btintel_pcie_get_mac_access() and btintel_pcie_release_mac_access()
were programming STOP_MAC_ACCESS_DIS and XTAL_CLK_REQ in addition to
the MAC_ACCESS_REQ handshake. These bits are not part of the host
MAC-access handshake on the supported parts; the driver was
programming them incorrectly. Drop the writes so the register update
contains only the bits the controller actually consumes.
Fixes: b9465e6670 ("Bluetooth: btintel_pcie: Read hardware exception data")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CSR boot stage register bit 12 is documented as a device warning,
not a fatal error. Rename the bit definition accordingly and stop
including it in btintel_pcie_in_error().
This keeps warning-only boot stage values from being classified as
errors while preserving abort-handler state as the actual error
condition.
Fixes: 190377500f ("Bluetooth: btintel_pcie: Dump debug registers on error")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use strscpy() instead of snprintf() to copy plain strings with no format
specifiers.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Align each descriptor/index/context region to 128 bytes before
calculating the total DMA pool size. This ensures the memory layout
shared with firmware meets the 128-byte alignment requirement.
The DMA pool alignment is also set to 128 bytes to match the firmware
expectation for all shared structures.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add device coredump support for Scorpious Peak2F product.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add support for Intel Bluetooth Scorpious Peak2F core.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add device coredump support for Scorpious Peak2 product.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add support for Intel Bluetooth Scorpious Peak2 core.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use struct_size(), which provides additional compile-time checks for
structures with flexible array members (e.g., __must_be_array()), to
determine the allocation size for a new 'struct hci_drv_rp_read_info'.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Replace snprintf("%s", ...) with the faster and more direct strscpy().
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
Core & protocols
----------------
- A significant effort all around the stack to guide the compiler to
make the right choice when inlining code, to avoid unneeded calls for
small helper and stack canary overhead in the fast-path. This
generates better and faster code with very small or no text size
increases, as in many cases the call generated more code than the
actual inlined helper.
- Extend AccECN implementation so that is now functionally complete,
also allow the user-space enabling it on a per network namespace
basis.
- Add support for memory providers with large (above 4K) rx buffer.
Paired with hw-gro, larger rx buffer sizes reduce the number of
buffers traversing the stack, dincreasing single stream CPU usage by
up to ~30%.
- Do not add HBH header to Big TCP GSO packets. This simplifies the RX
path, the TX path and the NIC drivers, and is possible because
user-space taps can now interpret correctly such packets without the
HBH hint.
- Allow IPv6 routes to be configured with a gateway address that is
resolved out of a different interface than the one specified, aligning
IPv6 to IPv4 behavior.
- Multi-queue aware sch_cake. This makes it possible to scale the rate
shaper of sch_cake across multiple CPUs, while still enforcing a
single global rate on the interface.
- Add support for the nbcon (new buffer console) infrastructure to
netconsole, enabling lock-free, priority-based console operations that
are safer in crash scenarios.
- Improve the TCP ipv6 output path to cache the flow information, saving
cpu cycles, reducing cache line misses and stack use.
- Improve netfilter packet tracker to resolve clashes for most protocols,
avoiding unneeded drops on rare occasions.
- Add IP6IP6 tunneling acceleration to the flowtable infrastructure.
- Reduce tcp socket size by one cache line.
- Notify neighbour changes atomically, avoiding inconsistencies between
the notification sequence and the actual states sequence.
- Add vsock namespace support, allowing complete isolation of vsocks
across different network namespaces.
- Improve xsk generic performances with cache-alignment-oriented
optimizations.
- Support netconsole automatic target recovery, allowing netconsole
to reestablish targets when underlying low-level interface comes back
online.
Driver API
----------
- Support for switching the working mode (automatic vs manual) of a DPLL
device via netlink.
- Introduce PHY ports representation to expose multiple front-facing
media ports over a single MAC.
- Introduce "rx-polarity" and "tx-polarity" device tree properties, to
generalize polarity inversion requirements for differential signaling.
- Add helper to create, prepare and enable managed clocks.
Device drivers
--------------
- Add Huawei hinic3 PF etherner driver.
- Add DWMAC glue driver for Motorcomm YT6801 PCIe ethernet controller.
- Add ethernet driver for MaxLinear MxL862xx switches
- Remove parallel-port Ethernet driver.
- Convert existing driver timestamp configuration reporting to
hwtstamp_get and remove legacy ioctl().
- Convert existing drivers to .get_rx_ring_count(), simplifing the RX
ring count retrieval. Also remove the legacy fallback path.
- Ethernet high-speed NICs:
- Broadcom (bnxt, bng):
- bnxt: add FW interface update to support FEC stats histogram and
NVRAM defragmentation
- bng: add TSO and H/W GRO support
- nVidia/Mellanox (mlx5):
- improve latency of channel restart operations, reducing the used
H/W resources
- add TSO support for UDP over GRE over VLAN
- add flow counters support for hardware steering (HWS) rules
- use a static memory area to store headers for H/W GRO, leading to
12% RX tput improvement
- Intel (100G, ice, idpf):
- ice: reorganizes layout of Tx and Rx rings for cacheline
locality and utilizes __cacheline_group* macros on the new layouts
- ice: introduces Synchronous Ethernet (SyncE) support
- Meta (fbnic):
- adds debugfs for firmware mailbox and tx/rx rings vectors
- Ethernet virtual:
- geneve: introduce GRO/GSO support for double UDP encapsulation
- Ethernet NICs consumer, and embedded:
- Synopsys (stmmac):
- some code refactoring and cleanups
- RealTek (r8169):
- add support for RTL8127ATF (10G Fiber SFP)
- add dash and LTR support
- Airoha:
- AN8811HB 2.5 Gbps phy support
- Freescale (fec):
- add XDP zero-copy support
- Thunderbolt:
- add get link setting support to allow bonding
- Renesas:
- add support for RZ/G3L GBETH SoC
- Ethernet switches:
- Maxlinear:
- support R(G)MII slow rate configuration
- add support for Intel GSW150
- Motorcomm (yt921x):
- add DCB/QoS support
- TI:
- icssm-prueth: support bridging (STP/RSTP) via the switchdev
framework
- Ethernet PHYs:
- Realtek:
- enable SGMII and 2500Base-X in-band auto-negotiation
- simplify and reunify C22/C45 drivers
- Micrel: convert bindings to DT schema
- CAN:
- move skb headroom content into skb extensions, making CAN metadata
access more robust
- CAN drivers:
- rcar_canfd:
- add support for FD-only mode
- add support for the RZ/T2H SoC
- sja1000: cleanup the CAN state handling
- WiFi:
- implement EPPKE/802.1X over auth frames support
- split up drop reasons better, removing generic RX_DROP
- additional FTM capabilities: 6 GHz support, supported number of
spatial streams and supported number of LTF repetitions
- better mac80211 iterators to enumerate resources
- initial UHR (Wi-Fi 8) support for cfg80211/mac80211
- WiFi drivers:
- Qualcomm/Atheros:
- ath11k: support for Channel Frequency Response measurement
- ath12k: a significant driver refactor to support
multi-wiphy devices and and pave the way for future device support
in the same driver (rather than splitting to ath13k)
- ath12k: support for the QCC2072 chipset
- Intel:
- iwlwifi: partial Neighbor Awareness Networking (NAN) support
- iwlwifi: initial support for U-NII-9 and IEEE 802.11bn
- RealTek (rtw89):
- preparations for RTL8922DE support
- Bluetooth:
- implement setsockopt(BT_PHY) to set the connection packet type/PHY
- set link_policy on incoming ACL connections
- Bluetooth drivers:
- btusb: add support for MediaTek7920, Realtek RTL8761BU and 8851BE
- btqca: add WCN6855 firmware priority selection feature
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=O31Y
-----END PGP SIGNATURE-----
Merge tag 'net-next-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core & protocols:
- A significant effort all around the stack to guide the compiler to
make the right choice when inlining code, to avoid unneeded calls
for small helper and stack canary overhead in the fast-path.
This generates better and faster code with very small or no text
size increases, as in many cases the call generated more code than
the actual inlined helper.
- Extend AccECN implementation so that is now functionally complete,
also allow the user-space enabling it on a per network namespace
basis.
- Add support for memory providers with large (above 4K) rx buffer.
Paired with hw-gro, larger rx buffer sizes reduce the number of
buffers traversing the stack, dincreasing single stream CPU usage
by up to ~30%.
- Do not add HBH header to Big TCP GSO packets. This simplifies the
RX path, the TX path and the NIC drivers, and is possible because
user-space taps can now interpret correctly such packets without
the HBH hint.
- Allow IPv6 routes to be configured with a gateway address that is
resolved out of a different interface than the one specified,
aligning IPv6 to IPv4 behavior.
- Multi-queue aware sch_cake. This makes it possible to scale the
rate shaper of sch_cake across multiple CPUs, while still enforcing
a single global rate on the interface.
- Add support for the nbcon (new buffer console) infrastructure to
netconsole, enabling lock-free, priority-based console operations
that are safer in crash scenarios.
- Improve the TCP ipv6 output path to cache the flow information,
saving cpu cycles, reducing cache line misses and stack use.
- Improve netfilter packet tracker to resolve clashes for most
protocols, avoiding unneeded drops on rare occasions.
- Add IP6IP6 tunneling acceleration to the flowtable infrastructure.
- Reduce tcp socket size by one cache line.
- Notify neighbour changes atomically, avoiding inconsistencies
between the notification sequence and the actual states sequence.
- Add vsock namespace support, allowing complete isolation of vsocks
across different network namespaces.
- Improve xsk generic performances with cache-alignment-oriented
optimizations.
- Support netconsole automatic target recovery, allowing netconsole
to reestablish targets when underlying low-level interface comes
back online.
Driver API:
- Support for switching the working mode (automatic vs manual) of a
DPLL device via netlink.
- Introduce PHY ports representation to expose multiple front-facing
media ports over a single MAC.
- Introduce "rx-polarity" and "tx-polarity" device tree properties,
to generalize polarity inversion requirements for differential
signaling.
- Add helper to create, prepare and enable managed clocks.
Device drivers:
- Add Huawei hinic3 PF etherner driver.
- Add DWMAC glue driver for Motorcomm YT6801 PCIe ethernet
controller.
- Add ethernet driver for MaxLinear MxL862xx switches
- Remove parallel-port Ethernet driver.
- Convert existing driver timestamp configuration reporting to
hwtstamp_get and remove legacy ioctl().
- Convert existing drivers to .get_rx_ring_count(), simplifing the RX
ring count retrieval. Also remove the legacy fallback path.
- Ethernet high-speed NICs:
- Broadcom (bnxt, bng):
- bnxt: add FW interface update to support FEC stats histogram
and NVRAM defragmentation
- bng: add TSO and H/W GRO support
- nVidia/Mellanox (mlx5):
- improve latency of channel restart operations, reducing the
used H/W resources
- add TSO support for UDP over GRE over VLAN
- add flow counters support for hardware steering (HWS) rules
- use a static memory area to store headers for H/W GRO,
leading to 12% RX tput improvement
- Intel (100G, ice, idpf):
- ice: reorganizes layout of Tx and Rx rings for cacheline
locality and utilizes __cacheline_group* macros on the new
layouts
- ice: introduces Synchronous Ethernet (SyncE) support
- Meta (fbnic):
- adds debugfs for firmware mailbox and tx/rx rings vectors
- Ethernet virtual:
- geneve: introduce GRO/GSO support for double UDP encapsulation
- Ethernet NICs consumer, and embedded:
- Synopsys (stmmac):
- some code refactoring and cleanups
- RealTek (r8169):
- add support for RTL8127ATF (10G Fiber SFP)
- add dash and LTR support
- Airoha:
- AN8811HB 2.5 Gbps phy support
- Freescale (fec):
- add XDP zero-copy support
- Thunderbolt:
- add get link setting support to allow bonding
- Renesas:
- add support for RZ/G3L GBETH SoC
- Ethernet switches:
- Maxlinear:
- support R(G)MII slow rate configuration
- add support for Intel GSW150
- Motorcomm (yt921x):
- add DCB/QoS support
- TI:
- icssm-prueth: support bridging (STP/RSTP) via the switchdev
framework
- Ethernet PHYs:
- Realtek:
- enable SGMII and 2500Base-X in-band auto-negotiation
- simplify and reunify C22/C45 drivers
- Micrel: convert bindings to DT schema
- CAN:
- move skb headroom content into skb extensions, making CAN
metadata access more robust
- CAN drivers:
- rcar_canfd:
- add support for FD-only mode
- add support for the RZ/T2H SoC
- sja1000: cleanup the CAN state handling
- WiFi:
- implement EPPKE/802.1X over auth frames support
- split up drop reasons better, removing generic RX_DROP
- additional FTM capabilities: 6 GHz support, supported number of
spatial streams and supported number of LTF repetitions
- better mac80211 iterators to enumerate resources
- initial UHR (Wi-Fi 8) support for cfg80211/mac80211
- WiFi drivers:
- Qualcomm/Atheros:
- ath11k: support for Channel Frequency Response measurement
- ath12k: a significant driver refactor to support multi-wiphy
devices and and pave the way for future device support in the
same driver (rather than splitting to ath13k)
- ath12k: support for the QCC2072 chipset
- Intel:
- iwlwifi: partial Neighbor Awareness Networking (NAN) support
- iwlwifi: initial support for U-NII-9 and IEEE 802.11bn
- RealTek (rtw89):
- preparations for RTL8922DE support
- Bluetooth:
- implement setsockopt(BT_PHY) to set the connection packet type/PHY
- set link_policy on incoming ACL connections
- Bluetooth drivers:
- btusb: add support for MediaTek7920, Realtek RTL8761BU and 8851BE
- btqca: add WCN6855 firmware priority selection feature"
* tag 'net-next-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1254 commits)
bnge/bng_re: Add a new HSI
net: macb: Fix tx/rx malfunction after phy link down and up
af_unix: Fix memleak of newsk in unix_stream_connect().
net: ti: icssg-prueth: Add optional dependency on HSR
net: dsa: add basic initial driver for MxL862xx switches
net: mdio: add unlocked mdiodev C45 bus accessors
net: dsa: add tag format for MxL862xx switches
dt-bindings: net: dsa: add MaxLinear MxL862xx
selftests: drivers: net: hw: Modify toeplitz.c to poll for packets
octeontx2-pf: Unregister devlink on probe failure
net: renesas: rswitch: fix forwarding offload statemachine
ionic: Rate limit unknown xcvr type messages
tcp: inet6_csk_xmit() optimization
tcp: populate inet->cork.fl.u.ip6 in tcp_v6_syn_recv_sock()
tcp: populate inet->cork.fl.u.ip6 in tcp_v6_connect()
ipv6: inet6_csk_xmit() and inet6_csk_update_pmtu() use inet->cork.fl.u.ip6
ipv6: use inet->cork.fl.u.ip6 and np->final in ip6_datagram_dst_update()
ipv6: use np->final in inet6_sk_rebuild_header()
ipv6: add daddr/final storage in struct ipv6_pinfo
net: stmmac: qcom-ethqos: fix qcom_ethqos_serdes_powerup()
...
There is no added value in btintel_pcie_msix_isr() compared to
irq_default_primary_handler().
Using a threaded interrupt without a dedicated primary handler mandates
the IRQF_ONESHOT flag to mask the interrupt source while the threaded
handler is active. Otherwise the interrupt can fire again before the
threaded handler had a chance to run.
Use the default primary interrupt handler by specifying NULL and set
IRQF_ONESHOT so the interrupt source is masked until the secondary
handler is done.
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260128095540.863589-7-bigeasy@linutronix.de
The kfree_skb() function internally checks if the skb is NULL,
so an explicit check before calling it is redundant and can be removed.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch adds the infrastructure that allow the user space program to
talk to intel pcie driver directly for fetching basic driver details.
The changes introduced are referred form
commit 04425292a6 ("Bluetooth: Introduce HCI Driver protocol")
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Due to a hardware bug during suspend/resume, the controller may miss a
doorbell interrupt. To address this, a retry mechanism has been added to
inform the controller before reporting a failure.
Test case:
- run suspend and resume cycles.
Signed-off-by: Ravindra <ravindra@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
During S4 (hibernate), the Bluetooth device loses power. Upon resume,
the driver performs the following actions:
1. Unregisters hdev
2. Calls function level reset
3. Registers hdev
Test case:
- run command sudo rtcwake -m disk -s 60
Signed-off-by: Ravindra <ravindra@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In the current btintel_pcie driver implementation, when an interrupt is
received, the driver checks for the alive cause before the TX/RX cause.
Handling the alive cause involves resetting the TX/RX queue indices.
This flow works correctly when the causes are mutually exclusive.
However, if both cause bits are set simultaneously, the alive cause
resets the queue indices, resulting in an event packet drop and a
command timeout. To fix this issue, the driver is modified to handle all
other causes before checking for the alive cause.
Test case:
Issue is seen with stress reboot scenario - 50x run
[20.337589] Bluetooth: hci0: Device revision is 0
[20.346750] Bluetooth: hci0: Secure boot is enabled
[20.346752] Bluetooth: hci0: OTP lock is disabled
[20.346752] Bluetooth: hci0: API lock is enabled
[20.346752] Bluetooth: hci0: Debug lock is disabled
[20.346753] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[20.346754] Bluetooth: hci0: Bootloader timestamp 2023.43 buildtype 1 build 11631
[20.359070] Bluetooth: hci0: Found device firmware: intel/ibt-00a0-00a1-iml.sfi
[20.371499] Bluetooth: hci0: Boot Address: 0xb02ff800
[20.385769] Bluetooth: hci0: Firmware Version: 166-34.25
[20.538257] Bluetooth: hci0: Waiting for firmware download to complete
[20.554424] Bluetooth: hci0: Firmware loaded in 178651 usecs
[21.081588] Bluetooth: hci0: Timeout (500 ms) on tx completion
[21.096541] Bluetooth: hci0: Failed to send frame (-62)
[21.110240] Bluetooth: hci0: sending frame failed (-62)
[21.138551] Bluetooth: hci0: Failed to send Intel Reset command
[21.170153] Bluetooth: hci0: Intel Soft Reset failed (-62)
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
As device coredumps are not HCI traces, maintain the device coredump at
the driver level and eliminate the dependency on hdev_devcd*()
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: 07e6bddb54 ("Bluetooth: btintel_pcie: Add support for device coredump")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
kzalloc() already zero-initializes the destination buffer 'data', making
strscpy() sufficient for safely copying 'name'. The additional
NUL-padding performed by strscpy_pad() is unnecessary.
Add a new local variable to store the length of 'name' and reuse it
instead of recalculating the same length.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Implement hdev->wakeup() callback to support Wake On BT feature.
Test steps:
1. echo enabled > /sys/bus/pci/devices/0000:00:14.7/power/wakeup
2. connect bluetooth hid device
3. put the system to suspend - rtcwake -m mem -s 300
4. press any key on hid to wake up the system
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This prevents the comments going over 80 columns which is still
required for Bluetooth code.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add Bluetooth CNVi core and platform names to the PCI device table for
each device ID as a comment.
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch implements _suspend() and _resume() functions for the
Bluetooth controller. When the system enters a suspended state, the
driver notifies the controller to perform necessary housekeeping tasks
by writing to the sleep control register and waits for an alive
interrupt. The firmware raises the alive interrupt when it has
transitioned to the D3 state. The same flow occurs when the system
resumes.
Command to test host initiated wakeup after 60 seconds
sudo rtcwake -m mem -s 60
dmesg log (tested on Whale Peak2 on Panther Lake platform)
On system suspend:
[Fri Jul 25 11:05:37 2025] Bluetooth: hci0: device entered into d3 state from d0 in 80 us
On system resume:
[Fri Jul 25 11:06:36 2025] Bluetooth: hci0: device entered into d0 state from d3 in 7117 us
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add support for the BlazarIW Bluetooth core used in the Wildcat Lake
platform.
HCI traces:
< HCI Command: Intel Read Version (0x3f|0x0005) plen 1
Requested Type:
All Supported Types(0xff)
> HCI Event: Command Complete (0x0e) plen 122
Intel Read Version (0x3f|0x0005) ncmd 1
Status: Success (0x00)
.....
CNVi BT(18): 0x00223700 - BlazarIW(0x22)
.....
.....
Signed-off-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The firmware raises an alive interrupt upon sending the HCI_RESET or
BTINTEL_HCI_OP_RESET command. As part of handling the reset command,
firmware initializes the hardware and data path and raises the alive
interrupt. Upon receiving the alive interrupt, the driver must enable
the data path and grant RX buffers to the firmware before sending any
commands.
The alive context maintained in the driver must be updated before
sending BTINTEL_HCI_OP_RESET or HCI_OP_RESET to prevent a potential race
condition where the context is also updated in the threaded IRQ.
The issue was observed in a stress reboot usecase (1/25) using "sudo
reboot" command where the firmware download was failing as the driver
was not granting RX buffer to firmware due to race condition.
Bluetooth: hci0: API lock is disabled
Bluetooth: hci0: Debug lock is disabled
Bluetooth: hci0: Minimum firmware build 1 week 10 2014
Bluetooth: hci0: Bootloader timestamp 2023.43 buildtype 1 build 11631
Bluetooth: hci0: Found device firmware: intel/ibt-00a0-00a1-iml.sfi
Bluetooth: hci0: Boot Address: 0xb0301000
Bluetooth: hci0: Firmware Version: 167-12.25
Bluetooth: hci0: Waiting for firmware download to complete
Bluetooth: hci0: Firmware loaded in 99902 usecs
Bluetooth: hci0: Alive context: fw_dl old_boot_stage: 0xa0db0003
new_boot_stage: 0xa0db0003
Bluetooth: hci0: sent cmd: 0xfc01 alive context changed:
fw_dl -> intel_reset1
Bluetooth: hci0: Waiting for device to boot
Bluetooth: hci0: Device boot timeout
Bluetooth: hci0: Firmware download retry count: 1
Fixes: 05c200c8f0 ("Bluetooth: btintel_pcie: Add handshake between driver and firmware")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The firmware raises an alive interrupt upon receiving the HCI_RESET or
BTINTEL_HCI_OP_RESET (Intel reset - 0xfc01) command. This change fixes
the driver to properly wait for the alive interrupt to avoid driver
sending commands to firmware before it is ready to process.
For details on the handshake between the driver and firmware, refer to
commit 05c200c8f0 ("Bluetooth: btintel_pcie: Add handshake between
driver and firmware").
As the driver needs to handle two interrupts for HCI_OP_RESET and
BTINTEL_HCI_OP_RESET, the firmware ensures that the TX completion
interrupt is always followed by the alive interrupt.
Fixes: 05c200c8f0 ("Bluetooth: btintel_pcie: Add handshake between driver and firmware")
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use macro for Intel Reset command (0xfc01) instead of hard coded value.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This rewords the term restart with recovery since the intend is for
hardware recovery not a regular restart, also remove some debug logs
which might just clutter the output informing the recovery counter which
isn't really useful for regular users.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver supports Function Level Reset (FLR) to recover the controller
upon hardware exceptions or hci command timeouts. FLR is triggered only
when no prior reset has occurred within the retry window, with a maximum
of one FLR allowed within this window.
This patch is tested by,
echo 1 > /sys/class/bluetooth/hciX/reset
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The 'quirks' member already ran out of bits on some platforms some time
ago. Replace the integer member by a bitmap in order to have enough bits
in future. Replace raw bit operations by accessor macros.
Fixes: ff26b2dd65 ("Bluetooth: Add quirk for broken READ_VOICE_SETTING")
Fixes: 127881334e ("Bluetooth: Add quirk for broken READ_PAGE_SCAN_TYPE")
Suggested-by: Pauli Virtanen <pav@iki.fi>
Tested-by: Ivan Pravdin <ipravdin.official@gmail.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
During firmware download, if an error occurs, interrupts must be
disabled, synchronized, and re-enabled before retrying the download.
This change ensures proper interrupt handling to prevent race
conditions.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Modify the driver to post 3 fewer buffers than the maximum rx buffers
(64) allowed for the firmware. This change mitigates a hardware issue
causing a race condition in the firmware, improving stability and data
handling.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This change addresses latency issues observed in HID use cases where
events arrive in bursts. By increasing the Rx descriptor count to 64,
the firmware can handle bursty data more effectively, reducing latency
and preventing buffer overflows.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver was posting only 6 rx buffers, despite the maximum rx buffers
being defined as 16. Having fewer RX buffers caused firmware exceptions
in HID use cases when events arrived in bursts.
Exception seen on android 6.12 kernel.
E Bluetooth: hci0: Received hw exception interrupt
E Bluetooth: hci0: Received gp1 mailbox interrupt
D Bluetooth: hci0: 00000000: ff 3e 87 80 03 01 01 01 03 01 0c 0d 02 1c 10 0e
D Bluetooth: hci0: 00000010: 01 00 05 14 66 b0 28 b0 c0 b0 28 b0 ac af 28 b0
D Bluetooth: hci0: 00000020: 14 f1 28 b0 00 00 00 00 fa 04 00 00 00 00 40 10
D Bluetooth: hci0: 00000030: 08 00 00 00 7a 7a 7a 7a 47 00 fb a0 10 00 00 00
D Bluetooth: hci0: 00000000: 10 01 0a
E Bluetooth: hci0: ---- Dump of debug registers —
E Bluetooth: hci0: boot stage: 0xe0fb0047
E Bluetooth: hci0: ipc status: 0x00000004
E Bluetooth: hci0: ipc control: 0x00000000
E Bluetooth: hci0: ipc sleep control: 0x00000000
E Bluetooth: hci0: mbox_1: 0x00badbad
E Bluetooth: hci0: mbox_2: 0x0000101c
E Bluetooth: hci0: mbox_3: 0x00000008
E Bluetooth: hci0: mbox_4: 0x7a7a7a7a
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
All Intel diagnostic events are part of HCI traces and there is no need
to generate coredump for the same.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Due to a hardware issue, there is a possibility that the driver may miss
an MSIx interrupt on the RX/TX data path. Since the TX and RX paths are
independent, when a TX MSIx interrupt occurs, the driver can check the
RX queue for any pending data and process it if present. The same
approach applies to the RX path.
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reuse the skb buffer provided by the PCIe driver to pass it onto the
stack, instead of copying it to a new skb.
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Remove the unwanted leading whitespace.
Fixes: 6ed8304738 ("Bluetooth: btintel_pcie: Setup buffers for firmware traces")
Fixes: bb3569ac36 ("Bluetooth: btintel: Add DSBR support for ScP")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the following warning:
drivers/bluetooth/btintel_pcie.c:695:20: warning: unused function 'btintel_pcie_in_rom' [-Wunused-function]
695 | static inline bool btintel_pcie_in_rom(struct btintel_pcie_data *data)
| ^~~~~~~~~~~~~~~~~~~
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Driver dumps device core dump on firmware exception.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On hardware error, controller writes hardware error event and optional
vendor specific hci events in device memory in TLV format and raises
MSIX interrupt. Driver reads the device memory and passes the events to
the stack for further processing.
Co-developed-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Vijay Satija <vijay.satija@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
