If all available channel resources are used for NAN channels, and one of
them is shared with another interface, and that interface needs to move
to a different channel (for example STA interface that needs to do a
channel or a link switch), then the driver can evacuate one of the NAN
channels (i.e. detach it from its channel resource and announce to the
peers that this channel is ULWed). In that case, the driver needs to
notify user space about the channel evacuation, so the user space can
adjust the local schedule accordingly.
Add a notification to let userspace know about it.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260219114327.d5bebfd5ff73.Iaaf5ef17e1ab7a38c19d60558e68fcf517e2b400@changeid
Link: https://patch.msgid.link/20260318123926.206536-11-miriam.rachel.korenblit@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an NL80211 command to configure the NAN schedule of a NAN peer.
Such a schedule contains a list of NAN channels, and a mapping from each
time slots to the corresponding channel (or unscheduled).
Also contains more information about the schedule, such as sequence ID
and map ID.
Not all of the restrictions are validated in this patch. In particular,
comparison of two maps of the same peer requires storing/retrieving each
map of each peer, only for validation.
Therefore, it is the responsibilty of the driver to check that.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260219114327.5b13fa5af4f6.If0e214ff5b52c9666e985fefa3f7be0ad14d93fb@changeid
Link: https://patch.msgid.link/20260318123926.206536-7-miriam.rachel.korenblit@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an nl80211 API to allow user space to configure the local NAN
schedule.
The local schedule consists of a list of channel definitions and a schedule
map, in which each element covers a time slot and indicates on what
channel the device should be in that time slot.
Channels can be added to schedule even without being scheduled, for
reservation purposes.
A schedule can be configured either immedietally or be deferred, in case
there are already connected peers.
When the deferred flag is set, the command is a request from the device
to perform an announced schedule update: send the updated NAN
Availability - as set in this command - to the peers, and do the
actual switch to the new schedule on the right time (i.e. at the end of
the slot after the slot in which the update was sent to the peers).
In addition, a notification will be sent to indicate a deferred update
completion.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260219114327.ecca178a2de0.Ic977ab08b4ed5cf9b849e55d3a59b01ad3fbd08e@changeid
Link: https://patch.msgid.link/20260318123926.206536-2-miriam.rachel.korenblit@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently key installation is only supported for netdev. For NAN,
support most key operations (except setting default data key) on
wdevs instead of netdevs, and adjust all the APIs and tracing to
match.
Since nothing currently sets NL80211_EXT_FEATURE_SECURE_NAN, this
doesn't change anything (P2P Device already isn't allowed.)
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260107150057.69a0cfad95fa.I00efdf3b2c11efab82ef6ece9f393382bcf33ba8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, a station can only be added to a netdev interface,
mainly because there was no need for a station of a non-netdev
interface.
But for NAN, we will have stations that belong to the NL80211_IFTYPE_NAN
interface.
Prepare for adding/changing/deleting a station that belongs to a non-netdev
interface. This doesn't actually allow such stations - this will be done
in a different patch.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260219114327.65c9cc96f814.Ic02066b88bb8ad6b21e15cbea8d720280008c83b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When any incumbent signal is detected by an AP/mesh interface operating
in 6 GHz band, FCC mandates the AP/mesh to vacate the channels affected
by it [1].
Add a new API cfg80211_incumbent_signal_notify() that can be used
by mac80211 or drivers to notify the higher layers about the signal
interference event with the interference bitmap in which each bit
denotes the affected 20 MHz in the operating channel.
Add support for the new nl80211 event and nl80211 attribute as well to
notify userspace on the details about the interference event. Userspace is
expected to process it and take further action - vacate the channel, or
reduce the bandwidth.
[1] - https://apps.fcc.gov/kdb/GetAttachment.html?id=nXQiRC%2B4mfiA54Zha%2BrW4Q%3D%3D&desc=987594%20D02%20U-NII%206%20GHz%20EMC%20Measurement%20v03&tracking_number=277034
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Signed-off-by: Amith A <amith.a@oss.qualcomm.com>
Link: https://patch.msgid.link/20260216032027.2310956-2-amith.a@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, whenever cfg80211_stop_iface() is called, the entire iface
is stopped. However, there could be a need in AP/P2P_GO mode, where
one would like to stop a single link in MLO operation instead of the
whole MLD interface.
Hence, introduce cfg80211_stop_link() to allow drivers to tear down
only a specified AP/P2P_GO link during MLO operation. Passing -1
preserves the existing behavior of stopping the whole interface. Make
cfg80211_stop_iface() call this function by passing -1 to keep the
default behavior the same, that is, to stop all links and use
cfg80211_stop_link() with the desired link_id for AP/P2P_GO mode, to
stop only that link.
This brings no behavioral change for single-link/non-MLO interfaces,
and enables drivers to stop an AP/P2P_GO link without disrupting other
links on the same interface.
Signed-off-by: Manish Dharanenthiran <manish.dharanenthiran@oss.qualcomm.com>
Link: https://patch.msgid.link/20251127-stop_link-v2-1-43745846c5fd@qti.qualcomm.com
[make cfg80211_stop_iface() inline]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The normal timer mechanism assume that timeout further in the future
need a lower accuracy. As an example, the granularity for a timer
scheduled 4096 ms in the future on a 1000 Hz system is already 512 ms.
This granularity is perfectly sufficient for e.g. timeouts, but there
are other types of events that will happen at a future point in time and
require a higher accuracy.
Add a new wiphy_hrtimer_work type that uses an hrtimer internally. The
API is almost identical to the existing wiphy_delayed_work and it can be
used as a drop-in replacement after minor adjustments. The work will be
scheduled relative to the current time with a slack of 1 millisecond.
CC: stable@vger.kernel.org # 6.4+
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20251028125710.7f13a2adc5eb.I01b5af0363869864b0580d9c2a1770bafab69566@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The drivers should notify upper layers and user space when a NAN device
joins a cluster. This is needed, for example, to set the correct addr3
in SDF frames. Add API to report cluster join event.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250908140015.ad27b7b6e4d9.I70b213a2a49f18d1ba2ad325e67e8eff51cc7a1f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This notification will be used by the device to inform user space
about upcoming DW. When received, user space will be able to prepare
multicast Service Discovery Frames (SDFs) to be transmitted during the
next DW using %NL80211_CMD_FRAME command on the NAN management interface.
The device/driver will take care to transmit the frames in the correct
timing. This allows to implement a synchronized Discovery Engine (DE)
in user space, if the device doesn't support DE offload.
Note that this notification can be sent before the actual DW starts as
long as the driver/device handles the actual timing of the SDF
transmission.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250908140015.0e1d15031bab.I5b1721e61b63910452b3c5cdcdc1e94cb094d4c9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tracepoints that are defined take up around 5K each, even if they are not
used. If they are defined and not used, then they waste memory for unused
code. Soon unused tracepoints will cause warnings.
Remove the unused tracepoints of the cfg80211 subsystem. They are:
cfg80211_chandef_dfs_required
cfg80211_return_u32
cfg80211_return_uint
cfg80211_send_rx_auth
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://patch.msgid.link/20250828221759.131160ee@batman.local.home
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The upper layer may require the link ID to properly handle
unexpected frames. For instance, if hostapd, operating as an
AP MLD, receives a data frame from a non-associated STA,
it must send deauthentication to the link on which the STA is
operating.
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Reviewed-by: Money Wang <money.wang@mediatek.com>
Link: https://patch.msgid.link/20250721065159.1740992-1-michael-cy.lee@mediatek.com
[edit commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Hide the internal scan fields from mac80211 and drivers, the
'notified' variable is for internal tracking, and the 'info'
is output that's passed to cfg80211_scan_done() and stored
only for delayed userspace notification.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250609213231.6a62e41858e2.I004f66e9c087cc6e6ae4a24951cf470961ee9466@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-2-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the case of SME-in-driver, the driver can internally choose to
update the links based on the AP MLD recommendation and do link
reconfiguration negotiation with AP MLD.
(e.g., After the driver processing the BSS Transition Management request
frame received from the AP MLD with Neighbor Report containing
Multi-Link element with recommended links information chooses to do link
reconfiguration negotiation with AP MLD).
To support this, extend cfg80211_mlo_reconf_add_done() and
NL80211_CMD_ASSOC_MLO_RECONF to indicate added links information for
driver-initiated link reconfiguration requests. For removed links,
the driver indicates links information using the
NL80211_CMD_LINKS_REMOVED event for driver-initiated cases, the same as
supplicant initiated cases.
For the driver-initiated case, cfg80211 will receive link
reconfiguration result asynchronously from driver so holding BSSes of
the accepted add links is needed in the event path. Also, no need of
unhold call for the rejected add link BSSes since there was no hold call
happened previously.
Once the supplicant receives the NL80211_CMD_ASSOC_MLO_RECONF event,
it needs to process the information about newly added links and install
per-link group keys (e.g., GTK/IGTK/BIGTK etc.).
In case of the SME-in-driver, using a vendor interface etc. to notify
the supplicant to initiate a link reconfiguration request and then
supplicant sending command to the cfg80211 can lead to race conditions.
The correct design to avoid this is that the driver indicates the
cfg80211 directly with the results of the link reconfiguration
negotiation.
Signed-off-by: Kavita Kavita <quic_kkavita@quicinc.com>
Link: https://patch.msgid.link/20250604105757.2542-3-quic_kkavita@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some extended MLD capabilities and operations bits (currently
the "BTM MLD Recommendataion For Multiple APs Support" bit)
may depend on userspace capabilities. Allow userspace to pass
the values for this field that it supports to the association
and link reconfiguration operations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Link: https://patch.msgid.link/20250308225541.bd52078b5f65.I4dd8f53b0030db7ea87a2e0920989e7e2c7b5345@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for configuring Emergency Preparedness Communication
Services (EPCS) for station mode.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250102161730.ea54ac94445c.I11d750188bc0871e13e86146a3b5cc048d853e69@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, TX power is reported on interface/wdev level as
part of NL80211_CMD_GET_INTERFACE. With MLO, Multiple links
can be part of an interface/wdev and hence its necessary to
report the TX power of each link.
Add support to send tx power for all valid links of an MLD as
part of NL80211_CMD_GET_INTERFACE request.
As far as userspace is concerned, there is no behavioral change
for Non-ML Interfaces. For ML interfaces, userspace should fetch
TX power that is nested inside NL80211_ATTR_MLO_LINKS, similar to
how channel info(NL80211_ATTR_WIPHY_FREQ) is fetched.
Co-developed-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://patch.msgid.link/20241125083217.216095-2-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, during starting a radar detection, no link id information is
parsed and passed down. In order to support starting radar detection
during Multi Link Operation, it is required to pass link id as well.
Add changes to first parse and then pass link id in the start radar
detection path.
Additionally, update notification APIs to allow drivers/mac80211 to
pass the link ID.
However, everything is handled at link 0 only until all API's are ready to
handle it per link.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20240906064426.2101315-6-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
rdev_end_cac trace event is linked with wiphy_netdev_evt event class.
There is no option to pass link ID currently to wiphy_netdev_evt class.
A subsequent change would pass link ID to rdev_end_cac event and hence
it can no longer derive the event class from wiphy_netdev_evt.
Therefore, unlink rdev_end_cac event from wiphy_netdev_evt and define it's
own independent trace event. Link ID would be passed in subsequent change.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20240906064426.2101315-4-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a regulatory flag to allow VLP AP operation even on
channels otherwise marked NO_IR, which may be possible
in some regulatory domains/countries.
Note that this requires checking also when the beacon is
changed, since that may change the regulatory power type.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240523120945.63792ce19790.Ie2a02750d283b78fbf3c686b10565fb0388889e2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The first "new features" pull request for v6.11 with changes both in
stack and in drivers. Nothing out of ordinary, except that we have two
conflicts this time:
CONFLICT (content): Merge conflict in net/mac80211/cfg.c
CONFLICT (content): Merge conflict in drivers/net/wireless/microchip/wilc1000/netdev.c
Here are Stephen's resolutions for them:
https://lore.kernel.org/all/20240531124415.05b25e7a@canb.auug.org.au/https://lore.kernel.org/all/20240603110023.23572803@canb.auug.org.au/
Major changes:
cfg80211/mac80211
* parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers
wilc1000
* read MAC address during probe to make it visible to user space
iwlwifi
* bump FW API to 91 for BZ/SC devices
* report 64-bit radiotap timestamp
* Enable P2P low latency by default
* handle Transmit Power Envelope (TPE) advertised by AP
* start using guard()
rtlwifi
* RTL8192DU support
ath12k
* remove unsupported tx monitor handling
* channel 2 in 6 GHz band support
* Spatial Multiplexing Power Save (SMPS) in 6 GHz band support
* multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA) support
* dynamic VLAN support
* add panic handler for resetting the firmware state
ath10k
* add qcom,no-msa-ready-indicator Device Tree property
* LED support for various chipsets
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmZi07URHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZu3/QgAo7jyKgvpwMaNIVRLyfYCo0r3Q9wb7QPd
QeRNsftYxlWpPTJ4+Y95aZupy91Ay+RaEQXbbtl7PMIiyQrs7wb4V4Iqzedkws3t
DZsR5BitH+1BIGY0Omo0fiSB5HlWEwZGUj6inqlgKHpBtdIVTANSMjuwkdoMAV5y
ZU57axIGToySvDbRlhJQW833Nnh4KnaseA+TtyfXSaBVerzbshkjBr0d9pMBMiH9
irMQW5CW+7fbxp3OCNsKxX4eG6MFGmm/uP1hFmeYQi2qzUE4SddHMeV4I6oNKOrH
vFB+ZVmYvOjJUYsNhlCUe6Vy+EKwvmfiDWwE1egelEkgozCixJXAAQ==
=QT4C
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.11
The first "new features" pull request for v6.11 with changes both in
stack and in drivers. Nothing out of ordinary, except that we have
two conflicts this time:
net/mac80211/cfg.c
https://lore.kernel.org/all/20240531124415.05b25e7a@canb.auug.org.au
drivers/net/wireless/microchip/wilc1000/netdev.c
https://lore.kernel.org/all/20240603110023.23572803@canb.auug.org.au
Major changes:
cfg80211/mac80211
* parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers
wilc1000
* read MAC address during probe to make it visible to user space
iwlwifi
* bump FW API to 91 for BZ/SC devices
* report 64-bit radiotap timestamp
* enable P2P low latency by default
* handle Transmit Power Envelope (TPE) advertised by AP
* start using guard()
rtlwifi
* RTL8192DU support
ath12k
* remove unsupported tx monitor handling
* channel 2 in 6 GHz band support
* Spatial Multiplexing Power Save (SMPS) in 6 GHz band support
* multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA)
support
* dynamic VLAN support
* add panic handler for resetting the firmware state
ath10k
* add qcom,no-msa-ready-indicator Device Tree property
* LED support for various chipsets
* tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (194 commits)
wifi: ath12k: add hw_link_id in ath12k_pdev
wifi: ath12k: add panic handler
wifi: rtw89: chan: Use swap() in rtw89_swap_sub_entity()
wifi: brcm80211: remove unused structs
wifi: brcm80211: use sizeof(*pointer) instead of sizeof(type)
wifi: ath12k: do not process consecutive RDDM event
dt-bindings: net: wireless: ath11k: Drop "qcom,ipq8074-wcss-pil" from example
wifi: ath12k: fix memory leak in ath12k_dp_rx_peer_frag_setup()
wifi: rtlwifi: handle return value of usb init TX/RX
wifi: rtlwifi: Enable the new rtl8192du driver
wifi: rtlwifi: Add rtl8192du/sw.c
wifi: rtlwifi: Constify rtl_hal_cfg.{ops,usb_interface_cfg} and rtl_priv.cfg
wifi: rtlwifi: Add rtl8192du/dm.{c,h}
wifi: rtlwifi: Add rtl8192du/fw.{c,h} and rtl8192du/led.{c,h}
wifi: rtlwifi: Add rtl8192du/rf.{c,h}
wifi: rtlwifi: Add rtl8192du/trx.{c,h}
wifi: rtlwifi: Add rtl8192du/phy.{c,h}
wifi: rtlwifi: Add rtl8192du/hw.{c,h}
wifi: rtlwifi: Add new members to struct rtl_priv for RTL8192DU
wifi: rtlwifi: Add rtl8192du/table.{c,h}
...
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
Link: https://lore.kernel.org/r/20240607093517.41394C2BBFC@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add trace events to trace when wiphy works are queued (or
delayed ones scheduled), and other APIs are called. Also
add an event when the worker starts, before acquiring the
mutex, to be able to see potential delays due to locking.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://msgid.link/20240506210002.bf1840a1d22d.I4abba048c1c4017345640219cf1384a0b2288dd3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
Currently, during color change, no link id information is passed down.
In order to support color change during Multi Link Operation, it is
required to pass link id as well.
Additionally, update notification APIs to allow drivers/mac80211 to
pass the link ID.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240422053412.2024075-2-quic_adisi@quicinc.com
Link: https://msgid.link/20240422053412.2024075-3-quic_adisi@quicinc.com
[squash, actually only pass 0 from mac80211]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The declarations of the tx_rx_evt class and the rdev_set_antenna event
use the wrong order of arguments in the TP_ARGS macro.
Fix the order of arguments in the TP_ARGS macro.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Igor Artemiev <Igor.A.Artemiev@mcst.ru>
Link: https://msgid.link/20240405152431.270267-1-Igor.A.Artemiev@mcst.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the order of arguments in the TP_ARGS macro
for the rdev_dump_mpp tracepoint event.
Found by Linux Verification Center (linuxtesting.org).
Signed-off-by: Igor Artemiev <Igor.A.Artemiev@mcst.ru>
Link: https://msgid.link/20240311164519.118398-1-Igor.A.Artemiev@mcst.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently whenever NL80211_CMD_DEL_STATION command is called without any
MAC address, all stations present on that interface are flushed.
However with MLO there is a need to flush such stations only which are
using at least a particular link from the AP MLD interface.
For example - 2 GHz and 5 GHz are part of an AP MLD.
To this interface, following stations are connected -
1. One non-EHT STA on 2 GHz link.
2. One non-EHT STA on 5 GHz link.
3. One Multi-Link STA having 2 GHz and 5 GHz as active links.
Now if currently, NL80211_CMD_DEL_STATION is issued by the 2 GHz link
without any MAC address, it would flush all station entries. However,
flushing of station entry #2 at least is not desireable since it
is connected to 5 GHz link alone.
Hence, add an option to pass link ID as well in the command so that if link
ID is passed, stations using that passed link ID alone would be flushed
and others will not.
So after this, station entries #1 and #3 alone would be flushed and #2 will
remain as it is.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240205162952.1697646-2-quic_adisi@quicinc.com
[clarify documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, during channel switch, no link id information is passed down.
In order to support channel switch during Multi Link Operation, it is
required to pass link id as well.
Add changes to pass link id in the channel_switch cfg80211_ops.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-2-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Aloka originally suggested that puncturing should be part of
the chandef, so that it's treated correctly. At the time, I
disagreed and it ended up not part of the chandef, but I've
now realized that this was wrong. Even for clients, the RX,
and perhaps more importantly, CCA configuration needs to take
puncturing into account.
Move puncturing into the chandef, and adjust all the code
accordingly. Also add a few tests for puncturing in chandef
compatibility checking.
Link: https://lore.kernel.org/linux-wireless/20220214223051.3610-1-quic_alokad@quicinc.com/
Suggested-by: Aloka Dixit <quic_alokad@quicinc.com>
Link: https://msgid.link/20240129194108.307183a5d2e5.I4d7fe2f126b2366c1312010e2900dfb2abffa0f6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for setting the TID to link mapping for a non-AP MLD
station.
This is useful in cases user space needs to restrict the possible
set of active links, e.g., since it got a BSS Transition Management
request forcing to use only a subset of the valid links etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231211085121.da4d56a5f3ff.Iacf88e943326bf9c169c49b728c4a3445fdedc97@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
make htmldocs warns:
Documentation/driver-api/80211/cfg80211:48: ./include/net/cfg80211.h:7290: WARNING: Duplicate C declaration, also defined at cfg80211:7251.
Declaration is '.. c:function:: void cfg80211_rx_assoc_resp (struct net_device *dev, struct cfg80211_rx_assoc_resp *data)'.
This is because there's a function named cfg80211_rx_assoc_resp() and a struct
named cfg80211_rx_assoc_resp, see previous patch for more info.
To workaround this rename the struct to cfg80211_rx_assoc_resp_data. The
parameter for the function is named 'data' anyway so the naming here is
consistent.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231012114229.2931808-3-kvalo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using the full struct cfg80211_ap_settings for an update is
misleading, since most settings cannot be updated. Split the
update case off into a new struct cfg80211_ap_update.
Change-Id: I3ba4dd9280938ab41252f145227a7005edf327e4
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Modify the prototype for change_beacon() in struct cfg80211_op to
accept cfg80211_ap_settings instead of cfg80211_beacon_data so that
it can process data in addition to beacons.
Modify the prototypes of ieee80211_change_beacon() and driver specific
functions accordingly.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20230727174100.11721-4-quic_alokad@quicinc.com
[while at it, remove pointless "if (info)" check in tracing that just
makes all the lines longer than they need be - it's never NULL]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There really isn't any support for scanning at different
channel widths than 20 MHz since there's no way to set it.
Remove this support for now, if somebody wants to maintain
this whole thing later we can revisit how it should work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
STA MLD setup links may get removed if AP MLD remove the corresponding
affiliated APs with Multi-Link reconfiguration as described in
P802.11be_D3.0, section 35.3.6.2.2 Removing affiliated APs. Currently,
there is no support to notify such operation to cfg80211 and userspace.
Add support for the drivers to indicate STA MLD setup links removal to
cfg80211 and notify the same to userspace. Upon receiving such
indication from the driver, clear the MLO links information of the
removed links in the WDEV.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20230317142153.237900-1-quic_vjakkam@quicinc.com
[rename function and attribute, fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This new function is called from within the inform_bss(_frame)_data
functions in order for the driver to update data that it is tracking.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230616094949.8d7781b0f965.I80041183072b75c081996a1a5a230b34aff5c668@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multi-link operation(MLO) TDLS management
frames need to be transmitted on a specific link.
The TDLS setup request will add BSSID along with
peer address and userspace will pass the link-id
based on BSSID value to the driver(or mac80211).
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230616094948.cb3d87c22812.Ia3d15ac4a9a182145bf2d418bcb3ddf4539cd0a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
strlcpy() reads the entire source buffer first.
This read may exceed the destination size limit.
This is both inefficient and can lead to linear read
overflows if a source string is not NUL-terminated [1].
In an effort to remove strlcpy() completely [2], replace
strlcpy() here with strscpy().
Direct replacement is safe here since WIPHY_ASSIGN is only used by
TRACE macros and the return values are ignored.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy
[2] https://github.com/KSPP/linux/issues/89
Signed-off-by: Azeem Shaikh <azeemshaikh38@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230612232301.2572316-1-azeemshaikh38@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a command to enable and disable HW timestamping of TM and FTM
frames. HW timestamping can be enabled for a specific mac address
or for all addresses.
The low level driver will indicate how many peers HW timestamping
can be enabled concurrently, and this information will be passed
to userspace.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230301115906.05678d7b1c17.Iccc08869ea8156f1c71a3111a47f86dd56234bd0@changeid
[switch to needing netdev UP, minor edits]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
