Enable support for data lane rates between 80-160 Mbps cdns dphy
as mentioned in TRM [0] by setting the pll_opdiv field to 16.
This change enables lower resolutions like 640x480 at 60Hz.
[0]: https://www.ti.com/lit/zip/spruil1
(Table 12-552. DPHY_TX_PLL_CTRL Register Field Descriptions)
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Harikrishna Shenoy <h-shenoy@ti.com>
Link: https://lore.kernel.org/r/20250807052002.717807-1-h-shenoy@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Do read-modify-write so that we re-use the characterized reset value as
specified in TRM [1] to program calibration wait time which defines number
of cycles to wait for after startup state machine is in bandgap enable
state.
This fixes PLL lock timeout error faced while using RPi DSI Panel on TI's
AM62L and J721E SoC since earlier calibration wait time was getting
overwritten to zero value thus failing the PLL to lockup and causing
timeout.
[1] AM62P TRM (Section 14.8.6.3.2.1.1 DPHY_TX_DPHYTX_CMN0_CMN_DIG_TBIT2):
Link: https://www.ti.com/lit/pdf/spruj83
Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-3-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
PLL lockup and O_CMN_READY assertion can only happen after common state
machine gets enabled by programming DPHY_CMN_SSM register, but driver was
polling them before the common state machine was enabled which is
incorrect. This is as per the DPHY initialization sequence as mentioned in
J721E TRM [1] at section "12.7.2.4.1.2.1 Start-up Sequence Timing Diagram".
It shows O_CMN_READY polling at the end after common configuration pin
setup where the common configuration pin setup step enables state machine
as referenced in "Table 12-1533. Common Configuration-Related Setup
mentions state machine"
To fix this :
- Add new function callbacks for polling on PLL lock and O_CMN_READY
assertion.
- As state machine and clocks get enabled in power_on callback only, move
the clock related programming part from configure callback to power_on
callback and poll for the PLL lockup and O_CMN_READY assertion after state
machine gets enabled.
- The configure callback only saves the PLL configuration received from the
client driver which will be applied later on in power_on callback.
- Add checks to ensure configure is called before power_on and state
machine is in disabled state before power_on callback is called.
- Disable state machine in power_off so that client driver can re-configure
the PLL by following up a power_off, configure, power_on sequence.
[1]: https://www.ti.com/lit/zip/spruil1
Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-2-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The code in cdns-dphy has probably been part of a DSI driver in the
past. Remove DSI defines and variables which are not used or do not
actually do anything. Also rename cdns_dsi_get_dphy_pll_cfg() to
cdns_dphy_get_pll_cfg(), i.e. drop the "dsi", as it's not relevant here.
Reviewed-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250723-cdns-dphy-hs-clk-rate-fix-v1-2-d4539d44cbe7@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DPHY driver does not return the actual hs_clk_rate, so the DSI
driver has no idea what clock was actually achieved. Set the realized
hs_clk_rate to the opts struct, so that the DSI driver gets it back.
Reviewed-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Tested-by: Jayesh Choudhary <j-choudhary@ti.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250723-cdns-dphy-hs-clk-rate-fix-v1-1-d4539d44cbe7@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/phy/ to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
While touching these files, make indention of the struct initializer
consistent in several files.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241009065307.504930-2-u.kleine-koenig@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/phy/phy-can-transceiver.c
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20230714174841.4061919-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230307115900.2293120-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support new compatible for dphy-tx on j721e
and implement dphy ops required.
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220623125433.18467-4-r-ravikumar@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cadence has designed a D-PHY that can be used by the, currently in tree,
DSI bridge (DRM), CSI Transceiver and CSI Receiver (v4l2) drivers.
Only the DSI driver has an ad-hoc driver for that phy at the moment, while
the v4l2 drivers are completely missing any phy support. In order to make
that phy support available to all these drivers, without having to
duplicate that code three times, let's create a generic phy framework
driver.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
