The only supported device type by the Virtual Tape Server is 3490. The
3480 device type was an old physical tape model and doesn't exist
anymore. Remove 3480 from the list and any mention of it.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Quite a few command definitions are either not used or don't exist for
3490 tape devices on Virtual Tape Servers (VTS). Cleanup the list, which
makes it easier to understand what commands are actually implemented by
the driver. The lists below outline the exact reason for the removal.
Description for existing commands are adapted to reflect the removal of
support for old device types.
The following commands don't exist in VTS for 3490 devices and are
unused:
INVALID_00 0x00
DIAG_MODE_SET 0x0B
FORCE_STREAM_CNT 0xEB
LOOP_WRITE_TO_READ 0x8B
MODE_SET_C3 0xC3
MODE_SET_CB 0xCB
MODE_SET_D3 0xD3
NEW_MODE_SET 0xEB
RELEASE 0xD4
REQ_TRK_IN_ERROR 0x1B
RESERVE 0xF4
SET_DIAGNOSE 0x4B
The following command definitions are not used:
CONTROL_ACCESS 0xE3
PERF_SUBSYS_FUNC 0x77
READ_BACKWARD 0x0C
READ_BUFFER 0x12
READ_BUFF_LOG 0x24
READ_CONFIG_DATA 0xFA
READ_DEV_CHAR 0x64
READ_MESSAGE_ID 0x4E
READ_SUBSYS_DATA 0x3E
SENSE_GROUP_ID 0x34
SENSE_ID 0xE4
SET_GROUP_ID 0xAF
SET_INTERFACE_ID 0x73
SET_TAPE_WRITE_IMMED 0xC3
SUSPEND 0x5B
SYNC 0x43
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The LOAD_DISPLAY (LDD) X'9F' is still accepted by the Virtual Tape
Server (VTS) but does not perform any action.
Remove all functions and definitions related to this command.
The tape_34xx_ioctl() function is also removed as it was mainly used to
handle additional ioctl functionality. LOAD_DISPLAY was the only left
case. All other ioctls are handled in tapechar_ioctl().
With LOAD_DISPLAY, the remaining definitions in asm/tape390.h are gone.
Delete the file.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Physical 3590/3592 tape models are not supported anymore for a very long
time. The Virtual Tape Server (VTS) emulates and presents only 3490E
models to the host. This is the only supported model and storage server.
Remove the entire code base for 3590/3592 models as it can be considered
dead code for quite some time already.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The tape device type 3590/3592 and emulated 3490 VTS can handle a block
size of up to 256K bytes. Currently the tape device driver is limited to
a block size of 65535 bytes (64K-1). This limitation stems from the
maximum of 65535 bytes of data that can be transferred with one
Channel-Command Word (CCW).
To work around this limitation data chaining is used which uses several
CCW to transfer an entire 256K block of data. A single CCW holds a
maximum of 65535 bytes of data.
Set MAX_BLOCKSIZE to 262144 (= 256K) to allow for data transfers with
larger block sizes. The read_block() and write_block() discipline
functions calculate the number of CCWs required based on the IDAL buffer
array size that was created for a given block size. If there is more
than one CCW required for the data transfer, the new helper function
tape_ccw_dc_idal() is used to build the data chain accordingly.
The Interruption-Repsonse Block (irb) is added to the tape_request
struct so that the tapechar_read/write() functions can analyze what data
was read or written accordingly.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The count parameter of the read/write_block discipline functions was
never used. Remove it.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
arch/s390/pci/pci_bus.h: zpci_bus_init - only declaration left after
commit 05bc1be6db ("s390/pci: create zPCI bus")
arch/s390/include/asm/gmap.h: gmap_pte_notify - only declaration left
after commit 4be130a084 ("s390/mm: add shadow gmap support")
arch/s390/include/asm/pgalloc.h: rcu_table_freelist_finish - only
declaration left after commit 36409f6353 ("[S390] use generic RCU
page-table freeing code")
arch/s390/include/asm/tlbflush.h: smp_ptlb_all - only declaration left
after commit 5a79859ae0 ("s390: remove 31 bit support")
arch/s390/include/asm/vtimer.h: init_cpu_vtimer - only declaration left
after commit b5f87f15e2 ("s390/idle: consolidate idle functions and
definitions")
arch/s390/include/asm/pci.h: zpci_debug_info - only declaration left
after commit 386aa051fb ("s390/pci: remove per device debug attribute")
arch/s390/include/asm/vdso.h: vdso_alloc_boot_cpu - only declaration
left after commit 4bff8cb545 ("s390: convert to GENERIC_VDSO")
arch/s390/include/asm/smp.h: smp_vcpu_scheduled - only declaration left
after commit 67626fadd2 ("s390: enforce CONFIG_SMP")
arch/s390/kernel/entry.h: restart_call_handler - only declaration left
after commit 8b646bd759 ("[S390] rework smp code")
arch/s390/kernel/entry.h: startup_init_nobss - only declaration left
after commit 2e83e0eb85 ("s390: clean .bss before running uncompressed
kernel")
arch/s390/kernel/entry.h: s390_early_resume - only declaration left after
commit 394216275c ("s390: remove broken hibernate / power management
support")
drivers/s390/char/raw3270.h: raw3270_request_alloc_bootmem - only
declaration left after commit 33403dcfcd ("[S390] 3270 console:
convert from bootmem to slab")
drivers/s390/cio/device.h: ccw_device_schedule_sch_unregister - only
declaration left after commit 37de53bb52 ("[S390] cio: introduce ccw
device todos")
drivers/s390/char/tape.h: tape_hotplug_event - has only declaration
since recorded git history.
drivers/s390/char/tape.h: tape_oper_handler - has only declaration since
recorded git history.
drivers/s390/char/tape.h: tape_noper_handler - has only declaration
since recorded git history.
drivers/s390/char/tape_std.h: tape_std_check_locate - only declaration
left after commit 161beff8f4 ("s390/tape: remove tape block leftovers")
drivers/s390/char/tape_std.h: tape_std_default_handler - has only
declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_unexpect_uchk_handler - has only
declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_irq - has only declaration since
recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery - has only
declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery_has_failed -
has only declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery_succeded - has
only declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery_do_retry - has
only declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery_read_opposite -
has only declaration since recorded git history.
drivers/s390/char/tape_std.h: tape_std_error_recovery_HWBUG - has only
declaration since recorded git history.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix this compile error:
In file included from drivers/s390/char/tape_core.c:29:0:
drivers/s390/char/tape_std.h:103:66: warning: ‘struct request’ declared inside parameter list [enabled by default]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the file name from the comment at top of many files. In most
cases the file name was wrong anyway, so it's rather pointless.
Also unify the IBM copyright statement. We did have a lot of sightly
different statements and wanted to change them one after another
whenever a file gets touched. However that never happened. Instead
people start to take the old/"wrong" statements to use as a template
for new files.
So unify all of them in one go.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Added some changes that where proposed by Andrew Morton. Added 3592 device
type.
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Michael Holzheu <holzheu@de.ibm.com>,
Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
