GPIO core:
- extend the gpio-regmap abstraction layer with more features allowing users
to override configuration setting, translate register values and masks and
enable/disable interrupts
- extend GPIO kunit tests with suites verifying probe ordering by software
node devlink support and software node hogs
- shrink GPIO kunit initialization code
- coding style updates (remove commas from sentinels where applicable)
- with all users now converted treewide to using real firmware node links for
software node GPIO lookup: remove the deprecated label-matching mechanism
from from GPIO core
- drop redundant return value check of nonseekable_open() in gpiolib-cdev
- use IRQ trigger helpers where applicable
Driver updates:
- refactor error paths and logging in gpio-nomadik
- use more modern interfaces for getting resources in gpio-rockchip,
gpio-bt8xx and gpio-pca9570
- add missing MODULE_DEVICE_TABLE() to gpio-sifive and gpio-vf610
- drop unused FILONOFF macro from gpio-rcar
- extend build coverage of ioport GPIO drivers with COMPILE_TEST=y
- only enable the gpio-rtd driver by default with ARCH_REALTEK=y to avoid
bloating the build
- refactor coding style in several drivers
- use correct endianess translation in gpio-pcf85x
- add wake-up interrupt support to gpio-mvebu
- apply initial value in direction output setter in gpio-by-pinctrl
Misc:
- replace linux/gpio.h inclusions treewide with linux/gpio/legacy.h which now
exports all the deprecated APIs
- select GPIOLIB_LEGACY in Kconfig where required treewide
- use software nodes for gpio-keys in MFD drivers
Devicetree bindings:
- describe the realtek rtd1625 GPIO controller
- document new models for gpio-pca95xx and gpio-cadence
- document new property in gpio-rockchip
-----BEGIN PGP SIGNATURE-----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=rUDt
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v7.3-rc1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"GPIO core:
- extend the gpio-regmap abstraction layer with more features
allowing users to override configuration setting, translate
register values and masks and enable/disable interrupts
- extend GPIO kunit tests with suites verifying probe ordering by
software node devlink support and software node hogs
- shrink GPIO kunit initialization code
- coding style updates (remove commas from sentinels where
applicable)
- with all users now converted treewide to using real firmware node
links for software node GPIO lookup: remove the deprecated
label-matching mechanism from from GPIO core
- drop redundant return value check of nonseekable_open() in
gpiolib-cdev
- use IRQ trigger helpers where applicable
Driver updates:
- refactor error paths and logging in gpio-nomadik
- use more modern interfaces for getting resources in gpio-rockchip,
gpio-bt8xx and gpio-pca9570
- add missing MODULE_DEVICE_TABLE() to gpio-sifive and gpio-vf610
- drop unused FILONOFF macro from gpio-rcar
- extend build coverage of ioport GPIO drivers with COMPILE_TEST=y
- only enable the gpio-rtd driver by default with ARCH_REALTEK=y to
avoid bloating the build
- refactor coding style in several drivers
- use correct endianess translation in gpio-pcf85x
- add wake-up interrupt support to gpio-mvebu
- apply initial value in direction output setter in gpio-by-pinctrl
Misc:
- replace linux/gpio.h inclusions treewide with linux/gpio/legacy.h
which now exports all the deprecated APIs
- select GPIOLIB_LEGACY in Kconfig where required treewide
- use software nodes for gpio-keys in MFD drivers
Devicetree bindings:
- describe the realtek rtd1625 GPIO controller
- document new models for gpio-pca95xx and gpio-cadence
- document new property in gpio-rockchip"
* tag 'gpio-updates-for-v7.3-rc1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (61 commits)
gpio: gpio-by-pinctrl: Apply initial value in direction output wrapper
dt-bindings: gpio: rockchip,gpio-bank: Add rockchip,grf property
gpio: Use IRQ trigger mask helpers
gpio: allow COMPILE_TEST for IOPORT drivers
gpio: realtek: Add driver for Realtek DHC RTD1625 SoC
gpio: regmap: Add IRQ enable/disable helpers
gpio: regmap: Add set_config callback
gpio: regmap: Add value_xlate callback
gpio: regmap: Add gpio_regmap_operation to extend reg_mask_xlate callback
gpio: regmap: Order kernel-doc descriptions with the actual appearance
gpio: regmap: Apply default resource callbacks for regmap IRQ chip
gpio: regmap: Provide default IRQ resource request and release callbacks
Revert "gpio: realtek: Add driver for Realtek DHC RTD1625 SoC"
gpib: gpio: replace linux/gpio.h inclusion
Input: matrix_keyboard - replace linux/gpio.h inclusion
phy: replace linux/gpio.h inclusions
pcmcia: replace linux/gpio.h inclusions
ASoC: replace linux/gpio.h inclusions
mfd: replace linux/gpio.h inclusions
sh: replace linux/gpio.h inclusions
...
Move the ppc4xx gpio driver out of arch/powerpc/platforms/44x/ into
drivers/gpio/gpio-ppc44x.c. The driver has no architecture-specific
dependencies and follows the same pattern as other PowerPC GPIO
drivers already in drivers/gpio/ (e.g. gpio-mpc8xxx, gpio-mpc5200).
- Renamed Kconfig symbol from PPC4xx_GPIO to GPIO_PPC44X
- Updated ppc44x_defconfig and warp_defconfig to use the new symbol
- Marked the new option as tristate (was bool) since the driver
supports module build via module_platform_driver()
Assisted-by: opencode:big-pickle
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260803223539.86303-2-rosenp@gmail.com
Add support for the GPIO controller found on Realtek DHC RTD1625 SoCs.
Unlike the existing Realtek GPIO driver (drivers/gpio/gpio-rtd.c),
which manages pins via shared bank registers, the RTD1625 introduces
a per-pin register architecture. Each GPIO line now has its own
dedicated 32-bit control register to manage configuration independently,
including direction, output value, input value, interrupt enable, and
debounce. Therefore, this distinct hardware design requires a separate
driver.
The RTD1625 GPIO controller has a hardware quirk where both 'assert'
and 'de-assert' interrupts are fired simultaneously on any edge toggle.
The driver works around this quirk to correctly handle edge interrupts.
Interrupt support is optional for this device, matching the dt-bindings.
If the interrupts property is not provided, the driver simply skips IRQ
initialization and operates purely as a basic GPIO controller.
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Tzuyi Chang <tychang@realtek.com>
Co-developed-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Reviewed-by: Mathieu Dubois-Briand <mathieu.dubois-briand@bootlin.com>
Link: https://patch.msgid.link/20260726125209.140307-10-eleanor.lin@realtek.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
This reverts commit a57e27c43b.
The driver will be rewritten to use the gpio-regmap infrastructure
once Andy Shevchenko's patches for gpio-regmap are applied.
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Link: https://patch.msgid.link/20260726125209.140307-2-eleanor.lin@realtek.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Add support for the GPIO controller found on Realtek DHC RTD1625 SoCs.
Unlike the existing Realtek GPIO driver (drivers/gpio/gpio-rtd.c),
which manages pins via shared bank registers, the RTD1625 introduces
a per-pin register architecture. Each GPIO line now has its own
dedicated 32-bit control register to manage configuration independently,
including direction, output value, input value, interrupt enable, and
debounce. Therefore, this distinct hardware design requires a separate
driver.
Additionally, the RTD1625 GPIO controller has a specific hardware quirk:
it fires both 'assert' and 'de-assert' interrupts simultaneously on any
edge toggle. To handle this, we utilize the polarity register to route
the requested edge (rising/falling) to the 'assert' IRQ line. The driver
then filters out the unwanted 'de-assert' interrupt in the IRQ handler
and pre-clears edge interrupts to prevent interrupt storms caused by
unhandled dropped interrupts.
Interrupt support is optional for this device, matching the dt-bindings.
If the interrupts property is not provided, the driver simply skips IRQ
initialization and operates purely as a basic GPIO controller.
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Tzuyi Chang <tychang@realtek.com>
Co-developed-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Signed-off-by: Yu-Chun Lin <eleanor.lin@realtek.com>
Link: https://patch.msgid.link/20260622092335.1166876-4-eleanor.lin@realtek.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
* New drivers for the following chips
- Analog Devices LTC4283 Swap Controller
- Analog Devices MAX20830
- Analog Devices MAX20860A
- ARCTIC Fan Controller
- Delta E50SN12051
- Luxshare LX1308
- Microchip EMC1812/13/14/15/33
- Monolithic MP2985
- Murata D1U74T PSU
* New chip support added to existing drivers
- asus-ec-sensors: Support for ROG MAXIMUS Z790 EXTREME, ROG STRIX B850-E
GAMING WIFI, and ROG STRIX B650E-E GAMING WIFI
- dell-smm: Add Dell Latitude 7530 to fan control whitelist
- nct6683: Support for ASRock Z890 Pro-A
- pmbus: Support for Flex BMR316, BMR321, BMR350 and BMR351
- pmbus/max34440: Support for ADPM12250
- pmbus/xdp720: Support for Infineon xdp730, and fix driver issues
reported by Sashiko
* New functionality
- Add support for update_interval_us chip attribute, and support it
in ina238 driver
- Add support for guard() and scoped_guard() for subsystem locks,
and use it in adt7411, ina2xx, and lm90 drivers
- emc2305: Support configurable fan PWM at shutdown
- lm63: Expose PWM frequency and LUT hysteresis as writable
- lm75: Support active-high alert polarity
- nct7802: Add time step attributes for tweaking responsiveness
- pmbus/adm1266: Add rtc debugfs entries for rtc, powerup_counter,
clear_blackbox, and firmware_revision
- raspberrypi: Fix delayed-work teardown race, add voltage input support
as well as voltage domain IDs
mcp9982: Add support for reporting external diode faults
* Miscellaneous bug fixes, changes and improvements
- Use named initializers for platform_device_id arrays and
i2c_device_data, and remove unused driver data
- Various drivers: Move MODULE_DEVICE_TABLE next to the table itself
- ads7871: Convert to hwmon_device_register_with_info(), and use
DMA-safe buffer for SPI writes
- adt7411: document supported sysfs attributes
- adt7462: Add of_match_table to support devicetree
- adt7475: Add explicit header include
- coretemp; Fix outdated documentation, coding style issues, and
replace hardcoded core count with dynamic value
- cros_ec: Drop unused assignment of platform_device_id driver data
- emc2305: Fix fan channel index handling
- gpd-fan: Reject EC PWM value 0 as invalid, fix race condition between
device removal and sysfs access, upgrade log level from warn to err for
platform device creation failure, initialize EC before registering hwmon
device, drop global driver data and use per-device allocation
- htu31: document debugfs serial_number
- ina238: Add support for samples and update_interval
- it87: Clamp negative values to zero in set_fan()
- lm75: Add explicit header include, Add explicit default cases in
lm75_is_visible(), and add section for sysfs interface to documentation
- pmbus/lm25066: Fix PMBus coefficients for LM5064/5066/5066i
- tmp102: Use device_property_read_string API
- tmp401: Read "ti,n-factor" as signed
- Convert zyxel,nsa320-mcu to DT schema
-----BEGIN PGP SIGNATURE-----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=mDMd
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers for the following chips:
- Analog Devices LTC4283 Swap Controller
- Analog Devices MAX20830
- Analog Devices MAX20860A
- ARCTIC Fan Controller
- Delta E50SN12051
- Luxshare LX1308
- Microchip EMC1812/13/14/15/33
- Monolithic MP2985
- Murata D1U74T PSU
New chip support added to existing drivers:
- asus-ec-sensors: Support for ROG MAXIMUS Z790 EXTREME, ROG STRIX
B850-E GAMING WIFI, and ROG STRIX B650E-E GAMING WIFI
- dell-smm: Add Dell Latitude 7530 to fan control whitelist
- nct6683: Support for ASRock Z890 Pro-A
- pmbus: Support for Flex BMR316, BMR321, BMR350 and BMR351
- pmbus/max34440: Support for ADPM12250
- pmbus/xdp720: Support for Infineon xdp730, and fix driver issues
reported by Sashiko
New functionality:
- Add support for update_interval_us chip attribute, and support it
in ina238 driver
- Add support for guard() and scoped_guard() for subsystem locks, and
use it in adt7411, ina2xx, and lm90 drivers
- emc2305: Support configurable fan PWM at shutdown
- lm63: Expose PWM frequency and LUT hysteresis as writable
- lm75: Support active-high alert polarity
- nct7802: Add time step attributes for tweaking responsiveness
- pmbus/adm1266: Add rtc debugfs entries for rtc, powerup_counter,
clear_blackbox, and firmware_revision
- raspberrypi: Fix delayed-work teardown race, add voltage input
support as well as voltage domain IDs
- mcp9982: Add support for reporting external diode faults
Miscellaneous bug fixes, changes and improvements:
- Use named initializers for platform_device_id arrays and
i2c_device_data, and remove unused driver data
- Various drivers: Move MODULE_DEVICE_TABLE next to the table itself
- ads7871: Convert to hwmon_device_register_with_info(), and use
DMA-safe buffer for SPI writes
- adt7411: document supported sysfs attributes
- adt7462: Add of_match_table to support devicetree
- adt7475: Add explicit header include
- coretemp; Fix outdated documentation, coding style issues, and
replace hardcoded core count with dynamic value
- cros_ec: Drop unused assignment of platform_device_id driver data
- emc2305: Fix fan channel index handling
- gpd-fan: Reject EC PWM value 0 as invalid, fix race condition
between device removal and sysfs access, upgrade log level from
warn to err for platform device creation failure, initialize EC
before registering hwmon device, drop global driver data and use
per-device allocation
- htu31: document debugfs serial_number
- ina238: Add support for samples and update_interval
- it87: Clamp negative values to zero in set_fan()
- lm75: Add explicit header include, Add explicit default cases in
lm75_is_visible(), and add section for sysfs interface to
documentation
- pmbus/lm25066: Fix PMBus coefficients for LM5064/5066/5066i
- tmp102: Use device_property_read_string API
- tmp401: Read "ti,n-factor" as signed
- Convert zyxel,nsa320-mcu to DT schema"
* tag 'hwmon-for-v7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (81 commits)
hwmon: tmp401: Read "ti,n-factor" as signed
hwmon: (pmbus/lm25066) Fix PMBus coefficients for LM5064/5066/5066i
hwmon: (gpd-fan) Reject EC PWM value 0 as invalid
hwmon: (dell-smm) Add Dell Latitude 7530 to fan control whitelist
hwmon: temperature: add support for EMC1812
dt-bindings: hwmon: temperature: add support for EMC1812
hwmon: (gpd-fan): fix race condition between device removal and sysfs access
hwmon: (gpd-fan): upgrade log level from warn to err for platform device creation failure
hwmon: (gpd-fan): Initialize EC before registering hwmon device
hwmon: (gpd-fan): drop global driver data and use per-device allocation
hwmon: (pmbus/max34440): add support adpm12250
hwmon: (ina238) Add update_interval_us attribute
hwmon: Add update_interval_us chip attribute
hwmon: (ina238) Add support for samples and update_interval
gpio: gpio-ltc4283: Add support for the LTC4283 Swap Controller
hwmon: ltc4283: Add support for the LTC4283 Swap Controller
dt-bindings: hwmon: Document the LTC4283 Swap Controller
hwmon: (pmbus/xdp720) Fix driver issues xdp720/730
hwmon: (pmbus/xdp720) Add support for efuse xdp730
dt-bindings: hwmon/pmbus: Add Infineon xdp730
...
The LTC4283 device has up to 8 pins that can be configured as GPIOs.
Note that PGIO pins are not set as GPIOs by default so if they are
configured to be used as GPIOs we need to make sure to initialize them
to a sane default. They are set as inputs by default.
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20260502-ltc4283-support-v13-3-1c206542e652@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ts5500 platform is no longer functional because it is
based on the removed AMD Élan i486 SoC. Remove the now
obsolete driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260526103424.3246915-1-arnd@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Add a module containing kunit test cases for GPIO core. The idea is to
use it to test functionalities that can't easily be tested from
user-space with kernel selftests or GPIO character device test suites
provided by the libgpiod package.
For now add test cases that verify software node based lookup and ensure
that a GPIO provider unbinding with active consumers does not cause a
crash.
Reviewed-by: David Gow <david@davidgow.net>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260522-gpiolib-kunit-v3-3-b15fe6987430@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
The Waveshare DSI TOUCH family of panels has separate on-board GPIO
controller, which controls power supplies to the panel and the touch
screen and provides reset pins for both the panel and the touchscreen.
Also it provides a simple PWM controller for panel backlight. Add
support for this GPIO controller.
Tested-by: Riccardo Mereu <r.mereu@arduino.cc>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260507-waveshare-dsi-touch-v5-2-d2ac7ccc22d4@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
This driver provides support for new way of handling platform events,
through the use of GPIO-signaled ACPI events. This mechanism is used on
Intel client platforms released in 2026 and later, starting with Intel
Nova Lake.
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260401174526.60881-1-alan.borzeszkowski@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
The ARM SCMI pinctrl protocol allows GPIO access. Instead of creating
a new SCMI GPIO driver, this driver is a generic GPIO driver that uses
standard pinctrl interfaces.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
The ROHM BD72720 has 6 pins which may be configured as GPIOs. The
GPIO1 ... GPIO5 and EPDEN pins. The configuration is done to OTP at the
manufacturing, and it can't be read at runtime. The device-tree is
required to tell the software which of the pins are used as GPIOs.
Keep the pin mapping static regardless the OTP. This way the user-space
can always access the BASE+N for GPIO(N+1) (N = 0 to 4), and BASE + 5
for the EPDEN pin. Do this by setting always the number of GPIOs to 6,
and by using the valid-mask to invalidate the pins which aren't configured
as GPIOs.
First two pins can be set to be either input or output by OTP. Direction
can't be changed by software. Rest of the pins can be set as outputs
only. All of the pins support generating interrupts.
Support the Input/Output state getting/setting and the output mode
configuration (open-drain/push-pull).
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/22e095ca92f0677ca3d3a768ad749629fc3c2006.1765804226.git.mazziesaccount@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add a new driver which provides a 1-to-many mapping for a single real
GPIO using a multiplexer. Each virtual GPIO corresponds to a multiplexer
state which, if set for the multiplexer, connects the real GPIO to the
corresponding virtual GPIO.
This can help in various usecases. One practical case is the special
hardware design of the Realtek-based XS1930-10 switch from Zyxel. It
features two SFP+ ports/cages whose signals are wired directly to the
switch SoC. Although Realtek SoCs are short on GPIOs, there are usually
enough the fit the SFP signals without any hacks.
However, Zyxel did some weird design and connected RX_LOS, MOD_ABS and
TX_FAULT of one SFP cage onto a single GPIO line controlled by a
multiplexer (the same for the other SFP cage). The single multiplexer
controls the lines for both SFP and depending on the state, the
designated 'signal GPIO lines' are connected to one of the three SFP
signals.
Because the SFP core/driver doesn't support multiplexer but needs single
GPIOs for each of the signals, this driver fills the gap between both.
It registers a gpio_chip, provides multiple virtual GPIOs and sets the
backing multiplexer accordingly.
Due to several practical issues, this is input-only and doesn't support
IRQs.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Reviewed-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251227180134.1262138-3-jelonek.jonas@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Add better support for GPIOs shared by multiple consumers.
-----BEGIN PGP SIGNATURE-----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=fa8j
-----END PGP SIGNATURE-----
Merge tag 'gpio/shared-gpios-for-v6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux.git into gpio/for-next
Immutable branch between the GPIO, ASoC and regulator trees for v6.19-rc1
Add better support for GPIOs shared by multiple consumers.
Add a virtual GPIO proxy driver which arbitrates access to a single
shared GPIO by multiple users. It works together with the core shared
GPIO support from GPIOLIB and functions by acquiring a reference to a
shared GPIO descriptor exposed by gpiolib-shared and making sure that
the state of the GPIO stays consistent.
In general: if there's only one user at the moment: allow it to do
anything as if this was a normal GPIO (in essence: just propagate calls
to the underlying real hardware driver). If there are more users: don't
allow to change the direction set by the initial user, allow to change
configuration options but warn about possible conflicts and finally:
treat the output-high value as a reference counted, logical "GPIO
enabled" setting, meaning: the GPIO value is set to high when the first
user requests it to be high and back to low once the last user stops
"voting" for high.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251112-gpio-shared-v4-4-b51f97b1abd8@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This module scans the device tree (for now only OF nodes are supported
but care is taken to make other fwnode implementations easy to
integrate) and determines which GPIO lines are shared by multiple users.
It stores that information in memory. When the GPIO chip exposing shared
lines is registered, the shared GPIO descriptors it exposes are marked
as shared and virtual "proxy" devices that mediate access to the shared
lines are created. When a consumer of a shared GPIO looks it up, its
fwnode lookup is redirected to a just-in-time machine lookup that points
to this proxy device.
This code can be compiled out on platforms which don't use shared GPIOs.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251112-gpio-shared-v4-3-b51f97b1abd8@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add support for the GPIO controller found on some QIXIS FPGAs in
Layerscape boards such as LX2160ARDB and LS1046AQDS. This driver is
using gpio-regmap.
A GPIO controller has a maximum of 8 lines (all found in the same
register). Even within the same controller, the GPIO lines' direction is
fixed, which mean that both input and output lines are found in the same
register. This is why the driver also passed to gpio-regmap the newly
added .fixed_direction_output bitmap to represent the true direction of
the lines.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Michael Walle <mwalle@kernel.org> # for the gpio-regmap part
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Here is the big set of USB and thunderbolt drivers for 6.18-rc1. It was
another normal development cycle, with lots of the usual drivers getting
updates:
- Thunderbolt driver cleanups and additions
- dwc3 driver updates
- dwc2 driver updates
- typec driver updates
- xhci driver updates and additions
- offload USB engine updates for better power management
- unused tracepoint removals
- usb gadget fixes and updates as more users start to rely on these
drivers instead of the "old" function gadget drivers
- new USB device ids
- other minor driver USB driver updates
- new USB I/O driver framework and driver additions
The last item, the usb i/o driver, has an i2c and gpio driver added
through this tree. Those drivers were acked by the respective subsystem
maintainers, but you will get a merge conflict with the i2c tree where
new drivers were added in the same places in a Kconfig and Makefile.
The merge conflict is simple, just take both sides.
All of these have been in linux-next for a while, with the only issue
being the i2c tree merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaOEo8Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynpOQCgkenJzjsGVHhl/tm447z3pQ8NtvQAn2GfxMF9
4jQlUtr6McyzCLVPOZRD
=pPei
-----END PGP SIGNATURE-----
Merge tag 'usb-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and thunderbolt drivers for 6.18-rc1. It
was another normal development cycle, with lots of the usual drivers
getting updates:
- Thunderbolt driver cleanups and additions
- dwc3 driver updates
- dwc2 driver updates
- typec driver updates
- xhci driver updates and additions
- offload USB engine updates for better power management
- unused tracepoint removals
- usb gadget fixes and updates as more users start to rely on these
drivers instead of the "old" function gadget drivers
- new USB device ids
- other minor driver USB driver updates
- new USB I/O driver framework and driver additions"
The last item, the usb i/o driver, has an i2c and gpio driver added
through this tree. Those drivers were acked by the respective
subsystem maintainers.
All of these have been in linux-next for a while"
* tag 'usb-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (132 commits)
usb: vhci-hcd: Prevent suspending virtually attached devices
USB: serial: option: add SIMCom 8230C compositions
thunderbolt: Fix use-after-free in tb_dp_dprx_work
usb: xhci: align PORTSC trace with one-based port numbering
usb: xhci: correct indentation for PORTSC tracing function
usb: xhci: improve TR Dequeue Pointer mask
usb: xhci-pci: add support for hosts with zero USB3 ports
usb: xhci: Update a comment about Stop Endpoint retries
Revert "usb: xhci: Avoid Stop Endpoint retry loop if the endpoint seems Running"
usb: gadget: f_rndis: Refactor bind path to use __free()
usb: gadget: f_ecm: Refactor bind path to use __free()
usb: gadget: f_acm: Refactor bind path to use __free()
usb: gadget: f_ncm: Refactor bind path to use __free()
usb: gadget: Introduce free_usb_request helper
usb: gadget: Store endpoint pointer in usb_request
usb: host: xhci-rcar: Add Renesas RZ/G3E USB3 Host driver support
usb: host: xhci-plat: Add .post_resume_quirk for struct xhci_plat_priv
usb: host: xhci-rcar: Move R-Car reg definitions
dt-bindings: usb: Document Renesas RZ/G3E USB3HOST
usb: gadget: f_fs: Fix epfile null pointer access after ep enable.
...
-----BEGIN PGP SIGNATURE-----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=fwWe
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-gpio-input-pinctrl-pwm-v6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into gpio/for-next
Pull changes from the immutable branch between MFD, GPIO, Input, Pinctrl
and PWM trees containing the GPIO driver for max7360.
Add driver for Maxim Integrated MAX7360 GPIO/GPO controller.
Two sets of GPIOs are provided by the device:
- Up to 8 GPIOs, shared with the PWM and rotary encoder functionalities.
These GPIOs also provide interrupts on input changes.
- Up to 6 GPOs, on unused keypad columns pins.
Co-developed-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathieu Dubois-Briand <mathieu.dubois-briand@bootlin.com>
Link: https://lore.kernel.org/r/20250824-mdb-max7360-support-v14-7-435cfda2b1ea@bootlin.com
Signed-off-by: Lee Jones <lee@kernel.org>
This driver supports GPIO and IRQ functionality for NCT6694 MFD
device based on USB interface.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Ming Yu <a0282524688@gmail.com>
Link: https://lore.kernel.org/r/20250912091952.1169369-3-a0282524688@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add a a driver for the GPIO auxbus child device of the Intel USBIO USB
IO-expander used by the MIPI cameras on various new (Meteor Lake and
later) Intel laptops.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Co-developed-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Israel Cepeda <israel.a.cepeda.lopez@intel.com>
Link: https://lore.kernel.org/r/20250911181343.77398-3-hansg@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The traditional interfaces are only used on a small number of ancient
boards. Make these optional now so they can be disabled by default.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20250722153634.3683927-1-arnd@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This driver implements the GPIO service on top of the SMC framework
on Apple Mac machines. In particular, these are the GPIOs present in the
PMU IC which are used to control power to certain on-board devices.
Although the underlying hardware supports various pin config settings
(input/output, open drain, etc.), this driver does not implement that
functionality and leaves it up to the firmware to configure things
properly. We also don't yet support interrupts/events. This is
sufficient for device power control, which is the only thing we need to
support at this point. More features will be implemented when needed.
To our knowledge, only Apple Silicon Macs implement this SMC feature.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sven Peter <sven@kernel.org>
Signed-off-by: "Russell King (Oracle)" <rmk+kernel@armlinux.org.uk>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Sven Peter <sven@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20250610-smc-6-15-v7-6-556cafd771d3@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
* Split GPIO ACPI quirks to its own file
* Refactored GPIO ACPI library to shrink the code
The following is an automated git shortlog grouped by driver:
gpiolib:
- acpi: Update file references in the Documentation and MAINTAINERS
- acpi: Move quirks to a separate file
- acpi: Add acpi_gpio_need_run_edge_events_on_boot() getter
- acpi: Handle deferred list via new API
- acpi: Make sure we fill struct acpi_gpio_info
- acpi: Switch to use enum in acpi_gpio_in_ignore_list()
- acpi: Use temporary variable for struct acpi_gpio_info
- acpi: Deduplicate some code in __acpi_find_gpio()
- acpi: Reuse struct acpi_gpio_params in struct acpi_gpio_lookup
- acpi: Rename par to params for better readability
- acpi: Reduce memory footprint for struct acpi_gpio_params
- acpi: Remove index parameter from acpi_gpio_property_lookup()
- acpi: Improve struct acpi_gpio_info memory footprint
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEqaflIX74DDDzMJJtb7wzTHR8rCgFAmgtn20ACgkQb7wzTHR8
rChZig//SRA4VGnOF6nZfP985YZ9YjwdPibnxmkWBvyOodpJl3I1iiex1XrbX1MI
DxfQGDe8OhXWM6LL/569BCdSy5jHVpFGxISueIzz7gQ7WhzeWpC4/zO8wlW4InTy
xI/GScxqp65Rs0rLy+7OL3OEMSGJZbDLLZuadQnEAVfxRP5jCPDhBQyQBRdrQJyR
T+exFet5J6eMFvigpVcjCR3/Mlyp8Af/tgagtbL638/kOkfa2cgyMPTVO7Nmunrt
lLyAZVXytHN7DyhrIxh+H90U38oObix8rNOEXC2wdZMFjan75wOsq/+FxcrJPhzR
k2FsyVzM5ggcvWcR9gHXxwczSNu6g8wAzn20ibPfbdsVyNiKIyw+0mX8/JUN4mCS
Nc3xLxPM7cuve09Z6aAm8M1tPpOqrb0ATgv2kjV+yid7SLIEBgeJLru8Js+vjC0V
Cj+0jtlgUKiaNAo0g0Sp5JrARnJz95bNVTqVYqkcK5fqaFHR9OfI1Zd56Cgi1PBL
N2xqjlYHwm5QuKaXsq/5/81AmBjlHLkTLSlGo2w3ZRjHyFLVINRBGypZuKYFvZJ1
tZAgvK4r3GoBC6iJ+aXPy0ggr/oRbL0lIBTa/Za+rDij+rDhRCn1XwLcZ63tEry5
eJaTazj7lt1v1TXTgJRqqD2W0frSc5Ir7xipG5jcAjPnONPYo0s=
=WChc
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v6.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-next
intel-gpio for v6.16-1
* Split GPIO ACPI quirks to its own file
* Refactored GPIO ACPI library to shrink the code
The following is an automated git shortlog grouped by driver:
gpiolib:
- acpi: Update file references in the Documentation and MAINTAINERS
- acpi: Move quirks to a separate file
- acpi: Add acpi_gpio_need_run_edge_events_on_boot() getter
- acpi: Handle deferred list via new API
- acpi: Make sure we fill struct acpi_gpio_info
- acpi: Switch to use enum in acpi_gpio_in_ignore_list()
- acpi: Use temporary variable for struct acpi_gpio_info
- acpi: Deduplicate some code in __acpi_find_gpio()
- acpi: Reuse struct acpi_gpio_params in struct acpi_gpio_lookup
- acpi: Rename par to params for better readability
- acpi: Reduce memory footprint for struct acpi_gpio_params
- acpi: Remove index parameter from acpi_gpio_property_lookup()
- acpi: Improve struct acpi_gpio_info memory footprint
The gpiolib-acpi.c is huge enough even without DMI quirks.
Move them to a separate file for a better maintenance.
No functional change intended.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEdrbJNaO+IJqU8IdIUa+KL4f8d2EFAmgeEAYACgkQUa+KL4f8
d2EW6g//Q1uxdE113B4WgLZIN3z3BEAqQwsFRjbgXUcqHTRGbek42dh2PW9DLY7A
PGK1c63jA+pZPA4+UTTAUl+Hse3DV6ZFE9kpdxsLxAP2w83u3FwTUwOG+dJRRKTR
U0EN2FmionjwoZK7rpNGNpYgI1cVos4J8jnVRvc8ete3ZbET5kKZCM9z/LJ9phYG
daAbWZXo8Su7ws6awxWUL3NbOFx+jtX9H7U+UtVJUlEjCQ0vwa9mg7L0DC+WMh0B
n+eGp6RpNqdprIjoVAAh0/7D9jnMgXtj/vL13ofr+eesVA9O1P9lj9wNIOcZ+GIv
LVH/0Cl5dCDjLu0mhrZyuSHi96c1wMdQmBN2/5NGdqYvTo281tSxLWEI7zb26AF9
GhC5TA1OVPAA2zOF1az1bbAs+EmZqkIl9weV7w3Ad37uRLm5J6f6Pjx0gYABFvHW
8Ibny/SDCAe45R81LKG5ITSeJX1athXr5HhW4ShpL10pYQo8VK8tYkW1wtTpcYLc
lBjLmD0M/mdNFo/2Y/Dv24KQeZvpM4Z3IMjIE1kZLcITI14AECUnlp60zWuIU+lh
Z/U4ytrw3/0ac+gBUJ6bhdH8mxp/MHaw/I1mNKmm016sIfqTV5hhGC2i/kRoZki7
r4XlQViW6LqRXPW4WzVL4zgM0m+nM9jbd43K+pF2WUctthGkQ3I=
=2dKC
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-gpio-nvmem-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into gpio/for-next
Immutable branch between MFD, GPIO and NVMEM due for the v6.16 merge window
The Maxim MAX77759 is a companion PMIC for USB Type-C applications and
includes Battery Charger, Fuel Gauge, temperature sensors, USB Type-C
Port Controller (TCPC), NVMEM, and a GPIO expander.
This driver supports the GPIO functions using the platform device
registered by the core MFD driver.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250509-max77759-mfd-v10-2-962ac15ee3ef@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Implement GPIO functionality which capable of setting pin as
input, output. Also, each pin can be used as interrupt which
support rising, falling, or both edge type trigger.
Reviewed-by: Alex Elder <elder@riscstar.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Link: https://lore.kernel.org/r/20250412-03-k1-gpio-v8-2-1c6862d272ec@gentoo.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Blaize BLZP1600 GPIO controller is provided by VeriSilicon
Microelectronics based on the GPIO APB v0.2 design. It has 32
input/output ports which can be configured as edge or level
triggered interrupts. It also provides a de-bounce feature.
This controller is used on the Blaize BLZP1600 SoC.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nikolaos Pasaloukos <nikolaos.pasaloukos@blaize.com>
Link: https://lore.kernel.org/r/20250327-kernel-upstreaming-add_gpio_support-v2-2-bbe51f8d66da@blaize.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Both gpio-sim and gpio-virtuser share a mechanism to instantiate a
platform device, wait for probe completion, and retrieve the probe
success or error status synchronously. With gpio-aggregator planned to
adopt this approach for its configfs interface, it's time to factor
out the common code.
Add dev-sync-probe.[ch] to house helper functions used by all such
implementations.
No functional change.
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Link: https://lore.kernel.org/r/20250221133501.2203897-2-koichiro.den@canonical.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add a driver to support the Polarfire SoC gpio controller. Interrupt
controller support is unavailable for now and will be added at a later
date.
Signed-off-by: Lewis Hanly <lewis.hanly@microchip.com>
Co-developed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241104-tiny-evaluate-9336020b4b6a@spud
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
FTDI FT2232H is a USB to GPIO chip. Sealevel produces some devices
with this chip. FT2232H presents itself as a composite device with two
interfaces (each is an "MPSSE"). Each MPSSE has two banks (high and low)
of 8 GPIO each. I believe some MPSSE's have only one bank, but I don't
know how to identify them (I don't have any for testing) and as a result
are unsupported for the time being.
Additionally, this driver provides software polling-based interrupts for
edge detection. For the Sealevel device I have to test with, this works
well because there is hardware debouncing. From talking to Sealevel's
people, this is their preferred way to do edge detection.
Signed-off-by: Mary Strodl <mstrodl@csh.rit.edu>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241009131131.1618329-1-mstrodl@csh.rit.edu
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add gpio support for the Congatec Board Controller.
This Board Controller has 14 GPIO pins.
The driver is probed by the Congatec Board Controller MFD driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20241001-congatec-board-controller-v3-2-39ceceed5c47@bootlin.com
Signed-off-by: Lee Jones <lee@kernel.org>
The ADP5585 is a 10/11 input/output port expander with a built in keypad
matrix decoder, programmable logic, reset generator, and PWM generator.
This driver supports the GPIO function using the platform device
registered by the core MFD driver.
The driver is derived from an initial implementation from NXP, available
in commit 451f61b46b76 ("MLK-25917-2 gpio: adp5585-gpio: add
adp5585-gpio support") in their BSP kernel tree. It has been extensively
rewritten.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Co-developed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240722121100.2855-4-laurent.pinchart@ideasonboard.com
Signed-off-by: Lee Jones <lee@kernel.org>
The GPIO subsystem used to have a serious problem with undefined behavior
and use-after-free bugs on hot-unplug of GPIO chips. This can be
considered a corner-case by some as most GPIO controllers are enabled
early in the boot process and live until the system goes down but most
GPIO drivers do allow unbind over sysfs, many are loadable modules that
can be (force) unloaded and there are also GPIO devices that can be
dynamically detached, for instance CP2112 which is a USB GPIO expender.
Bugs can be triggered both from user-space as well as by in-kernel users.
We have the means of testing it from user-space via the character device
but the issues manifest themselves differently in the kernel.
This is a proposition of adding a new virtual driver - a configurable
GPIO consumer that can be configured over configfs (similarly to
gpio-sim) or described on the device-tree.
This driver is aimed as a helper in spotting any regressions in
hot-unplug handling in GPIOLIB.
Link: https://lore.kernel.org/r/20240708142912.120570-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This is a sloppy logic analyzer using GPIOs. It comes with a script to
isolate a CPU for polling. While this is definitely not a production
level analyzer, it can be a helpful first view when remote debugging.
Read the documentation for details.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240620094159.6785-2-wsa+renesas@sang-engineering.com
[Bartosz: moved the Kconfig entry into a different category]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This driver provides a basic GPIO driver for the Intel Granite Rapids-D
virtual GPIOs. On SoCs with limited physical pins on the package, the
physical pins controlled by this driver would be exposed on an external
device such as a BMC or CPLD. The virtual GPIO registers are an
interface to firmware, which communicates with the external device that
implements the GPIO hardware functionality.
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
No core changes this time around.
New drivers:
- New driver for Renesas R8A779H0 also known as R-Car V4M.
- New driver for the Awinic AW9523/B I2C GPIO expander.
I found this living out-of-tree in OpenWrt as an upstream
attempt had stalled on the finishing line, so I picked it
up and finished the job.
Improvements:
- The Nomadik pin control driver was for years re-used out of
tree for the ST STA chips, and now the IP was re-used in a
MIPS automotive SoC called MobilEyeq5, so it has been split
in pin control and GPIO drivers so the latter can be reused
by MobilEyeq5. (Along with a long list of cleanups.)
- A lot of overall cleanup and tidying up.
-----BEGIN PGP SIGNATURE-----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=Pt9Y
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"No core changes this time around.
New drivers:
- New driver for Renesas R8A779H0 also known as R-Car V4M.
- New driver for the Awinic AW9523/B I2C GPIO expander. I found this
living out-of-tree in OpenWrt as an upstream attempt had stalled on
the finishing line, so I picked it up and finished the job.
Improvements:
- The Nomadik pin control driver was for years re-used out of tree
for the ST STA chips, and now the IP was re-used in a MIPS
automotive SoC called MobilEyeq5, so it has been split in pin
control and GPIO drivers so the latter can be reused by MobilEyeq5.
(Along with a long list of cleanups)
- A lot of overall cleanup and tidying up"
* tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (87 commits)
drivers/gpio/nomadik: move dummy nmk_gpio_dbg_show_one() to header
gpio: nomadik: remove BUG_ON() in nmk_gpio_populate_chip()
dt-bindings: pinctrl: qcom: update compatible name for match with driver
pinctrl: aw9523: Make the driver tristate
pinctrl: nomadik: fix dereference of error pointer
gpio: nomadik: Back out some managed resources
pinctrl: aw9523: Add proper terminator
pinctrl: core: comment that pinctrl_add_gpio_range() is deprecated
pinctrl: pinmux: Suppress error message for -EPROBE_DEFER
pinctrl: Add driver for Awinic AW9523/B I2C GPIO Expander
dt-bindings: pinctrl: Add bindings for Awinic AW9523/AW9523B
gpio: nomadik: Finish conversion to use firmware node APIs
gpio: nomadik: fix Kconfig dependencies inbetween pinctrl & GPIO
pinctrl: da9062: Add OF table
dt-bindings: pinctrl: at91: add sam9x7
pinctrl: ocelot: remove redundant assignment to variable ret
gpio: nomadik: grab optional reset control and deassert it at probe
gpio: nomadik: support mobileye,eyeq5-gpio
gpio: nomadik: handle variadic GPIO count
gpio: nomadik: support shared GPIO IRQs
...
Previously, drivers/pinctrl/nomadik/pinctrl-nomadik.c registered two
platform drivers: pinctrl & GPIO. Move the GPIO aspect to the
drivers/gpio/ folder, as would be expected.
Both drivers are intertwined for a reason; pinctrl requires access to
GPIO registers for pinmuxing, pull-disable, disabling interrupts while
setting the muxing and wakeup control. Information sharing is done
through a shared array containing GPIO chips and a few helper
functions. That shared array is not touched from gpio-nomadik when
CONFIG_PINCTRL_NOMADIK is not defined.
Make no change to the code that moved into gpio-nomadik; there should be
no behavior change following. A few functions are shared and header
comments are added. Checkpatch warnings are addressed. NUM_BANKS is
renamed to NMK_MAX_BANKS.
It is supported to compile gpio-nomadik without pinctrl-nomadik. The
opposite is not true.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20240228-mbly-gpio-v2-6-3ba757474006@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ChromeOS embedded controller (EC) supports setting the state of
GPIOs when the system is unlocked, and getting the state of GPIOs in all
cases. The GPIOs are on the EC itself, so the EC acts similar to a GPIO
expander. Add a driver to get and set the GPIOs on the EC through the
host command interface.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add Nuvoton BMC NPCM7xx/NPCM8xx sgpio driver support.
Nuvoton NPCM SGPIO module is combine serial to parallel IC (HC595)
and parallel to serial IC (HC165), and use APB3 clock to control it.
This interface has 4 pins (D_out , D_in, S_CLK, LDSH).
BMC can use this driver to increase 64 GPI pins and 64 GPO pins to use.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The DS4520 is a 9-bit nonvolatile (NV) I/O expander.
It offers users a digitally programmable alternative
to hardware jumpers and mechanical switches that are
being used to control digital logic node.
Signed-off-by: Okan Sahin <okan.sahin@analog.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add support for the BlueField-3 SoC GPIO driver.
This driver configures and handles GPIO interrupts. It also enables a user
to manipulate certain GPIO pins via libgpiod tools or other kernel drivers.
The usables pins are defined via the "gpio-reserved-ranges" property.
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Now that GPIO aggregator supports a delay line, drop the duplicative
functionality, i.e. the entire gpio-delay driver.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add support for TPS65219 PMICs GPIO interface.
3 GPIO pins:
- GPIO0 only is IO but input mode reserved for MULTI_DEVICE_ENABLE usage.
- GPIO1 and GPIO2 are Output only and referred as GPO1 and GPO2 in spec.
GPIO0 is statically configured as input or output prior to Linux boot.
it is used for MULTI_DEVICE_ENABLE function.
This setting is statically configured by NVM.
GPIO0 can't be used as a generic GPIO (specification Table 8-34).
It's either a GPO when MULTI_DEVICE_EN=0 or a GPI when MULTI_DEVICE_EN=1.
Datasheet describes specific usage for non standard GPIO.
Datasheet: https://www.ti.com/lit/ds/symlink/tps65219.pdf
Co-developed-by: Jonathan Cormier <jcormier@criticallink.com>
Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
