The TRENDnet TUC-ET2G V2.0 is an RTL8156B based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Birger Koblitz <mail@birger-koblitz.de>
Link: https://patch.msgid.link/20260430213435.21821-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RTL8157 uses a different packet descriptor format compared to the
previous generation of chips. Add support for this format by adding a
descriptor format structure into the r8152 structure and corresponding
desc_ops functions which abstract the vlan-tag, tx/rx len and
tx/rx checksum algorithms.
Also, add support for the ADV indirect access interface of the RTL8157
and PHY setup.
For initialization of the RTL8157, combine the existing RTL8156B and
RTL8156 init functions and add RTL8157-specific functinality in order
to improve code readability and maintainability.
r8156_init() is now called with RTL_VER_10 and RTL_VER_11 for the RTL8156,
with RTL_VER_12, RTL_VER_13 and RTL_VER_15 for the RTL8156B and with
RTL_VER_16 for the RTL8157 and checks the version for chip-specific code.
Also add USB power control functions for the RTL8157.
Add support for the USB device ID of Realtek RTL8157-based adapters. Detect
the RTL8157 as RTL_VER_16 and set it up.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Link: https://patch.msgid.link/20260404-rtl8157_next-v7-2-039121318f23@birger-koblitz.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The RTL8157 supports 5GBit Link speeds. Add support for this speed
in the setup and setting/getting through ethtool. Also add 5GBit EEE.
Add functionality for setup and ethtool get/set methods.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Link: https://patch.msgid.link/20260404-rtl8157_next-v7-1-039121318f23@birger-koblitz.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add the following helper functions for SRAM2 access to simplify the code
and improve readability:
- sram2_write() - write data to SRAM2 address
- sram2_read() - read data from SRAM2 address
- sram2_write_w0w1() - read-modify-write operation
Signed-off-by: Chih Kai Hsu <hsu.chih.kai@realtek.com>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20260401115542.34601-1-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the following bitwise operation functions for PHY OCP registers to
simplify the code.
- ocp_reg_w0w1()
- ocp_reg_clr_bits()
- ocp_reg_set_bits()
- sram_write_w0w1()
- sram_clr_bits()
- sram_set_bits()
- r8152_mdio_clr_bit()
- r8152_mdio_set_bit()
- r8152_mdio_test_and_clr_bit()
In addition, remove variable set but not used from r8153_init(),
r8153b_init() and r8153c_init().
Signed-off-by: Chih Kai Hsu <hsu.chih.kai@realtek.com>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20260326073925.32976-456-nic_swsd@realtek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The old code used ocp_write_byte() to clear the OOBS_POLLING bit
(BIT(8)) in the USB_UPHY_XTAL register, but this doesn't correctly
clear a bit in the upper byte of the 16-bit register.
Fix this by using ocp_write_word() instead.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Chih Kai Hsu <hsu.chih.kai@realtek.com>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20260326073925.32976-454-nic_swsd@realtek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Cross-merge networking fixes after downstream PR (net-7.0-rc3).
No conflicts.
Adjacent changes:
net/netfilter/nft_set_rbtree.c
fb7fb40163 ("netfilter: nf_tables: clone set on flush only")
3aea466a43 ("netfilter: nft_set_rbtree: don't disable bh when acquiring tree lock")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TRENDnet TUC-ET2G is a RTL8156 based usb ethernet adapter. Add its
vendor and product IDs.
Signed-off-by: Valentin Spreckels <valentin@spreckels.dev>
Link: https://patch.msgid.link/20260226195409.7891-2-valentin@spreckels.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The r8152 driver supports the RTL8156, which is a 2.5Gbit Ethernet controller for
USB 3.0, for which support is added for configuring and displaying the EEE
advertisement status for 2.5GBit connections.
The patch also corrects the determination of whether EEE is active to include
the 2.5GBit connection status and make the determination dependent not on the
desired speed configuration (tp->speed), but on the actual speed used by
the controller. For consistency, this is corrected also for the RTL8152/3.
This was tested on an Edimax EU-4307 V1.0 USB-Ethernet adapter with RTL8156,
and a SECOMP Value 12.99.1115 USB-C 3.1 Ethernet converter with RTL8153.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Link: https://patch.msgid.link/20260224-b4-eee2g5-v2-1-cf5c83df036e@birger-koblitz.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
Total patches: 107
Reviews/patch: 1.07
Reviewed rate: 67%
- The 2 patch series "ocfs2: give ocfs2 the ability to reclaim
suballocator free bg" from Heming Zhao saves disk space by teaching
ocfs2 to reclaim suballocator block group space.
- The 4 patch series "Add ARRAY_END(), and use it to fix off-by-one
bugs" from Alejandro Colomar adds the ARRAY_END() macro and uses it in
various places.
- The 2 patch series "vmcoreinfo: support VMCOREINFO_BYTES larger than
PAGE_SIZE" from Pnina Feder makes the vmcore code future-safe, if
VMCOREINFO_BYTES ever exceeds the page size.
- The 7 patch series "kallsyms: Prevent invalid access when showing
module buildid" from Petr Mladek cleans up kallsyms code related to
module buildid and fixes an invalid access crash when printing
backtraces.
- The 3 patch series "Address page fault in
ima_restore_measurement_list()" from Harshit Mogalapalli fixes a
kexec-related crash that can occur when booting the second-stage kernel
on x86.
- The 6 patch series "kho: ABI headers and Documentation updates" from
Mike Rapoport updates the kexec handover ABI documentation.
- The 4 patch series "Align atomic storage" from Finn Thain adds the
__aligned attribute to atomic_t and atomic64_t definitions to get
natural alignment of both types on csky, m68k, microblaze, nios2,
openrisc and sh.
- The 2 patch series "kho: clean up page initialization logic" from
Pratyush Yadav simplifies the page initialization logic in
kho_restore_page().
- The 6 patch series "Unload linux/kernel.h" from Yury Norov moves
several things out of kernel.h and into more appropriate places.
- The 7 patch series "don't abuse task_struct.group_leader" from Oleg
Nesterov removes the usage of ->group_leader when it is "obviously
unnecessary".
- The 5 patch series "list private v2 & luo flb" from Pasha Tatashin
adds some infrastructure improvements to the live update orchestrator.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCaY4giAAKCRDdBJ7gKXxA
jgusAQDnKkP8UWTqXPC1jI+OrDJGU5ciAx8lzLeBVqMKzoYk9AD/TlhT2Nlx+Ef6
0HCUHUD0FMvAw/7/Dfc6ZKxwBEIxyww=
=mmsH
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2026-02-12-10-48' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
- "ocfs2: give ocfs2 the ability to reclaim suballocator free bg" saves
disk space by teaching ocfs2 to reclaim suballocator block group
space (Heming Zhao)
- "Add ARRAY_END(), and use it to fix off-by-one bugs" adds the
ARRAY_END() macro and uses it in various places (Alejandro Colomar)
- "vmcoreinfo: support VMCOREINFO_BYTES larger than PAGE_SIZE" makes
the vmcore code future-safe, if VMCOREINFO_BYTES ever exceeds the
page size (Pnina Feder)
- "kallsyms: Prevent invalid access when showing module buildid" cleans
up kallsyms code related to module buildid and fixes an invalid
access crash when printing backtraces (Petr Mladek)
- "Address page fault in ima_restore_measurement_list()" fixes a
kexec-related crash that can occur when booting the second-stage
kernel on x86 (Harshit Mogalapalli)
- "kho: ABI headers and Documentation updates" updates the kexec
handover ABI documentation (Mike Rapoport)
- "Align atomic storage" adds the __aligned attribute to atomic_t and
atomic64_t definitions to get natural alignment of both types on
csky, m68k, microblaze, nios2, openrisc and sh (Finn Thain)
- "kho: clean up page initialization logic" simplifies the page
initialization logic in kho_restore_page() (Pratyush Yadav)
- "Unload linux/kernel.h" moves several things out of kernel.h and into
more appropriate places (Yury Norov)
- "don't abuse task_struct.group_leader" removes the usage of
->group_leader when it is "obviously unnecessary" (Oleg Nesterov)
- "list private v2 & luo flb" adds some infrastructure improvements to
the live update orchestrator (Pasha Tatashin)
* tag 'mm-nonmm-stable-2026-02-12-10-48' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (107 commits)
watchdog/hardlockup: simplify perf event probe and remove per-cpu dependency
procfs: fix missing RCU protection when reading real_parent in do_task_stat()
watchdog/softlockup: fix sample ring index wrap in need_counting_irqs()
kcsan, compiler_types: avoid duplicate type issues in BPF Type Format
kho: fix doc for kho_restore_pages()
tests/liveupdate: add in-kernel liveupdate test
liveupdate: luo_flb: introduce File-Lifecycle-Bound global state
liveupdate: luo_file: Use private list
list: add kunit test for private list primitives
list: add primitives for private list manipulations
delayacct: fix uapi timespec64 definition
panic: add panic_force_cpu= parameter to redirect panic to a specific CPU
netclassid: use thread_group_leader(p) in update_classid_task()
RDMA/umem: don't abuse current->group_leader
drm/pan*: don't abuse current->group_leader
drm/amd: kill the outdated "Only the pthreads threading model is supported" checks
drm/amdgpu: don't abuse current->group_leader
android/binder: use same_thread_group(proc->tsk, current) in binder_mmap()
android/binder: don't abuse current->group_leader
kho: skip memoryless NUMA nodes when reserving scratch areas
...
rtl8152 can trigger device reset during reset which
potentially can result in a deadlock:
**** DPM device timeout after 10 seconds; 15 seconds until panic ****
Call Trace:
<TASK>
schedule+0x483/0x1370
schedule_preempt_disabled+0x15/0x30
__mutex_lock_common+0x1fd/0x470
__rtl8152_set_mac_address+0x80/0x1f0
dev_set_mac_address+0x7f/0x150
rtl8152_post_reset+0x72/0x150
usb_reset_device+0x1d0/0x220
rtl8152_resume+0x99/0xc0
usb_resume_interface+0x3e/0xc0
usb_resume_both+0x104/0x150
usb_resume+0x22/0x110
The problem is that rtl8152 resume calls reset under
tp->control mutex while reset basically re-enters rtl8152
and attempts to acquire the same tp->control lock once
again.
Reset INACCESSIBLE device outside of tp->control mutex
scope to avoid recursive mutex_lock() deadlock.
Fixes: 4933b066fe ("r8152: If inaccessible at resume time, issue a reset")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Link: https://patch.msgid.link/20260129031106.3805887-1-senozhatsky@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Many USB network drivers define get_drvinfo functions which add no
value over usbnet_get_drvinfo, only setting the driver name and
version. usbnet_get_drvinfo automatically sets the driver name, and
separate driver versions are now frowned upon in the kernel. Remove all
driver versions and replace these get_drvinfo functions with references
to usbnet_get_drvinfo where possible. Where that is not possible,
remove unnecessary code to set the driver name. Also remove two
unnecessary initializations from aqc111_get_drvinfo, an inaccurate
comment in pegasus.c, and an unused macro in catc.c.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com> (for dm9601.c)
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Link: https://patch.msgid.link/20260129042435.13395-2-enelsonmoore@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove <linux/hex.h> from <linux/kernel.h> and update all users/callers of
hex.h interfaces to directly #include <linux/hex.h> as part of the process
of putting kernel.h on a diet.
Removing hex.h from kernel.h means that 36K C source files don't have to
pay the price of parsing hex.h for the roughly 120 C source files that
need it.
This change has been build-tested with allmodconfig on most ARCHes. Also,
all users/callers of <linux/hex.h> in the entire source tree have been
updated if needed (if not already #included).
Link: https://lkml.kernel.org/r/20251215005206.2362276-1-rdunlap@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Yury Norov (NVIDIA) <yury.norov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When the TX queue length reaches the threshold, the netdev watchdog
immediately detects a TX queue timeout.
This patch updates the trans_start timestamp of the transmit queue
on every asynchronous USB URB submission along the transmit path,
ensuring that the network watchdog accurately reflects ongoing
transmission activity.
Signed-off-by: Mingj Ye <insyelu@gmail.com>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20260120015949.84996-1-insyelu@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Driver calls skb_tx_timestamp(skb) in rtl8152_start_xmit(), but does not advertise the capability in ethtool.
Advertise software timestamp capabilities on struct ethtool_ops.
Signed-off-by: Abhishek Rawal <rawal.abhishek92@gmail.com>
Reviewed-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251014055234.46527-1-rawal.abhishek92@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rtl8152_driver_init() is missing the error handling.
When rtl8152_driver registration fails, rtl8152_cfgselector_driver
should be deregistered.
Fixes: ec51fbd1b8 ("r8152: add USB device driver for config selection")
Cc: stable@vger.kernel.org
Signed-off-by: Yi Cong <yicong@kylinos.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251011082415.580740-1-yicongsrfy@163.com
[pabeni@redhat.com: clarified the commit message]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The TP-Link UE200 is a RTL8152B based USB 2.0 Fast Ethernet adapter. This
patch adds its device ID. It has been tested on Ubuntu 22.04.5.
Signed-off-by: Lucas Sanchez Sagrado <lucsansag@gmail.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://patch.msgid.link/20250609145536.26648-1-lucsansag@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All users of dev_set_mac_address() are now using a struct sockaddr_storage.
Convert the internal data type to struct sockaddr_storage, drop the casts,
and update pointer types.
Acked-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://patch.msgid.link/20250521204619.2301870-6-kees@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
To support coming API type changes, switch to sockaddr_storage usage
internally.
Acked-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://patch.msgid.link/20250521204619.2301870-5-kees@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This user of SHA-256 does not support any other algorithm, so the
crypto_shash abstraction provides no value. Just use the SHA-256
library API instead, which is much simpler and easier to use.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://patch.msgid.link/20250428191606.856198-1-ebiggers@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lenovo ThinkPad Hybrid USB-C with USB-A Dock (17ef:a359) is affected by
the same problem as the Lenovo Powered USB-C Travel Hub (17ef:721e):
Both are based on the Realtek RTL8153B chip used to use the cdc_ether
driver. However, using this driver, with the system suspended the device
constantly sends pause-frames as soon as the receive buffer fills up.
This causes issues with other devices, where some Ethernet switches stop
forwarding packets altogether.
Using the Realtek driver (r8152) fixes this issue. Pause frames are no
longer sent while the host system is suspended.
Cc: Leon Schuermann <leon@is.currently.online>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Oliver Neukum <oliver@neukum.org> (maintainer:USB CDC ETHERNET DRIVER)
Cc: netdev@vger.kernel.org (open list:NETWORKING DRIVERS)
Link: https://git.kernel.org/netdev/net/c/cb82a54904a9
Link: https://git.kernel.org/netdev/net/c/2284bbd0cf39
Link: https://www.lenovo.com/de/de/p/accessories-and-software/docking/docking-usb-docks/40af0135eu
Signed-off-by: Philipp Hahn <phahn-oss@avm.de>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/484336aad52d14ccf061b535bc19ef6396ef5120.1741601523.git.p.hahn@avm.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The Dell AW1022z is an RTL8156B based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://patch.msgid.link/20250206224033.980115-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support for another Lenovo Mini dock 0x17EF:0x3098 to the
r8152 driver. The device has been tested on NixOS, hotplugging and sleep
included.
Signed-off-by: Benjamin Große <ste3ls@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241020174128.160898-1-ste3ls@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
generic_ocp_write() asks the parameter "size" must be 4 bytes align.
Therefore, write the bp would fail, if the mac->bp_num is odd. Align the
size to 4 for fixing it. The way may write an extra bp, but the
rtl8152_is_fw_mac_ok() makes sure the value must be 0 for the bp whose
index is more than mac->bp_num. That is, there is no influence for the
firmware.
Besides, I check the return value of generic_ocp_write() to make sure
everything is correct.
Fixes: e5c266a611 ("r8152: set bp in bulk")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20240903063333.4502-1-hayeswang@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some docks support MAC pass-through - MAC address
is taken from another device.
Driver should indicate that with NET_ADDR_STOLEN flag.
This should help to avoid collisions if network interface
names are generated with MAC policy.
Reported and discussed here
https://github.com/systemd/systemd/issues/33104
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240605153340.25694-1-gmazyland@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we get to the end of the r8152's suspend() routine and we find that
the USB device is INACCESSIBLE then it means that some of our
preparation for suspend didn't take place. We need a USB reset to get
ourselves back in a consistent state so we can try again and that
can't happen during system suspend. Call pm_wakeup_event() to wake the
system up in this case.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/66590f25.170a0220.8b5ad.1752@mx.google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we happened to get a USB transfer error during the transition to
suspend then the usb_queue_reset_device() that r8152_control_msg()
calls will get dropped on the floor. This is because
usb_lock_device_for_reset() (which usb_queue_reset_device() uses)
silently fails if it's called when a device is suspended or if too
much time passes.
Let's resolve this by resetting the device ourselves in r8152's
resume() function.
NOTE: due to timing, it's _possible_ that we could end up with two USB
resets: the one queued previously and the one called from the resume()
patch. This didn't happen in test cases I ran, though it's conceivably
possible. We can't easily know if this happened since
usb_queue_reset_device() can just silently drop the reset request. In
any case, it's not expected that this is a problem since the two
resets can't run at the same time (because of the device lock) and it
should be OK to reset the device twice. If somehow the double-reset
causes problems we could prevent resets from being queued up while
suspend is running.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/66590f22.170a0220.8b5ad.1750@mx.google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c945 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Someone complains the message appears continuously. This occurs
because the device is woken from UPS mode, and the driver re-loads
the firmware.
When the device enters runtime suspend and cable is unplugged, the
device would enter UPS mode. If the runtime resume occurs, and the
device is woken from UPS mode, the driver has to re-load the firmware
and causes the message. If someone wakes the device continuously, the
message would be shown continuously, too. Use dev_dbg to avoid it.
Note that, the function could be called before register_netdev(), so I
don't use netif_info() or netif_dbg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20240424084532.159649-1-hayeswang@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For the unknown device, rtl8152_cfgselector_choose_configuration()
should return a negative value. Then, usb_choose_configuration() would
set a configuration for CDC ECM or NCM mode. Otherwise, there is no
usb interface driver for the device.
Fixes: aa4f2b3e41 ("r8152: Choose our USB config with choose_configuration() rather than probe()")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20240308075206.33553-436-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make use of the existing linkmode helpers for converting PHY EEE
register values into links modes, now that ethtool_keee uses link
modes, rather than u32 values.
Rework determining if EEE is active to make is similar as to how
phylib decides, and make use of a phylib helper to validate if EEE is
valid in for the current link mode. This then requires that PHYLIB is
selected.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in preparation of using the existing names for linkmode
bitmaps.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ASUS USB-C2500 is an RTL8156 based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Kelly Kane <kelly@hawknetworks.com>
Link: https://lore.kernel.org/r/20231203011712.6314-1-kelly@hawknetworks.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If you deauthorize the r8152 device (by writing 0 to the "authorized"
field in sysfs) and then reauthorize it (by writing a 1) then it no
longer works. This is because when you do the above we lose the
special configuration that we set in rtl8152_cfgselector_probe().
Deauthorizing causes the config to be set to -1 and then reauthorizing
runs the default logic for choosing the best config.
I made an attempt to fix it so that the config is kept across
deauthorizing / reauthorizing [1] but it was a bit ugly.
Let's instead use the new USB core feature to override
choose_configuration().
This patch relies upon the patches ("usb: core: Don't force USB
generic_subclass drivers to define probe()") and ("usb: core: Allow
subclassed USB drivers to override usb_choose_configuration()")
[1] https://lore.kernel.org/r/20231130154337.1.Ie00e07f07f87149c9ce0b27ae4e26991d307e14b@changeid
Fixes: ec51fbd1b8 ("r8152: add USB device driver for config selection")
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Link: https://lore.kernel.org/r/20231201102946.v2.3.Ie00e07f07f87149c9ce0b27ae4e26991d307e14b@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in r8153_aldps_en().
Fixes: 4214cc550b ("r8152: check if disabling ALDPS is finished")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in r8153_pre_firmware_1().
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in
r8156b_wait_loading_flash().
Fixes: 195aae321c ("r8152: support new chips")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous commits added checks for RTL8152_INACCESSIBLE in the loops in
the driver. There are still a few more that keep tripping the driver
up in error cases and make things take longer than they should. Add
those in.
All the loops that are part of this commit existed in some form or
another since the r8152 driver was first introduced, though
RTL8152_INACCESSIBLE was known as RTL8152_UNPLUG before commit
715f67f33a ("r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE")
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit d9962b0d42 ("r8152: Block future register access if
register access fails") there is a race condition that can happen
between the USB device reset thread and napi_enable() (not) getting
called during rtl8152_open(). Specifically:
* While rtl8152_open() is running we get a register access error
that's _not_ -ENODEV and queue up a USB reset.
* rtl8152_open() exits before calling napi_enable() due to any reason
(including usb_submit_urb() returning an error).
In that case:
* Since the USB reset is perform in a separate thread asynchronously,
it can run at anytime USB device lock is not held - even before
rtl8152_open() has exited with an error and caused __dev_open() to
clear the __LINK_STATE_START bit.
* The rtl8152_pre_reset() will notice that the netif_running() returns
true (since __LINK_STATE_START wasn't cleared) so it won't exit
early.
* rtl8152_pre_reset() will then hang in napi_disable() because
napi_enable() was never called.
We can fix the race by making sure that the r8152 reset routines don't
run at the same time as we're opening the device. Specifically we need
the reset routines in their entirety rely on the return value of
netif_running(). The only way to reliably depend on that is for them
to hold the rntl_lock() mutex for the duration of reset.
Grabbing the rntl_lock() mutex for the duration of reset seems like a
long time, but reset is not expected to be common and the rtnl_lock()
mutex is already held for long durations since the core grabs it
around the open/close calls.
Fixes: d9962b0d42 ("r8152: Block future register access if register access fails")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though the functions to read/write registers can fail, most of
the places in the r8152 driver that read/write register values don't
check error codes. The lack of error code checking is problematic in
at least two ways.
The first problem is that the r8152 driver often uses code patterns
similar to this:
x = read_register()
x = x | SOME_BIT;
write_register(x);
...with the above pattern, if the read_register() fails and returns
garbage then we'll end up trying to write modified garbage back to the
Realtek adapter. If the write_register() succeeds that's bad. Note
that as of commit f53a7ad189 ("r8152: Set memory to all 0xFFs on
failed reg reads") the "garbage" returned by read_register() will at
least be consistent garbage, but it is still garbage.
It turns out that this problem is very serious. Writing garbage to
some of the hardware registers on the Ethernet adapter can put the
adapter in such a bad state that it needs to be power cycled (fully
unplugged and plugged in again) before it can enumerate again.
The second problem is that the r8152 driver generally has functions
that are long sequences of register writes. Assuming everything will
be OK if a random register write fails in the middle isn't a great
assumption.
One might wonder if the above two problems are real. You could ask if
we would really have a successful write after a failed read. It turns
out that the answer appears to be "yes, this can happen". In fact,
we've seen at least two distinct failure modes where this happens.
On a sc7180-trogdor Chromebook if you drop into kdb for a while and
then resume, you can see:
1. We get a "Tx timeout"
2. The "Tx timeout" queues up a USB reset.
3. In rtl8152_pre_reset() we try to reinit the hardware.
4. The first several (2-9) register accesses fail with a timeout, then
things recover.
The above test case was actually fixed by the patch ("r8152: Increase
USB control msg timeout to 5000ms as per spec") but at least shows
that we really can see successful calls after failed ones.
On a different (AMD) based Chromebook with a particular adapter, we
found that during reboot tests we'd also sometimes get a transitory
failure. In this case we saw -EPIPE being returned sometimes. Retrying
worked, but retrying is not always safe for all register accesses
since reading/writing some registers might have side effects (like
registers that clear on read).
Let's fully lock out all register access if a register access fails.
When we do this, we'll try to queue up a USB reset and try to unlock
register access after the reset. This is slightly tricker than it
sounds since the r8152 driver has an optimized reset sequence that
only works reliably after probe happens. In order to handle this, we
avoid the optimized reset if probe didn't finish. Instead, we simply
retry the probe routine in this case.
When locking out access, we'll use the existing infrastructure that
the driver was using when it detected we were unplugged. This keeps us
from getting stuck in delay loops in some parts of the driver.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever the RTL8152_UNPLUG is set that just tells the driver that all
accesses will fail and we should just immediately bail. A future patch
will use this same concept at a time when the driver hasn't actually
been unplugged but is about to be reset. Rename the flag in
preparation for the future patch.
This is a no-op change and just a search and replace.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
