phy_advertise_eee_all() copies supported_eee into advertising_eee
unconditionally, overwriting any filtering applied during phy_probe()
based on DT eee-broken-* properties or driver-populated
eee_disabled_modes. genphy_c45_ethtool_set_eee() calls this helper
when user space passes an empty advertisement, undoing the filtering.
Apply the same eee_disabled_modes mask in phy_advertise_eee_all() so
the filtering survives the copy, matching the pattern in phy_probe()
and phy_support_eee().
Fixes: b64691274f ("net: phy: add helper phy_advertise_eee_all")
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260518-devel-phy-support-eee-fix-v2-2-05b52626fa68@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
phy_support_eee() copies supported_eee into advertising_eee
unconditionally, overwriting any filtering applied during phy_probe()
based on DT eee-broken-* properties or driver-populated
eee_disabled_modes. MAC drivers that call phy_support_eee() after
probe (e.g. bcmgenet, fec, lan743x, lan78xx, r8169) then cause the PHY
to advertise EEE for modes the user marked as broken.
The symptom is that ethtool --show-eee on the local interface reports
"not supported" (supported & ~eee_disabled_modes is empty) while the
link partner sees EEE negotiated and active.
phy_probe() already filters advertising_eee via eee_disabled_modes
after calling of_set_phy_eee_broken(). Apply the same mask in
phy_support_eee() so the filtering survives the copy.
Fixes: 49168d1980 ("net: phy: Add phy_support_eee() indicating MAC support EEE")
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260518-devel-phy-support-eee-fix-v2-1-05b52626fa68@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge in late fixes in preparation for the net-next PR.
Conflicts:
include/net/sch_generic.h
a6bd339dbb ("net_sched: fix skb memory leak in deferred qdisc drops")
ff2998f29f ("net: sched: introduce qdisc-specific drop reason tracing")
https://lore.kernel.org/adz0iX85FHMz0HdO@sirena.org.uk
drivers/net/ethernet/airoha/airoha_eth.c
1acdfbdb51 ("net: airoha: Fix VIP configuration for AN7583 SoC")
bf3471e6e6 ("net: airoha: Make flow control source port mapping dependent on nbq parameter")
Adjacent changes:
drivers/net/ethernet/airoha/airoha_ppe.c
f44218cd5e ("net: airoha: Reset PPE cpu port configuration in airoha_ppe_hw_init()")
7da62262ec ("inet: add ip_local_port_step_width sysctl to improve port usage distribution")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The return value of phy_c45_probe_present() is stored in "ret", not
"phy_reg", fix this. "phy_reg" always has a positive value if we reach
this return path (since it would have returned earlier otherwise), which
means that the original goal of the patch of not considering -ENODEV
fatal wasn't achieved.
Fixes: 17b4475394 ("net: phy: c45 scanning: Don't consider -ENODEV fatal")
Signed-off-by: Charles Perry <charles.perry@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260409133654.3203336-1-charles.perry@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some PHYs (e.g. Broadcom BCM54xx, Realtek RTL8211F) implement
autonomous EEE where the PHY manages LPI signaling without forwarding
it to the MAC. This conflicts with MAC drivers that implement their own
LPI control.
Add a .disable_autonomous_eee callback to struct phy_driver and call it
from phy_support_eee(). When a MAC driver indicates it supports EEE via
phy_support_eee(), the PHY's autonomous EEE is automatically disabled so
the MAC can manage LPI entry/exit.
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260406-devel-autonomous-eee-v1-1-b335e7143711@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is an AB-BA deadlock when both LEDS_TRIGGER_NETDEV and
LED_TRIGGER_PHY are enabled:
[ 1362.049207] [<8054e4b8>] led_trigger_register+0x5c/0x1fc <-- Trying to get lock "triggers_list_lock" via down_write(&triggers_list_lock);
[ 1362.054536] [<80662830>] phy_led_triggers_register+0xd0/0x234
[ 1362.060329] [<8065e200>] phy_attach_direct+0x33c/0x40c
[ 1362.065489] [<80651fc4>] phylink_fwnode_phy_connect+0x15c/0x23c
[ 1362.071480] [<8066ee18>] mtk_open+0x7c/0xba0
[ 1362.075849] [<806d714c>] __dev_open+0x280/0x2b0
[ 1362.080384] [<806d7668>] __dev_change_flags+0x244/0x24c
[ 1362.085598] [<806d7698>] dev_change_flags+0x28/0x78
[ 1362.090528] [<807150e4>] dev_ioctl+0x4c0/0x654 <-- Hold lock "rtnl_mutex" by calling rtnl_lock();
[ 1362.094985] [<80694360>] sock_ioctl+0x2f4/0x4e0
[ 1362.099567] [<802e9c4c>] sys_ioctl+0x32c/0xd8c
[ 1362.104022] [<80014504>] syscall_common+0x34/0x58
Here LED_TRIGGER_PHY is registering LED triggers during phy_attach
while holding RTNL and then taking triggers_list_lock.
[ 1362.191101] [<806c2640>] register_netdevice_notifier+0x60/0x168 <-- Trying to get lock "rtnl_mutex" via rtnl_lock();
[ 1362.197073] [<805504ac>] netdev_trig_activate+0x194/0x1e4
[ 1362.202490] [<8054e28c>] led_trigger_set+0x1d4/0x360 <-- Hold lock "triggers_list_lock" by down_read(&triggers_list_lock);
[ 1362.207511] [<8054eb38>] led_trigger_write+0xd8/0x14c
[ 1362.212566] [<80381d98>] sysfs_kf_bin_write+0x80/0xbc
[ 1362.217688] [<8037fcd8>] kernfs_fop_write_iter+0x17c/0x28c
[ 1362.223174] [<802cbd70>] vfs_write+0x21c/0x3c4
[ 1362.227712] [<802cc0c4>] ksys_write+0x78/0x12c
[ 1362.232164] [<80014504>] syscall_common+0x34/0x58
Here LEDS_TRIGGER_NETDEV is being enabled on an LED. It first takes
triggers_list_lock and then RTNL. A classical AB-BA deadlock.
phy_led_triggers_registers() does not require the RTNL, it does not
make any calls into the network stack which require protection. There
is also no requirement the PHY has been attached to a MAC, the
triggers only make use of phydev state. This allows the call to
phy_led_triggers_registers() to be placed elsewhere. PHY probe() and
release() don't hold RTNL, so solving the AB-BA deadlock.
Reported-by: Shiji Yang <yangshiji66@outlook.com>
Closes: https://lore.kernel.org/all/OS7PR01MB13602B128BA1AD3FA38B6D1FFBC69A@OS7PR01MB13602.jpnprd01.prod.outlook.com/
Fixes: 06f502f57d ("leds: trigger: Introduce a NETDEV trigger")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://patch.msgid.link/20260222152601.1978655-1-andrew@lunn.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
With the phy_port infrastructure came an ethernet-connector binding,
allowing to represent the MDI of a PHY in devicetree. This allows
specifying the mediums and pairs of a port.
Let's initialize the port's supported list based on what the PHY
reports, so that we can then filter it with what the connector allows
using.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Christophe Leroy (CS GROUP) <chleroy@kernel.org>
Link: https://patch.msgid.link/20260205092317.755906-2-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enhance the grammar of the comment in genphy_update_link()
describing momentary link drop handling.
Found by inspection.
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260121-phy-gra-v1-1-8b4d178939de@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Based on the fact that either bus_id-based matching or phy_uid-based
matching is used, the code can be simplified. PHY_ANY_ID and
PHY_ANY_UID are not needed. Ensure that phy_id_compare() is called
only if phy_uid_mask isn't zero, because a zero value would always
result in a match.
In addition change the return value type of phy_needs_fixup() to bool.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/e7394cc8-5895-4d02-a8fe-802345c7c547@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
No user of PHY fixups unregisters these. IOW: The fixup unregistering
functions are unused and can be removed. Remove also documentation
for these functions. Whilst at it, remove also mentioning of
phy_register_fixup() from the Documentation, as this function has been
static since ea47e70e47 ("net: phy: remove fixup-related definitions
from phy.h which are not used outside phylib").
Fixup unregistering functions were added with f38e7a32ee
("phy: add phy fixup unregister functions") in 2016, and last user
was removed with 6782d06a47 ("net: usb: lan78xx: Remove KSZ9031 PHY
fixup") in 2024.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/ff8ac321-435c-48d0-b376-fbca80c0c22e@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that all PHY drivers that support downstream SFP have been converted
to phy_port serdes handling, we can make the generic PHY SFP handling
mandatory, thus making all phylib sfp helpers static.
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260108080041.553250-14-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are currently 4 PHY drivers that can drive downstream SFPs:
marvell.c, marvell10g.c, at803x.c and marvell-88x2222.c. Most of the
logic is boilerplate, either calling into generic phylib helpers (for
SFP PHY attach, bus attach, etc.) or performing the same tasks with a
bit of validation :
- Getting the module's expected interface mode
- Making sure the PHY supports it
- Optionaly perform some configuration to make sure the PHY outputs
the right mode
This can be made more generic by leveraging the phy_port, and its
configure_mii() callback which allows setting a port's interfaces when
the port is a serdes.
Introduce a generic PHY SFP support. If a driver doesn't probe the SFP
bus itself, but an SFP phandle is found in devicetree/firmware, then the
generic PHY SFP support will be used, relying on port ops.
PHY driver need to :
- Register a .attach_port() callback
- When a serdes port is registered to the PHY, drivers must set
port->interfaces to the set of PHY_INTERFACE_MODE the port can output
- If the port has limitations regarding speed, duplex and aneg, the
port can also fine-tune the final linkmodes that can be supported
- The port may register a set of ops, including .configure_mii(), that
will be called at module_insert time to adjust the interface based on
the module detected.
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260108080041.553250-8-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some PHY devices may be used as media-converters to drive SFP ports (for
example, to allow using SFP when the SoC can only output RGMII). This is
already supported to some extend by allowing PHY drivers to registers
themselves as being SFP upstream.
However, the logic to drive the SFP can actually be split to a per-port
control logic, allowing support for multi-port PHYs, or PHYs that can
either drive SFPs or Copper.
To that extent, create a phy_port when registering an SFP bus onto a
PHY. This port is considered a "serdes" port, in that it can feed data
to another entity on the link. The PHY driver needs to specify the
various PHY_INTERFACE_MODE_XXX that this port supports.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260108080041.553250-7-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ethernet provides a wide variety of layer 1 protocols and standards for
data transmission. The front-facing ports of an interface have their own
complexity and configurability.
Introduce a representation of these front-facing ports. The current code
is minimalistic and only support ports controlled by PHY devices, but
the plan is to extend that to SFP as well as raw Ethernet MACs that
don't use PHY devices.
This minimal port representation allows describing the media and number
of pairs of a BaseT port. From that information, we can derive the
linkmodes usable on the port, which can be used to limit the
capabilities of an interface.
For now, the port pairs and medium is derived from devicetree, defined
by the PHY driver, or populated with default values (as we assume that
all PHYs expose at least one port).
The typical example is 100M ethernet. 100BaseTX works using only 2
pairs on a Cat 5 cables. However, in the situation where a 10/100/1000
capable PHY is wired to its RJ45 port through 2 pairs only, we have no
way of detecting that. The "max-speed" DT property can be used, but a
more accurate representation can be used :
mdi {
connector-0 {
media = "BaseT";
pairs = <2>;
};
};
From that information, we can derive the max speed reachable on the
port.
Another benefit of having that is to avoid vendor-specific DT properties
(micrel,fiber-mode or ti,fiber-mode).
This basic representation is meant to be expanded, by the introduction
of port ops, userspace listing of ports, and support for multi-port
devices.
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260108080041.553250-4-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can reduce the size of struct phy_device a little by switching
the type of members pause and asym_pause from int to a single bit.
As C99 is supported now, we can use type bool for the bitfield members,
what provides us with the benefit of the usual implicit bool conversions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/764e9a31-b40b-4dc9-b808-118192a16d87@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add an iterator for all PHY's on a MII bus, and phy_find_next()
as a prerequisite.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/cd112f15-401a-43d9-8525-9ff0965a68cd@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add phy_may_wakeup() which uses the driver model's device_may_wakeup()
when the PHY driver has marked the device as wakeup capable in the
driver model, otherwise use phy_drv_wol_enabled().
Replace the sites that used to call phy_drv_wol_enabled() with this
as checking the driver model will be more efficient than checking the
WoL state.
Export phy_may_wakeup() so that phylink can use it.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vBrQx-0000000BLzO-1RLt@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The blamed commit changed the conditions which phylib uses to stop
and start the state machine in the suspend and resume paths, and
while improving it, has caused two issues.
The original code used this test:
phydev->attached_dev && phydev->adjust_link
and if true, the paths would handle the PHY state machine. This test
evaluates true for normal drivers that are using phylib directly
while the PHY is attached to the network device, but false in all
other cases, which include the following cases:
- when the PHY has never been attached to a network device.
- when the PHY has been detached from a network device (as phy_detach()
sets phydev->attached_dev to NULL, phy_disconnect() calls
phy_detach() and additionally sets phydev->adjust_link NULL.)
- when phylink is using the driver (as phydev->adjust_link is NULL.)
Only the third case was incorrect, and the blamed commit attempted to
fix this by changing this test to (simplified for brevity, see
phy_uses_state_machine()):
phydev->phy_link_change == phy_link_change ?
phydev->attached_dev && phydev->adjust_link : true
However, this also incorrectly evaluates true in the first two cases.
Fix the first case by ensuring that phy_uses_state_machine() returns
false when phydev->phy_link_change is NULL.
Fix the second case by ensuring that phydev->phy_link_change is set to
NULL when phy_detach() is called.
Reported-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250806082931.3289134-1-xu.yang_2@nxp.com
Fixes: fc75ea20ff ("net: phy: allow MDIO bus PM ops to start/stop state machine for phylink-controlled PHY")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/E1uvMEz-00000003Aoe-3qWe@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a PHY has no driver, the genphy driver is probed/removed directly in
phy_attach/detach. If the PHY's ofnode has an "leds" subnode, then the
LEDs will be (un)registered when probing/removing the genphy driver.
This could occur if the leds are for a non-generic driver that isn't
loaded for whatever reason. Synchronously removing the PHY device in
phy_detach leads to the following deadlock:
rtnl_lock()
ndo_close()
...
phy_detach()
phy_remove()
phy_leds_unregister()
led_classdev_unregister()
led_trigger_set()
netdev_trigger_deactivate()
unregister_netdevice_notifier()
rtnl_lock()
There is a corresponding deadlock on the open/register side of things
(and that one is reported by lockdep), but it requires a race while this
one is deterministic. Regular drivers do not have this problem since
they are probed asynchronously (without RTNL held).
Generic PHYs do not support LEDs anyway, so don't bother registering
them.
[JakubL this is a net-next version of
commit f0f2b992d8 ("net: phy: Don't register LEDs for genphy"),
which uses APIs removed in -next.]
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20250710201454.1280277-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phy_id field only shows the PHY ID of the C22 device, and the C45
device did not store its PHY ID in this field.
Add a new phy_mmd_group, and export the mmd<n>_device_id for the C45
device. These files are invisible to the C22 device.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250613131903.2961-1-yajun.deng@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Remove now unused function phy_driver_is_genphy_10g().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/49b0589a-9604-4ee9-add5-28fbbbe2c2f3@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use new flag phydev->is_genphy_driven to simplify this function.
Note that this includes a minor functional change:
Now this function returns true if ANY of the genphy drivers
is bound to the PHY device.
We have only one user in DSA driver mt7530, and there the
functional change doesn't matter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/c9ac3a7d-262a-425d-9153-97fe3ca6280a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to get rid of phy_driver_is_genphy() and
phy_driver_is_genphy_10g(), as first step add and use a flag
phydev->is_genphy_driven.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/3f3ad6dc-402e-4915-8d5a-2306b6d5562b@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simplify the arguments passed to phy_get_internal_delay() - the "dev"
argument is always &phydev->mdio.dev, and as the phydev is passed in,
there's no need to also pass in the struct device, especially when this
function is the only reason for the caller to have a local "dev"
variable.
Remove the redundant "dev" argument, and update the callers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E1uPLwB-003VzR-4C@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
genphy_c45_read_status() is exported, so we can move definition of
genphy_c45_driver to phy_device.c and make it static. This helps
to clean up phy.h a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/ead3ab17-22d0-4cd3-901c-3d493ab851e6@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a potential crash issue when disabling and re-enabling the
network port. When disabling the network port, phy_detach() calls
device_link_del() to remove the device link, but it does not clear
phydev->devlink, so phydev->devlink is not a NULL pointer. Then the
network port is re-enabled, but if phy_attach_direct() fails before
calling device_link_add(), the code jumps to the "error" label and
calls phy_detach(). Since phydev->devlink retains the old value from
the previous attach/detach cycle, device_link_del() uses the old value,
which accesses a NULL pointer and causes a crash. The simplified crash
log is as follows.
[ 24.702421] Call trace:
[ 24.704856] device_link_put_kref+0x20/0x120
[ 24.709124] device_link_del+0x30/0x48
[ 24.712864] phy_detach+0x24/0x168
[ 24.716261] phy_attach_direct+0x168/0x3a4
[ 24.720352] phylink_fwnode_phy_connect+0xc8/0x14c
[ 24.725140] phylink_of_phy_connect+0x1c/0x34
Therefore, phydev->devlink needs to be cleared when the device link is
deleted.
Fixes: bc66fa87d4 ("net: phy: Add link between phy dev and mac dev")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250523083759.3741168-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce new API, genphy_match_phy_device(), to provide a way to check
to match a PHY driver for a PHY device based on the info stored in the
PHY device struct.
The function generalize the logic used in phy_bus_match() to check the
PHY ID whether if C45 or C22 ID should be used for matching.
This is useful for custom .match_phy_device function that wants to use
the generic logic under some condition. (example a PHY is already setup
and provide the correct PHY ID)
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-5-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass PHY driver pointer to .match_phy_device OP in addition to phydev.
Having access to the PHY driver struct might be useful to check the
PHY ID of the driver is being matched for in case the PHY ID scanned in
the phydev is not consistent.
A scenario for this is a PHY that change PHY ID after a firmware is
loaded, in such case, the PHY ID stored in PHY device struct is not
valid anymore and PHY will manually scan the ID in the match_phy_device
function.
Having the PHY driver info is also useful for those PHY driver that
implement multiple simple .match_phy_device OP to match specific MMD PHY
ID. With this extra info if the parsing logic is the same, the matching
function can be generalized by using the phy_id in the PHY driver
instead of hardcoding.
Rust wrapper callback is updated to align to the new match_phy_device
arguments.
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Benno Lossin <lossin@kernel.org> # for Rust
Reviewed-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-2-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After having factored out the provider part from mdio_bus.c, we can
make the mdio consumer / device layer a separate module. This also
allows to remove Kconfig symbol MDIO_DEVICE.
The module init / exit functions from mdio_bus.c no longer have to be
called from phy_device.c. The link order defined in
drivers/net/phy/Makefile ensures that init / exit functions are called
in the right order.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/dba6b156-5748-44ce-b5e2-e8dc2fcee5a7@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Refactor to check if the fwnode we got is correct and return if so,
otherwise do additional checks. Using same pattern in all conditionals
makes it slightly easier to read and understand.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250430143802.3714405-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add helper which returns the MAC termination resistance value. Modifying
the resistance to an appropriate value can reduce signal reflections and
therefore improve signal quality.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Link: https://patch.msgid.link/20250416-dp83822-mac-impedance-v3-3-028ac426cddb@liebherr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DSA has 2 kinds of drivers:
1. Those who call dsa_switch_suspend() and dsa_switch_resume() from
their device PM ops: qca8k-8xxx, bcm_sf2, microchip ksz
2. Those who don't: all others. The above methods should be optional.
For type 1, dsa_switch_suspend() calls dsa_user_suspend() -> phylink_stop(),
and dsa_switch_resume() calls dsa_user_resume() -> phylink_start().
These seem good candidates for setting mac_managed_pm = true because
that is essentially its definition [1], but that does not seem to be the
biggest problem for now, and is not what this change focuses on.
Talking strictly about the 2nd category of DSA drivers here (which
do not have MAC managed PM, meaning that for their attached PHYs,
mdio_bus_phy_suspend() and mdio_bus_phy_resume() should run in full),
I have noticed that the following warning from mdio_bus_phy_resume() is
triggered:
WARN_ON(phydev->state != PHY_HALTED && phydev->state != PHY_READY &&
phydev->state != PHY_UP);
because the PHY state machine is running.
It's running as a result of a previous dsa_user_open() -> ... ->
phylink_start() -> phy_start() having been initiated by the user.
The previous mdio_bus_phy_suspend() was supposed to have called
phy_stop_machine(), but it didn't. So this is why the PHY is in state
PHY_NOLINK by the time mdio_bus_phy_resume() runs.
mdio_bus_phy_suspend() did not call phy_stop_machine() because for
phylink, the phydev->adjust_link function pointer is NULL. This seems a
technicality introduced by commit fddd91016d ("phylib: fix PAL state
machine restart on resume"). That commit was written before phylink
existed, and was intended to avoid crashing with consumer drivers which
don't use the PHY state machine - phylink always does, when using a PHY.
But phylink itself has historically not been developed with
suspend/resume in mind, and apparently not tested too much in that
scenario, allowing this bug to exist unnoticed for so long. Plus, prior
to the WARN_ON(), it would have likely been invisible.
This issue is not in fact restricted to type 2 DSA drivers (according to
the above ad-hoc classification), but can be extrapolated to any MAC
driver with phylink and MDIO-bus-managed PHY PM ops. DSA is just where
the issue was reported. Assuming mac_managed_pm is set correctly, a
quick search indicates the following other drivers might be affected:
$ grep -Zlr PHYLINK_NETDEV drivers/ | xargs -0 grep -L mac_managed_pm
drivers/net/ethernet/atheros/ag71xx.c
drivers/net/ethernet/microchip/sparx5/sparx5_main.c
drivers/net/ethernet/microchip/lan966x/lan966x_main.c
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c
drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c
drivers/net/ethernet/freescale/ucc_geth.c
drivers/net/ethernet/freescale/enetc/enetc_pf_common.c
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
drivers/net/ethernet/marvell/mvneta.c
drivers/net/ethernet/marvell/prestera/prestera_main.c
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/altera/altera_tse_main.c
drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
drivers/net/ethernet/meta/fbnic/fbnic_phylink.c
drivers/net/ethernet/tehuti/tn40_phy.c
drivers/net/ethernet/mscc/ocelot_net.c
Make the existing conditions dependent on the PHY device having a
phydev->phy_link_change() implementation equal to the default
phy_link_change() provided by phylib. Otherwise, we implicitly know that
the phydev has the phylink-provided phylink_phy_change() callback, and
when phylink is used, the PHY state machine always needs to be stopped/
started on the suspend/resume path. The code is structured as such that
if phydev->phy_link_change() is absent, it is a matter of time until the
kernel will crash - no need to further complicate the test.
Thus, for the situation where the PM is not managed by the MAC, we will
make the MDIO bus PM ops treat identically the phylink-controlled PHYs
with the phylib-controlled PHYs where an adjust_link() callback is
supplied. In both cases, the MDIO bus PM ops should stop and restart the
PHY state machine.
[1] https://lore.kernel.org/netdev/Z-1tiW9zjcoFkhwc@shell.armlinux.org.uk/
Fixes: 744d23c71a ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Reported-by: Wei Fang <wei.fang@nxp.com>
Tested-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250407094042.2155633-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an upcoming change, mdio_bus_phy_may_suspend() will need to
distinguish a phylib-based PHY client from a phylink PHY client.
For that, it will need to compare the phydev->phy_link_change() function
pointer with the eponymous phy_link_change() provided by phylib.
To avoid forward function declarations, the default PHY link state
change method should be moved upwards. There is no functional change
associated with this patch, it is only to reduce the noise from a real
bug fix.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250407093900.2155112-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
phy_loopback() leaves it to the PHY driver to select the speed of the
loopback mode. Thus, the speed of the loopback mode depends on the PHY
driver in use.
Add support for speed selection to phy_loopback() to enable loopback
with defined speeds. Ensure that link up is signaled if speed changes
as speed is not allowed to change during link up. Link down and up is
necessary for a new speed.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://patch.msgid.link/20250312203010.47429-3-gerhard@engleder-embedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
PHY drivers support loopback mode, but it is not possible to select the
speed of the loopback mode. The speed is chosen by the set_loopback()
operation of the PHY driver. Same is valid for genphy_loopback().
There are PHYs that support loopback with different speeds. Extend
set_loopback() to make loopback speed selection possible.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250312203010.47429-2-gerhard@engleder-embedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When configuring PHY advertising with autoneg disabled, we lookd for an
exact linkmode to advertise and configure for the requested Speed and
Duplex, specially at or over 1G.
Using phy_caps_lookup allows us to build a list of the supported
linkmodes at that speed that we can advertise instead of the first mode
that matches.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-9-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The canonical definition for all the link modes is in linux/ethtool.h,
which is complemented by the link_mode_params array stored in
net/ethtool/common.h . That array contains all the metadata about each
of these modes, including the Speed and Duplex information.
Phylib and phylink needs that information as well for internal
management of the link, which was done by duplicating that information
in locally-stored arrays and lookup functions. This makes it easy for
developpers adding new modes to forget modifying phylib and phylink
accordingly.
However, the link_mode_params array in net/ethtool/common.c is fairly
inefficient to search through, as it isn't sorted in any manner. Phylib
and phylink perform a lot of lookup operations, mostly to filter modes
by speed and/or duplex.
We therefore introduce the link_caps private array in phy_caps.c, that
indexes linkmodes in a more efficient manner. Each element associated a
tuple <speed, duplex> to a bitfield of all the linkmodes runs at these
speed/duplex.
We end-up with an array that's fairly short, easily addressable and that
it optimised for the typical use-cases of phylib/phylink.
That array is initialized at the same time as phylib. As the
link_mode_params array is part of the net stack, which phylink depends
on, it should always be accessible from phylib.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-3-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch is the first step in moving the PHY package related code
to its own source file. No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/57df5c19-fbcd-45a7-9afd-cd4f74d7fa76@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A PHY driver may populate eee_disabled_modes in its probe or get_features
callback, therefore filter the EEE advertisement read from the PHY.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/493f3e2e-9cfc-445d-adbe-58d9c117a489@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
