Here is the char/misc/iio and other smaller driver subsystem updates for
7.1-rc1. Lots of stuff in here, all tiny, but relevant for the
different drivers they touch. Major points in here is:
- the usual large set of new IIO drivers and updates for that
subsystem (the large majority of this diffstat)
- lots of comedi driver updates and bugfixes
- coresight driver updates
- interconnect driver updates and additions
- mei driver updates
- binder (both rust and C versions) updates and fixes
- lots of other smaller driver subsystem updates and additions
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCaes/Ng8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymRBQCeOqRduhONI6LPIIvDDTaircoSib0AnRD8WwML
RxHo3/WjEd7FEUqwHA+H
=Heza
-----END PGP SIGNATURE-----
Merge tag 'char-misc-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc / IIO / and others driver updates from Greg KH:
"Here is the char/misc/iio and other smaller driver subsystem updates
for 7.1-rc1. Lots of stuff in here, all tiny, but relevant for the
different drivers they touch. Major points in here is:
- the usual large set of new IIO drivers and updates for that
subsystem (the large majority of this diffstat)
- lots of comedi driver updates and bugfixes
- coresight driver updates
- interconnect driver updates and additions
- mei driver updates
- binder (both rust and C versions) updates and fixes
- lots of other smaller driver subsystem updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-7.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (405 commits)
coresight: tpdm: fix invalid MMIO access issue
mei: me: add nova lake point H DID
mei: lb: add late binding version 2
mei: bus: add mei_cldev_uuid
w1: ds2490: drop redundant device reference
bus: mhi: host: pci_generic: Add Telit FE912C04 modem support
mei: csc: wake device while reading firmware status
mei: csc: support controller with separate PCI device
mei: convert PCI error to common errno
mei: trace: print return value of pci_cfg_read
mei: me: move trace into firmware status read
mei: fix idle print specifiers
mei: me: use PCI_DEVICE_DATA macro
sonypi: Convert ACPI driver to a platform one
misc: apds990x: fix all kernel-doc warnings
most: usb: Use kzalloc_objs for endpoint address array
hpet: Convert ACPI driver to a platform one
misc: vmw_vmci: Fix spelling mistakes in comments
parport: Remove completed item from to-do list
char: remove unnecessary module_init/exit functions
...
Everything:
Total patches: 368
Reviews/patch: 1.56
Reviewed rate: 74%
Excluding DAMON:
Total patches: 316
Reviews/patch: 1.77
Reviewed rate: 81%
Excluding DAMON and zram:
Total patches: 306
Reviews/patch: 1.81
Reviewed rate: 82%
Excluding DAMON, zram and maple_tree:
Total patches: 276
Reviews/patch: 2.01
Reviewed rate: 91%
Significant patch series in this merge:
- The 30 patch series "maple_tree: Replace big node with maple copy"
from Liam Howlett is mainly prepararatory work for ongoing development
but it does reduce stack usage and is an improvement.
- The 12 patch series "mm, swap: swap table phase III: remove swap_map"
from Kairui Song offers memory savings by removing the static swap_map.
It also yields some CPU savings and implements several cleanups.
- The 2 patch series "mm: memfd_luo: preserve file seals" from Pratyush
Yadav adds file seal preservation to LUO's memfd code.
- The 2 patch series "mm: zswap: add per-memcg stat for incompressible
pages" from Jiayuan Chen adds additional userspace stats reportng to
zswap.
- The 4 patch series "arch, mm: consolidate empty_zero_page" from Mike
Rapoport implements some cleanups for our handling of ZERO_PAGE() and
zero_pfn.
- The 2 patch series "mm/kmemleak: Improve scan_should_stop()
implementation" from Zhongqiu Han provides an robustness improvement and
some cleanups in the kmemleak code.
- The 4 patch series "Improve khugepaged scan logic" from Vernon Yang
"improves the khugepaged scan logic and reduces CPU consumption by
prioritizing scanning tasks that access memory frequently".
- The 2 patch series "Make KHO Stateless" from Jason Miu simplifies
Kexec Handover by "transitioning KHO from an xarray-based metadata
tracking system with serialization to a radix tree data structure that
can be passed directly to the next kernel"
- The 3 patch series "mm: vmscan: add PID and cgroup ID to vmscan
tracepoints" from Thomas Ballasi and Steven Rostedt enhances vmscan's
tracepointing.
- The 5 patch series "mm: arch/shstk: Common shadow stack mapping helper
and VM_NOHUGEPAGE" from Catalin Marinas is a cleanup for the shadow
stack code: remove per-arch code in favour of a generic implementation.
- The 2 patch series "Fix KASAN support for KHO restored vmalloc
regions" from Pasha Tatashin fixes a WARN() which can be emitted the KHO
restores a vmalloc area.
- The 4 patch series "mm: Remove stray references to pagevec" from Tal
Zussman provides several cleanups, mainly udpating references to "struct
pagevec", which became folio_batch three years ago.
- The 17 patch series "mm: Eliminate fake head pages from vmemmap
optimization" from Kiryl Shutsemau simplifies the HugeTLB vmemmap
optimization (HVO) by changing how tail pages encode their relationship
to the head page.
- The 2 patch series "mm/damon/core: improve DAMOS quota efficiency for
core layer filters" from SeongJae Park improves two problematic
behaviors of DAMOS that makes it less efficient when core layer filters
are used.
- The 3 patch series "mm/damon: strictly respect min_nr_regions" from
SeongJae Park improves DAMON usability by extending the treatment of the
min_nr_regions user-settable parameter.
- The 3 patch series "mm/page_alloc: pcp locking cleanup" from Vlastimil
Babka is a proper fix for a previously hotfixed SMP=n issue. Code
simplifications and cleanups ennsed.
- The 16 patch series "mm: cleanups around unmapping / zapping" from
David Hildenbrand implements "a bunch of cleanups around unmapping and
zapping. Mostly simplifications, code movements, documentation and
renaming of zapping functions".
- The 6 patch series "support batched checking of the young flag for
MGLRU" from Baolin Wang supports batched checking of the young flag for
MGLRU. It's part cleanups; one benchmark shows large performance
benefits for arm64.
- The 5 patch series "memcg: obj stock and slab stat caching cleanups"
from Johannes Weiner provides memcg cleanup and robustness improvements.
- The 5 patch series "Allow order zero pages in page reporting" from
Yuvraj Sakshith enhances page_reporting's free page reporting - it is
presently and undesirably order-0 pages when reporting free memory.
- The 6 patch series "mm: vma flag tweaks" from Lorenzo Stoakes is
cleanup work following from the recent conversion of the VMA flags to a
bitmap.
- The 10 patch series "mm/damon: add optional debugging-purpose sanity
checks" from SeongJae Park adds some more developer-facing debug checks
into DAMON core.
- The 2 patch series "mm/damon: test and document power-of-2
min_region_sz requirement" from SeongJae Park adds an additional DAMON
kunit test and makes some adjustments to the addr_unit parameter
handling.
- The 3 patch series "mm/damon/core: make passed_sample_intervals
comparisons overflow-safe" from SeongJae Park fixes a hard-to-hit time
overflow issue in DAMON core.
- The 7 patch series "mm/damon: improve/fixup/update ratio calculation,
test and documentation" from SeongJae Park is a "batch of misc/minor
improvements and fixups" for DAMON.
- The 4 patch series "mm: move vma_(kernel|mmu)_pagesize() out of
hugetlb.c" from David Hildenbrand fixes a possible issue with dax-device
when CONFIG_HUGETLB=n. Some code movement was required.
- The 6 patch series "zram: recompression cleanups and tweaks" from
Sergey Senozhatsky provides "a somewhat random mix of fixups,
recompression cleanups and improvements" in the zram code.
- The 11 patch series "mm/damon: support multiple goal-based quota
tuning algorithms" from SeongJae Park extend DAMOS quotas goal
auto-tuning to support multiple tuning algorithms that users can select.
- The 4 patch series "mm: thp: reduce unnecessary
start_stop_khugepaged()" from Breno Leitao fixes the khugpaged sysfs
handling so we no longer spam the logs with reams of junk when
starting/stopping khugepaged.
- The 3 patch series "mm: improve map count checks" from Lorenzo Stoakes
provides some cleanups and slight fixes in the mremap, mmap and vma
code.
- The 5 patch series "mm/damon: support addr_unit on default monitoring
targets for modules" from SeongJae Park extends the use of DAMON core's
addr_unit tunable.
- The 5 patch series "mm: khugepaged cleanups and mTHP prerequisites"
from Nico Pache provides cleanups in the khugepaged and is a base for
Nico's planned khugepaged mTHP support.
- The 15 patch series "mm: memory hot(un)plug and SPARSEMEM cleanups"
from David Hildenbrand implements code movement and cleanups in the
memhotplug and sparsemem code.
- The 2 patch series "mm: remove CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE and
cleanup CONFIG_MIGRATION" from David Hildenbrand rationalizes some
memhotplug Kconfig support.
- The 6 patch series "change young flag check functions to return bool"
from Baolin Wang is "a cleanup patchset to change all young flag check
functions to return bool".
- The 3 patch series "mm/damon/sysfs: fix memory leak and NULL
dereference issues" from Josh Law and SeongJae Park fixes a few
potential DAMON bugs.
- The 25 patch series "mm/vma: convert vm_flags_t to vma_flags_t in vma
code" from "converts a lot of the existing use of the legacy vm_flags_t
data type to the new vma_flags_t type which replaces it". Mainly in the
vma code.
- The 21 patch series "mm: expand mmap_prepare functionality and usage"
from Lorenzo Stoakes "expands the mmap_prepare functionality, which is
intended to replace the deprecated f_op->mmap hook which has been the
source of bugs and security issues for some time". Cleanups,
documentation, extension of mmap_prepare into filesystem drivers.
- The 13 patch series "mm/huge_memory: refactor zap_huge_pmd()" from
Lorenzo Stoakes simplifies and cleans up zap_huge_pmd(). Additional
cleanups around vm_normal_folio_pmd() and the softleaf functionality are
performed.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCad3HDQAKCRDdBJ7gKXxA
jrUQAPwNhPk5nPSxnyxjAeQtOBHqgCdnICeEismLajPKd9aYRgEA0s2XAu3tSUYi
GrBnWImHG3s4ePQxVcPCegWTsOUrXgQ=
=1Q7o
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2026-04-13-21-45' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- "maple_tree: Replace big node with maple copy" (Liam Howlett)
Mainly prepararatory work for ongoing development but it does reduce
stack usage and is an improvement.
- "mm, swap: swap table phase III: remove swap_map" (Kairui Song)
Offers memory savings by removing the static swap_map. It also yields
some CPU savings and implements several cleanups.
- "mm: memfd_luo: preserve file seals" (Pratyush Yadav)
File seal preservation to LUO's memfd code
- "mm: zswap: add per-memcg stat for incompressible pages" (Jiayuan
Chen)
Additional userspace stats reportng to zswap
- "arch, mm: consolidate empty_zero_page" (Mike Rapoport)
Some cleanups for our handling of ZERO_PAGE() and zero_pfn
- "mm/kmemleak: Improve scan_should_stop() implementation" (Zhongqiu
Han)
A robustness improvement and some cleanups in the kmemleak code
- "Improve khugepaged scan logic" (Vernon Yang)
Improve khugepaged scan logic and reduce CPU consumption by
prioritizing scanning tasks that access memory frequently
- "Make KHO Stateless" (Jason Miu)
Simplify Kexec Handover by transitioning KHO from an xarray-based
metadata tracking system with serialization to a radix tree data
structure that can be passed directly to the next kernel
- "mm: vmscan: add PID and cgroup ID to vmscan tracepoints" (Thomas
Ballasi and Steven Rostedt)
Enhance vmscan's tracepointing
- "mm: arch/shstk: Common shadow stack mapping helper and
VM_NOHUGEPAGE" (Catalin Marinas)
Cleanup for the shadow stack code: remove per-arch code in favour of
a generic implementation
- "Fix KASAN support for KHO restored vmalloc regions" (Pasha Tatashin)
Fix a WARN() which can be emitted the KHO restores a vmalloc area
- "mm: Remove stray references to pagevec" (Tal Zussman)
Several cleanups, mainly udpating references to "struct pagevec",
which became folio_batch three years ago
- "mm: Eliminate fake head pages from vmemmap optimization" (Kiryl
Shutsemau)
Simplify the HugeTLB vmemmap optimization (HVO) by changing how tail
pages encode their relationship to the head page
- "mm/damon/core: improve DAMOS quota efficiency for core layer
filters" (SeongJae Park)
Improve two problematic behaviors of DAMOS that makes it less
efficient when core layer filters are used
- "mm/damon: strictly respect min_nr_regions" (SeongJae Park)
Improve DAMON usability by extending the treatment of the
min_nr_regions user-settable parameter
- "mm/page_alloc: pcp locking cleanup" (Vlastimil Babka)
The proper fix for a previously hotfixed SMP=n issue. Code
simplifications and cleanups ensued
- "mm: cleanups around unmapping / zapping" (David Hildenbrand)
A bunch of cleanups around unmapping and zapping. Mostly
simplifications, code movements, documentation and renaming of
zapping functions
- "support batched checking of the young flag for MGLRU" (Baolin Wang)
Batched checking of the young flag for MGLRU. It's part cleanups; one
benchmark shows large performance benefits for arm64
- "memcg: obj stock and slab stat caching cleanups" (Johannes Weiner)
memcg cleanup and robustness improvements
- "Allow order zero pages in page reporting" (Yuvraj Sakshith)
Enhance free page reporting - it is presently and undesirably order-0
pages when reporting free memory.
- "mm: vma flag tweaks" (Lorenzo Stoakes)
Cleanup work following from the recent conversion of the VMA flags to
a bitmap
- "mm/damon: add optional debugging-purpose sanity checks" (SeongJae
Park)
Add some more developer-facing debug checks into DAMON core
- "mm/damon: test and document power-of-2 min_region_sz requirement"
(SeongJae Park)
An additional DAMON kunit test and makes some adjustments to the
addr_unit parameter handling
- "mm/damon/core: make passed_sample_intervals comparisons
overflow-safe" (SeongJae Park)
Fix a hard-to-hit time overflow issue in DAMON core
- "mm/damon: improve/fixup/update ratio calculation, test and
documentation" (SeongJae Park)
A batch of misc/minor improvements and fixups for DAMON
- "mm: move vma_(kernel|mmu)_pagesize() out of hugetlb.c" (David
Hildenbrand)
Fix a possible issue with dax-device when CONFIG_HUGETLB=n. Some code
movement was required.
- "zram: recompression cleanups and tweaks" (Sergey Senozhatsky)
A somewhat random mix of fixups, recompression cleanups and
improvements in the zram code
- "mm/damon: support multiple goal-based quota tuning algorithms"
(SeongJae Park)
Extend DAMOS quotas goal auto-tuning to support multiple tuning
algorithms that users can select
- "mm: thp: reduce unnecessary start_stop_khugepaged()" (Breno Leitao)
Fix the khugpaged sysfs handling so we no longer spam the logs with
reams of junk when starting/stopping khugepaged
- "mm: improve map count checks" (Lorenzo Stoakes)
Provide some cleanups and slight fixes in the mremap, mmap and vma
code
- "mm/damon: support addr_unit on default monitoring targets for
modules" (SeongJae Park)
Extend the use of DAMON core's addr_unit tunable
- "mm: khugepaged cleanups and mTHP prerequisites" (Nico Pache)
Cleanups to khugepaged and is a base for Nico's planned khugepaged
mTHP support
- "mm: memory hot(un)plug and SPARSEMEM cleanups" (David Hildenbrand)
Code movement and cleanups in the memhotplug and sparsemem code
- "mm: remove CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE and cleanup
CONFIG_MIGRATION" (David Hildenbrand)
Rationalize some memhotplug Kconfig support
- "change young flag check functions to return bool" (Baolin Wang)
Cleanups to change all young flag check functions to return bool
- "mm/damon/sysfs: fix memory leak and NULL dereference issues" (Josh
Law and SeongJae Park)
Fix a few potential DAMON bugs
- "mm/vma: convert vm_flags_t to vma_flags_t in vma code" (Lorenzo
Stoakes)
Convert a lot of the existing use of the legacy vm_flags_t data type
to the new vma_flags_t type which replaces it. Mainly in the vma
code.
- "mm: expand mmap_prepare functionality and usage" (Lorenzo Stoakes)
Expand the mmap_prepare functionality, which is intended to replace
the deprecated f_op->mmap hook which has been the source of bugs and
security issues for some time. Cleanups, documentation, extension of
mmap_prepare into filesystem drivers
- "mm/huge_memory: refactor zap_huge_pmd()" (Lorenzo Stoakes)
Simplify and clean up zap_huge_pmd(). Additional cleanups around
vm_normal_folio_pmd() and the softleaf functionality are performed.
* tag 'mm-stable-2026-04-13-21-45' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (369 commits)
mm: fix deferred split queue races during migration
mm/khugepaged: fix issue with tracking lock
mm/huge_memory: add and use has_deposited_pgtable()
mm/huge_memory: add and use normal_or_softleaf_folio_pmd()
mm: add softleaf_is_valid_pmd_entry(), pmd_to_softleaf_folio()
mm/huge_memory: separate out the folio part of zap_huge_pmd()
mm/huge_memory: use mm instead of tlb->mm
mm/huge_memory: remove unnecessary sanity checks
mm/huge_memory: deduplicate zap deposited table call
mm/huge_memory: remove unnecessary VM_BUG_ON_PAGE()
mm/huge_memory: add a common exit path to zap_huge_pmd()
mm/huge_memory: handle buggy PMD entry in zap_huge_pmd()
mm/huge_memory: have zap_huge_pmd return a boolean, add kdoc
mm/huge: avoid big else branch in zap_huge_pmd()
mm/huge_memory: simplify vma_is_specal_huge()
mm: on remap assert that input range within the proposed VMA
mm: add mmap_action_map_kernel_pages[_full]()
uio: replace deprecated mmap hook with mmap_prepare in uio_info
drivers: hv: vmbus: replace deprecated mmap hook with mmap_prepare
mm: allow handling of stacked mmap_prepare hooks in more drivers
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmnS4Y8eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGe6AIAI4rjLLPlxUKQbx4
JP9lsKH7vqeIVvuMqzFau7+B8ngJ+80OESnBF7n43oNEqdJ0NYiL+rPtcGgBjZDP
yUu5DlzVSxpAIQBZe2Nc0dz/5NbT9QxKyC5Yl/whpNIR7UHx1RFvDJYxwN9xKxTw
ggLQevKAnHrKjIOKjq70Yqz2T1JMXc9Wp/xpur0oGioiFW/lH24CgHDXjE2Ka9oD
wqhotzThuSaaVDmqZ8WNFKxx2onR4r8/NpljaVT2mWRJ2+IMF4pMOBJZRQiNZtRa
1CsoJ3aV6pslAsuC1dLboCMul48VUgyu7l3xQwXVuA5bRO1jqt5ILWC10g09OItU
7CxGTno=
=1TRg
-----END PGP SIGNATURE-----
Merge tag 'v7.0-rc7' into char-misc-next
We need the char/misc/iio/comedi fixes in here as well for testing
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
zap_vma_ptes() is the only zapping function we export to modules.
It's essentially a wrapper around zap_vma_range(), however, with some
safety checks:
* That the passed range fits fully into the VMA
* That it's only used for VM_PFNMAP
We will add support for VM_MIXEDMAP next, so use the more-generic term
"special vma", although "special" is a bit overloaded. Maybe we'll later
just support any VM_SPECIAL flag.
While at it, improve the kerneldoc.
Link: https://lkml.kernel.org/r/20260227200848.114019-16-david@kernel.org
Signed-off-by: David Hildenbrand (Arm) <david@kernel.org>
Acked-by: Leon Romanovsky <leon@kernel.org> [drivers/infiniband]
Reviewed-by: Lorenzo Stoakes (Oracle) <ljs@kernel.org>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Alice Ryhl <aliceryhl@google.com>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Arve <arve@android.com>
Cc: "Borislav Petkov (AMD)" <bp@alien8.de>
Cc: Carlos Llamas <cmllamas@google.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Claudio Imbrenda <imbrenda@linux.ibm.com>
Cc: Daniel Borkman <daniel@iogearbox.net>
Cc: Dave Airlie <airlied@gmail.com>
Cc: David Ahern <dsahern@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jakub Kacinski <kuba@kernel.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Jann Horn <jannh@google.com>
Cc: Janosch Frank <frankja@linux.ibm.com>
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Miguel Ojeda <ojeda@kernel.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Namhyung kim <namhyung@kernel.org>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Pedro Falcato <pfalcato@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Shakeel Butt <shakeel.butt@linux.dev>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Todd Kjos <tkjos@android.com>
Cc: Tvrtko Ursulin <tursulin@ursulin.net>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Use the common USB helper for looking up bulk and interrupt endpoints
instead of open coding.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260330094646.1623523-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switched struct pointer member to a flexible array member to get rid of
kzalloc_objs as there's no need for them to be separately allocated.
AAdded __counted_by for extra runtime analysis.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20260311232459.18407-1-rosenp@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many Comedi drivers have unnecessary empty module_init and module_exit
functions. Remove them. Note that if a module_init function exists, a
module_exit function must also exist; otherwise, the module cannot be
unloaded.
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Reviewed-by: Ian Abbott <abboti@mev.co.uk>
Link: https://patch.msgid.link/20260131013810.32265-1-enelsonmoore@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6cd5a9a35c ("staging/trivial: fix typos concerning "access"")
accidentally changed "Acces I/O Products" to "Access I/O Products",
although "Acces" should actually be a capitalized acronym "ACCES"
(standing for "Acquisition, Control, and Communication: Engineering &
Systems"). Change it in the "aio_aio12_8" and "aio_iiro_16" drivers and
change the Kconfig file to match.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260129114402.11033-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "s526" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a Sensoray
526 board. It currently allows any base address to be configured but
the hardware only supports base addresses (configured by on-board DIP
switches) in the range 0 to 0xFFC0 on 64-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-47-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "rti800" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a RTI-802
board. It currently allows any base address to be configured but the
hardware only supports base addresses (configured by on-board DIP
switches) in the range 0 to 0x3FC on 4-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-46-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "rti800" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a RTI-800
or RTI-815 board. It currently allows any base address to be configured
but the hardware only supports base addresses (configured by on-board
DIP switches) in the range 0 to 0x3F0 on 16-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-45-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "pcmmio" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a
PCM-UIO48A or PCM-UIO96A board. It will probably work with the later
PCM-UIO48C and PCM-UIO96C boards. It currently allows any base address
to be configured but the hardware only supports base addresses
(configured by on-board jumpers) in the range 0 to 0xFFF0 on 16-byte
boundaries (for PCM-UIO48C) or 0 to 0xFFE0 on 32-byte boundaries (for
PCM-UIO96C). (The PCM-UIO48A supports base addresses up to 0xFF0 and
the PCI-UIO96A supports base addresses up to 0x7E0.)
Add a sanity check to ensure the device is not configured at an
unsupported base address (allowing for the extended range of the "C"
models).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-44-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "pcmmio" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a PCM-MIO
board. It currently allows any base address to be configured but the
hardware only supports base addresses (configured by on-board jumpers)
in the range 0 to 0xFFE0 on 32-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-43-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "pcmda12" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a
PCM-D/A-12 or PCM-A/D-16 board. It currently allows any base address to
be configured. I cannot find a full manual, but the short datasheet
says it uses 15 consecutive I/O addresses on "any even sixteen port
boundary", so assume it supports base addresses (configured by on-board
jumpers) in the range 0 to 0x3E0 on 32-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-42-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "pcmad" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a
PCM-A/D-12 or PCM-A/D-16 board. It currently allows any base address to
be configured but the hardware only supports base addresses (configured
by on-board jumpers) in the range 0 to 0x3FC on 4-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-41-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "pcm3724" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a PCM-3724
board. It currently allows any base address to be configured but the
hardware only supports base addresses (configured by on-board DIP
switches) in the range 0 to 0x3F0 on 16-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-40-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "pcl818" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a board in
the PCL-818 series. It currently allows any base address to be
configured but the hardware devices only support base addresses
(configured by on-board DIP switches) from 0 to 0x3F0 on 16-byte
boundaries. If the board has a FIFO and jumper JP6 is in the "Enabled"
(default) position, then the base address needs to be on a 32-byte
boundary and the length of the I/O port region will be 32 (to allow
access to the FIFO registers) instead of 16. The state of jumper JP6 is
unknown, so if the board has a FIFO device and is being configured on an
odd 16-byte boundary, assume that jumper JP6 is in the "Disabled"
position (to disallow access to the FIFO registers).
Add a sanity check to ensure the device is not configured at an
unsupported base address.
If the board has a FIFO and is configured on an odd 16-byte boundary,
log a reminder that JP6 needs to be in the "Disabled" position for
correct operation. If the board has a FIFO and is configured on an even
16-byte boundary and the configuration option has been set to use the
FIFO (`it->options[2] == -1`), log a reminder that JP6 needs to be in
the "Enabled" position.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-39-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "pcl816" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a PCL-816
or PCL-814B ISA board. It currently allows any base address to be
configured but the hardware devices only support base addresses
(configured by on-board DIP switches) from 0 to 0x3F0 on 16-byte
boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-38-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "pcl812" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of various
analog/digital I/O ISA boards from Advantech, ADLINK, and ICP DAS. It
currently allows any base address to be configured but the hardware
devices only support base addresses (configured by on-board DIP
switches) from 0 or 0x200 (depending on the model) to 0x3F0 on 16-byte
boundaries.
Store the minimum supported I/O base addresses in the static board
information array elements and add a sanity check to ensure the device
is not configured at an unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-37-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "pcl730" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of various
relay output and digital input ISA board from Advantech, ADLINK, ICP
DAS, and Diamond Systems. It currently allows any base address to be
configured but the hardware devices have restrictions on the base
addresses (configured by on-board DIP switches or jumpers), including
the alignment, which can be larger than the board's I/O register address
span. The Diamond Systems IR104-PBF board is particularly restricted to
4 different base addresses with different sized gaps between the
possible addresses.
Store the minimum supported I/O base addresses and alignment in the
static board information array elements and add a sanity check to ensure
the device is not configured at an unsupported base address. For the
IR104-PBF board, add a special check that the base address is one of the
4 supported base addresses for that board.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-36-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "pcl726" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of various
analog output ISA boards from Advantech (PCL-726/727/728) and ADLINK
(ACL-6126/6128). (Most of them also have digital I/O.) It currently
allows any base address to be configured but the hardware only supports
base addresses (configured by on-board DIP switches) from 0 or 0x200 up
to nearly 0x3FF, depending on the model.
Store the minimum and maximum supported I/O address ranges in the static
board information array elements (the required alignment is already
stored in the `io_len` member), and add a sanity check to ensure the
device is not configured at an unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-35-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "pcl724" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of various
8255 chip-based digital I/O ISA boards from Advantech, ADLINK,
WinSystems, and Diamond Systems. It currently allows any base address
to be configured but the hardware only supports base addresses
(configured by on-board DIP switches or jumpers) in various ranges, and
on various alignment boundaries, depending on the model.
Store the minimum and maximum supported I/O address ranges in the static
board information array elements (the required alignment is already
stored in the `io_range` member), and add a sanity check to ensure the
device is not configured at an unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-34-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "pcl711" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of an
Advantech PCL-711 series board or an Adlink ACL-8112 series board. It
currently allows any base address to be configured but the hardware only
supports base addresses (configured by on-board DIP switches) in the
range 0 to 0x3F0 (for PCL-711) or 0x200 to 0x3F0 (for ACL-8112) on
16-byte boundaries.
Store the minimum supported I/O base address in the static board
information array elements, and add a sanity check to ensure the device
is not configured at an unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-33-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "ni_labpc" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a
Lab-PC-1200 series or Lab-PC+ board. It currently allows any base
address to be configured but the hardware only supports base addresses
(configured by a configuration utility and stored in nonvolatile memory)
in the range 0 to 0x3E0 on 32-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-32-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "ni_atmio16d" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of an
AT-MIO-16 o AT-MIO-16D board. It currently allows any base address to
be configured but the hardware only supports base addresses (configured
by on-board DIP switches) in the range 0 to 0x3E0 on 32-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-31-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "ni_atmio" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of an AT E
Series board. Or, if the option value is zero, it can search ISA PNP
devices to look for a compatible board. If the base address is
configured manually, it currently allows any base address to be
configured but the hardware only supports base addresses (configured by
a configuration utility and stored in nonvolatile memory) in the range
0x20 to 0xFFE0 on 32-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-30-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "ni_at_ao" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of an AT-AO-6
or AT-AO-10 board. It currently allows any base address to be
configured but the hardware only supports base addresses (configured by
on-board jumpers) in the range 0 to 0x3E0 on 32-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-29-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "ni_at_a2150" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of an AT-A2150
series board. It currently allows any base address to be configured but
the hardware only supports base addresses (configured by on-board
jumpers) in the range 0 to 0x3E0 on 32-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-28-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "multiq3" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a Multiq-3
board. It currently allows any base address to be configured but the
hardware only supports base addresses (configured by on-board jumpers)
in the range 0 to 0x3F0 on 16-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-27-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "mpc624" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a MPC624
board. It currently allows any base address to be configured but the
hardware only supports base addresses (configured by on-board jumpers)
in the range 0 to 0x3F0 on 16-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-26-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "fl512" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of an FL512
board. It currently allows any base address to be configured and uses a
16-byte register region.
I cannot find any information about this board, but assume it needs to
be aligned to a 16-byte boundary. I have no idea about the allowed
range, so allow anything in a 32-bit range and add a "FIXME" comment
(although most ancient ISA cards only support 10-bit address decoding).
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-25-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "dt2817" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a DT2817
board. It currently allows any base address to be configured but the
hardware only supports base addresses (configured by on-board jumpers)
in the range 0x200 to 0x3f8 on 8-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-24-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "dt2815" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a DT2815
board. It currently allows any base address to be configured but the
hardware only supports base addresses (configured by an on-board DIP
switch) in the range 0x200 to 0x3fe on 2-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-23-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "dt2814" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a DT2814
board. It currently allows any base address to be configured but the
hardware only supports base addresses (configured by an on-board DIP
switch) in the range 0x200 to 0x3fe on 2-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-22-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "dt2811" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a supported
board in the DT2811 family. It currently allows any base address to be
configured but the hardware only supports base addresses (configured by
on-board jumpers) in the range 0x200 to 0x3f8 on 8-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-21-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "dt2801" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a supported
board in the DT2801 family. It currently allows any base address to be
configured but the hardware only supports base addresses (configured by
an on-board DIP switch) in the range 0x200 to 0x3fe on 2-byte
boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-20-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "dmm32at" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a
Diamond-MM-32-AT board. It currently allows any base address to be
configured but the hardware only supports 8 possible base addresses
(selected by 3 on-board jumpers). These are 0x100, 0x140, 0x180, 0x200,
0x280, 0x300, 0x340, and 0x380.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-19-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "das800" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a supported
board in the DAS800 family. It currently allows any base address to be
configured but the hardware only supports base addresses (configured by
an on-board DIP switch) in the range 0 to 0x3f8 on 8-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-18-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "das6402" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a supported
board in the DAS6402 family. It currently allows any base address to be
configured but the hardware only supports base addresses (configured by
an on-board DIP switch) in the range 0 to 0x3f0 on 16-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-17-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "das1800" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a board
compatible with the DAS1800 series. It currently allows any base
address to be configured but the hardware only supports base addresses
(configured by an on-board DIP switch) in the range 0 to 0x3f0 on
16-byte boundaries. Some boards have an additional span of up to 0x10
registers at offset 0x400 from the main 0x10 byte region.
Add a sanity check to ensure the device is not configured at an
unsupported base address. If the main base address is correctly aligned
and within range, then the additional region at offset 0x400 from the
configured base address will naturally be within range and correctly
aligned.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-16-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "das16m1" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a DAS16/M1
board. It currently allows any base address to be configured but the
hardware only supports base addresses (configured by an on-board DIP
switch) in the range 0 to 0x3f0 on 16-byte boundaries. It has an
additional span of 0x8 registers at offset 0x400 from the main 0x10 byte
region.
Add a sanity check to ensure the device is not configured at an
unsupported base address. If the main base address is correctly aligned
and within range, then the additional region at offset 0x400 from the
configured base address will naturally be within range and correctly
aligned.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-15-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "das16" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a various
DAS16 compatible boards. It currently allows any base address to be
configured but the hardware only supports base addresses (configured by
an on-board DIP switch) in the range 0 to 0x3f0 on 16- or 32-byte
boundaries. Some of the boards have an 8255 chip at offset 0x10 and
require the board to be configured on a 32-byte boundary unless some
on-board jumpers are set to limit the board to decoding only the first
0x10 registers, disabling access to the 8255. Some other boards place
the 8255 chip (and some other registers) at offset 0x400 from the base
address, decoding 0x10 registers at the base address and 0x8 registers
at the base address plus 0x400.
Add a sanity check to ensure the device is not configured at an
unsupported base address. If the device has the 8255 chip at offset
0x10, and is being configured with the base address at an odd 16-byte
boundary, limit the size of the region to 0x10 and disable the 8255
subdevice.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-14-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "das08_isa" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a supported
board in the DAS08 family. It currently allows any base address to be
configured but the hardware only supports base addresses (configured by
an on-board DIP switch) in the range 0 to 0x3f0 on 16-byte boundaries.
(Technically, the DIP switches allow 8-byte boundaries, but I do not
think that is advisable given that the boards decode an 16-byte address
range.)
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-13-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "dac02" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a supported
DAC-02 board. It currently allows any base address to be configured but
the hardware only supports base addresses (configured by an on-board DIP
switch) in the range 0x200 to 0x3f8 on 8-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-12-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "comedi_parport" driver treats a standard printer parallel port as a
COMEDI digital I/O device, driving the port's I/O registers directly.
It uses an admin-supplied configuration option (`it->options[0]`) to
configure the I/O port base address of the device. Currently, the
driver allows any I/O base address to be specified as long as the I/O
region can be reserved, and it converts the specified `int` option value
holding the base address to `unsigned long`.
It doesn't make sense to allow base addresses that are not aligned to
4-byte boundaries (for SPP printer ports, although printer ports with
EPP/ECP support actually need to be aligned on 8-byte boundaries), so
add a check for 4-byte alignment.
Convert the option value that specifies the base address from `int` to
`unsigned int` instead of `unsigned long` so it ends up the same on
32-bit and 64-bit systems.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-11-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "c6xdigio" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a supported
C6x_DIGIO DSP device connected to a PC printer parallel port (driving
the port's I/O registers directly). Currently, the driver allows any
I/O base address to be specified as long as the I/O region can be
reserved, and it converts the specified `int` option value holding the
base address to `unsigned long`.
It doesn't make sense to allow base addresses that are not aligned to
4-byte boundaries (for SPP printer ports, although printer ports with
EPP/ECP support actually need to be aligned on 8-byte boundaries), so
add a check for 4-byte alignment.
Convert the option value that specifies the base address from `int` to
`unsigned int` instead of `unsigned long` so it ends up the same on
32-bit and 64-bit systems.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-10-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "amplc_pc263" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a supported
PC263 board. It currently allows any base address to be configured but
the hardware only supports base addresses (set by on-board DIP switches)
in the range 0 to 0x7FE on 2-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-9-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "amplc_pc236" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a supported
PC36AT board. It currently allows any base address to be configured but
the hardware only supports base addresses (set by on-board DIP switches)
in the range 0 to 0xFFC on 4-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-8-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "amplc_dio200" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a supported
board (PC212E, PC214E, PC215E, PC218E, or PC272E). It currently allows
any base address to be configured but the hardware only supports base
addresses (set by on-board DIP switches) in the range 0 to 0xFE0 on
32-byte boundaries. (Technically, the DIP switches allow 16-byte
boundaries, but I do not think that is advisable given that the boards
decode a 32-byte address range.)
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-7-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "aio_iiro_16" driver uses an admin-supplied configuration option
(`it->options[0]`) to configure the I/O port base address of a supported
board (IIRO-16). It currently allows any base address to be configured
but the hardware only supports base addresses (set by on-board jumpers)
in the range 0x100 to 0x3F8 on 8-byte boundaries.
Add a sanity check to ensure the device is not configured at an
unsupported base address.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://patch.msgid.link/20260130170416.49994-6-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
