NXP i.MX93 mediamix blk-ctrl contains one DISPLAY_MUX register which
configures parallel display format by using the "PARALLEL_DISP_FORMAT"
field. Add a DRM bridge driver to support the display format configuration.
[m.felsch@pengutronix.de: port to v7.0-rc1]
[m.felsch@pengutronix.de: add review feedback (Alexander)]
[m.felsch@pengutronix.de: fix to short Kconfig description (checkpath)]
[m.felsch@pengutronix.de: use "GPL" instead of "GPL v2" (checkpatch)]
[m.felsch@pengutronix.de: add bus-width support]
[ Liu Ying: Port to drm-misc/drm-misc-next(v7.2-rc2 based) ]
[ Liu Ying: Add nxp,imx91-pdfc compatible string ]
[ Liu Ying: Call drm_bridge_get() for next_bridge ]
[ Liu Ying: Reject unsupported output bus fmt in .atomic_get_input_bus_fmts() ]
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Link: https://patch.msgid.link/20260723-v6-18-topic-imx93-parallel-display-v13-1-ccf3f9bbc0fc@nxp.com
Signed-off-by: Liu Ying <victor.liu@nxp.com>
The imx8mp-hdmi-tx is one of many drivers based on dw-hdmi. dw-hdmi in turn
can operate in two different modes, depending on the platform data as set
by the driver:
A. hdmi->plat_data->output_port = 0:
the HDMI output (port@1) in device tree is not used [0]
B. hdmi->plat_data->output_port = 1:
the HDMI output (port@1) is parsed to find the next bridge
The imx8mp-hdmi-tx driver falls in case A. This implies next_bridge will
always be NULL, and so dw_hdmi_bridge_attach() [1] will always fail if
called with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.
In fact case A assumes that DRM_BRIDGE_ATTACH_NO_CONNECTOR is not set and
in that case it adds an HDMI Type A connector programmatically at bridge
attach time.
Support for DRM_BRIDGE_ATTACH_NO_CONNECTOR is implemented by dw-hdmi.c in
case B. However switching to base B requires that port@1 is connected to a
"next bridge" DT node, typically the HDMI connector, because dw-hdmi won't
add the connector when using DRM_BRIDGE_ATTACH_NO_CONNECTOR.
Many dts files for imx8mp-based boards in the kernel have such a connector
described and linked to port@1, so the pipeline will be fully attached up
to a display-connector and a drm_connector added by the
bridge-connector. Sadly some of those dts files don't have the connector
described. Adding it would solve the problem easily, but this would break
existing devices which do not update the dtb when upgrading to a newer
kernel.
In preparation for switching to case B while preserving backward
compatibility for such devices, introduce a module adding the
hdmi-connector node to the live device tree at init time. This will allow
the dw-hdmi code to find the next bridge (the one wrapping the
hdmi-connector) and let the pipeline work as before.
The module is inserted only if there is no endpoint in port@1. So boards
whose device tree describe the connector will not have the device tre
modified, and will start isntantiating the correct HDMI connector type as
described in the device tree.
For boards lacking a connector description in DT the overlay will be added,
abd the HDMI connector will be Type A, which is a reasonable fallback and
is what the driver is currently doing.
[0] https://elixir.bootlin.com/linux/v7.0-rc1/source/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c#L3310
[1] https://elixir.bootlin.com/linux/v7.0-rc1/source/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c#L2907
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Link: https://patch.msgid.link/20260407-drm-lcdif-dbanc-v4-8-247a16e61ef9@bootlin.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
As suggested by Dmitry, the DRM legacy bridge driver can be pulled
out of imx/ subdir for multi-platform use. The driver is also renamed
to make it more generic and suitable for platforms other than i.MX.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> # rk3588
Link: https://patch.msgid.link/20260409065301.446670-3-damon.ding@rock-chips.com
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
The HDMI TX Parallel Audio Interface (HTX_PAI) is a digital module that
acts as the bridge between the Audio Subsystem to the HDMI TX Controller.
This IP block is found in the HDMI subsystem of the i.MX8MP SoC.
Data received from the audio subsystem can have an arbitrary component
ordering. The HTX_PAI block has integrated muxing options to select which
sections of the 32-bit input data word will be mapped to each IEC60958
field. The HTX_PAI_FIELD_CTRL register contains mux selects to
individually select P,C,U,V,Data, and Preamble.
Use component helper so that imx8mp-hdmi-tx will be aggregate driver,
imx8mp-hdmi-pai will be component driver, then imx8mp-hdmi-pai can use
bind() ops to get the plat_data from imx8mp-hdmi-tx device.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20250923053001.2678596-6-shengjiu.wang@nxp.com
i.MX DRM DT bindings allow using either a proper panel / bridge graph to
provide information about connected panels, or just a display-timings DT
node, describing just the timings and the flags. Add helper bridge
driver supporting the latter usecase. It will be used by both LDB and
parallel-display drivers.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Chris Healy <cphealy@gmail.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de> # on imx6q-nitrogen6x
Link: https://patchwork.freedesktop.org/patch/msgid/20240602-drm-imx-cleanup-v3-9-e549e2a43100@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
This reverts commit c0e0f13935, as helper
code should always be selected by the driver that needs it, for the
convenience of the final user configuring a kernel.
The user who configures a kernel should not need to know which helpers
are needed for the driver he is interested in. Making a driver depend
on helper code means that the user needs to know which helpers to enable
first, which is very user-unfriendly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/bd93d43b07f8ed6368119f4a5ddac2ee80debe53.1713780345.git.geert+renesas@glider.be
Signed-off-by: Maxime Ripard <mripard@kernel.org>
When enabling i.MX8MP DWC HDMI driver, it automatically selects
PHY_FSL_SAMSUNG_HDMI_PHY, since it wont' work without the phy.
This may cause some Kconfig warnings during various build tests.
Fix this by implying the phy instead of selecting the phy.
To prevent this from happening with the DRM_IMX8MP_HDMI_PVI, also
imply it instead of selecting it.
Fixes: 1f36d63467 ("drm/bridge: imx: add bridge wrapper driver for i.MX8MP DWC HDMI")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404190103.lLm8LtuP-lkp@intel.com/
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240422103352.8886-1-aford173@gmail.com
DRM_DW_HDMI has a number of dependencies that might not be enabled.
However, drivers were used to selecting it while not enforcing the
DRM_DW_HDMI dependencies.
This could result in Kconfig warnings (and further build breakages) such
as:
Kconfig warnings: (for reference only)
WARNING: unmet direct dependencies detected for DRM_DW_HDMI
Depends on [n]: HAS_IOMEM [=y] && DRM [=m] && DRM_BRIDGE [=y] && DRM_DISPLAY_HELPER [=n]
Selected by [m]:
- DRM_SUN8I_DW_HDMI [=m] && HAS_IOMEM [=y] && DRM_SUN4I [=m]
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202403262127.kZkttfNz-lkp@intel.com/
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20240327-kms-kconfig-helpers-v3-7-eafee11b84b3@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Add a simple wrapper driver for the DWC HDMI bridge driver that
implements the few bits that are necessary to abstract the i.MX8MP
SoC integration.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20240203165307.7806-11-aford173@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240203165307.7806-11-aford173@gmail.com
This IP block is found in the HDMI subsystem of the i.MX8MP SoC. It has a
full timing generator and can switch between different video sources. On
the i.MX8MP however the only supported source is the LCDIF. The block
just needs to be powered up and told about the polarity of the video
sync signals to act in bypass mode.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20240203165307.7806-9-aford173@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240203165307.7806-9-aford173@gmail.com
Freescale i.MX93 SoC embeds a Synopsys Designware MIPI DSI host
controller and a Synopsys Designware MIPI DPHY. Some configurations
and extensions to them are controlled by i.MX93 media blk-ctrl.
Add a DRM bridge for i.MX93 MIPI DSI by using existing DW MIPI DSI
bridge helpers and implementing i.MX93 MIPI DSI specific extensions.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821034008.3876938-10-victor.liu@nxp.com
With CONFIG_DRM_IMX8QM_LDB=m and CONFIG_DRM_IMX8QXP_LDB=y (or vice
versa), imx-ldb-helper.o is linked to a module and also to vmlinux
even though the expected CFLAGS are different between builtins and
modules.
This is the same situation as fixed by commit 637a642f5c ("zstd:
Fixing mixed module-builtin objects").
Split imx-ldb-helper.c into a separate module.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230605120021.1774711-1-masahiroy@kernel.org
The various Freescale i.MX8 display bridges are only present on
Freescale i.MX8 SoCs. Hence add a dependency on ARCH_MXC, to prevent
asking the user about these drivers when configuring a kernel without
i.MX SoC support.
Fixes: e60c435484 ("drm/bridge: imx: Add LDB support for i.MX8qm")
Fixes: 3818715f62 ("drm/bridge: imx: Add LDB support for i.MX8qxp")
Fixes: 96988a526c ("drm/bridge: imx: Add i.MX8qxp pixel link to DPI support")
Fixes: 1ec17c26bc ("drm/bridge: imx: Add i.MX8qm/qxp display pixel link support")
Fixes: 93e163a9e0 ("drm/bridge: imx: Add i.MX8qm/qxp pixel combiner support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/42c542b53a1c8027b23a045045fbb7b34479913d.1656072500.git.geert+renesas@glider.be
This patch adds a drm bridge driver for i.MX8qm LVDS display bridge(LDB)
which is officially named as pixel mapper. The LDB has two channels.
Each of them supports up to 30bpp parallel input color format and can
map the input to VESA or JEIDA standards. The two channels can be used
simultaneously, either in dual mode or split mode. In dual mode, the
two channels output identical data. In split mode, channel0 outputs
odd pixels and channel1 outputs even pixels. This patch supports the
LDB single mode and split mode.
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Colibri iMX8X, LT170410-2WHC, LP156WF1
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220611141421.718743-13-victor.liu@nxp.com
This patch adds a drm bridge driver for i.MX8qxp LVDS display bridge(LDB)
which is officially named as pixel mapper. The LDB has two channels.
Each of them supports up to 24bpp parallel input color format and can map
the input to VESA or JEIDA standards. The two channels cannot be used
simultaneously, that is to say, the user should pick one of them to use.
Two LDB channels from two LDB instances can work together in LDB split
mode to support a dual link LVDS display. The channel indexes have to be
different. Channel0 outputs odd pixels and channel1 outputs even pixels.
This patch supports the LDB single mode and split mode.
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Colibri iMX8X, LT170410-2WHC, LP156WF1
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220611141421.718743-12-victor.liu@nxp.com
This patch adds a drm bridge driver for i.MX8qxp pixel link to display
pixel interface(PXL2DPI). The PXL2DPI interfaces the pixel link 36-bit
data output and the DSI controller’s MIPI-DPI 24-bit data input, and
inputs of LVDS Display Bridge(LDB) module used in LVDS mode, to remap
the pixel color codings between those modules. The PXL2DPI is purely
combinatorial.
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Colibri iMX8X, LT170410-2WHC, LP156WF1
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220611141421.718743-9-victor.liu@nxp.com
This patch adds a drm bridge driver for i.MX8qm/qxp display pixel link.
The pixel link forms a standard asynchronous linkage between
pixel sources(display controller or camera module) and pixel
consumers(imaging or displays). It consists of two distinct
functions, a pixel transfer function and a control interface.
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Colibri iMX8X, LT170410-2WHC, LP156WF1
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220611141421.718743-7-victor.liu@nxp.com
This patch adds a drm bridge driver for i.MX8qm/qxp pixel combiner.
The pixel combiner takes two output streams from a single display
controller and manipulates the two streams to support a number
of modes(bypass, pixel combine, YUV444 to YUV422, split_RGB) configured
as either one screen, two screens, or virtual screens. The pixel
combiner is also responsible for generating some of the control signals
for the pixel link output channel. For now, the driver only supports
the bypass mode.
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Colibri iMX8X, LT170410-2WHC, LP156WF1
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220611141421.718743-5-victor.liu@nxp.com
