Export __dpll_pin_change_ntf() so that drivers can send pin change
notifications from within pin callbacks, which are already called
under dpll_lock. Using dpll_pin_change_ntf() in that context would
deadlock.
Add lockdep_assert_held() to catch misuse without the lock held.
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-9-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
SMA and U.FL pins share physical signal paths in pairs (SMA1/U.FL1 and
SMA2/U.FL2) controlled by the PCA9575 GPIO expander. Each pair can
only have one active pin at a time: SMA1 output and U.FL1 output share
the same CGU output, SMA2 input and U.FL2 input share the same CGU
input. The PCA9575 register bits determine which connector in each
pair owns the signal path.
The driver does not account for this pairing in two places:
ice_dpll_ufl_pin_state_set() modifies PCA9575 bits and disables the
backing CGU pin without checking whether the U.FL pin is currently
active. Disconnecting an already inactive U.FL pin flips bits that
the paired SMA pin relies on, breaking its connection.
ice_dpll_sma_direction_set() does not propagate direction changes to
the paired U.FL pin. For SMA2/U.FL2 the ICE_SMA2_UFL2_RX_DIS bit is
never managed, so U.FL2 stays disconnected after SMA2 switches to
output. For both pairs the backing CGU pin of the U.FL side is never
enabled when a direction change activates it, so userspace sees the
pin as disconnected even though the routing is correct.
Fix by guarding the U.FL disconnect path against inactive pins and by
updating the paired U.FL pin fully on SMA direction changes: manage
ICE_SMA2_UFL2_RX_DIS for the SMA2/U.FL2 pair and enable the backing
CGU pin whenever the peer becomes active.
Fixes: 2dd5d03c77 ("ice: redesign dpll sma/u.fl pins control")
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-8-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The DPLL SMA/U.FL pin redesign introduced ice_dpll_sw_pin_frequency_get()
which gates frequency reporting on the pin's active flag. This flag is
determined by ice_dpll_sw_pins_update() from the PCA9575 GPIO expander
state. Before the redesign, SMA pins were exposed as direct HW
input/output pins and ice_dpll_frequency_get() returned the CGU
frequency unconditionally — the PCA9575 state was never consulted.
The PCA9575 powers on with all outputs high, setting ICE_SMA1_DIR_EN,
ICE_SMA1_TX_EN, ICE_SMA2_DIR_EN and ICE_SMA2_TX_EN. Nothing in the
driver writes the register during initialization, so
ice_dpll_sw_pins_update() sees all pins as inactive and
ice_dpll_sw_pin_frequency_get() permanently returns 0 Hz for every
SW pin.
Fix this by writing a default SMA configuration in
ice_dpll_init_info_sw_pins(): clear all SMA bits, then set SMA1 and
SMA2 as active inputs (DIR_EN=0) with U.FL1 output and U.FL2 input
disabled. Each SMA/U.FL pair shares a physical signal path so only
one pin per pair can be active at a time. U.FL pins still report
frequency 0 after this fix: U.FL1 (output-only) is disabled by
ICE_SMA1_TX_EN which keeps the TX output buffer off, and U.FL2
(input-only) is disabled by ICE_SMA2_UFL2_RX_DIS. They can be
activated by changing the corresponding SMA pin direction via dpll
netlink.
Fixes: 2dd5d03c77 ("ice: redesign dpll sma/u.fl pins control")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-7-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
On certain E810 configurations where firmware supports Tx scheduler
topology switching (tx_sched_topo_comp_mode_en), ice_cfg_tx_topo()
may need to apply a new 5-layer or 9-layer topology from the DDP
package. If the AQ command to set the topology fails (e.g. due to
invalid DDP data or firmware limitations), the global configuration
lock must still be cleared via a CORER reset.
Commit 86aae43f21 ("ice: don't leave device non-functional if Tx
scheduler config fails") correctly fixed this by refactoring
ice_cfg_tx_topo() to always trigger CORER after acquiring the global
lock and re-initialize hardware via ice_init_hw() afterwards.
However, commit 8a37f9e2ff ("ice: move ice_deinit_dev() to the end
of deinit paths") later moved ice_init_dev_hw() into ice_init_hw(),
breaking the reinit path introduced by 86aae43f21. This creates an
infinite recursive call chain:
ice_init_hw()
ice_init_dev_hw()
ice_cfg_tx_topo() # topology change needed
ice_deinit_hw()
ice_init_hw() # reinit after CORER
ice_init_dev_hw() # recurse
ice_cfg_tx_topo()
... # stack overflow
Fix by moving ice_init_dev_hw() back out of ice_init_hw() and calling
it explicitly from ice_probe() and ice_devlink_reinit_up(). The third
caller, ice_cfg_tx_topo(), intentionally does not need ice_init_dev_hw()
during its reinit, it only needs the core HW reinitialization. This
breaks the recursion cleanly without adding flags or guards.
The deinit ordering changes from commit 8a37f9e2ff ("ice: move
ice_deinit_dev() to the end of deinit paths") which fixed slow rmmod
are preserved, only the init-side placement of ice_init_dev_hw() is
reverted.
Fixes: 8a37f9e2ff ("ice: move ice_deinit_dev() to the end of deinit paths")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Alexander Nowlin <alexander.nowlin@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-6-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ice_reset_all_vfs() ignores the return value of ice_vf_rebuild_vsi().
When the VSI rebuild fails (e.g. during NVM firmware update via
nvmupdate64e), ice_vsi_rebuild() tears down the VSI on its error path,
leaving txq_map and rxq_map as NULL. The subsequent unconditional call
to ice_vf_post_vsi_rebuild() leads to a NULL pointer dereference in
ice_ena_vf_q_mappings() when it accesses vsi->txq_map[0].
The single-VF reset path in ice_reset_vf() already handles this
correctly by checking the return value of ice_vf_reconfig_vsi() and
skipping ice_vf_post_vsi_rebuild() on failure.
Apply the same pattern to ice_reset_all_vfs(): check the return value
of ice_vf_rebuild_vsi() and skip ice_vf_post_vsi_rebuild() and
ice_eswitch_attach_vf() on failure. The VF is left safely disabled
(ICE_VF_STATE_INIT not set, VFGEN_RSTAT not set to VFACTIVE) and can
be recovered via a VFLR triggered by a PCI reset of the VF
(sysfs reset or driver rebind).
Note that this patch does not prevent the VF VSI rebuild from failing
during NVM update — the underlying cause is firmware being in a
transitional state while the EMP reset is processed, which can cause
Admin Queue commands (ice_add_vsi, ice_cfg_vsi_lan) to fail. This
patch only prevents the subsequent NULL pointer dereference that
crashes the kernel when the rebuild does fail.
crash> bt
PID: 50795 TASK: ff34c9ee708dc680 CPU: 1 COMMAND: "kworker/u512:5"
#0 [ff72159bcfe5bb50] machine_kexec at ffffffffaa8850ee
#1 [ff72159bcfe5bba8] __crash_kexec at ffffffffaaa15fba
#2 [ff72159bcfe5bc68] crash_kexec at ffffffffaaa16540
#3 [ff72159bcfe5bc70] oops_end at ffffffffaa837eda
#4 [ff72159bcfe5bc90] page_fault_oops at ffffffffaa893997
#5 [ff72159bcfe5bce8] exc_page_fault at ffffffffab528595
#6 [ff72159bcfe5bd10] asm_exc_page_fault at ffffffffab600bb2
[exception RIP: ice_ena_vf_q_mappings+0x79]
RIP: ffffffffc0a85b29 RSP: ff72159bcfe5bdc8 RFLAGS: 00010206
RAX: 00000000000f0000 RBX: ff34c9efc9c00000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000010 RDI: ff34c9efc9c00000
RBP: ff34c9efc27d4828 R8: 0000000000000093 R9: 0000000000000040
R10: ff34c9efc27d4828 R11: 0000000000000040 R12: 0000000000100000
R13: 0000000000000010 R14: R15:
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ff72159bcfe5bdf8] ice_sriov_post_vsi_rebuild at ffffffffc0a85e2e [ice]
#8 [ff72159bcfe5be08] ice_reset_all_vfs at ffffffffc0a920b4 [ice]
#9 [ff72159bcfe5be48] ice_service_task at ffffffffc0a31519 [ice]
#10 [ff72159bcfe5be88] process_one_work at ffffffffaa93dca4
#11 [ff72159bcfe5bec8] worker_thread at ffffffffaa93e9de
#12 [ff72159bcfe5bf18] kthread at ffffffffaa946663
#13 [ff72159bcfe5bf50] ret_from_fork at ffffffffaa8086b9
The panic occurs attempting to dereference the NULL pointer in RDX at
ice_sriov.c:294, which loads vsi->txq_map (offset 0x4b8 in ice_vsi).
The faulting VSI is an allocated slab object but not fully initialized
after a failed ice_vsi_rebuild():
crash> struct ice_vsi 0xff34c9efc27d4828
netdev = 0x0,
rx_rings = 0x0,
tx_rings = 0x0,
q_vectors = 0x0,
txq_map = 0x0,
rxq_map = 0x0,
alloc_txq = 0x10,
num_txq = 0x10,
alloc_rxq = 0x10,
num_rxq = 0x10,
The nvmupdate64e process was performing NVM firmware update:
crash> bt 0xff34c9edd1a30000
PID: 49858 TASK: ff34c9edd1a30000 CPU: 1 COMMAND: "nvmupdate64e"
#0 [ff72159bcd617618] __schedule at ffffffffab5333f8
#4 [ff72159bcd617750] ice_sq_send_cmd at ffffffffc0a35347 [ice]
#5 [ff72159bcd6177a8] ice_sq_send_cmd_retry at ffffffffc0a35b47 [ice]
#6 [ff72159bcd617810] ice_aq_send_cmd at ffffffffc0a38018 [ice]
#7 [ff72159bcd617848] ice_aq_read_nvm at ffffffffc0a40254 [ice]
#8 [ff72159bcd6178b8] ice_read_flat_nvm at ffffffffc0a4034c [ice]
#9 [ff72159bcd617918] ice_devlink_nvm_snapshot at ffffffffc0a6ffa5 [ice]
dmesg:
ice 0000:13:00.0: firmware recommends not updating fw.mgmt, as it
may result in a downgrade. continuing anyways
ice 0000:13:00.1: ice_init_nvm failed -5
ice 0000:13:00.1: Rebuild failed, unload and reload driver
Fixes: 12bb018c53 ("ice: Refactor VF reset")
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-5-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The V1 ADD_VLAN opcode had no success handler; filters sent via V1
stayed in ADDING state permanently. Add a fallthrough case so V1
filters also transition ADDING -> ACTIVE on PF confirmation.
Critically, add an `if (v_retval) break` guard: the error switch in
iavf_virtchnl_completion() does NOT return after handling errors,
it falls through to the success switch. Without this guard, a
PF-rejected ADD would incorrectly mark ADDING filters as ACTIVE,
creating a driver/HW mismatch where the driver believes the filter
is installed but the PF never accepted it.
For V2, this is harmless: iavf_vlan_add_reject() in the error
block already kfree'd all ADDING filters, so the success handler
finds nothing to transition.
Fixes: 968996c070 ("iavf: Fix VLAN_V2 addition/rejection")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-4-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The VLAN filter DELETE path was asymmetric with the ADD path: ADD
waits for PF confirmation (ADD -> ADDING -> ACTIVE), but DELETE
immediately frees the filter struct after sending the DEL message
without waiting for the PF response.
This is problematic because:
- If the PF rejects the DEL, the filter remains in HW but the driver
has already freed the tracking structure, losing sync.
- Race conditions between DEL pending and other operations
(add, reset) cannot be properly resolved if the filter struct
is already gone.
Add IAVF_VLAN_REMOVING state to make the DELETE path symmetric:
REMOVE -> REMOVING (send DEL) -> PF confirms -> kfree
-> PF rejects -> ACTIVE
In iavf_del_vlans(), transition filters from REMOVE to REMOVING
instead of immediately freeing them. The new DEL completion handler
in iavf_virtchnl_completion() frees filters on success or reverts
them to ACTIVE on error.
Update iavf_add_vlan() to handle the REMOVING state: if a DEL is
pending and the user re-adds the same VLAN, queue it for ADD so
it gets re-programmed after the PF processes the DEL.
The !VLAN_FILTERING_ALLOWED early-exit path still frees filters
directly since no PF message is sent in that case.
Also update iavf_del_vlan() to skip filters already in REMOVING
state: DEL has been sent to PF and the completion handler will
free the filter when PF confirms. Without this guard, the sequence
DEL(pending) -> user-del -> second DEL could cause the PF to return
an error for the second DEL (filter already gone), causing the
completion handler to incorrectly revert a deleted filter back to
ACTIVE.
Fixes: 968996c070 ("iavf: Fix VLAN_V2 addition/rejection")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-3-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When a VF goes down, the driver currently sends DEL_VLAN to the PF for
every VLAN filter (ACTIVE -> DISABLE -> send DEL -> INACTIVE), then
re-adds them all on UP (INACTIVE -> ADD -> send ADD -> ADDING ->
ACTIVE). This round-trip is unnecessary because:
1. The PF disables the VF's queues via VIRTCHNL_OP_DISABLE_QUEUES,
which already prevents all RX/TX traffic regardless of VLAN filter
state.
2. The VLAN filters remaining in PF HW while the VF is down is
harmless - packets matching those filters have nowhere to go with
queues disabled.
3. The DEL+ADD cycle during down/up creates race windows where the
VLAN filter list is incomplete. With spoofcheck enabled, the PF
enables TX VLAN filtering on the first non-zero VLAN add, blocking
traffic for any VLANs not yet re-added.
Remove the entire DISABLE/INACTIVE state machinery:
- Remove IAVF_VLAN_DISABLE and IAVF_VLAN_INACTIVE enum values
- Remove iavf_restore_filters() and its call from iavf_open()
- Remove VLAN filter handling from iavf_clear_mac_vlan_filters(),
rename it to iavf_clear_mac_filters()
- Remove DEL_VLAN_FILTER scheduling from iavf_down()
- Remove all DISABLE/INACTIVE handling from iavf_del_vlans()
VLAN filters now stay ACTIVE across down/up cycles. Only explicit
user removal (ndo_vlan_rx_kill_vid) or PF/VF reset triggers VLAN
filter deletion/re-addition.
Fixes: ed1f5b58ea ("i40evf: remove VLAN filters on close")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-2-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rename the IAVF_VLAN_IS_NEW state to IAVF_VLAN_ADDING to better
describe what the state represents: an ADD request has been sent to
the PF and is waiting for a response.
This is a pure rename with no behavioral change, preparing for a
cleanup of the VLAN filter state machine.
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260427-jk-iwl-net-petr-oros-fixes-v1-1-cdcb48303fd8@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
- Fix inverted check of registering the stats for branch tracing
When calling register_stat_tracer() which returns zero on success and
negative on error, the callers were checking the return of zero as an
error and printing a warning message. Because this was just a normal
printk() message and not a WARN(), it wasn't caught in any testing.
Fix the check to print the warning message when an error actually happens.
- Fix a typo in a comment in tracepoint.h
- Limit the size of event probes to 3K in size
It is possible to create a dynamic event probe via the tracefs system that
is greater than the max size of an event that the ring buffer can hold.
This basically causes the event to become useless. Limit the size of an
event probe to be 3K as that should be large enough to handle any dynamic
events being created, and fits within the PAGE_SIZE sub-buffers of the
ring buffer.
-----BEGIN PGP SIGNATURE-----
iIoEABYKADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCafJn9hQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6quUaAP9ezC2VXWugRIhOEmK0pIpY90zddsyv
xYTa3XuPP2r5JQEA8DcmH6fTo7JJxzbbyWPot/EgaqMt5XguqKC7txhjfww=
=+e7q
-----END PGP SIGNATURE-----
Merge tag 'trace-v7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix inverted check of registering the stats for branch tracing
When calling register_stat_tracer() which returns zero on success and
negative on error, the callers were checking the return of zero as an
error and printing a warning message. Because this was just a normal
printk() message and not a WARN(), it wasn't caught in any testing.
Fix the check to print the warning message when an error actually
happens.
- Fix a typo in a comment in tracepoint.h
- Limit the size of event probes to 3K in size
It is possible to create a dynamic event probe via the tracefs system
that is greater than the max size of an event that the ring buffer
can hold. This basically causes the event to become useless.
Limit the size of an event probe to be 3K as that should be large
enough to handle any dynamic events being created, and fits within
the PAGE_SIZE sub-buffers of the ring buffer.
* tag 'trace-v7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/probes: Limit size of event probe to 3K
tracepoint: Fix typo in tracepoint.h comment
tracing: branch: Fix inverted check on stat tracer registration
This driver provides a gpio chip, which is only possible when GPIOLIB
is enabled, which was previously guaranteed by the CONFIG_OF_GPIO
dependency that is now gone:
ERROR: modpost: "gpiochip_get_data" [drivers/regulator/rpi-panel-attiny-regulator.ko] undefined!
ERROR: modpost: "devm_gpiochip_add_data_with_key" [drivers/regulator/rpi-panel-attiny-regulator.ko] undefined!
Add an explicit GPIOLIB dependency instead.
Fixes: bf017304fc ("regulator: drop unneeded dependencies on OF_GPIO")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260429135812.112514-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When page_pool_create_percpu() fails on page_pool_list(), it falls
through to its err_uninit: label, which calls page_pool_uninit().
At that point page_pool_init() has already taken two references
when the user requested PP_FLAG_ALLOW_UNREADABLE_NETMEM:
pool->mp_ops->init(pool)
static_branch_inc(&page_pool_mem_providers);
Neither is undone by page_pool_uninit(); both are only undone by
__page_pool_destroy() (success-side teardown). The error path
therefore leaks the per-provider reference taken by mp_ops->init
(io_zcrx_ifq->refs in the io_uring zcrx provider, the dmabuf
binding refcount in the devmem provider) plus one increment of
the page_pool_mem_providers static branch on every failure of
xa_alloc_cyclic() inside page_pool_list().
The leaked io_zcrx_ifq->refs in turn pins everything
io_zcrx_ifq_free() would release on cleanup: ifq->user (uid),
ifq->mm_account (mmdrop), ifq->dev (device refcount),
ifq->netdev_tracker (netdev refcount), and the rbuf region.
The leaked static branch increment forces all subsequent
page_pool_alloc_netmems() and page_pool_return_page() callers to
take the slow mp_ops branch for the lifetime of the kernel.
Reachable via the io_uring zcrx path:
io_uring_register(IORING_REGISTER_ZCRX_IFQ) /* CAP_NET_ADMIN */
-> __io_uring_register
-> io_register_zcrx
-> zcrx_register_netdev
-> netif_mp_open_rxq
-> driver ndo_queue_mem_alloc
-> page_pool_create_percpu
-> page_pool_init succeeds (mp_ops->init runs, branch++)
-> page_pool_list fails (xa_alloc_cyclic -ENOMEM)
-> goto err_uninit <-- leak
The same shape applies to the devmem dmabuf provider via
mp_dmabuf_devmem_init()/mp_dmabuf_devmem_destroy().
Restore the cleanup symmetry by moving the mp_ops->destroy() and
static_branch_dec() calls out of __page_pool_destroy() and into
page_pool_uninit(), so page_pool_uninit() is again the strict
inverse of page_pool_init(). page_pool_uninit() has only two
callers (the err_uninit: path and __page_pool_destroy()), so this
preserves the single-call invariant on the success path while
fixing the err path. The error path of page_pool_init() itself
still skips the mp_ops cleanup correctly: mp_ops->init is the
last action that takes a reference before page_pool_init() returns
0, so when it returns an error neither the refcount nor the static
branch has been touched.
Triggering the bug requires xa_alloc_cyclic() to fail with -ENOMEM,
which under normal GFP_KERNEL retry behaviour is rare. It is
deterministic under CONFIG_FAULT_INJECTION with fail_page_alloc /
xa fault injection, or under sustained memory pressure. The leak
is silent: there is no warning, and the released kernel build
continues running with a permanently-incremented static branch.
Fixes: 0f92140468 ("memory-provider: dmabuf devmem memory provider")
Signed-off-by: Hasan Basbunar <basbunarhasan@gmail.com>
Link: https://patch.msgid.link/20260428170739.34881-1-basbunarhasan@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Always complete the airoha_dev_stop() routine regardless of the
airoha_set_vip_for_gdm_port() return value, since errors from
ndo_stop() are ignored by the networking stack and the interface is
always considered down after the call.
Fixes: 23020f0493 ("net: airoha: Introduce ethernet support for EN7581 SoC")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260428-airoha-ndo-stop-not-err-v1-1-674506d29a91@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VMBUS ring buffers must be page aligned. Therefore, the current value of
24K presents a challenge on ARM64 kernels (with 64K pages). So, use
VMBUS_RING_SIZE() to ensure they are always aligned and large enough to
hold all of the relevant data.
Cc: stable@vger.kernel.org
Fixes: 77ffe33363 ("hv_sock: use HV_HYP_PAGE_SIZE for Hyper-V communication")
Tested-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Hamza Mahfooz <hamzamahfooz@linux.microsoft.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://patch.msgid.link/20260428125339.13963-1-hamzamahfooz@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The IPv4/IPv6 and routing code is not very well separated from
the TCP/UDP code. Scope it down properly by providing a more
accurate file list, instead of net/ipv4/ and net/ipv6/
Now that the entry is more accurately representing layer 3
and routing merge in the nexthop entry into it.
Add Ido Schimmel as a co-maintainer, Ido's git history speaks
for itself.
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260428203924.1229169-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Minor clarifications in the README:
- call out what linters we expect to be clean
- make it clear that by "frameworks" we mean code under lib/
not just factoring code out in the same file
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit db359fccf2 ("mm: introduce a new page type for page pool in
page type") added a page_type field to struct net_iov at the same
offset as struct page::page_type, so that page_pool_set_pp_info() can
call __SetPageNetpp() uniformly on both pages and net_iovs.
The page-type API requires the field to hold the UINT_MAX "no type"
sentinel before a type can be set; for real struct page that invariant
is established by the page allocator on free. struct net_iov is not
allocated through the page allocator, so the field is left as zero
(io_uring zcrx, which uses __GFP_ZERO) or as slab garbage (devmem,
which uses kvmalloc_objs() without zeroing). When the page pool then
calls page_pool_set_pp_info() on a freshly-bound niov,
__SetPageNetpp()'s VM_BUG_ON_PAGE(page->page_type != UINT_MAX) fires
and the kernel BUGs. Triggered in selftests by io_uring zcrx setup
through the fbnic queue restart path:
kernel BUG at ./include/linux/page-flags.h:1062!
RIP: 0010:page_pool_set_pp_info (./include/linux/page-flags.h:1062
net/core/page_pool.c:716)
Call Trace:
<TASK>
net_mp_niov_set_page_pool (net/core/page_pool.c:1360)
io_pp_zc_alloc_netmems (io_uring/zcrx.c:1089 io_uring/zcrx.c:1110)
fbnic_fill_bdq (./include/net/page_pool/helpers.h:160
drivers/net/ethernet/meta/fbnic/fbnic_txrx.c:906)
__fbnic_nv_restart (drivers/net/ethernet/meta/fbnic/fbnic_txrx.c:2470
drivers/net/ethernet/meta/fbnic/fbnic_txrx.c:2874)
fbnic_queue_start (drivers/net/ethernet/meta/fbnic/fbnic_txrx.c:2903)
netdev_rx_queue_reconfig (net/core/netdev_rx_queue.c:137)
__netif_mp_open_rxq (net/core/netdev_rx_queue.c:234)
io_register_zcrx (io_uring/zcrx.c:818 io_uring/zcrx.c:903)
__io_uring_register (io_uring/register.c:931)
__do_sys_io_uring_register (io_uring/register.c:1029)
do_syscall_64 (arch/x86/entry/syscall_64.c:63
arch/x86/entry/syscall_64.c:94)
</TASK>
The same path is reachable through devmem dmabuf binding via
netdev_nl_bind_rx_doit() -> net_devmem_bind_dmabuf_to_queue().
Add a net_iov_init() helper that stamps ->owner, ->type and the
->page_type sentinel, and use it from both the devmem and io_uring
zcrx niov init loops.
Fixes: db359fccf2 ("mm: introduce a new page type for page pool in page type")
Acked-by: Vlastimil Babka (SUSE) <vbabka@kernel.org>
Acked-by: Byungchul Park <byungchul@sk.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://patch.msgid.link/20260428025320.853452-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Today we skip calling change_conf for negotiates and session setup
requests. This can be a problem for mchan as the immediate next call
after session setup could be due to an I/O that is made on the
mount point. For single channel, this is not a problem as
there will be several calls after setting up session.
This change enforces calling change_conf when the total credits contain
enough for reservations for echoes and oplocks. We expect this to happen
during the last session setup response. This way, echoes and oplocks are
not disabled before the first request to the server. So if that first
request is an open, it does not need to disable requesting leases.
Cc: <stable@vger.kernel.org>
Reviewed-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Currently, smb2_compound_op() allocates
struct smb2_compound_vars *vars using GFP_ATOMIC, although
smb2_compound_op() can sleep when it calls compound_send_recv()
before vars is freed.
Allocate vars using GFP_KERNEL.
Signed-off-by: Fredric Cover <fredric.cover.lkernel@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Clang warns (or errors with CONFIG_WERROR=y / W=e):
fs/ntfs/runlist.c:755:6: error: variable 'rl' is used uninitialized whenever 'if' condition is true [-Werror,-Wsometimes-uninitialized]
755 | if (overflows_type(lowest_vcn, vcn)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
...
fs/ntfs/runlist.c:971:9: note: uninitialized use occurs here
971 | kvfree(rl);
| ^~
...
rl has not been allocated at this point so the 'goto err_out' should
really just be a return of the error pointer -EIO.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
NTFS could store a filename as paired WIN32 and DOS $FILE_NAME attributes
for directories. But ntfs_delete() deleted both attributes for unlinking
a directory, but it also called drop_nlink() for each attributes.
This could trigger warnings when unlinking directories.
Signed-off-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
There currently isn't a max limit an event probe can be. One could make an
event greater than PAGE_SIZE, which makes the event useless because if
it's bigger than the max event that can be recorded into the ring buffer,
then it will never be recorded.
A event probe should never need to be greater than 3K, so make that the
max size. As long as the max is less than the max that can be recorded
onto the ring buffer, it should be fine.
Cc: stable@vger.kernel.org
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Fixes: 93ccae7a22 ("tracing/kprobes: Support basic types on dynamic events")
Link: https://patch.msgid.link/20260428122302.706610ba@gandalf.local.home
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add validation in xe_vm_bind_ioctl() to reject PAT indices
with XE_COH_NONE coherency mode when used with
DRM_XE_VM_BIND_FLAG_CPU_ADDR_MIRROR.
CPU address mirror mappings use system memory that is CPU
cached, which makes them incompatible with COH_NONE PAT
indices. Allowing COH_NONE with CPU cached buffers is a
security risk, as the GPU may bypass CPU caches and read
stale sensitive data from DRAM.
Although CPU_ADDR_MIRROR does not create an immediate
mapping, the backing system memory is still CPU cached.
Apply the same PAT coherency restrictions as
DRM_XE_VM_BIND_OP_MAP_USERPTR.
v2:
- Correct fix tag
v6:
- No change
v7:
- Correct fix tag
v8:
- Rebase
v9:
- Limit the restrictions to iGPU
v10:
- Just add the iGPU logic but keep dGPU logic
Fixes: b43e864af0 ("drm/xe/uapi: Add DRM_XE_VM_BIND_FLAG_CPU_ADDR_MIRROR")
Cc: <stable@vger.kernel.org> # v6.15+
Cc: Shuicheng Lin <shuicheng.lin@intel.com>
Cc: Mathew Alwin <alwin.mathew@intel.com>
Cc: Michal Mrozek <michal.mrozek@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Jia Yao <jia.yao@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Acked-by: Michal Mrozek <michal.mrozek@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patch.msgid.link/20260417055917.2027459-3-jia.yao@intel.com
(cherry picked from commit 4d58d7535e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Add validation in xe_vm_madvise_ioctl() to reject PAT indices with
XE_COH_NONE coherency mode when applied to CPU cached memory.
Using coh_none with CPU cached buffers is a security issue. When the
kernel clears pages before reallocation, the clear operation stays in
CPU cache (dirty). GPU with coh_none can bypass CPU caches and read
stale sensitive data directly from DRAM, potentially leaking data from
previously freed pages of other processes.
This aligns with the existing validation in vm_bind path
(xe_vm_bind_ioctl_validate_bo).
v2(Matthew brost)
- Add fixes
- Move one debug print to better place
v3(Matthew Auld)
- Should be drm/xe/uapi
- More Cc
v4(Shuicheng Lin)
- Fix kmem leak issues by the way
v5
- Remove kmem leak because it has been merged by another patch
v6
- Remove the fix which is not related to current fix
v7
- No change
v8
- Rebase
v9
- Limit the restrictions to iGPU
v10
- No change
Fixes: ada7486c56 ("drm/xe: Implement madvise ioctl for xe")
Cc: <stable@vger.kernel.org> # v6.18+
Cc: Shuicheng Lin <shuicheng.lin@intel.com>
Cc: Mathew Alwin <alwin.mathew@intel.com>
Cc: Michal Mrozek <michal.mrozek@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Jia Yao <jia.yao@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Acked-by: Michal Mrozek <michal.mrozek@intel.com>
Acked-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patch.msgid.link/20260417055917.2027459-2-jia.yao@intel.com
(cherry picked from commit 016ccdb674)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
When xe_gsc_read_out_header() fails, query_compatibility_version()
returns directly instead of jumping to the out_bo label. This skips
the xe_bo_unpin_map_no_vm() call, leaving the BO pinned and mapped
with no remaining reference to free it.
Fix by using goto out_bo so the error path properly cleans up the BO,
consistent with the other error handling in the same function.
Fixes: 0881cbe040 ("drm/xe/gsc: Query GSC compatibility version")
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patch.msgid.link/20260417163308.3416147-1-shuicheng.lin@intel.com
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
(cherry picked from commit 8de86d0a84)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In xe_eu_stall_stream_close(), drm_dev_put() is called before the
stream is disabled and its resources are freed. If this drops the
last reference, the device structures could be freed while the
subsequent cleanup code still accesses them, leading to a
use-after-free.
Fix this by moving drm_dev_put() after all device accesses are
complete. This matches the ordering in xe_oa_release().
Fixes: 9a0b11d4cf ("drm/xe/eustall: Add support to init, enable and disable EU stall sampling")
Cc: Harish Chegondi <harish.chegondi@intel.com>
Assisted-by: Claude:claude-opus-4.6
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Link: https://patch.msgid.link/20260415225428.3399934-1-shuicheng.lin@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit 35aff528f7)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Two error handling issues exist in xe_exec_queue_create_ioctl():
1. When xe_hw_engine_group_add_exec_queue() fails, the error path jumps
to put_exec_queue which skips xe_exec_queue_kill(). If the VM is in
preempt fence mode, xe_vm_add_compute_exec_queue() has already added
the queue to the VM's compute exec queue list. Skipping the kill
leaves the queue on that list, leading to a dangling pointer after
the queue is freed.
2. When xa_alloc() fails after xe_hw_engine_group_add_exec_queue() has
succeeded, the error path does not call
xe_hw_engine_group_del_exec_queue() to remove the queue from the hw
engine group list. The queue is then freed while still linked into
the hw engine group, causing a use-after-free.
Fix both by:
- Changing the xe_hw_engine_group_add_exec_queue() failure path to jump
to kill_exec_queue so that xe_exec_queue_kill() properly removes the
queue from the VM's compute list.
- Adding a del_hw_engine_group label before kill_exec_queue for the
xa_alloc() failure path, which removes the queue from the hw engine
group before proceeding with the rest of the cleanup.
Fixes: 7970cb3696 ("'drm/xe/hw_engine_group: Register hw engine group's exec queues")
Cc: Francois Dugast <francois.dugast@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Assisted-by: Claude:claude-opus-4.6
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260408020647.3397933-1-shuicheng.lin@intel.com
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
(cherry picked from commit 37c831f401)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
When xe_dma_buf_init_obj() fails, the attachment from
dma_buf_dynamic_attach() is not detached. Add dma_buf_detach() before
returning the error. Note: we cannot use goto out_err here because
xe_dma_buf_init_obj() already frees bo on failure, and out_err would
double-free it.
Fixes: dd08ebf6c3 ("drm/xe: Introduce a new DRM driver for Intel GPUs")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4.6
Reviewed-by: Mattheq Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260408175255.3402838-5-shuicheng.lin@intel.com
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
(cherry picked from commit a828eb185a)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
When drm_gpuvm_resv_object_alloc() fails, the pre-allocated storage bo
is not freed. Add xe_bo_free(storage) before returning the error.
xe_dma_buf_init_obj() calls xe_bo_init_locked(), which frees the bo on
error. Therefore, xe_dma_buf_init_obj() must also free the bo on its own
error paths. Otherwise, since xe_gem_prime_import() cannot distinguish
whether the failure originated from xe_dma_buf_init_obj() or from
xe_bo_init_locked(), it cannot safely decide whether the bo should be
freed.
Add comments documenting the ownership semantics: on success, ownership
of storage is transferred to the returned drm_gem_object; on failure,
storage is freed before returning.
v2: Add comments to explain the free logic.
Fixes: eb289a5f6c ("drm/xe: Convert xe_dma_buf.c for exhaustive eviction")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4.6
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260408175255.3402838-4-shuicheng.lin@intel.com
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
(cherry picked from commit 78a6c5f899)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
When XE_BO_FLAG_GGTT_ALL is set without XE_BO_FLAG_GGTT, the function
returns an error without freeing a caller-provided bo, violating the
documented contract that bo is freed on failure.
Add xe_bo_free(bo) before returning the error.
Fixes: 5a3b0df25d ("drm/xe: Allow bo mapping on multiple ggtts")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4.6
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260408175255.3402838-3-shuicheng.lin@intel.com
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
(cherry picked from commit 3fbd6cf43c)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
When type is ttm_bo_type_device and aligned_size != size, the function
returns an error without freeing a caller-provided bo, violating the
documented contract that bo is freed on failure.
Add xe_bo_free(bo) before returning the error.
Fixes: 4e03b58414 ("drm/xe/uapi: Reject bo creation of unaligned size")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4.6
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260408175255.3402838-2-shuicheng.lin@intel.com
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
(cherry picked from commit 601c2aa087)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
xe_exec_queue_tlb_inval_last_fence_put_unlocked() uses q->vm->xe as the
first argument to xe_assert(). This function is called unconditionally
from xe_exec_queue_destroy() for all queues, including kernel queues
that have q->vm == NULL (e.g., queues created during GT init in
xe_gt_record_default_lrcs() with vm=NULL).
While current compilers optimize away the q->vm->xe dereference (even
in CONFIG_DRM_XE_DEBUG=y builds, the compiler pushes the dereference
into the WARN branch that is only taken when the assert condition is
false), the code is semantically incorrect and constitutes undefined
behavior in the C abstract machine for the NULL pointer case.
Use gt_to_xe(q->gt) instead, which is always valid for any exec queue.
This is consistent with how xe_exec_queue_destroy() itself obtains the
xe_device pointer in its own xe_assert at the top of the function.
Fixes: b2d7ec41f2 ("drm/xe: Attach last fence to TLB invalidation job queues")
Assisted-by: Claude:claude-opus-4.6
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260409003449.3405767-1-shuicheng.lin@intel.com
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
(cherry picked from commit 96078a1c68)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The suballocator algorithm tracks a hole cursor at the last allocation
and tries to allocate after it. This is optimized for fence-ordered
progress, where older allocations are expected to become reusable first.
In fence-enabled mode, that ordering assumption holds. In fence-disabled
mode, allocations may be freed in arbitrary order, so limiting allocation
to the current hole window can miss valid free space and fail allocations
despite sufficient total space.
Use DRM memory manager instead of sub-allocator to get rid of this issue
as CCS read/write operations do not use fences.
Fixes: 864690cf4d ("drm/xe/vf: Attach and detach CCS copy commands with BO")
Signed-off-by: Satyanarayana K V P <satyanarayana.k.v.p@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Maarten Lankhorst <dev@lankhorst.se>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260408110145.1639937-6-satyanarayana.k.v.p@intel.com
(cherry picked from commit 6c84b49301)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Add a memory pool to allocate sub-ranges from a BO-backed pool
using drm_mm.
Signed-off-by: Satyanarayana K V P <satyanarayana.k.v.p@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Maarten Lankhorst <dev@lankhorst.se>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20260408110145.1639937-5-satyanarayana.k.v.p@intel.com
(cherry picked from commit 1ce3229f8f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The register-save-restore debugfs prints whitelist entries as offset
ranges. E.g.,
REG[0x39319c-0x39319f]: allow read access
for a single dword-sized register. However the GENMASK value used to
set the lower bits to '1' for the upper bound of the whitelist range
incorrectly included one more bit than it should have, causing the
whitelist ranges to sometimes appear twice as large as they really were.
For example,
REG[0x6210-0x6217]: allow rw access
was also intended to be a single dword-sized register whitelist (with a
range 0x6210-0x6213) but was printed incorrectly as a qword-sized range
because one too many bits was flipped on. Similar 'off by one' logic
was applied when printing 4-dword register ranges and 64-dword register
ranges as well.
Correct the GENMASK logic to print these ranges in debugfs correctly.
No impact outside of correcting the misleading debugfs output.
Fixes: d855d2246e ("drm/xe: Print whitelist while applying")
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Link: https://patch.msgid.link/20260408-regsr_wl_range-v1-1-e9a28c8b4264@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit 1a2a722ff9)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
ROW_CHICKEN5 is a masked register (i.e., to adjust the value of any of
the lower 16 bits, the corresponding bit in the upper 16 bits must also
be set). Add the XE_REG_OPTION_MASKED to its definition; failure to do
so will cause workaround updates of this register to not apply properly.
Bspec: 56853
Fixes: 835cd6cbb0 ("drm/xe/xe3p_lpg: Add initial workarounds for graphics version 35.10")
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patch.msgid.link/20260410-xe3p_tuning-v1-3-e206a62ee38f@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit cd84bfbba7)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
From Xe2 onward (i.e., all platforms officially supported by the Xe
driver), the GAMSTLB_CTRL register is located at offset 0x477C and
represented by the macro "GAMSTLB_CTRL" in code. However the register
formerly resided at offset 0xCF4C on Xe1-era platforms, and we also have
macro XEHP_GAMSTLB_CTRL that represents this old offset in the
unofficial/developer-only Xe1 code. When tuning for the register was
added for Xe3p_LPG, the old Xe1-era macro was accidentally used instead
of the proper macro for Xe2 and beyond, causing the tuning to not be
applied properly. Use the proper definition so that the correct offset
is written to.
Bspec: 59298
Fixes: 377c89bfaa ("drm/xe/xe3p_lpg: Set STLB bank hash mode to 4KB")
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patch.msgid.link/20260410-xe3p_tuning-v1-2-e206a62ee38f@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit 0b1676eafd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Even though commit 8fcb7dfb8b ("drm/xe/xe3p_lpg: Add support for
graphics IP 35.10") mentions that the support for Indirect Ring State
exists for Xe3p_LPG, it missed actually setting the feature flag in
graphics_xe3p_lpg. Fix that by adding the missing member.
Fixes: 8fcb7dfb8b ("drm/xe/xe3p_lpg: Add support for graphics IP 35.10")
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patch.msgid.link/20260401-xe3p_lpg-indirect-ring-state-v1-1-0e4b5edf6898@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
(cherry picked from commit ec4f4970eb)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
There appears to have been a silent merge conflict between some commits
updating the workaround tables on Xe's -fixes and -next branches:
- Commit bc6387a2e0 ("drm/xe/xe2_hpg: Fix handling of Wa_14019988906
& Wa_14019877138") from the fixes branch moved the Xe2_HPG instance
of two workarounds touching the PSS_CHICKEN register from the
engine_was[] table to the lrc_was[] table; the equivalent
implementation for all other platforms/IPs were already properly
located on lrc_was[]. This commit on the fixes branch is a
cherry-pick of commit e04c609eed ("drm/xe/xe2_hpg: Fix handling of
Wa_14019988906 & Wa_14019877138") that already existed on the next
branch.
- Commit 55b19abb6c ("drm/xe: Consolidate workaround entries for
Wa_14019877138") and commit c2142a1a84 ("drm/xe: Consolidate
workaround entries for Wa_14019988906") consolidated the individual
entries per IP generation for each workaround into single, larger
range-based entries.
During merge conflict resolution the Xe2_HPG-specific entries (i.e.,
those with rule "GRAPHICS_VERSION_RANGE(2001, 2002)") were accidentally
resurrected, even though the table already contains the consolidated
entries that match a superset of thse ranges. These redundant entries
don't cause any build failures but do trigger a dmesg error during probe
on BMG-G21 devices:
xe 0000:03:00.0: [drm] *ERROR* Tile0: GT0: discarding save-restore reg 7044 (clear: 00000400, set: 00000400, masked: yes, mcr: yes): ret=-22
xe 0000:03:00.0: [drm] *ERROR* Tile0: GT0: discarding save-restore reg 7044 (clear: 00000020, set: 00000020, masked: yes, mcr: yes): ret=-22
Re-drop the Xe2_HPG-specific table entries to eliminate the error.
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/work_items/7433
Fixes: 17b95278ae ("Merge tag 'drm-xe-next-2026-03-02' of https://gitlab.freedesktop.org/drm/xe/kernel into drm-next")
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Shuicheng Lin <shuicheng.lin@intel.com>
Link: https://patch.msgid.link/20260401-wa_merge_conflict-v1-1-b477ab53fedc@intel.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
(cherry picked from commit c79bc99944)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Add missing pad and extensions check to xe_vm_get_property_ioctl
v2:
- Combine with other check (Auld)
Fixes: 50c577eab0 ("drm/xe/xe_vm: Implement xe_vm_get_property_ioctl")
Suggested-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patch.msgid.link/20260331181216.37775-2-jonathan.cavitt@intel.com
(cherry picked from commit 896070686b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
xe_guc_submit_wedge() runs in the DMA-fence signaling path, where
GFP_KERNEL memory allocations are not permitted. However, registering
guc_submit_wedged_fini via drmm_add_action_or_reset() triggers such an
allocation.
Avoid this by moving the logic from guc_submit_wedged_fini() into
guc_submit_fini(), where wedged exec queue references are dropped during
normal teardown.
Fixes: 8ed9aaae39 ("drm/xe: Force wedged state and block GT reset upon any GPU hang")
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patch.msgid.link/20260326210116.202585-3-matthew.brost@intel.com
(cherry picked from commit 4a706bd93c)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
stop_sessions() walks conn_list with hash_for_each() and, for every
entry, drops conn_list_lock across the transport ->shutdown() call
before re-acquiring the read lock to continue the loop. The hash
walk relies on cross-iteration state (the current bucket and the
hlist position), which is not preserved across unlock/relock: if
another thread performs a list mutation during the unlocked window,
the ongoing iteration becomes unreliable and can re-visit
connections that have already been handled or skip connections that
have not. The outer `if (!hash_empty(conn_list)) goto again;` retry
masks the symptom in the common case but does not address the
unsafe iteration itself.
Reframe the loop so it never relies on iterator state across
unlock/relock. Under conn_list_lock held for read, pick the first
connection whose ->shutdown() has not yet been issued by this path,
pin it by taking an extra reference, record that fact on the
connection and mark it EXITING while still inside the locked walk,
then drop the lock. Then call ->shutdown() outside the lock, drop
the pin (freeing the connection if the handler already released its
reference), and restart from the top.
Use a new per-connection flag, conn->stop_called, as the "shutdown
issued from stop_sessions()" marker rather than reusing the status
state. ksmbd_conn_set_exiting() is also invoked by
ksmbd_sessions_deregister() on sibling channels of a multichannel
session without issuing a transport shutdown, so treating
KSMBD_SESS_EXITING as "already handled here" would skip connections
that still need shutdown() to wake their handler out of recv(),
leaving the outer retry waiting indefinitely for the hash to drain.
stop_sessions() is serialised by init_lock in
ksmbd_conn_transport_destroy(), so writing stop_called under the
read lock has no other writer.
Set EXITING inside the locked walk so the selection, the stop_called
marker, and the status transition all happen together, and guard
against regressing a connection that has already advanced to
KSMBD_SESS_RELEASING on its own (for example, if the handler exited
its receive loop for an unrelated reason between teardown steps).
When the pin drop is the last put, release the transport and pair
ida_destroy(&target->async_ida) with the ida_init() done in
ksmbd_conn_alloc(), so stop_sessions() retiring a connection on its
own does not leak the xarray backing of the embedded async_ida.
The outer retry with msleep() is kept to wait for handler threads to
reach ksmbd_conn_free() and drain the hash.
Observed with an instrumented build that logs one line per visit and
widens the unlocked window before ->shutdown() by 200 ms, under
five concurrent cifs mounts (nosharesock, one connection each):
* Current code: the same connection address is revisited many
times during a single stop_sessions() call and ->shutdown() is
invoked well beyond the number of live connections before the
hash finally drains.
* Rewritten code: each live connection produces exactly one
->shutdown() call; the function returns as soon as the hash is
empty.
Functional teardown via `ksmbd.control --shutdown` with the same
five mounts completes cleanly on the rewritten path.
Performance is observably unchanged. Tearing down N concurrent
nosharesock cifs connections with `ksmbd.control --shutdown` +
`rmmod ksmbd` takes essentially the same wall time before and after
the rewrite:
N before after
10 4.93s 5.34s
30 7.34s 7.03s
50 7.31s 7.01s (3-run avg: 7.04s vs 7.25s)
100 6.98s 6.78s
200 6.77s 6.89s
and the number of ->shutdown() calls equals the number of live
connections on both paths when the race is not widened. The
teardown is dominated by the msleep(100)-based outer retry waiting
for handler threads to run ksmbd_conn_free(), not by the iteration
itself; the restartable loop's worst-case O(N^2) visit cost is in
the microseconds even at N=200 and sits far below the msleep(100)
granularity.
Applied alone on top of ksmbd-for-next-next, this patch does not
introduce a new leak site. Under the same reproducer (10x
concurrent-holders + ss -K + ksmbd.control --shutdown + rmmod), the
tree still shows the pre-existing per-connection transport leak
count that arises when the last refcount drop lands in one of
ksmbd_conn_r_count_dec(), __free_opinfo() or session_fd_check() -
all of which end with a bare kfree() today. kmemleak backtraces
for the unreferenced objects point into the TCP accept path
(sk_clone -> inet_csk_clone_lock, sock_alloc_inode) and none
involve stop_sessions(). Plugging those bare-kfree sites is the
responsibility of the follow-up patch.
Fixes: e2f34481b2 ("cifsd: add server-side procedures for SMB3")
Cc: stable@vger.kernel.org
Signed-off-by: DaeMyung Kang <charsyam@gmail.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
early exit in smb2_populate_readdir_entry() if the requested info_level
is unknown.
Signed-off-by: Marios Makassikis <mmakassikis@freebox.fr>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
When an embedded panel has no DDC, read the EDID from
the VBIOS embedded panel info and use that.
Fixes: 7c7f5b15be ("drm/amd/display: Refactor edid read.")
Link: https://gitlab.freedesktop.org/drm/amd/-/work_items/5192
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 399b9abc35)
Some board manufacturers hardcode the EDID for the embedded
panel in the VBIOS. This EDID should be used when the panel
doesn't have a DDC.
For reference, see the legacy non-DC display code:
amdgpu_atombios_encoder_get_lcd_info()
This is necessary to support embedded connectors without DDC.
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Link: https://gitlab.freedesktop.org/drm/amd/-/work_items/5192
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit eb105e63b4)
When the DDC channel ID is set to CHANNEL_ID_UNKNOWN,
pass NULL to the AUX regs array.
This is necessary to support embedded connectors without DDC.
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Link: https://gitlab.freedesktop.org/drm/amd/-/work_items/5192
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 155baf3038)
When the DDC channel ID is set to CHANNEL_ID_UNKNOWN,
pass NULL to the AUX regs array.
This is necessary to support embedded connectors without DDC.
Fixes: 7c15fd86aa ("drm/amd/display: dc/dce: add initial DCE6 support (v10)")
Link: https://gitlab.freedesktop.org/drm/amd/-/work_items/5192
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 38a70e50b2)
