The PORTSC1 register has a different offset in Tegra20 compared to
Tegra30+, yet they share a crucial set of registers required for HSIC
functionality. Reflect this register offset change in the SoC config.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Link: https://patch.msgid.link/20260202080526.23487-5-clamor95@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The parallel transceiver select used in HSIC mode differs on Tegra20,
where it uses the UTMI value (0), whereas Tegra30+ uses a dedicated HSIC
value. Reflect this in the SoC config.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Link: https://patch.msgid.link/20260202080526.23487-4-clamor95@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return exact error value from utmi_wait_register during HSIC power on.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Link: https://patch.msgid.link/20260202080526.23487-3-clamor95@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change TEGRA_USB_HOSTPC1_DEVLC_PTS_HSIC to its literal value instead of
using the BIT macro, as it is an enumeration. Correct the spelling in the
comment and rename uhsic_registers_shift to uhsic_registers_offset.
These changes are cosmetic and do not affect code behavior.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Link: https://patch.msgid.link/20260202080526.23487-2-clamor95@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for HSIC USB mode, which can be set for second USB controller
and PHY on Tegra SoC along with already supported UTMI or ULPI.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Link: https://patch.msgid.link/20260122151125.7367-3-clamor95@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor to directly use enum usb_phy_interface to determine the PHY mode.
This change is in preparation for adding support for HSIC mode.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Link: https://patch.msgid.link/20260122151125.7367-2-clamor95@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tegra_ehci_phy_restore_start() and tegra_ehci_phy_restore_end()
last use was removed in 2013 by
commit a4faa54e3a ("USB: EHCI: tegra: remove all power management")
tegra_usb_phy_preresume() and tegra_usb_phy_postresume() last
use was removed in 2020 by
commit c3590c7656 ("usb: host: ehci-tegra: Remove the driver")
(Although that one makes me wonder how much of the rest of the file
is actually used)
Remove both sets.
Signed-off-by: "Dr. David Alan Gilbert" <linux@treblig.org>
Link: https://lore.kernel.org/r/20250603203905.279307-1-linux@treblig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/usb to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240924084329.53094-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230718143027.1064731-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230319092428.283054-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230310144728.1545786-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I would like to stop exporting OF-specific devm_gpiod_get_from_of_node()
so that gpiolib can be cleaned a bit, so let's switch to the generic
device property API.
I believe that the only reason the driver, instead of the standard
devm_gpiod_get(), used devm_gpiod_get_from_of_node() is because it
wanted to set up a pretty consumer name for the GPIO, and we now have
a special API for that.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20220903-gpiod_get_from_of_node-remove-v1-4-b29adfb27a6c@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The B_SESS_VLD_WAKEUP_EN bit 6 was added by a mistake in a previous
commit. This bit corresponds to B_SESS_END_WAKEUP_EN, which we don't use.
The B_VBUS_VLD_WAKEUP_EN doesn't exist at all and B_SESS_VLD_WAKEUP_EN
needs to be in place of it. We don't utilize B-sensors in the driver,
so it never was a problem, nevertheless let's correct the definition of
the bits.
Fixes: 35192007d2 ("usb: phy: tegra: Support waking up from a low power mode")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210613145936.9902-2-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices need an extra delay after losing VBUS, otherwise VBUS may
be detected as active at suspend time, preventing the PHY's suspension
by the VBUS detection sensor. This problem was found on Asus Transformer
TF700T (Tegra30) tablet device, where the USB PHY wakes up immediately
from suspend because VBUS sensor continues to detect VBUS as active after
disconnection. We need to poll the PHY's VBUS wakeup status until it's
deasserted before suspending PHY in order to fix this minor trouble.
Fixes: 35192007d2 ("usb: phy: tegra: Support waking up from a low power mode")
Reported-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210613145936.9902-1-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support programming of waking up from a low power mode by implementing the
generic set_wakeup() callback of the USB PHY API.
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201218120246.7759-3-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PHY hardware needs the delay of 2ms after power up, otherwise initial
interrupt may be lost if USB controller is accessed before PHY is settled
down. Previously this issue was masked by implicit delays, but now it pops
up after squashing the older ehci-tegra driver into the ChipIdea driver.
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Ion Agorria <ion@agorria.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201218120246.7759-2-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function tegra_usb_phy_probe(), if usb_add_phy_dev() failed,
the return value will be given to err, and if usb_add_phy_dev() succeed,
the return value will be zero. Thus it is unnecessary to repeated check
here.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The driver uses only GPIO Descriptor Consumer Interface so include
proper header. This fixes compile test failures (e.g. on i386):
drivers/usb/phy/phy-tegra-usb.c: In function ‘ulpi_phy_power_on’:
drivers/usb/phy/phy-tegra-usb.c:695:2: error:
implicit declaration of function ‘gpiod_set_value_cansleep’ [-Werror=implicit-function-declaration]
drivers/usb/phy/phy-tegra-usb.c: In function ‘tegra_usb_phy_probe’:
drivers/usb/phy/phy-tegra-usb.c:1167:11: error:
implicit declaration of function ‘devm_gpiod_get_from_of_node’ [-Werror=implicit-function-declaration]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/1583234960-24909-1-git-send-email-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tools like Coccinelle may erroneously recommend to use the
devm_platform_ioremap_resource() API for the registers mapping because
these tools are not aware about the implementation details of the driver.
Let's add a clarifying comments to the code, which should help to stop
future attempts to break the driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200202224259.29187-1-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no good reason for disabling of CPU interrupts in order to
protect the utmip_pad_count modification.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-17-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's unlikely that two drivers could manage PHY's state simultaneously in
practice, nevertheless the utmip_pad_count checking should be under lock,
for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-16-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is much more intuitive if reset is treated as asserted when GPIO value
is set to 1. All NVIDIA Tegra device-trees are properly specifying active
state of the reset-GPIO since 2013, let's clean up that part of the code.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-14-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a mix of u32/ULONG usage in the driver's code. Let's switch to
u32 uniformly, for consistency.
Suggested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-13-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The resource-managed variant removes the necessity for the driver to care
about freeing ULPI resources.
Suggested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-12-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is nothing to synchronize in regards to memory stores, thus all
readl/writel occurrences in the code could be replaced with a relaxed
versions, for consistency.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-9-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add "spinlock.h", which was included indirectly, and sort includes in
alphabet order.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-8-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes few dozens of legit checkpatch warnings, adds missed
handling of potential error-cases and prettifies code where makes sense.
All these clean-up changes are quite minor and do not fix any real
problems.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-7-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generic PHY provides init/shutdown callbacks which allow USB-host drivers
to abstract PHY's hardware management in a common way. This change allows
to remove Tegra-specific PHY handling from the ChipIdea driver.
Note that ChipIdea's driver shall be changed at the same time because it
turns PHY ON without the PHY's initialization and this doesn't work now,
resulting in a NULL dereference of phy->freq because it's set during of
the PHY's initialization.
Acked-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-6-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PHY driver should keep track of the enable state, otherwise enable
refcount is screwed if USB driver tries to enable PHY when it is already
enabled. This will be the case for ChipIdea and Tegra EHCI drivers once
PHY driver will gain support for the init/shutdown callbacks.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-5-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firstly, the PHY's clock needs to unprepared to keep prepare count
balanced. Secondly, downstream code suggests that reset is synchronous
and thus it should be asserted before disabling clock.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-4-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UTMI pads are shared by USB controllers and reset of UTMI pads is shared
with the reset of USB1 controller. Currently reset of UTMI pads is done by
the EHCI driver and ChipIdea UDC works because EHCI driver always happen
to be probed first. Move reset controls from ehci-tegra to tegra-phy in
order to resolve the problem.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tegra's PHY driver has a mix of pr_err() and dev_err(), let's switch to
dev_err() and use common errors message formatting across the driver for
consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes "utmi_phy_clk_enable: timeout waiting for phy to stabilize"
error message.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit dfebb5f43a ("usb: chipidea: Add support for Tegra20/30/114/124")
added UDC support for Tegra but with UDC support enabled, is was found
that Tegra30, Tegra114 and Tegra124 would hang on entry to suspend.
The hang occurred during the suspend of the USB PHY when the Tegra PHY
driver attempted to disable the PHY clock. The problem is that before
the Tegra PHY driver is suspended, the chipidea driver already disabled
the PHY clock and when the Tegra PHY driver suspended, it could not read
DEVLC register and caused the device to hang.
The Tegra USB PHY driver is used by both the Tegra EHCI driver and now
the chipidea UDC driver and so simply removing the disabling of the PHY
clock from the USB PHY driver would not work for the Tegra EHCI driver.
Fortunately, the status of the USB PHY clock can be read from the
USB_SUSP_CTRL register and therefore, to workaround this issue, simply
poll the register prior to disabling the clock in USB PHY driver to see
if clock gating has already been initiated. Please note that it can take
a few uS for the clock to disable and so simply reading this status
register once on entry is not sufficient.
Similarly when turning on the PHY clock, it is possible that the clock
is already enabled or in the process of being enabled, and so check for
this when enabling the PHY.
Please note that no issues are seen with Tegra20 because it has a slightly
different PHY to Tegra30/114/124.
Fixes: dfebb5f43a ("usb: chipidea: Add support for Tegra20/30/114/124")
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The PHY configuration is stored in an opaque "config" field, but when
allocating the structure, its proper size needs to be known. In the case
of UTMI, the proper structure is tegra_utmip_config of which a local
variable already exists, so we can use that to obtain the size from.
Fixes the following warning from the sparse checker:
drivers/usb/phy/phy-tegra-usb.c:882:17: warning: expression using sizeof(void)
Fixes: 81d5dfe6d8 (usb: phy: tegra: Read UTMIP parameters from device tree)
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aJY4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.17 merge window
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
It is no longer needed and keeping it will break 64-bit ARM builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
tegra_usb_phy_close() is supposed to undo the effects of
tegra_usb_phy_init(). It is also currently added as the USB PHY shutdown
callback, which is wrong, since tegra_usb_phy_init() is only called
during probing wheras the shutdown callback can get called multiple
times. This then leads to warnings about unbalanced regulator_disable if
the EHCI driver is unbound and bound again at runtime.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is no longer needed and keeping it will break 64-bit ARM builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: phy-tegra-usb.c: wrong pointer check for remap UTMI
A wrong pointer was used to test the result of devm_ioremap()
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
