tas2563_save_calibration() assigns cali_data.total_sz before it reads the
per-device calibration data from EFI, but its error paths return without
clearing it again. cali_data.cali_reg_array is left all zero, because the
function returns before the register addresses are assigned.
On the first playback tasdev_load_calibrated_data() does
if (!data || !cali_data->total_sz)
return;
which passes, since total_sz is still non-zero. It then issues five
4-byte bulk writes to p->r0_reg, p->r0_low_reg, p->invr0_reg, p->pow_reg
and p->tlimit_reg, all of which are 0. Register 0 decodes to book 0 /
page 0 / register 0x00, so the auto-incrementing block write zeroes
registers 0x00 to 0x03. Register 0x03 is PB_CFG1, which holds AMP_LEVEL,
so the amplifier gain is set to its minimum and the speaker stays silent.
This is reproducible on a Lenovo Yoga 7 14ARB7 (two TAS2563 on I2C,
ACPI INT8866) whose factory calibration was never written to UEFI, so the
EFI read fails with EFI_NOT_FOUND. The two woofers driven by the
amplifiers are silent while the tweeters driven directly by the ALC287
play. Reading the amplifier registers over i2c shows PWR_CTL = 0x00
(active) and the TDM slots correctly programmed by the RCA profile, but
PB_CFG1 = 0x00. With this change PB_CFG1 keeps its power-on default of
0x20 and both woofers play.
tas2781_save_calibration() in tas2781_hda.c already clears total_sz on
failure; do the same for the TAS2563 variant.
Signed-off-by: Philipp Oster <philippdev5396@outlook.de>
Link: https://patch.msgid.link/20260720-tas2781-calfix-v1-1-3a5fa6ad90bc@outlook.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a codec SSID quirk for Samsung ELECTRONICS 750XBE/730XBE using
HDA_CODEC_QUIRK() instead of SND_PCI_QUIRK(), because the alsa-info
report from this device does not expose a PCI subsystem ID, only the
HDA codec subsystem ID (0x144d:0xc824) is available.
This applies ALC298_FIXUP_SAMSUNG_HEADPHONE_VERY_QUIET to fix sound
being very low and distorted on the headphone jack of this system.
Reported-by: Caio Ramos <caioramos97@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208663
Signed-off-by: Zhang Heng <zhangheng@kylinos.cn>
Link: https://patch.msgid.link/20260720123702.799474-1-zhangheng@kylinos.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The firmware on the Lunnen Ground 14 marks pin 0x1b as unused even
though the internal speakers are connected to it. As a result, the
speakers are not detected.
Add a pin configuration quirk for PCI subsystem ID 2782:a212 to configure
pin 0x1b as an internal speaker.
The pin configuration was tested on a Lunnen Ground 14 (DMI product LL4FA)
with an ALC269VC codec. The internal speakers and microphone work as
expected.
Cc: stable@vger.kernel.org
Signed-off-by: Nikita Maksimov <nickstogramm@yandex.ru>
Link: https://patch.msgid.link/20260720180214.73770-1-nickstogramm@yandex.ru
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP Pavilion x360 sets a bogus PCI SSID (103c:0000), hence the driver
picks up a wrong quirk entry, resulting in an almost silent output.
And yet, the existing quirk for x390 doesn't seem sufficing, and we
need the extra setup for the amp.
This patch adds the quirk entry for the codec SSID (103c:8486) to
initialize the amp via COEF verbs and chains to the existing quirk for
another x360 model to address the silent output.
Closes: https://lore.kernel.org/CAF2ktaUW2oaWwGazGtJQ3o1JyE2R4O2xPd-Dchr=qqi7_QRruQ@mail.gmail.com
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260716064916.540616-1-tiwai@suse.de
HP ZBook 8 G2a 14 and 16 (SSIDs 0x103c:0x8f94, 0x103c:0x8f95) use the
Realtek ALC245 codec with a TAS2781 amplifier via I2C. They share the same
hardware configuration as the existing 0x8f40/0x8f41/0x8f42/0x8f62 models
but have inverted speaker mute LED polarity, so the existing
ALC245_FIXUP_HP_TAS2781_I2C_MUTE_LED quirk drives the LED backwards: off
when muted and on when unmuted.
Add a dedicated quirk with inverted COEF values. These are speaker-only
models without an HP pin, so the LED is driven directly through the
vmaster_mute hook; there is no need to probe the HP pin at runtime since
the configuration is static and known per SSID.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Link: https://patch.msgid.link/20260716023825.387532-1-chris.chiu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a keep-alive (KAE) silent stream is active on an Intel HDMI/DP
codec, opening a real PCM stream reprograms the converter format and the
audio infoframe in snd_hda_hdmi_generic_pcm_prepare(). Part of that
reprogramming - the converter channel count and the channel mapping in
snd_hda_hdmi_setup_audio_infoframe() - is not safe to do while a
keep-alive stream is active. This is most visible when switching to a
multichannel PCM configuration, where the active channel count actually
changes. In that case the newly opened PCM stream plays no sound.
Add an optional hdmi_ops .prepare hook, called at the start of the
PCM prepare sequence (before the format and infoframe are touched), and
implement it for HSW+ to release keep-alive. Keep-alive is then
re-enabled as before once the new stream has been set up, in the
setup_stream op.
Fixes: 15175a4f2b ("ALSA: hda/hdmi: add keep-alive support for ADL-P and DG2")
Reported-by: Alexander Kaplan <alexander.kaplan@sms-medipool.de>
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/work_items/8412
Tested-by: Alexander Kaplan <alexander.kaplan@sms-medipool.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20260715180610.1371243-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
cs35l41_get_acpi_mute_state() evaluates a _DSM method to get the ACPI
mute state and reads the first byte from the returned object.
However, the returned ACPI object is owned by the caller and is never
freed after use, so each successful query leaks the _DSM result object.
The code also assumes that the returned object is a buffer with at least
one byte. A malformed firmware response can return a different object
type or an empty buffer, and the direct ret->buffer.pointer dereference
can then access an invalid pointer.
Use the typed _DSM helper, validate that the returned buffer contains at
least one byte, and free the ACPI object after reading it.
Fixes: 447106e92a ("ALSA: hda: cs35l41: Support mute notifications for CS35L41 HDA")
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Link: https://patch.msgid.link/20260708113625.752913-1-lgs201920130244@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Alienware x16 R2 has two pairs of speakers, but the BIOS
marks pin 0x17 as unused, so only the pin 0x14 pair plays and
audio is very quiet/dull.
Apply ALC289_FIXUP_DUAL_SPK like on other Dell machines to set
up pin 0x17 and route it to DAC1. Tested on my x16 R2 with
kernel 6.18.38, and now all speakers play at full volume.
Signed-off-by: Oliver Ohrt <oliver@theohrts.com>
Link: https://patch.msgid.link/20260715070409.42696-1-oliver@theohrts.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The sound and microphone mute LEDs do not function on this newer
revision of the board (8AB8) while they do on the older 880D models.
I have verified this on another laptop which was manufactured before
the one with the issue.
Added the ALC245_FIXUP_CS35L41_SPI_2_HP_GPIO_LED from a G9 model, which
uses the same codec, to make it work. Tested on kernel version 7.1.3 on
the aforementioned newer revision notebook.
Signed-off-by: Marcel Kłos <marcel@marmak.net.pl>
Link: https://patch.msgid.link/4dab5622-9100-4730-8c99-b58da939549b@marmak.net.pl
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the mic bias current comparator threshold override (NID 0x1c,
verb 0x320, value 0x010) from Conexant codec driver.
This override was originally intended to support volume up/down controls on
headsets with inline remote controls, but it causes microphone detection
failures on some headsets with impedance less than 1k ohm.
After consulting with the vendor's engineers, it was confirmed that this
setting is board-specific and should be handled by BIOS/firmware rather
than the generic codec driver, especially since inline remote support
is not currently implemented.
Fixes: 7aeb259086 ("ALSA: hda/conexant: Fix headset auto detect fail in cx8070 and SN6140")
Cc: stable@vger.kernel.org
Signed-off-by: Zhang Heng <zhangheng@kylinos.cn>
Link: https://patch.msgid.link/20260713100329.306892-1-zhangheng@kylinos.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some units of the Lenovo Legion Pro 7 16ARX8H (82WS) report codec
subsystem ID 17aa:38a7 instead of 17aa:38a8. Since only 38a8 has a
codec SSID quirk, these machines fall through to the PCI SSID match
17aa:386f (Legion Pro 7i 16IAX7) and get ALC287_FIXUP_CS35L41_I2C_2,
which probes the Cirrus amplifiers of the Intel variant. The TI
TAS2781 amplifier (ACPI TIAS2781:00) present on this AMD variant is
never bound and the internal speakers remain silent.
Add a codec SSID quirk for 17aa:38a7 pointing to
ALC287_FIXUP_TAS2781_I2C, mirroring the existing 38a8 entry.
Tested on a Legion Pro 7 16ARX8H (82WS, BIOS LPCN62WW): with the codec
SSID overridden to 17aa:38a8 via the HDA patch loader, the TAS2781
amplifier binds and the internal speakers work.
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Laine <damien.laine@gmail.com>
Link: https://patch.msgid.link/20260712213708.1835469-1-damien.laine@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The internal speakers on the MECHREVO WUJIE Series are silent,
while the headphone output works correctly.
The BIOS reports NID 0x1b on the Realtek ALC233 codec as
unconnected with pin configuration 0x411111f0. However, the pin
is connected to an internal speaker.
Overriding NID 0x1b with 0x90170150 makes the HDA generic parser
detect both 0x14 and 0x1b as speaker outputs and restores internal
speaker playback.
Add a pin configuration fixup for the affected PCI SSID c011:1d05.
Tested on a MECHREVO WUJIE Series laptop with board
WUJIE Series-Lark4-LNL and firmware EM_LNL326_V1.0.23.
Signed-off-by: Chen Bowen <hicbowen@gmail.com>
Link: https://patch.msgid.link/20260710133409.16641-1-hicbowen@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fail cs35l56_hda_fw_load() and log an error if it didn't find a wmfw file
and the BIOS didn't patch the firmware already. Also remove a section of
code from cs35l56_hda_request_firmware_files() that attempted to find a
.bin if a .wmfw was not found.
The CS35L56 ROM can only provide default audio in SoundWire mode. A wmfw
is needed to enable I2S audio. Also none of the customer-specific .bin
files are compatible with the ROM firmware. So a .wmfw file is always
required.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260709161211.686498-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the Kconfig item for cirrus_scodec visible if CONFIG_KUNIT is
enabled. This is so that its KUnit test can be enabled by KUnit
scripts without requiring a large amount of irrelevant additional
components.
The general rule for KUNIT_ALL_TESTS is that it should only enable
tests for components that are already selected. However, the UML
environment does not support ACPI, which means the HDA codec drivers
that use cirrus_scodec cannot be selected. But cirrus_scodec does not
need ACPI.
By making the Kconfig option visible if CONFIG_KUNIT, the KUnit test
can be enabled with only the minimal set of functionality that is
required for cirrus_scodec.
This is still compliant with the KUNIT_ALL_TESTS rule "only tests
for enabled modules" because by default cirrus_scodec will only be
enabled if the drivers that use it are enabled. It must be
intentionally enabled to force it to be included for testing.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260709121224.614350-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This platform booted with Ubuntu 24.04 with Pipewire audio server. So,
it has pop noise with headphone. But it's normal with Pulseaudio server.
This patch was the workaround. Connect the headphones to DAC 0x2.
The popping sound will disappear.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/34b990cb56914148ba02fa8e9d176479@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP Laptop 15-fd0xxx uses GPIO bit 0 to control the mic mute LED,
but currently the quirk only enables the speaker mute LED (via coef
bit). Switch to the existing ALC236_FIXUP_HP_MUTE_LED_MICMUTE_GPIO
fixup which additionally registers a GPIO-based mic mute LED, mapping
to the same verbs (SET_GPIO_DATA/SET_GPIO_DIRECTION bit 0) that the
platform firmware uses.
Signed-off-by: Kshamendra Kumar Mishra <kshamendrakumarmishra@gmail.com>
Link: https://patch.msgid.link/DJSOWKFBTJH8.2Z7EPWX514QXM@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mute LED on HP Victus 15-fa0xxx (board ID 8A50) uses ALC245 but
requires a quirk to work. This patch enables the existing
ALC245_FIXUP_HP_MUTE_LED_COEFBIT quirk for the device.
Tested on my HP Victus 15-fa0xxx. The LED behaviour works as intended.
Signed-off-by: Rohit Sinha <rohitsinha12043@gmail.com>
Link: https://patch.msgid.link/20260706211834.384022-1-rohitsinha12043@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ASUS ROG Ally X (RC72LA, PCI SSID 0x1043:0x1eb3) leaves the combo
jack microphone pin (0x19) unconfigured, so a headset microphone is
neither detected nor captured. Only the internal microphone is
available.
Add a pin override that configures node 0x19 as an external headset
mic, the same way the original ROG Ally does. The headphone output
fixup chain is preserved, so speaker and headphone routing are
unchanged.
Signed-off-by: Matthew Schwartz <matthew.schwartz@linux.dev>
Link: https://patch.msgid.link/20260707005615.52889-2-matthew.schwartz@linux.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ASUS ROG Ally X (RC72LA, PCI SSID 0x1043:0x1eb3) with an ALC294
codec produces no sound from the headphone jack, and unplugging the
headphones can leave the speakers muted too.
The device uses ALC287_FIXUP_TAS2781_I2C, which chains into the
ThinkPad fixup chain. alc285_fixup_thinkpad_x1_gen7() makes the
headphone (pin 0x21) and speaker (pin 0x17) share DAC 0x03. That is
correct for a ThinkPad, but here the shared DAC is exposed as a
"Line Out" control that defaults to zero, so the headphones stay
silent when plugged in.
Add a dedicated fixup chain for the Ally X that sets up the TAS2781
amplifier and the headset jack without the ThinkPad DAC sharing, and
routes the speaker to DAC 0x02 so the headphone and speaker get
independent DACs.
Also, fixup the wrong product code (it's RC72LA, not RCLA72).
Signed-off-by: Matthew Schwartz <matthew.schwartz@linux.dev>
Link: https://patch.msgid.link/20260707005615.52889-1-matthew.schwartz@linux.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A standard set of driver-specific fixes and quirks accumulated since
the merge window:
ASoC:
- SOF: Sanity check to prevent OOB reads
- rsnd: Fix clock leak and double-disable issues with PM
- tas675x: Misc fixes for register fields, etc
- lpass-va-macro: Correct codec version for Qualcomm SC7280
- amd-yc: DMIC quirk for Alienware m15 R7 AMD
Others:
- us144mkii: Fix a UAF on disconnect and anchor list corruption
- HD-audio: Realtek quirks for HP models
-----BEGIN PGP SIGNATURE-----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=eXcj
-----END PGP SIGNATURE-----
Merge tag 'sound-7.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A standard set of driver-specific fixes and quirks accumulated since
the merge window:
ASoC:
- SOF: Sanity check to prevent OOB reads
- rsnd: Fix clock leak and double-disable issues with PM
- tas675x: Misc fixes for register fields, etc
- lpass-va-macro: Correct codec version for Qualcomm SC7280
- amd-yc: DMIC quirk for Alienware m15 R7 AMD
Others:
- us144mkii: Fix a UAF on disconnect and anchor list corruption
- HD-audio: Realtek quirks for HP models"
* tag 'sound-7.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: rsnd: src: Add missing scu_supply clock to suspend/resume
Documentation: sound: tas675x: Fix temperature range and impedance documentation
ASoC: codecs: tas675x: Fix CHx temperature range register bit fields
ASoC: codecs: tas675x: use READ_ONCE for params to be used concurrently
ASoC: rsnd: adg: make rsnd_adg_clk_control() idempotent
ASoC: SOF: validate probe info element counts
ALSA: usx2y: us144mkii: fix work UAF on disconnect
ASoC: amd: yc: Add Alienware m15 R7 AMD to DMIC quirk table
ALSA: hda/realtek: Add quirk for HP Victus 16-e0xxx (88EE) to enable mute LED
MAINTAINERS: ASoC: SOF: add AMD reviewer for Sound Open Firmware
ASoC: codecs: lpass-va-macro: Fix LPASS Codec Version for SC7280
ALSA: us144mkii: capture_urb_complete: redundant usb_anchor_urb corrupts anchor list on each resubmission
Similar to commit 67c7381522 ("ALSA: hda/realtek: fix mic boost on
Framework PTL") and previous quirks for Framework systems with
Realtek codecs.
0010 is another platform with an ALC285 which needs the same quirk.
Signed-off-by: Daniel Schaefer <dhs@frame.work>
Link: https://patch.msgid.link/20260705-framework-audio-ssid-0x0010-v1-1-fffc8996ac18@frame.work
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP Laptop 15-dw0xxx with subsystem ID 103c:85f0 needs the
ALC236_FIXUP_HP_MUTE_LED_COEFBIT2 quirk to correctly disable and
enable the Audio Mute LED.
Add the missing quirk entry.
Signed-off-by: Federico Lombardo <lombardo.federico.lf@gmail.com>
Link: https://patch.msgid.link/20260702204347.187524-1-lombardo.federico.lf@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the #include of <linux/mod_devicetable.h> by the more specific
<linux/device-id/*.h> where applicable. For most cases the include
can be dropped completely, only a few drivers need one or two headers
added.
Acked-by: Danilo Krummrich <dakr@kernel.org>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/1a3f2007c5c5dcf555c09a4035ce3ae8ef1b6c49.1782808461.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
The mute LED on the HP Victus 16-e0xxx (board ID 88EE, ALC245 codec)
does not function by default. Add the ALC245_FIXUP_HP_MUTE_LED_COEFBIT
quirk to enable it. Tested on my HP Victus 16-e0xxx with kernel 7.1.2.
Signed-off-by: Shubham Nayak <shubhamnayak392reborn@gmail.com>
Link: https://patch.msgid.link/20260629-hp-victus-16-mute-led-v1-1-ab0f4a8a533b@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The laptop has a microphone mute LED on the F4 key, but it was not
taken in mind when the previous quirk was added
in commit 00e44a68ef ("ALSA:
hda/realtek: Add quirk for Acer Nitro ANV15-41").
Replace ALC2XX_FIXUP_HEADSET_MIC with ALC245_FIXUP_ACER_MICMUTE_LED,
which enables the LED and chains the previous quirk for the headset
microphone.
Fixes: 00e44a68ef ("ALSA: hda/realtek: Add quirk for Acer Nitro ANV15-41")
Signed-off-by: Oleg Kucheryavenko <oleg.kucheryavenko2018@gmail.com>
Link: https://patch.msgid.link/20260625134955.27465-1-oleg.kucheryavenko2018@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo Legion 7i 16IAX7 systems with Realtek ALC287 codec SSID
17aa:3874 and CSC3551/CS35L41 speaker amps do not provide the
required CS35L41 _DSD properties in ACPI.
Without a quirk, cs35l41-hda fails probing the amps with missing
cirrus,dev-index / Platform not supported errors, leaving the built-in
speakers silent.
This model is similar to the already-supported 17AA386F Legion 7i
16IAX7 variant. Add the Realtek ALC287 quirk to select
ALC287_FIXUP_CS35L41_I2C_2 and add 17AA3874 to the CS35L41 property
table using the same two-amp external-boost configuration.
Tested on a Lenovo Legion 7 16IAX7 with Ubuntu 7.0.0-22-generic. Both
CSC3551 CS35L41 amps probe and bind, firmware loads, calibration
applies, built-in speaker playback works, and the cirrus,dev-index
failure is gone.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221663
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2157060
Signed-off-by: Kamlesh Chhetty <kamleshkc2002@gmail.com>
Link: https://patch.msgid.link/20260622172247.19301-1-kamleshkc2002@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Acer Nitro ANV15-41 laptop with ALC245 codec does not
detect the headset microphone in the combo jack by default.
Apply the ALC2XX_FIXUP_HEADSET_MIC quirk to fix it.
Signed-off-by: Oleg Kucheryavenko <oleg.kucheryavenko2018@gmail.com>
Link: https://patch.msgid.link/20260624191301.10162-1-oleg.kucheryavenko2018@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Yoga 7 16IAP7 (board LNVNB161216, codec SSID 17aa:386a) has pin
complex 0x17 (bass speakers) wrongly reported as unconnected, causing
only one of four speaker pins (0x14) to be configured and resulting in
mono/tinny audio.
SOF corrupts the PCI subsystem ID to 17aa:0000, preventing SND_PCI_QUIRK
from matching. HDA_CODEC_QUIRK is used instead, which matches against
codec->core.subsystem_id read directly from the HDA codec register and
unaffected by the SOF bug.
Applies ALC287_FIXUP_YOGA9_14IAP7_BASS_SPK_PIN, the same fixup used for
the Yoga 7 14IAL7, which corrects pin 0x17's default configuration and
enables both speaker pairs.
Signed-off-by: Chris Aherin <chrisaherin@gmail.com>
Link: https://patch.msgid.link/20260622001210.20553-1-chrisaherin@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP EliteBook 840 G6 (PCI SSID 103c:854d) has an ALC215 codec whose
mic-mute and audio-mute LEDs are wired to the same GPIOs as the already
supported EliteBook 830 G6 and 840 G7. Without a matching quirk the LEDs
are never registered, so the front-panel mic-mute LED stays permanently
lit and does not track the mute state.
Apply ALC285_FIXUP_HP_GPIO_LED, mirroring the sibling EliteBook entries.
With this fixup the codec registers an "hda::micmute" LED class device and
the LED correctly follows the capture-mute state. This was verified on the
affected machine by forcing the same fixup at runtime via
snd_sof_intel_hda_generic.hda_model=103c:8548, which made the LED work as
expected.
Signed-off-by: Ramcharan Rajpurohit <b23ci1032@iitj.ac.in>
Link: https://patch.msgid.link/20260619062435.26256-1-b23ci1032@iitj.ac.in
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acer S40-54 with ALC256 does not restore headset mic detection properly
after S4 resume. After resume, headset plug events may no longer update
the headset mic state, leaving the headset microphone unavailable.
The system uses subsystem ID 1025:161f. Applying the existing
ALC256_FIXUP_ACER_MIC_NO_PRESENCE fixup restores headset mic detection
on this machine.
Add a machine-specific quirk for this system.
Signed-off-by: Haowen Tu <tuhaowen@uniontech.com>
Link: https://patch.msgid.link/20260618075431.1116988-1-tuhaowen@uniontech.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo IdeaPad Slim 5 16AKP10 (PCI SSID 17aa:38b6) uses the
Conexant SN6140 codec. The internal microphone is on pin 0x1a but
the BIOS configures it with pin default 0x95a60120, which includes
a jack detection bit that causes the kernel to treat it as an
unplugged external mic rather than a fixed internal mic.
Add a pin config quirk that overrides pin 0x1a to 0x95a60130,
setting the connectivity bits to indicate a fixed/always-connected
device. This allows the internal microphone to be correctly
identified and used.
Signed-off-by: Galen Hassen <rwekyes@gmail.com>
Link: https://patch.msgid.link/20260616173257.37373-1-rwekyes@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There's been quite a lot of framework improvements this time around,
though mainly cleanups and robustness rather than user visible features.
The same pattern is seen with a lot of the driver work that's going on,
there are new features but a huge proportion of this is bug fixing and
cleanup work. We also have a good selectio of new device support.
- Improvements to SDCA jack handling from Charles Keepax.
- Use of device links to make suspend handling more robust from Richard
Fitzgerald.
- Use of a new helper to factor out a common pattern in SoundWire
enmeration from Charles Keepax.
- Slimming down of the component from Kuninori Morimoto.
- Simplification of format auto selection from Kuninori Morimoto.
- Lots of conversions to guard() from Bui Duc Phuc.
- Addition of a simple-amplifier driver supporting more featureful GPIO
controller amplifiers than the previous basic driver from Herve
Codina.
- Support for AMD ACP 7.x, Cirrus Logic CS42448/CS42888, Everest Semi
ES9356, Mediatek MT2701 and MT8196, Renesas RZ/G3E, Spacemit K3,
Texas Instruments TAC5xx2 and TAS67524.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmov9IgACgkQJNaLcl1U
h9BOYQf/fLQJlwAIQJu540syYQL9N7Lz/+6f41WEAeF86npaz1wvggwX7rWsOlCB
f+6bGiQ/QvYGrDlKBoIRvbrcUosYo5RcPveBhLUeYQ6w2wyhYR5bjF77YMFHHIWm
h+8wG4Cf59SnAvQ2sdctcKgaCbnJgN8IfTIhdGDQwDi2vf9AUO7o4pfKXO/wligq
4vBeuFLM+WgU5x0VhvwIU6yfa8MGSMvf/oX0bn3xYjOp2LyHzdfRGvoY/wa+6pFd
9QX2QsU6Yjrt5/zvuENwOq+nb3NbdDDqdQK8PRDnzYsbhpFj1RA5XRVShhk89h3F
TZyRqht++Vfs0b3CNW1Q59XZgxNX8A==
=3lzj
-----END PGP SIGNATURE-----
Merge tag 'asoc-v7.2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v7.2
There's been quite a lot of framework improvements this time around,
though mainly cleanups and robustness rather than user visible features.
The same pattern is seen with a lot of the driver work that's going on,
there are new features but a huge proportion of this is bug fixing and
cleanup work. We also have a good selectio of new device support.
- Improvements to SDCA jack handling from Charles Keepax.
- Use of device links to make suspend handling more robust from Richard
Fitzgerald.
- Use of a new helper to factor out a common pattern in SoundWire
enmeration from Charles Keepax.
- Slimming down of the component from Kuninori Morimoto.
- Simplification of format auto selection from Kuninori Morimoto.
- Lots of conversions to guard() from Bui Duc Phuc.
- Addition of a simple-amplifier driver supporting more featureful GPIO
controller amplifiers than the previous basic driver from Herve
Codina.
- Support for AMD ACP 7.x, Cirrus Logic CS42448/CS42888, Everest Semi
ES9356, Mediatek MT2701 and MT8196, Renesas RZ/G3E, Spacemit K3,
Texas Instruments TAC5xx2 and TAS67524.
The Lenovo Xiaoxin 14 GT (Chinese market model, AMD Ryzen AI 9 365)
produces constant electrical hissing and crackling noise from both
internal speakers and 3.5mm headphone jack during audio playback.
Audio works correctly on Windows.
The PCI SSID 17aa:3912 is not present in the quirk list. The device
shares the same AMD platform and ALC287 codec as neighboring Lenovo
14" AMD models (17aa:3911, 17aa:390d), so apply the same fixup.
Note: the fixup selection is based on similarity with neighboring
models and has not been verified by testing a compiled kernel.
Guidance from maintainers on the correct fixup is welcome.
Signed-off-by: Viktor Menshin <ripeeerr@gmail.com>
Link: https://patch.msgid.link/20260615092515.1082-1-ripeeerr@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ASUS Zenbook 14 UM3405GA uses a Realtek ALC294 codec with two
Cirrus Logic CS35L41 speaker amplifiers exposed through the CSC3551 ACPI
device. The machine reports the Realtek subsystem ID 1043:19f4.
Without a PCI quirk, the codec falls back to generic pin matching and the
internal speakers remain silent even though PCM playback completes.
Add the UM3405GA subsystem ID and reuse the same ASUS I2C headset-mic
fixup used by the closely related UM3406HA. That fixup configures the
headset microphone pin and chains to CS35L41 I2C speaker-amp binding.
Signed-off-by: Colton Jones <cjones1308@pm.me>
Link: https://patch.msgid.link/20260615033619.7-1-cjones1308@pm.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP EliteDesk 800 G5 Mini (PCI subsystem 103c:8595) uses
Cannon Lake PCH cAVS HDA with DisplayPort audio pins 0x05 and
0x06 set to AC_JACK_PORT_NONE (N/A) in BIOS defaults, causing
hdmi_add_pin() to skip them and the DP audio device to not
appear in ALSA.
Add the board to the existing force_connect_list alongside the
similar HP EliteDesk 800 G4 entries.
Signed-off-by: Cameron Graham <cam.graham@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20260612094601.1209845-1-cam.graham@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP 255 15.6 inch G9 Notebook PC (PCI SSID 103c:8a1b) uses the
ALC236 codec but lacks an entry in the quirk table, causing the kernel
to fall back to a null SSID match (103c:0000) and skip the necessary
fixup. Add a quirk entry using ALC236_FIXUP_HP_MUTE_LED_COEFBIT2,
matching the HP 255 G8 which uses the same codec and fixup. This fixes
the mute-button LED and fixes an issue with unplugging and replugging a
headset jack not being recognized as an audio sink.
Signed-off-by: Furst Blumier <seal@furst.blue>
Link: https://patch.msgid.link/20260609201706.502075-1-seal@furst.blue
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix reset for device-0: In older projects (e.g., Merino), the hardware
reset pin for the first SPI device (device-0) is ineffective, causing
initialization failures. Added a software reset sequence for device-0
to ensure proper initialization.
Handle -EXDEV correctly: When processing block data, if the data does
not belong to the current SPI device, the driver returned -EXDEV.
This error code is now ignored to allow the driver to continue iterating
through the block data and correctly calculate the total block size.
Signed-off-by: Baojun Xu <baojun.xu@ti.com>
Link: https://patch.msgid.link/20260609105253.19510-1-baojun.xu@ti.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo Yoga Pro 7 14IRH8 (ALC287 codec, subsystem ID 0x17aa:0x38b1)
has bass speakers on pin 0x17 that are not routed through a DAC with
volume control. This causes the bass speakers to play at full volume
regardless of the volume slider position.
Apply ALC287_FIXUP_YOGA9_14IAP7_BASS_SPK_PIN which corrects the DAC
routing for pin 0x17, enabling proper volume control. This is the same
fix used for other Yoga Pro 7 models with identical audio topology
(14APH8, 14AHP9, 14ASP10, 14IAH10).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217949
Co-developed-by: Felix Aljoscha Schnuell <felix.aljoscha.schnuell@stud.uni-hannover.de>
Signed-off-by: Felix Aljoscha Schnuell <felix.aljoscha.schnuell@stud.uni-hannover.de>
Signed-off-by: Moritz Baron <moritz.baron@stud.uni-hannover.de>
Link: https://patch.msgid.link/20260609141648.60608-1-moritz.baron@stud.uni-hannover.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The internal microphone on ASUS VivoBook X509DAP (subsystem ID
0x1043:0x197e) is not detected without a quirk entry. Add
ALC256_FIXUP_ASUS_MIC_NO_PRESENCE to fix the issue.
Signed-off-by: Andrei Faleichyk <andrei.faleichyk@noogadev.com>
Link: https://patch.msgid.link/20260603213313.6298-1-andrei.faleichyk@noogadev.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clevo P775TM1 laptops come with an ESS Sabre HiFi DAC. Setting
0x1b pin VREF to 80% enables said DAC output.
Signed-off-by: Evelyn Ali <evelynali99@gmail.com>
Link: https://patch.msgid.link/20260602214122.78020-1-evelynali99@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Alexey Charkov <alchark@flipper.net> says:
The Nuvoton NAU8822 codec has four power supply pins: VDDA, VDDB, VDDC
and VDDSPK, which must be online and stable before the device can be
accessed over I2C. On boards where these rails are software-controlled,
probing the codec before the regulators are up results in -ENXIO errors
during register access.
This short series adds optional regulator support to both the device
tree binding and the driver, so platforms that need explicit power
sequencing can describe and enforce it:
Link: https://patch.msgid.link/20260525-nau8822-reg-v2-0-7d37ae393e46@flipper.net
Lenovo Yoga Pro 7 15ASH11 with AMD RYZEN AI MAX+ 388 (Strix Halo, ACP
7.0) uses Realtek ALC287 series codec. The ALC269_FIXUP_LENOVO_XPAD_ACPI
in alc269_fixup_vendor_tbl[] can load lenovo_wmi_hotkey_utilities module
by default in this laptop, but the driver doesn't control mic mute LED.
If users run below command and the mic mute LED can work normally.
$sudo echo 'Capture Switch' >/sys/class/sound/ctl-led/mic/card1/attach
After added the SND_PCI_QUIRK quirk special for Lenovo Yoga Pro 7
15ASH11, the mic mute LED works well.
Fixes: 83dca2530f ("ALSA: hda/realtek: ALC269 fixup for Lenovo Yoga Pro 7 15ASH111 audio")
Signed-off-by: Jackie Dong <xy-jackie@139.com>
Link: https://patch.msgid.link/20260527130353.5658-1-xy-jackie@139.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to a hardware defect, for Loongson PCI HDMI devices with a reversion
ID of 2, the pin sense status must be determined via the ELD.
Add a codec flag, eld_jack_detect, to indicate this case, and do special
handlings in read_pin_sense().
Cc: stable@vger.kernel.org
Signed-off-by: Baoqi Zhang <zhangbaoqi@loongson.cn>
Signed-off-by: Haowei Zheng <zhenghaowei@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://patch.msgid.link/20260527140841.3407183-1-chenhuacai@loongson.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
