Add chip info structs and device table entries for ADRF5702 and ADRF5703
Digital Step Attenuators.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for the following digital step attenuators:
- HMC271A: 1dB LSB 5-Bit Digital Attenuator SMT, 0.7 - 3.7 GHz
- ADRF5720: 0.5 dB LSB, 6-Bit, Digital Attenuator, 9 kHz to 40 GHz
- ADRF5730: 0.5 dB LSB, 6-Bit, Digital Attenuator, 100 MHz to 40 GHz
- ADRF5731: 2 dB LSB, 4-Bit, Digital Attenuator, 100 MHz to 40 GHz
- HMC1018A: 1.0 dB LSB GaAs MMIC 5-BIT DIGITAL ATTENUATOR, 0.1 - 30 GHz
- HMC1019A: 0.5 dB LSB GaAs MMIC 5-BIT DIGITAL ATTENUATOR, 0.1 - 30 GHz
Additionally, copyright notice was updated with current year.
Co-developed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Co-developed-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some parts may consume enable GPIO to enable serial mode
(HMC1119's and HMC792A P/S pin) or powerup the device
(e.g. ADA4961's PWUP pin).
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop the enum ID, split chip info table into per-device structs and add
of_match_table. Additionally, add 'name' field into the chip info struct,
dropping the usage of spi_get_device_id().
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop switch case on the enum ID in favor of extended chip info table,
containing:
- gain_step, indicating with sign the start of the code range;
- num_channels, to indicate the number IIO channels;
- pack_code() function to describe how SPI buffer is populated;
Which allowed for a simplified read_raw() and write_raw() callbacks. The
probe() function was adjusted accordingly. The linux/array_size.h include
is removed as number of channels is provided by chip info table.
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove reset_gpio from the device state struct and use the reset_control
interface instead, using a local variable, as it is not being used
anywhere else. The reset controller init is moved out from the switch case
and optionally initialized for every device variant. Although not all
devices have a reset pin the code does not need to change if it is not
wired.
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Adhere modern device resource management with the following:
- Voltage regulator managed and enabled internally;
- IIO device registration handled with devm_iio_device_register();
- removal of goto's from the probe function;
- ad8366_remove() removed as it is not needed anymore;
With the drop of goto's dev_err_probe() is used to report probe errors.
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Adopt proper mutex lifecycle with devm_mutex_init(), replacing
mutex_init(). Mutex init is moved up (before regulator init),
so that goto statement in the error path is avoided (which will
be cleaned up later).
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Create local device pointer in the probe function to shorten lines, making
the code easier to read. The local device pointer replaces &spi->dev and
will be reused across other probe function places in later patches.
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Apply IWYU principle, removing the following headers:
- linux/device.h: no usage of devm_add_action_or_reset, device_attr...
- linux/kernel.h: no usage of container_of, kasprintf, ...
- linux/slab.h: memory management handled by iio
- linux/sysfs.h: sysfs interaction is managed by iio
- linux/iio/sysfs.h: not using iio device attributes in this driver
Adding the following missing headers:
+ linux/array_size.h: for ARRAY_SIZE
+ linux/bits.h: for BIT
+ linux/dev_printk.h: for dev_err
+ linux/math.h: for abs
+ linux/mutex.h: for mutex_lock, mutex_unlock
+ linux/mod_devicetable.h: for spi_device_id
+ linux/types.h for NULL, __aligned
Additionally, those include directives are alphabetically sorted.
Signed-off-by: Rodrigo Alencar <rodrigo.alencar@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use `\t(\{ ?\},|\{\}|\{\s*/\*.*\*/\s*\},?)$` regex to find and replace
the array sentinel in all IIO drivers to the same style.
For some time, we've been trying to consistently use `{ }` (no trailing
comma, no comment, one space between braces) for array sentinels in the
IIO subsystem. Still nearly 50% of existing code uses a different style.
To save reviewers from having to request this trivial change as
frequently, let's normalize the style in all existing IIO drivers.
At least when code is copy/pasted to new drivers, the style will be
consistent.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250411-iio-sentinel-normalization-v1-1-d293de3e3d93@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This removes the following checkpatch issue:
- ERROR: space prohibited before that ',' (ctx:WxW)
Signed-off-by: Franziska Naepelt <franziska.naepelt@gmail.com>
Link: https://lore.kernel.org/r/20230528104802.22011-1-franziska.naepelt@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Update the comment to include 'may'.
Fixes: e71d42e03c ("iio: amplifiers: New driver for AD8366 Dual-Digital Variable Gain Amplifier")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-42-jic23@kernel.org
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
These were found by doing some shell magic:
------------
for file in $(git grep -w devm_iio_device_alloc | cut -d: -f1 | sort | uniq) ; do
if grep 'parent =' $file | grep -v trig | grep -vq devm_; then
echo "$file -> $(grep "parent =" $file)"
fi
done
-----------
The output is bearable [after the semantic patch is applied].
There is a mix of trigger assignments with some iio device parent
assignments that are removed via this patch.
JC: A few more added via inspection of all parent =
statements in drivers/iio. Some of these may just have crossed with this
series, others were less obvious to scripting due to some cross
file / module boundary calls.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since if there is no GPIO, nothing happens, replace devm_gpiod_get()
with devm_gpiod_get_optional().
Also add IS_ERR() to fix the missing-check warning.
Fixes: cee211f4e5 ("iio: amplifiers: ad8366: Add support for the ADA4961 DGA")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change adds support for the HMC1119 Silicon Digial Attenuator. The
HMC1119 is a broadband, highly accurate, 7-bit digital attenuator,
operating from 0.1 GHz to 6.0 GHz with 31.5 dB attenuation control range
in 0.25 dB steps.
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/hmc1119.pdf
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch add write_raw_get_fmt function to specify conversion for
hardware gain.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADL5240 is a high performance, digitally controlled variable gain
amplifier (VGA) operating from 100 MHz to 4000 MHz. The VGA integrates a
high performance, 20 dB gain, internally matched amplifier (AMP) with a
6-bit digital step attenuator (DSA) that has a gain control range of
31.5 dB in 0.5 dB steps with ±0.25 dB step accuracy.
Datasheet link:
https://www.analog.com/media/en/technical-documentation/data-sheets/adl5240.pdf
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change adds support for the ADA4961 BiCMOS RF Digital Gain Amplifier,
(DGA), which is optimized for driving heavy loads out 2.0 GHz and beyond.
The device typically achieves -90 dBc IMD3 performance at 500 MHz and
-85 dBc at 1.5 GHz.
Datasheet link:
http://www.analog.com/media/en/technical-documentation/data-sheets/ADA4961.pdf
This change re-uses the existing ad8366 driver, as most logic is similar.
Also, this chip has a reset pin which is initialized during probe.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SPI gain amplifiers are simple devices, with 1 or 2 channels, to which
are read-from/written-to.
The gain computation in ad8366_write_raw() has been updated to compute gain
in dB for negative values.
This driver will be extended to support other chips as well.
To do that, this rework handles the AD8366 device as a special-case (via
switch-statements). This will make things easier when adding new chips.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver is still using iio_dev's mlock to guard against inconsistent
state. This has been discouraged for some time.
This change switches to using it's own mutex, defined on the state struct.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the new `SPDX-License-Identifier` tag to specify the license.
For ad8366, also update copyright years in the header part.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Otherwise a race condition can occur, where userspace can start operations
before the channels have been properly initialized.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI core always reports the MODALIAS uevent as "spi:<modalias>"
regardless of the mechanism that was used to register the device
(i.e: OF or board code) and the table that is used later to match
the driver with the device (i.e: SPI id table or OF match table).
So drivers needs to export the SPI id table and this be built into
the module or udev won't have the necessary information to autoload
the needed driver module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fixes the following checkpatch.pl warning:
WARNING: type 'char unsigned' should be specified in [[un]signed]
[short|int|long|long long] order
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fixes the following checkpatch.pl error:
ERROR: space prohibited before that ',' (ctx:WxW)
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since devm_regulator_get is used, regulator_put should not be
used. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
devm_* APIs are device managed and make code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Michael Hennerich <hennerich@blackfin.uclinux.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, and __devexit
from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes since V1:
Apply review feedback:
Introduce and use IIO_CHAN_INFO_HARDWAREGAIN
Introduce and use Use IIO_VAL_INT_PLUS_MICRO_DB
Modify out of staging include paths.
Convert to new iio core API naming.
Changes since V2:
more sanity checking in write_raw
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
