vringh_iov_pull_iotlb() returns a signed byte count. A failed TX pull is
currently added to the unsigned byte counter and then passed as a size_t
length to receive_filter() and vringh_iov_push_iotlb(). A negative error
can therefore become a large length in the RX path.
Handle non-positive pull results before every length use. Count the TX
error and complete the consumed TX descriptor with zero bytes.
I found this bug myself, though the patch was written with AI assistance.
Fixes: cfe2268929 ("vdpa_sim: filter destination mac address")
Assisted-by: OpenAI-Codex:GPT-5
Signed-off-by: Linfeng Sun <linfeng.sun.dev@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260901094842.25875-1-linfeng.sun.dev@gmail.com>
vdpasim_blk_check_range() logs an invalid start sector but continues
validating the request. The subsequent unsigned capacity subtraction can
underflow and let an out-of-range buffer offset reach the data path.
The invalid offset is used by three request paths. VIRTIO_BLK_T_OUT
copies guest data to blk->buffer + offset through
vringh_iov_pull_iotlb(), causing an out-of-bounds write in
_copy_from_iter() or memcpy(). VIRTIO_BLK_T_IN copies from
blk->buffer + offset to the guest through vringh_iov_push_iotlb(),
causing an out-of-bounds read in _copy_to_iter().
VIRTIO_BLK_T_WRITE_ZEROES passes blk->buffer + offset to memset(),
causing an out-of-bounds write.
Reject starts at or beyond the capacity before the subtraction. Treat the
capacity boundary as invalid because the IN and OUT paths round byte counts
down to sectors for validation but later copy the original byte counts. A
sub-sector request at the capacity boundary would otherwise still access
past the end of the buffer.
I found this bug myself, though the patch was written with AI assistance.
Fixes: 7d189f617f ("vdpa_sim_blk: implement ramdisk behaviour")
Assisted-by: OpenAI-Codex:GPT-5
Signed-off-by: Linfeng Sun <linfeng.sun.dev@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260901094800.25475-1-linfeng.sun.dev@gmail.com>
vdpasim_dma_map() updates the IOTLB and the passthrough (iommu_pt)
state under iommu_lock. vdpasim_dma_unmap() clears iommu_pt and
resets the IOTLB before taking iommu_lock, then deletes the mapping
while holding the lock.
A concurrent dma_map(), dma_unmap(), or reset path that also touches
the same address space can therefore observe or modify the IOTLB and
iommu_pt state without consistent locking.
Perform the passthrough transition and range deletion under the same
iommu_lock scope, matching dma_map().
Tested-on: openEuler VM (6.16.8, /usr/src/linux-6.16.8)
Tested-by: Xiong Weimin <xiongweimin@kylinos.cn>
Signed-off-by: Xiong Weimin <xiongweimin@kylinos.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260626020545.607600-3-15927021679@163.com>
vdpasim_kick_vq() sets pending_kick when a virtqueue is kicked while
the device is suspended (!running but DRIVER_OK). vdpasim_resume()
later replays kicks for all virtqueues when pending_kick is set.
vdpasim_do_reset() clears running and status but leaves pending_kick
unchanged. If a kick is deferred during suspend and the device is
reset before resume, a later resume can spuriously kick every
virtqueue even though no new work was queued after reset.
Clear pending_kick in vdpasim_do_reset() together with the other
device state that must not survive a reset.
Tested-on: openEuler VM (6.16.8, /usr/src/linux-6.16.8)
Tested-by: Xiong Weimin <xiongweimin@kylinos.cn>
Signed-off-by: Xiong Weimin <xiongweimin@kylinos.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260626020545.607600-2-15927021679@163.com>
vdpasim_create() leaves vdpasim->worker as an ERR_PTR when
kthread_run_worker() fails. The error path then drops the device
reference, which releases the partially initialized simulator.
vdpasim_free() unconditionally passes the worker pointer to
kthread_destroy_worker(), so the ERR_PTR is dereferenced and can trigger
a general protection fault.
Store the worker error, clear the pointer, and only clean up the worker
when it was successfully initialized. Also make the release path tolerate
partially initialized objects by guarding virtqueue and IOTLB cleanup,
since the same release path can be reached from other initialization
failures.
I found this bug myself, though the patch was written with AI assistance.
Fixes: 76acfa7bc5 ("vdpa_sim: use kthread worker")
Assisted-by: OpenAI-Codex:GPT-5
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Linfeng Sun <linfeng.sun.dev@gamil.com>
Message-ID: <20260620100959.2070316-1-slf@hdu.edu.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost_iotlb_add_range_ctx() only retires an old entry when the table
has a non-zero limit, has exactly reached that limit and has
VHOST_IOTLB_FLAG_RETIRE set. Non-retiring tables can keep allocating
entries after reaching their configured limit.
Existing vhost devices allocate their IOTLB with max_iotlb_entries from
vhost.c, which defaults to 2048 and is tunable by module parameter. Use
the caller-provided limit at the allocation point instead of adding a
separate default in the common IOTLB helper, and reject non-positive
values in vhost paths that can report an error.
Other vhost IOTLB users should not create zero-limit tables when entries
can be populated from userspace or guest-controlled requests. Add
caller-side max_iotlb_entries parameters for mlx5 vDPA, VDUSE and
vhost-vDPA. Reject non-positive VDUSE and vhost-vDPA values, and require
at least two entries for vdpa_sim and mlx5 vDPA paths that install
full-range mappings, since those mappings are split into two IOTLB
entries.
Handle full-range mappings in the common helper by checking that the
IOTLB can hold both split entries before inserting the first half. This
avoids returning an error after leaving a half mapping behind.
When the table is full, keep the existing retire behavior for retiring
tables and return -ENOSPC for non-retiring tables. Reuse the retired map
node instead of freeing it and allocating a replacement, so a stream of
IOTLB updates cannot keep forcing GFP_ATOMIC allocations after the table
has reached its limit. If a zero-limit IOTLB still reaches the common
helper, treat it as a configuration error and return -EINVAL.
I found this bug myself, though the patch was written with AI assistance.
Fixes: 0bbe30668d ("vhost: factor out IOTLB")
Assisted-by: OpenAI-Codex:GPT-5
Signed-off-by: Linfeng Sun <linfeng.sun.dev@gamil.com>
Message-ID: <AMYAtgAiKmgYcSQT5ukl-4qq.3.1781960405943.Hmail.241270009@hdu.edu.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Driver core expects devices to be dynamically allocated and will, for
example, complain loudly when no release function has been provided.
Use root_device_register() to allocate and register the root device
instead of open coding using a static device.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260424104703.2619093-3-johan@kernel.org>
Driver core expects devices to be dynamically allocated and will, for
example, complain loudly when no release function has been provided.
Use root_device_register() to allocate and register the root device
instead of open coding using a static device.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20260424104703.2619093-2-johan@kernel.org>
This converts some of the visually simpler cases that have been split
over multiple lines. I only did the ones that are easy to verify the
resulting diff by having just that final GFP_KERNEL argument on the next
line.
Somebody should probably do a proper coccinelle script for this, but for
me the trivial script actually resulted in an assertion failure in the
middle of the script. I probably had made it a bit _too_ trivial.
So after fighting that far a while I decided to just do some of the
syntactically simpler cases with variations of the previous 'sed'
scripts.
The more syntactically complex multi-line cases would mostly really want
whitespace cleanup anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
Remove duplication by consolidating these here. This reduces the
posibility of a parent driver missing them.
While we're at it, fix a bug in vdpa_sim where a valid ASID can be
assigned to a group equal to ngroups, causing an out of bound write.
Cc: stable@vger.kernel.org
Fixes: bda324fd03 ("vdpasim: control virtqueue support")
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20260119143306.1818855-2-eperezma@redhat.com>
Virtio core allows the transport to provide device or transport
specific mapping functions. This patch adds this support to vDPA. We
can simply do this by allowing the vDPA parent to register a
virtio_map_ops.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20250924070045.10361-2-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Virtio core switches from DMA device to virtio_map, let's do that
as well for vDPA.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20250821064641.5025-8-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
kthread_create() creates a kthread without running it yet. kthread_run()
creates a kthread and runs it.
On the other hand, kthread_create_worker() creates a kthread worker and
runs it.
This difference in behaviours is confusing. Also there is no way to
create a kthread worker and affine it using kthread_bind_mask() or
kthread_affine_preferred() before starting it.
Consolidate the behaviours and introduce kthread_run_worker[_on_cpu]()
that behaves just like kthread_run(). kthread_create_worker[_on_cpu]()
will now only create a kthread worker without starting it.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Add the function to support setting the MAC address.
For vdpa_sim_net, the driver will write the MAC address
to the config space, and other devices can implement
their own functions to support this.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20240731031653.1047692-3-lulu@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
This commit implements vdpa_config_ops.get_vq_size for vDPA
simulator, this new interface can help report per vq size.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240202163905.8834-7-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vdpasim_do_reset sets running to true, which is wrong, as it allows
vdpasim_kick_vq to post work requests before the device has been
configured. To fix, do not set running until VIRTIO_CONFIG_S_DRIVER_OK
is set.
Fixes: 0c89e2a3a9 ("vdpa_sim: Implement suspend vdpa op")
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <1707517807-137331-1-git-send-email-steven.sistare@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Deleting and recreating a device can lead to having the same
content as the old device, so let's always allocate buffers
completely zeroed out.
Fixes: abebb16254 ("vdpa_sim_blk: support shared backend")
Suggested-by: Qing Wang <qinwang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20231031144339.121453-1-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
In order to reduce excessive memory mapping cost in live migration and
VM reboot, it is desirable to decouple the vhost-vdpa IOTLB abstraction
from the virtio device life cycle, i.e. mappings can be kept intact
across virtio device reset. Leverage the .reset_map callback, which is
meant to destroy the iotlb on the given ASID and recreate the 1:1
passthrough/identity mapping. To be consistent, the mapping on device
creation is initiailized to passthrough/identity with PA 1:1 mapped as
IOVA. With this the device .reset op doesn't have to maintain and clean
up memory mappings by itself.
Additionally, implement .compat_reset to cater for older userspace,
which may wish to see mapping to be cleared during reset.
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Tested-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <1697880319-4937-8-git-send-email-si-wei.liu@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
If the shared_buffer allocation fails, need to unregister mgmt_dev first.
Cc: stable@vger.kernel.org
Fixes: abebb16254 ("vdpa_sim_blk: support shared backend")
Signed-off-by: Shawn.Shao <shawn.shao@jaguarmicro.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230821060333.1155-1-shawn.shao@jaguarmicro.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Start offering the feature in the simulator. Other parent drivers can
follow this code to offer it too.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Message-Id: <20230609092127.170673-5-eperezma@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The vdpa_sim_blk simulator uses a ramdisk as the backend. To test live
migration, we need two devices that share the backend to have the data
synchronized with each other.
Add a new module parameter to make the buffer shared between all devices.
The shared_buffer_mutex is used just to ensure that each operation is
atomic, but it is up to the user to use the devices knowing that the
underlying ramdisk is shared.
For example, when we do a migration, the VMM (e.g., QEMU) will guarantee
to write to the destination device, only after completing operations with
the source device.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20230407133658.66339-3-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, the vdpa_sim core does not use the buffer, but only
allocates it.
The buffer is used by devices differently, and some future devices
may not use it. So let's move all its management inside the devices.
Add a new `free` device callback called to clean up the resources
allocated by the device.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20230407133658.66339-2-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The new "use_va" module parameter (default: true) is used in
vdpa_alloc_device() to inform the vDPA framework that the device
supports VA.
vringh is initialized to use VA only when "use_va" is true and the
user's mm has been bound. So, only when the bus supports user VA
(e.g. vhost-vdpa).
vdpasim_mm_work_fn work is used to serialize the binding to a new
address space when the .bind_mm callback is invoked, and unbinding
when the .unbind_mm callback is invoked.
Call mmget_not_zero()/kthread_use_mm() inside the worker function
to pin the address space only as long as needed, following the
documentation of mmget() in include/linux/sched/mm.h:
* Never use this function to pin this address space for an
* unbounded/indefinite amount of time.
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20230404131734.45943-1-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The spinlock we use to protect the state of the simulator is sometimes
held for a long time (for example, when devices handle requests).
This also prevents us from calling functions that might sleep (such as
kthread_flush_work() in the next patch), and thus having to release
and retake the lock.
For these reasons, let's replace the spinlock with a mutex that gives
us more flexibility.
Suggested-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20230404131730.45920-1-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's use our own kthread to run device jobs.
This allows us more flexibility, especially we can attach the kthread
to the user address space when vDPA uses user's VA.
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20230404131725.45908-1-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let's move work management inside the vdpa_sim core.
This way we can easily change how we manage the works, without
having to change the devices each time.
Acked-by: Eugenio Pérez Martin <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20230404131721.45886-1-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Initialization must be completed before calling _vdpa_register_device()
since it can connect the device to the vDPA bus, so requests can arrive
after that call.
So for example vdpasim_net_work(), which uses the net->*_stats variables,
can be scheduled before they are initialized.
Let's move _vdpa_register_device() to the end of vdpasim_net_dev_add()
and add a comment to avoid future issues.
Fixes: 0899774cb3 ("vdpa_sim_net: vendor satistics")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20230329160321.187176-1-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Starting from an used_idx different than 0 is needed in use cases like
virtual machine migration. Not doing so and letting the caller set an
avail idx different than 0 causes destination device to try to use old
buffers that source driver already recover and are not available
anymore.
Since vdpa_sim does not support receive inflight descriptors as a
destination of a migration, let's set both avail_idx and used_idx the
same at vq start. This is how vhost-user works in a
VHOST_SET_VRING_BASE call.
Although the simple fix is to set last_used_idx at vdpasim_set_vq_state,
it would be reset at vdpasim_queue_ready. The last_avail_idx case is
fixed with commit 0e84f918fa ("vdpa_sim: not reset state in
vdpasim_queue_ready"). Since the only option is to make it equal to
last_avail_idx, adding the only change needed here.
This was discovered and tested live migrating the vdpa_sim_net device.
Fixes: 2c53d0f64c ("vdpasim: vDPA device simulator")
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230302181857.925374-1-eperezma@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are two spelling mistakes in some literal strings. Fix them.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Message-Id: <20230130092644.37002-1-colin.i.king@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
We used to (ab)use the DMA ops for setting up identical mappings in
the IOTLB. This patch tries to get rid of the those unnecessary DMA
ops by maintaining a simple identical/passthrough mappings by
default. When bound to virtio_vdpa driver, DMA API will simply use PA
as the IOVA and we will be all fine. When the vDPA bus tries to setup
customized mapping (e.g when bound to vhost-vDPA), the
identical/passthrough mapping will be removed.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221223060021.28011-1-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
This patch adds support for basic vendor stats that include counters
for tx, rx and cvq.
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221223055548.27810-5-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
This patch adds a new config ops callback to allow individual
simulator to implement the vendor stats callback.
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221223055548.27810-4-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Allow individual simulator to customize the allocation size.
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221223055548.27810-3-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows us to control the allocation size of the structure.
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221223055548.27810-2-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vDPA simulators are software emulated device, so let's switch to use
weak barriers to avoid extra overhead in the driver.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221221062146.15356-1-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Implement resume operation for vdpa_sim devices, so vhost-vdpa will
offer that backend feature and userspace can effectively resume the
device.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Message-Id: <15a4566826033c5dd9a2167e5cfb0ef4d90cea49.1672742878.git.sebastien.boeuf@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
VIRTIO_NET_S_LINK_UP is already returned in config reads since vdpasim
creation, but the feature bit was not offered to the driver.
Tested modifying VIRTIO_NET_S_LINK_UP and different values of "status"
in qemu virtio-net options, using vhost_vdpa.
Not considering as a fix, because there should be no driver trusting in
this config read before the feature flag.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20221117155502.1394700-1-eperezma@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
vdpasim_queue_ready calls vringh_init_iotlb, which resets split indexes.
But it can be called after setting a ring base with
vdpasim_set_vq_state.
Fix it by stashing them. They're still resetted in vdpasim_vq_reset.
This was discovered and tested live migrating the vdpa_sim_net device.
Fixes: 2c53d0f64c ("vdpasim: vDPA device simulator")
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20230118164359.1523760-2-eperezma@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
In the receive_filter(), should not drop the packet with the
broadcast/multicast address. Add the check for this
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20221214054306.24145-1-lulu@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
After commit bda324fd03 ("vdpasim: control virtqueue support"),
vdpasim->iommu became an array of IOTLB, so we should clean the
mappings of each free one by one instead of just deleting the ranges
in the first IOTLB which may leak maps.
Fixes: bda324fd03 ("vdpasim: control virtqueue support")
Cc: Gautam Dawar <gautam.dawar@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20221213090717.61529-1-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gautam Dawar <gautam.dawar@amd.com>
When we initialize vringh, we should pass the features and the
number of elements in the virtqueue negotiated with the driver,
otherwise operations with vringh may fail.
This was discovered in a case where the driver sets a number of
elements in the virtqueue different from the value returned by
.get_vq_num_max().
In vdpasim_vq_reset() is safe to initialize the vringh with
default values, since the virtqueue will not be used until
vdpasim_queue_ready() is called again.
Fixes: 2c53d0f64c ("vdpasim: vDPA device simulator")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20221110141335.62171-1-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
This patch implements features provisioning for vdpa_sim_net.
1) validating the provisioned features to be a subset of the parent
features.
2) clearing the features that is not wanted by the userspace
For example:
vdpasim_net:
supported_classes net
max_supported_vqs 3
dev_features MTU MAC CTRL_VQ CTRL_MAC_ADDR ANY_LAYOUT VERSION_1 ACCESS_PLATFORM
1) provision vDPA device with all features that are supported by the
net simulator
dev1: mac 00:00:00:00:00:00 link up link_announce false mtu 1500
negotiated_features MTU MAC CTRL_VQ CTRL_MAC_ADDR VERSION_1 ACCESS_PLATFORM
2) provision vDPA device with a subset of the features
dev1: mac 00:00:00:00:00:00 link up link_announce false mtu 1500
negotiated_features CTRL_VQ VERSION_1 ACCESS_PLATFORM
Reviewed-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20220927074810.28627-3-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Expose VIRTIO_BLK_F_DISCARD and VIRTIO_BLK_F_WRITE_ZEROES features
to the drivers and handle VIRTIO_BLK_T_DISCARD and
VIRTIO_BLK_T_WRITE_ZEROES requests checking ranges and flags.
The simulator behaves like a ramdisk, so for VIRTIO_BLK_F_DISCARD
does nothing, while for VIRTIO_BLK_T_WRITE_ZEROES sets to 0 the
specified region.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20220811083632.77525-5-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The simulator behaves like a ramdisk, so we don't have to do
anything when a VIRTIO_BLK_T_FLUSH request is received, but it
could be useful to test driver behavior.
Let's expose the VIRTIO_BLK_F_FLUSH feature to inform the driver
that we support the flush command.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20220811083632.77525-4-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Next patches will add handling of other requests, where will be
useful to reuse vdpasim_blk_check_range().
So let's make it more generic by adding the `max_sectors` parameter,
since different requests allow different numbers of maximum sectors.
Let's also print the messages directly in vdpasim_blk_check_range()
to avoid duplicate prints.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20220811083632.77525-3-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
VIRTIO spec states: "The sector number indicates the offset
(multiplied by 512) where the read or write is to occur. This field is
unused and set to 0 for commands other than read or write."
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20220811083632.77525-2-sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implement suspend operation for vdpa_sim devices, so vhost-vdpa will
offer that backend feature and userspace can effectively suspend the
device.
This is a must before get virtqueue indexes (base) for live migration,
since the device could modify them after userland gets them. There are
individual ways to perform that action for some devices
(VHOST_NET_SET_BACKEND, VHOST_VSOCK_SET_RUNNING, ...) but there was no
way to perform it for any vhost device (and, in particular, vhost-vdpa).
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20220810171512.2343333-5-eperezma@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
