queues
health_work for recovery.
Fixes: 45d76f4929 ("pds_core: set up device and adminq")
Signed-off-by: Nikhil P. Rao <nikhil.rao@amd.com>
Link: https://patch.msgid.link/20260515212907.998028-1-nikhil.rao@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an internal review from Airoha, it was notice that the RX DMA descriptor
bits and mask are wrong. These values probably refer to an old NPU firmware
never published. The previous value works correctly but it was reported
that in some specific condition in mixed scenario with both Ethernet and
WiFi offload it's possible that RX DMA descriptor signal wrong value with
the problem to the RX ring or packets getting dropped.
To handle these specific scenario, apply the new suggested bits mask from
Airoha.
Correct functionality of both AN7581 NPU and MT7996 variant were verified
and confirmed working.
Fixes: a7fc8c641c ("net: airoha: Fix npu rx DMA definitions")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260518134530.3683-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
unix_stream_data_wait() does skb_peek_tail(&sk->sk_receive_queue) without
holding any lock that prevents SKBs on that queue from being dequeued and
freed.
This has been the case since commit 79f632c71b ("unix/stream: fix
peeking with an offset larger than data in queue").
The first consequence of this is that the pointer comparison
`tail != last` can be false even if `last` semantically refers to an
already-freed SKB while `tail` is a new SKB allocated at the same address;
which can cause unix_stream_data_wait() to wrongly keep blocking after new
data has arrived, but only in a weird scenario where a peeking recv() and
a normal recv() on the same socket are racing, which is probably not a
real problem.
But since commit 2b514574f7 ("net: af_unix: implement splice for stream
af_unix sockets"), `tail` is actually dereferenced, which can cause UAF in
the following race scenario (where test_setup() runs single-threaded,
and afterwards, test_thread1() and test_thread2() run concurrently in
two threads:
```
static int socks[2];
void test_setup(void) {
socketpair(AF_UNIX, SOCK_STREAM, 0, socks);
send(socks[1], "A", 1, 0);
int peekoff = 1;
setsockopt(socks[0], SOL_SOCKET, SO_PEEK_OFF, &peekoff, sizeof(peekoff));
}
void test_thread1(void) {
char dummy;
recv(socks[0], &dummy, 1, MSG_PEEK);
}
void test_thread2(void) {
char dummy;
recv(socks[0], &dummy, 1, 0);
shutdown(socks[1], SHUT_WR);
}
```
when racing like this:
```
thread1 thread2
unix_stream_read_generic
mutex_lock(&u->iolock)
skb_peek(&sk->sk_receive_queue)
skb_peek_next(skb, &sk->sk_receive_queue)
mutex_unlock(&u->iolock)
unix_stream_read_generic
unix_state_lock(sk)
skb_peek(&sk->sk_receive_queue)
unix_state_unlock(sk)
unix_stream_data_wait
unix_state_lock(sk)
tail = skb_peek_tail(&sk->sk_receive_queue)
spin_lock(&sk->sk_receive_queue.lock)
__skb_unlink(skb, &sk->sk_receive_queue)
spin_unlock(&sk->sk_receive_queue.lock)
consume_skb(skb) [frees the SKB]
`tail != last`: false
`tail`: true
`tail->len != last_len` ***UAF***
```
Fix the UAF by removing the read of tail->len; checking tail->len would
only make sense if SKBs in the receive queue of a UNIX socket could grow,
which can no longer happen.
Kuniyuki explained:
> When commit 869e7c6248 ("net: af_unix: implement stream sendpage
> support") added sendpage() support, data could be appended to the last
> skb in the receiver's queue.
>
> That's why we needed to check if the length of the last skb was changed
> while waiting for new data in unix_stream_data_wait().
>
> However, commit a0dbf5f818 ("af_unix: Support MSG_SPLICE_PAGES") and
> commit 57d44a354a ("unix: Convert unix_stream_sendpage() to use
> MSG_SPLICE_PAGES") refactored sendmsg(), and now data is always added
> to a new skb.
That means this fix is not suitable for kernels before 6.5.
Fixes: 2b514574f7 ("net: af_unix: implement splice for stream af_unix sockets")
Cc: stable@vger.kernel.org # 6.5.x
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20260518-b4-unix-recv-wait-hotfix-v2-1-83e29ce8ad31@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reported by Sashiko:
The function ipv6_hop_ioam() accesses
__in6_dev_get(skb->dev)->cnf.ioam6_enabled without validating the returned
idev pointer. Because addrconf_ifdown() can concurrently clear dev->ip6_ptr
via RCU, __in6_dev_get() can return NULL during interface teardown, which
could cause a NULL pointer dereference when processing an IOAM Hop-by-Hop
option.
Let's add a check and use SKB_DROP_REASON_IPV6DISABLED accordingly.
Fixes: 9ee11f0fff ("ipv6: ioam: Data plane support for Pre-allocated Trace")
Cc: stable@vger.kernel.org
Signed-off-by: Justin Iurman <justin.iurman@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260517183059.29140-1-justin.iurman@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nicolai Buchwitz says:
====================
net: phy: honor eee_disabled_modes when advertising EEE
While debugging why ethtool --show-eee reports "not supported" on a
Raspberry Pi CM4 with eee-broken-1000t / eee-broken-100tx set on the
PHY node, I noticed two phylib helpers copy phydev->supported_eee
into phydev->advertising_eee without applying
phydev->eee_disabled_modes: phy_support_eee() and
phy_advertise_eee_all(). That undoes the filtering phy_probe() set
up after of_set_phy_eee_broken(), so the PHY ends up advertising EEE
for modes that were marked broken in DT (or by the driver via
eee_disabled_modes).
The visible effect on MAC drivers that call phy_support_eee() after
probe (bcmgenet, fec, lan743x, lan78xx, r8169) is that ethtool on the
local interface reports "not supported" (because supported is masked
by eee_disabled_modes and ends up empty), while the link partner
happily sees EEE negotiated and active.
Patch 1 fixes phy_support_eee(). Patch 2 fixes phy_advertise_eee_all(),
which is also reached from genphy_c45_ethtool_set_eee() when user
space passes an empty advertisement.
I went through the other users of supported_eee as suggested by Andrew
and they look fine:
- phy_probe() already masks via eee_disabled_modes after
of_set_phy_eee_broken().
- genphy_c45_ethtool_get_eee() masks supported_eee with
eee_disabled_modes when reporting to user space.
- genphy_c45_ethtool_set_eee() masks user-supplied adv against
eee_disabled_modes, and the empty-adv path is now covered by
patch 2.
- genphy_c45_read_eee_abilities(), read_eee_cap1/cap2 populate
supported_eee from PHY registers (source of truth).
- genphy_c45_read_eee_adv(), read_eee_lpa() and write_eee_adv() use
supported_eee only to gate which MMD registers to access, not to
construct an advertisement.
====================
Link: https://patch.msgid.link/20260518-devel-phy-support-eee-fix-v2-0-05b52626fa68@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
phy_advertise_eee_all() copies supported_eee into advertising_eee
unconditionally, overwriting any filtering applied during phy_probe()
based on DT eee-broken-* properties or driver-populated
eee_disabled_modes. genphy_c45_ethtool_set_eee() calls this helper
when user space passes an empty advertisement, undoing the filtering.
Apply the same eee_disabled_modes mask in phy_advertise_eee_all() so
the filtering survives the copy, matching the pattern in phy_probe()
and phy_support_eee().
Fixes: b64691274f ("net: phy: add helper phy_advertise_eee_all")
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260518-devel-phy-support-eee-fix-v2-2-05b52626fa68@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
phy_support_eee() copies supported_eee into advertising_eee
unconditionally, overwriting any filtering applied during phy_probe()
based on DT eee-broken-* properties or driver-populated
eee_disabled_modes. MAC drivers that call phy_support_eee() after
probe (e.g. bcmgenet, fec, lan743x, lan78xx, r8169) then cause the PHY
to advertise EEE for modes the user marked as broken.
The symptom is that ethtool --show-eee on the local interface reports
"not supported" (supported & ~eee_disabled_modes is empty) while the
link partner sees EEE negotiated and active.
phy_probe() already filters advertising_eee via eee_disabled_modes
after calling of_set_phy_eee_broken(). Apply the same mask in
phy_support_eee() so the filtering survives the copy.
Fixes: 49168d1980 ("net: phy: Add phy_support_eee() indicating MAC support EEE")
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260518-devel-phy-support-eee-fix-v2-1-05b52626fa68@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
genphy_c45_an_config_eee_aneg() writes the EEE advertisement to the
auto-negotiation device's MMD register space (MDIO_MMD_AN, register
MDIO_AN_EEE_ADV). These registers are read by the link partner only
during auto-negotiation, so writing them while autoneg is disabled
cannot influence the link. On some PHYs (e.g. Broadcom BCM54213PE)
the write nevertheless reaches the chip and disturbs the receive
datapath.
Concretely, running
ethtool -s eth0 speed 100 duplex full autoneg off
ethtool --set-eee eth0 eee off
leaves eth0 with TX working and RX completely silent on a
Raspberry Pi 4 / CM4 board (bcmgenet + BCM54213PE in rgmii-rxid).
Switching back to autoneg recovers the link.
Prior to commit f26a29a038 ("net: phy: ensure that genphy_c45_an_config_eee_aneg() sees new value of phydev->eee_cfg.eee_enabled"),
the disable path was effectively a no-op because the helper read
the stale eee_cfg.eee_enabled, so the underlying PHY behavior never
surfaced.
Bisected on rpi-6.12.y between commits 83943264 (good) and
effcbc88 (bad) to f26a29a038.
Fixes: f26a29a038 ("net: phy: ensure that genphy_c45_an_config_eee_aneg() sees new value of phydev->eee_cfg.eee_enabled")
Cc: stable@vger.kernel.org
Signed-off-by: Nerijus Bendžiūnas <nerijus.bendziunas@gmail.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Tested-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260516150251.879680-1-nerijus.bendziunas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel says:
====================
bridge: mcast: Fix a possible use-after-free when removing a bridge port
Patch #1 fixes a possible use-after-free when removing a bridge port.
Patch #2 adds a test case that triggers the problem.
In net-next we can:
1. Add DEBUG_NET_WARN_ON_ONCE() when a port multicast context is
de-initialized while enabled.
2. When de-initializing a port multicast context, synchronously shutdown
all the timers that were initialized when the context was initialized.
====================
Link: https://patch.msgid.link/20260517121122.188333-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test toggling of multicast snooping when per-VLAN multicast snooping is
enabled. The test always passes, but without "bridge: mcast: Fix
possible use-after-free when removing a bridge port" it results in a
splat.
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260517121122.188333-3-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When per-VLAN multicast snooping is enabled, the bridge iterates over
all the bridge ports, disables the per-port multicast context on each
port and enables the per-{port, VLAN} multicast contexts instead. The
reverse happens when per-VLAN multicast snooping is disabled.
When global multicast snooping is enabled, the bridge iterates over all
the bridge ports and enables the per-port multicast context on each
port. The reverse happens when multicast snooping is disabled.
The above scheme can result in a situation where both types of contexts
(per-port and per-{port, VLAN}) are enabled on a single bridge port:
# ip link add name br1 up type bridge mcast_snooping 1 mcast_querier 1 vlan_filtering 1
# ip link add name dummy1 up master br1 type dummy
# ip link set dev br1 type bridge mcast_vlan_snooping 1
# ip link set dev br1 type bridge mcast_snooping 0
# ip link set dev br1 type bridge mcast_snooping 1
This is not intended and it is a problem since the commit cited below.
Prior to this commit, when removing a bridge port,
br_multicast_disable_port() would disable the per-port multicast context
and the per-{port, VLAN} multicast contexts would get disabled when
flushing VLANs.
After this commit, br_multicast_disable_port() only disables the
per-port multicast context if per-VLAN multicast snooping is disabled.
If both types of contexts were enabled on the port when it was removed,
the per-port multicast context would remain enabled when freeing the
bridge port, leading to a use-after-free [1].
Fix by preventing the bridge from enabling / disabling the per-port
multicast contexts when toggling global multicast snooping if per-VLAN
multicast snooping is enabled.
[1]
ODEBUG: free active (active state 0) object: ffff88810f8bda78 object type: timer_list hint: br_ip6_multicast_port_query_expired (net/bridge/br_multicast.c:1927)
WARNING: lib/debugobjects.c:629 at debug_print_object+0x1b1/0x3e0, CPU#5: swapper/5/0
[...]
Call Trace:
<IRQ>
__debug_check_no_obj_freed (lib/debugobjects.c:1116)
kfree (mm/slub.c:2620 mm/slub.c:6250 mm/slub.c:6565)
kobject_cleanup (lib/kobject.c:689)
rcu_do_batch (kernel/rcu/tree.c:2617)
rcu_core (kernel/rcu/tree.c:2869)
handle_softirqs (kernel/softirq.c:622)
__irq_exit_rcu (kernel/softirq.c:656 kernel/softirq.c:496 kernel/softirq.c:735)
irq_exit_rcu (kernel/softirq.c:752)
sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1061 (discriminator 47) arch/x86/kernel/apic/apic.c:1061 (discriminator 47))
</IRQ>
Fixes: 4b30ae9adb ("net: bridge: mcast: re-implement br_multicast_{enable, disable}_port functions")
Reported-by: syzbot+ae231e0552fa77b26ea1@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/87qznowlfs.ffs@tglx/
Reported-by: Thomas Gleixner <tglx@kernel.org>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20260517121122.188333-2-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
otx2_pool_aq_init() frees pool->stack when mailbox sync or retry
allocation fails, but leaves the pointer unchanged. Later,
otx2_sq_aura_pool_init() unwinds the partial setup through
otx2_aura_pool_free(), which frees pool->stack again. The CN20K-specific
cn20k_pool_aq_init() implementation has the same bug in
its corresponding error path.
Set pool->stack to NULL immediately after the local free so the shared
cleanup path does not free the same stack again while cleaning up
partially initialized pool state.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still present in
v7.1-rc3.
Runtime validation was not performed because reproducing this path
requires OcteonTX2/CN20K hardware.
Fixes: caa2da34fd ("octeontx2-pf: Initialize and config queues")
Fixes: d322fbd172 ("octeontx2-pf: Initialize cn20k specific aura and pool contexts")
Cc: stable@vger.kernel.org
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Signed-off-by: Dawei Feng <dawei.feng@seu.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260515151826.1005397-1-dawei.feng@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
of_count_phandle_with_args() returns the count on success and a negative
errno on failure, including -ENOENT when the "pairsets" property is
absent. The existing comparison in of_load_pse_pis() checks against
ENOENT (positive 2) instead of -ENOENT, so the branch is taken for any
error return: legitimate DTs that omit "pairsets" trigger a spurious
"wrong number of pairsets" error and probe fails with -EINVAL.
Compare against -ENOENT so a missing "pairsets" property is correctly
treated as "this PI has no pairsets, continue".
Fixes: 9be9567a7c ("net: pse-pd: Add support for PSE PIs")
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20260515143103.1721888-1-jelonek.jonas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the error path of rtrs_srv_create_path_files(), the sysfs root folders
may already have been created and srv_path->kobj may already have been
initialized. If a later step fails, the cleanup currently calls
kobject_put(&srv_path->kobj) before
rtrs_srv_destroy_once_sysfs_root_folders(srv_path).
kobject_put() may drop the last reference to srv_path->kobj and invoke the
release callback, rtrs_srv_release(), which frees srv_path. The following
call to rtrs_srv_destroy_once_sysfs_root_folders(srv_path) then
dereferences srv_path internally to access srv_path->srv, resulting in a
use-after-free.
This failure path is reached before rtrs_srv_create_path_files() returns
success, so the successful-path lifetime handling is not involved.
Fix this by destroying the sysfs root folders before calling
kobject_put(&srv_path->kobj), so srv_path is still valid while the helper
accesses it.
This issue was found by a static analysis tool I am developing.
Fixes: ae4c81644e ("RDMA/rtrs-srv: Rename rtrs_srv_sess to rtrs_srv_path")
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Link: https://patch.msgid.link/20260514113834.865530-1-lgs201920130244@gmail.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Report max_msg_sz for mana_ib, which is 16MB.
Fixes: 4bda1d5332 ("RDMA/mana_ib: Implement port parameters")
Signed-off-by: Shiraz Saleem <shirazsaleem@microsoft.com>
Signed-off-by: Konstantin Taranov <kotaranov@microsoft.com>
Link: https://patch.msgid.link/20260512094209.264955-1-kotaranov@linux.microsoft.com
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Sashiko points out the legacy write path in ib_uverbs_write() does
allocate a struct uverbs_attr_bundle, but it doesn't wrap it in a
bundle_priv so downcasting here isn't safe.
Instead lift the method_elm out of the bundle_priv and use it for the
debug function. The legacy write path will leave it set as NULL since the
write method_elm uses a different type.
Cc: stable@vger.kernel.org
Fixes: 1de9287ece ("RDMA: Add ib_copy_validate_udata_in()")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
It was incorrect to place them in uverbs_ioctl because that makes every
driver depends on ib_uverbs.ko, which is undesired. ib_core_uverbs.c is
for functions used by alot of drivers that are linked into ib_core
instead.
Fixes: 1de9287ece ("RDMA: Add ib_copy_validate_udata_in()")
Link: https://patch.msgid.link/r/1-v1-045258567bd6+9fe-ib_uverbs_support_ko_jgg@nvidia.com
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Commit 0a869409a9 ("ACPI: battery: Convert the driver to a platform
one") changed the parent of the battery wakeup source to the platform
device used for driver binding, but it forgot to update the
acpi_pm_wakeup_event() call in acpi_battery_update() accordingly.
Do it now to unbreak waking up the system on critical battery status
during suspend-to-idle and during transitions to ACPI S3/S4.
Fixes: 0a869409a9 ("ACPI: battery: Convert the driver to a platform one")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 7.0+ <stable@vger.kernel.org> # 7.0+
Link: https://patch.msgid.link/12898712.O9o76ZdvQC@rafael.j.wysocki
-----BEGIN PGP SIGNATURE-----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=yDvf
-----END PGP SIGNATURE-----
Merge tag 'lsm-pr-20260519' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm
Pull lsm fix from Paul Moore:
"A single LSM patch to add a missing credential mutex lock to the
lsm_set_self_attr(2) syscall so it behaves similar to the associated
procfs API and avoids issues with ptrace"
* tag 'lsm-pr-20260519' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
lsm: hold cred_guard_mutex for lsm_set_self_attr()
- Make sure that the issuing of a deferred non-NCQ command via
workqueue feature is only used when mixing NCQ and non-NCQ commands
to the same link (i.e. return value ATA_DEFER_LINK), and nothing
else. This way we will not incorrectly try to use the feature for
e.g. PATA drivers.
- The deferred non-NCQ command was stored in a per-port struct.
When using Port Multipliers with FIS-Based Switching, we would thus
needlessly defer commands to all other links. Store the deferred QC
in a per-link struct, such that Port Multipliers with FBS will get
the same performance as before.
- The issuing of a deferred non-NCQ command via workqueue feature
broke support for Port Multipliers using Command-Based Switching.
The issuing of a deferred non-NCQ command via workqueue feature is
not compatible with the use of ap->excl_link, which PMPs with CBS
use for fairness (using implicit round robin).
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRN+ES/c4tHlMch3DzJZDGjmcZNcgUCagyJuQAKCRDJZDGjmcZN
clYrAP9WGyaktaHe8MVLFAOIvtj58qAyDGH5U9gqA/lc8MfFDQEAvC81OBtXkpP6
WaZGuAw6eqja1KlSg6mzmfOLvVIHLwk=
=MbtN
-----END PGP SIGNATURE-----
Merge tag 'ata-7.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata fixes from Niklas Cassel:
- Make sure that the issuing of a deferred non-NCQ command via
workqueue feature is only used when mixing NCQ and non-NCQ commands
to the same link (i.e. return value ATA_DEFER_LINK), and nothing
else. This way we will not incorrectly try to use the feature for
e.g. PATA drivers
- The deferred non-NCQ command was stored in a per-port struct. When
using Port Multipliers with FIS-Based Switching, we would thus
needlessly defer commands to all other links. Store the deferred QC
in a per-link struct, such that Port Multipliers with FBS will get
the same performance as before
- The issuing of a deferred non-NCQ command via workqueue feature broke
support for Port Multipliers using Command-Based Switching. The
issuing of a deferred non-NCQ command via workqueue feature is not
compatible with the use of ap->excl_link, which PMPs with CBS use for
fairness (using implicit round robin)
* tag 'ata-7.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: libata-scsi: do not needlessly defer commands when using PMP with FBS
ata: libata-scsi: do not use the deferred QC feature on PMPs with CBS
ata: libata-scsi: do not use the deferred QC feature for ATA_DEFER_PORT
ata: libata-scsi: improve readability of ata_scsi_qc_issue()
Vishal reported that KVM unit test 'x2apic' started failing after commit
0e98eb1481 ("entry: Prepare for deferred hrtimer rearming").
The reason is that KVM/VMX is injecting interrupts while it has interrupts
disabled, for a context that will enable interrupts, this means that
regs->flags.X86_EFLAGS_IF == 0 and irqentry_exit() will not do the right
thing.
Notably, irqentry_exit() must not call hrtimer_rearm_deferred() when the return
context does not have IF set, because this will cause problems vs NMIs.
Therefore, fix up the state after the injection.
Fixes: 0e98eb1481 ("entry: Prepare for deferred hrtimer rearming")
Reported-by: "Verma, Vishal L" <vishal.l.verma@intel.com>
Suggested-by: Thomas Gleixner <tglx@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Tested-by: "Verma, Vishal L" <vishal.l.verma@intel.com>
Tested-by: David Woodhouse <dwmw@amazon.co.uk>
Tested-by: Zhao Liu <zhao1.liu@intel.com>
Tested-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Binbin Wu <binbin.wu@linux.intel.com>
Link: https://patch.msgid.link/20260423155936.957351833@infradead.org
Closes: https://lore.kernel.org/r/70cd3e97fbb796e2eb2ff8cd4b7614ada05a5f24.camel%40intel.com
Move the VMX interrupt dispatch magic into the x86 core code. This
isolates KVM from the FRED/IDT decisions and reduces the amount of
EXPORT_SYMBOL_FOR_KVM().
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Tested-by: "Verma, Vishal L" <vishal.l.verma@intel.com>
Tested-by: Zhao Liu <zhao1.liu@intel.com>
Tested-by: Zhao Liu <zhao1.liu@intel.com>
Tested-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Binbin Wu <binbin.wu@linxu.intel.com>
Acked-by: Sean Christopherson <seanjc@google.com>
Link: https://patch.msgid.link/20260508091829.GO3126523@noisy.programming.kicks-ass.net
bio_integrity_verify() expects the passed struct bvec_iter to be an
iterator over bio data, not integrity. So construct a separate data
bvec_iter without the bio_integrity_bytes() conversion and pass it to
bio_integrity_verify() instead of bip_iter.
Fixes: 0bde8a12b5 ("block: add fs_bio_integrity helpers")
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20260513182924.1753582-1-csander@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=TmyE
-----END PGP SIGNATURE-----
Merge tag 'v7.1-rc4-ksmbd-server-fixes' of git://git.samba.org/ksmbd
Pull smb server fixes from Steve French:
- Fix two null pointer dereferences and a memory leak
* tag 'v7.1-rc4-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: fix null pointer dereference in compare_guid_key()
ksmbd: fix null pointer dereference in proc_show_files()
ksmbd: fix SID memory leak in set_posix_acl_entries_dacl() on overflow
- Check the index depth limit via ntfs_icx_parent_inc(), avoiding context
corruption from excessively deep child chains.
- Switch security descriptor allocation to kzalloc() to avoid leaking
uninitialized memory.
- Prevent an inconsistent state where vol->volume_label becomes NULL on
allocation failure.
- Validate MFT records by verifying that attrs_offset sits within
bytes_in_use.
- Fix an off-by-one boundary comparison, correctly catching the
out-of-range MFT record number
- Validate the attribute name offset and length bounds prior to AT_UNUSED
enumeration.
- Check for a valid left neighbor before runlist merges to prevent an
8byte out-of-bounds write on crafted volumes.
- Add the missing record comparison against $MFTMirr during mount.
- Fix wrong inode lookup when writing extent MFT records.
- Redirty folio on memory allocation failure in ntfs_write_mft_block().
- Capture and propagate $MFTMirr sync errors during writeback.
- Ensure MFT mirror and synchronous writes wait for I/O completion.
- Fix buffer overflow/heap over-read in ntfs_bdev_write() when cluster
size is smaller than PAGE_SIZE.
- Fix use-after-free in ntfs_inode_sync_filename() when parent index inode
is evicted while still holding its mrec_lock.
- Update resident attribute length validation to match $AttrDef.
- Fix refcount underflow and UAF of the global upcase table.
- Fix two smatch warnings.
-----BEGIN PGP SIGNATURE-----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=NZAT
-----END PGP SIGNATURE-----
Merge tag 'ntfs-for-7.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/ntfs
Pull ntfs fixes from Namjae Jeon:
- Check the index depth limit via ntfs_icx_parent_inc(), avoiding
context corruption from excessively deep child chains
- Switch security descriptor allocation to kzalloc() to avoid leaking
uninitialized memory
- Prevent an inconsistent state where vol->volume_label becomes NULL on
allocation failure
- Validate MFT records by verifying that attrs_offset sits within
bytes_in_use
- Fix an off-by-one boundary comparison, correctly catching the
out-of-range MFT record number
- Validate the attribute name offset and length bounds prior to
AT_UNUSED enumeration
- Check for a valid left neighbor before runlist merges to prevent an
8byte out-of-bounds write on crafted volumes
- Add the missing record comparison against $MFTMirr during mount
- Fix wrong inode lookup when writing extent MFT records
- Redirty folio on memory allocation failure in ntfs_write_mft_block()
- Capture and propagate $MFTMirr sync errors during writeback
- Ensure MFT mirror and synchronous writes wait for I/O completion
- Fix buffer overflow/heap over-read in ntfs_bdev_write() when cluster
size is smaller than PAGE_SIZE
- Fix use-after-free in ntfs_inode_sync_filename() when parent index
inode is evicted while still holding its mrec_lock
- Update resident attribute length validation to match $AttrDef
- Fix refcount underflow and UAF of the global upcase table
- Fix two smatch warnings
* tag 'ntfs-for-7.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/ntfs:
ntfs: restore $MFT mirror contents check
ntfs: fix empty_buf and ra lifetime bugs in ntfs_empty_logfile()
ntfs: validate attribute name bounds before returning it
ntfs: fix MFT bitmap scan 2^32 boundary check
ntfs: validate MFT attrs_offset against bytes_in_use
ntfs: fix missing kstrdup() error check in ntfs_write_volume_label()
ntfs: avoid leaking uninitialised bytes in new security descriptors
ntfs: fix out-of-bounds write in ntfs_index_walk_down()
ntfs: fix out-of-bounds write in ntfs_rl_collapse_range() merge path
ntfs: fix variable dereferenced before check ni in ntfs_attr_open()
ntfs: fix default_upcase refcount underflow and UAF on fs_context teardown
ntfs: match ntfs_resident_attr_min_value_length with $AttrDef
ntfs: avoid use-after-free of index inode in ntfs_inode_sync_filename()
ntfs: fix copy length in ntfs_bdev_write() for non-page-aligned start
ntfs: wait for sync mft writes to complete
ntfs: capture mft mirror sync errors in ntfs_write_mft_block()
ntfs: redirty folio when ntfs_write_mft_block() runs out of memory
ntfs: use base mft_no when looking up base inode for extent record
ntfs: fix variable dereferenced before check ni and attr in ntfs_attrlist_entry_add()
- modpost: prevent stack buffer overflow in do_input_entry() and do_dmi_entry()
Defensively replace unbound sprintf() calls in file2alias to prevent
silent stack overflows and detect alias name overflows with proper
error message.
- kbuild: pacman-pkg: make "rc" releases adhere to pacman versioning scheme
Enable smooth upgrades from "rc" releases w/ pacman packages.
Cc: Hasan Basbunar <basbunarhasan@gmail.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Thomas Weißschuh <linux@weissschuh.net>
Cc: Viktor Jägersküpper <viktor_jaegerskuepper@freenet.de>
-----BEGIN PGP SIGNATURE-----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=4PGV
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-7.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux
Pull Kbuild fixes from Nicolas Schier:
- modpost: prevent stack buffer overflow in do_input_entry() and
do_dmi_entry()
Defensively replace unbound sprintf() calls in file2alias to prevent
silent stack overflows and detect alias name overflows with proper
error message.
- kbuild: pacman-pkg: make "rc" releases adhere to pacman versioning
scheme
Enable smooth upgrades from "rc" releases w/ pacman packages.
* tag 'kbuild-fixes-7.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: pacman-pkg: make "rc" releases adhere to pacman versioning scheme
modpost: prevent stack buffer overflow in do_input_entry() and do_dmi_entry()
Well mostly the same issues the other code had as well:
1. Memory allocation while holding the userq_mutex lock is forbidden!
2. Things were created/started/published in the wrong order.
3. The reset lock was taken in the wrong order and seems to be
unecessary in the first place.
4. Error messages on invalid input parameters can spam the logs.
5. Error messages on memory allocation failures are usually superflous
as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 89e50de565)
In handle_read_data() the encrypted/folioq branch
(buf_len <= data_offset, reached via receive_encrypted_read for
transform PDUs > CIFSMaxBufSize + MAX_HEADER_SIZE) copies the READ
payload using buffer_len rather than data_len:
rdata->result = cifs_copy_folioq_to_iter(buffer, buffer_len,
cur_off,
&rdata->subreq.io_iter);
...
rdata->got_bytes = buffer_len;
buffer_len comes from the SMB3 transform header OriginalMessageSize
field (OriginalMessageSize - read_rsp_size); it represents the size
of the decrypted message after the SMB2 header. data_len comes from
the SMB2 READ response DataLength field; it represents the actual
READ payload size and may be smaller than buffer_len when the
decrypted message contains padding or other trailing bytes after the
READ payload. The existing check `data_len > buffer_len - pad_len`
only enforces an upper bound, so a server that emits
OriginalMessageSize larger than read_rsp_size + pad_len + data_len
passes the check and the kernel copies buffer_len bytes per response,
ignoring the server-asserted DataLength.
Two observable failures with a crafted server (DataLength=4,
buffer_len=20000):
- the kernel returns 20000 bytes per sub-request to userspace and
sets got_bytes = buffer_len, even though the response claimed
only 4 bytes of payload;
- on a partial netfs sub-request whose iterator is sized to
data_len, the over-large copy_folio_to_iter() short-reads,
cifs_copy_folioq_to_iter() returns -EIO via the n != len path,
and the entire netfs read collapses to -EIO even though the
leading sub-requests succeeded.
Use data_len for the copy length and for got_bytes so the kernel
honours the server-asserted READ payload size. For well-formed
servers (where buffer_len == pad_len + data_len) the change is
behaviour-equivalent.
Cc: stable@vger.kernel.org
Signed-off-by: Jeremy Erazo <mendozayt13@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
'evergreen_surface_check' is called with a NULL warning prefix when
handling potentially recoverable issues or just to compute the alignment
requirements, and 'evergreen_surface_check' is called again in case of
failure (with the correct prefix, as opposed to NULL), therefore, the
initial check must not print a warning, because the surface may be
accepted successfully after having been corrected, however if it isn't,
the final check will print the warning anyway. The surface check
functions specific to array modes already implement this behavior, but
the 'evergreen_surface_check' function itself doesn't.
This is also supposed to fix the "'%s' directive argument is null
[-Werror=format-overflow=]" compiler warning.
Fixes: 285484e2d5 ("drm/radeon: add support for evergreen/ni tiling informations v11")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vitaliy Triang3l Kuzmin <ml@triang3l.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit e20ea411c9)
Multiple queues needs these bo_va objects belonging to
the same uq_mgr. So once they are mapped lets not unmap
them as at any point of time any of the queues might be
using it.
Also userq_va_mapped should be a boolean than atomic.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 5c02889ea2)
