In rtase_start_xmit(), when the head buffer DMA mapping fails after
rtase_xmit_frags() has mapped all fragments, the error path clears
the fragment descriptors with rtase_tx_clear_range(), which frees
the skb through the last-frag slot and accounts tx_dropped. Control
then falls through to the common error label, which frees the same
skb a second time and counts it again.
Return right after clearing the fragments when the skb owns frags;
the no-frag case still drops through and frees the head skb once.
Fixes: d6e882b89f ("rtase: Implement .ndo_start_xmit function")
Signed-off-by: Yun Lu <luyun@kylinos.cn>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20260721023836.6691-1-luyun_611@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hardware performs packet parsing before packet transmission.
Parsing incomplete IPv4, IPv6, TCP, or UDP headers may trigger a TX
hang because the hardware parser expects additional protocol header
data that is not present in the packet.
The hardware performs additional PTP parsing on UDP packets identified
by destination ports 319/320 at the expected UDP destination port
offset.
If such a packet has transport data smaller than RTASE_MIN_PAD_LEN,
the hardware parser expects additional packet data and may trigger a
TX hang.
To avoid these hardware issues, the driver applies the following
workarounds.
Drop malformed packets that may trigger this hardware issue before
transmission.
For IPv4 non-initial fragments, the hardware does not check the
fragment offset before parsing the expected transport header location.
As a result, these packets are still subject to transport header
parsing even though they do not contain a transport header. If the
transport data is shorter than the minimum transport header required
by the hardware parser, pad the transport data to the minimum
transport header length required by the hardware parser. Packets that
also match the hardware PTP parsing conditions continue to follow the
corresponding workaround.
For IPv6 fragmented packets, neither of the above hardware issues
occurs because the hardware only continues packet parsing when the
IPv6 Base Header Next Header field directly indicates UDP. Packets
carrying a Fragment Header do not continue through the subsequent
packet parsing stages.
For packets identified for hardware PTP parsing, pad the transport
data so it reaches RTASE_MIN_PAD_LEN before transmission.
Fixes: d6e882b89f ("rtase: Implement .ndo_start_xmit function")
Cc: stable@vger.kernel.org
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260709103456.83789-1-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The .ndo_get_stats64 callback must not sleep because it can be
called when reading /proc/net/dev.
rtase_get_stats64() calls rtase_dump_tally_counter(), which polls
the tally counter dump bit with read_poll_timeout(). This may
sleep while waiting for the hardware counter dump to complete.
Use read_poll_timeout_atomic() instead to avoid sleeping in the
get_stats64() path.
Fixes: 0796004899 ("rtase: Implement net_device_ops")
Cc: stable@vger.kernel.org
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20260603061816.31356-1-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rtase_tx_clear() clears the TX ring and resets the ring indexes.
However, the TX queue state and BQL accounting are not reset at
the same time.
This may leave __QUEUE_STATE_STACK_XOFF asserted after
rtase_sw_reset(), preventing new TX packets from being scheduled.
Reset the TX subqueue when clearing the TX ring so the TX queue
state and BQL accounting are restored together.
Fixes: 5a2a2f1524 ("rtase: Implement the rtase_down function")
Cc: stable@vger.kernel.org
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://patch.msgid.link/20260602114659.12335-1-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
... and PCI device helpers.
The various struct pci_device_id arrays were initialized mostly by one
the PCI_DEVICE macros and then list expressions. The latter isn't easily
readable if you're not into PCI. Using named initializers is more
explicit and thus easier to parse.
Also use PCI_DEVICE* helper macros to assign .vendor, .device,
.subvendor and .subdevice where appropriate and skip explicit
assignments of 0 (which the compiler takes care of).
The secret plan is to make struct pci_device_id::driver_data an
anonymous union (similar to
https://lore.kernel.org/all/cover.1776579304.git.u.kleine-koenig@baylibre.com/)
and that requires named initializers. But it's also a nice cleanup on
its own.
This change doesn't introduce changes to the compiled pci_device_id
arrays. Tested on x86 and arm64.
Reviewed-by: Jijie Shao <shaojijie@huawei.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Forwarded: id:76da4f44d48bdde84580963862bf9616bee5c9e9.1778149923.git.u.kleine-koenig@baylibre.com (v2)
Reviewed-by: Michael Grzeschik <mgr@kernel.org>
Link: https://patch.msgid.link/20260511090023.1634387-6-u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hardware has two sets of registers controlling TX/RX flow control.
The effective flow control state is determined by the logical OR of
these two sets of bits.
RTASE_FORCE_TXFLOW_EN and RTASE_FORCE_RXFLOW_EN in RTASE_CPLUS_CMD are
the bits used by the driver to control TX/RX flow control according to
the ethtool pause configuration.
RTASE_TXFLOW_EN and RTASE_RXFLOW_EN in RTASE_GPHY_STD_00 are another
set of TX/RX flow control enable bits. Clear them by default so they do
not keep flow control enabled independently of the driver setting.
With the RTASE_GPHY_STD_00 bits cleared, the effective flow control
state is controlled through RTASE_CPLUS_CMD, so the ethtool setting can
take effect correctly.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260505064121.31286-1-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support for chip RTL8125cp. Its XID is 0x708. We apply
different configuration and firmware for RTL8125cp.
Signed-off-by: Javen Xu <javen_xu@realsil.com.cn>
Link: https://patch.msgid.link/20260303094611.450-1-javen_xu@realsil.com.cn
[pabeni@redhat.com: changelog cleanup]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
The module version is useless, and the only thing these drivers' init
routines did besides pci_register_driver was to print the driver name
and/or version.
Acked-by: Francois Romieu <romieu@fr.zoreil.com> (epic100)
Reviewed-by: Simon Horman <horms@kernel.org> (epic100, sis900)
Reviewed-by: Sai Krishna <saikrishnag@marvell.com> (epic100)
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Link: https://patch.msgid.link/20260131022441.56274-1-enelsonmoore@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Minor simplification of the code by removing the optional size argument.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/d560ec66-848e-4290-818a-ce28f39de493@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The bits in register TxConfig used for chip identification aren't
sufficient for the number of upcoming chip versions. Therefore a register
is added with extended chip version information, for compatibility
purposes it's called TX_CONFIG_V2. First chip to use the extended chip
identification is RTL9151AS.
Signed-off-by: Javen Xu <javen_xu@realsil.com.cn>
[hkallweit1@gmail.com: add support for extended XID where XID is printed]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/a3525b74-a1aa-43f6-8413-56615f6fa795@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver is old and almost certainly entirely unused. The two other
parallel port Ethernet drivers (de600/de620) were removed by Paul
Gortmaker in commit 168e06ae26 ("drivers/net: delete old parallel
port de600/de620 drivers"), but this driver remained. Drop it - Paul's
reasoning applies here as well. To quote him:
"The parallel port is largely replaced by USB [...] Let us not pretend
that anyone cares about these drivers anymore, or worse - pretend that
anyone is using them on a modern kernel."
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Acked-by: Daniel Palmer <daniel@thingy.jp>
Link: https://patch.msgid.link/20260121084532.60606-1-enelsonmoore@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This adds DASH support for chip RTL8127AP. Its mac version is
RTL_GIGA_MAC_VER_80 and revision id is 0x04. DASH is a standard for
remote management of network device, allowing out-of-band control.
Signed-off-by: Javen Xu <javen_xu@realsil.com.cn>
Link: https://patch.msgid.link/20260109070415.1115-2-javen_xu@realsil.com.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
RTL8127ATF supports a SFP+ port for fiber modules (10GBASE-SR/LR/ER/ZR and
DAC). The list of supported modes was provided by Realtek. According to the
r8127 vendor driver also 1G modules are supported, but this needs some more
complexity in the driver, and only 10G mode has been tested so far.
Therefore mainline support will be limited to 10G for now.
The SFP port signals are hidden in the chip IP and driven by firmware.
Therefore mainline SFP support can't be used here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Link: https://patch.msgid.link/5c390273-458f-4d92-896b-3d85f2998d7d@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Wake-on-Lan does currently not work for r8169 in DASH mode, e.g. the
ASUS Pro WS X570-ACE with RTL8168fp/RTL8117.
Fix by not returning early in rtl_prepare_power_down when dash_enabled.
While this fixes WoL, it still kills the OOB RTL8117 remote management
BMC connection. Fix by not calling rtl8168_driver_stop if WoL is enabled.
Fixes: 065c27c184 ("r8169: phy power ops")
Signed-off-by: René Rebe <rene@exactco.de>
Cc: stable@vger.kernel.org
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20251202.194137.1647877804487085954.rene@exactco.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This adds DASH support for chip RTL8127AP. Its mac version is
RTL_GIGA_MAC_VER_80. DASH is a standard for remote management of network
device, allowing out-of-band control.
Signed-off-by: Javen Xu <javen_xu@realsil.com.cn>
Link: https://patch.msgid.link/20251126055950.2050-1-javen_xu@realsil.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Let phydev->enable_tx_lpi control whether MAC enables TX LPI, instead of
enabling it unconditionally. This way TX LPI is disabled if e.g. link
partner doesn't support EEE. This helps to avoid potential issues like
link flaps.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/91bcb837-3fab-4b4e-b495-038df0932e44@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There have been reports that RTL8127 hangs on suspend and shutdown,
partially disappearing from lspci until power-cycling.
According to Realtek disabling PLL's when switching to D3 should be
avoided on that chip version. Fix this by aligning disabling PLL's
with the vendor drivers, what in addition results in PLL's not being
disabled when switching to D3hot on other chip versions.
Fixes: f24f7b2f3a ("r8169: add support for RTL8127A")
Tested-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/d7faae7e-66bc-404a-a432-3a496600575f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This adds support for chip RTL9151A. Its XID is 0x68b. It is bascially
basd on the one with XID 0x688, but with different firmware file.
Signed-off-by: Javen Xu <javen_xu@realsil.com.cn>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20251121090104.3753-1-javen_xu@realsil.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It was reported that on a card with RTL8127AF (SFP + DAC) link-up isn't
detected. Realtek hides the SFP behind the internal PHY, which isn't
behaving fully compliance with clause 22 any longer in fiber mode.
Due to not having access to chip documentation there isn't much I can
do for now. Instead of silently failing to detect link-up in fiber mode,
inform the user that fiber mode isn't support and bail out.
The logic to detect fiber mode is borrowed from Realtek's r8127 driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/fab6605a-54e2-4f54-b194-11c2b9caaaa9@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This adds support for chip RTL8125K. Its XID is 0x68a. It is basically
based on the one with XID 0x688, but with different firmware file.
Signed-off-by: javen <javen_xu@realsil.com.cn>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20251111092851.3371-1-javen_xu@realsil.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's a good chance that more chip versions suffer from the same
hw issue. So let's reconfigure rx unconditionally before the chip reset
when resuming. This shouldn't have any side effect on unaffected chip
versions.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/a5c2e2d2-226f-4896-b8f6-45e2d91f0e24@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After resume from S4 (hibernate), RTL8168H/RTL8111H truncates incoming
packets. Packet captures show messages like "IP truncated-ip - 146 bytes
missing!".
The issue is caused by RxConfig not being properly re-initialized after
resume. Re-initializing the RxConfig register before the chip
re-initialization sequence avoids the truncation and restores correct
packet reception.
This follows the same pattern as commit ef9da46dde ("r8169: fix data
corruption issue on RTL8402").
Fixes: 6e1d0b8988 ("r8169:add support for RTL8168H and RTL8107E")
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20251009122549.3955845-1-lilinmao@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
EEE speed down means speed down MAC MCU clock. It is not from spec.
It is kind of Realtek specific power saving feature. But enable it
may cause some issues, like packet drop or interrupt loss. Different
hardware may have different issues.
EEE speed down ratio (mac ocp 0xe056[7:4]) is used to set EEE speed
down rate. The larger this value is, the more power can save. But it
actually save less power then we expected. And, as mentioned above,
will impact compatibility. So set it to 1 (mac ocp 0xe056[7:4] = 0)
, which means not to speed down, to improve compatibility.
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20250918023425.3463-1-hau@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ASPM isn't disabled if system vendor flags it as safe. Log this,
in order to know whom to blame if a user complains about ASPM
issues on such a system.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/a532b46b-ef68-4d68-a129-35ff0ee35150@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When 8139too is probing and 8139TOO_PIO=y it will call pci_iomap_range()
and from there __pci_ioport_map() for the PCI IO space.
If HAS_IOPORT_MAP=n and NO_GENERIC_PCI_IOPORT_MAP=n, like it is on my
m68k config, __pci_ioport_map() becomes NULL, pci_iomap_range() will
always fail and the driver will complain it couldn't map the PIO space
and return an error.
NO_IOPORT_MAP seems to cover the case where what 8139too is trying
to do cannot ever work so make 8139TOO_PIO depend on being it false
and avoid creating an unusable driver.
Signed-off-by: Daniel Palmer <daniel@thingy.jp>
Link: https://patch.msgid.link/20250907064349.3427600-1-daniel@thingy.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The CRC error bit is located at bit 17 in the Rx descriptor, but the
driver was incorrectly using bit 16. Fix it.
Fixes: a36e9f5cfe ("rtase: Add support for a pci table in this module")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Link: https://patch.msgid.link/20250813071631.7566-1-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link queues to NAPI instances with netif_queue_set_napi. This
information can be queried with the netdev-genl API.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Reviewed-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20250616032226.7318-3-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link IRQs to NAPI instances with netif_napi_set_irq. This
information can be queried with the netdev-genl API.
Also add support for persistent NAPI configuration using
netif_napi_add_config().
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Reviewed-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20250616032226.7318-2-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
Use min() instead of min_t() to avoid the possibility of casting to the
wrong type.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250520042031.9297-1-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This adds support for 10Gbs chip RTL8127A.
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20250515095303.3138-1-hau@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the following compile error reported by the kernel test
robot by modifying the condition used to detect overflow in
rtase_calc_time_mitigation.
In file included from include/linux/mdio.h:10:0,
from drivers/net/ethernet/realtek/rtase/rtase_main.c:58:
In function 'u16_encode_bits',
inlined from 'rtase_calc_time_mitigation.constprop' at drivers/net/
ethernet/realtek/rtase/rtase_main.c:1915:13,
inlined from 'rtase_init_software_variable.isra.41' at drivers/net/
ethernet/realtek/rtase/rtase_main.c:1961:13,
inlined from 'rtase_init_one' at drivers/net/ethernet/realtek/
rtase/rtase_main.c:2111:2:
>> include/linux/bitfield.h:178:3: error: call to '__field_overflow'
declared with attribute error: value doesn't fit into mask
__field_overflow(); \
^~~~~~~~~~~~~~~~~~
include/linux/bitfield.h:198:2: note: in expansion of macro
'____MAKE_OP'
____MAKE_OP(u##size,u##size,,)
^~~~~~~~~~~
include/linux/bitfield.h:200:1: note: in expansion of macro
'__MAKE_OP'
__MAKE_OP(16)
^~~~~~~~~
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202503182158.nkAlbJWX-lkp@intel.com/
Fixes: a36e9f5cfe ("rtase: Add support for a pci table in this module")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250424040444.5530-1-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Handling of both chip versions is the same, only difference is
the firmware. So we can merge handling of both chip versions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/ae866b71-c904-434e-befb-848c831e33ff@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Handling of both chip versions is the same, only difference is
the firmware. So we can merge handling of both chip versions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/0baad123-c679-4154-923f-fdc12783e900@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Handling of both chip versions is the same, only difference is
the firmware. So we can merge handling of both chip versions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/97d7ae79-d021-4b6b-b424-89e5e305b029@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use pci_prepare_to_sleep() like PCI core does in pci_pm_suspend_noirq.
This aligns setting a low-power mode during shutdown with the handling
of the transition to system suspend. Also the transition to runtime
suspend uses pci_target_state() instead of setting D3hot unconditionally.
Note: pci_prepare_to_sleep() uses device_may_wakeup() to check whether
device may generate wakeup events. So we don't lose anything by
not passing tp->saved_wolopts any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/f573fdbd-ba6d-41c1-b68f-311d3c88db2c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for ndo_setup_tc to enable CBS offload functionality as
part of traffic control configuration for network devices, where CBS
is applied from the CPU to the switch. More specifically, CBS is
applied at the GMAC in the topmost architecture diagram.
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250416115757.28156-1-justinlai0215@realtek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a new mac_version enum value RTL_GIGA_MAC_VER_LAST. Benefit is that
when adding support for a new chip version we have to touch less code,
except something changes fundamentally.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/06991f47-2aec-4aa2-8918-2c6e79332303@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor chip version detection and merge both configuration tables.
Apart from reducing the code by a third, this paves the way for
merging chip version handling if only difference is the firmware.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/1fea533a-dd5a-4198-a9e2-895e11083947@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
