Setting RBUF_EEE_EN | RBUF_PM_EN in RBUF_ENERGY_CTRL breaks the RX
path on GENET hardware once MAC EEE becomes active. RX traffic stops
flowing while the link stays up and the usual descriptor/RX error
counters remain quiet. In that state the MAC still accepts frames
(rbuf_ovflow_cnt keeps climbing) but RBUF no longer forwards them to
DMA, so rx_packets is no longer incremented at the netdev level. On
some boards the corruption ends up as a paging fault in
skb_release_data via bcmgenet_rx_poll on an LPI exit.
Reproduced on Pi 4B (BCM2711 + BCM54213PE) and confirmed by Florian
Fainelli on an internal Broadcom 4908-family board with the same crash
signature. RBUF_PM_EN is not publicly documented.
This shows up more often now that phy_support_eee() enables EEE by
default, but it also affects older kernels as soon as TX LPI is
turned on via ethtool, so it is not specific to recent changes.
Always clear RBUF_EEE_EN | RBUF_PM_EN in bcmgenet_eee_enable_set so
the bits stay off across resets. UMAC and TBUF setup is left alone so
TX-side EEE keeps working.
Link: https://github.com/raspberrypi/linux/issues/7304
Fixes: 6ef398ea60 ("net: bcmgenet: add EEE support")
Cc: stable@vger.kernel.org
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260520184320.652053-1-nb@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The bcmgenet_timeout handler tries to take down all tx queues when
a single queue times out. This is over zealous and causes many race
conditions with queues that are still chugging along. Instead lets
only restart the timed out queue.
Fixes: 13ea657806 ("net: bcmgenet: improve TX timeout")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Tested-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260406175756.134567-4-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While reclaiming the tx queue we fast forward the write pointer to
drop any data in flight. These dropped frames are not added back
to the pool of free bds. We also need to tell the netdev that we
are dropping said data.
Fixes: f1bacae8b6 ("net: bcmgenet: support reclaiming unsent Tx packets")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Tested-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260406175756.134567-3-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The write_ptr points to the next open tx_cb. We want to return the
tx_cb that gets rewinded, so we must rewind the pointer first then
return the tx_cb that it points to. That way the txcb can be correctly
cleaned up.
Fixes: 876dbadd53 ("net: bcmgenet: Fix unmapping of fragments in bcmgenet_xmit()")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260406175756.134567-2-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some systems require more than 5ms to get into WoL mode. Increase the
timeout value to 50ms.
Fixes: c51de7f397 ("net: bcmgenet: add Wake-on-LAN support code")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260312191852.3904571-1-justin.chen@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The bcmgenet EEE implementation is broken in several ways.
phy_support_eee() is never called, so the PHY never advertises EEE
and phylib never sets phydev->enable_tx_lpi. bcmgenet_mac_config()
checks priv->eee.eee_enabled to decide whether to enable the MAC
LPI logic, but that field is never initialised to true, so the MAC
never enters Low Power Idle even when EEE is negotiated - wasting
the power savings EEE is designed to provide. The only way to get
EEE working at all is a manual 'ethtool --set-eee eth0 eee on' after
every link-up, and even then bcmgenet_get_eee() immediately clobbers
the reported state because phy_ethtool_get_eee() overwrites
eee_enabled and tx_lpi_enabled with the uninitialised PHY eee_cfg
values. Finally, bcmgenet_mac_config() is only called on link-up,
so EEE is never disabled in hardware on link-down.
Fix all of this by removing the MAC-side EEE state tracking
(priv->eee) and aligning with the pattern used by other non-phylink
MAC drivers such as FEC.
Call phy_support_eee() in bcmgenet_mii_probe() so the PHY advertises
EEE link modes and phylib tracks negotiation state. Move the EEE
hardware control to bcmgenet_mii_setup(), which is called on every
link event, and drive it directly from phydev->enable_tx_lpi - the
flag phylib sets when EEE is negotiated and the user has not disabled
it. This enables EEE automatically once the link partner agrees and
disables it cleanly on link-down.
Make bcmgenet_get_eee() and bcmgenet_set_eee() pure passthroughs to
phy_ethtool_get_eee() and phy_ethtool_set_eee(), with the MAC
hardware register read/written for tx_lpi_timer. Drop struct
ethtool_keee eee from struct bcmgenet_priv.
Fixes: fe0d4fd928 ("net: phy: Keep track of EEE configuration")
Link: https://lore.kernel.org/netdev/d352039f-4cbb-41e6-9aeb-0b4f3941b54c@lunn.ch/
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260310054935.1238594-1-nb@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This converts some of the visually simpler cases that have been split
over multiple lines. I only did the ones that are easy to verify the
resulting diff by having just that final GFP_KERNEL argument on the next
line.
Somebody should probably do a proper coccinelle script for this, but for
me the trivial script actually resulted in an assertion failure in the
middle of the script. I probably had made it a bit _too_ trivial.
So after fighting that far a while I decided to just do some of the
syntactically simpler cases with variations of the previous 'sed'
scripts.
The more syntactically complex multi-line cases would mostly really want
whitespace cleanup anyway.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
Commit 84eaf4359c ("net: ethtool: add get_rx_ring_count callback to
optimize RX ring queries") added specific support for GRXRINGS callback,
simplifying .get_rxnfc.
Remove the handling of GRXRINGS in .get_rxnfc() by moving it to the new
.get_rx_ring_count().
This simplifies the RX ring count retrieval and aligns bcmgenet with the
new ethtool API for querying RX ring parameters.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20251127-grxrings_broadcom-v1-2-b0b182864950@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This effectively reverts b0ba512e25 ("net: bcmgenet: enable driver to
work without a device tree"). There has never been an in-tree user of
struct bcmgenet_platform_data, all devices use OF or ACPI.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/108b4e64-55d4-4b4e-9a11-3c810c319d66@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The disable sequence in bcmgenet_phy_power_set() is updated to
match the inverse sequence and timing (and spacing) of the
enable sequence. This ensures that LEDs driven by the GENET IP
are disabled when the GPHY is powered down.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250614025817.3808354-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make use of the return value from napi_complete_done(). This allows users to
use the gro_flush_timeout and napi_defer_hard_irqs sysfs attributes for
configuring software interrupt coalescing.
Signed-off-by: Zak Kemble <zakkemble@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250610220403.935-2-zakkemble@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hardware discarded packets are now counted in their own missed stat
instead of being lumped in with general errors.
Signed-off-by: Zak Kemble <zakkemble@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250519113257.1031-3-zakkemble@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the driver to use ndo_get_stats64, rtnl_link_stats64 and
u64_stats_t counters for statistics.
Signed-off-by: Zak Kemble <zakkemble@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250519113257.1031-2-zakkemble@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All callers pass PHY_POLL, therefore remove irq argument from
fixed_phy_register().
Note: I keep the irq argument in fixed_phy_add_gpiod() for now,
for the case that somebody may want to use a GPIO interrupt in
the future, by e.g. adding a call to fwnode_irq_get() to
fixed_phy_get_gpiod().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/31cdb232-a5e9-4997-a285-cb9a7d208124@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the network interface is configured for Wake-on-LAN we should
avoid bringing the interface down and up since it slows the time
to reestablish network traffic on resume.
Redundant calls to phy_suspend() and phy_resume() are removed
since they are already invoked from within phy_stop() and
phy_start() called from bcmgenet_netif_stop() and
bcmgenet_netif_start().
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250306192643.2383632-15-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It is possible for a WoL power up to fail due to the GENET being
reset while in the suspend state. Allow these failures to be
returned as error codes to allow different recovery behavior
when necessary.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250306192643.2383632-14-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The bcmgenet_power_up() function is moved from the resume method
to the resume_noirq method for symmetry with the suspend_noirq
method. This allows the wol_active flag to be removed.
The UMAC_IRQ_WAKE_EVENT interrupts that can be unmasked by the
bcmgenet_wol_power_down_cfg() function are now re-masked by the
bcmgenet_wol_power_up_cfg() function at the resume_noirq level
as well.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250306192643.2383632-13-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When disabling the transmitter any outstanding packets can now
be reclaimed by bcmgenet_tx_reclaim_all() rather than by the
bcmgenet_fini_dma() function.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250306192643.2383632-12-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The bcmgenet_rdma_disable and bcmgenet_tdma_disable functions
are introduced to provide a common method for disabling each
dma and the code is simplified.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250306192643.2383632-11-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The functions bcmgenet_dma_disable and bcmgenet_enable_dma are
only used as part of dma initialization. Their functionality is
moved inside bcmgenet_init_dma and the functions are removed.
Since the dma is always disabled inside of bcmgenet_init_dma,
the initialization functions bcmgenet_init_rx_queues and
bcmgenet_init_tx_queues no longer need to attempt to manage its
state.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250306192643.2383632-10-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the individual queues manage their own DMA enables there
is no need to return dma_ctrl from bcmgenet_dma_disable() and
pass it back to bcmgenet_enable_dma().
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250306192643.2383632-9-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that the DESC_INDEX ring descriptor is no longer used we can
enable hardware discarding of flows by routing them to a queue
that is not enabled.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250306192643.2383632-8-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The default transmit and receive packet handling is moved from
the DESC_INDEX (i.e. 16) descriptor rings to the Ring 0 queues.
This saves a fair amount of special case code by unifying the
handling.
A default dummy filter is enabled in the Hardware Filter Block
to route default receive packets to Ring 0.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250306192643.2383632-7-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend the bcmgenet_hfb_* API to allow initialization and
programming of the Hardware Filter Block on GENET v1 and
GENET v2 hardware. Programming of ethtool flows is still
not supported on this older hardware.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250306192643.2383632-6-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The major revision of the GENET core in the BCM7712 SoC was bumped
to 7 but it is compatible with the GENETv5 implementation. This
commit maps the version accordingly to avoid a warning.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250306192643.2383632-5-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The feature flags are moved and consolidated to the primary
private driver structure and are now initialized from the
platform device data rather than the hardware parameters to
allow finer control over which platforms use which features.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250306192643.2383632-4-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce helper functions to indicate whether the driver should
make use of a particular feature that it supports. These helpers
abstract the implementation of how the feature availability is
encoded.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250306192643.2383632-3-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The entries of the bcmgenet_hw_params array are broken out to
remove unused and duplicate entries and are made read only since
they should not change for a specific version of the GENET
hardware.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250306192643.2383632-2-opendmb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some Wake-on-LAN modes such as WAKE_FILTER may only be supported by the MAC,
while others might be only supported by the PHY. Make sure that the .get_wol()
returns the union of both rather than only that of the PHY if the PHY supports
Wake-on-LAN.
When disabling Wake-on-LAN, make sure that this is done at both the PHY
and MAC level, rather than doing an early return from the PHY driver.
Fixes: 7e400ff35c ("net: bcmgenet: Add support for PHY-based Wake-on-LAN")
Fixes: 9ee09edc05 ("net: bcmgenet: Properly overlay PHY and MAC Wake-on-LAN capabilities")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250129231342.35013-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The latter is the preferred way to copy ethtool strings.
Avoids manually incrementing the pointer. Cleans up the code quite well.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20241104205317.306140-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net_dim() is currently passed a struct dim_sample argument by value.
struct dim_sample is 24 bytes. Since this is greater 16 bytes, x86-64
passes it on the stack. All callers have already initialized dim_sample
on the stack, so passing it by value requires pushing a duplicated copy
to the stack. Either witing to the stack and immediately reading it, or
perhaps dereferencing addresses relative to the stack pointer in a chain
of push instructions, seems to perform quite poorly.
In a heavy TCP workload, mlx5e_handle_rx_dim() consumes 3% of CPU time,
94% of which is attributed to the first push instruction to copy
dim_sample on the stack for the call to net_dim():
// Call ktime_get()
0.26 |4ead2: call 4ead7 <mlx5e_handle_rx_dim+0x47>
// Pass the address of struct dim in %rdi
|4ead7: lea 0x3d0(%rbx),%rdi
// Set dim_sample.pkt_ctr
|4eade: mov %r13d,0x8(%rsp)
// Set dim_sample.byte_ctr
|4eae3: mov %r12d,0xc(%rsp)
// Set dim_sample.event_ctr
0.15 |4eae8: mov %bp,0x10(%rsp)
// Duplicate dim_sample on the stack
94.16 |4eaed: push 0x10(%rsp)
2.79 |4eaf1: push 0x10(%rsp)
0.07 |4eaf5: push %rax
// Call net_dim()
0.21 |4eaf6: call 4eafb <mlx5e_handle_rx_dim+0x6b>
To allow the caller to reuse the struct dim_sample already on the stack,
pass the struct dim_sample by reference to net_dim().
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Arthur Kiyanovski <akiyano@amazon.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Link: https://patch.msgid.link/20241031002326.3426181-2-csander@purestorage.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net/ethernet to use
.remove(), with the eventual goal to drop struct
platform_driver::remove_new(). As .remove() and .remove_new() have the
same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/18f7c585a1a8a8ac8b03a2fca7de19bd5c52ac2b.1727949050.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Some Wake-on-LAN modes such as WAKE_FILTER may only be supported by the MAC,
while others might be only supported by the PHY. Make sure that the .get_wol()
returns the union of both rather than only that of the PHY if the PHY supports
Wake-on-LAN.
Fixes: 7e400ff35c ("net: bcmgenet: Add support for PHY-based Wake-on-LAN")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240806175659.3232204-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The UMAC_CMD register is written from different execution
contexts and has insufficient synchronization protections to
prevent possible corruption. Of particular concern are the
acceses from the phy_device delayed work context used by the
adjust_link call and the BH context that may be used by the
ndo_set_rx_mode call.
A spinlock is added to the driver to protect contended register
accesses (i.e. reg_lock) and it is used to synchronize accesses
to UMAC_CMD.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_set_rx_mode function is synchronized with the
netif_addr_lock spinlock and BHs disabled. Since this
function is also invoked directly from the driver the
same synchronization should be applied.
Fixes: 72f9634762 ("net: bcmgenet: set Rx mode before starting netif")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EXT_RGMII_OOB_CTRL register can be written from different
contexts. It is predominantly written from the adjust_link
handler which is synchronized by the phydev->lock, but can
also be written from a different context when configuring the
mii in bcmgenet_mii_config().
The chances of contention are quite low, but it is conceivable
that adjust_link could occur during resume when WoL is enabled
so use the phydev->lock synchronizer in bcmgenet_mii_config()
to be sure.
Fixes: afe3f907d2 ("net: bcmgenet: power on MII block for all MII modes")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the RBUF logic is not reset when the kernel starts then there
may be some data left over from any network boot loader. If the
64-byte packet headers are enabled then this can be fatal.
Extend bcmgenet_dma_disable to do perform the reset, but not when
called from bcmgenet_resume in order to preserve a wake packet.
N.B. This different handling of resume is just based on a hunch -
why else wouldn't one reset the RBUF as well as the TBUF? If this
isn't the case then it's easy to change the patch to make the RBUF
reset unconditional.
See: https://github.com/raspberrypi/linux/issues/3850
See: https://github.com/raspberrypi/firmware/issues/1882
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Maarten Vanraes <maarten@rmail.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1b5ea7ffb7 ("net:
bcmgenet: Ensure MDIO unregistration has clocks enabled"). This is no
longer necessary now that the MDIO bus controller has a clock that it
can manage around the I/O accesses.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GENET has historically had to create a MDIO platform device for its
controller and pass some auxiliary data to it, like a MDIO completion
callback. Now we also pass the "main" clock to allow for the MDIO bus
controller to manage that clock adequately around I/O accesses.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_get_eee() sets edata->eee_active and edata->eee_enabled from
its own copy, and then calls phy_ethtool_get_eee() which in turn will
call genphy_c45_ethtool_get_eee().
genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active
with its own interpretation from the PHYs settings and negotiation
result.
Therefore, setting these members in bcmgenet_get_eee() is redundant,
and can be removed. This also makes priv->eee.eee_active unnecessary,
so remove this and use a local variable where appropriate.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1rWbN7-002cCn-RO@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag DMA_TX_APPEND_CRC was only written to the first DMA descriptor
in the TX path, where each descriptor corresponds to a single skbuff
fragment (or the skbuff head). This led to packets with no FCS appearing
on the wire if the kernel allocated the packet in fragments, which would
always happen when using PACKET_MMAP/TPACKET (cf. tpacket_fill_skb() in
net/af_packet.c).
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Adrian Cinal <adriancinal1@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231228135638.1339245-1-adriancinal1@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver gained a .ndo_poll_controller() at a time where the TX
cleaning process was always done from NAPI which makes this unnecessary.
See commit ac3d9dd034 ("netpoll: make ndo_poll_controller() optional")
for more background.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert these drivers from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
