Add ath12k_dp_peer_fixup_peer_id() and call it from the
HTT_T2H_MSG_TYPE_MLO_RX_PEER_MAP handler. For devices where the
firmware allocates the MLD peer ID, this is the point at which
all data structures that were left with ATH12K_MLO_PEER_ID_PENDING
or ATH12K_MLO_PEER_ID_INVALID get their real ID:
- dp_peer->peer_id is updated and the dp_peer is published into
dp_hw->dp_peers[];
- every existing dp_link_peer in dp_peer->link_peers[] gets its
ml_id set to the same value;
- ahsta->ml_peer_id is updated to the same value so peer_assoc,
sta_state and cleanup paths see a consistent ID.
Devices with host_alloc_ml_id == true also receive the same HTT
event, but the firmware-reported ID always matches the
host-allocated one and everything has already been populated by
ath12k_dp_peer_create(); Skips the helper entirely on those devices.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221039
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720-ath12k-fw-allocated-ml-peer-id-v2-8-630632758a80@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
For chips with host_alloc_ml_id=true (QCN9274 etc.), the host allocates
the MLD peer ID up front; ath12k_dp_peer_create() publishes the dp_peer
into dp_hw->dp_peers[] using that ID immediately. WCN7850/QCC2072 does
not work that way: the firmware picks the ID and only tells the host
afterwards via HTT_T2H_MSG_TYPE_MLO_RX_PEER_MAP, so the publication has
to be delayed until the event arrives.
Introduce ATH12K_MLO_PEER_ID_PENDING (0xFFFE) as a sentinel for "is_mlo,
but ID not yet known". On the firmware-allocates path:
- ath12k_mac_op_sta_state(NOTEXIST->NONE) skips ath12k_peer_ml_alloc()
and stores PENDING in ahsta->ml_peer_id and dp_params.peer_id;
- ath12k_dp_peer_create() skips dp_peer registration until a real ID is
known;
- ath12k_peer_create() leaves peer->ml_id at INVALID so consumer sites
do not treat PENDING as a real ID;
- ath12k_peer_ml_free() and ath12k_mac_dp_peer_cleanup() skip the
dp_peers[] write and the free_ml_peer_id_map clear when
host_alloc_ml_id is false or the ID is still PENDING.
The HTT handler change that resolves the PENDING ID is added in a
follow-up patch.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720-ath12k-fw-allocated-ml-peer-id-v2-7-630632758a80@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_peer_assoc_h_mlo() unconditionally sets ml->peer_id_valid and copies
ahsta->ml_peer_id (with the ATH12K_PEER_ML_ID_VALID bookkeeping bit masked
off) into the WMI_PEER_ASSOC_CMDID ML params, which causes
ath12k_wmi_send_peer_assoc_cmd() to set ATH12K_WMI_FLAG_MLO_PEER_ID_VALID.
This needs to be gated on chips where the firmware allocates the MLD peer
ID:
- WCN7850/QCC2072 firmware always picks the ID itself and does not honor
a host-supplied one, so the value would be silently ignored anyway;
- QCC2072 firmware additionally crashes during MLO disconnect when
ATH12K_WMI_FLAG_MLO_PEER_ID_VALID was set in the preceding peer assoc,
so the bit must not be sent at all.
Branch on ah->host_alloc_ml_id:
- When true (QCN9274 etc.), behavior is unchanged: peer_id_valid is set
and the raw ahsta->ml_peer_id (without the VALID bit) is sent down.
- When false (WCN7850, QCC2072), peer_id_valid stays unset and
ml_peer_id is sent as 0. The firmware ignores both fields and reports
the ID it allocated through HTT_T2H_MSG_TYPE_MLO_RX_PEER_MAP.
The early-return on ahsta->ml_peer_id == ATH12K_MLO_PEER_ID_INVALID only
applies on the host-alloc path, since on the firmware-alloc path the value
is ATH12K_MLO_PEER_ID_PENDING here, not INVALID.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720-ath12k-fw-allocated-ml-peer-id-v2-6-630632758a80@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Different ath12k devices diverge on who allocates MLD peer id:
WCN7850/QCC2072 have the firmware allocate it and notify the host via
HTT_T2H_MSG_TYPE_MLO_RX_PEER_MAP event; While others let the host allocate
it and pass it down through WMI_PEER_ASSOC_CMDID with
ATH12K_WMI_FLAG_MLO_PEER_ID_VALID set.
Currently ath12k host allocates this ID and sends it to firmware by
default for all devices. This breaks WCN7850/QCC2072, because the host
maintained ID may be different from the firmware-allocated one.
Consequently data path may fail to find the dp peer and drop some received
packets. From user point of view, this results in bugs reported in [1] or
the 4-way handshake timeout issue.
Add host_alloc_ml_id flag to struct ath12k_hw_params (and a copy on struct
ath12k_hw for hot-path access) so subsequent patches can branch on it. Set
true for QCN9274/IPQ5332/IPQ5424, false for WCN7850/QCC2072. The flag will
be consumed by subsequent patches.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221039 # 1
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720-ath12k-fw-allocated-ml-peer-id-v2-5-630632758a80@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Firmware on chips that allocate the MLD peer ID itself (WCN7850 and
QCC2072) reports the assignment back to the host through
HTT_T2H_MSG_TYPE_MLO_RX_PEER_MAP. The message carries the chosen
MLD peer id, the MLD MAC address etc.
Add the message type, the on-the-wire struct, the field masks and a
handler that parses them out. The host-side state update (publishing the
dp peer into ath12k_dp_hw::dp_peers[], propagating the ID to
ath12k_dp_link_peer::ml_id and ath12k_sta::ml_peer_id) is added in a
follow-up patch;
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720-ath12k-fw-allocated-ml-peer-id-v2-4-630632758a80@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Several pieces of host bookkeeping for MLD peer IDs encode the
same fact in different ways:
- ath12k_sta::ml_peer_id stores the raw ID in [0, ATH12K_MAX_MLO_PEERS);
- ath12k_dp_peer::peer_id, ath12k_dp_link_peer::ml_id and the index used
on ath12k_dp_hw::dp_peers[] always carry the ATH12K_PEER_ML_ID_VALID
bit (BIT(13)) when the ID is real;
- WMI_MLO_PEER_ASSOC_PARAMS::ml_peer_id sent down to firmware is
raw, without the bookkeeping bit.
The mismatch leaks into call sites that have to remember to OR
the bit in (ath12k_peer_create(), ath12k_mac_op_sta_state()) or
remember not to (ath12k_peer_assoc_h_mlo()).
Make ath12k_sta::ml_peer_id carry the VALID bit when valid, the same
way ath12k_dp_peer::peer_id and ath12k_dp_link_peer::ml_id do:
- ath12k_peer_ml_alloc() OR-s the bit in once on the way out;
the internal bitmap stays raw [0, ATH12K_MAX_MLO_PEERS);
- ath12k_peer_create() and ath12k_mac_op_sta_state() drop the
explicit OR;
- ath12k_peer_assoc_h_mlo() masks the bit off when populating
the WMI ml_peer_id;
While there, introduce ath12k_peer_ml_free() to mirror
ath12k_peer_ml_alloc(), which helps avoid code duplication.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720-ath12k-fw-allocated-ml-peer-id-v2-3-630632758a80@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_bss_assoc(), ath12k_mac_station_assoc() and
ath12k_sta_rc_update_wk() all open-code the same sequence: reinit the
peer_assoc_done completion, send the peer assoc WMI command, then wait
for the firmware confirmation event. The reinit_completion() was buried
in ath12k_peer_assoc_prepare(), far from the wait_for_completion_timeout()
that consumes it, making the reinit/send/wait sequence hard to follow,
and the three open-coded copies are easy to get out of sync.
Move the sequence into a new helper ath12k_mac_peer_assoc() and call it
from all three sites. The reinit, send and wait now live together so the
completion's lifecycle is easy to read.
While at it, ath12k_sta_rc_update_wk() previously warned but still
waited the full timeout when the peer assoc command failed to send. Now
a send failure returns immediately and skips the pointless 1 second
wait, matching the other two callers.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720-ath12k-fw-allocated-ml-peer-id-v2-2-630632758a80@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_mac_dp_peer_cleanup() clears the ML peer ID slot on the
free_ml_peer_id_map bitmap by indexing it with dp_peer->peer_id. That is
wrong: dp_peer->peer_id for an MLO peer always carries the
ATH12K_PEER_ML_ID_VALID bit (BIT(13)), so clear_bit() is invoked with
index >= 0x2000, which is far outside the bitmap of ATH12K_MAX_MLO_PEERS
(256) bits and corrupts memory adjacent to ah->free_ml_peer_id_map. The
intended bitmap entry also never gets cleared, so subsequent
ath12k_peer_ml_alloc() calls eventually run out of IDs.
The ID without the VALID bit is what ath12k_peer_ml_alloc() returned and
is stored in ahsta->ml_peer_id. Use that instead.
While there, also reset ahsta->ml_peer_id to ATH12K_MLO_PEER_ID_INVALID so
the bitmap and ahsta->ml_peer_id stay in sync.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Fixes: ee16dcf573 ("wifi: ath12k: Define ath12k_dp_peer structure & APIs for create & delete")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720-ath12k-fw-allocated-ml-peer-id-v2-1-630632758a80@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The most significant change is to fix an ath12k regression which led
to low MLO RX throughput on WCN7850.
The remainder are an assortment of minor bug fixes spread across many
of the ath drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCalUE+AAKCRAsFbugiYzL
e41eAQD9fk23dZo0OlT3lWl4AO2VmUECeXFZ0SqCGMQ828t07wEA1NF/1Nzyf7xV
6S4gOVCX+lX8lm9AISx8lBcA6llb5g8=
=aNPp
-----END PGP SIGNATURE-----
Merge tag 'ath-current-20260713' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git update for v7.2-rc4
The most significant change is to fix an ath12k regression which led
to low MLO RX throughput on WCN7850.
The remainder are an assortment of minor bug fixes spread across many
of the ath drivers.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The failover continuation in carl9170_rx_stream() copies the full tlen
from the second USB transfer instead of capping at rx_failover_missing
bytes. When both transfers are near maximum size, the total exceeds the
65535-byte failover SKB, triggering skb_over_panic.
Limit the copy size to the missing byte count.
Fixes: a84fab3cbf ("carl9170: 802.11 rx/tx processing and usb backend")
Signed-off-by: Tristan Madani <tristan@talencesecurity.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=5c1ca6ccaa1215781cac
Link: https://patch.msgid.link/20260421134929.325662-4-tristmd@gmail.com
[Fix checkpatch CHECK:PARENTHESIS_ALIGNMENT]
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The bounds check in carl9170_tx_process_status() uses
`i > ((cmd->hdr.len / 2) + 1)` which is off by two, allowing
2 extra iterations past valid _tx_status entries when the firmware-
controlled hdr.ext exceeds hdr.len/2. Fix by using the correct
comparison `i >= (cmd->hdr.len / 2)`.
Fixes: a84fab3cbf ("carl9170: 802.11 rx/tx processing and usb backend")
Signed-off-by: Tristan Madani <tristan@talencesecurity.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=5c1ca6ccaa1215781cac
Link: https://patch.msgid.link/20260421134929.325662-3-tristmd@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When the firmware sends a command response with a length mismatch,
carl9170_cmd_callback() logs the mismatch and calls carl9170_restart()
but then falls through to memcpy(ar->readbuf, buffer + 4, len - 4).
Since len comes from the firmware and can exceed ar->readlen, this
copies more data than the readbuf was allocated for.
Bound the memcpy to min(len - 4, ar->readlen) so that the response
is still completed -- avoiding repeated restarts from queued garbage --
while preventing an overread past the response buffer.
Fixes: a84fab3cbf ("carl9170: 802.11 rx/tx processing and usb backend")
Signed-off-by: Tristan Madani <tristan@talencesecurity.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=5c1ca6ccaa1215781cac
Link: https://patch.msgid.link/20260421134929.325662-2-tristmd@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The firmware-controlled beacon_ie_len, assoc_req_len, and assoc_resp_len
fields in ath6kl_wmi_connect_event_rx() are not validated against the
buffer length. Their sum (up to 765) can exceed the actual WMI event
data, causing out-of-bounds reads during IE parsing and state corruption
of wmi->is_wmm_enabled.
Add a check that the total IE length fits within the buffer.
Fixes: bdcd817079 ("Add ath6kl cleaned up driver")
Signed-off-by: Tristan Madani <tristan@talencesecurity.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20260421135009.348084-3-tristmd@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The firmware-controlled num_msg field (u8, 0-255) drives the loop in
ath6kl_wmi_tx_complete_event_rx() without validation against the buffer
length. This allows out-of-bounds reads of up to 1020 bytes past the
WMI event buffer when the firmware sends an inflated num_msg.
Add a check that the buffer is large enough to hold the fixed struct
and the num_msg variable-length entries.
Fixes: bdcd817079 ("Add ath6kl cleaned up driver")
Signed-off-by: Tristan Madani <tristan@talencesecurity.com>
Link: https://patch.msgid.link/20260625232907.3620746-1-tristmd@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
aggr_recv_addba_req_evt() logs a debug message when the firmware-supplied
win_sz is outside [AGGR_WIN_SZ_MIN, AGGR_WIN_SZ_MAX] but does not
return. The out-of-range win_sz is then used in TID_WINDOW_SZ() to
compute a kzalloc size and stored in rxtid->hold_q_sz, leading to
zero-size or overflowed allocations and subsequent out-of-bounds access.
Clean up any previously active aggregation session for the TID first,
then return early when win_sz is out of the valid range, instead of
proceeding with a broken allocation size.
Fixes: bdcd817079 ("Add ath6kl cleaned up driver")
Cc: stable@vger.kernel.org
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Tristan Madani <tristan@talencesecurity.com>
Link: https://patch.msgid.link/20260702005020.708717-1-tristmd@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When unbinding the ath12k driver, kernel NULL pointer dereferences
occur in irq_work_sync() called from rhashtable_destroy().
Two hash tables are affected:
1. ath12k_link_sta hash table in ath12k_base
2. ath12k_dp_link_peer hash table in ath12k_dp
The issue happens because the destroy functions are called unconditionally
in cleanup paths, but the hash tables are only initialized late in their
respective init functions. If the device was never fully started or if the
init functions failed before initializing the hash tables, the pointers
will be NULL. The issues are always reproducible from a VM because the MSI
addressing initialization is failing.
Call trace for ath12k_link_sta_rhash_tbl_destroy:
RIP: irq_work_sync+0x1e/0x70
rhashtable_destroy+0x12/0x60
ath12k_link_sta_rhash_tbl_destroy+0x19/0x40 [ath12k]
ath12k_core_stop+0xe/0x80 [ath12k]
ath12k_core_hw_group_cleanup+0x6b/0xb0 [ath12k]
ath12k_pci_remove+0x60/0x110 [ath12k]
Call trace for ath12k_dp_link_peer_rhash_tbl_destroy:
RIP: irq_work_sync+0x1e/0x70
rhashtable_destroy+0x12/0x60
ath12k_dp_link_peer_rhash_tbl_destroy+0x29/0x50 [ath12k]
ath12k_dp_cmn_device_deinit+0x21/0x140 [ath12k]
ath12k_core_hw_group_cleanup+0x6b/0xb0 [ath12k]
ath12k_pci_remove+0x60/0x110 [ath12k]
Fix this by adding NULL checks before calling rhashtable_destroy() in
both destroy functions.
The NULL check approach was chosen because the rhashtable pointer
serves as the initialization state indicator. The init can fail at
various points, leaving some components uninitialized. Checking the
pointer directly is simpler than adding separate state flags that
would need synchronization.
Fixes: 57ccca4102 ("wifi: ath12k: Add hash table for ath12k_link_sta in ath12k_base")
Fixes: a88cf5f71a ("wifi: ath12k: Add hash table for ath12k_dp_link_peer")
Cc: stable@vger.kernel.org
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20260615112103.601982-1-jtornosm@redhat.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Commit [1] introduced a regression causing severely degraded MLO RX
throughput on WCN7850.
On WCN7850, there is only a single ar instance, but MLO uses two
link IDs. ath12k_dp_peer->hw_links[] is indexed using ar->hw_link_id,
which causes both MLO link IDs to be stored at the same index.
As a result, an incorrect link ID is assigned to MSDUs in
ath12k_dp_rx_deliver_msdu(), leading to severe MLO RX throughput loss.
Different chipsets identify the per-MSDU link differently:
- On QCN9274 / IPQ5332, the host owns multiple ar instances and the
per-MSDU hw_link_id from the RX descriptor maps cleanly through
dp_peer->hw_links[hw_link_id] to the IEEE link_id.
- On single-ar chipsets like WCN7850 / QCC2072, there is only one ar
instance for both MLO links, so dp_peer->hw_links[] has just one
valid slot and cannot be used to distinguish the two links. To
resolve the link, walk dp_peer->link_peers[] and match by
rxcb->peer_id, which on the link_peer side identifies the link
peer for the MSDU.
Add a new hw_op set_rx_link_id() so each chipset resolves the link
on the RX fast path using whatever signal it actually has, and let
the op itself decide whether to populate rx_status::link_valid and
rx_status::link_id:
QCN9274 / IPQ5332 : always derive link_id from
dp_peer->hw_links[rxcb->hw_link_id] and set
link_valid.
WCN7850 / QCC2072 : walk the link_peers[] of dp_peer to find the
link_peer whose peer_id matches rxcb->peer_id,
and set link_valid only when a match is found.
Otherwise leave link_valid clear so that
mac80211 can fall back to its own link
resolution path (via addr2 / deflink).
For WCN7850 / QCC2072, walking dp_peer->link_peers[] is bounded by
the number of links actually populated, so introduce a link_peers_map
bitmap (unsigned long) in struct ath12k_dp_peer that tracks populated
slots and use for_each_set_bit() to iterate. Non-MLO clients hit one
slot, current MLO clients hit two; the full ATH12K_NUM_MAX_LINKS
array is never scanned. The bitmap is maintained with WRITE_ONCE() on
the write side (under dp_hw->peer_lock) paired with READ_ONCE() on
both the lockless RX read side and the write-side RMW for KCSAN
correctness.
Also guard the dp_peer dereference in ath12k_mac_peer_cleanup_all()
with a NULL check, since peer->dp_peer can be NULL for self-peers or
peers not yet fully assigned, the pre-existing rcu_assign_pointer()
call there had the same latent issue.
This restores the correct link ID on WCN7850 without changing the
QCN9274 / IPQ5332 data path, which keeps its O(1) hw_links[]
indexing.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Fixes: 11157e0910 ("wifi: ath12k: Use ath12k_dp_peer in per packet Tx & Rx paths") # [1]
Signed-off-by: Yingying Tang <yingying.tang@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260610053315.2249912-1-yingying.tang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath12k_pci_soc_global_reset() tries to reset the device by writing to the
PCIE_SOC_GLOBAL_RESET register. But it doesn't do a read-back to ensure
that the write gets flushed to the device before the delay.
This may lead to the delay on the host to be insufficient, if the posted
write doesn't reach the device before the delay.
So add a read-back after writing to the PCIE_SOC_GLOBAL_RESET register and
before the delay.
Compile tested only.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.6-01243-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Reported-by: Alex Williamson <alex@shazbot.org>
Closes: https://lore.kernel.org/linux-pci/20260622160822.09350246@shazbot.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Raj Kumar Bhagat <raj.bhagat@oss.qualcomm.com>
Tested-by: Raj Kumar Bhagat <raj.bhagat@oss.qualcomm.com>
Link: https://patch.msgid.link/20260623141649.41087-2-manivannan.sadhasivam@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath11k_pci_soc_global_reset() tries to reset the device by writing to the
PCIE_SOC_GLOBAL_RESET register. But it doesn't do a read-back to ensure
that the write gets flushed to the device before the delay.
This may lead to the delay on the host to be insufficient, if the posted
write doesn't reach the device before the delay.
So add a read-back after writing to the PCIE_SOC_GLOBAL_RESET register and
before the delay.
Compile tested only.
Fixes: f3c603d412 ("ath11k: reset MHI during power down and power up")
Reported-by: Alex Williamson <alex@shazbot.org>
Closes: https://lore.kernel.org/linux-pci/20260622160822.09350246@shazbot.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Raj Kumar Bhagat <raj.bhagat@oss.qualcomm.com>
Link: https://patch.msgid.link/20260623141649.41087-1-manivannan.sadhasivam@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When the first entry in msdu_details has a zero buffer address,
the code accesses msdu_details[i - 1] with i == 0, causing a
buffer underflow.
Fix similarly to ath12k_wifi7_hal_rx_msdu_list_get() by adding
a separate check for i == 0 before the main condition to prevent
the out-of-bounds access.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Dmitry Morgun <d.morgun@ispras.ru>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260530114252.42615-1-d.morgun@ispras.ru
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When ath10k_htt_rx_pop_paddr32_list() or
ath10k_htt_rx_pop_paddr64_list() encounters an incomplete frame
(RX_ATTENTION_FLAGS_MSDU_DONE not set), it returns -EIO without
purging the skb list built up so far, leaking any skbs already
queued in the list.
Other early-exit paths within these same functions already call
__skb_queue_purge() before returning an error. Add it before the
-EIO return as well to be consistent and prevent the leak.
Tested-on: WCN3990 hw1.0 WLAN.HL.3.2.2.c10-00754-QCAHLSWMTPL-1
Fixes: c545070e40 ("ath10k: implement rx reorder support")
Fixes: 3b0b55b19d ("ath10k: Add support for 64 bit HTT in-order indication msg")
Signed-off-by: Manikanta Pubbisetty <manikanta.pubbisetty@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260623064355.1876743-1-manikanta.pubbisetty@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
of_get_child_by_name() returns a node pointer with refcount
incremented, but the error path when ath11k_ahb_setup_msa_resources()
fails does not release it. Add the missing of_node_put() to avoid
leaking the reference.
Cc: stable@vger.kernel.org
Fixes: 095cb94749 ("wifi: ath11k: allow missing memory-regions")
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260609092528.220547-1-vulab@iscas.ac.cn
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Replace the #include of <linux/mod_devicetable.h> by the more specific
<linux/device-id/*.h> where applicable. For most cases the include
can be dropped completely, only a few drivers need one or two headers
added.
Acked-by: Danilo Krummrich <dakr@kernel.org>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/1a3f2007c5c5dcf555c09a4035ce3ae8ef1b6c49.1782808461.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
In ATH11K_QMI_EVENT_FW_READY, ATH11K_FLAG_REGISTERED is set
unconditionally even when ath11k_core_qmi_firmware_ready() fails.
This leaves the driver in an inconsistent state where
initialization is considered complete although the firmware ready
handling did not finish successfully. During the subsequent SSR,
the driver enters the restart path based on this incorrect state
and dereferences uninitialized srng members, resulting in a NULL
pointer dereference.
Call trace:
ath11k_hal_srng_access_begin+0xc/0x60 [ath11k] (P)
ath11k_ce_cleanup_pipes+0x17c/0x180 [ath11k]
ath11k_core_restart+0x40/0x168 [ath11k]
Fix this by:
- skipping firmware_ready if ATH11K_FLAG_REGISTERED is already set
- setting ATH11K_FLAG_REGISTERED only when firmware_ready succeeds
- setting ATH11K_FLAG_QMI_FAIL and aborting the FW_READY handling
on error
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.2.0.c2-00204-QCAMSLSWPLZ-1
Fixes: 6fe62a8cec ("wifi: ath11k: Add cold boot calibration support on WCN6750")
Signed-off-by: Gaole Zhang <gaole.zhang@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260609090609.4041009-1-gaole.zhang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The aggr_reset_state() function uses timer_delete() (non-synchronous)
for the aggregation timer before proceeding to delete TID state and
before the structure is freed by callers like aggr_module_destroy().
If the timer callback (aggr_timeout) is executing when aggr_reset_state()
is called, the callback will continue to access aggr_conn fields like
rx_tid[] and stat[] which may be freed immediately after by
kfree(aggr_info->aggr_conn) in aggr_module_destroy().
Additionally, the timer callback can re-arm itself via mod_timer() while
aggr_reset_state() is running, creating a more complex race condition.
Use timer_delete_sync() instead to ensure any running timer callback
has completed before returning.
Fixes: bdcd817079 ("Add ath6kl cleaned up driver")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Hodges <git@danielhodges.dev>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20260206185207.30098-1-git@danielhodges.dev
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ath9k_hif_request_firmware() re-arms an asynchronous firmware load via
request_firmware_nowait(), passing hif_dev as the completion context, and
then still dereferences hif_dev:
dev_info(&hif_dev->udev->dev, "ath9k_htc: Firmware %s requested\n",
hif_dev->fw_name);
The re-armed callback ath9k_hif_usb_firmware_cb() runs on the "events"
workqueue and, when the firmware is missing, walks the retry chain into
ath9k_hif_usb_firmware_fail() -> complete_all(&hif_dev->fw_done). That
releases the wait_for_completion(&hif_dev->fw_done) in a concurrent
ath9k_hif_usb_disconnect(), which then kfree()s hif_dev. The trailing
dev_info() in the frame that re-armed the request can therefore read freed
memory (hif_dev->udev, the first field of struct hif_device_usb):
BUG: KASAN: slab-use-after-free in ath9k_hif_request_firmware
Read of size 8 ... by task kworker/...
ath9k_hif_request_firmware
ath9k_hif_usb_firmware_cb drivers/net/wireless/ath/ath9k/hif_usb.c:1247
request_firmware_work_func
Allocated by ...:
ath9k_hif_usb_probe drivers/net/wireless/ath/ath9k/hif_usb.c
Freed by ...:
ath9k_hif_usb_disconnect -> kfree drivers/net/wireless/ath/ath9k/hif_usb.c
The fw_done barrier only makes disconnect wait for the firmware chain to
*terminate*; it does not protect the outer ath9k_hif_request_firmware()
frame that re-armed the request and keeps touching hif_dev afterwards.
Drop the post-request dev_info(): it is the only use of hif_dev after the
async request is armed, and it is purely informational (the dev_err() on the
failure path runs only when request_firmware_nowait() did not arm a callback,
so hif_dev is still alive there).
This was first reported by syzbot as a single, non-reproduced crash that was
later auto-obsoleted, and was independently rediscovered by the reFuzz fuzzer,
which produced a C reproducer (USB-gadget connect/disconnect of an ath9k_htc
device whose firmware download fails). The vulnerable code is unchanged and
still present in v7.1-rc6, where the slab-use-after-free reproduces under KASAN
once the (sub-microsecond) race window is widened.
Fixes: e904cf6fe2 ("ath9k_htc: introduce support for different fw versions")
Reported-by: syzbot+50122cbc2874b1eb25b0@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=50122cbc2874b1eb25b0
Signed-off-by: Cheng Yongkang <teel4res@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20260605153210.20471-1-1020691186@qq.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
- Continued progress toward making alloc_workqueue() unbound by default:
more callers converted to WQ_PERCPU / system_percpu_wq / system_dfl_wq,
and new warnings for queues that use neither WQ_PERCPU nor WQ_UNBOUND
or the legacy system_wq / system_unbound_wq.
- Misc: drop the now-trivial apply_wqattrs_lock()/unlock() wrappers,
forbid the TEST_WORKQUEUE benchmark from being built-in, and fix a
spurious pointer level in the worker debug-dump path.
-----BEGIN PGP SIGNATURE-----
iIQEABYKACwWIQTfIjM1kS57o3GsC/uxYfJx3gVYGQUCajBxOQ4cdGpAa2VybmVs
Lm9yZwAKCRCxYfJx3gVYGeRdAP9/c9aAoUqVwvCjkPTnRQQ85XCzpc5T/aR7sjed
k7844AEAuxGMVPaMD9CNSN8AGOG8oseXjUUh500CRkQJj1Y65wQ=
=WkYL
-----END PGP SIGNATURE-----
Merge tag 'wq-for-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue updates from Tejun Heo:
- Continued progress toward making alloc_workqueue() unbound by
default: more callers converted to WQ_PERCPU / system_percpu_wq /
system_dfl_wq, and new warnings for queues that use neither WQ_PERCPU
nor WQ_UNBOUND or the legacy system_wq / system_unbound_wq.
- Misc: drop the now-trivial apply_wqattrs_lock()/unlock() wrappers,
forbid the TEST_WORKQUEUE benchmark from being built-in, and fix a
spurious pointer level in the worker debug-dump path.
* tag 'wq-for-7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
drm/bridge: anx7625: Add WQ_PERCPU add to alloc_workqueue
wifi: ath6kl: fix invalid workqueue flags in ath6kl_usb_create()
btrfs: Drop WQ_PERCPU from ordered_flags in btrfs_init_workqueues()
workqueue: Add warnings and ensure one among WQ_PERCPU or WQ_UNBOUND is present
workqueue: Add warnings and fallback if system_{unbound}_wq is used
workqueue: drop spurious '*' from print_worker_info() fn declaration
workqueue: forbid TEST_WORKQUEUE from being built-in
workqueue: drop apply_wqattrs_lock()/unlock() wrappers
umh: replace use of system_unbound_wq with system_dfl_wq
rapidio: rio: add WQ_PERCPU to alloc_workqueue users
media: ddbridge: add WQ_PERCPU to alloc_workqueue users
platform: cznic: turris-omnia-mcu: replace use of system_wq with system_percpu_wq
media: synopsys: hdmirx: replace use of system_unbound_wq with system_dfl_wq
virt: acrn: Add WQ_PERCPU to alloc_workqueue users
ath6kl_usb_create() currently creates ath6kl_wq with flags set to 0:
alloc_workqueue("ath6kl_wq", 0, 0)
This triggers a runtime warning in __alloc_workqueue() because the queue is
created with neither WQ_PERCPU nor WQ_UNBOUND set:
workqueue: ath6kl_wq is using neither WQ_PERCPU or WQ_UNBOUND.
Setting WQ_PERCPU.
Set WQ_PERCPU explicitly to match the actual execution model and remove the
warning during device probe. No functional change intended.
Fixes: 21c05ca88a ("workqueue: Add warnings and ensure one among WQ_PERCPU or WQ_UNBOUND is present")
Reported-by: syzbot+f80c62f371ba6a1e7d79@syzkaller.appspotmail.com
Link: https://lore.kernel.org/all/6a289c01.39669fcc.33b062.00aa.GAE@google.com/T/
Signed-off-by: wuyankun <wuyankun@uniontech.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When firmware reports NSS ratio support, SUPPORTS_VHT_EXT_NSS_BW is enabled in
ath12k. However, IEEE80211_VHT_EXT_NSS_BW_CAPABLE must also be set to make the
advertisement valid.
According to IEEE Std 802.11-2024, Subclause 9.4.2.156.3 (Supported VHT-MCS and
NSS Set subfields), the VHT Extended NSS BW Capable bit indicates whether a STA
is capable of interpreting the Extended NSS BW Support subfield of the VHT
capabilities information field. Advertising extended NSS BW support without
setting this capability bit is therefore invalid.
Without this change, mac80211 detects the inconsistency and logs:
ieee80211 phy0: copying sband (band 1) due to VHT EXT NSS BW flag
This indicates that mac80211 implicitly aligns IEEE80211_VHT_EXT_NSS_BW_CAPABLE
during ieee80211_register_hw(). Explicitly setting the bit in ath12k avoids this
fixup and ensures capabilities are advertised correctly by the driver.
This change follows the same approach as the existing ath11k fix.
https://lore.kernel.org/all/20211013073704.15888-1-wgong@codeaurora.org/
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Fixes: 18ab9d038f ("wifi: ath12k: add support for 160 MHz bandwidth")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260604095831.2674298-1-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
On WCN7850, after the following sequence:
1. load ath12k and connect to a non-MLO AP
2. disconnect and connect to an MLO AP
3. disconnect and reconnect to the non-MLO AP
the third connection always fails with a 4-Way handshake timeout. The
supplicant transmits message 2 of 4 four times in response to AP
retries of message 1, but the AP never sees any of them.
ath12k_dp_vdev_tx_attach() composes dp_link_vif->tcl_metadata using |=,
but dp_link_vif is embedded in struct ath12k_dp_vif and its slots are
reused across vif/peer teardown and setup. Since tcl_metadata is never
cleared on detach, vdev_id bits from a previous attach remain set when
the same link slot is reused with a different vdev_id. In this specific
issue, the same link slot is used for vdev_id 0, then vdev_id 1, then
vdev_id 0 again, the OR yields tcl_metadata == 0x9, which encodes
vdev_id 1 in the HTT_TCL_META_DATA_VDEV_ID field even though
ti.vdev_id is 0. Firmware then routes the EAPOL frame to the wrong
vdev and the AP never receives message 2.
Use plain assignment instead of |= so the field is fully recomputed
from the current arvif on every attach.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c7-00108-QCAHMTSWPL_V1.0_V2.0_SILICONZ_UPSTREAM-3
Fixes: af66c7640c ("wifi: ath12k: Refactor ath12k_vif structure")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260609-ath12k-fix-eapol-tcl-metadata-v1-1-d47e6f90d4ee@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Use a flexible array member to combine allocations. No need to have them
separate as they are always together.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20260521232020.261405-1-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The old platform data code that used this is gone and this serves no
purpose.
The modern way to disable bands is ieee80211-freq-limit, which is
already implemented.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20260521231806.261220-1-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
This array is fully initialized in the loop itself. No need to zero
initialize and then overwrite.
Remove static from the array. This was a holdover from when the array
was a static global variable. It no longer confers any benefit.
Also add a min() call to avoid the manual if/ternary operation.
Assisted-by: Codex:GPT-5.5
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20260517222136.1660347-1-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Clear ath9k DMA descriptors with explicit status word stores instead of
memset(). The descriptor rings are coherent DMA memory, which may be
mapped uncached on 32-bit powerpc. The optimized memset() path can use
dcbz there and trigger an alignment warning.
Use WRITE_ONCE() for the descriptor status words so the compiler keeps
the clears as ordinary stores instead of folding them back into bulk
memset(). This covers AR9003 TX status descriptors as well as the RX
status area cleared when setting up RX descriptors.
Assisted-by: Codex:GPT-5.5
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20260517042716.2218386-1-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
This follows the pattern with other USB Wifi drivers. There is nothing
special being done in the _init and _exit functions here. Simplifies and
saves some lines of code.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20260506234848.189840-1-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Fix three spelling mistakes in the DMA Transfer Engine (DXE)
description comment at the top of dxe.c.
No functional change.
Signed-off-by: Stepan Ionichev <sozdayvek@gmail.com>
Link: https://patch.msgid.link/20260503165832.1675-1-sozdayvek@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The firmware response length is only checked against sizeof(*rsp) (20
bytes), but when candidate_cnt >= 1, a 22-byte candidate struct is read
at buf + 20 without verifying the response contains it. This causes an
out-of-bounds read of stale heap data, corrupting the BA session state.
Add validation that the response includes the candidate data.
Fixes: 16be1ac559 ("wcn36xx: Parse trigger_ba response properly")
Signed-off-by: Tristan Madani <tristan@talencesecurity.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20260421135018.352774-4-tristmd@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The firmware-controlled rsp->count field is used as the loop bound for
indexing into the flexible rsp->regs[] array without validation against
the message length. A count exceeding the actual data causes out-of-
bounds reads from the heap-allocated message buffer.
Add a check that count fits within the received message.
Fixes: 43efa3c0f2 ("wcn36xx: Implement print_reg indication")
Signed-off-by: Tristan Madani <tristan@talencesecurity.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20260421135018.352774-3-tristmd@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The firmware response dispatcher copies all synchronous HAL responses
into the 4096-byte hal_buf without validating the response length. A
response exceeding WCN36XX_HAL_BUF_SIZE causes a heap buffer overflow
with firmware-controlled content.
Add a bounds check on the response length.
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Tristan Madani <tristan@talencesecurity.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Link: https://patch.msgid.link/20260421135018.352774-2-tristmd@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In ath12k, add driver support for WDS mode.
In ath11k and ath12k, a number of cleanups and minor bug fixes.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCah7oAwAKCRAsFbugiYzL
e4FRAQDP7XeGi3lDh02TlRthSY1z1fw8dTnUoHrok3MozxwGrQEAztgSQg1wjERh
PAKcUibVH/ebQf5MHziPl+/ZR24RCwM=
=iZG5
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20260602' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git patches for v7.2 (PR #3)
In ath12k, add driver support for WDS mode.
In ath11k and ath12k, a number of cleanups and minor bug fixes.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove WIPHY_FLAG_SUPPORTS_5_10_MHZ and 5/10 MHz channel
width support. We contemplated this back in early 2023
and didn't do it yet, but nobody stepped up to maintain
it.
It's already _mostly_ dead code since it can really only
be used for AP and maybe IBSS and monitor, but not on a
client since there's no way to scan (and hasn't been in
a very long time, if ever), so the only thing that ever
could really happen with it was run syzbot and trip over
assumptions in the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20260529084502.080c5885f0b7.I77cc94485b523c3c006005b9233db13cd4e077b3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Whenever hardware receives 4-address EAPOL frames from an unauthorized
station it is routed through WBM/RXDMA error path with the
HAL_REO_ENTR_RING_RXDMA_ECODE_UNAUTH_WDS_ERR error code. But, the
current driver does not handle the 4-address EAPOL frames
in the WBM error path. As a result, these frames are dropped,
causing authentication failures and connectivity issues for 4-address
stations.
Add support to correctly process these frames and forward them to mac80211
for proper handling. This prevents the loss of 4-address EAPOL frames and
ensures reliable connectivity for WDS/4-address clients.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.6-01243-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260525110942.2890212-7-tamizh.raja@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
mac80211 currently relies on receiving 4-address frames from connected
stations to trigger AP_VLAN interface creation. However, when ethernet
encapsulation offload is enabled, mac80211 only receives 802.3 frames
and cannot differentiate between 3-address and 4-address formats,
preventing AP_VLAN creation.
Enable mac80211 to detect 4-address traffic by converting 802.3 frames
back into 802.11 frames in the driver and setting the FROM_DS and TO_DS
bits using the RX_MSDU_END_INFO5_FROM_DS and RX_MSDU_END_INFO5_TO_DS
fields. This restores 4-address frame visibility to mac80211 and allows
it to trigger AP_VLAN interface creation.
Skip this frame conversion once the AP_VLAN interface is created and the
station is attached to it.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.6-01243-QCAHKSWPL_SILICONZ-1
Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260525110942.2890212-6-tamizh.raja@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the firmware processes all NULL frames internally and
does not forward them to the host. As a result, the host never
receives 4-address NULL frames sent by a 4-address station.
These 4-address NULL frames are sent by the station to indicate
to the AP that it is operating in 4-address mode.
Enable WMI_RSRC_CFG_FLAGS2_WDS_NULL_FRAME_SUPPORT flag during WMI
initialization after verifying the WMI_SERVICE_WDS_NULL_FRAME_SUPPORT
service capability. This enables the firmware to forward all NULL frames
to the host. Add host-side handling to parse 4-address NULL frames and
forward them to mac80211 to support proper AP_VLAN interface creation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.6-01243-QCAHKSWPL_SILICONZ-1
Co-developed-by: Sarika Sharma <sarika.sharma@oss.qualcomm.com>
Signed-off-by: Sarika Sharma <sarika.sharma@oss.qualcomm.com>
Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260525110942.2890212-5-tamizh.raja@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently driver does not enable the hardware/firmware support for handling
4-address multicast frames in the Tx/Rx path when 8023_ENCAP_OFFLOAD is
enabled. Add the required support to ensure correct processing of multicast
traffic in 4-address mode.
Enable this functionality by setting the WMI_VDEV_PARAM_AP_ENABLE_NAWDS
vdev parameter when the 8023_ENCAP_OFFLOAD feature is active. Override
peer metadata values for 4-address multicast packet transmission by using
the station's ast_hash and ast_idx instead of vdev-level metadata,
and set HAL_TCL_DATA_CMD_INFO4_IDX_LOOKUP_OVERRIDE to indicate this
override.
Suppress firmware peer-map events for 4-address frames by setting the
WMI_RSRC_CFG_FLAGS2_FW_AST_INDICATION_DISABLE flag during WMI
initialization. This prevents inconsistencies in the host's peer list.
Add the IEEE80211_OFFLOAD_ENCAP_4ADDR VIF offload flag to notify mac80211
that 4-address Ethernet encapsulation offload is supported.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.6-01243-QCAHKSWPL_SILICONZ-1
Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260525110942.2890212-4-tamizh.raja@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
