ieee80211_rx_mgmt_deauth() reads the deauth reason code before checking
that the fixed field is actually present in the received frame.
Validate the deauth frame length first and only then read the reason
code.
Assisted-by: Codex:gpt-5.5
Assisted-by: Claude:claude-opus-4.8
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260612185042.66260-6-enderaoelyther@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When assoc_data->s1g is set and no AID Response element is present,
falling back to mgmt->u.assoc_resp.aid reads the non-S1G
association-response layout.
Keep the fallback for non-S1G only. If a successful S1G association
response omits the AID Response element, abandon the association
instead of proceeding with AID 0. Initialize aid to 0 for other S1G
responses so the later mask and logging flow keeps a defined value
without reading the non-S1G layout.
Fixes: 2a8a6b7c4c ("wifi: mac80211: handle station association response with S1G")
Assisted-by: Codex:gpt-5.5
Assisted-by: Claude:claude-opus-4.8
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
Link: https://patch.msgid.link/20260612152440.25955-2-enderaoelyther@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
UHR requires MLO, not just formally but also in order
for the client to understand AP BSS parameter changes,
since the Critical Update Counter is inside the Multi-
Link Element. Require MLO for UHR connections to avoid
otherwise needed complexity such as not enabling any
feature that would require tracking critical updates.
Link: https://patch.msgid.link/20260529102644.43817ce87042.If4562ae9c5ca83339b397d9a344b68631cb17c4a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When connected to a non-transmitting BSS of multiple BSSID
set with EMA, the correct profile for the connection isn't
always present in the beacon. Indicate this in the parser
and use the information to not check everything in beacon
processing, since the information might not be correct if
taken only from the transmitted BSS.
Link: https://patch.msgid.link/20260529102644.97527a7dfd7b.Iecd0ef578b85a5a0057538cfff5fdff41d19b7ea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are multiple cases where interface links are removed
and the station links need to be removed with them, e.g.
in mlme.c we have both received and transmitted multi-link
reconfiguration, doing the two things in different order,
the former deleting STA links when the vif link change may
still fail.
It's also not clear that userspace (hostapd) couldn't, at
least in theory, remove a link from an interface without
removing the station links first, or even leave stations
that aren't MLO-capable, using that link.
Unify this code into ieee80211_vif_update_links() so that
it always happens, always happens in the right order and
is transactional (i.e. failures are handled correctly.)
Link: https://patch.msgid.link/20260529102644.c352f73a4658.I7219a5d72dab2abcecea9b5c52e7eb7a50e68d9b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add KUnit coverage for ieee80211_parse_neg_ttlm() to lock the sparse
link_map_presence layout against future regressions.
The sparse_presence_no_oob_read case crafts a negotiated TTLM element
with link_map_presence = BIT(0) | BIT(7) and bm_size = 2 in a buffer
sized exactly to the validated element length. Without the parser
fix this would read 14 bytes past the buffer when processing TID 7;
under KASAN that is a slab-out-of-bounds report.
The dense_presence_baseline case crafts a fully populated
link_map_presence = 0xff element to confirm that the cursor-advance
fix does not regress the path that was already correct.
Export ieee80211_parse_neg_ttlm via VISIBLE_IF_MAC80211_KUNIT so the
test can call it directly.
Assisted-by: Claude:claude-sonnet-4-6
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Link: https://patch.msgid.link/20260515151719.1317659-3-michael.bommarito@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_tid_to_link_map_size_ok() validates negotiated TTLM elements
against the number of link-map entries indicated by link_map_presence.
ieee80211_parse_neg_ttlm() must consume the same layout.
The parser advanced its cursor for every TID, including TIDs whose
presence bit is clear and therefore have no map bytes in the element.
A sparse map can then make a later present TID read past the validated
element.
The bad bytes land in neg_ttlm->{up,down}link[tid] but are gated by
valid_links before being applied to driver state, so a peer cannot
turn the read into a policy change. Under KUnit + KASAN with an
exact-sized element allocation the OOB read is reported as a
slab-out-of-bounds; whether the same trigger fires under the
production RX path depends on surrounding allocator state.
Advance the cursor only when the current TID has a map present.
Fixes: 8f500fbc6c ("wifi: mac80211: process and save negotiated TID to Link mapping request")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Link: https://patch.msgid.link/20260515151719.1317659-2-michael.bommarito@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE80211_MLE_STA_EPCS_CONTROL_LINK_ID is 0x000f, so link_id extracted
from a PRIO_ACCESS ML element PER_STA_PROFILE subelement can be 0..15.
sdata->link[] has IEEE80211_MLD_MAX_NUM_LINKS (15) entries (indices 0..14),
making index 15 out-of-bounds.
A connected WiFi 7 AP can trigger this by sending an EPCS Enable Response
action frame with a PER_STA_PROFILE subelement where link_id = 15. The
unsolicited-notification path (dialog_token = 0) is reachable any time
EPCS is already enabled, without any prior client request.
sdata->link[15] reads into the first word of sdata->activate_links_work
(a wiphy_work whose embedded list_head is non-NULL after INIT_LIST_HEAD),
so the NULL check on the result does not catch the invalid access. The
garbage pointer is then passed to ieee80211_sta_wmm_params(), which
dereferences link->sdata and crashes the kernel.
The same class of bug was fixed for ieee80211_ml_reconfiguration() by
commit 162d331d83 ("wifi: mac80211: bounds-check link_id in
ieee80211_ml_reconfiguration").
Fixes: de86c5f608 ("wifi: mac80211: Add support for EPCS configuration")
Signed-off-by: Alexandru Hossu <hossu.alexandru@gmail.com>
Link: https://patch.msgid.link/20260515102908.1653088-1-hossu.alexandru@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If connection preparation fails for MLO connections, then the
interface is completely reset to non-MLD. In this case, we must
not keep the station since it's related to the link of the vif
being removed. Delete an existing station. Any "new_sta" is
already being removed, so that doesn't need changes.
This fixes a use-after-free/double-free in debugfs if that's
enabled, because a vif going from MLD (and to MLD, but that's
not relevant here) recreates its entire debugfs.
Cc: stable@vger.kernel.org
Fixes: 81151ce462 ("wifi: mac80211: support MLO authentication/association with one link")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260505151533.c4e52deb06ad.Iafe56cec7de8512626169496b134bce3a6c17010@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, as noted in the comment, ieee80211_uhr_oper_size_ok()
will reject the element coming from the beacon, since it's too
short. However, this is incorrect in general, since the element
is extensible, and such extensions could be present in a beacon,
and then it might pass muster anyway.
Using the frame type we now have in the element parse result,
check that it's not coming from a beacon. The size was already
checked (according to frame type) during parsing.
Link: https://patch.msgid.link/20260428112708.41a7aacdda0c.I0d83c8c9cbee41fd2599480cad815b94867aa1f8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When considering both NPCA and DBE, it can appear that the
NPCA configuration is invalid, e.g. for an 80 MHz BSS channel
with DBE to 160 MHz:
| primary channel
| NPCA primary channel
| |
V V
| p | | n | | | | | |
| BSS channel |
| DBE channel |
Now the NPCA primary channel is in the same half as the primary
channel, and the NPCA puncturing bitmap could be completely
invalid as a puncturing bitmap when considering the overall
channel.
Split out the validity checks from cfg80211_chandef_valid() to
a new cfg80211_chandef_npca_valid() function that just checks
the NPCA configuration against the BSS chandef.
Link: https://patch.msgid.link/20260428112708.1225df131557.If3a6afadcce05d215b72fd82175f72373a0f6d24@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the device is capable, parse the AP chandef with NPCA.
Also advertise the other NPCA operational parameters to the
underlying driver and track if they change (though not with
BSS critical update etc. yet)
Since NPCA can only be enabled when the chanctx isn't shared,
the channel context code needs to clear/set npca.enabled in
the per-link configuration, except during association since
we can't enable NPCA before having completed association. In
this case, set npca.enabled during the association process.
Link: https://patch.msgid.link/20260428112708.eb1e42c0b6d7.I0acd8445d4600363afb8430922531450399d0fab@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Put the NPCA parameters into a chandef when parsing data from
the AP to validate them using the cfg80211 code, rather than
implementing that in mac80211 directly.
Note that the parameters are not applied yet, since mac80211
doesn't yet have NPCA support.
Link: https://patch.msgid.link/20260428112708.418e86f9444c.I54430f3018e39a26b4252d71000d7bb7dd744331@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since 802.11bn D1.4 the DBE capabilities are after the
PHY capabilities, not between MAC and PHY, adjust the
code accordingly.
Also add a struct for DBE capabilities and use it for
checking the correct length instead of hard-coding the
lengths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260428103657.b40af50f182d.I75306a092dc2c8a9eb7276160f0b7144b4846d18@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The interface frame queue processing code currently
differentiates many frame types and below those the
interface types, but then falls through to per-type
processing. Move this code to the per-type functions,
creating a new ap.c file that gets relevant code, and
this way reduce the number of non-static symbols.
This also helps with adding more cases for UHR later.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260428103649.c00059e68a07.I2269130278390f534d6051fac424402a854a54aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Populate the assoc_encrypted field in cfg80211_rx_assoc_resp_data
for mac80211-based drivers to indicate that the entire (re)association
exchange was encrypted.
When epp_peer is set, mac80211 enforces that unprotected
(Re)Association Request/Response frames are dropped. This ensures that
by the time the (Re)Association Response is processed, the entire
exchange was transmitted encrypted over the air.
Add support to populate assoc_encrypted based on epp_peer flag.
Signed-off-by: Kavita Kavita <kavita.kavita@oss.qualcomm.com>
Link: https://patch.msgid.link/20260504123624.529218-3-kavita.kavita@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The per-STA bandwidth handling is completely confusing, given
the function names etc.
Move everything to sta_info.c and rename the functions to
accurately reflect what they return:
- ieee80211_sta_bw_capability()
- ieee80211_sta_current_bw() can return the appropriate
bandwidth in the desired direction (a new enum)
At any given time, the bandwidth with which we expect to receive
frames from a station may differ from the bandwidth with which
we may transmit frames to the station; this will happen either
during RX OMI negotiation, or for a long time if the station
used an HT Notify Channel Width frame. We also implement the
(VHT) Operating Mode Notification as an asymmetric setting, even
if the spec would seem to imply it could be symmetric.
Also rename the 'cur_max_bandwidth' value to 'op_mode_bw' which
matches the 'op_mode_nss', indicating more clearly what it _is_
rather than how it's _used_. It's not quite precise (NSS is)
since it's also HT chanwidth notification, but that seems OK.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260415144514.09ae71b74d5c.Ib59c2ac82e030559d1f7d462f06ba3488a090946@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the initial STA bandwidth is set during each
parsing of HT/VHT/... elements to the station capabilities,
multiple times, in a confusing way that's not very good in
the case of NAN stations either.
For now, keep the NULL chandef pointer and all that, but
clean up the initial handling of NSS/BW capabilities and
then apply the VHT operation mode on top of that. This
clarifies the code and the client code now also handles
the bandwidth change from Operating Mode Notification in
association response.
The HT code is completely unnecessary now, since the VHT
(soon to be renamed) function will be called and handles
HT as well.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260415144514.a4d88eb27a8d.Id7a316e75e7e3dce2023d987e6939060f5286378@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move ieee80211_sta_init_nss() from VHT code to station code,
and disentangle it from rate control. This way, it becomes
clearer when 'rx_nss' is set up.
While doing this, fix the client side code to set up
link_sta->op_mode_nss instead of link_sta->pub->rx_nss for
the opmode element in association response, and remove the
(now wrong) comment about handling that in the function.
type=cleanup
ticket=none
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-on: https://gerritwcs.ir.intel.com/c/iwlwifi-stack-dev/+/273695
Tested-by: iil_jenkins iil_jenkins <EC.GER.UNIX.IIL.JENKINS@INTEL.COM>
tested: iil_jenkins iil_jenkins <EC.GER.UNIX.IIL.JENKINS@INTEL.COM>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260415144514.bef3d07beeb6.I97fb93ccc1b366110ab23de58fcd73676cdd85d6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some Xfinity XB8 firmware advertises >1 spatial stream MCS indexes in
their basic HT-MCS set. On cards with lower spatial streams, the check
would fail, and we'd be stuck with no HT when in fact work fine with its
own supported rate. This change makes it so the check is only performed
in strict mode.
Fixes: 574faa0e93 ("wifi: mac80211: add HT and VHT basic set verification")
Signed-off-by: Rio Liu <rio@r26.me>
Link: https://patch.msgid.link/99Mv9QEceyPrQhSP52MtAVmz0_kWJmzqotJjD9YW6LGLqk-AZloAueUyHCURilFkuqOh6Ecv8i2KKdSE1ujP3AnbU5QEouVisT1w_V3xdfc=@r26.me
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current code does not support establishing MLO connections for
interfaces operating in 4-address AP_VLAN mode.
MLO bringup is blocked by sanity checks in cfg.c, iface.c, and mlme.c,
which prevent MLD initialization when use_4addr is enabled.
Remove these restrictions to allow 4-address AP_VLAN interfaces to
initialize as part of an MLD and successfully participate in MLO
connections. This patch series also adds the necessary changes to
support WDS operation in MLO, making these modifications valid.
Allow 4-address mode interfaces to:
- Proceed with MLD initialization during interface setup
- Add MLO links dynamically via ieee80211_add_intf_link()
- Establish associations with MLO-capable access points
- Support AP_VLAN interfaces with MLO parent APs
Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com>
Link: https://patch.msgid.link/20260326164723.553927-4-tamizh.raja@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently ieee80211_send_4addr_nullfunc() uses deflink.u.mgd.bssid
for addr1 and addr3 fields. In MLO configurations, deflink.u.mgd.bssid
represents link 0's BSSID and is not updated when link 0 is not an
assoc link. This causes 4-address NULL frames to be sent to the
wrong address, preventing WDS AP_VLAN interface creation on the peer AP.
To fix this use sdata->vif.cfg.ap_addr instead, which contains the AP's MLD
address populated during authentication/association and remains
valid regardless of which links are active.
This ensures 4-address NULL frames reach the correct AP, allowing
proper WDS operation over MLO connections.
Co-developed-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com>
Link: https://patch.msgid.link/20260326164723.553927-3-tamizh.raja@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A station which has a NSS ratio on the number of streams it is capable of
in 160MHz VHT operation is supposed to use the 'Extended NSS BW Support'
as defined by section '9.4.2.156.2 VHT Capabilities Information field'.
This was missing in ieee80211_determine_our_sta_mode() and so we would
wrongfully downgrade our bandwidth when connecting to an AP that supported
160MHz with messages such as:
[ 37.638346] wlan1: AP XX:XX:XX:XX:XX:XX changed bandwidth in assoc response, new used config is 5280.000 MHz, width 3 (5290.000/0 MHz)
Fixes: 310c8387c6 ("wifi: mac80211: clean up connection process")
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20260327100256.3101348-1-nico.escande@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Link ID Info field in the Reconfiguration Status Duple subfield of
the Reconfiguration Response frame only uses the lower four bits for the
link ID. The upper bits are reserved and should therefore be ignored.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260325215404.ab5ccf4bc62e.I9aef8f4fb6f1b06671bb6cf0e2bd4ec6e4c8bda4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In NAN, we have one set of (HT, VHT, HE) capabilities for all bands,
which means that we will need to process those capabilities without a
given sband.
To prepare for that, remove the sband argument from
ieee80211_ht_cap_ie_to_sta_ht_cap and ieee80211_he_cap_ie_to_sta_he_cap
and pass our own capabilities instead.
For ieee80211_vht_cap_ie_to_sta_vht_cap, make the sband argument
optional, since it is also used to check if there is at least one channel
that supports 80 MHz.
(Note that this check doesn't make much sense, but this can be handled in
a different patch.)
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260320141504.e42ef1f0eabb.If994d6346f00219437e22043e7bf2395b827b34a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_sta_free_link() only frees the link and doesn't
unhash it, so it can't be used here. Instead this needs
to use ieee80211_sta_remove_link(), which unhashes it. An
argument against it was that it also calls the driver and
that already happened, but calls to the driver removing a
link that's already removed are suppressed, so that's not
actually an issue. Use it to fix the hashtable.
Reported-and-tested-by: Jouni Malinen <j@w1.fi>
Fixes: 84674b03d8 ("wifi: mac80211: Remove deleted sta links in ieee80211_ml_reconf_work()")
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260318180622.9240067117e9.I45fb2b7f04d75e48d2f3e9c6650ef9f54a314f5b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When in strict mode, validate that the HE 6 GHz operation is
valid even when EHT operation is used instead. This checks
that APs are advertising correct information for HE clients,
without testing with such clients.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260303150832.74b934163b99.If4d1db3f39c37900cf0d0f4669cd5f8b677daaa0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The action code actually serves to identify the type of action
frame, so it really isn't part of the per-type structure. Pull
it out and have it in the general action frame format.
In theory, whether or not the action code is present in this
way is up to each category, but all categories that are defined
right now all have that value.
While at it, and since this change requires changing all users,
remove the 'u' and make it an anonymous union in this case, so
that all code using this changes.
Change IEEE80211_MIN_ACTION_SIZE to take an argument which says
how much of the frame is needed, e.g. category, action_code or
the specific frame type that's defined in the union. Again this
also ensures that all code is updated.
In some cases, fix bugs where the SKB length was checked after
having accessed beyond the checked length, in particular in FTM
code, e.g. ieee80211_is_ftm().
Link: https://patch.msgid.link/20260226183607.67e71846b59e.I9a24328e3ffcaae179466a935f1c3345029f9961@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the IEEE 802.1X authentication protocol in non-AP STA
mode, as specified in "IEEE P802.11bi/D4.0, 12.16.5".
IEEE 802.1X authentication involves multiple Authentication frame
exchanges, with the non-AP STA and AP alternating transaction
sequence numbers. The number of Authentication frame exchanges
depends on the EAP method in use. For IEEE 802.1X authentication,
process only Authentication frames with the expected transaction
sequence number.
For IEEE 802.1X Authentication, Table 9-71 specifies that the
Encapsulation Length field as specified in Clause 9.4.1.82 shall be
present in all IEEE 802.1X Authentication frames. Drop the frame in
the mac80211 if the Encapsulation Length field is missing.
After receiving the final Authentication frame with status code
WLAN_STATUS_8021X_AUTH_SUCCESS from the AP, mac80211 marks the state
as authenticated, as it indicates the EAP handshake has completed
successfully over the Authentication frames as specified in
Clause 12.16.5.
In the PMKSA caching case, only two Authentication frames are
exchanged if the AP identifies a valid PMKSA, then as specified
in Clause 12.16.8.3, the AP shall set the Status Code to
WLAN_STATUS_SUCCESS in the final Authentication frame and must not
include an encapsulated EAPOL PDU. This frame will be the final
Authentication frame from the AP when PMKSA caching is enabled,
and mac80211 marks the state as authenticated.
In case of authentication success or failure, forward the
Authentication frame to userspace(e.g. wpa_supplicant), and let
userspace validate the Authentication frame from the AP as per the
specification.
Signed-off-by: Kavita Kavita <kavita.kavita@oss.qualcomm.com>
Link: https://patch.msgid.link/20260226185553.1516290-5-kavita.kavita@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
link_id is taken from the ML Reconfiguration element (control & 0x000f),
so it can be 0..15. link_removal_timeout[] has IEEE80211_MLD_MAX_NUM_LINKS
(15) elements, so index 15 is out-of-bounds. Skip subelements with
link_id >= IEEE80211_MLD_MAX_NUM_LINKS to avoid a stack out-of-bounds
write.
Fixes: 8eb8dd2ffb ("wifi: mac80211: Support link removal using Reconfiguration ML element")
Reported-by: Ariel Silver <arielsilver77@gmail.com>
Signed-off-by: Ariel Silver <arielsilver77@gmail.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260220101129.1202657-1-Ariel.Silver@cybereason.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
- cfg80211/mac80211
- most of EPPKE/802.1X over auth frames support
- additional FTM capabilities
- split up drop reasons better, removing generic RX_DROP
- NAN cleanups/fixes
- ath11k:
- support for Channel Frequency Response measurement
- ath12k:
- support for the QCC2072 chipset
- iwlwifi:
- partial NAN support
- UNII-9 support
- some UHR/802.11bn FW APIs
- remove most of MLO/EHT from iwlmvm
(such devices use iwlmld)
- rtw89:
- preparations for RTL8922DE support
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEpeA8sTs3M8SN2hR410qiO8sPaAAFAml7PQcACgkQ10qiO8sP
aAAKiA/6AnyNxa0bX2VFsWYW6KJYnJBVNLlP2ghkV3uIWtJoZdXuQO+W8/cy9Cng
yrhfPzNfT+2hqmxasxI0tND3H3tW9CqcwX80J84eP9JCpYuPept9uGpSxPQoQl5J
Q2k9gX1NlO/SEa8/mOFDT4EmH0bQobxiN84kxSg6Riaazkj6ZjHVVm/3PgzNhxlA
v77m5thlhopzYxKn38qA19E9uHSLcY7XwkeYOZDf00Zhgot29lmDeHOf39IH+HvI
+a20q6tW59D7iX2IUyvLnWzFV1iEcJ6ONF/hYJ0r3TlfmX/NDWfOQxx87K8M1Tqh
sMa+FGrFdqloE1aYi1l+9m6Wu30pHmh7vhlgskPffPmvG+RkCEQCg1Me7eoFOzTB
81K2CMJ34Cp9se+QdiBtY5GpRPZIOlFmY6ZVyZIoEXHkn6r0R94e6dsMZuFcqjv1
y1dzv7BnraVMAQcqwkE9pQtq6LeJoHl2OUT2JzjbKhQhivMf9YubPBZ2QC1LZdMg
NYEX4XSeJ/etpUk1MZFnm5wOw545tMi3U2sAhpYWbE6UBPDrQBvYADqd3lq3DmWe
BdCDHTbqMnAJ3C0xFEKTYTmVF8IoFt6eOclFUPw4Uhq+YmU9x8wx1yBQbF9TjyKU
a/rDCahmryj5gwD0QFJKhdQjfKaQFVNZWZqaKaokM84+8kIdA2U=
=70Rs
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2026-01-29' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Another fairly large set of changes, notably:
- cfg80211/mac80211
- most of EPPKE/802.1X over auth frames support
- additional FTM capabilities
- split up drop reasons better, removing generic RX_DROP
- NAN cleanups/fixes
- ath11k:
- support for Channel Frequency Response measurement
- ath12k:
- support for the QCC2072 chipset
- iwlwifi:
- partial NAN support
- UNII-9 support
- some UHR/802.11bn FW APIs
- remove most of MLO/EHT from iwlmvm
(such devices use iwlmld)
- rtw89:
- preparations for RTL8922DE support
* tag 'wireless-next-2026-01-29' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (184 commits)
wifi: iwlegacy: add missing mutex protection in il4965_store_tx_power()
wifi: iwlegacy: add missing mutex protection in il3945_store_measurement()
wifi: mac80211: use u64_stats_t with u64_stats_sync properly
wifi: p54: Fix memory leak in p54_beacon_update()
wifi: cfg80211: treat deprecated INDOOR_SP_AP_OLD control value as LPI mode
wifi: rtw88: sdio: Migrate to use sdio specific shutdown function
wifi: rsi: sdio: Migrate to use sdio specific shutdown function
sdio: Provide a bustype shutdown function
wifi: nl80211/cfg80211: support operating as RSTA in PMSR FTM request
wifi: nl80211/cfg80211: add negotiated burst period to FTM result
wifi: nl80211/cfg80211: clarify periodic FTM parameters for non-EDCA based ranging
wifi: nl80211/cfg80211: add new FTM capabilities
wifi: iwlwifi: rename struct iwl_mcc_allowed_ap_type_cmd::offset_map
wifi: iwlwifi: mvm: Remove link_id from time_events
wifi: iwlwifi: mld: change cluster_id type to u8 array
wifi: iwlwifi: support V13 of iwl_lari_config_change_cmd
wifi: iwlwifi: split bios_value_u32 to separate the header
wifi: iwlwifi: uefi: cache the DSM functions
wifi: iwlwifi: acpi: cache the DSM functions
wifi: iwlwifi: mvm: Cleanup MLO code
...
====================
Link: https://patch.msgid.link/20260129110136.176980-39-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
