Commit 56d8ce9d8c ("drm/amd/display: Apply correct panel mode when
reinitializing hardware") made ASSR failure fall back to the default panel
mode unless eDP mode had previously been applied.
However, dc_link is zero-initialized and DP_PANEL_MODE_DEFAULT is zero.
Before the first call to dp_set_panel_mode(), panel_mode therefore looks
like a previously applied default mode. If ASSR setup fails during the
first link training attempt, the driver incorrectly trains the eDP link
using the default scrambling mode.
On a Google Vilboz Chromebook running self-built coreboot firmware and
PSP verstage, this leaves the panel mostly black with corrupted output
along the top edge.
Track whether panel_mode has actually been initialized, and only consult
the saved mode after it has been applied. This retains the recovery
behavior while preserving eDP mode during initial link training.
Fixes: 56d8ce9d8c ("drm/amd/display: Apply correct panel mode when reinitializing hardware")
Assisted-by: Pi:gpt-5.6-sol
Reviewed-by: George Zhang <george.zhang@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit ccb6c2702033f1002b45807fb3cc938760f26f78)
Cc: stable@vger.kernel.org # 6.4.x
get_estimated_bw() divides by link->dpia_bw_alloc_config.bw_granularity,
which is zeroed by reset_bw_alloc_struct() and only populated once
DP_TUNNELING_BW_ALLOC_CAP_CHANGED has been handled.
link_dp_dpia_handle_bw_alloc_status(), the DPCD interrupt handler,
calls get_estimated_bw() whenever DP_TUNNELING_ESTIMATED_BW_CHANGED
is set, independently of whether DP_TUNNELING_BW_ALLOC_CAP_CHANGED
has ever fired for that link. A connected USB4/DPIA tunneling device
that reports an estimated-bandwidth change before ever reporting a
capability change drives a division by zero in this IRQ path.
link_dpia_send_bw_alloc_request() already guards the same
bw_granularity division; add the identical guard here rather than
introducing a new pattern.
Fixes: 8e5cfe547b ("drm/amd/display: upstream link_dp_dpia_bw.c")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Assisted-by: gkh_clanker_t1000
Signed-off-by: Hari Mishal <harimishal1@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f2a961457c33dc34223aad5c9e8971de34a4eed3)
Cc: stable@vger.kernel.org
After a refactor that landed in Linux 7.0,
DC now crashes when it is initialized on GPUs
that have a VGA or LVDS connector. This is because
these connectors have no HPD so the hpd_gpio is NULL
and therefore DC takes the code path meant for
DCN 4.2+ which sets irq_source_hpd = 255 that
causes the subsequent code to try to register
the HPD interrupt, which fails, and causes
a crash.
This commit should be backported to Linux 7.0 and newer.
Cc: stable@vger.kernel.org
Cc: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Cc: Roman Li <roman.li@amd.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/5490
Fixes: def3488eb0 ("drm/amd/display: refactor HPD to increase flexibility")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Link: https://patch.msgid.link/20260821215059.312868-1-timur.kristof@gmail.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
ensure dtbclk is enabled before hdmistreamclk_en
pmfw could stop dtbclk on idle.
driver needs to ensure dtbclk enabled is enabled before hdmistreamclk_en
also disable debounce timer on dcn42.
Reviewed-by: Chris Park <chris.park@amd.com>
Reviewed-by: Leo Chen <leo.chen@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add hooks in various entry points to perform hw/sw init for DCN6 asic
- Add dependent changes needed to enable DCN6 asic
- Update the Makefiles so that DCN6 related newly added sources are compiled
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit a4f01bf729 ("drm/amd/display: Refactor and fix link_dpms I2C")
had also changed the "Set retimer failed" messages from DC_LOG_DEBUG()
to DC_LOG_ERROR(). This unfortunately can create log spam.
Change those back to DC_LOG_DEBUG() only.
Fixes: a4f01bf729 ("drm/amd/display: Refactor and fix link_dpms I2C")
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/5520
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
- force FRL rate debug bit was not correctly forcing requested FRL rate
Reviewed-by: Chris Park <chris.park@amd.com>
Signed-off-by: Relja Vojvodic <Relja.Vojvodic@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Ongoing optimization efforts require splitting DPMS ON around
enable_link, in order to enable running multiple sequences
in parallel.
[How]
* Split link_set_dpms_on across enable_link
* Add return value indicating whether the programming sequence
succeeded and/or run to the end.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dominik Kaszewski <dominik.kaszewski@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
The final DP LT failure meant to be logged as DC warning is skipped due
to a break statement above. Move logging up to make sure we don't miss
LT fail events.
Reviewed-by: George Shen <george.shen@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
link_dp_irq_handler.c includes "link_dp_panel_replay.h" twice. Drop the
redundant second include; this is a non-functional cleanup flagged by
scripts/checkincludes.pl.
Fixes: 1e5cd4adfc ("drm/amd/display: move panel replay out from edp")
Signed-off-by: Anas Khan <anxkhn28@gmail.com>
Reviewed-by: George Zhang <george.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
TCONs supporting VESA AUX Backlight does not always
support VESA Smooth Brightness. Driver software
needs to implement smooth brightness by periodically
updating the brightness by small steps. Driver
implementation is completed and verified on LCD
panels but solution is missing for OLED panels.
[How]
Updated driver to include smooth brightness for
OLED panels using VESA Aux Backlight.
Revert original workaround for VABC on oled issue,
as it is no longer needed.
Add VABC backlight Initialization sequence from
driver side.
Add fix to remove conflict between FW and driver
backlight programming for future ASIC.
Enable VABC for all future asic revisions.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Iswara Nagulendran <Iswara.Nagulendran@amd.com>
Signed-off-by: George Zhang <george.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No functional changes. Just clean up a conceptual mismatch.
Based on feedback on the NUTMEG code in DC, the
preferred_link_setting is meant to force the DP link to a
specific setting, meaning both the link rate and lane count
should be locked to an exact value. What NUTMEG needs is
a lower bound on the link rate, which is not the same concept.
Implement this as a HW workaround flag instead.
Suggested-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When there is a preferred link rate setting, it needs to be
applied to both the current and initial link rate.
This was regressed by a "coding style" fix, which caused
the current link rate to not respect the preferred value.
This commit restores the functionality of NUTMEG,
the DP bridge encoder found on old APUs such as Kaveri.
Fixes: a62346043a ("drm/amd/display: Fix coding style issue")
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/5465
Cc: Chuanyu Tseng <Chuanyu.Tseng@amd.com>
Reviewed-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
stream->sink is optional and can be null, so should always be checked
before dereference. Additionally, most of its usage in DPMS sequences
is for stream->sink->link, which can be replaced with stream->link,
as the two should always be the same.
[How]
* Replace stream->sink->link in DPMS on/off
* Add assert to USB4 BW allocation where sink is required
* Avoid inconsistencies in resource access, e.g. don't repeat
stream->link after it was already saved to a local variable
* Pull out effective VPG calculation to helper getter
* Formatting fixes
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Dominik Kaszewski <dominik.kaszewski@amd.com>
Signed-off-by: George Zhang <george.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need special handling for passive HDMI dongles with I2C over AUX.
Reviewed-by: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Signed-off-by: Matthew Stewart <Matthew.Stewart2@amd.com>
Signed-off-by: George Zhang <george.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
prev_sink is unconditionally retained via dc_sink_retain at function
entry, but the DP alt mode timeout path inside SIGNAL_TYPE_DISPLAY_PORT
returns false without releasing prev_sink. All other return paths in the
function correctly call dc_sink_release(prev_sink), making this the only
missing cleanup.
Fixes: 54618888d1 ("drm/amd/display: break down dc_link.c")
Signed-off-by: WenTao Liang <vulab@iscas.ac.cn>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Link: https://patch.msgid.link/20260626124555.36910-1-vulab@iscas.ac.cn
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The compound condition checking dp_connector_no_native_i2c
and no_ddc_pin was duplicated across many files, obscuring
intent at every call site.
[How]
Add bool force_i2c_over_aux to struct dc_link, initialized
once during link creation. Add link_get_ddc_aux_inst()
helper to select the correct aux instance. Wire into
link_service via construct_link_service_ddc(). Replace all
duplicated condition checks and aux instance selection
blocks with the new field and helper. No functional change.
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Zhang <george.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
- Added link bw to switch case
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Relja Vojvodic <Relja.Vojvodic@amd.com>
Signed-off-by: George Zhang <george.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
'skip_frl_pretraining' was introduced and enabled along w/ HDMI 2.1
initial upstream, but is causing HDMI validation link training to be s
kipped on short hotplugs and compliance issues.
Remove this behaviour to force link training on all hotplugs for all
ASICs.
Reviewed-by: Relja (Reggie) Vojvodic <relja.vojvodic@amd.com>
Reviewed-by: Sun peng (Leo) Li <sunpeng.li@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Signed-off-by: George Zhang <george.zhang@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Enable PSR and Panel Replay on a DCN4 variant for display power
savings. On links without native I2C (no DDC pin), the AUX channel
must use aux_hw_inst to avoid NULL pointer access during PSR and
Replay setup.
[How]
Enable PSR and Replay in the DCN4 variant panel config defaults.
Add no_ddc_pin check in dp_setup_panel_replay(),
edp_setup_freesync_replay(), and fsft_send_msg_to_fw() to use
link->aux_hw_inst when dp_connector_no_native_i2c and no_ddc_pin
are set.
Reviewed-by: Matthew Stewart <matthew.stewart2@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Signed-off-by: George Zhang <george.zhang@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The PSRSU-RC capability should be populated in DC during edp detection.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Robin Chen <robin.chen@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add all the bits to enable DSC over FRL.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Start bringing in the protocol layer for FRL in DC link.
This includes FRL training, timing validation, and other
protocol bits.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ASICs which do not have native DDC capability must use a different
codepath to access the AUX channel.
[How]
- BIOS cap NO_DDC_PIN is set to 1 for links which do not have the DDC pin.
- dp_connector_no_native_i2c in dc_config must also be set to true to
use this codepath.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Matthew Stewart <Matthew.Stewart2@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Calling dc_update_planes_and_stream separately for stream and its
phantom stream causes a NULL pointer dereference, since the phantom is
destroyed on the first call.
Skip the call for phantom streams.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Add a new debug option "enable_replay_esd_recovery" to control whether
to enable the replay ESD recovery feature.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Wei-Guang Li <wei-guang.li@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
Add Auxless-ALPM data in VESA PR initialization
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Leon Huang <Leon.Huang1@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The MST overhead was incorrectly included
in the requested BW during BW deallocation.
[How]
Exclude the MST overhead from BW deallocation.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some eDP panels return sinkstatus as 0x5, causing the original sinkstatus == 1
check to never match and resulting in unnecessary polling delay. The
equality check is too restrictive and doesn't properly validate the
specific status bit that indicates receiver readiness.
[How]
Replace direct value comparison with proper bitmask check using
DP_RECEIVE_PORT_0_STATUS constant.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Sung-huai Wang <Danny.Wang@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The logic for choosing between the dce_aux_transfer function variants is
moved into dce_aux.c rather than link_ddc.c.
The "dce_aux_transfer_with_retries" function now uses
dce_aux_transfer_raw in its implementation as the logic is equivalent.
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Reviewed-by: Gabe Teeger <gabe.teeger@amd.com>
Signed-off-by: Matthew Stewart <Matthew.Stewart2@amd.com>
Signed-off-by: James Lin <pinglei.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Fix various warnings related to unsigned/signed mismatches
- Consistently use the same signedness for a given value
- Explcitly cast between types when needed
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Clay King <clayking@amd.com>
Signed-off-by: James Lin <pinglei.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Address signed/unsigned comparison warnings across dc paths to keep
builds warning-clean and improve type safety at comparison boundaries.
Most warnings came from signed loop/index temporaries compared against
unsigned counters and table sizes, plus a smaller number of mixed
signed/unsigned clock, bandwidth, and geometry comparisons.
[How]
Aligned iterator and temporary variable types with the semantic type
of the compared bounds. Used unsigned indices for loops bounded by unsigned
counters and table sizes, while retaining signed types where values are
semantically signed or participate in arithmetic that may legitimately go
negative. Where mixed signed/unsigned comparisons are intentional, applied
explicit boundary casts or guarded comparisons instead of broad type
changes.
No functional behavior changes are intended; this is a warning-resolution
and type-alignment cleanup.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Gaghik Khachatrian <gaghik.khachatrian@amd.com>
Signed-off-by: James Lin <pinglei.lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
The 'state' parameter in enable_link_analog() is never used
within the function body. Remove it from the function.
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: James Lin <pinglei.lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On some laptops, the embedded panel may not have
a DDC (display data channel) available. On these,
the EDID may be hardcoded in ACPI or the VBIOS.
In this case, use GPIO_DDC_LINE_UNKNOWN and don't fail.
Fixes: def3488eb0 ("drm/amd/display: refactor HPD to increase flexibility")
Link: https://gitlab.freedesktop.org/drm/amd/-/work_items/5192
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] drm/amd/display had implicit integer narrowing at protocol/storage boundaries
and an incomplete eDP assignment in integrated info parsing.
[How] Apply explicit boundary casts for intentional narrowing, keep intermediate math
in wider types, and restore explicit eDP field mapping in v2.2 parser.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Gaghik Khachatrian <gaghik.khachatrian@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
To avoid unnecessary link retraining when the panel is in Replay/PSR mode,
we need to check if it's in active state and ESD information before we
decide to retrain the link.
Reviewed-by: ChunTao Tso <chuntao.tso@amd.com>
Signed-off-by: Allen Li <allen.li@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
There will be an unexpected desync error while doing PSR -> Replay transit,
so we want to disable the replay desync error detection by default.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Signed-off-by: Allen Li <allen.li@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Function logic should put after variable declare section, so let's move it.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Chuanyu Tseng <Chuanyu.Tseng@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If EDID AMD VSDB declares that sink supports MCCS method for freesync
usage, send mccs request to understand sink freesync current supporting
state.
If sink supports freesync but user toggles OSD to turn off it, disable
freesync.
If HDMI sink doesn't support MCCS method for freesync usage, disable
freesync as well.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Reworked YCbCr4:2:2 Native/Simple policy decision making with DSC
enabled based on DSC caps and stream signal type
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Relja Vojvodic <Relja.Vojvodic@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Resolve compiler warnings by marking unused parameters explicitly.
[How]
In .c and .h function definitions, keep parameter names
in signatures and add a line with `(void)param;` in function body
Preserved function signatures and avoids breaking code paths that
may reference the parameter under conditional compilation.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Austin Zheng <austin.zheng@amd.com>
Signed-off-by: Gaghik Khachatrian <gaghik.khachatrian@amd.com>
Signed-off-by: Chuanyu Tseng <chuanyu.tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To support specific sequencing requirements for DPIA link output
[How]
Implement the dpia_link_hwss structure and define the necessary
control function pointers. The initialization order is
aligned with the core link_hwss definition to ensure consistency
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Lincheng Ku <LinCheng.Ku@amd.com>
Signed-off-by: Chuanyu Tseng <chuanyu.tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Reworked YCbCr4:2:2 Native/Simple policy decision making with DSC
enabled based on DSC caps and stream signal type
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Relja Vojvodic <Relja.Vojvodic@amd.com>
Signed-off-by: Chuanyu Tseng <chuanyu.tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for DCN 4.2 clock manager.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Silence warning by cleaning up unused code.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Clay King <clayking@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[HOW]
Add Replay recovery flow so that when HPD occurs and ESD is detected,
Replay can restore the system back to normal.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Robin Chen <robin.chen@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Weiguang Li <wei-guang.li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
