virtblk_report_zones() trusts the device-reported number of zones when
walking the report buffer:
nz = min_t(u64, virtio64_to_cpu(vblk->vdev, report->nr_zones),
nr_zones);
...
for (i = 0; i < nz && zone_idx < nr_zones; i++) {
ret = virtblk_parse_zone(vblk, &report->zones[i], ...);
The buffer is allocated by virtblk_alloc_report_buffer(), whose size is
capped by the queue's max hardware sectors and max segments and can
therefore hold fewer descriptors than nr_zones. nz is bounded only by
the device-supplied report->nr_zones and the requested nr_zones, never
by the buffer's descriptor capacity. At probe time the request count is
unbounded (blk_revalidate_disk_zones() calls report_zones() with
nr_zones == UINT_MAX), so the device-supplied report->nr_zones is the
sole gate: a device that reports more zones than fit in the buffer
drives the loop to read report->zones[i] past the end of the allocation.
A malicious or buggy virtio-blk device that reports an inflated nr_zones
triggers this during zone revalidation at probe. KASAN reports a
vmalloc-out-of-bounds read in virtblk_report_zones() against the report
buffer allocated a few lines earlier.
Clamp nz to the number of descriptors that actually fit in the report
buffer.
Fixes: 95bfec41bd ("virtio-blk: add support for zoned block devices")
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Link: https://patch.msgid.link/20260607124834.3059944-1-michael.bommarito@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The LTC4283 device has up to 8 pins that can be configured as GPIOs.
Note that PGIO pins are not set as GPIOs by default so if they are
configured to be used as GPIOs we need to make sure to initialize them
to a sane default. They are set as inputs by default.
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20260502-ltc4283-support-v13-3-1c206542e652@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Support the LTC4283 Hot Swap Controller. The device features programmable
current limit with foldback and independently adjustable inrush current to
optimize the MOSFET safe operating area (SOA). The SOA timer limits MOSFET
temperature rise for reliable protection against overstresses.
An I2C interface and onboard ADC allow monitoring of board current,
voltage, power, energy, and fault status.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20260502-ltc4283-support-v13-2-1c206542e652@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some workloads with different CPU capacities consume more power with
timer migration than before. The recently introduced per capacity
hierarchies were supposed to alleviate this problem. However it appears
to also regress other types of workloads, especially when plenty of
capacities live together in the same machine.
Disable the feature until a reasonable solution is found.
Fixes: 098cbaad8e ("timers/migration: Split per-capacity hierarchies")
Reported-by: Christian Loehle <christian.loehle@arm.com>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260609123356.28449-1-frederic@kernel.org
Closes: https://lore.kernel.org/all/3b79338f-6cfc-4722-8062-9103db2c8ad1@arm.com
address post-7.1 issues or aren't considered suitable for backporting.
Thre's a 2 patch series "mm/damon/{reclaim,lru_sort}: handle ctx
allocation failures" from SeongJae Park which fixes a couple of DAMON
-ENOMEM bloopers. The rest are singletons - please see the individual
changelogs for details.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCaieN5AAKCRDdBJ7gKXxA
jkN7AP9wXhRFOUq0EPeQxnlie7vgM/jiDuOoPAn7EUt9S7pqCwEApJnxEbMzXioD
Jx6MxoUqqa/d5wXb7u0MRgT76n9KOwk=
=hdKc
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2026-06-08-20-51' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"11 hotfixes. 9 are for MM. 8 are cc:stable and the remaining 3 address
post-7.1 issues or aren't considered suitable for backporting.
Thre's a two-patch series "mm/damon/{reclaim,lru_sort}: handle ctx
allocation failures" from SeongJae Park which fixes a couple of DAMON
-ENOMEM bloopers. The rest are singletons - please see the individual
changelogs for details"
* tag 'mm-hotfixes-stable-2026-06-08-20-51' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/mincore: handle non-swap entries before !CONFIG_SWAP guard
arm64: mm: call pagetable dtor when freeing hot-removed page tables
mm/list_lru: drain before clearing xarray entry on reparent
mm/huge_memory: use correct flags for device private PMD entry
mm/damon/lru_sort: handle ctx allocation failure
mm/damon/reclaim: handle ctx allocation failure
zram: fix use-after-free in zram_bvec_write_partial()
MAINTAINERS: update Baoquan He's email address
tools headers UAPI: sync linux/taskstats.h for procacct.c
mm/cma_sysfs: skip inactive CMA areas in sysfs
ipc/shm: serialize orphan cleanup with shm_nattch updates
The LTC4283 is a negative voltage hot swap controller that drives an
external N-channel MOSFET to allow a board to be safely inserted and
removed from a live backplane.
Special note for the "adi,vpower-drns-enable" property. It allows to choose
between the attenuated MOSFET drain voltage or the attenuated input
voltage at the RTNS pin (effectively choosing between input or output
power). This is a system level decision not really intended to change at
runtime and hence is being added as a Firmware property.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20260502-ltc4283-support-v13-1-1c206542e652@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adds support for the Infineon XDP730 Digital eFuse Controller by
updating the existing XDP720 driver.
Signed-off-by: Ashish Yadav <ashish.yadav@infineon.com>
Link: https://lore.kernel.org/r/20260609072231.15486-3-Ashish.Yadav@infineon.com
[groeck: Fixed conflicts in xdp720_id declaration]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add documentation for the device tree binding of the XDP730 eFuse.
Rename node to efuse to accurately reflect its hardware function.
Signed-off-by: Ashish Yadav <ashish.yadav@infineon.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20260609072231.15486-2-Ashish.Yadav@infineon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a PMBus driver for the Analog Devices MAX20860A step-down DC-DC
switching regulator. The MAX20860A provides monitoring of input/output
voltage, output current, and temperature via the PMBus interface using
linear data format. Optional regulator support is available via
CONFIG_SENSORS_MAX20860A_REGULATOR.
Signed-off-by: Syed Arif <arif.syed@hpe.com>
Signed-off-by: Sanman Pradhan <psanman@juniper.net>
Link: https://lore.kernel.org/r/20260601184516.919488-3-sanman.pradhan@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for BMR316, BMR321, BMR350 and BMR351 DC/DC converter
modules from Flex to the pmbus driver.
Signed-off-by: Daniel Nilsson <linux@erq.se>
Link: https://lore.kernel.org/r/20260603085712.659432-2-linux@erq.se
[groeck: Resolved conflicts (explicit struct members in pmbus_id)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Named initializers are better readable and more robust to changes of the
struct definition. This robustness is relevant for a planned change to
struct platform_device_id replacing .driver_data by an anonymous unit.
While touching these arrays unify usage of commas.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/25d38df8db42d69f33fa30267c9fd5ea058223d0.1779894738.git.u.kleine-koenig@baylibre.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver explicitly set the .driver_data member of struct
platform_device_id to zero without relying on that value. Drop this
unused assignments.
While touching this array unify spacing and use named initializers for
.name.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Acked-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/972c9998054c7944f63266819d6fb08b36edb5c5.1779894738.git.u.kleine-koenig@baylibre.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
set_fan() parses user input with kstrtol() and passes the resulting
value to FAN16_TO_REG() on chips with 16-bit fan support.
Negative fan speeds are not meaningful and should be rejected before
conversion. Worst scenario, one may be able to abuse undefined
behaviour of signed overflow to possibly induce rpm * 2 == 0 in
FAN16_TO_REG(), thus causing a division by zero.
Instead, clamp val < 0 to zero and keep the conversion in its valid
input domain, avoiding unsafe arithmetic in the register conversion
path.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 17d648bf57 ("it87: Add support for the IT8716F")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20260529141839.1639287-1-n.zhandarovich@fintech.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the ASRock Z890 Pro-A customer ID to the list of supported
boards for the NCT6683 hardware monitoring driver.
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit
Signed-off-by: Reiner Pröls <reiner.proels@gmail.com>
Link: https://lore.kernel.org/r/20260521212632.223724-1-Reiner.Proels@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since device_property_read_string() and similar functions defined in
linux/property.h are used in the driver add explicit include for
linux/mod_devicetable.h and linux/property.h rather than having implicit
inclusions.
Removed of_match_ptr() improving non-Device Tree compatibility of the
driver and drop unnecessary __maybe_unused.
Header linux/of.h can't be removed yet since macro is_of_node() is used.
Signed-off-by: Flaviu Nistor <flaviu.nistor@gmail.com>
Link: https://lore.kernel.org/r/20260522052352.12139-1-flaviu.nistor@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver caches the PWM frequency register and the CONFIG_FAN slow-clock
select bit, but never lets userspace pick a different output frequency.
Add a pwm1_freq sysfs attribute that selects the closest SCS + PFR
combination for the requested value in Hz, gated by manual mode like
set_pwm1(). PFR is clamped to 31 so that 2*PFR fits in the chip's 6-bit
PWM register (matching the existing scaling assumption in show_pwm1).
The hardware LUT hysteresis register is shared by all LUT entries, so
the per-point pwm1_auto_pointN_temp_hyst attributes can't be made RW
without N-to-1 cross-attribute side effects. Following the max31760
precedent, expose a single chip-wide pwm1_auto_point_temp_hyst attribute
holding the hysteresis amount in millidegrees; the per-point attributes
stay RO and continue to show the resulting absolute trip-down
temperature for each entry.
This was tested on a Linksys LGS328MPC switch hardware where the fan
would not spin with the default PWM Frequency, which is why this change
is required.
Signed-off-by: Jan-Henrik Bruhn <kernel@jhbruhn.de>
Link: https://lore.kernel.org/r/20260523133617.3439102-1-kernel@jhbruhn.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver seeds the chip's SET_RTC register once at probe with
ktime_get_real_seconds(). Over a long uptime the chip's internal
seconds counter drifts away from the host's wall-clock time, so the
timestamp embedded in each blackbox record stops being meaningful
in wall-clock terms. The datasheet recommends that the host
periodically resynchronise the counter to address this; today the
driver has no userspace-facing knob for that.
Expose SET_RTC via an rtc debugfs file alongside the other adm1266
debugfs entries:
read -- returns the chip's current SET_RTC seconds counter, so
userspace can observe how far the chip has drifted from
host wall-clock without writing anything.
write -- the kernel re-reads ktime_get_real_seconds() itself and
pushes it to the chip. The write payload is ignored;
userspace does not get to supply its own timestamp
value, so there is no way for it to push a wrong time
into the chip.
A small userspace agent (chrony hook, systemd-timesyncd dispatch
script, or a periodic cron job) can write to this file to keep the
chip's counter aligned with wall-clock across long uptimes.
Both the read and write paths take pmbus_lock to serialise against
the pmbus_core's own PAGE+register sequences and against the other
adm1266 debugfs accessors that already run under the same lock.
While at it, drop the now-redundant adm1266_set_rtc() probe-time
helper. The new adm1266_rtc_set() callback does exactly the same
byte-packing and write; probe just calls adm1266_rtc_set(client, 0)
(the ignored @val argument) after pmbus_do_probe() so the
pmbus_lock acquired by the new helper has a live mutex to take.
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Assisted-by: Claude-Code:claude-opus-4-7
Assisted-by: sashiko:gemini-3.1-pro-preview
Link: https://lore.kernel.org/r/20260520-adm1266-v5-3-c72ef1fac1ea@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADM1266 maintains a 16-bit non-volatile POWERUP_COUNTER register
(0xE4, datasheet Rev. D, Table 93) that increments on every power
cycle and cannot be reset by the host. Each blackbox record already
embeds the counter at record time, so the standalone live value is
primarily useful for matching a captured record back to the boot it
came from when correlating logs.
Expose it as a read-only debugfs file alongside sequencer_state. The
block-read returns two payload bytes in little-endian order.
Take pmbus_lock around the block-read so the access serialises with
any pmbus_core sequence that sets PAGE on the device. Without it, a
PAGE write from another thread could interleave between a PAGE set
and a paged read elsewhere in the driver and corrupt either side's
view of the device state machine.
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Assisted-by: Claude-Code:claude-opus-4-7
Assisted-by: sashiko:gemini-3.1-pro-preview
Link: https://lore.kernel.org/r/20260520-adm1266-v5-2-c72ef1fac1ea@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADM1266 blackbox can be configured in two recording modes via
BLACKBOX_CONFIG[0]: cyclic, where the device overwrites the oldest
record once the 32-record buffer fills, and single, where it stops
recording until the buffer is cleared. Deployments that need to
preserve the full record history across multiple fault episodes
typically run in single mode and need a way to clear the buffer
after the records have been collected.
Expose a write-only debugfs file alongside sequencer_state. Writing
any data to it issues the documented clear-blackbox sub-command:
a 2-byte block-write to READ_BLACKBOX (0xDE) with payload
{0xFE, 0x00} (datasheet Rev. D).
The clear is taken under pmbus_lock because READ_BLACKBOX is also
used by adm1266_nvmem_read_blackbox() to walk records one at a
time; both paths run under pmbus_lock so the clear cannot
interleave mid-iteration and corrupt the read sequence.
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Assisted-by: Claude-Code:claude-opus-4-7
Assisted-by: sashiko:gemini-3.1-pro-preview
Link: https://lore.kernel.org/r/20260520-adm1266-v5-1-c72ef1fac1ea@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The delayed polling work rearms itself from the work function, so use
explicit delayed-work setup and cleanup instead of
devm_delayed_work_autocancel().
Initialize the delayed work with INIT_DELAYED_WORK() and register a
devres cleanup action that calls disable_delayed_work_sync() during
teardown.
This addresses the concern raised during review about the polling work
being able to requeue itself while the driver is being removed.
Signed-off-by: Shubham Chakraborty <chakrabortyshubham66@gmail.com>
Link: https://lore.kernel.org/r/20260517080445.103962-4-chakrabortyshubham66@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend the raspberrypi-hwmon driver to expose firmware-provided
voltage measurements through the hwmon subsystem.
The driver now exports the following voltage inputs:
- in0_input (core)
- in1_input (sdram_c)
- in2_input (sdram_i)
- in3_input (sdram_p)
Voltage values returned by firmware are converted from microvolts
to millivolts as expected by the hwmon subsystem.
Update the documentation related to it.
The existing undervoltage sticky alarm handling is preserved and
associated with the first voltage channel.
Tested in -
- Raspberry Pi 3b+ (Linux raspberrypi 6.12.75+rpt-rpi-v8 #1 SMP PREEMPT
Debian 1:6.12.75-1+rpt1 (2026-03-11) aarch64 GNU/Linux)
Signed-off-by: Shubham Chakraborty <chakrabortyshubham66@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20260517080445.103962-3-chakrabortyshubham66@gmail.com
[groeck: Added missing empty line after declaration]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add Raspberry Pi firmware voltage domain identifiers for the mailbox
property interface.
Also add the voltage request structure used with
RPI_FIRMWARE_GET_VOLTAGE so firmware clients can share the common API
definition from the firmware header.
Signed-off-by: Shubham Chakraborty <chakrabortyshubham66@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20260517080445.103962-2-chakrabortyshubham66@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since device_property_read_string() is used in the probe function add
explicit include for linux/mod_devicetable.h and linux/property.h rather
than having implicit inclusions. Header linux/of.h can be removed and
also of_match_ptr() improving non-Device Tree compatibility of the driver.
Remove __maybe_unuse because it is not needed anymore.
Signed-off-by: Flaviu Nistor <flaviu.nistor@gmail.com>
Link: https://lore.kernel.org/r/20260518072337.4918-1-flaviu.nistor@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use scoped_guard() instead of hwmon_lock() / hwmon_unlock() to acquire
and release the hardware monitoring subsystem lock.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use scoped_guard() instead of hwmon_lock() / hwmon_unlock() to acquire
and release the hardware monitoring subsystem lock.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use guard() and scoped_guard() instead of hwmon_lock() / hwmon_unlock()
to acquire and release the hardware monitoring subsystem lock.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
- Remove broken Intel wiki link; add Intel SDM download page link
- Fix description of tempX_max to clarify it is not Core2-only
- Correct tempX_label string for package temperature (changed in commit
2bc0e6d07e ("hwmon: (coretemp) rearrange tjmax handing code"))
Signed-off-by: Roman Bakshansky <bakshansky.lists@gmail.com>
Link: https://lore.kernel.org/r/20260517152027.350356-1-bakshansky.lists@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Document the debugfs serial_number file exposed by the htu31 driver.
The driver creates a debugfs entry for the sensor serial number, but
the documentation currently only describes the sysfs interface.
Signed-off-by: Chen-Shi-Hong <eric039eric@gmail.com>
Link: https://lore.kernel.org/r/20260517125320.2196-1-eric039eric@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Murata D1U74T-W series are hot-pluggable 1U AC/DC front-end
power supplies in the Intel CRPS-185 / OCP M-CRPS form factor.
Each variant delivers a 12 V main output plus a 12 V standby output
from a wide AC input (90-264 Vac) or HVDC supply, and includes an
internal variable-speed cooling fan and on-board voltage, current,
power, fan-speed, and temperature telemetry.
The host-side digital interface is a PMBus 1.2 port on I2C. The
PSU's other electrical signals (status, alert, current-share) live
on the CRPS edge connector and are consumed by the chassis
controller rather than the host SoC, so there are no host-described
supplies, GPIOs, clocks, or interrupts. Add the compatible to
trivial-devices.yaml rather than carrying a standalone binding file.
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260514-d1u74t-v4-1-1f1ee7b002ec@nexthop.ai
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hardcoded maximum of 512 cores per package was first defined by commit
34cf8c657c ("hwmon: (coretemp) Enlarge per package core count limit")
and later kept as a fallback with a TODO in commit 1a793caf6f ("hwmon:
(coretemp) Use dynamic allocated memory for core temp_data") because the
actual per-package core count was not reliably available at the time.
Now that topology_num_cores_per_package() is stable and suitable for use,
it's time to complete the TODO and allocate only the needed amount of
memory for core_data.
Signed-off-by: Roman Bakshansky <bakshansky.lists@gmail.com>
Link: https://lore.kernel.org/r/20260516114253.5466-2-bakshansky.lists@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7411 driver exposes additional standard hwmon attributes beyond
the ones currently listed in Documentation/hwmon/adt7411.rst.
Document voltage min/max/alarm attributes, temperature min/max and
min_alarm/max_alarm attributes, and the temp2_fault attribute for the
external temperature channel.
Also update the documentation to clarify that analog inputs in1 and in2
are not available when the external temperature sensor is enabled, and
remove the outdated statement claiming that external temperature support
and limit registers are unsupported.
Signed-off-by: Chen-Shi-Hong <eric039eric@gmail.com>
Link: https://lore.kernel.org/r/20260516035245.1604-1-eric039eric@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADM1266 reports its firmware revision via the IC_DEVICE_REV
manufacturer-specific block-read command (0xAE, datasheet Rev. D
Table 80). The first three returned bytes are the firmware
major.minor.patch fields. This is useful when correlating field
behaviour against ADI release notes; expose it through debugfs
alongside the existing sequencer_state entry.
The standard PMBus MFR_REVISION (0x9B) register is already exposed
by pmbus_core's debugfs auto-create path and reports the
manufacturer revision, which is a separate thing from the firmware
running on the device.
Signed-off-by: Abdurrahman Hussain <abdurrahman@nexthop.ai>
Link: https://lore.kernel.org/r/20260512-adm1266-v3-1-a81a479b0bb0@nexthop.ai
[groeck: Squashed patch adding serialization with pmbus_lock]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The nct7802 chip exposes two registers that allow setting the time
interval between successive duty increases or decreases in Smart Fan
mode. The units are intervals of 0.1 second. The default value at power
on is 10, so 1 second.
Add sysfs attributes for step_up_time and step_down_time to allow
controlling the responsiveness of the fan speed. Values are represented
as milliseconds to the user. When set, the value is clamped to the valid
range of 100 to 25500 (0.1 to 25.5 seconds), and rounded to the nearest
multiple of 100.
Signed-off-by: Ronan Dalton <ronan.dalton@alliedtelesis.co.nz>
Cc: linux-kernel@vger.kernel.org
Cc: linux-hwmon@vger.kernel.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20260514003404.1548747-2-ronan.dalton@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
The mentioned robustness is relevant for a planned change to struct
i2c_device_id that replaces .driver_data by an anonymous union.
While touching all these arrays, unify indention and usage of commas.
This patch doesn't modify the compiled arrays, only their representation
in source form benefits. The former was confirmed with x86 and arm64
builds.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/65b77bcd452752c36d866069cc5790b26d2bf8dc.1778688803.git.u.kleine-koenig@baylibre.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The four drivers all don't make use of the value that was explicitly
assigned to the .driver_data member. Drop the assignment.
While touching these lines also make the assignments use named
initializers and drop a comma after the end-of-list marker.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # For
Link: https://lore.kernel.org/r/e8ceb3931975813545a8b478cc1a71b4ede9a6c0.1778688803.git.u.kleine-koenig@baylibre.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't make use of the i2c .driver_data and the of .data. So
drop the useless and irritating assignments.
While touching all these lines, use named initializers for the i2c
device ids and convert to the most common usage of spacing in such
arrays.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/dcfcc82a93da77b55503998c5c7acf2a80c4a615.1778603083.git.ukleinek@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replace of_property_read_string() with the preferded
device_property_read_string() in the probe function to
read the device label property, improving the driver
compatibility since this method is not limited to
Device Tree only.
Also drop the now unnecessary __maybe_unused from tmp102_of_match.
Signed-off-by: Flaviu Nistor <flaviu.nistor@gmail.com>
Link: https://lore.kernel.org/r/20260510092543.12352-1-flaviu.nistor@gmail.com
Link: https://lore.kernel.org/r/20260518122210.10288-1-flaviu.nistor@gmail.com
[groeck: Combined API change with __maybe_unused patch]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add hwmon driver for the ARCTIC Fan Controller, a USB HID device
(VID 0x3904, PID 0xF001) with 10 fan channels. Exposes fan speed in
RPM (read-only) and PWM duty cycle (0-255, read/write) via sysfs.
The device pushes IN reports at ~1 Hz containing RPM readings. PWM is
set via OUT reports; the device applies the new duty cycle and sends
back a 2-byte ACK (Report ID 0x02). The driver waits up to 1 s for
the ACK using a completion. Measured device latency: max ~563 ms over
500 iterations. PWM control is manual-only: the device never changes
duty cycle autonomously.
raw_event() may run in hardirq context, so fan_rpm[] is protected by
a spinlock with irq-save. pwm_duty[] is also protected by this spinlock
because reset_resume() clears it outside the hwmon core lock. The OUT
report buffer is built and write_pending is armed under the same lock so
that no reset_resume() can race with the pwm_duty[] snapshot. priv->buf
is exclusively accessed by write(), which the hwmon core serializes.
Signed-off-by: Aureo Serrano de Souza <aureo.serrano@arctic.de>
Link: https://lore.kernel.org/r/20260508064405.38676-1-aureo.serrano@arctic.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
