In client mode, the extended capabilities are handled by the kernel
looking at the association frame. When the supplicant installs the keys
it calls sta_apply_parameters and it doesn't include the extended
capabilities since those can't change after association.
As a result, we overrode the max_amsdu_subframes that we set after
association.
Check that the ext_capa coming from the user space is valid before
looking at it. If the ext_capa is NULL, it really means that the
extended capabilities are not changed (as opposed to cleared).
The default value for max_amsdu_subframes is 0, which means there is no
limit. This value is valid and in case the association response frame
does not have extended capabilities, this is the value we should use.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221079
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260513170623.828dbb58c782.Ifd2bfc190c26140e919127adb02ffddd7b551499@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current code does not support establishing MLO connections for
interfaces operating in 4-address AP_VLAN mode.
MLO bringup is blocked by sanity checks in cfg.c, iface.c, and mlme.c,
which prevent MLD initialization when use_4addr is enabled.
Remove these restrictions to allow 4-address AP_VLAN interfaces to
initialize as part of an MLD and successfully participate in MLO
connections. This patch series also adds the necessary changes to
support WDS operation in MLO, making these modifications valid.
Allow 4-address mode interfaces to:
- Proceed with MLD initialization during interface setup
- Add MLO links dynamically via ieee80211_add_intf_link()
- Establish associations with MLO-capable access points
- Support AP_VLAN interfaces with MLO parent APs
Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com>
Link: https://patch.msgid.link/20260326164723.553927-4-tamizh.raja@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current code does not provide any link-configuration support
for 4-address mode WDS AP_VLAN interfaces in MLO setups, preventing
MLD stations from being added correctly. Add the required handling
to enable proper integration of 4-address WDS stations into
an MLO environment.
When a 4-address station associates with an MLO AP, compute the
intersection of valid links between the master AP interface and
the station's advertised capabilities. Configure the AP_VLAN interface
with only these common links to ensure correct data-path operation.
This update ensures AP_VLAN interfaces correctly track link-state
transitions and maintain consistent addressing across all active MLO links.
Co-developed-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Signed-off-by: Tamizh Chelvam Raja <tamizh.raja@oss.qualcomm.com>
Link: https://patch.msgid.link/20260326164723.553927-2-tamizh.raja@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Keys may be added to the NAN interfaces to protect
NAN management frames and data, allow that.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260326121156.34961ba9a0c4.I5b7c646c456d4112e5ab8663026153ace9b6b7d6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A carrier of an NDI interface is turned on when there is at least one NDI
station that: (1) correlates to this interface (2) is authorized (3) the
NAN peer to which this station belongs has at least one common slot with
the local schedule. Otherwise, it is turned off.
(common slots are slots where both schedules are active on compatible
channels.)
Implement the calculation of the carrier state and trigger it when
needed.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260326121156.98ff4115406f.Ie796487ab9eb23cda819b0afac57e7267b134911@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Peer schedules specify which channels the peer is available on and when.
Add support for configuring peer NAN schedules:
- build and store the schedule and maps
- for each channel, make sure that it fits into the capabilities, and
take the minimum between it and the local compatible nan channel.
- configure the driver
Note that the removal of a peer schedule should be done by the driver
upon NMI station removal.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260326121156.185ff2283fa6.I0345eb665be8ccf4a77eb1aca9a421eb8d2432e2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for both NMI and NDI stations.
The NDI station will be linked to the NMI station of the NAN peer for
which the NDI station is added.
A peer can choose to reuse its NMI address as the NDI address.
Since different keys might be in use for NAN management and for data
frames, we will have 2 different stations, even if they'll have the same
address.
Even though there are no links in NAN, sta->deflink will still be used
to store the one set of capabilities and SMPS mode.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260326121156.9fdd37b8e755.I7a7bd6e8e751cab49c329419485839afd209cfc6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A NAN local schedule consist of a list of NAN channels, and an array
that maps time slots to the channel it is scheduled to (or NULL to indicate
unscheduled).
A NAN channel is the configuration of a channel which is used for NAN
operations. It is a new type of chanctx user (before, the only user is a
link). A NAN channel may not have a chanctx assigned if it is ULWed out.
A NAN channel may or may not be scheduled (for example, user space
may want to prepare the resources before the actual schedule is
configured).
Add management of the NAN local schedule.
Since we introduce a new chanctx user, also adjust the different
for_each_chanctx_user_* macros to visit also the NAN channels and take
those into account.
Co-developed-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260326121156.03350fd40630.Id158f815cfc9b5ab1ebdb8ee608bda426e4d7474@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NAN DE (Discovery Engine) may be handled in the device or in user space.
When handled in user space, all the NAN func management code should not
run. Moreover, devices with user space DE should not provide the
add/del_nan_func callbaks. For such devices, ieee80211_reconfig_nan will
always fail.
Make it clear what parts of ieee80211_if_nan are relevant to DE
management, and touch those only when DE is offloaded.
Add a check that makes sure that a driver doesn't register with
add_del/nan_func callbacks if DE is in user space.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260326121156.6665f64865cd.Iee24bef3bae2e1d502216192e760c1e699d271c9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- cfg80211: new APIs for NAN (Neighbor Aware Networking,
aka Wi-Fi Aware) so less work must be in firmware
- mt76:
- mt7996/mt7925 MLO fixes/improvements
- mt7996 NPU support (HW eth/wifi traffic offload)
- iwlwifi: UNII-9 and continuing UHR work
-----BEGIN PGP SIGNATURE-----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=zap4
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2026-03-26' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
A fairly big set of changes all over, notably with:
- cfg80211: new APIs for NAN (Neighbor Aware Networking,
aka Wi-Fi Aware) so less work must be in firmware
- mt76:
- mt7996/mt7925 MLO fixes/improvements
- mt7996 NPU support (HW eth/wifi traffic offload)
- iwlwifi: UNII-9 and continuing UHR work
* tag 'wireless-next-2026-03-26' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (230 commits)
wifi: mac80211: ignore reserved bits in reconfiguration status
wifi: cfg80211: allow protected action frame TX for NAN
wifi: ieee80211: Add some missing NAN definitions
wifi: nl80211: Add a notification to notify NAN channel evacuation
wifi: nl80211: add NL80211_CMD_NAN_ULW_UPDATE notification
wifi: nl80211: allow reporting spurious NAN Data frames
wifi: cfg80211: allow ToDS=0/FromDS=0 data frames on NAN data interfaces
wifi: nl80211: define an API for configuring the NAN peer's schedule
wifi: nl80211: add support for NAN stations
wifi: cfg80211: separately store HT, VHT and HE capabilities for NAN
wifi: cfg80211: add support for NAN data interface
wifi: cfg80211: make sure NAN chandefs are valid
wifi: cfg80211: Add an API to configure local NAN schedule
wifi: mac80211: cleanup error path of ieee80211_do_open
wifi: mac80211: extract channel logic from link logic
wifi: iwlwifi: mld: set RX_FLAG_RADIOTAP_TLV_AT_END generically
wifi: iwlwifi: reduce the number of prints upon firmware crash
wifi: iwlwifi: fix the description of SESSION_PROTECTION_CMD
wifi: iwlwifi: mld: introduce iwl_mld_vif_fw_id_valid
wifi: iwlwifi: mld: block EMLSR during TDLS connections
...
====================
Link: https://patch.msgid.link/20260326152021.305959-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This new interface type represents a NAN data interface (NDI).
It is used for data communication with NAN peers.
Note that the existing NL80211_IFTYPE_NAN interface, which is the NAN
Management Interface (NMI), is used for management communication.
An NDI interface is started when a new NAN data path is about to
be established, and is stopped after the NAN data path is terminated.
- An NDI interface can only be started if the NMI is running, and NAN is
started.
- Before the NMI is stopped, the NDI interfaces will be stopped.
Add the new interface type, handle add/remove operations for it,
and makes sure of the conditions above.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260219114327.0d681335c2e2.I92973483e927820ae2297853c141842fdb262747@changeid
Link: https://patch.msgid.link/20260318123926.206536-4-miriam.rachel.korenblit@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In NAN, we have one set of (HT, VHT, HE) capabilities for all bands,
which means that we will need to process those capabilities without a
given sband.
To prepare for that, remove the sband argument from
ieee80211_ht_cap_ie_to_sta_ht_cap and ieee80211_he_cap_ie_to_sta_he_cap
and pass our own capabilities instead.
For ieee80211_vht_cap_ie_to_sta_vht_cap, make the sband argument
optional, since it is also used to check if there is at least one channel
that supports 80 MHz.
(Note that this check doesn't make much sense, but this can be handled in
a different patch.)
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260320141504.e42ef1f0eabb.If994d6346f00219437e22043e7bf2395b827b34a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We shouldn't remove keys before disable beaconing, at least when
beacon protection is used, since that would remove keys that are
still used for beacon transmission at the same time. Stop before
removing keys so there's no race.
Fixes: af2d14b01c ("mac80211: Beacon protection using the new BIGTK (STA)")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260303150339.574e7887b3ab.I50d708f5aa22584506a91d0da7f8a73ba39fceac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently key installation is only supported for netdev. For NAN,
support most key operations (except setting default data key) on
wdevs instead of netdevs, and adjust all the APIs and tracing to
match.
Since nothing currently sets NL80211_EXT_FEATURE_SECURE_NAN, this
doesn't change anything (P2P Device already isn't allowed.)
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260107150057.69a0cfad95fa.I00efdf3b2c11efab82ef6ece9f393382bcf33ba8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_nan_conf::cluster_id is currently a pointer, but there is no real
reason to not have it an array. It makes things easier as there is no
need to check the pointer validity each time.
If a cluster ID wasn't provided by user space it will be randomized.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260302091108.2b12e4ccf5bb.Ib16bf5cca55463d4c89e18099cf1dfe4de95d405@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, a station can only be added to a netdev interface,
mainly because there was no need for a station of a non-netdev
interface.
But for NAN, we will have stations that belong to the NL80211_IFTYPE_NAN
interface.
Prepare for adding/changing/deleting a station that belongs to a non-netdev
interface. This doesn't actually allow such stations - this will be done
in a different patch.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260219114327.65c9cc96f814.Ic02066b88bb8ad6b21e15cbea8d720280008c83b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, for AP MLD, the link ID is not provided when a NULL
packet is triggered to probe a station. For non-MLO stations connected
to an AP MLD, use the station's default link to send the NULL packets
and set addr2 and addr3 to the link address. For MLO stations, set the
link ID to unspecified to let the driver select the appropriate link.
Co-developed-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Signed-off-by: Suraj P Kizhakkethil <suraj.kizhakkethil@oss.qualcomm.com>
Link: https://patch.msgid.link/20260213100126.1414398-3-suraj.kizhakkethil@oss.qualcomm.com
[init link_id in each branch instead of default to zero]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, when sending a NULL frame to probe a station, the band
information is derived from the chanctx_conf in the mac80211 vif's
bss_conf. However, for AP MLD, chanctx_conf is not assigned to the
vif's bss_conf; instead it is assigned on a per-link basis. As a result,
for AP MLD, sending a NULL packet to probe will trigger a warning.
WARNING: net/mac80211/cfg.c:4635 at ieee80211_probe_client+0x1a8/0x1d8 [mac80211], CPU#2: hostapd/244
Call trace:
ieee80211_probe_client+0x1a8/0x1d8 [mac80211] (P)
nl80211_probe_client+0xac/0x170 [cfg80211]
genl_family_rcv_msg_doit+0xc8/0x134
genl_rcv_msg+0x200/0x280
netlink_rcv_skb+0x38/0xf0
genl_rcv+0x34/0x48
netlink_unicast+0x314/0x3a0
netlink_sendmsg+0x150/0x390
____sys_sendmsg+0x1f4/0x21c
___sys_sendmsg+0x98/0xc0
__sys_sendmsg+0x74/0xcc
__arm64_sys_sendmsg+0x20/0x34
invoke_syscall.constprop.0+0x4c/0xd0
do_el0_svc+0x3c/0xd0
el0_svc+0x28/0xc0
el0t_64_sync_handler+0x98/0xdc
el0t_64_sync+0x154/0x158
---[ end trace 0000000000000000 ]---
For NULL packets sent to probe stations, set the band information only
for non-MLD, since MLD transmissions does not rely on band.
Signed-off-by: Suraj P Kizhakkethil <suraj.kizhakkethil@oss.qualcomm.com>
Link: https://patch.msgid.link/20260213100126.1414398-2-suraj.kizhakkethil@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
Prior initiating communication in a DFS channel, there should be a
monitoring of RADAR in that channel for a minimum of 600 seconds if it
is a Weather RADAR channel and 60 seconds for other DFS channels. This
Channel Availability Check(CAC) is currently implemented by scheduling
a work item for execution with a delay equal to an appropriate timeout.
But this work item is observed to take more delay than specified
(4-5 seconds in regular DFS channels and 25-30 seconds in Weather RADAR
channels). Even though this delay is expected in case of delayed work
queue as there is no guarantee that the work will be scheduled exactly
after the specified delay, a delay of more than 20 seconds is too much
for the AP to be in non-operational state.
Recently commit 7ceba45a66 ("wifi: cfg80211: add an hrtimer based
delayed work item") added an infrastructure to overcome this issue by
supporting high resolution timers for mac80211 delayed work, which do not
have this timeout latency. Switch the CAC timeout to use this
infrastructure, so the CAC completion handling is triggered with tighter
timing and reduced latency.
Signed-off-by: Amith A <amith.a@oss.qualcomm.com>
Link: https://patch.msgid.link/20260130035511.2328713-1-amith.a@oss.qualcomm.com
[fix delay handling]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, mac80211 allows key installation only after association
completes. However, Enhanced Privacy Protection Key Exchange (EPPKE)
requires key installation before association to enable encryption and
decryption of (Re)Association Request and Response frames.
Add support to install keys prior to association when the peer is an
Enhanced Privacy Protection (EPP) peer that requires encryption and
decryption of (Re)Association Request and Response frames.
Introduce a new boolean parameter "epp_peer" in the "ieee80211_sta"
profile to indicate that the peer supports the Enhanced Privacy
Protection Key Exchange (EPPKE) protocol. For non-AP STA mode, it
is set when the authentication algorithm is WLAN_AUTH_EPPKE during
station profile initialization. For AP mode, it is set during
NL80211_CMD_NEW_STA and NL80211_CMD_ADD_LINK_STA.
When "epp_peer" parameter is set, mac80211 now accepts keys before
association and enables encryption of the (Re)Association
Request/Response frames.
Co-developed-by: Sai Pratyusha Magam <sai.magam@oss.qualcomm.com>
Signed-off-by: Sai Pratyusha Magam <sai.magam@oss.qualcomm.com>
Signed-off-by: Kavita Kavita <kavita.kavita@oss.qualcomm.com>
Link: https://patch.msgid.link/20260114111900.2196941-6-kavita.kavita@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When ieee80211_check_combinations is called with NULL as the chandef,
the chanmode argument is not relevant. Send a don't care (0) instead.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260111192411.9aa743647b43.I407b3d878d94464ce01e25f16c6e2b687bcd8b5a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With cfg80211_stop_link() adding support to stop a link in AP/P2P_GO
mode, in failure cases only the corresponding link can be stopped,
instead of stopping the whole interface.
Hence, invoke cfg80211_stop_link() directly with the link_id set for
AP/P2P_GO mode when CSA finalization fails.
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Manish Dharanenthiran <manish.dharanenthiran@oss.qualcomm.com>
Link: https://patch.msgid.link/20251127-stop_link-v2-2-43745846c5fd@qti.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When userspace brings down and deletes a non-transmitted profile,
it is expected to send a new updated Beacon template for the
transmitted profile of that multiple BSSID (MBSSID) group which
does not include the removed profile in MBSSID element. This
update comes via NL80211_CMD_SET_BEACON.
Such updates work well as long as the group continues to have at
least one non-transmitted profile as NL80211_ATTR_MBSSID_ELEMS
is included in the new Beacon template.
But when the last non-trasmitted profile is removed, it still
gets included in Beacon templates sent to driver. This happens
because when no MBSSID elements are sent by the userspace,
ieee80211_assign_beacon() ends up using the element stored from
earlier Beacon template.
Do not copy old MBSSID elements, instead userspace should always
include these when applicable.
Fixes: 2b3171c6fe ("mac80211: MBSSID beacon handling in AP mode")
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Link: https://patch.msgid.link/20251215174656.2866319-2-aloka.dixit@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For monitoring, userspace will try to configure the VIF sdata, while the
driver may see the monitor_sdata that is created when only monitor
interfaces are up. This causes the odd situation that it may not be
possible to store the MU-MIMO configuration on monitor_sdata.
Fix this by storing that information on the VIF sdata and updating the
monitor_sdata when available and the interface is up. Also, adjust the
code that adds monitor_sdata so that it will configure MU-MIMO based on
the newly added interface or one of the existing ones.
This should give a mostly consistent behaviour when configuring MU-MIMO
on sniffer interfaces. Should the user configure MU-MIMO on multiple
sniffer interfaces, then mac80211 will simply select one of the
configurations. This behaviour should be good enough and avoids breaking
user expectations in the common scenarios.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20251110141514.677915f8f6bb.If4e04a57052f9ca763562a67248b06fd80d0c2c1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When ieee80211_stop_ap() deletes the FILS discovery and unsolicited
broadcast probe response templates, the associated interval values
are not reset. This can lead to drivers subsequently operating with
the non-zero values, leading to unexpected behavior.
Trigger repeated retrieval attempts of the FILS discovery template in
ath12k, resulting in excessive log messages such as:
mac vdev 0 failed to retrieve FILS discovery template
mac vdev 4 failed to retrieve FILS discovery template
Fix this by resetting the intervals in ieee80211_stop_ap() to ensure
proper cleanup of FILS discovery and unsolicited broadcast probe
response templates.
Fixes: 295b02c4be ("mac80211: Add FILS discovery support")
Fixes: 632189a018 ("mac80211: Unsolicited broadcast probe response support")
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Link: https://patch.msgid.link/20250924130014.2575533-1-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit a8bb74acd8 ("rcu: Consolidate RCU-sched update-side function definitions")
there is no difference between rcu_read_lock(), rcu_read_lock_bh() and
rcu_read_lock_sched() in terms of RCU read section and the relevant grace
period. That means that spin_lock(), which implies rcu_read_lock_sched(),
also implies rcu_read_lock().
There is no need no explicitly start a RCU read section if one has already
been started implicitly by spin_lock().
Simplify the code and remove the inner rcu_read_lock() invocation.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: pengdonglin <pengdonglin@xiaomi.com>
Signed-off-by: pengdonglin <dolinux.peng@gmail.com>
Link: https://patch.msgid.link/20250916044735.2316171-11-dolinux.peng@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case that NAN is started, mark the device as non idle,
and set LED triggering similar to scan and ROC. Set the
device to idle once NAN is stopped.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250908140015.2711d62fce22.I9b9f826490e50967a66788d713b0eba985879873@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 78a7a126dc ("wifi: mac80211: validate SCAN_FLAG_AP in scan request
during MLO") introduced a check that rejects scan requests if any link is
already beaconing. This works fine when all links share the same radio, but
breaks down in multi-radio setups.
Consider a scenario where a 2.4 GHz link is beaconing and a scan is
requested on a 5 GHz link, each backed by a different physical radio. The
current logic still blocks the scan, even though it should be allowed. As a
result, interface bring-up fails unnecessarily in valid configurations.
Fix this by checking whether the scan is being requested on the same
underlying radio as the beaconing link. Only reject the scan if it targets
a link that is already beaconing and the NL80211_FEATURE_AP_SCAN is not
set. This ensures correct behavior in multi-radio environments and avoids
false rejections.
Fixes: 78a7a126dc ("wifi: mac80211: validate SCAN_FLAG_AP in scan request during MLO")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250812-fix_scan_ap_flag_requirement_during_mlo-v4-3-383ffb6da213@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In several instances where cfg80211_get_radio_idx_by_chan() is called,
redundant checks are performed across function — such as verifying if
wiphy->n_radio < 2 or if the returned index is negative. These checks are
unnecessary, as the return value can be directly compared. Moreover, the
function can be safely called even when radio-level properties are not
explicitly advertised since in such case in each call it is going to get
same error value.
Therefore, simplify the usage of this function across all such cases by
removing redundant conditions and relying on the return value directly.
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250812-fix_scan_ap_flag_requirement_during_mlo-v4-2-383ffb6da213@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An S1G TIM PVB is encoded differently compared to a non-s1g TIM PVB.
As the AP dictates which encoding mode it uses, here we only implement
block bitmap encoding. This is the default encoding mode used by
all current vendor implementations.
Additionally, S1G has a maximum AID count of 8192, however we are
limiting the current implementation to 1600. This has no resemblence
to the standard and is purely an implementation detail. The reason for
this is due to the TIM elements maximum length of 255. This allows for,
at most, 25 encoded blocks for a PVB encoded with block bitmap. Support
for the maximum of 8192 AIDs will require an implementation of page slicing
to be added to mac80211.
As a result, we perform extra validation on both the STA and AP side
when receiving an AID as an S1G interface.
Add support for block bitmap encoding for an S1G AP and limit the
maximum AID count to 1600 for the current mac80211 implementations.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250725132221.258217-2-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While I caught the need for setting cnt early in nl80211_parse_rnr_elems()
in the original annotation of struct cfg80211_rnr_elems with __counted_by,
I missed a similar pattern in ieee80211_copy_rnr_beacon(). Fix this by
moving the cnt assignment to before the loop.
Fixes: 7b6d708703 ("wifi: cfg80211: Annotate struct cfg80211_rnr_elems with __counted_by")
Signed-off-by: Kees Cook <kees@kernel.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/20250721182521.work.540-kees@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce the sb_count variable which tracks the number of
beacon intervals until the next long beacon. To initialise this
value, we find the current short beacon index into this period
which represents the number of short beacons left to send before
the next long beacon. We use the same TSF value used to initialise
the DTIM count to ensure the short beacon count and DTIM count
are in sync as its common for the long beacon period and DTIM period
to be equivalent.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250717074205.312577-4-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce the ability to parse the short beacon data and long
beacon period. The long beacon period represents the number of beacon
intervals between each long beacon transmission. Additionally,
as a BSS cannot change its configuration such that short beaconing
is dynamically disabled/enabled without tearing down the interface
- we ensure we have an existing short beacon before performing
the update.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250717074205.312577-3-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ieee80211_csa_finish() function currently uses for_each_sdata_link()
to iterate over links of sdata. However, this macro internally uses
wiphy_dereference(), which expects the wiphy->mtx lock to be held.
When ieee80211_csa_finish() is invoked under an RCU read-side critical
section (e.g., under rcu_read_lock()), this leads to a warning from the
RCU debugging framework.
WARNING: suspicious RCU usage
net/mac80211/cfg.c:3830 suspicious rcu_dereference_protected() usage!
This warning is triggered because wiphy_dereference() is not safe to use
without holding the wiphy mutex, and it is being used in an RCU context
without the required locking.
Fix this by introducing and using a new macro, for_each_sdata_link_rcu(),
which performs RCU-safe iteration over sdata links using
list_for_each_entry_rcu() and rcu_dereference(). This ensures that the
link pointers are accessed safely under RCU and eliminates the warning.
Fixes: f600832794 ("wifi: mac80211: restructure tx profile retrieval for MLO MBSSID")
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250711033846.40455-1-maharaja.kennadyrajan@oss.qualcomm.com
[unindent like the non-RCU macro]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During commands like channel switch and color change, the updated
unsolicited broadcast probe response template may be provided. However,
this data is not parsed or acted upon in mac80211.
Add support to parse it and set the BSS changed flag
BSS_CHANGED_UNSOL_BCAST_PROBE_RESP so that drivers could take further
action.
Signed-off-by: Yuvarani V <quic_yuvarani@quicinc.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250710-update_unsol_bcast_probe_resp-v2-2-31aca39d3b30@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cross-merge networking fixes after downstream PR (net-6.16-rc6-2).
No conflicts.
Adjacent changes:
drivers/net/wireless/mediatek/mt76/mt7925/mcu.c
c701574c54 ("wifi: mt76: mt7925: fix invalid array index in ssid assignment during hw scan")
b3a431fe2e ("wifi: mt76: mt7925: fix off by one in mt7925_mcu_hw_scan()")
drivers/net/wireless/mediatek/mt76/mt7996/mac.c
62da647a2b ("wifi: mt76: mt7996: Add MLO support to mt7996_tx_check_aggr()")
dc66a129ad ("wifi: mt76: add a wrapper for wcid access with validation")
drivers/net/wireless/mediatek/mt76/mt7996/main.c
3dd6f67c66 ("wifi: mt76: Move RCU section in mt7996_mcu_add_rate_ctrl()")
8989d8e90f ("wifi: mt76: mt7996: Do not set wcid.sta to 1 in mt7996_mac_sta_event()")
net/mac80211/cfg.c
58fcb1b428 ("wifi: mac80211: reject VHT opmode for unsupported channel widths")
037dc18ac3 ("wifi: mac80211: add support for storing station S1G capabilities")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VHT operating mode notifications are not defined for channel widths
below 20 MHz. In particular, 5 MHz and 10 MHz are not valid under the
VHT specification and must be rejected.
Without this check, malformed notifications using these widths may
reach ieee80211_chan_width_to_rx_bw(), leading to a WARN_ON due to
invalid input. This issue was reported by syzbot.
Reject these unsupported widths early in sta_link_apply_parameters()
when opmode_notif is used. The accepted set includes 20, 40, 80, 160,
and 80+80 MHz, which are valid for VHT. While 320 MHz is not defined
for VHT, it is allowed to avoid rejecting HE or EHT clients that may
still send a VHT opmode notification.
Reported-by: syzbot+ededba317ddeca8b3f08@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=ededba317ddeca8b3f08
Fixes: 751e7489c1 ("wifi: mac80211: expose ieee80211_chan_width_to_rx_bw() to drivers")
Tested-by: syzbot+ededba317ddeca8b3f08@syzkaller.appspotmail.com
Signed-off-by: Moon Hee Lee <moonhee.lee.ca@gmail.com>
Link: https://patch.msgid.link/20250703193756.46622-2-moonhee.lee.ca@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to get the radio for which RTS threshold needs to be changed
from userspace. Pass on this radio index to underlying drivers as an
additional argument.
A value of -1 indicates radio index is not mentioned and that the
configuration applies to all radio(s) of the wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-5-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-2-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, if a link gets removed in between for a station then
directly accumulated data will fall down to sum of other active links.
This will bring inconsistency in station dump statistics.
For instance, let's take Tx packets
- at t=0-> link-0:2 link-1:3 Tx packets => accumulated = 5
- at t=1-> link-0:4 link-1:6 Tx packets => accumulated = 10
let say at t=2, link-0 went down => link-0:0 link-1:7 => accumulated = 7
Here, suddenly accumulated Tx packets will come down to 7 from 10.
This is showing inconsistency.
Therefore, store link-0 data when it went down and add to accumulated
Tx packet = 11.
Hence, store the removed link statistics data in sta structure and
add it in accumulated statistics for consistency.
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Link: https://patch.msgid.link/20250528054420.3050133-7-quic_sarishar@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, in ieee80211_assign_beacon() mbssid count is updated as link's
bssid_indicator. mbssid count is the total number of MBSSID elements in
the beacon instead of Max BSSID indicator of the Multiple BSS set.
This will result in drivers obtaining an invalid bssid_indicator for BSSes
in a Multiple BSS set.
Fix this by updating link's bssid_indicator from MBSSID element for
Transmitting BSS and update the same for all of its Non-Transmitting BSSes.
Fixes: dde78aa520 ("mac80211: update bssid_indicator in ieee80211_assign_beacon")
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20250530040940.3188537-1-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, in multi-radio wiphy cases, if a scan is ongoing on one radio,
-EBUSY is returned when DFS or a channel switch is initiated on another
radio. Because of this, an MLD AP with one radio (link) in an ongoing scan
cannot initiate DFS or a channel switch on another radio (link).
In multi-radio wiphy cases, multiple radios are grouped under a single
wiphy. Hence, if a scan is ongoing on one underlying radio and DFS or a
channel switch is requested on a different underlying radio of the same
wiphy, these operations can be allowed simultaneously.
Add logic to check the underlying radio used for the ongoing scan. If the
radio on which DFS or a channel switch is requested is not being used for
the scan, allow the operation; otherwise, return -EBUSY.
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Link: https://patch.msgid.link/20250527-mlo-dfs-acs-v2-2-92c2f37c81d9@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
