Writeback suffers from the same problem as recompression did before -
target slot selection for writeback is just a simple iteration over
zram->table entries (stored pages) which selects suboptimal targets for
writeback. This is especially problematic for writeback, because we
uncompress objects before writeback so each of them takes 4K out of
limited writeback storage. For example, when we take a 48 bytes slot and
store it as a 4K object to writeback device we only save 48 bytes of
memory (release from zsmalloc pool). We naturally want to pick the
largest objects for writeback, because then each writeback will release
the largest amount of memory.
This patch applies the same solution and strategy as for recompression
target selection: pp control (post-process) with 16 buckets of candidate
pp slots. Slots are assigned to pp buckets based on sizes - the larger
the slot the higher the group index. This gives us sorted by size lists
of candidate slots (in linear time), so that among post-processing
candidate slots we always select the largest ones first and maximize the
memory saving.
TEST
====
A very simple demonstration: zram is configured with a writeback device.
A limited writeback (wb_limit 2500 pages) is performed then, with a log of
sizes of slots that were written back. You can see that patched zram
selects slots for recompression in significantly different manner, which
leads to higher memory savings (see column #2 of mm_stat output).
BASE
----
*** initial state of zram device
/sys/block/zram0/mm_stat
1750327296 619765836 631902208 0 631902208 1 0 34278 34278
*** writeback idle wb_limit 2500
/sys/block/zram0/mm_stat
1750327296 617622333 631578624 0 631902208 1 0 34278 34278
Sizes of selected objects for writeback:
... 193 349 46 46 46 46 852 1002 543 162 107 49 34 34 34 ...
PATCHED
-------
*** initial state of zram device
/sys/block/zram0/mm_stat
1750319104 619760957 631992320 0 631992320 1 0 34278 34278
*** writeback idle wb_limit 2500
/sys/block/zram0/mm_stat
1750319104 612672056 626135040 0 631992320 1 0 34278 34278
Sizes of selected objects for writeback:
... 3667 3580 3581 3580 3581 3581 3581 3231 3211 3203 3231 3246 ...
Note, pp-slots are not strictly sorted, there is a PP_BUCKET_SIZE_RANGE
variation of sizes within particular bucket.
Link: https://lkml.kernel.org/r/20240917021020.883356-5-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Target slot selection for recompression is just a simple iteration over
zram->table entries (stored pages) from slot 0 to max slot. Given that
zram->table slots are written in random order and are not sorted by size,
a simple iteration over slots selects suboptimal targets for
recompression. This is not a problem if we recompress every single
zram->table slot, but we never do that in reality. In reality we limit
the number of slots we can recompress (via max_pages parameter) and hence
proper slot selection becomes very important. The strategy is quite
simple, suppose we have two candidate slots for recompression, one of size
48 bytes and one of size 2800 bytes, and we can recompress only one, then
it certainly makes more sense to pick 2800 entry for recompression.
Because even if we manage to compress 48 bytes objects even further the
savings are going to be very small. Potential savings after good
re-compression of 2800 bytes objects are much higher.
This patch reworks slot selection and introduces the strategy described
above: among candidate slots always select the biggest ones first.
For that the patch introduces zram_pp_ctl (post-processing) structure
which holds NUM_PP_BUCKETS pp buckets of slots. Slots are assigned to a
particular group based on their sizes - the larger the size of the slot
the higher the group index. This, basically, sorts slots by size in liner
time (we still perform just one iteration over zram->table slots). When
we select slot for recompression we always first lookup in higher pp
buckets (those that hold the largest slots). Which achieves the desired
behavior.
TEST
====
A very simple demonstration: zram is configured with zstd, and zstd with
dict as a recompression stream. A limited (max 4096 pages) recompression
is performed then, with a log of sizes of slots that were recompressed.
You can see that patched zram selects slots for recompression in
significantly different manner, which leads to higher memory savings (see
column #2 of mm_stat output).
BASE
----
*** initial state of zram device
/sys/block/zram0/mm_stat
1750994944 504491413 514203648 0 514203648 1 0 34204 34204
*** recompress idle max_pages=4096
/sys/block/zram0/mm_stat
1750994944 504262229 514953216 0 514203648 1 0 34204 34204
Sizes of selected objects for recompression:
... 45 58 24 226 91 40 24 24 24 424 2104 93 2078 2078 2078 959 154 ...
PATCHED
-------
*** initial state of zram device
/sys/block/zram0/mm_stat
1750982656 504492801 514170880 0 514170880 1 0 34204 34204
*** recompress idle max_pages=4096
/sys/block/zram0/mm_stat
1750982656 503716710 517586944 0 514170880 1 0 34204 34204
Sizes of selected objects for recompression:
... 3680 3694 3667 3590 3614 3553 3537 3548 3550 3542 3543 3537 ...
Note, pp-slots are not strictly sorted, there is a PP_BUCKET_SIZE_RANGE
variation of sizes within particular bucket.
[senozhatsky@chromium.org: do not skip the first bucket]
Link: https://lkml.kernel.org/r/20241001085634.1948384-1-senozhatsky@chromium.org
Link: https://lkml.kernel.org/r/20240917021020.883356-4-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Both recompress and writeback soon will unlock slots during processing,
which makes things too complex wrt possible race-conditions. We still
want to clear PP_SLOT in slot_free, because this is how we figure out that
slot that was selected for post-processing has been released under us and
when we start post-processing we check if slot still has PP_SLOT set. At
the same time, theoretically, we can have something like this:
CPU0 CPU1
recompress
scan slots
set PP_SLOT
unlock slot
slot_free
clear PP_SLOT
allocate PP_SLOT
writeback
scan slots
set PP_SLOT
unlock slot
select PP-slot
test PP_SLOT
So recompress will not detect that slot has been re-used and re-selected
for concurrent writeback post-processing.
Make sure that we only permit on post-processing operation at a time. So
now recompress and writeback post-processing don't race against each
other, we only need to handle slot re-use (slot_free and write), which is
handled individually by each pp operation.
Having recompress and writeback competing for the same slots is not
exactly good anyway (can't imagine anyone doing that).
Link: https://lkml.kernel.org/r/20240917021020.883356-3-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "zram: optimal post-processing target selection", v5.
Problem:
--------
Both recompression and writeback perform a very simple linear scan of all
zram slots in search for post-processing (writeback or recompress)
candidate slots. This often means that we pick the worst candidate for pp
(post-processing), e.g. a 48 bytes object for writeback, which is nearly
useless, because it only releases 48 bytes from zsmalloc pool, but
consumes an entire 4K slot in the backing device. Similarly,
recompression of an 48 bytes objects is unlikely to save more memory that
recompression of a 3000 bytes object. Both recompression and writeback
consume constrained resources (CPU time, batter, backing device storage
space) and quite often have a (daily) limit on the number of items they
post-process, so we should utilize those constrained resources in the most
optimal way.
Solution:
---------
This patch reworks the way we select pp targets. We, quite clearly, want
to sort all the candidates and always pick the largest, be it
recompression or writeback. Especially for writeback, because the larger
object we writeback the more memory we release. This series introduces
concept of pp buckets and pp scan/selection.
The scan step is a simple iteration over all zram->table entries, just
like what we currently do, but we don't post-process a candidate slot
immediately. Instead we assign it to a PP (post-processing) bucket. PP
bucket is, basically, a list which holds pp candidate slots that belong to
the same size class. PP buckets are 64 bytes apart, slots are not
strictly sorted within a bucket there is a 64 bytes variance.
The select step simply iterates over pp buckets from highest to lowest and
picks all candidate slots a particular buckets contains. So this gives us
sorted candidates (in linear time) and allows us to select most optimal
(largest) candidates for post-processing first.
This patch (of 7):
This flag indicates that the slot was selected as a candidate slot for
post-processing (pp) and was assigned to a pp bucket. It does not
necessarily mean that the slot is currently under post-processing, but may
mean so. The slot can loose its PP_SLOT flag, while still being in the
pp-bucket, if it's accessed or slot_free-ed.
Link: https://lkml.kernel.org/r/20240917021020.883356-1-senozhatsky@chromium.org
Link: https://lkml.kernel.org/r/20240917021020.883356-2-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
max_zone_append_sectors differs from all other queue limits in that the
final value used is not stored in the queue_limits but needs to be
obtained using queue_limits_max_zone_append_sectors helper. This not
only adds (tiny) extra overhead to the I/O path, but also can be easily
forgotten in file system code.
Add a new max_hw_zone_append_sectors value to queue_limits which is
set by the driver, and calculate max_zone_append_sectors from that and
the other inputs in blk_validate_zoned_limits, similar to how
max_sectors is calculated to fix this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241104073955.112324-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A bdev discard granularity is always at least SECTOR_SIZE, so don't check
for a zero value.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20241101092215.422428-1-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
My colleague Wupeng found the following problems during fault injection:
BUG: unable to handle page fault for address: fffffbfff809d073
PGD 6e648067 P4D 123ec8067 PUD 123ec4067 PMD 100e38067 PTE 0
Oops: Oops: 0000 [#1] PREEMPT SMP KASAN NOPTI
CPU: 5 UID: 0 PID: 755 Comm: modprobe Not tainted 6.12.0-rc3+ #17
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.16.1-2.fc37 04/01/2014
RIP: 0010:__asan_load8+0x4c/0xa0
...
Call Trace:
<TASK>
blkdev_put_whole+0x41/0x70
bdev_release+0x1a3/0x250
blkdev_release+0x11/0x20
__fput+0x1d7/0x4a0
task_work_run+0xfc/0x180
syscall_exit_to_user_mode+0x1de/0x1f0
do_syscall_64+0x6b/0x170
entry_SYSCALL_64_after_hwframe+0x76/0x7e
loop_init() is calling loop_add() after __register_blkdev() succeeds and
is ignoring disk_add() failure from loop_add(), for loop_add() failure
is not fatal and successfully created disks are already visible to
bdev_open().
brd_init() is currently calling brd_alloc() before __register_blkdev()
succeeds and is releasing successfully created disks when brd_init()
returns an error. This can cause UAF for the latter two case:
case 1:
T1:
modprobe brd
brd_init
brd_alloc(0) // success
add_disk
disk_scan_partitions
bdev_file_open_by_dev // alloc file
fput // won't free until back to userspace
brd_alloc(1) // failed since mem alloc error inject
// error path for modprobe will release code segment
// back to userspace
__fput
blkdev_release
bdev_release
blkdev_put_whole
bdev->bd_disk->fops->release // fops is freed now, UAF!
case 2:
T1: T2:
modprobe brd
brd_init
brd_alloc(0) // success
open(/dev/ram0)
brd_alloc(1) // fail
// error path for modprobe
close(/dev/ram0)
...
/* UAF! */
bdev->bd_disk->fops->release
Fix this problem by following what loop_init() does. Besides,
reintroduce brd_devices_mutex to help serialize modifications to
brd_list.
Fixes: 7f9b348cb5 ("brd: convert to blk_alloc_disk/blk_cleanup_disk")
Reported-by: Wupeng Ma <mawupeng1@huawei.com>
Signed-off-by: Yang Erkun <yangerkun@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20241030034914.907829-1-yangerkun@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ublk currently supports the following behaviors on ublk server exit:
A: outstanding I/Os get errors, subsequently issued I/Os get errors
B: outstanding I/Os get errors, subsequently issued I/Os queue
C: outstanding I/Os get reissued, subsequently issued I/Os queue
and the following behaviors for recovery of preexisting block devices by
a future incarnation of the ublk server:
1: ublk devices stopped on ublk server exit (no recovery possible)
2: ublk devices are recoverable using start/end_recovery commands
The userspace interface allows selection of combinations of these
behaviors using flags specified at device creation time, namely:
default behavior: A + 1
UBLK_F_USER_RECOVERY: B + 2
UBLK_F_USER_RECOVERY|UBLK_F_USER_RECOVERY_REISSUE: C + 2
The behavior A + 2 is currently unsupported. Add support for this
behavior under the new flag combination
UBLK_F_USER_RECOVERY|UBLK_F_USER_RECOVERY_FAIL_IO.
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20241007182419.3263186-5-ushankar@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Save some lines by merging stop_work and quiesce_work into nosrv_work,
which looks at the recovery flags and does the right thing when the "no
ublk server" condition is detected.
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20241007182419.3263186-4-ushankar@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ublk currently supports the following behaviors on ublk server exit:
A: outstanding I/Os get errors, subsequently issued I/Os get errors
B: outstanding I/Os get errors, subsequently issued I/Os queue
C: outstanding I/Os get reissued, subsequently issued I/Os queue
and the following behaviors for recovery of preexisting block devices by
a future incarnation of the ublk server:
1: ublk devices stopped on ublk server exit (no recovery possible)
2: ublk devices are recoverable using start/end_recovery commands
The userspace interface allows selection of combinations of these
behaviors using flags specified at device creation time, namely:
default behavior: A + 1
UBLK_F_USER_RECOVERY: B + 2
UBLK_F_USER_RECOVERY|UBLK_F_USER_RECOVERY_REISSUE: C + 2
We can't easily change the userspace interface to allow independent
selection of one of {A, B, C} and one of {1, 2}, but we can refactor the
internal helpers which test for the flags. Replace the existing helpers
with the following set:
ublk_nosrv_should_reissue_outstanding: tests for behavior C
ublk_nosrv_[dev_]should_queue_io: tests for behavior B
ublk_nosrv_should_stop_dev: tests for behavior 1
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20241007182419.3263186-3-ushankar@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Setting UBLK_F_USER_RECOVERY_REISSUE without also setting
UBLK_F_USER_RECOVERY is currently silently equivalent to not setting any
recovery flags at all, even though that's obviously not intended. Check
for this case and fail add_dev (with a paranoid warning to aid debugging
any program which might rely on the old behavior) with EINVAL if it is
detected.
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20241007182419.3263186-2-ushankar@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Deprecation period of reiserfs ends with the end of this year so it is
time to remove it from the kernel.
Acked-by: Darrick J. Wong <djwong@kernel.org>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAmcSk4AQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpuuXD/0UERdP+djJNoXBW5Mv7U5a4rJ7ZgfPL7ku
z3ZfdnNYGitZhYkVjNQ60TLzXRQyUaIIxMVBWzkb59I6ixmuQbzm/lC55B6s/FIR
bfT3afe1WRgLCaFbStu91qRs/44Mq4yK6wXcIU7LwutRT/5cqZwelqRZLK7DMFln
zlGX4zNrCMRUDTr6PLa6CvyY4dmQSL17Ib1ypcKXjGs5YjDntzSrIsKVT1Wayans
WroGGPG6W7r2c2kn8pe4uPIjZVfMUF2vrdIs0KEYaAQOC7ppEucCgDZMEWRs7kdH
63hheudJjVSwLF/qYnXNHe/Bz12QCZohPp6UsqRpC8o96Ralgo6Q+FxkXsVelMXW
JKhtDqYGBDHOQrjrEWN1rnYw/DauEQAgvOtdVfEx2IBzPsG07cB8yv8MNA90H9QH
KStI7h9qnBEMMNcXX8prOymCHNWAeuF4mbitVrRfSfEVm/0BbQ19qoyGrvwNFgEf
6T+4Xj/P+FsiLVe8vsgBZDaxEEU5Ifd/rki/QFVk/2z72BBZxmdf2nm51SOM28V7
HGMHwJI3H8rdmPXvt5Q/ve6GWNOYLO5PSAJgSSe96UStvtsAHGB4eM+LykdnE7cI
SoytU5KfAM8DD6wnyHIgYuvJyZWrmLoVDrRjym8emc2KrJOe7qg+Ah4ERcNTCnhl
nw50f27G4w==
=waNY
-----END PGP SIGNATURE-----
Merge tag 'block-6.12-20241018' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- Fix target passthrough identifier (Nilay)
- Fix tcp locking (Hannes)
- Replace list with sbitmap for tracking RDMA rsp tags (Guixen)
- Remove unnecessary fallthrough statements (Tokunori)
- Remove ready-without-media support (Greg)
- Fix multipath partition scan deadlock (Keith)
- Fix concurrent PCI reset and remove queue mapping (Maurizio)
- Fabrics shutdown fixes (Nilay)
- Fix for a kerneldoc warning (Keith)
- Fix a race with blk-rq-qos and wakeups (Omar)
- Cleanup of checking for always-set tag_set (SurajSonawane2415)
- Fix for a crash with CPU hotplug notifiers (Ming)
- Don't allow zero-copy ublk on unprivileged device (Ming)
- Use array_index_nospec() for CDROM (Josh)
- Remove dead code in drbd (David)
- Tweaks to elevator loading (Breno)
* tag 'block-6.12-20241018' of git://git.kernel.dk/linux:
cdrom: Avoid barrier_nospec() in cdrom_ioctl_media_changed()
nvme: use helper nvme_ctrl_state in nvme_keep_alive_finish function
nvme: make keep-alive synchronous operation
nvme-loop: flush off pending I/O while shutting down loop controller
nvme-pci: fix race condition between reset and nvme_dev_disable()
ublk: don't allow user copy for unprivileged device
blk-rq-qos: fix crash on rq_qos_wait vs. rq_qos_wake_function race
nvme-multipath: defer partition scanning
blk-mq: setup queue ->tag_set before initializing hctx
elevator: Remove argument from elevator_find_get
elevator: do not request_module if elevator exists
drbd: Remove unused conn_lowest_minor
nvme: disable CC.CRIME (NVME_CC_CRIME)
nvme: delete unnecessary fallthru comment
nvmet-rdma: use sbitmap to replace rsp free list
block: Fix elevator_get_default() checking for NULL q->tag_set
nvme: tcp: avoid race between queue_lock lock and destroy
nvmet-passthru: clear EUID/NGUID/UUID while using loop target
block: fix blk_rq_map_integrity_sg kernel-doc
UBLK_F_USER_COPY requires userspace to call write() on ublk char
device for filling request buffer, and unprivileged device can't
be trusted.
So don't allow user copy for unprivileged device.
Cc: stable@vger.kernel.org
Fixes: 1172d5b8be ("ublk: support user copy")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20241016134847.2911721-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that we got the kernel `Box` type in place, convert all existing
`Box` users to make use of it.
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Reviewed-by: Benno Lossin <benno.lossin@proton.me>
Reviewed-by: Gary Guo <gary@garyguo.net>
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://lore.kernel.org/r/20241004154149.93856-13-dakr@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
conn_lowest_minor() last use was removed by 2011 commit
69a227731a ("drbd: Pass a peer device to a number of fuctions")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20241010204426.277535-1-linux@treblig.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
For fixing CVE-2023-6270, f98364e926 ("aoe: fix the potential
use-after-free problem in aoecmd_cfg_pkts") makes tx() calling dev_put()
instead of doing in aoecmd_cfg_pkts(). It avoids that the tx() runs
into use-after-free.
Then Nicolai Stange found more places in aoe have potential use-after-free
problem with tx(). e.g. revalidate(), aoecmd_ata_rw(), resend(), probe()
and aoecmd_cfg_rsp(). Those functions also use aoenet_xmit() to push
packet to tx queue. So they should also use dev_hold() to increase the
refcnt of skb->dev.
On the other hand, moving dev_put() to tx() causes that the refcnt of
skb->dev be reduced to a negative value, because corresponding
dev_hold() are not called in revalidate(), aoecmd_ata_rw(), resend(),
probe(), and aoecmd_cfg_rsp(). This patch fixed this issue.
Cc: stable@vger.kernel.org
Link: https://nvd.nist.gov/vuln/detail/CVE-2023-6270
Fixes: f98364e926 ("aoe: fix the potential use-after-free problem in aoecmd_cfg_pkts")
Reported-by: Nicolai Stange <nstange@suse.com>
Signed-off-by: Chun-Yi Lee <jlee@suse.com>
Link: https://lore.kernel.org/stable/20240624064418.27043-1-jlee%40suse.com
Link: https://lore.kernel.org/r/20241002035458.24401-1-jlee@suse.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There's a focus on fixes for the memfd_pin_folios() work which was added
into 6.11. Apart from that, the usual shower of singleton fixes.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZvbhSAAKCRDdBJ7gKXxA
jp8CAP47txk2c+tBLggog2MkQamADY5l5MT6E3fYq3ghSiKtVQEAnqX3LiQJ02tB
o9LcPcVrM90QntpKrLP1CpWCVdR+zA8=
=e0QC
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2024-09-27-09-45' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"19 hotfixes. 13 are cc:stable.
There's a focus on fixes for the memfd_pin_folios() work which was
added into 6.11. Apart from that, the usual shower of singleton fixes"
* tag 'mm-hotfixes-stable-2024-09-27-09-45' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
ocfs2: fix uninit-value in ocfs2_get_block()
zram: don't free statically defined names
memory tiers: use default_dram_perf_ref_source in log message
Revert "list: test: fix tests for list_cut_position()"
kselftests: mm: fix wrong __NR_userfaultfd value
compiler.h: specify correct attribute for .rodata..c_jump_table
mm/damon/Kconfig: update DAMON doc URL
mm: kfence: fix elapsed time for allocated/freed track
ocfs2: fix deadlock in ocfs2_get_system_file_inode
ocfs2: reserve space for inline xattr before attaching reflink tree
mm: migrate: annotate data-race in migrate_folio_unmap()
mm/hugetlb: simplify refs in memfd_alloc_folio
mm/gup: fix memfd_pin_folios alloc race panic
mm/gup: fix memfd_pin_folios hugetlb page allocation
mm/hugetlb: fix memfd_pin_folios resv_huge_pages leak
mm/hugetlb: fix memfd_pin_folios free_huge_pages leak
mm/filemap: fix filemap_get_folios_contig THP panic
mm: make SPLIT_PTE_PTLOCKS depend on SMP
tools: fix shared radix-tree build
no_llseek had been defined to NULL two years ago, in commit 868941b144
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When CONFIG_ZRAM_MULTI_COMP isn't set ZRAM_SECONDARY_COMP can hold
default_compressor, because it's the same offset as ZRAM_PRIMARY_COMP, so
we need to make sure that we don't attempt to kfree() the statically
defined compressor name.
This is detected by KASAN.
==================================================================
Call trace:
kfree+0x60/0x3a0
zram_destroy_comps+0x98/0x198 [zram]
zram_reset_device+0x22c/0x4a8 [zram]
reset_store+0x1bc/0x2d8 [zram]
dev_attr_store+0x44/0x80
sysfs_kf_write+0xfc/0x188
kernfs_fop_write_iter+0x28c/0x428
vfs_write+0x4dc/0x9b8
ksys_write+0x100/0x1f8
__arm64_sys_write+0x74/0xb8
invoke_syscall+0xd8/0x260
el0_svc_common.constprop.0+0xb4/0x240
do_el0_svc+0x48/0x68
el0_svc+0x40/0xc8
el0t_64_sync_handler+0x120/0x130
el0t_64_sync+0x190/0x198
==================================================================
Link: https://lkml.kernel.org/r/20240923164843.1117010-1-andrej.skvortzov@gmail.com
Fixes: 684826f827 ("zram: free secondary algorithms names")
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reported-by: Venkat Rao Bagalkote <venkat88@linux.vnet.ibm.com>
Closes: https://lore.kernel.org/lkml/57130e48-dbb6-4047-a8c7-ebf5aaea93f4@linux.vnet.ibm.com/
Tested-by: Venkat Rao Bagalkote <venkat88@linux.vnet.ibm.com>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Venkat Rao Bagalkote <venkat88@linux.vnet.ibm.com>
Cc: Chris Li <chrisl@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=yiWu
-----END PGP SIGNATURE-----
Merge tag 'for-6.12/block-20240925' of git://git.kernel.dk/linux
Pull more block updates from Jens Axboe:
- Improve blk-integrity segment counting and merging (Keith)
- NVMe pull request via Keith:
- Multipath fixes (Hannes)
- Sysfs attribute list NULL terminate fix (Shin'ichiro)
- Remove problematic read-back (Keith)
- Fix for a regression with the IO scheduler switching freezing from
6.11 (Damien)
- Use a raw spinlock for sbitmap, as it may get called from preempt
disabled context (Ming)
- Cleanup for bd_claiming waiting, using var_waitqueue() rather than
the bit waitqueues, as that more accurately describes that it does
(Neil)
- Various cleanups (Kanchan, Qiu-ji, David)
* tag 'for-6.12/block-20240925' of git://git.kernel.dk/linux:
nvme: remove CC register read-back during enabling
nvme: null terminate nvme_tls_attrs
nvme-multipath: avoid hang on inaccessible namespaces
nvme-multipath: system fails to create generic nvme device
lib/sbitmap: define swap_lock as raw_spinlock_t
block: Remove unused blk_limits_io_{min,opt}
drbd: Fix atomicity violation in drbd_uuid_set_bm()
block: Fix elv_iosched_local_module handling of "none" scheduler
block: remove bogus union
block: change wait on bd_claiming to use a var_waitqueue
blk-integrity: improved sg segment mapping
block: unexport blk_rq_count_integrity_sg
nvme-rdma: use request to get integrity segments
scsi: use request to get integrity segments
block: provide a request helper for user integrity segments
blk-integrity: consider entire bio list for merging
blk-integrity: properly account for segments
blk-mq: set the nr_integrity_segments from bio
blk-mq: unconditional nr_integrity_segments
this pull request are:
"Align kvrealloc() with krealloc()" from Danilo Krummrich. Adds
consistency to the APIs and behaviour of these two core allocation
functions. This also simplifies/enables Rustification.
"Some cleanups for shmem" from Baolin Wang. No functional changes - mode
code reuse, better function naming, logic simplifications.
"mm: some small page fault cleanups" from Josef Bacik. No functional
changes - code cleanups only.
"Various memory tiering fixes" from Zi Yan. A small fix and a little
cleanup.
"mm/swap: remove boilerplate" from Yu Zhao. Code cleanups and
simplifications and .text shrinkage.
"Kernel stack usage histogram" from Pasha Tatashin and Shakeel Butt. This
is a feature, it adds new feilds to /proc/vmstat such as
$ grep kstack /proc/vmstat
kstack_1k 3
kstack_2k 188
kstack_4k 11391
kstack_8k 243
kstack_16k 0
which tells us that 11391 processes used 4k of stack while none at all
used 16k. Useful for some system tuning things, but partivularly useful
for "the dynamic kernel stack project".
"kmemleak: support for percpu memory leak detect" from Pavel Tikhomirov.
Teaches kmemleak to detect leaksage of percpu memory.
"mm: memcg: page counters optimizations" from Roman Gushchin. "3
independent small optimizations of page counters".
"mm: split PTE/PMD PT table Kconfig cleanups+clarifications" from David
Hildenbrand. Improves PTE/PMD splitlock detection, makes powerpc/8xx work
correctly by design rather than by accident.
"mm: remove arch_make_page_accessible()" from David Hildenbrand. Some
folio conversions which make arch_make_page_accessible() unneeded.
"mm, memcg: cg2 memory{.swap,}.peak write handlers" fro David Finkel.
Cleans up and fixes our handling of the resetting of the cgroup/process
peak-memory-use detector.
"Make core VMA operations internal and testable" from Lorenzo Stoakes.
Rationalizaion and encapsulation of the VMA manipulation APIs. With a
view to better enable testing of the VMA functions, even from a
userspace-only harness.
"mm: zswap: fixes for global shrinker" from Takero Funaki. Fix issues in
the zswap global shrinker, resulting in improved performance.
"mm: print the promo watermark in zoneinfo" from Kaiyang Zhao. Fill in
some missing info in /proc/zoneinfo.
"mm: replace follow_page() by folio_walk" from David Hildenbrand. Code
cleanups and rationalizations (conversion to folio_walk()) resulting in
the removal of follow_page().
"improving dynamic zswap shrinker protection scheme" from Nhat Pham. Some
tuning to improve zswap's dynamic shrinker. Significant reductions in
swapin and improvements in performance are shown.
"mm: Fix several issues with unaccepted memory" from Kirill Shutemov.
Improvements to the new unaccepted memory feature,
"mm/mprotect: Fix dax puds" from Peter Xu. Implements mprotect on DAX
PUDs. This was missing, although nobody seems to have notied yet.
"Introduce a store type enum for the Maple tree" from Sidhartha Kumar.
Cleanups and modest performance improvements for the maple tree library
code.
"memcg: further decouple v1 code from v2" from Shakeel Butt. Move more
cgroup v1 remnants away from the v2 memcg code.
"memcg: initiate deprecation of v1 features" from Shakeel Butt. Adds
various warnings telling users that memcg v1 features are deprecated.
"mm: swap: mTHP swap allocator base on swap cluster order" from Chris Li.
Greatly improves the success rate of the mTHP swap allocation.
"mm: introduce numa_memblks" from Mike Rapoport. Moves various disparate
per-arch implementations of numa_memblk code into generic code.
"mm: batch free swaps for zap_pte_range()" from Barry Song. Greatly
improves the performance of munmap() of swap-filled ptes.
"support large folio swap-out and swap-in for shmem" from Baolin Wang.
With this series we no longer split shmem large folios into simgle-page
folios when swapping out shmem.
"mm/hugetlb: alloc/free gigantic folios" from Yu Zhao. Nice performance
improvements and code reductions for gigantic folios.
"support shmem mTHP collapse" from Baolin Wang. Adds support for
khugepaged's collapsing of shmem mTHP folios.
"mm: Optimize mseal checks" from Pedro Falcato. Fixes an mprotect()
performance regression due to the addition of mseal().
"Increase the number of bits available in page_type" from Matthew Wilcox.
Increases the number of bits available in page_type!
"Simplify the page flags a little" from Matthew Wilcox. Many legacy page
flags are now folio flags, so the page-based flags and their
accessors/mutators can be removed.
"mm: store zero pages to be swapped out in a bitmap" from Usama Arif. An
optimization which permits us to avoid writing/reading zero-filled zswap
pages to backing store.
"Avoid MAP_FIXED gap exposure" from Liam Howlett. Fixes a race window
which occurs when a MAP_FIXED operqtion is occurring during an unrelated
vma tree walk.
"mm: remove vma_merge()" from Lorenzo Stoakes. Major rotorooting of the
vma_merge() functionality, making ot cleaner, more testable and better
tested.
"misc fixups for DAMON {self,kunit} tests" from SeongJae Park. Minor
fixups of DAMON selftests and kunit tests.
"mm: memory_hotplug: improve do_migrate_range()" from Kefeng Wang. Code
cleanups and folio conversions.
"Shmem mTHP controls and stats improvements" from Ryan Roberts. Cleanups
for shmem controls and stats.
"mm: count the number of anonymous THPs per size" from Barry Song. Expose
additional anon THP stats to userspace for improved tuning.
"mm: finish isolate/putback_lru_page()" from Kefeng Wang: more folio
conversions and removal of now-unused page-based APIs.
"replace per-quota region priorities histogram buffer with per-context
one" from SeongJae Park. DAMON histogram rationalization.
"Docs/damon: update GitHub repo URLs and maintainer-profile" from SeongJae
Park. DAMON documentation updates.
"mm/vdpa: correct misuse of non-direct-reclaim __GFP_NOFAIL and improve
related doc and warn" from Jason Wang: fixes usage of page allocator
__GFP_NOFAIL and GFP_ATOMIC flags.
"mm: split underused THPs" from Yu Zhao. Improve THP=always policy - this
was overprovisioning THPs in sparsely accessed memory areas.
"zram: introduce custom comp backends API" frm Sergey Senozhatsky. Add
support for zram run-time compression algorithm tuning.
"mm: Care about shadow stack guard gap when getting an unmapped area" from
Mark Brown. Fix up the various arch_get_unmapped_area() implementations
to better respect guard areas.
"Improve mem_cgroup_iter()" from Kinsey Ho. Improve the reliability of
mem_cgroup_iter() and various code cleanups.
"mm: Support huge pfnmaps" from Peter Xu. Extends the usage of huge
pfnmap support.
"resource: Fix region_intersects() vs add_memory_driver_managed()" from
Huang Ying. Fix a bug in region_intersects() for systems with CXL memory.
"mm: hwpoison: two more poison recovery" from Kefeng Wang. Teaches a
couple more code paths to correctly recover from the encountering of
poisoned memry.
"mm: enable large folios swap-in support" from Barry Song. Support the
swapin of mTHP memory into appropriately-sized folios, rather than into
single-page folios.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZu1BBwAKCRDdBJ7gKXxA
jlWNAQDYlqQLun7bgsAN4sSvi27VUuWv1q70jlMXTfmjJAvQqwD/fBFVR6IOOiw7
AkDbKWP2k0hWPiNJBGwoqxdHHx09Xgo=
=s0T+
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2024-09-20-02-31' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
"Along with the usual shower of singleton patches, notable patch series
in this pull request are:
- "Align kvrealloc() with krealloc()" from Danilo Krummrich. Adds
consistency to the APIs and behaviour of these two core allocation
functions. This also simplifies/enables Rustification.
- "Some cleanups for shmem" from Baolin Wang. No functional changes -
mode code reuse, better function naming, logic simplifications.
- "mm: some small page fault cleanups" from Josef Bacik. No
functional changes - code cleanups only.
- "Various memory tiering fixes" from Zi Yan. A small fix and a
little cleanup.
- "mm/swap: remove boilerplate" from Yu Zhao. Code cleanups and
simplifications and .text shrinkage.
- "Kernel stack usage histogram" from Pasha Tatashin and Shakeel
Butt. This is a feature, it adds new feilds to /proc/vmstat such as
$ grep kstack /proc/vmstat
kstack_1k 3
kstack_2k 188
kstack_4k 11391
kstack_8k 243
kstack_16k 0
which tells us that 11391 processes used 4k of stack while none at
all used 16k. Useful for some system tuning things, but
partivularly useful for "the dynamic kernel stack project".
- "kmemleak: support for percpu memory leak detect" from Pavel
Tikhomirov. Teaches kmemleak to detect leaksage of percpu memory.
- "mm: memcg: page counters optimizations" from Roman Gushchin. "3
independent small optimizations of page counters".
- "mm: split PTE/PMD PT table Kconfig cleanups+clarifications" from
David Hildenbrand. Improves PTE/PMD splitlock detection, makes
powerpc/8xx work correctly by design rather than by accident.
- "mm: remove arch_make_page_accessible()" from David Hildenbrand.
Some folio conversions which make arch_make_page_accessible()
unneeded.
- "mm, memcg: cg2 memory{.swap,}.peak write handlers" fro David
Finkel. Cleans up and fixes our handling of the resetting of the
cgroup/process peak-memory-use detector.
- "Make core VMA operations internal and testable" from Lorenzo
Stoakes. Rationalizaion and encapsulation of the VMA manipulation
APIs. With a view to better enable testing of the VMA functions,
even from a userspace-only harness.
- "mm: zswap: fixes for global shrinker" from Takero Funaki. Fix
issues in the zswap global shrinker, resulting in improved
performance.
- "mm: print the promo watermark in zoneinfo" from Kaiyang Zhao. Fill
in some missing info in /proc/zoneinfo.
- "mm: replace follow_page() by folio_walk" from David Hildenbrand.
Code cleanups and rationalizations (conversion to folio_walk())
resulting in the removal of follow_page().
- "improving dynamic zswap shrinker protection scheme" from Nhat
Pham. Some tuning to improve zswap's dynamic shrinker. Significant
reductions in swapin and improvements in performance are shown.
- "mm: Fix several issues with unaccepted memory" from Kirill
Shutemov. Improvements to the new unaccepted memory feature,
- "mm/mprotect: Fix dax puds" from Peter Xu. Implements mprotect on
DAX PUDs. This was missing, although nobody seems to have notied
yet.
- "Introduce a store type enum for the Maple tree" from Sidhartha
Kumar. Cleanups and modest performance improvements for the maple
tree library code.
- "memcg: further decouple v1 code from v2" from Shakeel Butt. Move
more cgroup v1 remnants away from the v2 memcg code.
- "memcg: initiate deprecation of v1 features" from Shakeel Butt.
Adds various warnings telling users that memcg v1 features are
deprecated.
- "mm: swap: mTHP swap allocator base on swap cluster order" from
Chris Li. Greatly improves the success rate of the mTHP swap
allocation.
- "mm: introduce numa_memblks" from Mike Rapoport. Moves various
disparate per-arch implementations of numa_memblk code into generic
code.
- "mm: batch free swaps for zap_pte_range()" from Barry Song. Greatly
improves the performance of munmap() of swap-filled ptes.
- "support large folio swap-out and swap-in for shmem" from Baolin
Wang. With this series we no longer split shmem large folios into
simgle-page folios when swapping out shmem.
- "mm/hugetlb: alloc/free gigantic folios" from Yu Zhao. Nice
performance improvements and code reductions for gigantic folios.
- "support shmem mTHP collapse" from Baolin Wang. Adds support for
khugepaged's collapsing of shmem mTHP folios.
- "mm: Optimize mseal checks" from Pedro Falcato. Fixes an mprotect()
performance regression due to the addition of mseal().
- "Increase the number of bits available in page_type" from Matthew
Wilcox. Increases the number of bits available in page_type!
- "Simplify the page flags a little" from Matthew Wilcox. Many legacy
page flags are now folio flags, so the page-based flags and their
accessors/mutators can be removed.
- "mm: store zero pages to be swapped out in a bitmap" from Usama
Arif. An optimization which permits us to avoid writing/reading
zero-filled zswap pages to backing store.
- "Avoid MAP_FIXED gap exposure" from Liam Howlett. Fixes a race
window which occurs when a MAP_FIXED operqtion is occurring during
an unrelated vma tree walk.
- "mm: remove vma_merge()" from Lorenzo Stoakes. Major rotorooting of
the vma_merge() functionality, making ot cleaner, more testable and
better tested.
- "misc fixups for DAMON {self,kunit} tests" from SeongJae Park.
Minor fixups of DAMON selftests and kunit tests.
- "mm: memory_hotplug: improve do_migrate_range()" from Kefeng Wang.
Code cleanups and folio conversions.
- "Shmem mTHP controls and stats improvements" from Ryan Roberts.
Cleanups for shmem controls and stats.
- "mm: count the number of anonymous THPs per size" from Barry Song.
Expose additional anon THP stats to userspace for improved tuning.
- "mm: finish isolate/putback_lru_page()" from Kefeng Wang: more
folio conversions and removal of now-unused page-based APIs.
- "replace per-quota region priorities histogram buffer with
per-context one" from SeongJae Park. DAMON histogram
rationalization.
- "Docs/damon: update GitHub repo URLs and maintainer-profile" from
SeongJae Park. DAMON documentation updates.
- "mm/vdpa: correct misuse of non-direct-reclaim __GFP_NOFAIL and
improve related doc and warn" from Jason Wang: fixes usage of page
allocator __GFP_NOFAIL and GFP_ATOMIC flags.
- "mm: split underused THPs" from Yu Zhao. Improve THP=always policy.
This was overprovisioning THPs in sparsely accessed memory areas.
- "zram: introduce custom comp backends API" frm Sergey Senozhatsky.
Add support for zram run-time compression algorithm tuning.
- "mm: Care about shadow stack guard gap when getting an unmapped
area" from Mark Brown. Fix up the various arch_get_unmapped_area()
implementations to better respect guard areas.
- "Improve mem_cgroup_iter()" from Kinsey Ho. Improve the reliability
of mem_cgroup_iter() and various code cleanups.
- "mm: Support huge pfnmaps" from Peter Xu. Extends the usage of huge
pfnmap support.
- "resource: Fix region_intersects() vs add_memory_driver_managed()"
from Huang Ying. Fix a bug in region_intersects() for systems with
CXL memory.
- "mm: hwpoison: two more poison recovery" from Kefeng Wang. Teaches
a couple more code paths to correctly recover from the encountering
of poisoned memry.
- "mm: enable large folios swap-in support" from Barry Song. Support
the swapin of mTHP memory into appropriately-sized folios, rather
than into single-page folios"
* tag 'mm-stable-2024-09-20-02-31' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (416 commits)
zram: free secondary algorithms names
uprobes: turn xol_area->pages[2] into xol_area->page
uprobes: introduce the global struct vm_special_mapping xol_mapping
Revert "uprobes: use vm_special_mapping close() functionality"
mm: support large folios swap-in for sync io devices
mm: add nr argument in mem_cgroup_swapin_uncharge_swap() helper to support large folios
mm: fix swap_read_folio_zeromap() for large folios with partial zeromap
mm/debug_vm_pgtable: Use pxdp_get() for accessing page table entries
set_memory: add __must_check to generic stubs
mm/vma: return the exact errno in vms_gather_munmap_vmas()
memcg: cleanup with !CONFIG_MEMCG_V1
mm/show_mem.c: report alloc tags in human readable units
mm: support poison recovery from copy_present_page()
mm: support poison recovery from do_cow_fault()
resource, kunit: add test case for region_intersects()
resource: make alloc_free_mem_region() works for iomem_resource
mm: z3fold: deprecate CONFIG_Z3FOLD
vfio/pci: implement huge_fault support
mm/arm64: support large pfn mappings
mm/x86: support large pfn mappings
...
The violation of atomicity occurs when the drbd_uuid_set_bm function is
executed simultaneously with modifying the value of
device->ldev->md.uuid[UI_BITMAP]. Consider a scenario where, while
device->ldev->md.uuid[UI_BITMAP] passes the validity check when its
value is not zero, the value of device->ldev->md.uuid[UI_BITMAP] is
written to zero. In this case, the check in drbd_uuid_set_bm might refer
to the old value of device->ldev->md.uuid[UI_BITMAP] (before locking),
which allows an invalid value to pass the validity check, resulting in
inconsistency.
To address this issue, it is recommended to include the data validity
check within the locked section of the function. This modification
ensures that the value of device->ldev->md.uuid[UI_BITMAP] does not
change during the validation process, thereby maintaining its integrity.
This possible bug is found by an experimental static analysis tool
developed by our team. This tool analyzes the locking APIs to extract
function pairs that can be concurrently executed, and then analyzes the
instructions in the paired functions to identify possible concurrency
bugs including data races and atomicity violations.
Fixes: 9f2247bb9b ("drbd: Protect accesses to the uuid set with a spinlock")
Cc: stable@vger.kernel.org
Signed-off-by: Qiu-ji Chen <chenqiuji666@gmail.com>
Reviewed-by: Philipp Reisner <philipp.reisner@linbit.com>
Link: https://lore.kernel.org/r/20240913083504.10549-1-chenqiuji666@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmbm9fQeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGXcwH/A8+IXnrGv+VzYgD
+mE4hgGGHt4dClcUZ31gQetkkT6xktEVp6pB6JkFO7oEgBiTkJBbYGl6VZtsAIOd
Fi3jic8ik0uhZLFcxDJcHTceh6Pw8bkhWoh0tkF3bkDRwbppJdG7Khyk8DxTl24w
ldqh9om2cC7w9IPVx93xTgKgMMZ63qiJyUdTvxEZI3BG8F70smlgZSPskLp2Iktd
FIJZPcyKM0bhJYwZOpXK0vx5C2cA4oIW4xriHUw4aklv646OBxNKevB2JJAft2uA
6LyvuLgnYn/OpdFGZ8slvdmhm6hLWft5B1/bWKorUkz7p5YGiySFzpkMVAkNJ6mS
cRwHJNc=
=flw3
-----END PGP SIGNATURE-----
Merge tag 'v6.11' into for-6.12/block
Merge in 6.11 final to get the fix for preventing deadlocks on an
elevator switch, as there's a fixup for that patch.
* tag 'v6.11': (1788 commits)
Linux 6.11
Revert "KVM: VMX: Always honor guest PAT on CPUs that support self-snoop"
pinctrl: pinctrl-cy8c95x0: Fix regcache
cifs: Fix signature miscalculation
mm: avoid leaving partial pfn mappings around in error case
drm/xe/client: add missing bo locking in show_meminfo()
drm/xe/client: fix deadlock in show_meminfo()
drm/xe/oa: Enable Xe2+ PES disaggregation
drm/xe/display: fix compat IS_DISPLAY_STEP() range end
drm/xe: Fix access_ok check in user_fence_create
drm/xe: Fix possible UAF in guc_exec_queue_process_msg
drm/xe: Remove fence check from send_tlb_invalidation
drm/xe/gt: Remove double include
net: netfilter: move nf flowtable bpf initialization in nf_flow_table_module_init()
PCI: Fix potential deadlock in pcim_intx()
workqueue: Clear worker->pool in the worker thread context
net: tighten bad gso csum offset check in virtio_net_hdr
netlink: specs: mptcp: fix port endianness
net: dpaa: Pad packets to ETH_ZLEN
mptcp: pm: Fix uaf in __timer_delete_sync
...
-----BEGIN PGP SIGNATURE-----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=uuLl
-----END PGP SIGNATURE-----
Merge tag 'for-6.12/block-20240913' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- MD changes via Song:
- md-bitmap refactoring (Yu Kuai)
- raid5 performance optimization (Artur Paszkiewicz)
- Other small fixes (Yu Kuai, Chen Ni)
- Add a sysfs entry 'new_level' (Xiao Ni)
- Improve information reported in /proc/mdstat (Mateusz Kusiak)
- NVMe changes via Keith:
- Asynchronous namespace scanning (Stuart)
- TCP TLS updates (Hannes)
- RDMA queue controller validation (Niklas)
- Align field names to the spec (Anuj)
- Metadata support validation (Puranjay)
- A syntax cleanup (Shen)
- Fix a Kconfig linking error (Arnd)
- New queue-depth quirk (Keith)
- Add missing unplug trace event (Keith)
- blk-iocost fixes (Colin, Konstantin)
- t10-pi modular removal and fixes (Alexey)
- Fix for potential BLKSECDISCARD overflow (Alexey)
- bio splitting cleanups and fixes (Christoph)
- Deal with folios rather than rather than pages, speeding up how the
block layer handles bigger IOs (Kundan)
- Use spinlocks rather than bit spinlocks in zram (Sebastian, Mike)
- Reduce zoned device overhead in ublk (Ming)
- Add and use sendpages_ok() for drbd and nvme-tcp (Ofir)
- Fix regression in partition error pointer checking (Riyan)
- Add support for write zeroes and rotational status in nbd (Wouter)
- Add Yu Kuai as new BFQ maintainer. The scheduler has been
unmaintained for quite a while.
- Various sets of fixes for BFQ (Yu Kuai)
- Misc fixes and cleanups (Alvaro, Christophe, Li, Md Haris, Mikhail,
Yang)
* tag 'for-6.12/block-20240913' of git://git.kernel.dk/linux: (120 commits)
nvme-pci: qdepth 1 quirk
block: fix potential invalid pointer dereference in blk_add_partition
blk_iocost: make read-only static array vrate_adj_pct const
block: unpin user pages belonging to a folio at once
mm: release number of pages of a folio
block: introduce folio awareness and add a bigger size from folio
block: Added folio-ized version of bio_add_hw_page()
block, bfq: factor out a helper to split bfqq in bfq_init_rq()
block, bfq: remove local variable 'bfqq_already_existing' in bfq_init_rq()
block, bfq: remove local variable 'split' in bfq_init_rq()
block, bfq: remove bfq_log_bfqg()
block, bfq: merge bfq_release_process_ref() into bfq_put_cooperator()
block, bfq: fix procress reference leakage for bfqq in merge chain
block, bfq: fix uaf for accessing waker_bfqq after splitting
blk-throttle: support prioritized processing of metadata
blk-throttle: remove last_low_overflow_time
drbd: Add NULL check for net_conf to prevent dereference in state validation
nvme-tcp: fix link failure for TCP auth
blk-mq: add missing unplug trace event
mtip32xx: Remove redundant null pointer checks in mtip_hw_debugfs_init()
...
If the net_conf pointer is NULL and the code attempts to access its
fields without a check, it will lead to a null pointer dereference.
Add a NULL check before dereferencing the pointer.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 44ed167da7 ("drbd: rcu_read_lock() and rcu_dereference() for tconn->net_conf")
Cc: stable@vger.kernel.org
Signed-off-by: Mikhail Lobanov <m.lobanov@rosalinux.ru>
Link: https://lore.kernel.org/r/20240909133740.84297-1-m.lobanov@rosalinux.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>
recompress device attribute supports alg=NAME parameter so that we can
specify only one particular algorithm we want to perform recompression
with. However, with algo params we now can have several exactly same
secondary algorithms but each with its own params tuning (e.g. priority 1
configured to use more aggressive level, and priority 2 configured to use
a pre-trained dictionary). Support priority=NUM parameter so that we can
correctly determine which secondary algorithm we want to use.
Link: https://lkml.kernel.org/r/20240902105656.1383858-25-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Support pre-trained dictionary param. Just like lz4, lz4hc doesn't
mandate specific format of the dictionary and zstd --train can be used to
train a dictionary for lz4, according to [1].
TEST
====
*** lz4hc
/sys/block/zram0/mm_stat
1750638592 608954620 621031424 0 621031424 1 0 34288 34288
*** lz4hc dict=/etc/lz4-dict-amd64
/sys/block/zram0/mm_stat
1750671360 505068582 514994176 0 514994176 1 0 34278 34278
[1] https://github.com/lz4/lz4/issues/557
Link: https://lkml.kernel.org/r/20240902105656.1383858-22-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Support pre-trained dictionary param. lz4 doesn't mandate specific format
of the dictionary and even zstd --train can be used to train a dictionary
for lz4, according to [1].
TEST
====
*** lz4
/sys/block/zram0/mm_stat
1750654976 664188565 676864000 0 676864000 1 0 34288 34288
*** lz4 dict=/etc/lz4-dict-amd64
/sys/block/zram0/mm_stat
1750638592 619891141 632053760 0 632053760 1 0 34278 34278
*** lz4 level=5 dict=/etc/lz4-dict-amd64
/sys/block/zram0/mm_stat
1750638592 727174243 740810752 0 740810752 1 0 34437 34437
[1] https://github.com/lz4/lz4/issues/557
Link: https://lkml.kernel.org/r/20240902105656.1383858-21-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Immutable params never change once comp has been allocated and setup, so
we don't need to store multiple copies of them in each per-CPU backend
context. Move those to per-comp zcomp_params and pass it to backends
callbacks for requests execution. Basically, this means parameters
sharing between different contexts.
Also introduce two new backends callbacks: setup_params() and
release_params(). First, we need to validate params in a driver-specific
way; second, driver may want to allocate its specific representation of
the params which is needed to execute requests.
Link: https://lkml.kernel.org/r/20240902105656.1383858-20-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Keep run-time driver data (scratch buffers, etc.) in zcomp_ctx structure.
This structure is allocated per-CPU because drivers (backends) need to
modify its content during requests execution.
We will split mutable and immutable driver data, this is a preparation
path.
Link: https://lkml.kernel.org/r/20240902105656.1383858-19-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Encapsulate compression/decompression data in zcomp_req structure.
Link: https://lkml.kernel.org/r/20240902105656.1383858-18-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Handle dict=path algorithm param so that we can read a pre-trained
compression algorithm dictionary which we then pass to the backend
configuration.
Link: https://lkml.kernel.org/r/20240902105656.1383858-17-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This attribute is used to setup compression algorithms' parameters, so we
can tweak algorithms' characteristics. At this point only 'level' is
supported (to be extended in the future).
Each call sets up parameters for one particular algorithm, which should be
specified either by the algorithm's priority or algo name. This is
expected to be called after corresponding algorithm is selected via
comp_algorithm or recomp_algorithm.
echo "priority=0 level=1" > /sys/block/zram0/algorithm_params
or
echo "algo=zstd level=1" > /sys/block/zram0/algorithm_params
Link: https://lkml.kernel.org/r/20240902105656.1383858-16-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
zstd compression params depends on level, but are constant for a given
instance of zstd compression backend. Calculate once (during ctx
creation).
Link: https://lkml.kernel.org/r/20240902105656.1383858-15-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We will store a per-algorithm parameters there (compression level,
dictionary, dictionary size, etc.).
Link: https://lkml.kernel.org/r/20240902105656.1383858-14-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Make sure that backends array has anything apart from the sentinel NULL
value.
We also select LZO_BACKEND if none backends were selected.
Link: https://lkml.kernel.org/r/20240902105656.1383858-13-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
zram works with PAGE_SIZE buffers, so we always know exact size of the
source buffer and hence can pass estimated_src_size to zstd_get_params().
This hint on x86_64, for example, reduces the size of the work memory
buffer from 1303520 bytes down to 90080 bytes. Given that compression
streams are per-CPU that's quite some memory saving.
Link: https://lkml.kernel.org/r/20240902105656.1383858-10-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Moving to custom backends implementation gives us ability to have our own
minimalistic and extendable API, and algorithms tunings becomes possible.
The list of compression backends is empty at this point, we will add
backends in the followup patches.
Link: https://lkml.kernel.org/r/20240902105656.1383858-5-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Since the debugfs_create_dir() never returns a null pointer, checking
the return value for a null pointer is redundant. Since
debugfs_create_file() can deal with a ERR_PTR() style pointer, drop
the check. Since mtip_hw_debugfs_init does not pay attention to the
return value, its return type can be changed to void.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20240907034046.3595268-1-lizetao1@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=BwIz
-----END PGP SIGNATURE-----
Merge tag 'block-6.11-20240906' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
"Mostly just some fixlets for NVMe, but also a bug fix for the ublk
driver and an integrity fix"
* tag 'block-6.11-20240906' of git://git.kernel.dk/linux:
bio-integrity: don't restrict the size of integrity metadata
ublk_drv: fix NULL pointer dereference in ublk_ctrl_start_recovery()
nvmet: Identify-Active Namespace ID List command should reject invalid nsid
nvme: set BLK_FEAT_ZONED for ZNS multipath disks
nvme-pci: Add sleep quirk for Samsung 990 Evo
nvme-pci: allocate tagset on reset if necessary
nvmet-tcp: fix kernel crash if commands allocation fails
nvme: use better description for async reset reason
nvmet: Make nvmet_debugfs static
The zram_table_entry::flags member is of type long and uses 8 bytes on a
64bit architecture. With a PAGE_SIZE of 256KiB we have PAGE_SHIFT of 18
which in turn leads to __NR_ZRAM_PAGEFLAGS = 27. This still fits in an
ordinary integer.
By reducing the size of `flags' to four bytes, the size of the struct
goes back to 16 bytes. The padding between the lock and ac_time (if
enabled) is also gone.
Make zram_table_entry::flags an unsigned int and update the build test
to reflect the change.
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/20240906141520.730009-4-bigeasy@linutronix.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The ZRAM_LOCK was used for locking and after the addition of spinlock_t
the bit set and cleared but there no reader of it.
Remove the ZRAM_LOCK bit.
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/20240906141520.730009-3-bigeasy@linutronix.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The bit spinlock disables preemption. The spinlock_t lock becomes a sleeping
lock on PREEMPT_RT and it can not be acquired in this context. In this locked
section, zs_free() acquires a zs_pool::lock, and there is access to
zram::wb_limit_lock.
Add a spinlock_t for locking. Keep the set/ clear ZRAM_LOCK bit after
the lock has been acquired/ dropped. The size of struct zram_table_entry
increases by 4 bytes due to lock and additional 4 bytes padding with
CONFIG_ZRAM_TRACK_ENTRY_ACTIME enabled.
Signed-off-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/20240906141520.730009-2-bigeasy@linutronix.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The version of the NBD protocol implemented by the kernel driver
currently has a 32 bit field for length values. As the NBD protocol uses
bytes as a unit of length, length values larger than 2^32 bytes cannot
be expressed.
Update the max_hw_discard_sectors field to match that.
Signed-off-by: Wouter Verhelst <w@uter.be>
Fixes: 268283244c ("nbd: use the atomic queue limits API in nbd_set_size")
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: Eric Blake <eblake@redhat.Com>
Link: https://lore.kernel.org/r/20240812133032.115134-8-w@uter.be
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The NBD protocol defines a message for zeroing out a region of an export
Add support to the kernel driver for that message.
Signed-off-by: Wouter Verhelst <w@uter.be>
Cc: Eric Blake <eblake@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240812133032.115134-3-w@uter.be
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When two UBLK_CMD_START_USER_RECOVERY commands are submitted, the
first one sets 'ubq->ubq_daemon' to NULL, and the second one triggers
WARN in ublk_queue_reinit() and subsequently a NULL pointer dereference
issue.
Fix it by adding the check in ublk_ctrl_start_recovery() and return
immediately in case of zero 'ub->nr_queues_ready'.
BUG: kernel NULL pointer dereference, address: 0000000000000028
RIP: 0010:ublk_ctrl_start_recovery.constprop.0+0x82/0x180
Call Trace:
<TASK>
? __die+0x20/0x70
? page_fault_oops+0x75/0x170
? exc_page_fault+0x64/0x140
? asm_exc_page_fault+0x22/0x30
? ublk_ctrl_start_recovery.constprop.0+0x82/0x180
ublk_ctrl_uring_cmd+0x4f7/0x6c0
? pick_next_task_idle+0x26/0x40
io_uring_cmd+0x9a/0x1b0
io_issue_sqe+0x193/0x3f0
io_wq_submit_work+0x9b/0x390
io_worker_handle_work+0x165/0x360
io_wq_worker+0xcb/0x2f0
? finish_task_switch.isra.0+0x203/0x290
? finish_task_switch.isra.0+0x203/0x290
? __pfx_io_wq_worker+0x10/0x10
ret_from_fork+0x2d/0x50
? __pfx_io_wq_worker+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
Fixes: c732a852b4 ("ublk_drv: add START_USER_RECOVERY and END_USER_RECOVERY support")
Reported-and-tested-by: Changhui Zhong <czhong@redhat.com>
Closes: https://lore.kernel.org/all/CAGVVp+UvLiS+bhNXV-h2icwX1dyybbYHeQUuH7RYqUvMQf6N3w@mail.gmail.com
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Li Nan <linan122@huawei.com>
Link: https://lore.kernel.org/r/20240904031348.4139545-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that we have an extra 8 bits, we don't need to limit ourselves to
supporting a 64KiB page size. I'm sure both Hexagon users are grateful,
but it does reduce complexity a little. We can also remove
reset_first_obj_offset() as calling __ClearPageZsmalloc() will now reset
all 32 bits of page_type.
Link: https://lkml.kernel.org/r/20240821173914.2270383-5-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
If request timetout is handled by nbd_requeue_cmd(), normal completion
has to be stopped for avoiding to complete this requeued request, other
use-after-free can be triggered.
Fix the race by clearing NBD_CMD_INFLIGHT in nbd_requeue_cmd(), meantime
make sure that cmd->lock is grabbed for clearing the flag and the
requeue.
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Yu Kuai <yukuai3@huawei.com>
Fixes: 2895f1831e ("nbd: don't clear 'NBD_CMD_INFLIGHT' flag if request is not completed")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20240830034145.1827742-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The bio->bi_iter.bi_size is updated when bio_add_page() is called. So we
do not need to assign msg->bi_size again to it, since its redudant and
can also be harmful. Instead we can use it to add a sanity check, which
checks the locally calculated bi_size, with the one sent in msg.
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com>
Link: https://lore.kernel.org/r/20240809135346.978320-1-haris.iqbal@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove the debugfs_create_dir() error check. It's safe to pass in error
pointers to the debugfs API, hence the user isn't supposed to include
error checking of the return values.
Signed-off-by: Yang Ruibin <11162571@vivo.com>
Link: https://lore.kernel.org/r/20240827022741.3410294-1-11162571@vivo.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ublk zoned takes 16 bytes in each request pdu just for handling REPORT_ZONE
operation, this way does waste memory since request pdu is allocated
statically.
Store the transient zone report data into one global xarray, and remove
it after the report zone request is completed. This way is reasonable
since report zone is run in slow code path.
Fixes: 29802d7ca3 ("ublk: enable zoned storage support")
Cc: Damien Le Moal <dlemoal@kernel.org>
Cc: Andreas Hindborg <a.hindborg@samsung.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240812013624.587587-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit b411b3637f ("The DRBD driver") declared but never implemented
drbd_read_remote(), is_valid_ar_handle() and drbd_set_recv_tcq().
And commit 668700b40a ("drbd: Create a dedicated workqueue for sending acks on the control connection")
never implemented drbd_send_ping_wf().
Commit 2451fc3b2b ("drbd: Removed the BIO_RW_BARRIER support form the receiver/epoch code")
leave w_e_reissue() declaration unused.
Commit 8fe605513a ("drbd: Rename drbdd_init() -> drbd_receiver()")
rename drbdd_init() and leave unsued declaration. Also drbd_asender() is removed in
commit 1c03e52083 ("drbd: Rename asender to ack_receiver").
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20240802095147.2788218-1-yuehaibing@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The NBD protocol defines the flag NBD_FLAG_ROTATIONAL to flag that the
export in use should be treated as a rotational device.
Add support for that flag to the kernel driver.
Signed-off-by: Wouter Verhelst <w@uter.be>
Reviewed-by: Eric Blake <eblake@redhat.com>
Link: https://lore.kernel.org/r/20240725164536.1275851-1-w@uter.be
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently _drbd_send_page() use sendpage_ok() in order to enable
MSG_SPLICE_PAGES, it check the first page of the iterator, the iterator
may represent contiguous pages.
MSG_SPLICE_PAGES enables skb_splice_from_iter() which checks all the
pages it sends with sendpage_ok().
When _drbd_send_page() sends an iterator that the first page is
sendable, but one of the other pages isn't skb_splice_from_iter() warns
and aborts the data transfer.
Using the new helper sendpages_ok() in order to enable MSG_SPLICE_PAGES
solves the issue.
Acked-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Signed-off-by: Ofir Gal <ofir.gal@volumez.com>
Link: https://lore.kernel.org/r/20240718084515.3833733-4-ofir.gal@volumez.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=Ci8Z
-----END PGP SIGNATURE-----
Merge tag 'block-6.11-20240726' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- Fix request without payloads cleanup (Leon)
- Use new protection information format (Francis)
- Improved debug message for lost pci link (Bart)
- Another apst quirk (Wang)
- Use appropriate sysfs api for printing chars (Markus)
- ublk async device deletion fix (Ming)
- drbd kerneldoc fixups (Simon)
- Fix deadlock between sd removal and release (Yang)
* tag 'block-6.11-20240726' of git://git.kernel.dk/linux:
nvme-pci: add missing condition check for existence of mapped data
ublk: fix UBLK_CMD_DEL_DEV_ASYNC handling
block: fix deadlock between sd_remove & sd_release
drbd: Add peer_device to Kernel doc
nvme-core: choose PIF from QPIF if QPIFS supports and PIF is QTYPE
nvme-pci: Fix the instructions for disabling power management
nvme: remove redundant bdev local variable
nvme-fabrics: Use seq_putc() in __nvmf_concat_opt_tokens()
nvme/pci: Add APST quirk for Lenovo N60z laptop
assertion failure in the face of watch errors with -o exclusive
mappings in RBD marked for stable and some assorted CephFS fixes.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmajtIUTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi1fwB/4/CsFZLQC+ybWSqoZVYD01qND0muol
44Nr6NyKdW302jQhAXchecB6s6L+N0azhVlAKKB8sO9XCifKA8RzuW75Y0+8z78B
pgB6K7ZOzAIuPIG9mmNbutUHEd24CzGXNA28lEQkrNT8D6UZTENXQRJb1dS2GzQ7
T2PyjFFoyF0z1bDZ85URHxeyMetEe/TzWUlG1P2QI98V+RP8nK+mGYmdXNGKhH87
Ltf2pxjsiomtoH4QRm4LX7vwOUY1Ljf4HpSS1p+c5Fova2UTtTDbVfTFbh+ZjuQV
hlh1ypNLM+igifu3nVeJ/Ga2f71zVFM66tnmpjcY3DxZAp70e1W2HMFD
=Zfcy
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-6.11-rc1' of https://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"A small patchset to address bogus I/O errors and ultimately an
assertion failure in the face of watch errors with -o exclusive
mappings in RBD marked for stable and some assorted CephFS fixes"
* tag 'ceph-for-6.11-rc1' of https://github.com/ceph/ceph-client:
rbd: don't assume rbd_is_lock_owner() for exclusive mappings
rbd: don't assume RBD_LOCK_STATE_LOCKED for exclusive mappings
rbd: rename RBD_LOCK_STATE_RELEASING and releasing_wait
ceph: fix incorrect kmalloc size of pagevec mempool
ceph: periodically flush the cap releases
ceph: convert comma to semicolon in __ceph_dentry_dir_lease_touch()
ceph: use cap_wait_list only if debugfs is enabled
Expanding on the previous commit, assuming that rbd_is_lock_owner()
always returns true (i.e. that we are either in RBD_LOCK_STATE_LOCKED
or RBD_LOCK_STATE_QUIESCING) if the mapping is exclusive is wrong too.
In case ceph_cls_set_cookie() fails, the lock would be temporarily
released even if the mapping is exclusive, meaning that we can end up
even in RBD_LOCK_STATE_UNLOCKED.
IOW, exclusive mappings are really "just" about disabling automatic
lock transitions (as documented in the man page), not about grabbing
the lock and holding on to it whatever it takes.
Cc: stable@vger.kernel.org
Fixes: 637cd06053 ("rbd: new exclusive lock wait/wake code")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
Every time a watch is reestablished after getting lost, we need to
update the cookie which involves quiescing exclusive lock. For this,
we transition from RBD_LOCK_STATE_LOCKED to RBD_LOCK_STATE_QUIESCING
roughly for the duration of rbd_reacquire_lock() call. If the mapping
is exclusive and I/O happens to arrive in this time window, it's failed
with EROFS (later translated to EIO) based on the wrong assumption in
rbd_img_exclusive_lock() -- "lock got released?" check there stopped
making sense with commit a2b1da0979 ("rbd: lock should be quiesced on
reacquire").
To make it worse, any such I/O is added to the acquiring list before
EROFS is returned and this sets up for violating rbd_lock_del_request()
precondition that the request is either on the running list or not on
any list at all -- see commit ded080c86b ("rbd: don't move requests
to the running list on errors"). rbd_lock_del_request() ends up
processing these requests as if they were on the running list which
screws up quiescing_wait completion counter and ultimately leads to
rbd_assert(!completion_done(&rbd_dev->quiescing_wait));
being triggered on the next watch error.
Cc: stable@vger.kernel.org # 06ef84c4e9c4: rbd: rename RBD_LOCK_STATE_RELEASING and releasing_wait
Cc: stable@vger.kernel.org
Fixes: 637cd06053 ("rbd: new exclusive lock wait/wake code")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
... to RBD_LOCK_STATE_QUIESCING and quiescing_wait to recognize that
this state and the associated completion are backing rbd_quiesce_lock(),
which isn't specific to releasing the lock.
While exclusive lock does get quiesced before it's released, it also
gets quiesced before an attempt to update the cookie is made and there
the lock is not released as long as ceph_cls_set_cookie() succeeds.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
In ublk_ctrl_uring_cmd(), ioctl command NR should be used for
matching _IOC_NR(cmd_op).
Fix it by adding one private macro, and this way is clean.
Fixes: 13fe8e6825 ("ublk: add UBLK_CMD_DEL_DEV_ASYNC")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240724143311.2646330-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add missing documentation of peer_device parameter to Kernel doc.
These parameters were added in commit 8164dd6c8a ("drbd: Add peer
device parameter to whole-bitmap I/O handlers")
Flagged by W=1 builds.
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240723-drbd-doc-v1-1-a04d9b7a9688@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
walkers") is known to cause a performance regression
(https://lore.kernel.org/all/3acefad9-96e5-4681-8014-827d6be71c7a@linux.ibm.com/T/#mfa809800a7862fb5bdf834c6f71a3a5113eb83ff).
Yu has a fix which I'll send along later via the hotfixes branch.
- In the series "mm: Avoid possible overflows in dirty throttling" Jan
Kara addresses a couple of issues in the writeback throttling code.
These fixes are also targetted at -stable kernels.
- Ryusuke Konishi's series "nilfs2: fix potential issues related to
reserved inodes" does that. This should actually be in the
mm-nonmm-stable tree, along with the many other nilfs2 patches. My bad.
- More folio conversions from Kefeng Wang in the series "mm: convert to
folio_alloc_mpol()"
- Kemeng Shi has sent some cleanups to the writeback code in the series
"Add helper functions to remove repeated code and improve readability of
cgroup writeback"
- Kairui Song has made the swap code a little smaller and a little
faster in the series "mm/swap: clean up and optimize swap cache index".
- In the series "mm/memory: cleanly support zeropage in
vm_insert_page*(), vm_map_pages*() and vmf_insert_mixed()" David
Hildenbrand has reworked the rather sketchy handling of the use of the
zeropage in MAP_SHARED mappings. I don't see any runtime effects here -
more a cleanup/understandability/maintainablity thing.
- Dev Jain has improved selftests/mm/va_high_addr_switch.c's handling of
higher addresses, for aarch64. The (poorly named) series is
"Restructure va_high_addr_switch".
- The core TLB handling code gets some cleanups and possible slight
optimizations in Bang Li's series "Add update_mmu_tlb_range() to
simplify code".
- Jane Chu has improved the handling of our
fake-an-unrecoverable-memory-error testing feature MADV_HWPOISON in the
series "Enhance soft hwpoison handling and injection".
- Jeff Johnson has sent a billion patches everywhere to add
MODULE_DESCRIPTION() to everything. Some landed in this pull.
- In the series "mm: cleanup MIGRATE_SYNC_NO_COPY mode", Kefeng Wang has
simplified migration's use of hardware-offload memory copying.
- Yosry Ahmed performs more folio API conversions in his series "mm:
zswap: trivial folio conversions".
- In the series "large folios swap-in: handle refault cases first",
Chuanhua Han inches us forward in the handling of large pages in the
swap code. This is a cleanup and optimization, working toward the end
objective of full support of large folio swapin/out.
- In the series "mm,swap: cleanup VMA based swap readahead window
calculation", Huang Ying has contributed some cleanups and a possible
fixlet to his VMA based swap readahead code.
- In the series "add mTHP support for anonymous shmem" Baolin Wang has
taught anonymous shmem mappings to use multisize THP. By default this
is a no-op - users must opt in vis sysfs controls. Dramatic
improvements in pagefault latency are realized.
- David Hildenbrand has some cleanups to our remaining use of
page_mapcount() in the series "fs/proc: move page_mapcount() to
fs/proc/internal.h".
- David also has some highmem accounting cleanups in the series
"mm/highmem: don't track highmem pages manually".
- Build-time fixes and cleanups from John Hubbard in the series
"cleanups, fixes, and progress towards avoiding "make headers"".
- Cleanups and consolidation of the core pagemap handling from Barry
Song in the series "mm: introduce pmd|pte_needs_soft_dirty_wp helpers
and utilize them".
- Lance Yang's series "Reclaim lazyfree THP without splitting" has
reduced the latency of the reclaim of pmd-mapped THPs under fairly
common circumstances. A 10x speedup is seen in a microbenchmark.
It does this by punting to aother CPU but I guess that's a win unless
all CPUs are pegged.
- hugetlb_cgroup cleanups from Xiu Jianfeng in the series
"mm/hugetlb_cgroup: rework on cftypes".
- Miaohe Lin's series "Some cleanups for memory-failure" does just that
thing.
- Is anyone reading this stuff? If so, email me!
- Someone other than SeongJae has developed a DAMON feature in Honggyu
Kim's series "DAMON based tiered memory management for CXL memory".
This adds DAMON features which may be used to help determine the
efficiency of our placement of CXL/PCIe attached DRAM.
- DAMON user API centralization and simplificatio work in SeongJae
Park's series "mm/damon: introduce DAMON parameters online commit
function".
- In the series "mm: page_type, zsmalloc and page_mapcount_reset()"
David Hildenbrand does some maintenance work on zsmalloc - partially
modernizing its use of pageframe fields.
- Kefeng Wang provides more folio conversions in the series "mm: remove
page_maybe_dma_pinned() and page_mkclean()".
- More cleanup from David Hildenbrand, this time in the series
"mm/memory_hotplug: use PageOffline() instead of PageReserved() for
!ZONE_DEVICE". It "enlightens memory hotplug more about PageOffline()
pages" and permits the removal of some virtio-mem hacks.
- Barry Song's series "mm: clarify folio_add_new_anon_rmap() and
__folio_add_anon_rmap()" is a cleanup to the anon folio handling in
preparation for mTHP (multisize THP) swapin.
- Kefeng Wang's series "mm: improve clear and copy user folio"
implements more folio conversions, this time in the area of large folio
userspace copying.
- The series "Docs/mm/damon/maintaier-profile: document a mailing tool
and community meetup series" tells people how to get better involved
with other DAMON developers. From SeongJae Park.
- A large series ("kmsan: Enable on s390") from Ilya Leoshkevich does
that.
- David Hildenbrand sends along more cleanups, this time against the
migration code. The series is "mm/migrate: move NUMA hinting fault
folio isolation + checks under PTL".
- Jan Kara has found quite a lot of strangenesses and minor errors in
the readahead code. He addresses this in the series "mm: Fix various
readahead quirks".
- SeongJae Park's series "selftests/damon: test DAMOS tried regions and
{min,max}_nr_regions" adds features and addresses errors in DAMON's self
testing code.
- Gavin Shan has found a userspace-triggerable WARN in the pagecache
code. The series "mm/filemap: Limit page cache size to that supported
by xarray" addresses this. The series is marked cc:stable.
- Chengming Zhou's series "mm/ksm: cmp_and_merge_page() optimizations
and cleanup" cleans up and slightly optimizes KSM.
- Roman Gushchin has separated the memcg-v1 and memcg-v2 code - lots of
code motion. The series (which also makes the memcg-v1 code
Kconfigurable) are
"mm: memcg: separate legacy cgroup v1 code and put under config
option" and
"mm: memcg: put cgroup v1-specific memcg data under CONFIG_MEMCG_V1"
- Dan Schatzberg's series "Add swappiness argument to memory.reclaim"
adds an additional feature to this cgroup-v2 control file.
- The series "Userspace controls soft-offline pages" from Jiaqi Yan
permits userspace to stop the kernel's automatic treatment of excessive
correctable memory errors. In order to permit userspace to monitor and
handle this situation.
- Kefeng Wang's series "mm: migrate: support poison recover from migrate
folio" teaches the kernel to appropriately handle migration from
poisoned source folios rather than simply panicing.
- SeongJae Park's series "Docs/damon: minor fixups and improvements"
does those things.
- In the series "mm/zsmalloc: change back to per-size_class lock"
Chengming Zhou improves zsmalloc's scalability and memory utilization.
- Vivek Kasireddy's series "mm/gup: Introduce memfd_pin_folios() for
pinning memfd folios" makes the GUP code use FOLL_PIN rather than bare
refcount increments. So these paes can first be moved aside if they
reside in the movable zone or a CMA block.
- Andrii Nakryiko has added a binary ioctl()-based API to /proc/pid/maps
for much faster reading of vma information. The series is "query VMAs
from /proc/<pid>/maps".
- In the series "mm: introduce per-order mTHP split counters" Lance Yang
improves the kernel's presentation of developer information related to
multisize THP splitting.
- Michael Ellerman has developed the series "Reimplement huge pages
without hugepd on powerpc (8xx, e500, book3s/64)". This permits
userspace to use all available huge page sizes.
- In the series "revert unconditional slab and page allocator fault
injection calls" Vlastimil Babka removes a performance-affecting and not
very useful feature from slab fault injection.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZp2C+QAKCRDdBJ7gKXxA
joTkAQDvjqOoFStqk4GU3OXMYB7WCU/ZQMFG0iuu1EEwTVDZ4QEA8CnG7seek1R3
xEoo+vw0sWWeLV3qzsxnCA1BJ8cTJA8=
=z0Lf
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2024-07-21-14-50' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- In the series "mm: Avoid possible overflows in dirty throttling" Jan
Kara addresses a couple of issues in the writeback throttling code.
These fixes are also targetted at -stable kernels.
- Ryusuke Konishi's series "nilfs2: fix potential issues related to
reserved inodes" does that. This should actually be in the
mm-nonmm-stable tree, along with the many other nilfs2 patches. My
bad.
- More folio conversions from Kefeng Wang in the series "mm: convert to
folio_alloc_mpol()"
- Kemeng Shi has sent some cleanups to the writeback code in the series
"Add helper functions to remove repeated code and improve readability
of cgroup writeback"
- Kairui Song has made the swap code a little smaller and a little
faster in the series "mm/swap: clean up and optimize swap cache
index".
- In the series "mm/memory: cleanly support zeropage in
vm_insert_page*(), vm_map_pages*() and vmf_insert_mixed()" David
Hildenbrand has reworked the rather sketchy handling of the use of
the zeropage in MAP_SHARED mappings. I don't see any runtime effects
here - more a cleanup/understandability/maintainablity thing.
- Dev Jain has improved selftests/mm/va_high_addr_switch.c's handling
of higher addresses, for aarch64. The (poorly named) series is
"Restructure va_high_addr_switch".
- The core TLB handling code gets some cleanups and possible slight
optimizations in Bang Li's series "Add update_mmu_tlb_range() to
simplify code".
- Jane Chu has improved the handling of our
fake-an-unrecoverable-memory-error testing feature MADV_HWPOISON in
the series "Enhance soft hwpoison handling and injection".
- Jeff Johnson has sent a billion patches everywhere to add
MODULE_DESCRIPTION() to everything. Some landed in this pull.
- In the series "mm: cleanup MIGRATE_SYNC_NO_COPY mode", Kefeng Wang
has simplified migration's use of hardware-offload memory copying.
- Yosry Ahmed performs more folio API conversions in his series "mm:
zswap: trivial folio conversions".
- In the series "large folios swap-in: handle refault cases first",
Chuanhua Han inches us forward in the handling of large pages in the
swap code. This is a cleanup and optimization, working toward the end
objective of full support of large folio swapin/out.
- In the series "mm,swap: cleanup VMA based swap readahead window
calculation", Huang Ying has contributed some cleanups and a possible
fixlet to his VMA based swap readahead code.
- In the series "add mTHP support for anonymous shmem" Baolin Wang has
taught anonymous shmem mappings to use multisize THP. By default this
is a no-op - users must opt in vis sysfs controls. Dramatic
improvements in pagefault latency are realized.
- David Hildenbrand has some cleanups to our remaining use of
page_mapcount() in the series "fs/proc: move page_mapcount() to
fs/proc/internal.h".
- David also has some highmem accounting cleanups in the series
"mm/highmem: don't track highmem pages manually".
- Build-time fixes and cleanups from John Hubbard in the series
"cleanups, fixes, and progress towards avoiding "make headers"".
- Cleanups and consolidation of the core pagemap handling from Barry
Song in the series "mm: introduce pmd|pte_needs_soft_dirty_wp helpers
and utilize them".
- Lance Yang's series "Reclaim lazyfree THP without splitting" has
reduced the latency of the reclaim of pmd-mapped THPs under fairly
common circumstances. A 10x speedup is seen in a microbenchmark.
It does this by punting to aother CPU but I guess that's a win unless
all CPUs are pegged.
- hugetlb_cgroup cleanups from Xiu Jianfeng in the series
"mm/hugetlb_cgroup: rework on cftypes".
- Miaohe Lin's series "Some cleanups for memory-failure" does just that
thing.
- Someone other than SeongJae has developed a DAMON feature in Honggyu
Kim's series "DAMON based tiered memory management for CXL memory".
This adds DAMON features which may be used to help determine the
efficiency of our placement of CXL/PCIe attached DRAM.
- DAMON user API centralization and simplificatio work in SeongJae
Park's series "mm/damon: introduce DAMON parameters online commit
function".
- In the series "mm: page_type, zsmalloc and page_mapcount_reset()"
David Hildenbrand does some maintenance work on zsmalloc - partially
modernizing its use of pageframe fields.
- Kefeng Wang provides more folio conversions in the series "mm: remove
page_maybe_dma_pinned() and page_mkclean()".
- More cleanup from David Hildenbrand, this time in the series
"mm/memory_hotplug: use PageOffline() instead of PageReserved() for
!ZONE_DEVICE". It "enlightens memory hotplug more about PageOffline()
pages" and permits the removal of some virtio-mem hacks.
- Barry Song's series "mm: clarify folio_add_new_anon_rmap() and
__folio_add_anon_rmap()" is a cleanup to the anon folio handling in
preparation for mTHP (multisize THP) swapin.
- Kefeng Wang's series "mm: improve clear and copy user folio"
implements more folio conversions, this time in the area of large
folio userspace copying.
- The series "Docs/mm/damon/maintaier-profile: document a mailing tool
and community meetup series" tells people how to get better involved
with other DAMON developers. From SeongJae Park.
- A large series ("kmsan: Enable on s390") from Ilya Leoshkevich does
that.
- David Hildenbrand sends along more cleanups, this time against the
migration code. The series is "mm/migrate: move NUMA hinting fault
folio isolation + checks under PTL".
- Jan Kara has found quite a lot of strangenesses and minor errors in
the readahead code. He addresses this in the series "mm: Fix various
readahead quirks".
- SeongJae Park's series "selftests/damon: test DAMOS tried regions and
{min,max}_nr_regions" adds features and addresses errors in DAMON's
self testing code.
- Gavin Shan has found a userspace-triggerable WARN in the pagecache
code. The series "mm/filemap: Limit page cache size to that supported
by xarray" addresses this. The series is marked cc:stable.
- Chengming Zhou's series "mm/ksm: cmp_and_merge_page() optimizations
and cleanup" cleans up and slightly optimizes KSM.
- Roman Gushchin has separated the memcg-v1 and memcg-v2 code - lots of
code motion. The series (which also makes the memcg-v1 code
Kconfigurable) are "mm: memcg: separate legacy cgroup v1 code and put
under config option" and "mm: memcg: put cgroup v1-specific memcg
data under CONFIG_MEMCG_V1"
- Dan Schatzberg's series "Add swappiness argument to memory.reclaim"
adds an additional feature to this cgroup-v2 control file.
- The series "Userspace controls soft-offline pages" from Jiaqi Yan
permits userspace to stop the kernel's automatic treatment of
excessive correctable memory errors. In order to permit userspace to
monitor and handle this situation.
- Kefeng Wang's series "mm: migrate: support poison recover from
migrate folio" teaches the kernel to appropriately handle migration
from poisoned source folios rather than simply panicing.
- SeongJae Park's series "Docs/damon: minor fixups and improvements"
does those things.
- In the series "mm/zsmalloc: change back to per-size_class lock"
Chengming Zhou improves zsmalloc's scalability and memory
utilization.
- Vivek Kasireddy's series "mm/gup: Introduce memfd_pin_folios() for
pinning memfd folios" makes the GUP code use FOLL_PIN rather than
bare refcount increments. So these paes can first be moved aside if
they reside in the movable zone or a CMA block.
- Andrii Nakryiko has added a binary ioctl()-based API to
/proc/pid/maps for much faster reading of vma information. The series
is "query VMAs from /proc/<pid>/maps".
- In the series "mm: introduce per-order mTHP split counters" Lance
Yang improves the kernel's presentation of developer information
related to multisize THP splitting.
- Michael Ellerman has developed the series "Reimplement huge pages
without hugepd on powerpc (8xx, e500, book3s/64)". This permits
userspace to use all available huge page sizes.
- In the series "revert unconditional slab and page allocator fault
injection calls" Vlastimil Babka removes a performance-affecting and
not very useful feature from slab fault injection.
* tag 'mm-stable-2024-07-21-14-50' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (411 commits)
mm/mglru: fix ineffective protection calculation
mm/zswap: fix a white space issue
mm/hugetlb: fix kernel NULL pointer dereference when migrating hugetlb folio
mm/hugetlb: fix possible recursive locking detected warning
mm/gup: clear the LRU flag of a page before adding to LRU batch
mm/numa_balancing: teach mpol_to_str about the balancing mode
mm: memcg1: convert charge move flags to unsigned long long
alloc_tag: fix page_ext_get/page_ext_put sequence during page splitting
lib: reuse page_ext_data() to obtain codetag_ref
lib: add missing newline character in the warning message
mm/mglru: fix overshooting shrinker memory
mm/mglru: fix div-by-zero in vmpressure_calc_level()
mm/kmemleak: replace strncpy() with strscpy()
mm, page_alloc: put should_fail_alloc_page() back behing CONFIG_FAIL_PAGE_ALLOC
mm, slab: put should_failslab() back behind CONFIG_SHOULD_FAILSLAB
mm: ignore data-race in __swap_writepage
hugetlbfs: ensure generic_hugetlb_get_unmapped_area() returns higher address than mmap_min_addr
mm: shmem: rename mTHP shmem counters
mm: swap_state: use folio_alloc_mpol() in __read_swap_cache_async()
mm/migrate: putback split folios when numa hint migration fails
...
Several new features here:
- Virtio find vqs API has been reworked
(required to fix the scalability issue we have with
adminq, which I hope to merge later in the cycle)
- vDPA driver for Marvell OCTEON
- virtio fs performance improvement
- mlx5 migration speedups
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmaXjQQPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpnIsH/jVNqAQbe/vaBQdNMdnsA+P9A9unLbYRxYCQ
tN73mQRIXKtnZHBRAEbMGq52HPYg8HlN2HJSgyNo6I6t8VD+PiOco7m+3GpmqEcW
aXPOPl0BAbVoDgyutxRuuodP8Z61lBx0mG6iOxpzTXOPGlpQqtPCFHO8YnodqnPf
tMix/5uAqgZKV2siCbw5DtzwEc0gDHU8qsD0/nyoS5nBDF9yh/ardr5P/qiyFDQH
atCNYTOhIFU83pLAaw0fpCGbkt7gxf+5RpWVx3wkYww+/MwvYhsveRvQyaGbBz3n
WDtET3SOtVTta98OAGIKCq/2z8f6mYXBP7vXapBgnJG3vwS/poQ=
=LYua
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"Several new features here:
- Virtio find vqs API has been reworked (required to fix the
scalability issue we have with adminq, which I hope to merge later
in the cycle)
- vDPA driver for Marvell OCTEON
- virtio fs performance improvement
- mlx5 migration speedups
Fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (56 commits)
virtio: rename virtio_find_vqs_info() to virtio_find_vqs()
virtio: remove unused virtio_find_vqs() and virtio_find_vqs_ctx() helpers
virtio: convert the rest virtio_find_vqs() users to virtio_find_vqs_info()
virtio_balloon: convert to use virtio_find_vqs_info()
virtiofs: convert to use virtio_find_vqs_info()
scsi: virtio_scsi: convert to use virtio_find_vqs_info()
virtio_net: convert to use virtio_find_vqs_info()
virtio_crypto: convert to use virtio_find_vqs_info()
virtio_console: convert to use virtio_find_vqs_info()
virtio_blk: convert to use virtio_find_vqs_info()
virtio: rename find_vqs_info() op to find_vqs()
virtio: remove the original find_vqs() op
virtio: call virtio_find_vqs_info() from virtio_find_single_vq() directly
virtio: convert find_vqs() op implementations to find_vqs_info()
virtio_pci: convert vp_*find_vqs() ops to find_vqs_info()
virtio: introduce virtio_queue_info struct and find_vqs_info() config op
virtio: make virtio_find_single_vq() call virtio_find_vqs()
virtio: make virtio_find_vqs() call virtio_find_vqs_ctx()
caif_virtio: use virtio_find_single_vq() for single virtqueue finding
vdpa/mlx5: Don't enable non-active VQs in .set_vq_ready()
...
Since the original virtio_find_vqs() is no longer present, rename
virtio_find_vqs_info() back to virtio_find_vqs().
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Message-Id: <20240708074814.1739223-20-jiri@resnulli.us>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of passing separate names and callbacks arrays
to virtio_find_vqs(), allocate one of virtual_queue_info structs and
pass it to virtio_find_vqs_info().
Suggested-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Message-Id: <20240708074814.1739223-11-jiri@resnulli.us>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----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=wVi8
-----END PGP SIGNATURE-----
Merge tag 'for-6.11/block-20240710' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe updates via Keith:
- Device initialization memory leak fixes (Keith)
- More constants defined (Weiwen)
- Target debugfs support (Hannes)
- PCIe subsystem reset enhancements (Keith)
- Queue-depth multipath policy (Redhat and PureStorage)
- Implement get_unique_id (Christoph)
- Authentication error fixes (Gaosheng)
- MD updates via Song
- sync_action fix and refactoring (Yu Kuai)
- Various small fixes (Christoph Hellwig, Li Nan, and Ofir Gal, Yu
Kuai, Benjamin Marzinski, Christophe JAILLET, Yang Li)
- Fix loop detach/open race (Gulam)
- Fix lower control limit for blk-throttle (Yu)
- Add module descriptions to various drivers (Jeff)
- Add support for atomic writes for block devices, and statx reporting
for same. Includes SCSI and NVMe (John, Prasad, Alan)
- Add IO priority information to block trace points (Dongliang)
- Various zone improvements and tweaks (Damien)
- mq-deadline tag reservation improvements (Bart)
- Ignore direct reclaim swap writes in writeback throttling (Baokun)
- Block integrity improvements and fixes (Anuj)
- Add basic support for rust based block drivers. Has a dummy null_blk
variant for now (Andreas)
- Series converting driver settings to queue limits, and cleanups and
fixes related to that (Christoph)
- Cleanup for poking too deeply into the bvec internals, in preparation
for DMA mapping API changes (Christoph)
- Various minor tweaks and fixes (Jiapeng, John, Kanchan, Mikulas,
Ming, Zhu, Damien, Christophe, Chaitanya)
* tag 'for-6.11/block-20240710' of git://git.kernel.dk/linux: (206 commits)
floppy: add missing MODULE_DESCRIPTION() macro
loop: add missing MODULE_DESCRIPTION() macro
ublk_drv: add missing MODULE_DESCRIPTION() macro
xen/blkback: add missing MODULE_DESCRIPTION() macro
block/rnbd: Constify struct kobj_type
block: take offset into account in blk_bvec_map_sg again
block: fix get_max_segment_size() warning
loop: Don't bother validating blocksize
virtio_blk: Don't bother validating blocksize
null_blk: Don't bother validating blocksize
block: Validate logical block size in blk_validate_limits()
virtio_blk: Fix default logical block size fallback
nvmet-auth: fix nvmet_auth hash error handling
nvme: implement ->get_unique_id
block: pass a phys_addr_t to get_max_segment_size
block: add a bvec_phys helper
blk-lib: check for kill signal in ioctl BLKZEROOUT
block: limit the Write Zeroes to manually writing zeroes fallback
block: refacto blkdev_issue_zeroout
block: move read-only and supported checks into (__)blkdev_issue_zeroout
...
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/block/floppy.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Denis Efremov <efremov@linux.com>
Link: https://lore.kernel.org/r/20240602-md-block-floppy-v1-1-bc628ea5eb84@quicinc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/block/loop.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240602-md-block-loop-v1-1-b9b7e2603e72@quicinc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/block/ublk_drv.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240602-md-block-ublk_drv-v1-1-995474cafff0@quicinc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/block/xen-blkback/xen-blkback.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240602-md-block-xen-blkback-v1-1-6ff5b58bdee1@quicinc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
'struct kobj_type' is not modified in this driver. It is only used with
kobject_init_and_add() which takes a "const struct kobj_type *" parameter.
Constifying this structure moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
4082 792 8 4882 1312 drivers/block/rnbd/rnbd-srv-sysfs.o
After:
=====
text data bss dec hex filename
4210 672 8 4890 131a drivers/block/rnbd/rnbd-srv-sysfs.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/e3d454173ffad30726c9351810d3aa7b75122711.1720462252.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The block queue limits validation does this for us now.
The loop_configure() -> WARN_ON_ONCE() call is dropped, as an invalid
block size would trigger this now. We don't want userspace to be able to
directly trigger WARNs.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Link: https://lore.kernel.org/r/20240708091651.177447-6-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The block queue limits validation does this for us now.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240708091651.177447-5-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The block queue limits validation does this for us now.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Link: https://lore.kernel.org/r/20240708091651.177447-4-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we fail to read a logical block size in virtblk_read_limits() ->
virtio_cread_feature(), then we default to what is in
lim->logical_block_size, but that would be 0.
We can deal with lim->logical_block_size = 0 later in the
blk_mq_alloc_disk(), but the code in virtblk_read_limits() needs a proper
default, so give a default of SECTOR_SIZE.
Fixes: 27e32cd23f ("block: pass a queue_limits argument to blk_mq_alloc_disk")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240708091651.177447-2-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that device mapper can handle resetting all zones of a mapped zoned
device using REQ_OP_ZONE_RESET_ALL, all zoned block device drivers
support this operation. With this, the request queue feature
BLK_FEAT_ZONE_RESETALL is not necessary and the emulation code in
blk-zone.c can be removed.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240704052816.623865-5-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Allow creating a zoned null_blk device with the initial state of its
sequential write required zones to be FULL. This is convenient to avoid
having to first write these zones to perform read performance evaluation
or test zone management operations such as zone reset (and zone reset
all).
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240704052816.623865-2-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove the inode variable now that the last user is gone.
Fixes: a17ece76bc ("loop: regularize upgrading the block size for direct I/O")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240705053114.2042976-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Let's clean it up: use a proper page type and store our data (offset into
a page) in the lower 16 bit as documented.
We won't be able to support 256 KiB base pages, which is acceptable.
Teach Kconfig to handle that cleanly using a new CONFIG_HAVE_ZSMALLOC.
Based on this, we should do a proper "struct zsdesc" conversion, as
proposed in [1].
This removes the last _mapcount/page_type offender.
[1] https://lore.kernel.org/all/20231130101242.2590384-1-42.hyeyoo@gmail.com/
Link: https://lkml.kernel.org/r/20240529111904.2069608-4-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Tested-by: Sergey Senozhatsky <senozhatsky@chromium.org> [zram/zsmalloc workloads]
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Ensure that info->sector_size and info->physical_sector_size are set
before the call to blkif_set_queue_limits by doing away with the
local variables and arguments that propagate them.
Thanks to Marek Marczykowski-Górecki and Jürgen Groß for root causing
the issue.
Fixes: ba3f67c116 ("xen-blkfront: atomically update queue limits")
Reported-by: Rusty Bird <rustybird@net-c.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
Link: https://lore.kernel.org/r/20240625055238.7934-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The description of the fua module parameter is defined using
MODULE_PARM_DESC() with the first argument passed being "zoned". That is
the wrong name, obviously. Fix that by using the correct "fua" parameter
name so that "modinfo null_blk" displays correct information.
Fixes: f4f84586c8 ("null_blk: Introduce fua attribute")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20240702073234.206458-1-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
QUEUE_FLAG_SAME_FORCE has been set by rnbd-cnt since the initial
merge. There is no good reason for a driver to force exact core
delivery, which is tunable for very specific workloads and not a
driver setting.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240627124926.512662-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
QUEUE_FLAG_SAME_COMP is already set by default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240627124926.512662-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
QUEUE_FLAG_NOMERGES isn't really a driver interface, but a user tunable.
There also isn't any good reason to set it in the loop driver.
The original commit adding it (5b5e20f421 "block: loop: set
QUEUE_FLAG_NOMERGES for request queue of loop") claims that "It doesn't
make sense to enable merge because the I/O submitted to backing file is
handled page by page." which of course isn't true for multi-page bvec
now, and it never has been for direct I/O, for which commit 40326d8a33
("block/loop: allow request merge for directio mode") alredy disabled
the nomerges flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240627124926.512662-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
1. Userspace sends the command "losetup -d" which uses the open() call
to open the device
2. Kernel receives the ioctl command "LOOP_CLR_FD" which calls the
function loop_clr_fd()
3. If LOOP_CLR_FD is the first command received at the time, then the
AUTOCLEAR flag is not set and deletion of the
loop device proceeds ahead and scans the partitions (drop/add
partitions)
if (disk_openers(lo->lo_disk) > 1) {
lo->lo_flags |= LO_FLAGS_AUTOCLEAR;
loop_global_unlock(lo, true);
return 0;
}
4. Before scanning partitions, it will check to see if any partition of
the loop device is currently opened
5. If any partition is opened, then it will return EBUSY:
if (disk->open_partitions)
return -EBUSY;
6. So, after receiving the "LOOP_CLR_FD" command and just before the above
check for open_partitions, if any other command
(like blkid) opens any partition of the loop device, then the partition
scan will not proceed and EBUSY is returned as shown in above code
7. But in "__loop_clr_fd()", this EBUSY error is not propagated
8. We have noticed that this is causing the partitions of the loop to
remain stale even after the loop device is detached resulting in the
IO errors on the partitions
Fix:
Defer the detach of loop device to release function, which is called when
the last close happens, by setting the lo_flags to LO_FLAGS_AUTOCLEAR at
the time of detach i.e in loop_clr_fd() function.
Test case involves the following two scripts:
script1.sh:
while [ 1 ];
do
losetup -P -f /home/opt/looptest/test10.img
blkid /dev/loop0p1
done
script2.sh:
while [ 1 ];
do
losetup -d /dev/loop0
done
Without fix, the following IO errors have been observed:
kernel: __loop_clr_fd: partition scan of loop0 failed (rc=-16)
kernel: I/O error, dev loop0, sector 20971392 op 0x0:(READ) flags 0x80700
phys_seg 1 prio class 0
kernel: I/O error, dev loop0, sector 108868 op 0x0:(READ) flags 0x0
phys_seg 1 prio class 0
kernel: Buffer I/O error on dev loop0p1, logical block 27201, async page
read
Signed-off-by: Gulam Mohamed <gulam.mohamed@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240618164042.343777-1-gulam.mohamed@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
make allmodconfig && make W=1 C=1 reports:
modpost: missing MODULE_DESCRIPTION() in drivers/block/brd.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240602-md-block-brd-v1-1-e71338e131b6@quicinc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In null_register_zoned_dev(), there is no need to set disk->nr_zones as
the now uncoditional call to blk_revalidate_disk_zones() will do that.
So remove the assignment using bdev_nr_zones().
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20240621031506.759397-2-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge in last round of queue limits changes from Christoph.
* for-6.11/block-limits: (26 commits)
block: move the bounce flag into the features field
block: move the skip_tagset_quiesce flag to queue_limits
block: move the pci_p2pdma flag to queue_limits
block: move the zone_resetall flag to queue_limits
block: move the zoned flag into the features field
block: move the poll flag to queue_limits
block: move the dax flag to queue_limits
block: move the nowait flag to queue_limits
block: move the synchronous flag to queue_limits
block: move the stable_writes flag to queue_limits
block: move the io_stat flag setting to queue_limits
block: move the add_random flag to queue_limits
block: move the nonrot flag to queue_limits
block: move cache control settings out of queue->flags
block: remove blk_flush_policy
block: freeze the queue in queue_attr_store
nbd: move setting the cache control flags to __nbd_set_size
virtio_blk: remove virtblk_update_cache_mode
loop: fold loop_update_rotational into loop_reconfigure_limits
loop: also use the default block size from an underlying block device
...
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the zone_resetall flag into the queue_limits feature field so that
it can be set atomically with the queue frozen.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-24-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the zoned flags into the features field to reclaim a little
bit of space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-23-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the nowait flag into the queue_limits feature field so that it can
be set atomically with the queue frozen.
Stacking drivers are simplified in that they now can simply set the
flag, and blk_stack_limits will clear it when the features is not
supported by any of the underlying devices.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-20-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the synchronous flag into the queue_limits feature field so that it
can be set atomically with the queue frozen.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-19-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the stable_writes flag into the queue_limits feature field so that
it can be set atomically with the queue frozen.
The flag is now inherited by blk_stack_limits, which greatly simplifies
the code in dm, and fixed md which previously did not pass on the flag
set on lower devices.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-18-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the add_random flag into the queue_limits feature field so that it
can be set atomically with the queue frozen.
Note that this also removes code from dm to clear the flag based on
the underlying devices, which can't be reached as dm devices will
always start out without the flag set.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-16-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the nonrot flag into the queue_limits feature field so that it can
be set atomically with the queue frozen.
Use the chance to switch to defaulting to non-rotational and require
the driver to opt into rotational, which matches the polarity of the
sysfs interface.
For the z2ram, ps3vram, 2x memstick, ubiblock and dcssblk the new
rotational flag is not set as they clearly are not rotational despite
this being a behavior change. There are some other drivers that
unconditionally set the rotational flag to keep the existing behavior
as they arguably can be used on rotational devices even if that is
probably not their main use today (e.g. virtio_blk and drbd).
The flag is automatically inherited in blk_stack_limits matching the
existing behavior in dm and md.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-15-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the cache control settings into the queue_limits so that the flags
can be set atomically with the device queue frozen.
Add new features and flags field for the driver set flags, and internal
(usually sysfs-controlled) flags in the block layer. Note that we'll
eventually remove enough field from queue_limits to bring it back to the
previous size.
The disable flag is inverted compared to the previous meaning, which
means it now survives a rescan, similar to the max_sectors and
max_discard_sectors user limits.
The FLUSH and FUA flags are now inherited by blk_stack_limits, which
simplified the code in dm a lot, but also causes a slight behavior
change in that dm-switch and dm-unstripe now advertise a write cache
despite setting num_flush_bios to 0. The I/O path will handle this
gracefully, but as far as I can tell the lack of num_flush_bios
and thus flush support is a pre-existing data integrity bug in those
targets that really needs fixing, after which a non-zero num_flush_bios
should be required in dm for targets that map to underlying devices.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-14-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move setting the cache control flags in nbd in preparation for moving
these flags into the queue_limits structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-11-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
virtblk_update_cache_mode boils down to a single call to
blk_queue_write_cache. Remove it in preparation for moving the cache
control flags into the queue_limits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20240617060532.127975-10-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This prepares for moving the rotational flag into the queue_limits and
also fixes it for the case where the loop device is backed by a block
device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240617060532.127975-9-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix the code in loop_reconfigure_limits to pick a default block size for
O_DIRECT file descriptors to also work when the loop device sits on top
of a block device and not just on a regular file on a block device based
file system.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240617060532.127975-8-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The LOOP_CONFIGURE path automatically upgrades the block size to that
of the underlying file for O_DIRECT file descriptors, but the
LOOP_SET_BLOCK_SIZE path does not. Fix this by lifting the code to
pick the block size into common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240617060532.127975-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Simplify loop_reconfigure_limits by always updating the discard limits.
This adds a little more work to loop_set_block_size, but doesn't change
the outcome as the discard flag won't change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240617060532.127975-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
__loop_clr_fd wants to clear all settings on the device. Prepare for
moving more settings into the block limits by open coding
loop_reconfigure_limits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240617060532.127975-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blkfront always had a robust negotiation protocol for detecting a write
cache. Stop simply disabling cache flushes in the block layer as the
flags handling is moving to the atomic queue limits API that needs
user context to freeze the queue for that. Instead handle the case
of the feature flags cleared inside of blkfront. This removes old
debug code to check for such a mismatch which was previously impossible
to hit, including the check for passthrough requests that blkfront
never used to start with.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240617060532.127975-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With ARCH=m68k, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/block/z2ram.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20240617-md-m68k-drivers-block-v1-3-b200599a315e@quicinc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With ARCH=m68k, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/block/ataflop.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20240617-md-m68k-drivers-block-v1-2-b200599a315e@quicinc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With ARCH=m68k, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/block/amiflop.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20240617-md-m68k-drivers-block-v1-1-b200599a315e@quicinc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull in block limits branch, which exists as a shared branch for both
the block and SCSI tree.
* for-6.11/block-limits: (26 commits)
block: move integrity information into queue_limits
block: invert the BLK_INTEGRITY_{GENERATE,VERIFY} flags
block: bypass the STABLE_WRITES flag for protection information
block: don't require stable pages for non-PI metadata
block: use kstrtoul in flag_store
block: factor out flag_{store,show} helper for integrity
block: remove the blk_flush_integrity call in blk_integrity_unregister
block: remove the blk_integrity_profile structure
dm-integrity: use the nop integrity profile
md/raid1: don't free conf on raid0_run failure
md/raid0: don't free conf on raid0_run failure
block: initialize integrity buffer to zero before writing it to media
block: add special APIs for run-time disabling of discard and friends
block: remove unused queue limits API
sr: convert to the atomic queue limits API
sd: convert to the atomic queue limits API
sd: cleanup zoned queue limits initialization
sd: factor out a sd_discard_mode helper
sd: simplify the disable case in sd_config_discard
sd: add a sd_disable_write_same helper
...
A few drivers optimistically try to support discard, write zeroes and
secure erase and disable the features from the I/O completion handler
if the hardware can't support them. This disable can't be done using
the atomic queue limits API because the I/O completion handlers can't
take sleeping locks or freeze the queue. Keep the existing clearing
of the relevant field to zero, but replace the old blk_queue_max_*
APIs with new disable APIs that force the value to 0.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Nitesh Shetty <nj.shetty@samsung.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240531074837.1648501-15-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The soft max_sectors limit is normally capped by the hardware limits and
an arbitrary upper limit enforced by the kernel, but can be modified by
the user. A few drivers want to increase this limit (nbd, rbd) or
adjust it up or down based on hardware capabilities (sd).
Change blk_validate_limits to default max_sectors to the optimal I/O
size, or upgrade it to the preferred minimal I/O size if that is
larger than the kernel default if no optimal I/O size is provided based
on the logic in the SD driver.
This keeps the existing kernel default for drivers that do not provide
an io_opt or very big io_min value, but picks a much more useful
default for those who provide these hints, and allows to remove the
hacks to set the user max_sectors limit in nbd, rbd and sd.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240531074837.1648501-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 16d80c54ad ("rbd: set io_min, io_opt and discard_granularity to
alloc_size") lowered the io_opt size for rbd from objset_bytes which is
4MB for typical setup to alloc_size which is typically 64KB.
The commit mostly talks about discard behavior and does mention io_min
in passing. Reducing io_opt means reducing the readahead size, which
seems counter-intuitive given that rbd currently abuses the user
max_sectors setting to actually increase the I/O size. Switch back
to the old setting to allow larger reads (the readahead size despite it's
name actually limits the size of any buffered read) and to prepare
for using io_opt in the max_sectors calculation and getting drivers out
of the business of overriding the max_user_sectors value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240531074837.1648501-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch adds an initial version of the Rust null block driver.
Signed-off-by: Andreas Hindborg <a.hindborg@samsung.com>
Reviewed-by: Benno Lossin <benno.lossin@proton.me>
Link: https://lore.kernel.org/r/20240611114551.228679-3-nmi@metaspace.dk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If fallcate is implemented but zero and discard operations are not
supported by the filesystem the backing file is on we continue to fill
dmesg with errors from the blk_mq_end_request() since each time we call
fallocate() on the loop device the EOPNOTSUPP error from lo_fallocate()
ends up propagated into the block layer. In the end syscall succeeds
since the blkdev_issue_zeroout() falls back to writing zeroes which
makes the errors even more misleading and confusing.
How to reproduce:
1. make sure /tmp is mounted as tmpfs
2. dd if=/dev/zero of=/tmp/disk.img bs=1M count=100
3. losetup /dev/loop0 /tmp/disk.img
4. mkfs.ext2 /dev/loop0
5. dmesg |tail
[710690.898214] operation not supported error, dev loop0, sector 204672 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.898279] operation not supported error, dev loop0, sector 522 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.898603] operation not supported error, dev loop0, sector 16906 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.898917] operation not supported error, dev loop0, sector 32774 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.899218] operation not supported error, dev loop0, sector 49674 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.899484] operation not supported error, dev loop0, sector 65542 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.899743] operation not supported error, dev loop0, sector 82442 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.900015] operation not supported error, dev loop0, sector 98310 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.900276] operation not supported error, dev loop0, sector 115210 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
[710690.900546] operation not supported error, dev loop0, sector 131078 op 0x9:(WRITE_ZEROES) flags 0x8000800 phys_seg 0 prio class 0
This patch changes the lo_fallocate() to clear the flags for zero and
discard operations if we get EOPNOTSUPP from the backing file fallocate
callback, that way we at least stop spewing errors after the first
unsuccessful try.
CC: Jan Kara <jack@suse.cz>
Signed-off-by: Cyril Hrubis <chrubis@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20240613163817.22640-1-chrubis@suse.cz
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Make it again possible for sparse to verify that blk_status_t and Unix
error codes are used in the proper context by making nbd_send_cmd()
return a blk_status_t instead of an integer.
No functionality has been changed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: added description and made two small formatting changes ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20240604221531.327131-1-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Block size should be between 512 and PAGE_SIZE and be a power of 2. The current
check does not validate this, so update the check.
Without this patch, null_blk would Oops due to a null pointer deref when
loaded with bs=1536 [1].
Link: https://lore.kernel.org/all/87wmn8mocd.fsf@metaspace.dk/
Signed-off-by: Andreas Hindborg <a.hindborg@samsung.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240603192645.977968-1-nmi@metaspace.dk
[axboe: remove unnecessary braces and != 0 check]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A zoned device with a smaller last zone together with a zone capacity
smaller than the zone size does make any sense as that does not
correspond to any possible setup for a real device:
1) For ZNS and zoned UFS devices, all zones are always the same size.
2) For SMR HDDs, all zones always have the same capacity.
In other words, if we have a smaller last runt zone, then this zone
capacity should always be equal to the zone size.
Add a check in null_init_zoned_dev() to prevent a configuration to have
both a smaller zone size and a zone capacity smaller than the zone size.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240530054035.491497-2-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When changing the maximum number of open zones, print that number
instead of the total number of zones.
Fixes: dc4d137ee3 ("null_blk: add support for max open/active zone limit for zoned devices")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20240528062852.437599-1-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When powering on a null_blk device that is not already on, the return
value ret that is initialized to be count is reused to check the return
value of null_add_dev(), leading to nullb_device_power_store() to return
null_add_dev() return value (0 on success) instead of "count".
So make sure to set ret to be equal to count when there are no errors.
Fixes: a2db328b08 ("null_blk: fix null-ptr-dereference while configuring 'power' and 'submit_queues'")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Link: https://lore.kernel.org/r/20240527043445.235267-1-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=Btam
-----END PGP SIGNATURE-----
Merge tag 'block-6.10-20240523' of git://git.kernel.dk/linux
Pull more block updates from Jens Axboe:
"Followup block updates, mostly due to NVMe being a bit late to the
party. But nothing major in there, so not a big deal.
In detail, this contains:
- NVMe pull request via Keith:
- Fabrics connection retries (Daniel, Hannes)
- Fabrics logging enhancements (Tokunori)
- RDMA delete optimization (Sagi)
- ublk DMA alignment fix (me)
- null_blk sparse warning fixes (Bart)
- Discard support for brd (Keith)
- blk-cgroup list corruption fixes (Ming)
- blk-cgroup stat propagation fix (Waiman)
- Regression fix for plugging stall with md (Yu)
- Misc fixes or cleanups (David, Jeff, Justin)"
* tag 'block-6.10-20240523' of git://git.kernel.dk/linux: (24 commits)
null_blk: fix null-ptr-dereference while configuring 'power' and 'submit_queues'
blk-throttle: remove unused struct 'avg_latency_bucket'
block: fix lost bio for plug enabled bio based device
block: t10-pi: add MODULE_DESCRIPTION()
blk-mq: add helper for checking if one CPU is mapped to specified hctx
blk-cgroup: Properly propagate the iostat update up the hierarchy
blk-cgroup: fix list corruption from reorder of WRITE ->lqueued
blk-cgroup: fix list corruption from resetting io stat
cdrom: rearrange last_media_change check to avoid unintentional overflow
nbd: Fix signal handling
nbd: Remove a local variable from nbd_send_cmd()
nbd: Improve the documentation of the locking assumptions
nbd: Remove superfluous casts
nbd: Use NULL to represent a pointer
brd: implement discard support
null_blk: Fix two sparse warnings
ublk_drv: set DMA alignment mask to 3
nvme-rdma, nvme-tcp: include max reconnects for reconnect logging
nvmet-rdma: Avoid o(n^2) loop in delete_ctrl
nvme: do not retry authentication failures
...
The __assign_str() macro logic of the TRACE_EVENT() macro was optimized so
that it no longer needs the second argument. The __assign_str() is always
matched with __string() field that takes a field name and the source for
that field:
__string(field, source)
The TRACE_EVENT() macro logic will save off the source value and then use
that value to copy into the ring buffer via the __assign_str(). Before
commit c1fa617cae ("tracing: Rework __assign_str() and __string() to not
duplicate getting the string"), the __assign_str() needed the second
argument which would perform the same logic as the __string() source
parameter did. Not only would this add overhead, but it was error prone as
if the __assign_str() source produced something different, it may not have
allocated enough for the string in the ring buffer (as the __string()
source was used to determine how much to allocate)
Now that the __assign_str() just uses the same string that was used in
__string() it no longer needs the source parameter. It can now be removed.
-----BEGIN PGP SIGNATURE-----
iIkEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCZk9RMBQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qur+AP9jbSYaGhzZdJ7a3HGA8M4l6JNju8nC
GcX1JpJT4z1qvgD3RkoNvP87etDAUAqmbVhVWnUHCY/vTqr9uB/gqmG6Ag==
=Y+6f
-----END PGP SIGNATURE-----
Merge tag 'trace-assign-str-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing cleanup from Steven Rostedt:
"Remove second argument of __assign_str()
The __assign_str() macro logic of the TRACE_EVENT() macro was
optimized so that it no longer needs the second argument. The
__assign_str() is always matched with __string() field that takes a
field name and the source for that field:
__string(field, source)
The TRACE_EVENT() macro logic will save off the source value and then
use that value to copy into the ring buffer via the __assign_str().
Before commit c1fa617cae ("tracing: Rework __assign_str() and
__string() to not duplicate getting the string"), the __assign_str()
needed the second argument which would perform the same logic as the
__string() source parameter did. Not only would this add overhead, but
it was error prone as if the __assign_str() source produced something
different, it may not have allocated enough for the string in the ring
buffer (as the __string() source was used to determine how much to
allocate)
Now that the __assign_str() just uses the same string that was used in
__string() it no longer needs the source parameter. It can now be
removed"
* tag 'trace-assign-str-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/treewide: Remove second parameter of __assign_str()
Several new features here:
- virtio-net is finally supported in vduse.
- Virtio (balloon and mem) interaction with suspend is improved
- vhost-scsi now handles signals better/faster.
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmZN570PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp2JUH/1K3fZOHymop6Y5Z3USFS7YdlF+dniedY/vg
TKyWERkXOlxq1d9DVxC0mN7tk72DweuWI0YJjLXofrEW1VuW29ecSbyFXxpeWJls
b7ErffxDAFRas5jkMCngD8TuFnbEegU0mGP5kbiHpEndBydQ2hH99Gg0x7swW+cE
xsvU5zonCCLwLGIP2DrVrn9qGOHtV6o8eZfVKDVXfvicn3lFBkUSxlwEYsO9RMup
aKxV4FT2Pb1yBicwBK4TH1oeEXqEGy1YLEn+kAHRbgoC/5L0/LaiqrkzwzwwOIPj
uPGkacf8CIbX0qZo5EzD8kvfcYL1xhU3eT9WBmpp2ZwD+4bINd4=
=nax1
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"Several new features here:
- virtio-net is finally supported in vduse
- virtio (balloon and mem) interaction with suspend is improved
- vhost-scsi now handles signals better/faster
And fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (48 commits)
virtio-pci: Check if is_avq is NULL
virtio: delete vq in vp_find_vqs_msix() when request_irq() fails
MAINTAINERS: add Eugenio Pérez as reviewer
vhost-vdpa: Remove usage of the deprecated ida_simple_xx() API
vp_vdpa: don't allocate unused msix vectors
sound: virtio: drop owner assignment
fuse: virtio: drop owner assignment
scsi: virtio: drop owner assignment
rpmsg: virtio: drop owner assignment
nvdimm: virtio_pmem: drop owner assignment
wifi: mac80211_hwsim: drop owner assignment
vsock/virtio: drop owner assignment
net: 9p: virtio: drop owner assignment
net: virtio: drop owner assignment
net: caif: virtio: drop owner assignment
misc: nsm: drop owner assignment
iommu: virtio: drop owner assignment
drm/virtio: drop owner assignment
gpio: virtio: drop owner assignment
firmware: arm_scmi: virtio: drop owner assignment
...
Writing 'power' and 'submit_queues' concurrently will trigger kernel
panic:
Test script:
modprobe null_blk nr_devices=0
mkdir -p /sys/kernel/config/nullb/nullb0
while true; do echo 1 > submit_queues; echo 4 > submit_queues; done &
while true; do echo 1 > power; echo 0 > power; done
Test result:
BUG: kernel NULL pointer dereference, address: 0000000000000148
Oops: 0000 [#1] PREEMPT SMP
RIP: 0010:__lock_acquire+0x41d/0x28f0
Call Trace:
<TASK>
lock_acquire+0x121/0x450
down_write+0x5f/0x1d0
simple_recursive_removal+0x12f/0x5c0
blk_mq_debugfs_unregister_hctxs+0x7c/0x100
blk_mq_update_nr_hw_queues+0x4a3/0x720
nullb_update_nr_hw_queues+0x71/0xf0 [null_blk]
nullb_device_submit_queues_store+0x79/0xf0 [null_blk]
configfs_write_iter+0x119/0x1e0
vfs_write+0x326/0x730
ksys_write+0x74/0x150
This is because del_gendisk() can concurrent with
blk_mq_update_nr_hw_queues():
nullb_device_power_store nullb_apply_submit_queues
null_del_dev
del_gendisk
nullb_update_nr_hw_queues
if (!dev->nullb)
// still set while gendisk is deleted
return 0
blk_mq_update_nr_hw_queues
dev->nullb = NULL
Fix this problem by resuing the global mutex to protect
nullb_device_power_store() and nullb_update_nr_hw_queues() from configfs.
Fixes: 45919fbfe1 ("null_blk: Enable modifying 'submit_queues' after an instance has been configured")
Reported-and-tested-by: Yi Zhang <yi.zhang@redhat.com>
Closes: https://lore.kernel.org/all/CAHj4cs9LgsHLnjg8z06LQ3Pr5cax-+Ps+xT7AP7TPnEjStuwZA@mail.gmail.com/
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Link: https://lore.kernel.org/r/20240523153934.1937851-1-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
virtio core already sets the .owner, so driver does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Message-Id: <20240331-module-owner-virtio-v2-6-98f04bfaf46a@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCZkzp/gAKCRBZ7Krx/gZQ
63KFAQCsKv3XdcF+2BO+QuwPvR6eAvDxFjrFEcQFyyOXgFVLaAD/UMM0HcEFWxBb
PCPvyKVP22wF9PbodkrKJn8DRdtRZwM=
=jvWv
-----END PGP SIGNATURE-----
Merge tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs updates from Al Viro:
"Assorted commits that had missed the last merge window..."
* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
remove call_{read,write}_iter() functions
do_dentry_open(): kill inode argument
kernel_file_open(): get rid of inode argument
get_file_rcu(): no need to check for NULL separately
fd_is_open(): move to fs/file.c
close_on_exec(): pass files_struct instead of fdtable
to struct file * and verifying that caller has device
opened exclusively.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCZkwkfQAKCRBZ7Krx/gZQ
62C3AQDW5vuXNx2+KDPma5YStjFpPLC0xtSyAS5D3YANjtyRFgD/TOcCarq7rvBt
KubxHVFsfW+eu6ASeaoMRB83w5OIzwk=
=Liix
-----END PGP SIGNATURE-----
Merge tag 'pull-set_blocksize' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs blocksize updates from Al Viro:
"This gets rid of bogus set_blocksize() uses, switches it over
to be based on a 'struct file *' and verifies that the caller
has the device opened exclusively"
* tag 'pull-set_blocksize' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
make set_blocksize() fail unless block device is opened exclusive
set_blocksize(): switch to passing struct file *
btrfs_get_bdev_and_sb(): call set_blocksize() only for exclusive opens
swsusp: don't bother with setting block size
zram: don't bother with reopening - just use O_EXCL for open
swapon(2): open swap with O_EXCL
swapon(2)/swapoff(2): don't bother with block size
pktcdvd: sort set_blocksize() calls out
bcache_register(): don't bother with set_blocksize()
documented (hopefully adequately) in the respective changelogs. Notable
series include:
- Lucas Stach has provided some page-mapping
cleanup/consolidation/maintainability work in the series "mm/treewide:
Remove pXd_huge() API".
- In the series "Allow migrate on protnone reference with
MPOL_PREFERRED_MANY policy", Donet Tom has optimized mempolicy's
MPOL_PREFERRED_MANY mode, yielding almost doubled performance in one
test.
- In their series "Memory allocation profiling" Kent Overstreet and
Suren Baghdasaryan have contributed a means of determining (via
/proc/allocinfo) whereabouts in the kernel memory is being allocated:
number of calls and amount of memory.
- Matthew Wilcox has provided the series "Various significant MM
patches" which does a number of rather unrelated things, but in largely
similar code sites.
- In his series "mm: page_alloc: freelist migratetype hygiene" Johannes
Weiner has fixed the page allocator's handling of migratetype requests,
with resulting improvements in compaction efficiency.
- In the series "make the hugetlb migration strategy consistent" Baolin
Wang has fixed a hugetlb migration issue, which should improve hugetlb
allocation reliability.
- Liu Shixin has hit an I/O meltdown caused by readahead in a
memory-tight memcg. Addressed in the series "Fix I/O high when memory
almost met memcg limit".
- In the series "mm/filemap: optimize folio adding and splitting" Kairui
Song has optimized pagecache insertion, yielding ~10% performance
improvement in one test.
- Baoquan He has cleaned up and consolidated the early zone
initialization code in the series "mm/mm_init.c: refactor
free_area_init_core()".
- Baoquan has also redone some MM initializatio code in the series
"mm/init: minor clean up and improvement".
- MM helper cleanups from Christoph Hellwig in his series "remove
follow_pfn".
- More cleanups from Matthew Wilcox in the series "Various page->flags
cleanups".
- Vlastimil Babka has contributed maintainability improvements in the
series "memcg_kmem hooks refactoring".
- More folio conversions and cleanups in Matthew Wilcox's series
"Convert huge_zero_page to huge_zero_folio"
"khugepaged folio conversions"
"Remove page_idle and page_young wrappers"
"Use folio APIs in procfs"
"Clean up __folio_put()"
"Some cleanups for memory-failure"
"Remove page_mapping()"
"More folio compat code removal"
- David Hildenbrand chipped in with "fs/proc/task_mmu: convert hugetlb
functions to work on folis".
- Code consolidation and cleanup work related to GUP's handling of
hugetlbs in Peter Xu's series "mm/gup: Unify hugetlb, part 2".
- Rick Edgecombe has developed some fixes to stack guard gaps in the
series "Cover a guard gap corner case".
- Jinjiang Tu has fixed KSM's behaviour after a fork+exec in the series
"mm/ksm: fix ksm exec support for prctl".
- Baolin Wang has implemented NUMA balancing for multi-size THPs. This
is a simple first-cut implementation for now. The series is "support
multi-size THP numa balancing".
- Cleanups to vma handling helper functions from Matthew Wilcox in the
series "Unify vma_address and vma_pgoff_address".
- Some selftests maintenance work from Dev Jain in the series
"selftests/mm: mremap_test: Optimizations and style fixes".
- Improvements to the swapping of multi-size THPs from Ryan Roberts in
the series "Swap-out mTHP without splitting".
- Kefeng Wang has significantly optimized the handling of arm64's
permission page faults in the series
"arch/mm/fault: accelerate pagefault when badaccess"
"mm: remove arch's private VM_FAULT_BADMAP/BADACCESS"
- GUP cleanups from David Hildenbrand in "mm/gup: consistently call it
GUP-fast".
- hugetlb fault code cleanups from Vishal Moola in "Hugetlb fault path to
use struct vm_fault".
- selftests build fixes from John Hubbard in the series "Fix
selftests/mm build without requiring "make headers"".
- Memory tiering fixes/improvements from Ho-Ren (Jack) Chuang in the
series "Improved Memory Tier Creation for CPUless NUMA Nodes". Fixes
the initialization code so that migration between different memory types
works as intended.
- David Hildenbrand has improved follow_pte() and fixed an errant driver
in the series "mm: follow_pte() improvements and acrn follow_pte()
fixes".
- David also did some cleanup work on large folio mapcounts in his
series "mm: mapcount for large folios + page_mapcount() cleanups".
- Folio conversions in KSM in Alex Shi's series "transfer page to folio
in KSM".
- Barry Song has added some sysfs stats for monitoring multi-size THP's
in the series "mm: add per-order mTHP alloc and swpout counters".
- Some zswap cleanups from Yosry Ahmed in the series "zswap same-filled
and limit checking cleanups".
- Matthew Wilcox has been looking at buffer_head code and found the
documentation to be lacking. The series is "Improve buffer head
documentation".
- Multi-size THPs get more work, this time from Lance Yang. His series
"mm/madvise: enhance lazyfreeing with mTHP in madvise_free" optimizes
the freeing of these things.
- Kemeng Shi has added more userspace-visible writeback instrumentation
in the series "Improve visibility of writeback".
- Kemeng Shi then sent some maintenance work on top in the series "Fix
and cleanups to page-writeback".
- Matthew Wilcox reduces mmap_lock traffic in the anon vma code in the
series "Improve anon_vma scalability for anon VMAs". Intel's test bot
reported an improbable 3x improvement in one test.
- SeongJae Park adds some DAMON feature work in the series
"mm/damon: add a DAMOS filter type for page granularity access recheck"
"selftests/damon: add DAMOS quota goal test"
- Also some maintenance work in the series
"mm/damon/paddr: simplify page level access re-check for pageout"
"mm/damon: misc fixes and improvements"
- David Hildenbrand has disabled some known-to-fail selftests ni the
series "selftests: mm: cow: flag vmsplice() hugetlb tests as XFAIL".
- memcg metadata storage optimizations from Shakeel Butt in "memcg:
reduce memory consumption by memcg stats".
- DAX fixes and maintenance work from Vishal Verma in the series
"dax/bus.c: Fixups for dax-bus locking".
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZkgQYwAKCRDdBJ7gKXxA
jrdKAP9WVJdpEcXxpoub/vVE0UWGtffr8foifi9bCwrQrGh5mgEAx7Yf0+d/oBZB
nvA4E0DcPrUAFy144FNM0NTCb7u9vAw=
=V3R/
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2024-05-17-19-19' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull mm updates from Andrew Morton:
"The usual shower of singleton fixes and minor series all over MM,
documented (hopefully adequately) in the respective changelogs.
Notable series include:
- Lucas Stach has provided some page-mapping cleanup/consolidation/
maintainability work in the series "mm/treewide: Remove pXd_huge()
API".
- In the series "Allow migrate on protnone reference with
MPOL_PREFERRED_MANY policy", Donet Tom has optimized mempolicy's
MPOL_PREFERRED_MANY mode, yielding almost doubled performance in
one test.
- In their series "Memory allocation profiling" Kent Overstreet and
Suren Baghdasaryan have contributed a means of determining (via
/proc/allocinfo) whereabouts in the kernel memory is being
allocated: number of calls and amount of memory.
- Matthew Wilcox has provided the series "Various significant MM
patches" which does a number of rather unrelated things, but in
largely similar code sites.
- In his series "mm: page_alloc: freelist migratetype hygiene"
Johannes Weiner has fixed the page allocator's handling of
migratetype requests, with resulting improvements in compaction
efficiency.
- In the series "make the hugetlb migration strategy consistent"
Baolin Wang has fixed a hugetlb migration issue, which should
improve hugetlb allocation reliability.
- Liu Shixin has hit an I/O meltdown caused by readahead in a
memory-tight memcg. Addressed in the series "Fix I/O high when
memory almost met memcg limit".
- In the series "mm/filemap: optimize folio adding and splitting"
Kairui Song has optimized pagecache insertion, yielding ~10%
performance improvement in one test.
- Baoquan He has cleaned up and consolidated the early zone
initialization code in the series "mm/mm_init.c: refactor
free_area_init_core()".
- Baoquan has also redone some MM initializatio code in the series
"mm/init: minor clean up and improvement".
- MM helper cleanups from Christoph Hellwig in his series "remove
follow_pfn".
- More cleanups from Matthew Wilcox in the series "Various
page->flags cleanups".
- Vlastimil Babka has contributed maintainability improvements in the
series "memcg_kmem hooks refactoring".
- More folio conversions and cleanups in Matthew Wilcox's series:
"Convert huge_zero_page to huge_zero_folio"
"khugepaged folio conversions"
"Remove page_idle and page_young wrappers"
"Use folio APIs in procfs"
"Clean up __folio_put()"
"Some cleanups for memory-failure"
"Remove page_mapping()"
"More folio compat code removal"
- David Hildenbrand chipped in with "fs/proc/task_mmu: convert
hugetlb functions to work on folis".
- Code consolidation and cleanup work related to GUP's handling of
hugetlbs in Peter Xu's series "mm/gup: Unify hugetlb, part 2".
- Rick Edgecombe has developed some fixes to stack guard gaps in the
series "Cover a guard gap corner case".
- Jinjiang Tu has fixed KSM's behaviour after a fork+exec in the
series "mm/ksm: fix ksm exec support for prctl".
- Baolin Wang has implemented NUMA balancing for multi-size THPs.
This is a simple first-cut implementation for now. The series is
"support multi-size THP numa balancing".
- Cleanups to vma handling helper functions from Matthew Wilcox in
the series "Unify vma_address and vma_pgoff_address".
- Some selftests maintenance work from Dev Jain in the series
"selftests/mm: mremap_test: Optimizations and style fixes".
- Improvements to the swapping of multi-size THPs from Ryan Roberts
in the series "Swap-out mTHP without splitting".
- Kefeng Wang has significantly optimized the handling of arm64's
permission page faults in the series
"arch/mm/fault: accelerate pagefault when badaccess"
"mm: remove arch's private VM_FAULT_BADMAP/BADACCESS"
- GUP cleanups from David Hildenbrand in "mm/gup: consistently call
it GUP-fast".
- hugetlb fault code cleanups from Vishal Moola in "Hugetlb fault
path to use struct vm_fault".
- selftests build fixes from John Hubbard in the series "Fix
selftests/mm build without requiring "make headers"".
- Memory tiering fixes/improvements from Ho-Ren (Jack) Chuang in the
series "Improved Memory Tier Creation for CPUless NUMA Nodes".
Fixes the initialization code so that migration between different
memory types works as intended.
- David Hildenbrand has improved follow_pte() and fixed an errant
driver in the series "mm: follow_pte() improvements and acrn
follow_pte() fixes".
- David also did some cleanup work on large folio mapcounts in his
series "mm: mapcount for large folios + page_mapcount() cleanups".
- Folio conversions in KSM in Alex Shi's series "transfer page to
folio in KSM".
- Barry Song has added some sysfs stats for monitoring multi-size
THP's in the series "mm: add per-order mTHP alloc and swpout
counters".
- Some zswap cleanups from Yosry Ahmed in the series "zswap
same-filled and limit checking cleanups".
- Matthew Wilcox has been looking at buffer_head code and found the
documentation to be lacking. The series is "Improve buffer head
documentation".
- Multi-size THPs get more work, this time from Lance Yang. His
series "mm/madvise: enhance lazyfreeing with mTHP in madvise_free"
optimizes the freeing of these things.
- Kemeng Shi has added more userspace-visible writeback
instrumentation in the series "Improve visibility of writeback".
- Kemeng Shi then sent some maintenance work on top in the series
"Fix and cleanups to page-writeback".
- Matthew Wilcox reduces mmap_lock traffic in the anon vma code in
the series "Improve anon_vma scalability for anon VMAs". Intel's
test bot reported an improbable 3x improvement in one test.
- SeongJae Park adds some DAMON feature work in the series
"mm/damon: add a DAMOS filter type for page granularity access recheck"
"selftests/damon: add DAMOS quota goal test"
- Also some maintenance work in the series
"mm/damon/paddr: simplify page level access re-check for pageout"
"mm/damon: misc fixes and improvements"
- David Hildenbrand has disabled some known-to-fail selftests ni the
series "selftests: mm: cow: flag vmsplice() hugetlb tests as
XFAIL".
- memcg metadata storage optimizations from Shakeel Butt in "memcg:
reduce memory consumption by memcg stats".
- DAX fixes and maintenance work from Vishal Verma in the series
"dax/bus.c: Fixups for dax-bus locking""
* tag 'mm-stable-2024-05-17-19-19' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (426 commits)
memcg, oom: cleanup unused memcg_oom_gfp_mask and memcg_oom_order
selftests/mm: hugetlb_madv_vs_map: avoid test skipping by querying hugepage size at runtime
mm/hugetlb: add missing VM_FAULT_SET_HINDEX in hugetlb_wp
mm/hugetlb: add missing VM_FAULT_SET_HINDEX in hugetlb_fault
selftests: cgroup: add tests to verify the zswap writeback path
mm: memcg: make alloc_mem_cgroup_per_node_info() return bool
mm/damon/core: fix return value from damos_wmark_metric_value
mm: do not update memcg stats for NR_{FILE/SHMEM}_PMDMAPPED
selftests: cgroup: remove redundant enabling of memory controller
Docs/mm/damon/maintainer-profile: allow posting patches based on damon/next tree
Docs/mm/damon/maintainer-profile: change the maintainer's timezone from PST to PT
Docs/mm/damon/design: use a list for supported filters
Docs/admin-guide/mm/damon/usage: fix wrong schemes effective quota update command
Docs/admin-guide/mm/damon/usage: fix wrong example of DAMOS filter matching sysfs file
selftests/damon: classify tests for functionalities and regressions
selftests/damon/_damon_sysfs: use 'is' instead of '==' for 'None'
selftests/damon/_damon_sysfs: find sysfs mount point from /proc/mounts
selftests/damon/_damon_sysfs: check errors from nr_schemes file reads
mm/damon/core: initialize ->esz_bp from damos_quota_init_priv()
selftests/damon: add a test for DAMOS quota goal
...
Both nbd_send_cmd() and nbd_handle_cmd() return either a negative error
number or a positive blk_status_t value. nbd_queue_rq() converts these
return values into a blk_status_t value. There is a bug in the conversion
code: if nbd_send_cmd() returns BLK_STS_RESOURCE, nbd_queue_rq() should
return BLK_STS_RESOURCE instead of BLK_STS_OK. Fix this, move the
conversion code into nbd_handle_cmd() and fix the remaining sparse warnings.
This patch fixes the following sparse warnings:
drivers/block/nbd.c:673:32: warning: incorrect type in return expression (different base types)
drivers/block/nbd.c:673:32: expected int
drivers/block/nbd.c:673:32: got restricted blk_status_t [usertype]
drivers/block/nbd.c:714:48: warning: incorrect type in return expression (different base types)
drivers/block/nbd.c:714:48: expected int
drivers/block/nbd.c:714:48: got restricted blk_status_t [usertype]
drivers/block/nbd.c:1120:21: warning: incorrect type in assignment (different base types)
drivers/block/nbd.c:1120:21: expected int [assigned] ret
drivers/block/nbd.c:1120:21: got restricted blk_status_t [usertype]
drivers/block/nbd.c:1125:16: warning: incorrect type in return expression (different base types)
drivers/block/nbd.c:1125:16: expected restricted blk_status_t
drivers/block/nbd.c:1125:16: got int [assigned] ret
Cc: Christoph Hellwig <hch@lst.de>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Yu Kuai <yukuai3@huawei.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Fixes: fc17b6534e ("blk-mq: switch ->queue_rq return value to blk_status_t")
Cc: stable@vger.kernel.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240510202313.25209-6-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_rq_bytes() returns an unsigned int while 'size' has type unsigned long.
This is confusing. Improve code readability by removing the local variable
'size'.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Yu Kuai <yukuai3@huawei.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240510202313.25209-5-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Document locking assumptions with lockdep_assert_held() instead of source
code comments. The advantage of lockdep_assert_held() is that it is
verified at runtime if lockdep is enabled in the kernel config.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Yu Kuai <yukuai3@huawei.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240510202313.25209-4-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In Linux kernel code it is preferred not to use a cast when converting a
void pointer to another pointer type.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Yu Kuai <yukuai3@huawei.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240510202313.25209-3-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The ramdisk memory utilization can only go up when data is written to
new pages. Implement discard to provide the possibility to reduce memory
usage for pages no longer in use. Aligned discards will free the
associated pages, if any, and determinisitically return zeroed data
until written again.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20240429102308.147627-1-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix the following sparse warnings:
drivers/block/null_blk/main.c:1243:35: warning: incorrect type in return expression (different base types)
drivers/block/null_blk/main.c:1243:35: expected int
drivers/block/null_blk/main.c:1243:35: got restricted blk_status_t
drivers/block/null_blk/main.c:1291:30: warning: incorrect type in return expression (different base types)
drivers/block/null_blk/main.c:1291:30: expected restricted blk_status_t
drivers/block/null_blk/main.c:1291:30: got int
Cc: Christoph Hellwig <hch@lst.de>
Cc: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240510201816.24921-1-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
By default, this will be 511, as that's the block layer default. But
drivers these days can support memory alignments that aren't tied to
the sector sizes, instead just being limited by what the DMA engine
supports. An example is NVMe, where it's generally set to a 32-bit or
64-bit boundary. As ublk itself doesn't really care, just set it low
enough that we don't run into issues with NVMe where the required
O_DIRECT memory alignment is now more restrictive on ublk than it is
on the underlying device.
This was triggered by spurious -EINVAL returns on O_DIRECT IO on a
setup with ublk managing NVMe devices, which previously worked just
fine on the NVMe device itself. With the alignment relaxed, the test
works fine.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=HnjE
-----END PGP SIGNATURE-----
Merge tag 'for-6.10/block-20240511' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- Add a partscan attribute in sysfs, fixing an issue with systemd
relying on an internal interface that went away.
- Attempt #2 at making long running discards interruptible. The
previous attempt went into 6.9, but we ended up mostly reverting it
as it had issues.
- Remove old ida_simple API in bcache
- Support for zoned write plugging, greatly improving the performance
on zoned devices.
- Remove the old throttle low interface, which has been experimental
since 2017 and never made it beyond that and isn't being used.
- Remove page->index debugging checks in brd, as it hasn't caught
anything and prepares us for removing in struct page.
- MD pull request from Song
- Don't schedule block workers on isolated CPUs
* tag 'for-6.10/block-20240511' of git://git.kernel.dk/linux: (84 commits)
blk-throttle: delay initialization until configuration
blk-throttle: remove CONFIG_BLK_DEV_THROTTLING_LOW
block: fix that util can be greater than 100%
block: support to account io_ticks precisely
block: add plug while submitting IO
bcache: fix variable length array abuse in btree_iter
bcache: Remove usage of the deprecated ida_simple_xx() API
md: Revert "md: Fix overflow in is_mddev_idle"
blk-lib: check for kill signal in ioctl BLKDISCARD
block: add a bio_await_chain helper
block: add a blk_alloc_discard_bio helper
block: add a bio_chain_and_submit helper
block: move discard checks into the ioctl handler
block: remove the discard_granularity check in __blkdev_issue_discard
block/ioctl: prefer different overflow check
null_blk: Fix the WARNING: modpost: missing MODULE_DESCRIPTION()
block: fix and simplify blkdevparts= cmdline parsing
block: refine the EOF check in blkdev_iomap_begin
block: add a partscan sysfs attribute for disks
block: add a disk_has_partscan helper
...
1) it doesn't make any sense to have ->open() call set_blocksize() on the
device being opened - the caller will override that anyway.
2) setting block size on underlying device, OTOH, ought to be done when
we are opening it exclusive - i.e. as part of pkt_open_dev(). Having
it done at setup time doesn't guarantee us anything about the state
at the time we start talking to it. Worse, if you happen to have
the underlying device containing e.g. ext2 with 4Kb blocks that
is currently mounted r/o, that set_blocksize() will confuse the hell
out of filesystem.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
ublk_drv currently creates block devices with the default max_segments
and max_segment_size limits of BLK_MAX_SEGMENTS (128) and
BLK_MAX_SEGMENT_SIZE (65536) respectively. These defaults can
artificially constrain the I/O size seen by the ublk server - for
example, suppose that the ublk server has configured itself to accept
I/Os up to 1M and the application is also issuing 1M sized I/Os. If the
I/O buffer used by the application is backed by 4K pages, the buffer
could consist of up to 1M / 4K = 256 physically discontiguous segments
(even if the buffer is virtually contiguous). As such, the I/O could
exceed the default max_segments limit and get split. This can cause
unnecessary performance issues if the ublk server is optimized to handle
1M I/Os. The block layer's segment count/size limits exist to model
hardware constraints which don't exist in ublk_drv's case, so just
remove those limits for the block devices created by ublk_drv.
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: Riley Thomasson <riley@purestorage.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240430211623.2802036-1-ushankar@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Introduce "max_pages" param to recompress device attribute which sets an
upper limit on the number of entries (pages) zram attempts to recompress
(in this particular recompression call). S/W recompression can be quite
expensive so limiting the number of pages recompress touches can be quite
helpful.
Link: https://lkml.kernel.org/r/20240329094050.2815699-1-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Brian Geffon <bgeffon@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When a mutex lock is not used any more, the function mutex_destroy
should be called to mark the mutex lock uninitialized.
Fixes: f2298c0403 ("null_blk: multi queue aware block test driver")
Signed-off-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Link: https://lore.kernel.org/r/20240425171635.4227-1-yanjun.zhu@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In null_zone_write, we do not need to first check if the target zone
condition is FULL, READONLY or OFFLINE: for theses conditions, the check
of the command sector against the zone write pointer will always result
in the command failing. Remove these checks.
We still however need to check that the target zone write pointer is not
invalid for zone append operations. To do so, add the macro
NULL_ZONE_INVALID_WP and use it in null_set_zone_cond() when changing a
zone to READONLY or OFFLINE condition.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20240411085502.728558-4-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For zoned null_blk devices setup without any limit on the maximum number
of open and active zones, there is no need to count the number of zones
that are implicitly open, explicitly open and closed. This is indicated
by the boolean field need_zone_res_mgmt of sturct nullb_device.
Modify the zone management functions null_reset_zone(),
null_finish_zone(), null_open_zone() and null_close_zone() to manage
the zone condition counters only if the device need_zone_res_mgmt field
is true. With this change, the function __null_close_zone() is removed
and integrated into the 2 caller sites directly, with the
null_close_imp_open_zone() call site greatly simplified as this function
closes zones that are known to be in the implicit open condition.
null_zone_write() is modified in a similar manner to do zone condition
accouting only when the device need_zone_res_mgmt field is true.
With these changes, the inline helpers null_lock_zone_res() and
null_unlock_zone_res() are removed and replaced with direct calls to
spin_lock()/spin_unlock().
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240411085502.728558-3-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Modify the null_handle_flush() and null_handle_rq() functions to return
a blk_status_t instead of an errno to simplify the call sites of these
functions and to be consistant with other null_handle_xxx() functions.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Nitesh Shetty <nj.shetty@samsung.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20240411085502.728558-2-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The only user of blk_revalidate_disk_zones() second argument was the
SCSI disk driver (sd). Now that this driver does not require this
update_driver_data argument, remove it to simplify the interface of
blk_revalidate_disk_zones(). Also update the function kdoc comment to
be more accurate (i.e. there is no gendisk ->revalidate method).
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Hans Holmberg <hans.holmberg@wdc.com>
Tested-by: Dennis Maisenbacher <dennis.maisenbacher@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240408014128.205141-21-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add the fua configfs attribute and module parameter to allow
configuring if the device supports FUA or not. Using this attribute
has an effect on the null_blk device only if memory backing is enabled
together with a write cache (cache_size option).
This new attribute allows configuring a null_blk device with a write
cache but without FUA support. This is convenient to test the block
layer flush machinery.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Tested-by: Hans Holmberg <hans.holmberg@wdc.com>
Tested-by: Dennis Maisenbacher <dennis.maisenbacher@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240408014128.205141-18-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add the zone_append_max_sectors configfs attribute and module parameter
to allow configuring the maximum number of 512B sectors of zone append
operations. This attribute is meaningful only for zoned null block
devices.
If not specified, the default is unchanged and the zoned device max
append sectors limit is set to the device max sectors limit.
If a non 0 value is used for this attribute, which is the default,
then native support for zone append operations is enabled.
Setting a 0 value disables native zone append operations support to
instead use the block layer emulation.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Hans Holmberg <hans.holmberg@wdc.com>
Tested-by: Dennis Maisenbacher <dennis.maisenbacher@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240408014128.205141-17-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With zone write plugging enabled at the block layer level, a zoned
device can only ever see at most a single write operation per zone.
There is thus no need to request a block scheduler with strick per-zone
sequential write ordering control through the ELEVATOR_F_ZBD_SEQ_WRITE
feature. Removing this allows using a zoned null_blk device with any
scheduler, including "none".
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Tested-by: Hans Holmberg <hans.holmberg@wdc.com>
Tested-by: Dennis Maisenbacher <dennis.maisenbacher@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240408014128.205141-16-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With zone write plugging enabled at the block layer level, any zone
device can only ever see at most a single write operation per zone.
There is thus no need to request a block scheduler with strick per-zone
sequential write ordering control through the ELEVATOR_F_ZBD_SEQ_WRITE
feature. Removing this allows using a zoned ublk device with any
scheduler, including "none".
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Hans Holmberg <hans.holmberg@wdc.com>
Tested-by: Dennis Maisenbacher <dennis.maisenbacher@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240408014128.205141-15-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
These have no clear purpose. This is effectively a revert of commit
bb7462b6fd ("vfs: use helpers for calling f_op->{read,write}_iter()").
The patch was created with the help of a coccinelle script.
Fixes: bb7462b6fd ("vfs: use helpers for calling f_op->{read,write}_iter()")
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In null_add_dev(), if an error happen after initializing the resources
for a zoned null block device, we must free these resources before
exiting the function. To ensure this, move the out_cleanup_zone label
after out_cleanup_disk as we jump to this latter label if an error
happens after calling null_init_zoned_dev().
Fixes: e440626b1c ("null_blk: pass queue_limits to blk_mq_alloc_disk")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240330005300.1503252-1-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This debugging check will become more costly in the future when we shrink
struct page. It has not proven to be useful, so simply remove it.
This lets us use __xa_insert instead of __xa_cmpxchg() as we no longer
need to know about the page that is currently stored in the XArray.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Link: https://lore.kernel.org/r/20240315181212.2573753-1-willy@infradead.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
duplicated code in redo_fd_request(),
unlock_fdc() function has the same code "do_floppy = NULL" inside.
Signed-off-by: Yufeng Wang <wangyufeng@kylinos.cn>
Suggested-by: Denis Efremov <efremov@linux.com>
Link: https://lore.kernel.org/r/20240319014219.7812-1-wangyufeng@kylinos.cn
Signed-off-by: Jens Axboe <axboe@kernel.dk>
heap optimizations".
- Kuan-Wei Chiu has also sped up the library sorting code in the series
"lib/sort: Optimize the number of swaps and comparisons".
- Alexey Gladkov has added the ability for code running within an IPC
namespace to alter its IPC and MQ limits. The series is "Allow to
change ipc/mq sysctls inside ipc namespace".
- Geert Uytterhoeven has contributed some dhrystone maintenance work in
the series "lib: dhry: miscellaneous cleanups".
- Ryusuke Konishi continues nilfs2 maintenance work in the series
"nilfs2: eliminate kmap and kmap_atomic calls"
"nilfs2: fix kernel bug at submit_bh_wbc()"
- Nathan Chancellor has updated our build tools requirements in the
series "Bump the minimum supported version of LLVM to 13.0.1".
- Muhammad Usama Anjum continues with the selftests maintenance work in
the series "selftests/mm: Improve run_vmtests.sh".
- Oleg Nesterov has done some maintenance work against the signal code
in the series "get_signal: minor cleanups and fix".
Plus the usual shower of singleton patches in various parts of the tree.
Please see the individual changelogs for details.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZfMnvgAKCRDdBJ7gKXxA
jjKMAP4/Upq07D4wjkMVPb+QrkipbbLpdcgJ++q3z6rba4zhPQD+M3SFriIJk/Xh
tKVmvihFxfAhdDthseXcIf1nBjMALwY=
=8rVc
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2024-03-14-09-36' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
- Kuan-Wei Chiu has developed the well-named series "lib min_heap: Min
heap optimizations".
- Kuan-Wei Chiu has also sped up the library sorting code in the series
"lib/sort: Optimize the number of swaps and comparisons".
- Alexey Gladkov has added the ability for code running within an IPC
namespace to alter its IPC and MQ limits. The series is "Allow to
change ipc/mq sysctls inside ipc namespace".
- Geert Uytterhoeven has contributed some dhrystone maintenance work in
the series "lib: dhry: miscellaneous cleanups".
- Ryusuke Konishi continues nilfs2 maintenance work in the series
"nilfs2: eliminate kmap and kmap_atomic calls"
"nilfs2: fix kernel bug at submit_bh_wbc()"
- Nathan Chancellor has updated our build tools requirements in the
series "Bump the minimum supported version of LLVM to 13.0.1".
- Muhammad Usama Anjum continues with the selftests maintenance work in
the series "selftests/mm: Improve run_vmtests.sh".
- Oleg Nesterov has done some maintenance work against the signal code
in the series "get_signal: minor cleanups and fix".
Plus the usual shower of singleton patches in various parts of the tree.
Please see the individual changelogs for details.
* tag 'mm-nonmm-stable-2024-03-14-09-36' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (77 commits)
nilfs2: prevent kernel bug at submit_bh_wbc()
nilfs2: fix failure to detect DAT corruption in btree and direct mappings
ocfs2: enable ocfs2_listxattr for special files
ocfs2: remove SLAB_MEM_SPREAD flag usage
assoc_array: fix the return value in assoc_array_insert_mid_shortcut()
buildid: use kmap_local_page()
watchdog/core: remove sysctl handlers from public header
nilfs2: use div64_ul() instead of do_div()
mul_u64_u64_div_u64: increase precision by conditionally swapping a and b
kexec: copy only happens before uchunk goes to zero
get_signal: don't initialize ksig->info if SIGNAL_GROUP_EXIT/group_exec_task
get_signal: hide_si_addr_tag_bits: fix the usage of uninitialized ksig
get_signal: don't abuse ksig->info.si_signo and ksig->sig
const_structs.checkpatch: add device_type
Normalise "name (ad@dr)" MODULE_AUTHORs to "name <ad@dr>"
dyndbg: replace kstrdup() + strchr() with kstrdup_and_replace()
list: leverage list_is_head() for list_entry_is_head()
nilfs2: MAINTAINERS: drop unreachable project mirror site
smp: make __smp_processor_id() 0-argument macro
fat: fix uninitialized field in nostale filehandles
...
from hotplugged memory rather than only from main memory. Series
"implement "memmap on memory" feature on s390".
- More folio conversions from Matthew Wilcox in the series
"Convert memcontrol charge moving to use folios"
"mm: convert mm counter to take a folio"
- Chengming Zhou has optimized zswap's rbtree locking, providing
significant reductions in system time and modest but measurable
reductions in overall runtimes. The series is "mm/zswap: optimize the
scalability of zswap rb-tree".
- Chengming Zhou has also provided the series "mm/zswap: optimize zswap
lru list" which provides measurable runtime benefits in some
swap-intensive situations.
- And Chengming Zhou further optimizes zswap in the series "mm/zswap:
optimize for dynamic zswap_pools". Measured improvements are modest.
- zswap cleanups and simplifications from Yosry Ahmed in the series "mm:
zswap: simplify zswap_swapoff()".
- In the series "Add DAX ABI for memmap_on_memory", Vishal Verma has
contributed several DAX cleanups as well as adding a sysfs tunable to
control the memmap_on_memory setting when the dax device is hotplugged
as system memory.
- Johannes Weiner has added the large series "mm: zswap: cleanups",
which does that.
- More DAMON work from SeongJae Park in the series
"mm/damon: make DAMON debugfs interface deprecation unignorable"
"selftests/damon: add more tests for core functionalities and corner cases"
"Docs/mm/damon: misc readability improvements"
"mm/damon: let DAMOS feeds and tame/auto-tune itself"
- In the series "mm/mempolicy: weighted interleave mempolicy and sysfs
extension" Rakie Kim has developed a new mempolicy interleaving policy
wherein we allocate memory across nodes in a weighted fashion rather
than uniformly. This is beneficial in heterogeneous memory environments
appearing with CXL.
- Christophe Leroy has contributed some cleanup and consolidation work
against the ARM pagetable dumping code in the series "mm: ptdump:
Refactor CONFIG_DEBUG_WX and check_wx_pages debugfs attribute".
- Luis Chamberlain has added some additional xarray selftesting in the
series "test_xarray: advanced API multi-index tests".
- Muhammad Usama Anjum has reworked the selftest code to make its
human-readable output conform to the TAP ("Test Anything Protocol")
format. Amongst other things, this opens up the use of third-party
tools to parse and process out selftesting results.
- Ryan Roberts has added fork()-time PTE batching of THP ptes in the
series "mm/memory: optimize fork() with PTE-mapped THP". Mainly
targeted at arm64, this significantly speeds up fork() when the process
has a large number of pte-mapped folios.
- David Hildenbrand also gets in on the THP pte batching game in his
series "mm/memory: optimize unmap/zap with PTE-mapped THP". It
implements batching during munmap() and other pte teardown situations.
The microbenchmark improvements are nice.
- And in the series "Transparent Contiguous PTEs for User Mappings" Ryan
Roberts further utilizes arm's pte's contiguous bit ("contpte
mappings"). Kernel build times on arm64 improved nicely. Ryan's series
"Address some contpte nits" provides some followup work.
- In the series "mm/hugetlb: Restore the reservation" Breno Leitao has
fixed an obscure hugetlb race which was causing unnecessary page faults.
He has also added a reproducer under the selftest code.
- In the series "selftests/mm: Output cleanups for the compaction test",
Mark Brown did what the title claims.
- Kinsey Ho has added the series "mm/mglru: code cleanup and refactoring".
- Even more zswap material from Nhat Pham. The series "fix and extend
zswap kselftests" does as claimed.
- In the series "Introduce cpu_dcache_is_aliasing() to fix DAX
regression" Mathieu Desnoyers has cleaned up and fixed rather a mess in
our handling of DAX on archiecctures which have virtually aliasing data
caches. The arm architecture is the main beneficiary.
- Lokesh Gidra's series "per-vma locks in userfaultfd" provides dramatic
improvements in worst-case mmap_lock hold times during certain
userfaultfd operations.
- Some page_owner enhancements and maintenance work from Oscar Salvador
in his series
"page_owner: print stacks and their outstanding allocations"
"page_owner: Fixup and cleanup"
- Uladzislau Rezki has contributed some vmalloc scalability improvements
in his series "Mitigate a vmap lock contention". It realizes a 12x
improvement for a certain microbenchmark.
- Some kexec/crash cleanup work from Baoquan He in the series "Split
crash out from kexec and clean up related config items".
- Some zsmalloc maintenance work from Chengming Zhou in the series
"mm/zsmalloc: fix and optimize objects/page migration"
"mm/zsmalloc: some cleanup for get/set_zspage_mapping()"
- Zi Yan has taught the MM to perform compaction on folios larger than
order=0. This a step along the path to implementaton of the merging of
large anonymous folios. The series is named "Enable >0 order folio
memory compaction".
- Christoph Hellwig has done quite a lot of cleanup work in the
pagecache writeback code in his series "convert write_cache_pages() to
an iterator".
- Some modest hugetlb cleanups and speedups in Vishal Moola's series
"Handle hugetlb faults under the VMA lock".
- Zi Yan has changed the page splitting code so we can split huge pages
into sizes other than order-0 to better utilize large folios. The
series is named "Split a folio to any lower order folios".
- David Hildenbrand has contributed the series "mm: remove
total_mapcount()", a cleanup.
- Matthew Wilcox has sought to improve the performance of bulk memory
freeing in his series "Rearrange batched folio freeing".
- Gang Li's series "hugetlb: parallelize hugetlb page init on boot"
provides large improvements in bootup times on large machines which are
configured to use large numbers of hugetlb pages.
- Matthew Wilcox's series "PageFlags cleanups" does that.
- Qi Zheng's series "minor fixes and supplement for ptdesc" does that
also. S390 is affected.
- Cleanups to our pagemap utility functions from Peter Xu in his series
"mm/treewide: Replace pXd_large() with pXd_leaf()".
- Nico Pache has fixed a few things with our hugepage selftests in his
series "selftests/mm: Improve Hugepage Test Handling in MM Selftests".
- Also, of course, many singleton patches to many things. Please see
the individual changelogs for details.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZfJpPQAKCRDdBJ7gKXxA
joxeAP9TrcMEuHnLmBlhIXkWbIR4+ki+pA3v+gNTlJiBhnfVSgD9G55t1aBaRplx
TMNhHfyiHYDTx/GAV9NXW84tasJSDgA=
=TG55
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2024-03-13-20-04' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- Sumanth Korikkar has taught s390 to allocate hotplug-time page frames
from hotplugged memory rather than only from main memory. Series
"implement "memmap on memory" feature on s390".
- More folio conversions from Matthew Wilcox in the series
"Convert memcontrol charge moving to use folios"
"mm: convert mm counter to take a folio"
- Chengming Zhou has optimized zswap's rbtree locking, providing
significant reductions in system time and modest but measurable
reductions in overall runtimes. The series is "mm/zswap: optimize the
scalability of zswap rb-tree".
- Chengming Zhou has also provided the series "mm/zswap: optimize zswap
lru list" which provides measurable runtime benefits in some
swap-intensive situations.
- And Chengming Zhou further optimizes zswap in the series "mm/zswap:
optimize for dynamic zswap_pools". Measured improvements are modest.
- zswap cleanups and simplifications from Yosry Ahmed in the series
"mm: zswap: simplify zswap_swapoff()".
- In the series "Add DAX ABI for memmap_on_memory", Vishal Verma has
contributed several DAX cleanups as well as adding a sysfs tunable to
control the memmap_on_memory setting when the dax device is
hotplugged as system memory.
- Johannes Weiner has added the large series "mm: zswap: cleanups",
which does that.
- More DAMON work from SeongJae Park in the series
"mm/damon: make DAMON debugfs interface deprecation unignorable"
"selftests/damon: add more tests for core functionalities and corner cases"
"Docs/mm/damon: misc readability improvements"
"mm/damon: let DAMOS feeds and tame/auto-tune itself"
- In the series "mm/mempolicy: weighted interleave mempolicy and sysfs
extension" Rakie Kim has developed a new mempolicy interleaving
policy wherein we allocate memory across nodes in a weighted fashion
rather than uniformly. This is beneficial in heterogeneous memory
environments appearing with CXL.
- Christophe Leroy has contributed some cleanup and consolidation work
against the ARM pagetable dumping code in the series "mm: ptdump:
Refactor CONFIG_DEBUG_WX and check_wx_pages debugfs attribute".
- Luis Chamberlain has added some additional xarray selftesting in the
series "test_xarray: advanced API multi-index tests".
- Muhammad Usama Anjum has reworked the selftest code to make its
human-readable output conform to the TAP ("Test Anything Protocol")
format. Amongst other things, this opens up the use of third-party
tools to parse and process out selftesting results.
- Ryan Roberts has added fork()-time PTE batching of THP ptes in the
series "mm/memory: optimize fork() with PTE-mapped THP". Mainly
targeted at arm64, this significantly speeds up fork() when the
process has a large number of pte-mapped folios.
- David Hildenbrand also gets in on the THP pte batching game in his
series "mm/memory: optimize unmap/zap with PTE-mapped THP". It
implements batching during munmap() and other pte teardown
situations. The microbenchmark improvements are nice.
- And in the series "Transparent Contiguous PTEs for User Mappings"
Ryan Roberts further utilizes arm's pte's contiguous bit ("contpte
mappings"). Kernel build times on arm64 improved nicely. Ryan's
series "Address some contpte nits" provides some followup work.
- In the series "mm/hugetlb: Restore the reservation" Breno Leitao has
fixed an obscure hugetlb race which was causing unnecessary page
faults. He has also added a reproducer under the selftest code.
- In the series "selftests/mm: Output cleanups for the compaction
test", Mark Brown did what the title claims.
- Kinsey Ho has added the series "mm/mglru: code cleanup and
refactoring".
- Even more zswap material from Nhat Pham. The series "fix and extend
zswap kselftests" does as claimed.
- In the series "Introduce cpu_dcache_is_aliasing() to fix DAX
regression" Mathieu Desnoyers has cleaned up and fixed rather a mess
in our handling of DAX on archiecctures which have virtually aliasing
data caches. The arm architecture is the main beneficiary.
- Lokesh Gidra's series "per-vma locks in userfaultfd" provides
dramatic improvements in worst-case mmap_lock hold times during
certain userfaultfd operations.
- Some page_owner enhancements and maintenance work from Oscar Salvador
in his series
"page_owner: print stacks and their outstanding allocations"
"page_owner: Fixup and cleanup"
- Uladzislau Rezki has contributed some vmalloc scalability
improvements in his series "Mitigate a vmap lock contention". It
realizes a 12x improvement for a certain microbenchmark.
- Some kexec/crash cleanup work from Baoquan He in the series "Split
crash out from kexec and clean up related config items".
- Some zsmalloc maintenance work from Chengming Zhou in the series
"mm/zsmalloc: fix and optimize objects/page migration"
"mm/zsmalloc: some cleanup for get/set_zspage_mapping()"
- Zi Yan has taught the MM to perform compaction on folios larger than
order=0. This a step along the path to implementaton of the merging
of large anonymous folios. The series is named "Enable >0 order folio
memory compaction".
- Christoph Hellwig has done quite a lot of cleanup work in the
pagecache writeback code in his series "convert write_cache_pages()
to an iterator".
- Some modest hugetlb cleanups and speedups in Vishal Moola's series
"Handle hugetlb faults under the VMA lock".
- Zi Yan has changed the page splitting code so we can split huge pages
into sizes other than order-0 to better utilize large folios. The
series is named "Split a folio to any lower order folios".
- David Hildenbrand has contributed the series "mm: remove
total_mapcount()", a cleanup.
- Matthew Wilcox has sought to improve the performance of bulk memory
freeing in his series "Rearrange batched folio freeing".
- Gang Li's series "hugetlb: parallelize hugetlb page init on boot"
provides large improvements in bootup times on large machines which
are configured to use large numbers of hugetlb pages.
- Matthew Wilcox's series "PageFlags cleanups" does that.
- Qi Zheng's series "minor fixes and supplement for ptdesc" does that
also. S390 is affected.
- Cleanups to our pagemap utility functions from Peter Xu in his series
"mm/treewide: Replace pXd_large() with pXd_leaf()".
- Nico Pache has fixed a few things with our hugepage selftests in his
series "selftests/mm: Improve Hugepage Test Handling in MM
Selftests".
- Also, of course, many singleton patches to many things. Please see
the individual changelogs for details.
* tag 'mm-stable-2024-03-13-20-04' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (435 commits)
mm/zswap: remove the memcpy if acomp is not sleepable
crypto: introduce: acomp_is_async to expose if comp drivers might sleep
memtest: use {READ,WRITE}_ONCE in memory scanning
mm: prohibit the last subpage from reusing the entire large folio
mm: recover pud_leaf() definitions in nopmd case
selftests/mm: skip the hugetlb-madvise tests on unmet hugepage requirements
selftests/mm: skip uffd hugetlb tests with insufficient hugepages
selftests/mm: dont fail testsuite due to a lack of hugepages
mm/huge_memory: skip invalid debugfs new_order input for folio split
mm/huge_memory: check new folio order when split a folio
mm, vmscan: retry kswapd's priority loop with cache_trim_mode off on failure
mm: add an explicit smp_wmb() to UFFDIO_CONTINUE
mm: fix list corruption in put_pages_list
mm: remove folio from deferred split list before uncharging it
filemap: avoid unnecessary major faults in filemap_fault()
mm,page_owner: drop unnecessary check
mm,page_owner: check for null stack_record before bumping its refcount
mm: swap: fix race between free_swap_and_cache() and swapoff()
mm/treewide: align up pXd_leaf() retval across archs
mm/treewide: drop pXd_large()
...
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCZem4DwAKCRCRxhvAZXjc
ooTRAQDRI6Qz6wJym5Yblta8BScMGbt/SgrdgkoCvT6y83MtqwD+Nv/AZQzi3A3l
9NdULtniW1reuCYkc8R7dYM8S+yAwAc=
=Y1qX
-----END PGP SIGNATURE-----
Merge tag 'vfs-6.9.super' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull block handle updates from Christian Brauner:
"Last cycle we changed opening of block devices, and opening a block
device would return a bdev_handle. This allowed us to implement
support for restricting and forbidding writes to mounted block
devices. It was accompanied by converting and adding helpers to
operate on bdev_handles instead of plain block devices.
That was already a good step forward but ultimately it isn't necessary
to have special purpose helpers for opening block devices internally
that return a bdev_handle.
Fundamentally, opening a block device internally should just be
equivalent to opening files. So now all internal opens of block
devices return files just as a userspace open would. Instead of
introducing a separate indirection into bdev_open_by_*() via struct
bdev_handle bdev_file_open_by_*() is made to just return a struct
file. Opening and closing a block device just becomes equivalent to
opening and closing a file.
This all works well because internally we already have a pseudo fs for
block devices and so opening block devices is simple. There's a few
places where we needed to be careful such as during boot when the
kernel is supposed to mount the rootfs directly without init doing it.
Here we need to take care to ensure that we flush out any asynchronous
file close. That's what we already do for opening, unpacking, and
closing the initramfs. So nothing new here.
The equivalence of opening and closing block devices to regular files
is a win in and of itself. But it also has various other advantages.
We can remove struct bdev_handle completely. Various low-level helpers
are now private to the block layer. Other helpers were simply
removable completely.
A follow-up series that is already reviewed build on this and makes it
possible to remove bdev->bd_inode and allows various clean ups of the
buffer head code as well. All places where we stashed a bdev_handle
now just stash a file and use simple accessors to get to the actual
block device which was already the case for bdev_handle"
* tag 'vfs-6.9.super' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (35 commits)
block: remove bdev_handle completely
block: don't rely on BLK_OPEN_RESTRICT_WRITES when yielding write access
bdev: remove bdev pointer from struct bdev_handle
bdev: make struct bdev_handle private to the block layer
bdev: make bdev_{release, open_by_dev}() private to block layer
bdev: remove bdev_open_by_path()
reiserfs: port block device access to file
ocfs2: port block device access to file
nfs: port block device access to files
jfs: port block device access to file
f2fs: port block device access to files
ext4: port block device access to file
erofs: port device access to file
btrfs: port device access to file
bcachefs: port block device access to file
target: port block device access to file
s390: port block device access to file
nvme: port block device access to file
block2mtd: port device access to files
bcache: port block device access to files
...
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/a00aea8201ea85ae726411bb0fb015ea026ff40a.1709886922.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Found with git grep 'MODULE_AUTHOR(".*([^)]*@'
Fixed with
sed -i '/MODULE_AUTHOR(".*([^)]*@/{s/ (/ </g;s/)"/>"/;s/)and/> and/}' \
$(git grep -l 'MODULE_AUTHOR(".*([^)]*@')
Also:
in drivers/media/usb/siano/smsusb.c normalise ", INC" to ", Inc";
this is what every other MODULE_AUTHOR for this company says,
and it's what the header says
in drivers/sbus/char/openprom.c normalise a double-spaced separator;
this is clearly copied from the copyright header,
where the names are aligned on consecutive lines thusly:
* Linux/SPARC PROM Configuration Driver
* Copyright (C) 1996 Thomas K. Dyas (tdyas@noc.rutgers.edu)
* Copyright (C) 1996 Eddie C. Dost (ecd@skynet.be)
but the authorship branding is single-line
Link: https://lkml.kernel.org/r/mk3geln4azm5binjjlfsgjepow4o73domjv6ajybws3tz22vb3@tarta.nabijaczleweli.xyz
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
In virtblk_read_zoned_limits(), setting a zoned block device maximum
number of open and active zones using the functions
disk_set_max_open_zones() and disk_set_max_active_zones() is incorrect
as setting the limits for the request queue is now done atomically when
the gendisk is created (with blk_mq_alloc_disk()). The value set by the
disk_set_max_open/active_zones() functions will be overwritten.
Fix this by setting the maximum number of open and active zones directly
in the queue_limits structure passed to virtblk_read_zoned_limits().
Fixes: 8b83725656 ("virtio_blk: pass queue_limits to blk_mq_alloc_disk")
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20240301192639.410183-2-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch is against CVE-2023-6270. The description of cve is:
A flaw was found in the ATA over Ethernet (AoE) driver in the Linux
kernel. The aoecmd_cfg_pkts() function improperly updates the refcnt on
`struct net_device`, and a use-after-free can be triggered by racing
between the free on the struct and the access through the `skbtxq`
global queue. This could lead to a denial of service condition or
potential code execution.
In aoecmd_cfg_pkts(), it always calls dev_put(ifp) when skb initial
code is finished. But the net_device ifp will still be used in
later tx()->dev_queue_xmit() in kthread. Which means that the
dev_put(ifp) should NOT be called in the success path of skb
initial code in aoecmd_cfg_pkts(). Otherwise tx() may run into
use-after-free because the net_device is freed.
This patch removed the dev_put(ifp) in the success path in
aoecmd_cfg_pkts(), and added dev_put() after skb xmit in tx().
Link: https://nvd.nist.gov/vuln/detail/CVE-2023-6270
Fixes: 7562f876cd ("[NET]: Rework dev_base via list_head (v3)")
Signed-off-by: Chun-Yi Lee <jlee@suse.com>
Link: https://lore.kernel.org/r/20240305082048.25526-1-jlee@suse.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Switch drbd_reconsider_queue_parameters to set up the queue parameters
in an on-stack queue_limits structure and apply the atomically. Remove
various helpers that have become so trivial that they can be folded into
drbd_reconsider_queue_parameters.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240305134041.137006-8-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a helper to check if discard is supported for a given connection /
backing device combination.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Philipp Reisner <philipp.reisner@linbit.com>
Reviewed-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Tested-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20240306140332.623759-7-philipp.reisner@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
fixup_write_zeroes always overrides the max_write_zeroes_sectors value
a little further down the callchain, so don't bother to setup a limit
in decide_on_discard_support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Philipp Reisner <philipp.reisner@linbit.com>
Reviewed-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Tested-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20240306140332.623759-6-philipp.reisner@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
drbd_setup_queue_param is only called by drbd_reconsider_queue_parameters
and there is no really clear boundary of responsibilities between the
two.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Philipp Reisner <philipp.reisner@linbit.com>
Reviewed-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Tested-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20240306140332.623759-5-philipp.reisner@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Factor out a drbd_backing_dev_max_segments helper that checks the
backing device limitation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Philipp Reisner <philipp.reisner@linbit.com>
Reviewed-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Tested-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20240306140332.623759-4-philipp.reisner@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Split out a drbd_max_peer_bio_size helper for the peer I/O size,
and condense the various checks to a nested min3(..., max())) instead
of using a lot of local variables.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240305134041.137006-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass a queue_limits structure with the max_hw_sectors limit to
blk_alloc_disk instead of updating the limit on the allocated gendisk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240305134041.137006-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use queue_limits_start_update / queue_limits_commit_update to update
all the limits in one go and with proper sanity checking.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240229143846.1047223-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
nbd currently updates the logical and physical block sizes as well
as the discard_sectors on a live queue. Freeze the queue first to
make sure there are not commands in flight that can see torn or
inconsistent limits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240229143846.1047223-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
nbd_config_put currently clears discard_sectors when unusing a device.
This is pretty odd behavior and different from the sector size
configuration which is simply left in places and then reconfigured when
nbd_set_size is as part of configuring the device. Change nbd_set_size
to clear discard_sectors if discard is not supported so that all the
queue limits changes are handled in one place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240229143846.1047223-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
pktcdvd sets max_hw_sectors on the queue of the underlying device that
it doesn't own (and doesn't reset it ever) since the driver was merged.
This can create all kinds of problems as the underlying driver doesn't
even know about it changing the limit.
As the state purpose is to not create I/Os larger than a single frame,
and pktcdvd never builds bios larger than that, just set REQ_NOMERGE
on the bios it submits so that largers I/Os never get built.
Note: I don't have packet writing hardware, so this is compile tested
only.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240229144408.1047967-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The current command UBLK_CMD_DEL_DEV won't return until the device is
released, this way looks more reliable, but makes userspace more
difficult to implement, especially about orders: unmap command
buffer(which holds one ublkc reference), ublkc close,
io_uring_file_unregister, ublkb close.
Add UBLK_CMD_DEL_DEV_ASYNC so that device deletion won't wait release,
then userspace needn't worry about the above order. Actually both loop
and nbd is deleted in this async way.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240223075539.89945-3-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Firstly convert get_device() and put_device() into ublk_get_device()
and ublk_put_device().
Secondly annotate ublk_get_device() & ublk_put_device() as noinline
for trace, especially it is often to trigger device deletion hang
when incorrect order is used on ublkc mmap, ublkc close,
io_uring_sqe_unregister_file, ublkb close.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240223075539.89945-2-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the initial queue limits to blk_mq_alloc_disk and use the
blkif_set_queue_limits API to update the limits on reconnect.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Link: https://lore.kernel.org/r/20240221125845.3610668-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blkif_set_queue_limits already sets the max_sements limits, so don't do
it a second time. Also remove a comment about a long fixe bug in
blk_mq_update_nr_hw_queues.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Link: https://lore.kernel.org/r/20240221125845.3610668-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The block layer now sets the discard granularity to the physical
block size default. Take advantage of that in xen-blkfront and only
set the discard granularity if explicitly specified.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Link: https://lore.kernel.org/r/20240221125845.3610668-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently xen-blkfront set the max discard limit to the capacity of
the device, which is suboptimal when the capacity changes. Just set
it to UINT_MAX, which has the same effect and is simpler.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Link: https://lore.kernel.org/r/20240221125845.3610668-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently zram allocates 2 physically contiguous pages per-CPU's
compression stream (we may have up to 4 streams per-CPU). Since those
buffers are per-CPU we allocate them from CPU hotplug path, which may have
higher risks of failed allocations on devices with fragmented memory.
Switch to virtually contiguous allocations - crypto comp does not seem
impose requirements on compression working buffers to be physically
contiguous.
Link: https://lkml.kernel.org/r/20240213065400.6561-1-21cnbao@gmail.com
Signed-off-by: Barry Song <v-songbaohua@oppo.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Some architectures, such as arm, have implemented optimized copy_page for
full page copying.
Replace the full page memcpy with copy_page to take advantage of the
optimization.
Link: https://lkml.kernel.org/r/20231007070554.8657-1-mark-pk.tsai@mediatek.com
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: YJ Chiang <yj.chiang@mediatek.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Since commit 8b631f9cf0 ("null_blk: remove the bio based I/O path"),
struct nullb members queue_depth and nr_queues are only ever written, so
delete them.
With that, null_exit_hctx() can also be deleted.
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240222083420.6026-1-john.g.garry@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The two users can get the private data from the gendisk with one less
pointer dereference, and we can drop the useless q parameter from
pkt_make_request_write.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240222073647.3776769-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the queue limits directly to blk_mq_alloc_disk instead of
setting them one at a time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240220093248.3290292-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
null_gendisk_register isn't a very useful abstraction given that it
doesn't even allocate the gendisk. Merge it into the only caller
instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240220093248.3290292-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the tagset initialization out of null_add_dev into a new
null_setup_tagset helper, and move the shared vs local differences
out of null_init_tag_set into the callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240220093248.3290292-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Otherwise it will be reset to the always same value when initializing a
device using the shared tag_set.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240220093248.3290292-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The bio based I/O path complicates null_blk and also make various
data structures, including the per-command one way bigger than
required for the main request based interface. As the bio-based
path is mostly used by stacking drivers and simple memory based
drivers, and brd is a good example driver for the latter there is
no need to have a bio based path in null_blk. Remove the path
to simplify the driver and make future block layer API changes
simpler by not having to deal with the complex two API setup in
null_blk.
Note that the queue_mode field in struct nullb_device is kept as
that is simpler than having two different places to check the
value and fully open coding the debugfs helpers as the existing
ones won't work without a named struct member.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240220093248.3290292-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the limits ublk imposes directly to blk_mq_alloc_disk instead of
setting them one at a time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240215070300.2200308-17-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the few limits sunvdc imposes directly to blk_mq_alloc_disk instead
of setting them one at a time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240215070300.2200308-10-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the limits rnbd-clt imposes directly to blk_mq_alloc_disk instead
of setting them one at a time.
While at it don't set an explicit number of discard segments, as 1 is
the default (which most drivers rely on).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20240215070300.2200308-9-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the limits rbd imposes directly to blk_mq_alloc_disk instead
of setting them one at a time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240215070300.2200308-8-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the few limits ps3disk imposes directly to blk_mq_alloc_disk instead
of setting them one at a time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240215070300.2200308-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the few limits nbd imposes directly to blk_mq_alloc_disk instead
of setting them one at a time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240215070300.2200308-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the few limits mtip imposes directly to blk_mq_alloc_disk instead
of setting them one at a time and drop the pointless setting of a io_min
that is equal to the physical block size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240215070300.2200308-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the few limits floppy imposes directly to blk_mq_alloc_disk instead
of setting them one at a time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Denis Efremov <efremov@linux.com>
Link: https://lore.kernel.org/r/20240215070300.2200308-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the few limits aoe imposes directly to blk_mq_alloc_disk instead
of setting them one at a time and improve the way the default
max_hw_sectors is initialized while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240215070300.2200308-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the queue limits directly to blk_alloc_disk instead of setting them
one at a time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Link: https://lore.kernel.org/r/20240215071055.2201424-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the queue limits directly to blk_alloc_disk instead of setting them
one at a time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Link: https://lore.kernel.org/r/20240215071055.2201424-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the queue limits directly to blk_alloc_disk instead of setting them
one at a time.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Link: https://lore.kernel.org/r/20240215071055.2201424-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass a queue_limits to blk_alloc_disk and apply it if non-NULL. This
will allow allocating queues with valid queue limits instead of setting
the values one at a time later.
Also change blk_alloc_disk to return an ERR_PTR instead of just NULL
which can't distinguish errors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Link: https://lore.kernel.org/r/20240215071055.2201424-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
nla_nest_start() may fail and return NULL. Insert a check and set errno
based on other call sites within the same source code.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Fixes: 47d902b90a ("nbd: add a status netlink command")
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20240218042534.it.206-kees@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the default limits to blk_mq_alloc_disk and then use the
queue_limits_{start,commit}_update API to change the limits in an
atomic way on existing loop gendisks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240213073425.1621680-16-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass the max_hw_sector limit loop sets at initialization time directly to
blk_mq_alloc_disk instead of updating it right after the allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240213073425.1621680-15-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Initialize the local variables for the discard max sectors and
granularity to zero as a sensible default, and then merge the
calls assigning them to the queue limits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240213073425.1621680-14-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Call virtblk_read_limits and most of virtblk_probe_zoned_device before
allocating the gendisk and thus request_queue and make them read into
a queue_limits structure instead. Pass this initialized queue_limits
to blk_mq_alloc_disk to set the queue up with the right parameters
from the start and only leave a few final touches for zoned devices
to be done just before adding the disk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240213073425.1621680-13-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Split out a virtblk_read_limits helper that just reads the various
queue limits to separate it from the higher level probing logic.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240213073425.1621680-12-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass a queue_limits to blk_mq_alloc_disk and apply it if non-NULL. This
will allow allocating queues with valid queue limits instead of setting
the values one at a time later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240213073425.1621680-11-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are four state machines in drbd that use a common infrastructure, with
a cast to an incompatible function type in REMEMBER_STATE_CHANGE that clang-16
now warns about:
drivers/block/drbd/drbd_state.c:1632:3: error: cast from 'int (*)(struct sk_buff *, unsigned int, struct drbd_resource_state_change *, enum drbd_notification_type)' to 'typeof (last_func)' (aka 'int (*)(struct sk_buff *, unsigned int, void *, enum drbd_notification_type)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1632 | REMEMBER_STATE_CHANGE(notify_resource_state_change,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1633 | resource_state_change, NOTIFY_CHANGE);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/block/drbd/drbd_state.c:1619:17: note: expanded from macro 'REMEMBER_STATE_CHANGE'
1619 | last_func = (typeof(last_func))func; \
| ^~~~~~~~~~~~~~~~~~~~~~~
drivers/block/drbd/drbd_state.c:1641:4: error: cast from 'int (*)(struct sk_buff *, unsigned int, struct drbd_connection_state_change *, enum drbd_notification_type)' to 'typeof (last_func)' (aka 'int (*)(struct sk_buff *, unsigned int, void *, enum drbd_notification_type)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1641 | REMEMBER_STATE_CHANGE(notify_connection_state_change,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1642 | connection_state_change, NOTIFY_CHANGE);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Change these all to actually expect a void pointer to be passed, which
matches the caller.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240213100354.457128-1-arnd@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
clang-16 complains about a control flow integrity (kcfi) violation
casting between incompatible pointers:
drivers/block/floppy.c:2001:11: error: cast from 'void (*)(void)' to 'done_f' (aka 'void (*)(int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
2001 | .done = (done_f)empty
| ^~~~~~~~~~~~~
Just add another empty function with the correct prototype as a
workaround.
The warning is for code that was added before the start of the normal
git history, but I tracked it done to an early change in the reconstructed
linux-history.git.
Fixes: 598a477afe06 ("Import 1.1.41")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240213095918.455478-1-arnd@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=0mLS
-----END PGP SIGNATURE-----
Merge tag 'block-6.8-2024-02-10' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- Update a potentially stale firmware attribute (Maurizio)
- Fixes for the recent verbose error logging (Keith, Chaitanya)
- Protection information payload size fix for passthrough (Francis)
- Fix for a queue freezing issue in virtblk (Yi)
- blk-iocost underflow fix (Tejun)
- blk-wbt task detection fix (Jan)
* tag 'block-6.8-2024-02-10' of git://git.kernel.dk/linux:
virtio-blk: Ensure no requests in virtqueues before deleting vqs.
blk-iocost: Fix an UBSAN shift-out-of-bounds warning
nvme: use ns->head->pi_size instead of t10_pi_tuple structure size
nvme-core: fix comment to reflect right functions
nvme: move passthrough logging attribute to head
blk-wbt: Fix detection of dirty-throttled tasks
nvme-host: fix the updating of the firmware version
Allow setting shared_tags through configfs, which could only be set as a
module parameter. For that purpose, delay tag_set initialization from
null_init() to null_add_dev(). Refer tag_set.ops as the flag to check if
tag_set is initialized or not.
The following parameters can not be set through configfs yet:
timeout
requeue
init_hctx
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20240130042134.2463659-1-shinichiro.kawasaki@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ensure no remaining requests in virtqueues before resetting vdev and
deleting virtqueues. Otherwise these requests will never be completed.
It may cause the system to become unresponsive.
Function blk_mq_quiesce_queue() can ensure that requests have become
in_flight status, but it cannot guarantee that requests have been
processed by the device. Virtqueues should never be deleted before
all requests become complete status.
Function blk_mq_freeze_queue() ensure that all requests in virtqueues
become complete status. And no requests can enter in virtqueues.
Signed-off-by: Yi Sun <yi.sun@unisoc.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Link: https://lore.kernel.org/r/20240129085250.1550594-1-yi.sun@unisoc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that the driver core can properly handle constant struct bus_type,
move the rbd_bus_type variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20240204-bus_cleanup-block-v1-1-fc77afd8d7cc@marliere.net
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=A7z9
-----END PGP SIGNATURE-----
Merge tag 'block-6.8-2024-01-26' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- RCU warning fix for md (Mikulas)
- Fix for an aoe issue that lockdep rightfully complained about
(Maksim)
- Fix for an error code change in partitioning that caused a regression
with some tools (Li)
- Fix for a data direction warning with bi-direction commands
(Christian)
* tag 'block-6.8-2024-01-26' of git://git.kernel.dk/linux:
md: fix a suspicious RCU usage warning
aoe: avoid potential deadlock at set_capacity
block: Fix WARNING in _copy_from_iter
block: Move checking GENHD_FL_NO_PART to bdev_add_partition()
Move set_capacity() outside of the section procected by (&d->lock).
To avoid possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
[1] lock(&bdev->bd_size_lock);
local_irq_disable();
[2] lock(&d->lock);
[3] lock(&bdev->bd_size_lock);
<Interrupt>
[4] lock(&d->lock);
*** DEADLOCK ***
Where [1](&bdev->bd_size_lock) hold by zram_add()->set_capacity().
[2]lock(&d->lock) hold by aoeblk_gdalloc(). And aoeblk_gdalloc()
is trying to acquire [3](&bdev->bd_size_lock) at set_capacity() call.
In this situation an attempt to acquire [4]lock(&d->lock) from
aoecmd_cfg_rsp() will lead to deadlock.
So the simplest solution is breaking lock dependency
[2](&d->lock) -> [3](&bdev->bd_size_lock) by moving set_capacity()
outside.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240124072436.3745720-2-bigunclemax@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The running list is supposed to contain requests that are pinning the
exclusive lock, i.e. those that must be flushed before exclusive lock
is released. When wake_lock_waiters() is called to handle an error,
requests on the acquiring list are failed with that error and no
flushing takes place. Briefly moving them to the running list is not
only pointless but also harmful: if exclusive lock gets acquired
before all of their state machines are scheduled and go through
rbd_lock_del_request(), we trigger
rbd_assert(list_empty(&rbd_dev->running_list));
in rbd_try_acquire_lock().
Cc: stable@vger.kernel.org
Fixes: 637cd06053 ("rbd: new exclusive lock wait/wake code")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().
Note that the upper limit of ida_simple_get() is exclusive, while that
of ida_alloc_max() is inclusive, so 1 has been subtracted.
[ idryomov: tweak changelog ]
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
-----BEGIN PGP SIGNATURE-----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=DLW9
-----END PGP SIGNATURE-----
Merge tag 'for-6.8/block-2024-01-18' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- tcp, fc, and rdma target fixes (Maurizio, Daniel, Hannes,
Christoph)
- discard fixes and improvements (Christoph)
- timeout debug improvements (Keith, Max)
- various cleanups (Daniel, Max, Giuxen)
- trace event string fixes (Arnd)
- shadow doorbell setup on reset fix (William)
- a write zeroes quirk for SK Hynix (Jim)
- MD pull request via Song:
- Sparse warning since v6.0 (Bart)
- /proc/mdstat regression since v6.7 (Yu Kuai)
- Use symbolic error value (Christian)
- IO Priority documentation update (Christian)
- Fix for accessing queue limits without having entered the queue
(Christoph, me)
- Fix for loop dio support (Christoph)
- Move null_blk off deprecated ida interface (Christophe)
- Ensure nbd initializes full msghdr (Eric)
- Fix for a regression with the folio conversion, which is now easier
to hit because of an unrelated change (Matthew)
- Remove redundant check in virtio-blk (Li)
- Fix for a potential hang in sbitmap (Ming)
- Fix for partial zone appending (Damien)
- Misc changes and fixes (Bart, me, Kemeng, Dmitry)
* tag 'for-6.8/block-2024-01-18' of git://git.kernel.dk/linux: (45 commits)
Documentation: block: ioprio: Update schedulers
loop: fix the the direct I/O support check when used on top of block devices
blk-mq: Remove the hctx 'run' debugfs attribute
nbd: always initialize struct msghdr completely
block: Fix iterating over an empty bio with bio_for_each_folio_all
block: bio-integrity: fix kcalloc() arguments order
virtio_blk: remove duplicate check if queue is broken in virtblk_done
sbitmap: remove stale comment in sbq_calc_wake_batch
block: Correct a documentation comment in blk-cgroup.c
null_blk: Remove usage of the deprecated ida_simple_xx() API
block: ensure we hold a queue reference when using queue limits
blk-mq: rename blk_mq_can_use_cached_rq
block: print symbolic error name instead of error code
blk-mq: fix IO hang from sbitmap wakeup race
nvmet-rdma: avoid circular locking dependency on install_queue()
nvmet-tcp: avoid circular locking dependency on install_queue()
nvme-pci: set doorbell config before unquiescing
block: fix partial zone append completion handling in req_bio_endio()
block/iocost: silence warning on 'last_period' potentially being unused
md/raid1: Use blk_opf_t for read and write operations
...
__loop_update_dio only checks the alignment requirement for block backed
file systems, but misses them for the case where the loop device is
created directly on top of another block device. Due to this creating
a loop device with default option plus the direct I/O flag on a > 512 byte
sector size file system will lead to incorrect I/O being submitted to the
lower block device and a lot of error from the lock layer. This can
be seen with xfstests generic/563.
Fix the code in __loop_update_dio by factoring the alignment check into
a helper, and calling that also for the struct block_device of a block
device inode.
Also remove the TODO comment talking about dynamically switching between
buffered and direct I/O, which is a would be a recipe for horrible
performance and occasional data loss.
Fixes: 2e5ab5f379 ("block: loop: prepare for supporing direct IO")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240117175901.871796-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
virtqueue_enable_cb() will call virtqueue_poll() which will check if
queue is broken at beginning, so remove the virtqueue_is_broken() call
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=5v/U
-----END PGP SIGNATURE-----
Merge tag 'for-6.8/io_uring-2024-01-08' of git://git.kernel.dk/linux
Pull io_uring updates from Jens Axboe:
"Mostly just come fixes and cleanups, but one feature as well. In
detail:
- Harden the check for handling IOPOLL based on return (Pavel)
- Various minor optimizations (Pavel)
- Drop remnants of SCM_RIGHTS fd passing support, now that it's no
longer supported since 6.7 (me)
- Fix for a case where bytes_done wasn't initialized properly on a
failure condition for read/write requests (me)
- Move the register related code to a separate file (me)
- Add support for returning the provided ring buffer head (me)
- Add support for adding a direct descriptor to the normal file table
(me, Christian Brauner)
- Fix for ensuring pending task_work for a ring with DEFER_TASKRUN is
run even if we timeout waiting (me)"
* tag 'for-6.8/io_uring-2024-01-08' of git://git.kernel.dk/linux:
io_uring: ensure local task_work is run on wait timeout
io_uring/kbuf: add method for returning provided buffer ring head
io_uring/rw: ensure io->bytes_done is always initialized
io_uring: drop any code related to SCM_RIGHTS
io_uring/unix: drop usage of io_uring socket
io_uring/register: move io_uring_register(2) related code to register.c
io_uring/openclose: add support for IORING_OP_FIXED_FD_INSTALL
io_uring/cmd: inline io_uring_cmd_get_task
io_uring/cmd: inline io_uring_cmd_do_in_task_lazy
io_uring: split out cmd api into a separate header
io_uring: optimise ltimeout for inline execution
io_uring: don't check iopoll if request completes
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAmWcIOIQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpn6hD/9oO7U75PuxUwYYHZ9Uzxpw6gQ0LEmeyJmE
NQYCkfYHVq3IsgOdF7elI9v3qtr6v8V8CdB7cByrnn3DgwsMuiTKZZ0dK7vH37PO
DX+/xn349e8oH7RdRo7f3m95g1YbHfpfnj0Rc4mjTDV72Jr/HlLTVgGTQg8DEnCR
wBIFmeuBHHgeeLh87gsWLAP7ReReiy9V1uqpDFsko2/4BxRAM/8eedkwcAxD8aEy
rd+dT/SBQj2cOdQMUeExT3gWjwzHh6ZHx3f1WCLK5fdck6BogH2hBUeri6F/H98L
HoaXjBZYBTH68hB/mnO5I4g1ZlrVM74Vp7JPa3e1SFFtyEi6lsyrk2J3GoNh0E7r
pXqH5kAcaJwBsBrbRGuvEyGbn9RLTaN5Gvseud0VE4oMruyodTniQaHXuIGackgz
sMavMho4486EUWPaF7gIBdLNK1hO13w+IDZ4+3oBxhudMqdgZbk4iYpOCqQ7QY5G
2vkzAE/sZ+aVNXeaIQOI8dE5clBy8gJ+6+t8dm3DY1r1xdbcnU40iZ8/fri3h69r
vHs9bpQnVWZF0gEyEflY1pkcAPpIkvMmWCR7Ehy5YCkIfa+qfSL05o3dicpWovLP
N+gCtpkhTK2AvmUWsUMypMLRvoSOImyCIiobrr3qNBaUdgRP8xKfUa72RuRp8cGl
Vrj5oAiE3w==
=YAfp
-----END PGP SIGNATURE-----
Merge tag 'for-6.8/block-2024-01-08' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
"Pretty quiet round this time around. This contains:
- NVMe updates via Keith:
- nvme fabrics spec updates (Guixin, Max)
- nvme target udpates (Guixin, Evan)
- nvme attribute refactoring (Daniel)
- nvme-fc numa fix (Keith)
- MD updates via Song:
- Fix/Cleanup RCU usage from conf->disks[i].rdev (Yu Kuai)
- Fix raid5 hang issue (Junxiao Bi)
- Add Yu Kuai as Reviewer of the md subsystem
- Remove deprecated flavors (Song Liu)
- raid1 read error check support (Li Nan)
- Better handle events off-by-1 case (Alex Lyakas)
- Efficiency improvements for passthrough (Kundan)
- Support for mapping integrity data directly (Keith)
- Zoned write fix (Damien)
- rnbd fixes (Kees, Santosh, Supriti)
- Default to a sane discard size granularity (Christoph)
- Make the default max transfer size naming less confusing
(Christoph)
- Remove support for deprecated host aware zoned model (Christoph)
- Misc fixes (me, Li, Matthew, Min, Ming, Randy, liyouhong, Daniel,
Bart, Christoph)"
* tag 'for-6.8/block-2024-01-08' of git://git.kernel.dk/linux: (78 commits)
block: Treat sequential write preferred zone type as invalid
block: remove disk_clear_zoned
sd: remove the !ZBC && blk_queue_is_zoned case in sd_read_block_characteristics
drivers/block/xen-blkback/common.h: Fix spelling typo in comment
blk-cgroup: fix rcu lockdep warning in blkg_lookup()
blk-cgroup: don't use removal safe list iterators
block: floor the discard granularity to the physical block size
mtd_blkdevs: use the default discard granularity
bcache: use the default discard granularity
zram: use the default discard granularity
null_blk: use the default discard granularity
nbd: use the default discard granularity
ubd: use the default discard granularity
block: default the discard granularity to sector size
bcache: discard_granularity should not be smaller than a sector
block: remove two comments in bio_split_discard
block: rename and document BLK_DEF_MAX_SECTORS
loop: don't abuse BLK_DEF_MAX_SECTORS
aoe: don't abuse BLK_DEF_MAX_SECTORS
null_blk: don't cap max_hw_sectors to BLK_DEF_MAX_SECTORS
...
are included in this merge do the following:
- Peng Zhang has done some mapletree maintainance work in the
series
"maple_tree: add mt_free_one() and mt_attr() helpers"
"Some cleanups of maple tree"
- In the series "mm: use memmap_on_memory semantics for dax/kmem"
Vishal Verma has altered the interworking between memory-hotplug
and dax/kmem so that newly added 'device memory' can more easily
have its memmap placed within that newly added memory.
- Matthew Wilcox continues folio-related work (including a few
fixes) in the patch series
"Add folio_zero_tail() and folio_fill_tail()"
"Make folio_start_writeback return void"
"Fix fault handler's handling of poisoned tail pages"
"Convert aops->error_remove_page to ->error_remove_folio"
"Finish two folio conversions"
"More swap folio conversions"
- Kefeng Wang has also contributed folio-related work in the series
"mm: cleanup and use more folio in page fault"
- Jim Cromie has improved the kmemleak reporting output in the
series "tweak kmemleak report format".
- In the series "stackdepot: allow evicting stack traces" Andrey
Konovalov to permits clients (in this case KASAN) to cause
eviction of no longer needed stack traces.
- Charan Teja Kalla has fixed some accounting issues in the page
allocator's atomic reserve calculations in the series "mm:
page_alloc: fixes for high atomic reserve caluculations".
- Dmitry Rokosov has added to the samples/ dorectory some sample
code for a userspace memcg event listener application. See the
series "samples: introduce cgroup events listeners".
- Some mapletree maintanance work from Liam Howlett in the series
"maple_tree: iterator state changes".
- Nhat Pham has improved zswap's approach to writeback in the
series "workload-specific and memory pressure-driven zswap
writeback".
- DAMON/DAMOS feature and maintenance work from SeongJae Park in
the series
"mm/damon: let users feed and tame/auto-tune DAMOS"
"selftests/damon: add Python-written DAMON functionality tests"
"mm/damon: misc updates for 6.8"
- Yosry Ahmed has improved memcg's stats flushing in the series
"mm: memcg: subtree stats flushing and thresholds".
- In the series "Multi-size THP for anonymous memory" Ryan Roberts
has added a runtime opt-in feature to transparent hugepages which
improves performance by allocating larger chunks of memory during
anonymous page faults.
- Matthew Wilcox has also contributed some cleanup and maintenance
work against eh buffer_head code int he series "More buffer_head
cleanups".
- Suren Baghdasaryan has done work on Andrea Arcangeli's series
"userfaultfd move option". UFFDIO_MOVE permits userspace heap
compaction algorithms to move userspace's pages around rather than
UFFDIO_COPY'a alloc/copy/free.
- Stefan Roesch has developed a "KSM Advisor", in the series
"mm/ksm: Add ksm advisor". This is a governor which tunes KSM's
scanning aggressiveness in response to userspace's current needs.
- Chengming Zhou has optimized zswap's temporary working memory
use in the series "mm/zswap: dstmem reuse optimizations and
cleanups".
- Matthew Wilcox has performed some maintenance work on the
writeback code, both code and within filesystems. The series is
"Clean up the writeback paths".
- Andrey Konovalov has optimized KASAN's handling of alloc and
free stack traces for secondary-level allocators, in the series
"kasan: save mempool stack traces".
- Andrey also performed some KASAN maintenance work in the series
"kasan: assorted clean-ups".
- David Hildenbrand has gone to town on the rmap code. Cleanups,
more pte batching, folio conversions and more. See the series
"mm/rmap: interface overhaul".
- Kinsey Ho has contributed some maintenance work on the MGLRU
code in the series "mm/mglru: Kconfig cleanup".
- Matthew Wilcox has contributed lruvec page accounting code
cleanups in the series "Remove some lruvec page accounting
functions".
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZZyF2wAKCRDdBJ7gKXxA
jjWjAP42LHvGSjp5M+Rs2rKFL0daBQsrlvy6/jCHUequSdWjSgEAmOx7bc5fbF27
Oa8+DxGM9C+fwqZ/7YxU2w/WuUmLPgU=
=0NHs
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2024-01-08-15-31' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
"Many singleton patches against the MM code. The patch series which are
included in this merge do the following:
- Peng Zhang has done some mapletree maintainance work in the series
'maple_tree: add mt_free_one() and mt_attr() helpers'
'Some cleanups of maple tree'
- In the series 'mm: use memmap_on_memory semantics for dax/kmem'
Vishal Verma has altered the interworking between memory-hotplug
and dax/kmem so that newly added 'device memory' can more easily
have its memmap placed within that newly added memory.
- Matthew Wilcox continues folio-related work (including a few fixes)
in the patch series
'Add folio_zero_tail() and folio_fill_tail()'
'Make folio_start_writeback return void'
'Fix fault handler's handling of poisoned tail pages'
'Convert aops->error_remove_page to ->error_remove_folio'
'Finish two folio conversions'
'More swap folio conversions'
- Kefeng Wang has also contributed folio-related work in the series
'mm: cleanup and use more folio in page fault'
- Jim Cromie has improved the kmemleak reporting output in the series
'tweak kmemleak report format'.
- In the series 'stackdepot: allow evicting stack traces' Andrey
Konovalov to permits clients (in this case KASAN) to cause eviction
of no longer needed stack traces.
- Charan Teja Kalla has fixed some accounting issues in the page
allocator's atomic reserve calculations in the series 'mm:
page_alloc: fixes for high atomic reserve caluculations'.
- Dmitry Rokosov has added to the samples/ dorectory some sample code
for a userspace memcg event listener application. See the series
'samples: introduce cgroup events listeners'.
- Some mapletree maintanance work from Liam Howlett in the series
'maple_tree: iterator state changes'.
- Nhat Pham has improved zswap's approach to writeback in the series
'workload-specific and memory pressure-driven zswap writeback'.
- DAMON/DAMOS feature and maintenance work from SeongJae Park in the
series
'mm/damon: let users feed and tame/auto-tune DAMOS'
'selftests/damon: add Python-written DAMON functionality tests'
'mm/damon: misc updates for 6.8'
- Yosry Ahmed has improved memcg's stats flushing in the series 'mm:
memcg: subtree stats flushing and thresholds'.
- In the series 'Multi-size THP for anonymous memory' Ryan Roberts
has added a runtime opt-in feature to transparent hugepages which
improves performance by allocating larger chunks of memory during
anonymous page faults.
- Matthew Wilcox has also contributed some cleanup and maintenance
work against eh buffer_head code int he series 'More buffer_head
cleanups'.
- Suren Baghdasaryan has done work on Andrea Arcangeli's series
'userfaultfd move option'. UFFDIO_MOVE permits userspace heap
compaction algorithms to move userspace's pages around rather than
UFFDIO_COPY'a alloc/copy/free.
- Stefan Roesch has developed a 'KSM Advisor', in the series 'mm/ksm:
Add ksm advisor'. This is a governor which tunes KSM's scanning
aggressiveness in response to userspace's current needs.
- Chengming Zhou has optimized zswap's temporary working memory use
in the series 'mm/zswap: dstmem reuse optimizations and cleanups'.
- Matthew Wilcox has performed some maintenance work on the writeback
code, both code and within filesystems. The series is 'Clean up the
writeback paths'.
- Andrey Konovalov has optimized KASAN's handling of alloc and free
stack traces for secondary-level allocators, in the series 'kasan:
save mempool stack traces'.
- Andrey also performed some KASAN maintenance work in the series
'kasan: assorted clean-ups'.
- David Hildenbrand has gone to town on the rmap code. Cleanups, more
pte batching, folio conversions and more. See the series 'mm/rmap:
interface overhaul'.
- Kinsey Ho has contributed some maintenance work on the MGLRU code
in the series 'mm/mglru: Kconfig cleanup'.
- Matthew Wilcox has contributed lruvec page accounting code cleanups
in the series 'Remove some lruvec page accounting functions'"
* tag 'mm-stable-2024-01-08-15-31' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (361 commits)
mm, treewide: rename MAX_ORDER to MAX_PAGE_ORDER
mm, treewide: introduce NR_PAGE_ORDERS
selftests/mm: add separate UFFDIO_MOVE test for PMD splitting
selftests/mm: skip test if application doesn't has root privileges
selftests/mm: conform test to TAP format output
selftests: mm: hugepage-mmap: conform to TAP format output
selftests/mm: gup_test: conform test to TAP format output
mm/selftests: hugepage-mremap: conform test to TAP format output
mm/vmstat: move pgdemote_* out of CONFIG_NUMA_BALANCING
mm: zsmalloc: return -ENOSPC rather than -EINVAL in zs_malloc while size is too large
mm/memcontrol: remove __mod_lruvec_page_state()
mm/khugepaged: use a folio more in collapse_file()
slub: use a folio in __kmalloc_large_node
slub: use folio APIs in free_large_kmalloc()
slub: use alloc_pages_node() in alloc_slab_page()
mm: remove inc/dec lruvec page state functions
mm: ratelimit stat flush from workingset shrinker
kasan: stop leaking stack trace handles
mm/mglru: remove CONFIG_TRANSPARENT_HUGEPAGE
mm/mglru: add dummy pmd_dirty()
...
commit 23baf831a3 ("mm, treewide: redefine MAX_ORDER sanely") has
changed the definition of MAX_ORDER to be inclusive. This has caused
issues with code that was not yet upstream and depended on the previous
definition.
To draw attention to the altered meaning of the define, rename MAX_ORDER
to MAX_PAGE_ORDER.
Link: https://lkml.kernel.org/r/20231228144704.14033-2-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCZZUzBQAKCRCRxhvAZXjc
ot+3AQCZw1PBD4azVxFMWH76qwlAGoVIFug4+ogKU/iUa4VLygEA2FJh1vLJw5iI
LpgBEIUTPVkwtzinAW94iJJo1Vr7NAI=
=p6PB
-----END PGP SIGNATURE-----
Merge tag 'vfs-6.8.iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs iov_iter cleanups from Christian Brauner:
"This contains a minor cleanup. The patches drop an unused argument
from import_single_range() allowing to replace import_single_range()
with import_ubuf() and dropping import_single_range() completely"
* tag 'vfs-6.8.iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
iov_iter: replace import_single_range() with import_ubuf()
iov_iter: remove unused 'iov' argument from import_single_range()
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCZZUzXQAKCRCRxhvAZXjc
ogOtAQDpqUp1zY4dV/dZisCJ5xarZTsSZ1AvgmcxZBtS0NhbdgEAshWvYGA9ryS/
ChL5jjtjjZDLhRA//reoFHTQIrdp2w8=
=bF+R
-----END PGP SIGNATURE-----
Merge tag 'vfs-6.8.rw' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs rw updates from Christian Brauner:
"This contains updates from Amir for read-write backing file helpers
for stacking filesystems such as overlayfs:
- Fanotify is currently in the process of introducing pre content
events. Roughly, a new permission event will be added indicating
that it is safe to write to the file being accessed. These events
are used by hierarchical storage managers to e.g., fill the content
of files on first access.
During that work we noticed that our current permission checking is
inconsistent in rw_verify_area() and remap_verify_area().
Especially in the splice code permission checking is done multiple
times. For example, one time for the whole range and then again for
partial ranges inside the iterator.
In addition, we mostly do permission checking before we call
file_start_write() except for a few places where we call it after.
For pre-content events we need such permission checking to be done
before file_start_write(). So this is a nice reason to clean this
all up.
After this series, all permission checking is done before
file_start_write().
As part of this cleanup we also massaged the splice code a bit. We
got rid of a few helpers because we are alredy drowning in special
read-write helpers. We also cleaned up the return types for splice
helpers.
- Introduce generic read-write helpers for backing files. This lifts
some overlayfs code to common code so it can be used by the FUSE
passthrough work coming in over the next cycles. Make Amir and
Miklos the maintainers for this new subsystem of the vfs"
* tag 'vfs-6.8.rw' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (30 commits)
fs: fix __sb_write_started() kerneldoc formatting
fs: factor out backing_file_mmap() helper
fs: factor out backing_file_splice_{read,write}() helpers
fs: factor out backing_file_{read,write}_iter() helpers
fs: prepare for stackable filesystems backing file helpers
fsnotify: optionally pass access range in file permission hooks
fsnotify: assert that file_start_write() is not held in permission hooks
fsnotify: split fsnotify_perm() into two hooks
fs: use splice_copy_file_range() inline helper
splice: return type ssize_t from all helpers
fs: use do_splice_direct() for nfsd/ksmbd server-side-copy
fs: move file_start_write() into direct_splice_actor()
fs: fork splice_file_range() from do_splice_direct()
fs: create {sb,file}_write_not_started() helpers
fs: create file_write_started() helper
fs: create __sb_write_started() helper
fs: move kiocb_start_write() into vfs_iocb_iter_write()
fs: move permission hook out of do_iter_read()
fs: move permission hook out of do_iter_write()
fs: move file_start_write() into vfs_iter_write()
...
The discard granularity now defaults to a single sector, so don't set
that value explicitly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20231228075545.362768-8-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The discard granularity now defaults to a single sector, so don't set
that value explicitly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20231228075545.362768-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The discard granularity now defaults to a single sector, so don't set
that value explicitly. Also don't bother clearing it as a discard
granularity without discard_sectors doesn't mean anything.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20231228075545.362768-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
BLK_DEF_MAX_SECTORS despite the confusing name is the default cap for
the max_sectors limits. Don't use it to initialize max_hw_setors, which
is a hardware / driver capacility.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20231227092305.279567-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
BLK_DEF_MAX_SECTORS despite the confusing name is the default cap for
the max_sectors limits. Don't use it to initialize max_hw_setors, which
is a hardware / driver capacility.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20231227092305.279567-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
null_blk has some rather odd capping of the max_hw_sectors value to
BLK_DEF_MAX_SECTORS, which doesn't make sense - max_hw_sector is the
hardware limit, and BLK_DEF_MAX_SECTORS despite the confusing name is the
default cap for the max_sectors field used for normal file system I/O.
Remove all the capping, and simply leave it to the block layer or
user to take up or not all of that for file system I/O.
Fixes: ea17fd354c ("null_blk: Allow controlling max_hw_sectors limit")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20231227092305.279567-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix all kernel-doc warnings in drbd_actlog.c:
drbd_actlog.c:963: warning: No description found for return value of 'drbd_rs_begin_io'
drbd_actlog.c:1015: warning: Function parameter or member 'peer_device' not described in 'drbd_try_rs_begin_io'
drbd_actlog.c:1015: warning: Excess function parameter 'device' description in 'drbd_try_rs_begin_io'
drbd_actlog.c:1015: warning: No description found for return value of 'drbd_try_rs_begin_io'
drbd_actlog.c:1197: warning: No description found for return value of 'drbd_rs_del_all'
Fix one spelling error (s/ore/or/).
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Cc: <drbd-dev@lists.linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <linux-block@vger.kernel.org>
Link: https://lore.kernel.org/r/20231222061909.8791-1-rdunlap@infradead.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Only use disk_set_zoned to actually enable zoned device support.
For clearing it, call disk_clear_zoned, which is renamed from
disk_clear_zone_settings and now directly clears the zoned flag as
well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20231217165359.604246-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When zones were first added the SCSI and ATA specs, two different
models were supported (in addition to the drive managed one that
is invisible to the host):
- host managed where non-conventional zones there is strict requirement
to write at the write pointer, or else an error is returned
- host aware where a write point is maintained if writes always happen
at it, otherwise it is left in an under-defined state and the
sequential write preferred zones behave like conventional zones
(probably very badly performing ones, though)
Not surprisingly this lukewarm model didn't prove to be very useful and
was finally removed from the ZBC and SBC specs (NVMe never implemented
it). Due to to the easily disappearing write pointer host software
could never rely on the write pointer to actually be useful for say
recovery.
Fortunately only a few HDD prototypes shipped using this model which
never made it to mass production. Drop the support before it is too
late. Note that any such host aware prototype HDD can still be used
with Linux as we'll now treat it as a conventional HDD.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20231217165359.604246-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
virtblk_revalidate_zones is called unconditionally from
virtblk_config_changed_work from the virtio config_changed callback.
virtblk_revalidate_zones is a bit odd in that it re-clears the zoned
state for host aware or non-zoned devices, which isn't needed unless the
zoned mode changed - but a zone mode change to a host managed model isn't
handled at all, and virtio_blk also doesn't handle any other config
change except for a capacity change is handled (and even if it was
the upper layers above virtio_blk wouldn't handle it very well).
But even the useful case of a size change that would add or remove
zones isn't handled properly as blk_revalidate_disk_zones expects the
device capacity to cover all zones, but the capacity is only updated
after virtblk_revalidate_zones.
As this code appears to be entirely untested and is getting in the way
remove it for now, but it can be readded in a fixed version with
proper test coverage if needed.
Fixes: 95bfec41bd ("virtio-blk: add support for zoned block devices")
Fixes: f1ba4e674f ("virtio-blk: fix to match virtio spec")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20231217165359.604246-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move reading and checking the zoned model from virtblk_probe_zoned_device
into the caller, leaving only the code to perform the actual setup for
host managed zoned devices in virtblk_probe_zoned_device.
This allows to share the model reading and sharing between builds with
and without CONFIG_BLK_DEV_ZONED, and improve it for the
!CONFIG_BLK_DEV_ZONED case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20231217165359.604246-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since "dev_search_path" can technically be as large as PATH_MAX,
there was a risk of truncation when copying it and a second string
into "full_path" since it was also PATH_MAX sized. The W=1 builds were
reporting this warning:
drivers/block/rnbd/rnbd-srv.c: In function 'process_msg_open.isra':
drivers/block/rnbd/rnbd-srv.c:616:51: warning: '%s' directive output may be truncated writing up to 254 bytes into a region of size between 0 and 4095 [-Wformat-truncation=]
616 | snprintf(full_path, PATH_MAX, "%s/%s",
| ^~
In function 'rnbd_srv_get_full_path',
inlined from 'process_msg_open.isra' at drivers/block/rnbd/rnbd-srv.c:721:14: drivers/block/rnbd/rnbd-srv.c:616:17: note: 'snprintf' output between 2 and 4351 bytes into a destination of size 4096
616 | snprintf(full_path, PATH_MAX, "%s/%s",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
617 | dev_search_path, dev_name);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~
To fix this, unconditionally check for truncation (as was already done
for the case where "%SESSNAME%" was present).
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312100355.lHoJPgKy-lkp@intel.com/
Cc: Md. Haris Iqbal <haris.iqbal@ionos.com>
Cc: Jack Wang <jinpu.wang@ionos.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <linux-block@vger.kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20231212214738.work.169-kees@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
linux/io_uring.h is slowly becoming a rubbish bin where we put
anything exposed to other subsystems. For instance, the task exit
hooks and io_uring cmd infra are completely orthogonal and don't need
each other's definitions. Start cleaning it up by splitting out all
command bits into a new header file.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/7ec50bae6e21f371d3850796e716917fc141225a.1701391955.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use kmap_local_page() instead of kmap_atomic() which has been
deprecated.
Link: https://lkml.kernel.org/r/20231128083845.848008-1-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
ZRAM_MEMORY_TRACKING enables two features:
- per-entry ac-time tracking
- debugfs interface
The latter one is the reason why memory-tracking depends on DEBUG_FS,
while the former one is used far beyond debugging these days. Namely
ac-time is used for fine grained writeback of idle entries (pages).
Move ac-time tracking under its own config option so that it can be
enabled (along with writeback) on systems without DEBUG_FS.
[senozhatsky@chromium.org: ifdef fixup, per Dmytro]
Link: https://lkml.kernel.org/r/20231117013543.540280-1-senozhatsky@chromium.org
Link: https://lkml.kernel.org/r/20231115024223.4133148-1-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Dmytro Maluka <dmaluka@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
With the removal of the 'iov' argument to import_single_range(), the two
functions are now fully identical. Convert the import_single_range()
callers to import_ubuf(), and remove the former fully.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/20231204174827.1258875-3-axboe@kernel.dk
Signed-off-by: Christian Brauner <brauner@kernel.org>
Commit 4e04005256 ("virtio-blk: support polling I/O") triggers the
following gcc 13 W=1 warnings:
drivers/block/virtio_blk.c: In function ‘init_vq’:
drivers/block/virtio_blk.c:1077:68: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 7 [-Wformat-truncation=]
1077 | snprintf(vblk->vqs[i].name, VQ_NAME_LEN, "req_poll.%d", i);
| ^~
drivers/block/virtio_blk.c:1077:58: note: directive argument in the range [-2147483648, 65534]
1077 | snprintf(vblk->vqs[i].name, VQ_NAME_LEN, "req_poll.%d", i);
| ^~~~~~~~~~~~~
drivers/block/virtio_blk.c:1077:17: note: ‘snprintf’ output between 11 and 21 bytes into a destination of size 16
1077 | snprintf(vblk->vqs[i].name, VQ_NAME_LEN, "req_poll.%d", i);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This is a false positive because the lower bound -2147483648 is
incorrect. The true range of i is [0, num_vqs - 1] where 0 < num_vqs <
65536.
The code mixes int, unsigned short, and unsigned int types in addition
to using "%d" for an unsigned value. Use unsigned short and "%u"
consistently to solve the compiler warning.
Cc: Suwan Kim <suwan.kim027@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312041509.DIyvEt9h-lkp@intel.com/
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20231204140743.1487843-1-stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
While printing error, replace %ld by %pe. %pe prints a string
whereas %ld would print an error code.
Signed-off-by: Supriti Singh <supriti.singh@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com>
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Link: https://lore.kernel.org/r/20231124213422.113449-3-haris.iqbal@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All the callers of vfs_iter_write() call file_start_write() just before
calling vfs_iter_write() except for target_core_file's fd_do_rw().
Move file_start_write() from the callers into vfs_iter_write().
fd_do_rw() calls vfs_iter_write() with a non-regular file, so
file_start_write() is a no-op.
This is needed for fanotify "pre content" events.
Suggested-by: Jan Kara <jack@suse.cz>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Link: https://lore.kernel.org/r/20231122122715.2561213-11-amir73il@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
If a socket is processing ioctl 'NBD_SET_SOCK', config->socks might be
krealloc in nbd_add_socket(), and a garbage request is received now, a UAF
may occurs.
T1
nbd_ioctl
__nbd_ioctl
nbd_add_socket
blk_mq_freeze_queue
T2
recv_work
nbd_read_reply
sock_xmit
krealloc config->socks
def config->socks
Pass nbd_sock to nbd_read_reply(). And introduce a new function
sock_xmit_recv(), which differs from sock_xmit only in the way it get
socket.
==================================================================
BUG: KASAN: use-after-free in sock_xmit+0x525/0x550
Read of size 8 at addr ffff8880188ec428 by task kworker/u12:1/18779
Workqueue: knbd4-recv recv_work
Call Trace:
__dump_stack
dump_stack+0xbe/0xfd
print_address_description.constprop.0+0x19/0x170
__kasan_report.cold+0x6c/0x84
kasan_report+0x3a/0x50
sock_xmit+0x525/0x550
nbd_read_reply+0xfe/0x2c0
recv_work+0x1c2/0x750
process_one_work+0x6b6/0xf10
worker_thread+0xdd/0xd80
kthread+0x30a/0x410
ret_from_fork+0x22/0x30
Allocated by task 18784:
kasan_save_stack+0x1b/0x40
kasan_set_track
set_alloc_info
__kasan_kmalloc
__kasan_kmalloc.constprop.0+0xf0/0x130
slab_post_alloc_hook
slab_alloc_node
slab_alloc
__kmalloc_track_caller+0x157/0x550
__do_krealloc
krealloc+0x37/0xb0
nbd_add_socket
+0x2d3/0x880
__nbd_ioctl
nbd_ioctl+0x584/0x8e0
__blkdev_driver_ioctl
blkdev_ioctl+0x2a0/0x6e0
block_ioctl+0xee/0x130
vfs_ioctl
__do_sys_ioctl
__se_sys_ioctl+0x138/0x190
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x61/0xc6
Freed by task 18784:
kasan_save_stack+0x1b/0x40
kasan_set_track+0x1c/0x30
kasan_set_free_info+0x20/0x40
__kasan_slab_free.part.0+0x13f/0x1b0
slab_free_hook
slab_free_freelist_hook
slab_free
kfree+0xcb/0x6c0
krealloc+0x56/0xb0
nbd_add_socket+0x2d3/0x880
__nbd_ioctl
nbd_ioctl+0x584/0x8e0
__blkdev_driver_ioctl
blkdev_ioctl+0x2a0/0x6e0
block_ioctl+0xee/0x130
vfs_ioctl
__do_sys_ioctl
__se_sys_ioctl+0x138/0x190
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x61/0xc6
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230911023308.3467802-1-linan666@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When CONFIG_BLK_DEV_NULL_BLK_FAULT_INJECTION is enabled, null_queue_rq()
would return BLK_STS_RESOURCE or BLK_STS_DEV_RESOURCE for the request,
which has been marked as MQ_RQ_IN_FLIGHT by blk_mq_start_request().
Then null_queue_rqs() put these requests in the rqlist, return back to
the block layer core, which would try to queue them individually again,
so the warning in blk_mq_start_request() triggered.
Fix it by splitting the null_queue_rq() into two parts: the first is the
preparation of request, the second is the handling of request. We put
the blk_mq_start_request() after the preparation part, which may fail
and return back to the block layer core.
The throttling also belongs to the preparation part, so move it before
blk_mq_start_request(). And change the return type of null_handle_cmd()
to void, since it always return BLK_STS_OK now.
Reported-by: <syzbot+fcc47ba2476570cbbeb0@syzkaller.appspotmail.com>
Closes: https://lore.kernel.org/all/0000000000000e6aac06098aee0c@google.com/
Fixes: d78bfa1346 ("block/null_blk: add queue_rqs() support")
Suggested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Link: https://lore.kernel.org/r/20231120032521.1012037-1-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Memory reordering may occur in nbd_genl_connect(), causing config_refs
to be set to 1 while nbd->config is still empty. Opening nbd at this
time will cause null-ptr-dereference.
T1 T2
nbd_open
nbd_get_config_unlocked
nbd_genl_connect
nbd_alloc_and_init_config
//memory reordered
refcount_set(&nbd->config_refs, 1) // 2
nbd->config
->null point
nbd->config = config // 1
Fix it by adding smp barrier to guarantee the execution sequence.
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20231116162316.1740402-4-linan666@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are no functional changes, just to make code cleaner and prepare
to fix null-ptr-dereference while accessing 'nbd->config'.
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20231116162316.1740402-3-linan666@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are no functional changes, make the code cleaner and prepare to
fix null-ptr-dereference while accessing 'nbd->config'.
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20231116162316.1740402-2-linan666@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 4af5f2e030 ("nbd: use blk_mq_alloc_disk and
blk_cleanup_disk") cleans up disk by blk_cleanup_disk() and it won't set
disk->private_data as NULL as before. UAF may be triggered in nbd_open()
if someone tries to open nbd device right after nbd_put() since nbd has
been free in nbd_dev_remove().
Fix this by implementing ->free_disk and free private data in it.
Fixes: 4af5f2e030 ("nbd: use blk_mq_alloc_disk and blk_cleanup_disk")
Signed-off-by: Li Lingfeng <lilingfeng3@huawei.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20231107103435.2074904-1-lilingfeng@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
vdpa/mlx5:
VHOST_BACKEND_F_ENABLE_AFTER_DRIVER_OK
new maintainer
vdpa:
support for vq descriptor mappings
decouple reset of iotlb mapping from device reset
fixes, cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmVCUMYPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp4L0H/RKcnNXPRqzhhBI1XVQ11Z8CO8WjovcmJalu
ADHNEGmvuWnY79fp9eLiZ4iVaTx1qbzqIB5Q500DJ65jh71W7UQ8ww6CGjNUoRGs
Zoe4G09WoOf4bvDZZzVV7ml/AzMdsHWSZK8pxY3QI9CsC9Zfp9hg20QYxPylCqYx
SIJx7w2MkoojfmtOHRx1WUxaQz99yfU4Z0C5PxtRE1HGN6/a1aY0P0CAl5jq8uCK
U5sCRsfCmP7VKlspeEddMiPA35ADbCiysSobCbwGVQEs5cHpMUX7KWa+oV0tF/PY
9uyJb2rJy6zG3tXmL4XNib665ZR86HX6qiWRfm2nBQQStuHaJyg=
=mXgo
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"vhost,virtio,vdpa: features, fixes, cleanups.
vdpa/mlx5:
- VHOST_BACKEND_F_ENABLE_AFTER_DRIVER_OK
- new maintainer
vdpa:
- support for vq descriptor mappings
- decouple reset of iotlb mapping from device reset
and fixes, cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (34 commits)
vdpa_sim: implement .reset_map support
vdpa/mlx5: implement .reset_map driver op
vhost-vdpa: clean iotlb map during reset for older userspace
vdpa: introduce .compat_reset operation callback
vhost-vdpa: introduce IOTLB_PERSIST backend feature bit
vhost-vdpa: reset vendor specific mapping to initial state in .release
vdpa: introduce .reset_map operation callback
virtio_pci: add check for common cfg size
virtio-blk: fix implicit overflow on virtio_max_dma_size
virtio_pci: add build offset check for the new common cfg items
virtio: add definition of VIRTIO_F_NOTIF_CONFIG_DATA feature bit
vduse: make vduse_class constant
vhost-scsi: Spelling s/preceeding/preceding/g
virtio: kdoc for struct virtio_pci_modern_device
vdpa: Update sysfs ABI documentation
MAINTAINERS: Add myself as mlx5_vdpa driver
virtio-balloon: correct the comment of virtballoon_migratepage()
mlx5_vdpa: offer VHOST_BACKEND_F_ENABLE_AFTER_DRIVER_OK
vdpa/mlx5: Update cvq iotlb mapping on ASID change
vdpa/mlx5: Make iotlb helper functions more generic
...
-----BEGIN PGP SIGNATURE-----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=sace
-----END PGP SIGNATURE-----
Merge tag 'for-6.7/block-2023-10-30' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- Improvements to the queue_rqs() support, and adding null_blk support
for that as well (Chengming)
- Series improving badblocks support (Coly)
- Key store support for sed-opal (Greg)
- IBM partition string handling improvements (Jan)
- Make number of ublk devices supported configurable (Mike)
- Cancelation improvements for ublk (Ming)
- MD pull requests via Song:
- Handle timeout in md-cluster, by Denis Plotnikov
- Cleanup pers->prepare_suspend, by Yu Kuai
- Rewrite mddev_suspend(), by Yu Kuai
- Simplify md_seq_ops, by Yu Kuai
- Reduce unnecessary locking array_state_store(), by Mariusz
Tkaczyk
- Make rdev add/remove independent from daemon thread, by Yu Kuai
- Refactor code around quiesce() and mddev_suspend(), by Yu Kuai
- NVMe pull request via Keith:
- nvme-auth updates (Mark)
- nvme-tcp tls (Hannes)
- nvme-fc annotaions (Kees)
- Misc cleanups and improvements (Jiapeng, Joel)
* tag 'for-6.7/block-2023-10-30' of git://git.kernel.dk/linux: (95 commits)
block: ublk_drv: Remove unused function
md: cleanup pers->prepare_suspend()
nvme-auth: allow mixing of secret and hash lengths
nvme-auth: use transformed key size to create resp
nvme-auth: alloc nvme_dhchap_key as single buffer
nvmet-tcp: use 'spin_lock_bh' for state_lock()
powerpc/pseries: PLPKS SED Opal keystore support
block: sed-opal: keystore access for SED Opal keys
block:sed-opal: SED Opal keystore
ublk: simplify aborting request
ublk: replace monitor with cancelable uring_cmd
ublk: quiesce request queue when aborting queue
ublk: rename mm_lock as lock
ublk: move ublk_cancel_dev() out of ub->mutex
ublk: make sure io cmd handled in submitter task context
ublk: don't get ublk device reference in ublk_abort_queue()
ublk: Make ublks_max configurable
ublk: Limit dev_id/ub_number values
md-cluster: check for timeout while a new disk adding
nvme: rework NVME_AUTH Kconfig selection
...
The following codes have an implicit conversion from size_t to u32:
(u32)max_size = (size_t)virtio_max_dma_size(vdev);
This may lead overflow, Ex (size_t)4G -> (u32)0. Once
virtio_max_dma_size() has a larger size than U32_MAX, use U32_MAX
instead.
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20230904061045.510460-1-pizhenwei@bytedance.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
- Add LKDTM test for stuck CPUs (Mark Rutland)
- Improve LKDTM selftest behavior under UBSan (Ricardo Cañuelo)
- Refactor more 1-element arrays into flexible arrays (Gustavo A. R. Silva)
- Analyze and replace strlcpy and strncpy uses (Justin Stitt, Azeem Shaikh)
- Convert group_info.usage to refcount_t (Elena Reshetova)
- Add __counted_by annotations (Kees Cook, Gustavo A. R. Silva)
- Add Kconfig fragment for basic hardening options (Kees Cook, Lukas Bulwahn)
- Fix randstruct GCC plugin performance mode to stay in groups (Kees Cook)
- Fix strtomem() compile-time check for small sources (Kees Cook)
-----BEGIN PGP SIGNATURE-----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=0iVF
-----END PGP SIGNATURE-----
Merge tag 'hardening-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"One of the more voluminous set of changes is for adding the new
__counted_by annotation[1] to gain run-time bounds checking of
dynamically sized arrays with UBSan.
- Add LKDTM test for stuck CPUs (Mark Rutland)
- Improve LKDTM selftest behavior under UBSan (Ricardo Cañuelo)
- Refactor more 1-element arrays into flexible arrays (Gustavo A. R.
Silva)
- Analyze and replace strlcpy and strncpy uses (Justin Stitt, Azeem
Shaikh)
- Convert group_info.usage to refcount_t (Elena Reshetova)
- Add __counted_by annotations (Kees Cook, Gustavo A. R. Silva)
- Add Kconfig fragment for basic hardening options (Kees Cook, Lukas
Bulwahn)
- Fix randstruct GCC plugin performance mode to stay in groups (Kees
Cook)
- Fix strtomem() compile-time check for small sources (Kees Cook)"
* tag 'hardening-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (56 commits)
hwmon: (acpi_power_meter) replace open-coded kmemdup_nul
reset: Annotate struct reset_control_array with __counted_by
kexec: Annotate struct crash_mem with __counted_by
virtio_console: Annotate struct port_buffer with __counted_by
ima: Add __counted_by for struct modsig and use struct_size()
MAINTAINERS: Include stackleak paths in hardening entry
string: Adjust strtomem() logic to allow for smaller sources
hardening: x86: drop reference to removed config AMD_IOMMU_V2
randstruct: Fix gcc-plugin performance mode to stay in group
mailbox: zynqmp: Annotate struct zynqmp_ipi_pdata with __counted_by
drivers: thermal: tsens: Annotate struct tsens_priv with __counted_by
irqchip/imx-intmux: Annotate struct intmux_data with __counted_by
KVM: Annotate struct kvm_irq_routing_table with __counted_by
virt: acrn: Annotate struct vm_memory_region_batch with __counted_by
hwmon: Annotate struct gsc_hwmon_platform_data with __counted_by
sparc: Annotate struct cpuinfo_tree with __counted_by
isdn: kcapi: replace deprecated strncpy with strscpy_pad
isdn: replace deprecated strncpy with strscpy
NFS/flexfiles: Annotate struct nfs4_ff_layout_segment with __counted_by
nfs41: Annotate struct nfs4_file_layout_dsaddr with __counted_by
...
disk_check_media_change is mostly called from ->open where it makes
little sense to mark the file system on the device as dead, as we
are just opening it. So instead of calling bdev_mark_dead from
disk_check_media_change move it into the few callers that are not
in an open instance. This avoid calling into bdev_mark_dead and
thus taking s_umount with open_mutex held.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20231017184823.1383356-4-hch@lst.de
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Convert zram to use bdev_open_by_dev() and pass the handle around.
CC: Minchan Kim <minchan@kernel.org>
CC: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230927093442.25915-8-jack@suse.cz
Signed-off-by: Christian Brauner <brauner@kernel.org>
Convert rnbd-srv to use bdev_open_by_path() and pass the handle
around.
CC: Jack Wang <jinpu.wang@ionos.com>
CC: "Md. Haris Iqbal" <haris.iqbal@ionos.com>
Acked-by: "Md. Haris Iqbal" <haris.iqbal@ionos.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230927093442.25915-6-jack@suse.cz
Signed-off-by: Christian Brauner <brauner@kernel.org>
Convert pktcdvd to use bdev_open_by_dev().
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230927093442.25915-5-jack@suse.cz
Signed-off-by: Christian Brauner <brauner@kernel.org>
The function are defined in the ublk_drv.c file, but not called
elsewhere, so delete the unused function.
drivers/block/ublk_drv.c:1211:20: warning: unused function 'ublk_abort_io_cmds'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=6938
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Fixes: b4e1353f46 ("ublk: simplify aborting request")
Reviewed-by: Ming Lei <ming.lei@rehdat.com>
Link: https://lore.kernel.org/r/20231019030444.53680-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now ublk_abort_queue() is run exclusively with ublk_queue_rq() and the
ubq_daemon task, so simplify aborting request:
- set UBLK_IO_FLAG_ABORTED in ublk_abort_queue() just for aborting
this request
- abort request in ublk_queue_rq() if ubq->canceling is set
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20231009093324.957829-8-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Monitor work actually introduces one extra context for handling abort, this
way is easy to cause race, and also introduce extra delay when handling
aborting.
Now we start to support cancelable uring_cmd, so use it instead:
1) this cancel callback is either run from the uring cmd submission task
context or called after the io_uring context is exit, so the callback is
run exclusively with ublk_ch_uring_cmd() and __ublk_rq_task_work().
2) the previous patch freezes request queue when calling ublk_abort_queue(),
which is now completely exclusive with ublk_queue_rq() and
ublk_ch_uring_cmd()/__ublk_rq_task_work().
3) in timeout handler, if all IOs are in-flight, then all uring commands
are completed, uring command canceling can't help us to provide forward
progress any more, so call ublk_abort_requests() in timeout handler.
This way simplifies aborting queue, and is helpful for adding new feature,
such as, relax the limit of using single task for handling one queue.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20231009093324.957829-7-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
So far aborting queue ends request when the ubq daemon is exiting, and
it can be run concurrently with ublk_queue_rq(), this way is fragile and
we depend on the tricky usage of UBLK_IO_FLAG_ABORTED for avoiding such
race.
Quiesce queue when aborting queue, and the two code paths can be run
completely exclusively, then it becomes easier to add new ublk feature,
such as relaxing single same task limit for each queue.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20231009093324.957829-6-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rename mm_lock field of ublk_device as lock, so that this lock can be reused
for protecting access of ub->ub_disk, which will be used for simplifying
ublk_abort_queue() by quiesce queue in next patch.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20231009093324.957829-5-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ublk_cancel_dev() just calls ublk_cancel_queue() to cancel all pending
io commands after ublk request queue is idle. The only protection is just
the read & write of ubq->nr_io_ready and avoid duplicated command cancel,
so add one per-queue lock with cancel flag for providing this protection,
meantime move ublk_cancel_dev() out of ub->mutex.
Then we needn't to call io_uring_cmd_complete_in_task() to cancel
pending command. And the same cancel logic will be re-used for
cancelable uring command.
This patch basically reverts commit ac5902f84b ("ublk: fix AB-BA lockdep warning").
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20231009093324.957829-4-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In well-done ublk server implementation, ublk io command won't be
linked into any link chain. Meantime they are always handled in no-wait
style, so basically io cmd is always handled in submitter task context.
However, the server may set IOSQE_ASYNC, or io command is linked to one
chain mistakenly, then we may still run into io-wq context and
ctx->uring_lock isn't held.
So in case of IO_URING_F_UNLOCKED, schedule this command by
io_uring_cmd_complete_in_task to force running it in submitter task. Then
ublk_ch_uring_cmd_local() is guaranteed to run with context uring_lock held,
and we needn't to worry about sync among submission code path any more.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20231009093324.957829-3-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
ublk_abort_queue() is called in ublk_daemon_monitor_work(), in which
it is guaranteed that the device is live because monitor work is
canceled when removing device, so no need to get the device reference.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20231009093324.957829-2-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We are converting tcmu applications to ublk, but have systems with up
to 1k devices. This patch allows us to configure the ublks_max from
userspace with the ublks_max modparam.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20231012150600.6198-3-michael.christie@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The dev_id/ub_number is used for the ublk dev's char device's minor
number so it has to fit into MINORMASK. This patch adds checks to prevent
userspace from passing a number that's too large and limits what can be
allocated by the ublk_index_idr for the case where userspace has the
kernel allocate the dev_id/ub_number.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20231012150600.6198-2-michael.christie@oracle.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=NWf+
-----END PGP SIGNATURE-----
Merge tag 'block-6.6-2023-10-06' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
"Just two minor fixes, for nbd and md"
* tag 'block-6.6-2023-10-06' of git://git.kernel.dk/linux:
nbd: don't call blk_mark_disk_dead nbd_clear_sock_ioctl
md/raid5: release batch_last before waiting for another stripe_head
blk_mark_disk_dead is the proper interface to shut down a block
device, but it also makes the disk unusable forever.
nbd_clear_sock_ioctl on the other hand wants to shut down the file
system, but allow the block device to be used again when when connected
to another socket. Switch nbd to use disk_force_media_change and
nbd_bdev_reset to go back to a behavior of the old __invalidate_device
call, with the added benefit of incrementing the device generation
as there is no guarantee the old content comes back when the device
is reconnected.
Reported-by: Samuel Holland <samuel.holland@sifive.com>
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Fixes: 0c1c9a27ce ("nbd: call blk_mark_disk_dead in nbd_clear_sock_ioctl")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20231003153106.1331363-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
`strncpy` is deprecated for use on NUL-terminated destination strings [1].
We should favor a more robust and less ambiguous interface.
We expect that both `nullb->disk_name` and `disk->disk_name` be
NUL-terminated:
| snprintf(nullb->disk_name, sizeof(nullb->disk_name),
| "%s", config_item_name(&dev->group.cg_item));
...
| pr_info("disk %s created\n", nullb->disk_name);
It seems like NUL-padding may be required due to __assign_disk_name()
utilizing a memcpy as opposed to a `str*cpy` api.
| static inline void __assign_disk_name(char *name, struct gendisk *disk)
| {
| if (disk)
| memcpy(name, disk->disk_name, DISK_NAME_LEN);
| else
| memset(name, 0, DISK_NAME_LEN);
| }
Then we go and print it with `__print_disk_name` which wraps `nullb_trace_disk_name()`.
| #define __print_disk_name(name) nullb_trace_disk_name(p, name)
This function obviously expects a NUL-terminated string.
| const char *nullb_trace_disk_name(struct trace_seq *p, char *name)
| {
| const char *ret = trace_seq_buffer_ptr(p);
|
| if (name && *name)
| trace_seq_printf(p, "disk=%s, ", name);
| trace_seq_putc(p, 0);
|
| return ret;
| }
>From the above, we need both 1) a NUL-terminated string and 2) a
NUL-padded string. So, let's use strscpy_pad() as per Kees' suggestion
from v1.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Cc: Kees Cook <keescook@chromium.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230919-strncpy-drivers-block-null_blk-main-c-v3-1-10cf0a87a2c3@google.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct fifo_buffer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: drbd-dev@lists.linbit.com
Cc: linux-block@vger.kernel.org
Reviewed-by: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230915200316.never.707-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
rbd_dev_refresh() has been holding header_rwsem across header and
parent info read-in unnecessarily for ages. With commit 870611e487
("rbd: get snapshot context after exclusive lock is ensured to be
held"), the potential for deadlocks became much more real owning to
a) header_rwsem now nesting inside lock_rwsem and b) rw_semaphores
not allowing new readers after a writer is registered.
For example, assuming that I/O request 1, I/O request 2 and header
read-in request all target the same OSD:
1. I/O request 1 comes in and gets submitted
2. watch error occurs
3. rbd_watch_errcb() takes lock_rwsem for write, clears owner_cid and
releases lock_rwsem
4. after reestablishing the watch, rbd_reregister_watch() calls
rbd_dev_refresh() which takes header_rwsem for write and submits
a header read-in request
5. I/O request 2 comes in: after taking lock_rwsem for read in
__rbd_img_handle_request(), it blocks trying to take header_rwsem
for read in rbd_img_object_requests()
6. another watch error occurs
7. rbd_watch_errcb() blocks trying to take lock_rwsem for write
8. I/O request 1 completion is received by the messenger but can't be
processed because lock_rwsem won't be granted anymore
9. header read-in request completion can't be received, let alone
processed, because the messenger is stranded
Change rbd_dev_refresh() to take header_rwsem only for actually
updating rbd_dev->header. Header and parent info read-in don't need
any locking.
Cc: stable@vger.kernel.org # 0b035401c570: rbd: move rbd_dev_refresh() definition
Cc: stable@vger.kernel.org # 510a7330c82a: rbd: decouple header read-in from updating rbd_dev->header
Cc: stable@vger.kernel.org # c10311776f0a: rbd: decouple parent info read-in from updating rbd_dev
Cc: stable@vger.kernel.org
Fixes: 870611e487 ("rbd: get snapshot context after exclusive lock is ensured to be held")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
Unlike header read-in, parent info read-in is already decoupled in
get_parent_info(), but it's buried in rbd_dev_v2_parent_info() along
with the processing logic.
Separate the initial read-in and update read-in logic into
rbd_dev_setup_parent() and rbd_dev_update_parent() respectively and
have rbd_dev_v2_parent_info() just populate struct parent_image_info
(i.e. what get_parent_info() did). Some existing QoI issues, like
flatten of a standalone clone being disregarded on refresh, remain.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
Make rbd_dev_header_info() populate a passed struct rbd_image_header
instead of rbd_dev->header and introduce rbd_dev_update_header() for
updating mutable fields in rbd_dev->header upon refresh. The initial
read-in of both mutable and immutable fields in rbd_dev_image_probe()
passes in rbd_dev->header so no update step is required there.
rbd_init_layout() is now called directly from rbd_dev_image_probe()
instead of individually in format 1 and format 2 implementations.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
Move rbd_dev_refresh() definition further down to avoid having to
move struct parent_image_info definition in the next commit. This
spares some forward declarations too.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
Add batched mq_ops.queue_rqs() support in null_blk for testing. The
implementation is much easy since null_blk doesn't have commit_rqs().
We simply handle each request one by one, if errors are encountered,
leave them in the passed in list and return back.
There is about 3.6% improvement in IOPS of fio/t/io_uring on null_blk
with hw_queue_depth=256 on my test VM, from 1.09M to 1.13M.
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230913151616.3164338-6-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now we update driver tags request table in blk_mq_get_driver_tag(),
so the driver that support queue_rqs() have to update that inflight
table by itself.
Move it to blk_mq_start_request(), which is a better place where
we setup the deadline for request timeout check. And it's just
where the request becomes inflight.
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230913151616.3164338-5-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=4SLW
-----END PGP SIGNATURE-----
Merge tag 'block-6.6-2023-09-08' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- Fix null_blk polled IO timeout handling (Chengming)
- Regression fix for swapped arguments in drbd bvec_set_page()
(Christoph)
- String length handling fix for s390 dasd (Heiko)
- Fixes for blk-throttle accounting (Yu)
- Fix page pinning issue for same page segments (Christoph)
- Remove redundant file_remove_privs() call (Christoph)
- Fix a regression in partition handling for devices not supporting
partitions (Li)
* tag 'block-6.6-2023-09-08' of git://git.kernel.dk/linux:
drbd: swap bvec_set_page len and offset
block: fix pin count management when merging same-page segments
null_blk: fix poll request timeout handling
s390/dasd: fix string length handling
block: don't add or resize partition on the disk with GENHD_FL_NO_PART
block: remove the call to file_remove_privs in blkdev_write_iter
blk-throttle: consider 'carryover_ios/bytes' in throtl_trim_slice()
blk-throttle: use calculate_io/bytes_allowed() for throtl_trim_slice()
blk-throttle: fix wrong comparation while 'carryover_ios/bytes' is negative
blk-throttle: print signed value 'carryover_bytes/ios' for user
fscrypt support to CephFS! The list of things which don't work with
encryption should be fairly short, mostly around the edges: fallocate
(not supported well in CephFS to begin with), copy_file_range (requires
re-encryption), non-default striping patterns.
This was a multi-year effort principally by Jeff Layton with assistance
from Xiubo Li, Luís Henriques and others, including several dependant
changes in the MDS, netfs helper library and fscrypt framework itself.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmT4pl4THGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi5kzB/4sMgzZyUa3T1vA/G2pPvEkyy1qDxsW
y+o4dDMWA9twcrBVpNuGd54wbXpmO/LAekHEdorjayH+f0zf10MsnP1ePz9WB3NG
jr7RRujb+Gpd2OFYJXGSEbd3faTg8M2kpGCCrVe7SFNoyu8z9NwFItwWMog5aBjX
ODGQrq+kA4ARA6xIqwzF5gP0zr+baT9rWhQdm7Xo9itWdosnbyDLJx1dpEfLuqBX
te3SmifDzedn3Gw73hdNo/+ybw0kHARoK+RmXCTsoDDQw+JsoO9KxZF5Q8QcDELq
2woPNp0Hl+Dm4MkzGnPxv56Qj8ZDViS59syXC0CfGRmu4nzF1Rw+0qn5
=/WlE
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-6.6-rc1' of https://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"Mixed with some fixes and cleanups, this brings in reasonably complete
fscrypt support to CephFS! The list of things which don't work with
encryption should be fairly short, mostly around the edges: fallocate
(not supported well in CephFS to begin with), copy_file_range
(requires re-encryption), non-default striping patterns.
This was a multi-year effort principally by Jeff Layton with
assistance from Xiubo Li, Luís Henriques and others, including several
dependant changes in the MDS, netfs helper library and fscrypt
framework itself"
* tag 'ceph-for-6.6-rc1' of https://github.com/ceph/ceph-client: (53 commits)
ceph: make num_fwd and num_retry to __u32
ceph: make members in struct ceph_mds_request_args_ext a union
rbd: use list_for_each_entry() helper
libceph: do not include crypto/algapi.h
ceph: switch ceph_lookup/atomic_open() to use new fscrypt helper
ceph: fix updating i_truncate_pagecache_size for fscrypt
ceph: wait for OSD requests' callbacks to finish when unmounting
ceph: drop messages from MDS when unmounting
ceph: update documentation regarding snapshot naming limitations
ceph: prevent snapshot creation in encrypted locked directories
ceph: add support for encrypted snapshot names
ceph: invalidate pages when doing direct/sync writes
ceph: plumb in decryption during reads
ceph: add encryption support to writepage and writepages
ceph: add read/modify/write to ceph_sync_write
ceph: align data in pages in ceph_sync_write
ceph: don't use special DIO path for encrypted inodes
ceph: add truncate size handling support for fscrypt
ceph: add object version support for sync read
libceph: allow ceph_osdc_new_request to accept a multi-op read
...
bvec_set_page has the following signature:
static inline void bvec_set_page(struct bio_vec *bv, struct page *page,
unsigned int len, unsigned int offset)
However, the usage in DRBD swaps the len and offset parameters. This
leads to a bvec with length=0 instead of the intended length=4096, which
causes sock_sendmsg to return -EIO.
This leaves DRBD unable to transmit any pages and thus completely
broken.
Swapping the parameters fixes the regression.
Fixes: eeac7405c7 ("drbd: Use sendmsg(MSG_SPLICE_PAGES) rather than sendpage()")
Reported-by: Serguei Ivantsov <manowar@gsc-game.com>
Link: https://lore.kernel.org/regressions/CAKH+VT3YLmAn0Y8=q37UTDShqxDLsqPcQ4hBMzY7HPn7zNx+RQ@mail.gmail.com/
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20230906133034.948817-1-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When doing io_uring benchmark on /dev/nullb0, it's easy to crash the
kernel if poll requests timeout triggered, as reported by David. [1]
BUG: kernel NULL pointer dereference, address: 0000000000000008
Workqueue: kblockd blk_mq_timeout_work
RIP: 0010:null_timeout_rq+0x4e/0x91
Call Trace:
? null_timeout_rq+0x4e/0x91
blk_mq_handle_expired+0x31/0x4b
bt_iter+0x68/0x84
? bt_tags_iter+0x81/0x81
__sbitmap_for_each_set.constprop.0+0xb0/0xf2
? __blk_mq_complete_request_remote+0xf/0xf
bt_for_each+0x46/0x64
? __blk_mq_complete_request_remote+0xf/0xf
? percpu_ref_get_many+0xc/0x2a
blk_mq_queue_tag_busy_iter+0x14d/0x18e
blk_mq_timeout_work+0x95/0x127
process_one_work+0x185/0x263
worker_thread+0x1b5/0x227
This is indeed a race problem between null_timeout_rq() and null_poll().
null_poll() null_timeout_rq()
spin_lock(&nq->poll_lock)
list_splice_init(&nq->poll_list, &list)
spin_unlock(&nq->poll_lock)
while (!list_empty(&list))
req = list_first_entry()
list_del_init()
...
blk_mq_add_to_batch()
// req->rq_next = NULL
spin_lock(&nq->poll_lock)
// rq->queuelist->next == NULL
list_del_init(&rq->queuelist)
spin_unlock(&nq->poll_lock)
Fix these problems by setting requests state to MQ_RQ_COMPLETE under
nq->poll_lock protection, in which null_timeout_rq() can safely detect
this race and early return.
Note this patch just fix the kernel panic when request timeout happen.
[1] https://lore.kernel.org/all/3893581.1691785261@warthog.procyon.org.uk/
Fixes: 0a593fbbc2 ("null_blk: poll queue support")
Reported-by: David Howells <dhowells@redhat.com>
Tested-by: David Howells <dhowells@redhat.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Link: https://lore.kernel.org/r/20230901120306.170520-2-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Convert list_for_each() to list_for_each_entry() so that the tmp
list_head pointer and list_entry() call are no longer needed, which
can reduce a few lines of code. No functional changed.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
-----BEGIN PGP SIGNATURE-----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=p1bd
-----END PGP SIGNATURE-----
Merge tag 'for-6.6/block-2023-08-28' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
"Pretty quiet round for this release. This contains:
- Add support for zoned storage to ublk (Andreas, Ming)
- Series improving performance for drivers that mark themselves as
needing a blocking context for issue (Bart)
- Cleanup the flush logic (Chengming)
- sed opal keyring support (Greg)
- Fixes and improvements to the integrity support (Jinyoung)
- Add some exports for bcachefs that we can hopefully delete again in
the future (Kent)
- deadline throttling fix (Zhiguo)
- Series allowing building the kernel without buffer_head support
(Christoph)
- Sanitize the bio page adding flow (Christoph)
- Write back cache fixes (Christoph)
- MD updates via Song:
- Fix perf regression for raid0 large sequential writes (Jan)
- Fix split bio iostat for raid0 (David)
- Various raid1 fixes (Heinz, Xueshi)
- raid6test build fixes (WANG)
- Deprecate bitmap file support (Christoph)
- Fix deadlock with md sync thread (Yu)
- Refactor md io accounting (Yu)
- Various non-urgent fixes (Li, Yu, Jack)
- Various fixes and cleanups (Arnd, Azeem, Chengming, Damien, Li,
Ming, Nitesh, Ruan, Tejun, Thomas, Xu)"
* tag 'for-6.6/block-2023-08-28' of git://git.kernel.dk/linux: (113 commits)
block: use strscpy() to instead of strncpy()
block: sed-opal: keyring support for SED keys
block: sed-opal: Implement IOC_OPAL_REVERT_LSP
block: sed-opal: Implement IOC_OPAL_DISCOVERY
blk-mq: prealloc tags when increase tagset nr_hw_queues
blk-mq: delete redundant tagset map update when fallback
blk-mq: fix tags leak when shrink nr_hw_queues
ublk: zoned: support REQ_OP_ZONE_RESET_ALL
md: raid0: account for split bio in iostat accounting
md/raid0: Fix performance regression for large sequential writes
md/raid0: Factor out helper for mapping and submitting a bio
md raid1: allow writebehind to work on any leg device set WriteMostly
md/raid1: hold the barrier until handle_read_error() finishes
md/raid1: free the r1bio before waiting for blocked rdev
md/raid1: call free_r1bio() before allow_barrier() in raid_end_bio_io()
blk-cgroup: Fix NULL deref caused by blkg_policy_data being installed before init
drivers/rnbd: restore sysfs interface to rnbd-client
md/raid5-cache: fix null-ptr-deref for r5l_flush_stripe_to_raid()
raid6: test: only check for Altivec if building on powerpc hosts
raid6: test: make sure all intermediate and artifact files are .gitignored
...
Core
----
- Increase size limits for to-be-sent skb frag allocations. This
allows tun, tap devices and packet sockets to better cope with large
writes operations.
- Store netdevs in an xarray, to simplify iterating over netdevs.
- Refactor nexthop selection for multipath routes.
- Improve sched class lifetime handling.
- Add backup nexthop ID support for bridge.
- Implement drop reasons support in openvswitch.
- Several data races annotations and fixes.
- Constify the sk parameter of routing functions.
- Prepend kernel version to netconsole message.
Protocols
---------
- Implement support for TCP probing the peer being under memory
pressure.
- Remove hard coded limitation on IPv6 specific info placement
inside the socket struct.
- Get rid of sysctl_tcp_adv_win_scale and use an auto-estimated
per socket scaling factor.
- Scaling-up the IPv6 expired route GC via a separated list of
expiring routes.
- In-kernel support for the TLS alert protocol.
- Better support for UDP reuseport with connected sockets.
- Add NEXT-C-SID support for SRv6 End.X behavior, reducing the SR
header size.
- Get rid of additional ancillary per MPTCP connection struct socket.
- Implement support for BPF-based MPTCP packet schedulers.
- Format MPTCP subtests selftests results in TAP.
- Several new SMC 2.1 features including unique experimental options,
max connections per lgr negotiation, max links per lgr negotiation.
BPF
---
- Multi-buffer support in AF_XDP.
- Add multi uprobe BPF links for attaching multiple uprobes
and usdt probes, which is significantly faster and saves extra fds.
- Implement an fd-based tc BPF attach API (TCX) and BPF link support on
top of it.
- Add SO_REUSEPORT support for TC bpf_sk_assign.
- Support new instructions from cpu v4 to simplify the generated code and
feature completeness, for x86, arm64, riscv64.
- Support defragmenting IPv(4|6) packets in BPF.
- Teach verifier actual bounds of bpf_get_smp_processor_id()
and fix perf+libbpf issue related to custom section handling.
- Introduce bpf map element count and enable it for all program types.
- Add a BPF hook in sys_socket() to change the protocol ID
from IPPROTO_TCP to IPPROTO_MPTCP to cover migration for legacy.
- Introduce bpf_me_mcache_free_rcu() and fix OOM under stress.
- Add uprobe support for the bpf_get_func_ip helper.
- Check skb ownership against full socket.
- Support for up to 12 arguments in BPF trampoline.
- Extend link_info for kprobe_multi and perf_event links.
Netfilter
---------
- Speed-up process exit by aborting ruleset validation if a
fatal signal is pending.
- Allow NLA_POLICY_MASK to be used with BE16/BE32 types.
Driver API
----------
- Page pool optimizations, to improve data locality and cache usage.
- Introduce ndo_hwtstamp_get() and ndo_hwtstamp_set() to avoid the need
for raw ioctl() handling in drivers.
- Simplify genetlink dump operations (doit/dumpit) providing them
the common information already populated in struct genl_info.
- Extend and use the yaml devlink specs to [re]generate the split ops.
- Introduce devlink selective dumps, to allow SF filtering SF based on
handle and other attributes.
- Add yaml netlink spec for netlink-raw families, allow route, link and
address related queries via the ynl tool.
- Remove phylink legacy mode support.
- Support offload LED blinking to phy.
- Add devlink port function attributes for IPsec.
New hardware / drivers
----------------------
- Ethernet:
- Broadcom ASP 2.0 (72165) ethernet controller
- MediaTek MT7988 SoC
- Texas Instruments AM654 SoC
- Texas Instruments IEP driver
- Atheros qca8081 phy
- Marvell 88Q2110 phy
- NXP TJA1120 phy
- WiFi:
- MediaTek mt7981 support
- Can:
- Kvaser SmartFusion2 PCI Express devices
- Allwinner T113 controllers
- Texas Instruments tcan4552/4553 chips
- Bluetooth:
- Intel Gale Peak
- Qualcomm WCN3988 and WCN7850
- NXP AW693 and IW624
- Mediatek MT2925
Drivers
-------
- Ethernet NICs:
- nVidia/Mellanox:
- mlx5:
- support UDP encapsulation in packet offload mode
- IPsec packet offload support in eswitch mode
- improve aRFS observability by adding new set of counters
- extends MACsec offload support to cover RoCE traffic
- dynamic completion EQs
- mlx4:
- convert to use auxiliary bus instead of custom interface logic
- Intel
- ice:
- implement switchdev bridge offload, even for LAG interfaces
- implement SRIOV support for LAG interfaces
- igc:
- add support for multiple in-flight TX timestamps
- Broadcom:
- bnxt:
- use the unified RX page pool buffers for XDP and non-XDP
- use the NAPI skb allocation cache
- OcteonTX2:
- support Round Robin scheduling HTB offload
- TC flower offload support for SPI field
- Freescale:
- add XDP_TX feature support
- AMD:
- ionic: add support for PCI FLR event
- sfc:
- basic conntrack offload
- introduce eth, ipv4 and ipv6 pedit offloads
- ST Microelectronics:
- stmmac: maximze PTP timestamping resolution
- Virtual NICs:
- Microsoft vNIC:
- batch ringing RX queue doorbell on receiving packets
- add page pool for RX buffers
- Virtio vNIC:
- add per queue interrupt coalescing support
- Google vNIC:
- add queue-page-list mode support
- Ethernet high-speed switches:
- nVidia/Mellanox (mlxsw):
- add port range matching tc-flower offload
- permit enslavement to netdevices with uppers
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- convert to phylink_pcs
- Renesas:
- r8A779fx: add speed change support
- rzn1: enables vlan support
- Ethernet PHYs:
- convert mv88e6xxx to phylink_pcs
- WiFi:
- Qualcomm Wi-Fi 7 (ath12k):
- extremely High Throughput (EHT) PHY support
- RealTek (rtl8xxxu):
- enable AP mode for: RTL8192FU, RTL8710BU (RTL8188GU),
RTL8192EU and RTL8723BU
- RealTek (rtw89):
- Introduce Time Averaged SAR (TAS) support
- Connector:
- support for event filtering
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=9CsR
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Increase size limits for to-be-sent skb frag allocations. This
allows tun, tap devices and packet sockets to better cope with
large writes operations
- Store netdevs in an xarray, to simplify iterating over netdevs
- Refactor nexthop selection for multipath routes
- Improve sched class lifetime handling
- Add backup nexthop ID support for bridge
- Implement drop reasons support in openvswitch
- Several data races annotations and fixes
- Constify the sk parameter of routing functions
- Prepend kernel version to netconsole message
Protocols:
- Implement support for TCP probing the peer being under memory
pressure
- Remove hard coded limitation on IPv6 specific info placement inside
the socket struct
- Get rid of sysctl_tcp_adv_win_scale and use an auto-estimated per
socket scaling factor
- Scaling-up the IPv6 expired route GC via a separated list of
expiring routes
- In-kernel support for the TLS alert protocol
- Better support for UDP reuseport with connected sockets
- Add NEXT-C-SID support for SRv6 End.X behavior, reducing the SR
header size
- Get rid of additional ancillary per MPTCP connection struct socket
- Implement support for BPF-based MPTCP packet schedulers
- Format MPTCP subtests selftests results in TAP
- Several new SMC 2.1 features including unique experimental options,
max connections per lgr negotiation, max links per lgr negotiation
BPF:
- Multi-buffer support in AF_XDP
- Add multi uprobe BPF links for attaching multiple uprobes and usdt
probes, which is significantly faster and saves extra fds
- Implement an fd-based tc BPF attach API (TCX) and BPF link support
on top of it
- Add SO_REUSEPORT support for TC bpf_sk_assign
- Support new instructions from cpu v4 to simplify the generated code
and feature completeness, for x86, arm64, riscv64
- Support defragmenting IPv(4|6) packets in BPF
- Teach verifier actual bounds of bpf_get_smp_processor_id() and fix
perf+libbpf issue related to custom section handling
- Introduce bpf map element count and enable it for all program types
- Add a BPF hook in sys_socket() to change the protocol ID from
IPPROTO_TCP to IPPROTO_MPTCP to cover migration for legacy
- Introduce bpf_me_mcache_free_rcu() and fix OOM under stress
- Add uprobe support for the bpf_get_func_ip helper
- Check skb ownership against full socket
- Support for up to 12 arguments in BPF trampoline
- Extend link_info for kprobe_multi and perf_event links
Netfilter:
- Speed-up process exit by aborting ruleset validation if a fatal
signal is pending
- Allow NLA_POLICY_MASK to be used with BE16/BE32 types
Driver API:
- Page pool optimizations, to improve data locality and cache usage
- Introduce ndo_hwtstamp_get() and ndo_hwtstamp_set() to avoid the
need for raw ioctl() handling in drivers
- Simplify genetlink dump operations (doit/dumpit) providing them the
common information already populated in struct genl_info
- Extend and use the yaml devlink specs to [re]generate the split ops
- Introduce devlink selective dumps, to allow SF filtering SF based
on handle and other attributes
- Add yaml netlink spec for netlink-raw families, allow route, link
and address related queries via the ynl tool
- Remove phylink legacy mode support
- Support offload LED blinking to phy
- Add devlink port function attributes for IPsec
New hardware / drivers:
- Ethernet:
- Broadcom ASP 2.0 (72165) ethernet controller
- MediaTek MT7988 SoC
- Texas Instruments AM654 SoC
- Texas Instruments IEP driver
- Atheros qca8081 phy
- Marvell 88Q2110 phy
- NXP TJA1120 phy
- WiFi:
- MediaTek mt7981 support
- Can:
- Kvaser SmartFusion2 PCI Express devices
- Allwinner T113 controllers
- Texas Instruments tcan4552/4553 chips
- Bluetooth:
- Intel Gale Peak
- Qualcomm WCN3988 and WCN7850
- NXP AW693 and IW624
- Mediatek MT2925
Drivers:
- Ethernet NICs:
- nVidia/Mellanox:
- mlx5:
- support UDP encapsulation in packet offload mode
- IPsec packet offload support in eswitch mode
- improve aRFS observability by adding new set of counters
- extends MACsec offload support to cover RoCE traffic
- dynamic completion EQs
- mlx4:
- convert to use auxiliary bus instead of custom interface
logic
- Intel
- ice:
- implement switchdev bridge offload, even for LAG
interfaces
- implement SRIOV support for LAG interfaces
- igc:
- add support for multiple in-flight TX timestamps
- Broadcom:
- bnxt:
- use the unified RX page pool buffers for XDP and non-XDP
- use the NAPI skb allocation cache
- OcteonTX2:
- support Round Robin scheduling HTB offload
- TC flower offload support for SPI field
- Freescale:
- add XDP_TX feature support
- AMD:
- ionic: add support for PCI FLR event
- sfc:
- basic conntrack offload
- introduce eth, ipv4 and ipv6 pedit offloads
- ST Microelectronics:
- stmmac: maximze PTP timestamping resolution
- Virtual NICs:
- Microsoft vNIC:
- batch ringing RX queue doorbell on receiving packets
- add page pool for RX buffers
- Virtio vNIC:
- add per queue interrupt coalescing support
- Google vNIC:
- add queue-page-list mode support
- Ethernet high-speed switches:
- nVidia/Mellanox (mlxsw):
- add port range matching tc-flower offload
- permit enslavement to netdevices with uppers
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- convert to phylink_pcs
- Renesas:
- r8A779fx: add speed change support
- rzn1: enables vlan support
- Ethernet PHYs:
- convert mv88e6xxx to phylink_pcs
- WiFi:
- Qualcomm Wi-Fi 7 (ath12k):
- extremely High Throughput (EHT) PHY support
- RealTek (rtl8xxxu):
- enable AP mode for: RTL8192FU, RTL8710BU (RTL8188GU),
RTL8192EU and RTL8723BU
- RealTek (rtw89):
- Introduce Time Averaged SAR (TAS) support
- Connector:
- support for event filtering"
* tag 'net-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1806 commits)
net: ethernet: mtk_wed: minor change in wed_{tx,rx}info_show
net: ethernet: mtk_wed: add some more info in wed_txinfo_show handler
net: stmmac: clarify difference between "interface" and "phy_interface"
r8152: add vendor/device ID pair for D-Link DUB-E250
devlink: move devlink_notify_register/unregister() to dev.c
devlink: move small_ops definition into netlink.c
devlink: move tracepoint definitions into core.c
devlink: push linecard related code into separate file
devlink: push rate related code into separate file
devlink: push trap related code into separate file
devlink: use tracepoint_enabled() helper
devlink: push region related code into separate file
devlink: push param related code into separate file
devlink: push resource related code into separate file
devlink: push dpipe related code into separate file
devlink: move and rename devlink_dpipe_send_and_alloc_skb() helper
devlink: push shared buffer related code into separate file
devlink: push port related code into separate file
devlink: push object register/unregister notifications into separate helpers
inet: fix IP_TRANSPARENT error handling
...
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCZOXpbgAKCRCRxhvAZXjc
oi8PAQCtXelGZHmTcmevsO8p4Qz7hFpkonZ/TnxKf+RdnlNgPgD+NWi+LoRBpaAj
xk4z8SqJaTTP4WXrG5JZ6o7EQkUL8gE=
=2e9I
-----END PGP SIGNATURE-----
Merge tag 'v6.6-vfs.super' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull superblock updates from Christian Brauner:
"This contains the super rework that was ready for this cycle. The
first part changes the order of how we open block devices and allocate
superblocks, contains various cleanups, simplifications, and a new
mechanism to wait on superblock state changes.
This unblocks work to ultimately limit the number of writers to a
block device. Jan has already scheduled follow-up work that will be
ready for v6.7 and allows us to restrict the number of writers to a
given block device. That series builds on this work right here.
The second part contains filesystem freezing updates.
Overview:
The generic superblock changes are rougly organized as follows
(ignoring additional minor cleanups):
(1) Removal of the bd_super member from struct block_device.
This was a very odd back pointer to struct super_block with
unclear rules. For all relevant places we have other means to get
the same information so just get rid of this.
(2) Simplify rules for superblock cleanup.
Roughly, everything that is allocated during fs_context
initialization and that's stored in fs_context->s_fs_info needs
to be cleaned up by the fs_context->free() implementation before
the superblock allocation function has been called successfully.
After sget_fc() returned fs_context->s_fs_info has been
transferred to sb->s_fs_info at which point sb->kill_sb() if
fully responsible for cleanup. Adhering to these rules means that
cleanup of sb->s_fs_info in fill_super() is to be avoided as it's
brittle and inconsistent.
Cleanup shouldn't be duplicated between sb->put_super() as
sb->put_super() is only called if sb->s_root has been set aka
when the filesystem has been successfully born (SB_BORN). That
complexity should be avoided.
This also means that block devices are to be closed in
sb->kill_sb() instead of sb->put_super(). More details in the
lower section.
(3) Make it possible to lookup or create a superblock before opening
block devices
There's a subtle dependency on (2) as some filesystems did rely
on fill_super() to be called in order to correctly clean up
sb->s_fs_info. All these filesystems have been fixed.
(4) Switch most filesystem to follow the same logic as the generic
mount code now does as outlined in (3).
(5) Use the superblock as the holder of the block device. We can now
easily go back from block device to owning superblock.
(6) Export and extend the generic fs_holder_ops and use them as
holder ops everywhere and remove the filesystem specific holder
ops.
(7) Call from the block layer up into the filesystem layer when the
block device is removed, allowing to shut down the filesystem
without risk of deadlocks.
(8) Get rid of get_super().
We can now easily go back from the block device to owning
superblock and can call up from the block layer into the
filesystem layer when the device is removed. So no need to wade
through all registered superblock to find the owning superblock
anymore"
Link: https://lore.kernel.org/lkml/20230824-prall-intakt-95dbffdee4a0@brauner/
* tag 'v6.6-vfs.super' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (47 commits)
super: use higher-level helper for {freeze,thaw}
super: wait until we passed kill super
super: wait for nascent superblocks
super: make locking naming consistent
super: use locking helpers
fs: simplify invalidate_inodes
fs: remove get_super
block: call into the file system for ioctl BLKFLSBUF
block: call into the file system for bdev_mark_dead
block: consolidate __invalidate_device and fsync_bdev
block: drop the "busy inodes on changed media" log message
dasd: also call __invalidate_device when setting the device offline
amiflop: don't call fsync_bdev in FDFMTBEG
floppy: call disk_force_media_change when changing the format
block: simplify the disk_force_media_change interface
nbd: call blk_mark_disk_dead in nbd_clear_sock_ioctl
xfs use fs_holder_ops for the log and RT devices
xfs: drop s_umount over opening the log and RT devices
ext4: use fs_holder_ops for the log device
ext4: drop s_umount over opening the log device
...
* Allow the kernel to initiate a freeze of a filesystem. The kernel
and userspace can both hold a freeze on a filesystem at the same
time; the freeze is not lifted until /both/ holders lift it. This
will enable us to fix a longstanding bug in XFS online fsck.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ2qTKExjcn+O1o2YRKO3ySh0YRpgUCZLVnJwAKCRBKO3ySh0YR
pqVIAP9u9CZEJ2Zcc7YpBj1MLUQGr2xBmz8RJEVJbQHKVgYcQwEA9BNb4eH4i2Af
K7Qp0OGNgyzZw37lN23Uf/SDuBK2QgM=
=seMl
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCZOXo2AAKCRCRxhvAZXjc
ojDfAQDguc2saF8WLeXtn2O0pGOW8vTrhpwiFHNI6hwdzf07/AD+LGBpFEqYKyX5
NHPzdR7YYpJoTsQzR4JFJVZqN9Q1xgU=
=wDq0
-----END PGP SIGNATURE-----
Merge tag 'vfs-6.6-merge-2' of ssh://gitolite.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull filesystem freezing updates from Darrick Wong:
New code for 6.6:
* Allow the kernel to initiate a freeze of a filesystem. The kernel
and userspace can both hold a freeze on a filesystem at the same
time; the freeze is not lifted until /both/ holders lift it. This
will enable us to fix a longstanding bug in XFS online fsck.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Message-Id: <20230822182604.GB11286@frogsfrogsfrogs>
Signed-off-by: Christian Brauner <brauner@kernel.org>
FDFMTBEG is used by fdformat to calibrate before formatting a disk.
Neither the atari nor PC floppy driver sync data, which also seems
a bit pointless for a disk hat is about to get formatted.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Message-Id: <20230811100828.1897174-11-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
While changing the format of a floppy isn't strictly speaking a media
change, the effects are the same in that the content of the media
changes and the diskseq should be increased and uevent should be
sent. Switch from calling __invalidate_device to
disk_force_media_change to do so.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Message-Id: <20230811100828.1897174-10-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Hard code the events to DISK_EVENT_MEDIA_CHANGE as that is the only
useful use case, and drop the superfluous return value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Message-Id: <20230811100828.1897174-9-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
nbd_clear_sock_ioctl kills the socket and with that the block
device. Instead of just invalidating file system buffers,
mark the device as dead, which will also invalidate the buffers
as part of the proper shutdown sequence. This also includes
invalidating partitions if there are any.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Message-Id: <20230811100828.1897174-8-hch@lst.de>
Signed-off-by: Christian Brauner <brauner@kernel.org>
There isn't any reason to not support REQ_OP_ZONE_RESET_ALL given everything
is actually handled in userspace, not mention it is pretty easy to support
RESET_ALL.
So enable REQ_OP_ZONE_RESET_ALL and let userspace handle it.
Verified by 'tools/zbc_reset_zone -all /dev/ublkb0' in libzbc[1] with
libublk-rs based ublk-zoned target prototype[2], follows command line
for creating ublk-zoned:
cargo run --example zoned -- add -1 1024 # add $dev_id $DEV_SIZE
[1] https://github.com/westerndigitalcorporation/libzbc
[2] https://github.com/ming1/libublk-rs/tree/zoned.v2
Cc: Niklas Cassel <Niklas.Cassel@wdc.com>
Cc: Damien Le Moal <dlemoal@kernel.org>
Cc: Andreas Hindborg <a.hindborg@samsung.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230810124326.321472-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=LnzH
-----END PGP SIGNATURE-----
Merge tag 'block-6.5-2023-08-19' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
"Main thing here is the fix for the regression in flush handling which
caused IO hangs/stalls for a few reporters. Hopefully that should all
be sorted out now. Outside of that, just a few minor fixes for issues
that were introduced in this cycle"
* tag 'block-6.5-2023-08-19' of git://git.kernel.dk/linux:
blk-mq: release scheduler resource when request completes
blk-crypto: dynamically allocate fallback profile
blk-cgroup: hold queue_lock when removing blkg->q_node
drivers/rnbd: restore sysfs interface to rnbd-client
Commit 137380c0ec renamed 'rnbd-client' to 'rnbd_client', this changed
sysfs interface to /sys/devices/virtual/rnbd_client/ctl/map_device
from /sys/devices/virtual/rnbd-client/ctl/map_device.
CC: Ivan Orlov <ivan.orlov0322@gmail.com>
CC: "Md. Haris Iqbal" <haris.iqbal@ionos.com>
CC: Jack Wang <jinpu.wang@ionos.com>
Fixes: 137380c0ec ("block/rnbd: make all 'class' structures const")
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20230816022210.2501228-1-lizhijian@fujitsu.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/sfc/tc.c
fa165e1949 ("sfc: don't unregister flow_indr if it was never registered")
3bf969e88a ("sfc: add MAE table machinery for conntrack table")
https://lore.kernel.org/all/20230818112159.7430e9b4@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 137380c0ec renamed 'rnbd-client' to 'rnbd_client', this changed
sysfs interface to /sys/devices/virtual/rnbd_client/ctl/map_device
from /sys/devices/virtual/rnbd-client/ctl/map_device.
CC: Ivan Orlov <ivan.orlov0322@gmail.com>
CC: "Md. Haris Iqbal" <haris.iqbal@ionos.com>
CC: Jack Wang <jinpu.wang@ionos.com>
Fixes: 137380c0ec ("block/rnbd: make all 'class' structures const")
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20230816022210.2501228-1-lizhijian@fujitsu.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Only three families use info->userhdr today and going forward
we discourage using fixed headers in new families.
So having the pointer to user header in struct genl_info
is an overkill. Compute the header pointer at runtime.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/20230814214723.2924989-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use memdup_user_nul() helper instead of open-coding
to simplify the code.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230815114815.1551171-1-ruanjinjie@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=+1Vt
-----END PGP SIGNATURE-----
Merge tag 'block-6.5-2023-08-11' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- Fixes for request_queue state (Ming)
- Another uuid quirk (August)
- RCU poll fix for NVMe (Ming)
- Fix for an IO stall with polled IO (me)
- Fix for blk-iocost stats enable/disable accounting (Chengming)
- Regression fix for large pages for zram (Christoph)
* tag 'block-6.5-2023-08-11' of git://git.kernel.dk/linux:
nvme: core: don't hold rcu read lock in nvme_ns_chr_uring_cmd_iopoll
blk-iocost: fix queue stats accounting
block: don't make REQ_POLLED imply REQ_NOWAIT
block: get rid of unused plug->nowait flag
zram: take device and not only bvec offset into account
nvme-pci: add NVME_QUIRK_BOGUS_NID for Samsung PM9B1 256G and 512G
nvme-rdma: fix potential unbalanced freeze & unfreeze
nvme-tcp: fix potential unbalanced freeze & unfreeze
nvme: fix possible hang when removing a controller during error recovery
The added check of 'req_op(req) == REQ_OP_ZONE_APPEND' should have been
done after the request is confirmed as valid.
Actually here, the request should always been true, so add one
WARN_ON_ONCE(!req), meantime move the zone_append check after
checking the request.
Cc: Andreas Hindborg <a.hindborg@samsung.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 29802d7ca3 ("ublk: enable zoned storage support")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230811135216.420404-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is the module init function, which by definition is used only
locally, so mark it static to avoid a warning:
drivers/block/swim3.c:1280:5: error: no previous prototype for 'swim3_init' [-Werror=missing-prototypes]
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are two warnings reported by smatch:
drivers/block/ublk_drv.c:445 ublk_setup_iod_zoned() warn:
signedness bug returning '(-95)'
drivers/block/ublk_drv.c:963 ublk_setup_iod() warn:
signedness bug returning '(-5)'
The type of "blk_status_t" is either be a u32 or u8, but this two
functions return a negative value when not supported or failed. Use
the error code of the blk module to fix these warnings.
Fixes: 29802d7ca3 ("ublk: enable zoned storage support")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202308100201.TCRhgdvN-lkp@intel.com/
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230810084836.3535322-1-lizetao1@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add zoned storage support to ublk: report_zones and operations:
- REQ_OP_ZONE_OPEN
- REQ_OP_ZONE_CLOSE
- REQ_OP_ZONE_FINISH
- REQ_OP_ZONE_RESET
- REQ_OP_ZONE_APPEND
The zone append feature uses the `addr` field of `struct ublksrv_io_cmd` to
communicate ALBA back to the kernel. Therefore ublk must be used with the
user copy feature (UBLK_F_USER_COPY) for zoned storage support to be
available. Without this feature, ublk will not allow zoned storage support.
Signed-off-by: Andreas Hindborg <a.hindborg@samsung.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230804114610.179530-4-nmi@metaspace.dk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In preparation for zoned storage support, move the check for empty `addr`
field into the command handler case statement. Note that the check makes no
sense for `UBLK_IO_NEED_GET_DATA` because the `addr` field must always be
set for this command.
Signed-off-by: Andreas Hindborg <a.hindborg@samsung.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230804114610.179530-3-nmi@metaspace.dk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This will be used by ublk zoned storage support.
Signed-off-by: Andreas Hindborg <a.hindborg@samsung.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20230804114610.179530-2-nmi@metaspace.dk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit af8b04c637 ("zram: simplify bvec iteration in
__zram_make_request") changed the bio iteration in zram to rely on the
implicit capping to page boundaries in bio_for_each_segment. But it
failed to care for the fact zram not only care about the page alignment
of the bio payload, but also the page alignment into the device. For
buffered I/O and swap those are the same, but for direct I/O or kernel
internal I/O like XFS log buffer writes they can differ.
Fix this by open coding bio_for_each_segment and limiting the bvec len
so that it never crosses over a page alignment boundary in the device
in addition to the payload boundary already taken care of by
bio_iter_iovec.
Cc: stable@vger.kernel.org
Fixes: af8b04c637 ("zram: simplify bvec iteration in __zram_make_request")
Reported-by: Dusty Mabe <dusty@dustymabe.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Link: https://lore.kernel.org/r/20230805055537.147835-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Due to rbd_try_acquire_lock() effectively swallowing all but
EBLOCKLISTED error from rbd_try_lock() ("request lock anyway") and
rbd_request_lock() returning ETIMEDOUT error not only for an actual
notify timeout but also when the lock owner doesn't respond, a busy
loop inside of rbd_acquire_lock() between rbd_try_acquire_lock() and
rbd_request_lock() is possible.
Requesting the lock on EBUSY error (returned by get_lock_owner_info()
if an incompatible lock or invalid lock owner is detected) makes very
little sense. The same goes for ETIMEDOUT error (might pop up pretty
much anywhere if osd_request_timeout option is set) and many others.
Just fail I/O requests on rbd_dev->acquiring_list immediately on any
error from rbd_try_lock().
Cc: stable@vger.kernel.org # 588159009d5b: rbd: retrieve and check lock owner twice before blocklisting
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
blocklisting (fencing) with a couple of prerequisites and a fixup to
prevent metrics from being sent to the MDS even just once after that
has been disabled by the user. All marked for stable.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmTD7MgTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi3SBB/4nHdfSQwy0z2+PM766sUKxSlmaRw8X
4AJyGAIGj5BnHHhtluwLpEYfrh3wfyCRaNYgS64jdsudbUBxPKIIWn2lEFxtyWbC
w0R2uEc+NGJLJOYfJ+lBP06Q2r6qk7N6OGNy6qLaN+v6xJ8WPw7H3fJBLVhnPgMq
7lkACRN+0P5Xt6ZJ57kbWWiFQ+vjv7bbDa0P9zMl6uCgoYsIpvrskqygx+gHbdsq
IcnpsHu3F0ycYAJT5eJ5GcCcThvwbNjWdbJy1fERah7U/LNcX/S3To9V5LPmydOQ
tYAWMlC/1a99fr+jTYF0Pu5GLUdK0UMKeX04ZN3SKON4pORurpypw3n8
=rw72
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-6.5-rc4' of https://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A patch to reduce the potential for erroneous RBD exclusive lock
blocklisting (fencing) with a couple of prerequisites and a fixup to
prevent metrics from being sent to the MDS even just once after that
has been disabled by the user. All marked for stable"
* tag 'ceph-for-6.5-rc4' of https://github.com/ceph/ceph-client:
rbd: retrieve and check lock owner twice before blocklisting
rbd: harden get_lock_owner_info() a bit
rbd: make get_lock_owner_info() return a single locker or NULL
ceph: never send metrics if disable_send_metrics is set
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAmTD2VcQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpqzgEADT9lc0fr8wnp2fu/7NhkdsaPtuoUKiH7ju
qxWExXIzxxKYM6OdCdYho9SvIjtdblraZOGqrEni8KMcKnR6vDd8BjGzPJ2BJQe2
GhU0VLVqAw2uoaLhWIZ3m+CyKn7rggoCwpTAUFQG7vL6vSW+ExkWs6g4XcrWhq5V
XCPJnNRc2o6OdFnv1xBNy1YRrP2ME+HaghJdDNxVM4R9hOv4PVvYrW7P2fK1gurD
o3JgTAQg6//16ZBAMcZDkwuGGFVdvG16EiE/0z3QdP4WeDqSFqqxYtk8m/LqAx31
FswUI+YDmKJHSfbLCh6pW4j81xH+svVi0LiANdlxCMGg3zouft+wh/KGdQJC/rcb
ocFgUCOL4P4208wXkuUjtcAI0zmEMPAIoRQirOzDExja0bI4LJrp3GKJ78U4MbDo
iBM5qgkH+MqwD/jXMOY5MnEEBzqceW7Q5Al6emE093kRenIYulEL6ZFy05vfqG1+
NuQcvSJ9f0mgTDUGr0bXytshTG4vSHtKZ9UfAgh5FzPBnPYpwRbxlq6i/7+DxU6k
33FTzNLuRwDSEo33Uj75KwK1glizofYj6lrqYxVw/9jkVAEEzpjr6H8Su1+dTt8L
ZbXSQKdxsAxGdbIMeA1lUfUmqQHi1ouTLsBzwkceKCeN3UXmzGOnNBXmvoVXSv0A
v4RNV+WHCA==
=TD54
-----END PGP SIGNATURE-----
Merge tag 'block-6.5-2023-07-28' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
"A few fixes that should go into the current kernel release, mainly:
- Set of fixes for dasd (Stefan)
- Handle interruptible waits returning because of a signal for ublk
(Ming)"
* tag 'block-6.5-2023-07-28' of git://git.kernel.dk/linux:
ublk: return -EINTR if breaking from waiting for existed users in DEL_DEV
ublk: fail to recover device if queue setup is interrupted
ublk: fail to start device if queue setup is interrupted
block: Fix a source code comment in include/uapi/linux/blkzoned.h
s390/dasd: print copy pair message only for the correct error
s390/dasd: fix hanging device after request requeue
s390/dasd: use correct number of retries for ERP requests
s390/dasd: fix hanging device after quiesce/resume
If user interrupts wait_event_interruptible() in ublk_ctrl_del_dev(),
return -EINTR and let user know what happens.
Fixes: 0abe39dec0 ("block: ublk: improve handling device deletion")
Reported-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20230726144502.566785-4-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In ublk_ctrl_end_recovery(), if wait_for_completion_interruptible() is
interrupted by signal, queues aren't setup successfully yet, so we
have to fail UBLK_CMD_END_USER_RECOVERY, otherwise kernel oops can be
triggered.
Fixes: c732a852b4 ("ublk_drv: add START_USER_RECOVERY and END_USER_RECOVERY support")
Reported-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20230726144502.566785-3-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In ublk_ctrl_start_dev(), if wait_for_completion_interruptible() is
interrupted by signal, queues aren't setup successfully yet, so we
have to fail UBLK_CMD_START_DEV, otherwise kernel oops can be triggered.
Reported by German when working on qemu-storage-deamon which requires
single thread ublk daemon.
Fixes: 71f28f3136 ("ublk_drv: add io_uring based userspace block driver")
Reported-by: German Maglione <gmaglione@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230726144502.566785-2-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
An attempt to acquire exclusive lock can race with the current lock
owner closing the image:
1. lock is held by client123, rbd_lock() returns -EBUSY
2. get_lock_owner_info() returns client123 instance details
3. client123 closes the image, lock is released
4. find_watcher() returns 0 as there is no matching watcher anymore
5. client123 instance gets erroneously blocklisted
Particularly impacted is mirror snapshot scheduler in snapshot-based
mirroring since it happens to open and close images a lot (images are
opened only for as long as it takes to take the next mirror snapshot,
the same client instance is used for all images).
To reduce the potential for erroneous blocklisting, retrieve the lock
owner again after find_watcher() returns 0. If it's still there, make
sure it matches the previously detected lock owner.
Cc: stable@vger.kernel.org # f38cb9d9c204: rbd: make get_lock_owner_info() return a single locker or NULL
Cc: stable@vger.kernel.org # 8ff2c64c9765: rbd: harden get_lock_owner_info() a bit
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
- we want the exclusive lock type, so test for it directly
- use sscanf() to actually parse the lock cookie and avoid admitting
invalid handles
- bail if locker has a blank address
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
Make the "num_lockers can be only 0 or 1" assumption explicit and
simplify the API by getting rid of output parameters in preparation
for calling get_lock_owner_info() twice before blocklisting.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
-----BEGIN PGP SIGNATURE-----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=e2OR
-----END PGP SIGNATURE-----
Merge tag 'block-6.5-2023-07-21' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- Fix for loop regressions (Mauricio)
- Fix a potential stall with batched wakeups in sbitmap (David)
- Fix for stall with recursive plug flushes (Ross)
- Skip accounting of empty requests for blk-iocost (Chengming)
- Remove a dead field in struct blk_mq_hw_ctx (Chengming)
* tag 'block-6.5-2023-07-21' of git://git.kernel.dk/linux:
loop: do not enforce max_loop hard limit by (new) default
loop: deprecate autoloading callback loop_probe()
sbitmap: fix batching wakeup
blk-iocost: skip empty flush bio in iocost
blk-mq: delete dead struct blk_mq_hw_ctx->queued field
blk-mq: Fix stall due to recursive flush plug
Problem:
The max_loop parameter is used for 2 different purposes:
1) initial number of loop devices to pre-create on init
2) maximum number of loop devices to add on access/open()
Historically, its default value (zero) caused 1) to create non-zero
number of devices (CONFIG_BLK_DEV_LOOP_MIN_COUNT), and no hard limit on
2) to add devices with autoloading.
However, the default value changed in commit 85c5019771 ("loop: Fix
the max_loop commandline argument treatment when it is set to 0") to
CONFIG_BLK_DEV_LOOP_MIN_COUNT, for max_loop=0 not to pre-create devices.
That does improve 1), but unfortunately it breaks 2), as the default
behavior changed from no-limit to hard-limit.
Example:
For example, this userspace code broke for N >= CONFIG, if the user
relied on the default value 0 for max_loop:
mknod("/dev/loopN");
open("/dev/loopN"); // now fails with ENXIO
Though affected users may "fix" it with (loop.)max_loop=0, this means to
require a kernel parameter change on stable kernel update (that commit
Fixes: an old commit in stable).
Solution:
The original semantics for the default value in 2) can be applied if the
parameter is not set (ie, default behavior).
This still keeps the intended function in 1) and 2) if set, and that
commit's intended improvement in 1) if max_loop=0.
Before 85c50197716c:
- default: 1) CONFIG devices 2) no limit
- max_loop=0: 1) CONFIG devices 2) no limit
- max_loop=X: 1) X devices 2) X limit
After 85c50197716c:
- default: 1) CONFIG devices 2) CONFIG limit (*)
- max_loop=0: 1) 0 devices (*) 2) no limit
- max_loop=X: 1) X devices 2) X limit
This commit:
- default: 1) CONFIG devices 2) no limit (*)
- max_loop=0: 1) 0 devices 2) no limit
- max_loop=X: 1) X devices 2) X limit
Future:
The issue/regression from that commit only affects code under the
CONFIG_BLOCK_LEGACY_AUTOLOAD deprecation guard, thus the fix too is
contained under it.
Once that deprecated functionality/code is removed, the purpose 2) of
max_loop (hard limit) is no longer in use, so the module parameter
description can be changed then.
Tests:
Linux 6.4-rc7
CONFIG_BLK_DEV_LOOP_MIN_COUNT=8
CONFIG_BLOCK_LEGACY_AUTOLOAD=y
- default (original)
# ls -1 /dev/loop*
/dev/loop-control
/dev/loop0
...
/dev/loop7
# ./test-loop
open: /dev/loop8: No such device or address
- default (patched)
# ls -1 /dev/loop*
/dev/loop-control
/dev/loop0
...
/dev/loop7
# ./test-loop
#
- max_loop=0 (original & patched):
# ls -1 /dev/loop*
/dev/loop-control
# ./test-loop
#
- max_loop=8 (original & patched):
# ls -1 /dev/loop*
/dev/loop-control
/dev/loop0
...
/dev/loop7
# ./test-loop
open: /dev/loop8: No such device or address
- max_loop=0 (patched; CONFIG_BLOCK_LEGACY_AUTOLOAD is not set)
# ls -1 /dev/loop*
/dev/loop-control
# ./test-loop
open: /dev/loop8: No such device or address
Fixes: 85c5019771 ("loop: Fix the max_loop commandline argument treatment when it is set to 0")
Signed-off-by: Mauricio Faria de Oliveira <mfo@canonical.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230720143033.841001-3-mfo@canonical.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The 'probe' callback in __register_blkdev() is only used under the
CONFIG_BLOCK_LEGACY_AUTOLOAD deprecation guard.
The loop_probe() function is only used for that callback, so guard it
too, accordingly.
See commit fbdee71bb5 ("block: deprecate autoloading based on dev_t").
Signed-off-by: Mauricio Faria de Oliveira <mfo@canonical.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230720143033.841001-2-mfo@canonical.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a module alias to nbd.ko that allows the generic netlink core to
automatically load the module when netlink messages for nbd are
received.
This frees the user from manually having to load the module before using
nbd functionality via netlink.
If the system policy allows it this can even be used to load the nbd
module from containers which would otherwise not have access to the
necessary module files to do a normal "modprobe nbd".
For example this avoids the following error when using nbd-client:
$ nbd-client localhost 10809 /dev/nbd0
...
Error: Couldn't resolve the nbd netlink family, make sure the nbd module is loaded and your nbd driver supports the netlink interface.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Josef Bacik <josef@toxicpadna.com>
Link: https://lore.kernel.org/r/20230713-b4-nbd-genl-v3-1-226cbddba04b@weissschuh.net
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In virtblk_probe_zoned_device(), execute blk_queue_chunk_sectors() and
blk_queue_max_zone_append_sectors() to respectively set the zoned device
zone size and maximum zone append sector limit before executing
blk_revalidate_disk_zones(). This is to allow the block layer zone
reavlidation to check these device characteristics prior to checking all
zones of the device.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20230703024812.76778-5-dlemoal@kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In null_register_zoned_dev(), execute blk_queue_chunk_sectors() and
blk_queue_max_zone_append_sectors() to respectively set the zoned device
zone size and maximum zone append sector limit before executing
blk_revalidate_disk_zones(). This is to allow the block layer zone
reavlidation to check these device characteristics prior to checking all
zones of the device.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20230703024812.76778-4-dlemoal@kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Core
----
- Rework the sendpage & splice implementations. Instead of feeding
data into sockets page by page extend sendmsg handlers to support
taking a reference on the data, controlled by a new flag called
MSG_SPLICE_PAGES. Rework the handling of unexpected-end-of-file
to invoke an additional callback instead of trying to predict what
the right combination of MORE/NOTLAST flags is.
Remove the MSG_SENDPAGE_NOTLAST flag completely.
- Implement SCM_PIDFD, a new type of CMSG type analogous to
SCM_CREDENTIALS, but it contains pidfd instead of plain pid.
- Enable socket busy polling with CONFIG_RT.
- Improve reliability and efficiency of reporting for ref_tracker.
- Auto-generate a user space C library for various Netlink families.
Protocols
---------
- Allow TCP to shrink the advertised window when necessary, prevent
sk_rcvbuf auto-tuning from growing the window all the way up to
tcp_rmem[2].
- Use per-VMA locking for "page-flipping" TCP receive zerocopy.
- Prepare TCP for device-to-device data transfers, by making sure
that payloads are always attached to skbs as page frags.
- Make the backoff time for the first N TCP SYN retransmissions
linear. Exponential backoff is unnecessarily conservative.
- Create a new MPTCP getsockopt to retrieve all info (MPTCP_FULL_INFO).
- Avoid waking up applications using TLS sockets until we have
a full record.
- Allow using kernel memory for protocol ioctl callbacks, paving
the way to issuing ioctls over io_uring.
- Add nolocalbypass option to VxLAN, forcing packets to be fully
encapsulated even if they are destined for a local IP address.
- Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
in-kernel ECMP implementation (e.g. Open vSwitch) select the same
link for all packets. Support L4 symmetric hashing in Open vSwitch.
- PPPoE: make number of hash bits configurable.
- Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
(ipconfig).
- Add layer 2 miss indication and filtering, allowing higher layers
(e.g. ACL filters) to make forwarding decisions based on whether
packet matched forwarding state in lower devices (bridge).
- Support matching on Connectivity Fault Management (CFM) packets.
- Hide the "link becomes ready" IPv6 messages by demoting their
printk level to debug.
- HSR: don't enable promiscuous mode if device offloads the proto.
- Support active scanning in IEEE 802.15.4.
- Continue work on Multi-Link Operation for WiFi 7.
BPF
---
- Add precision propagation for subprogs and callbacks. This allows
maintaining verification efficiency when subprograms are used,
or in fact passing the verifier at all for complex programs,
especially those using open-coded iterators.
- Improve BPF's {g,s}setsockopt() length handling. Previously BPF
assumed the length is always equal to the amount of written data.
But some protos allow passing a NULL buffer to discover what
the output buffer *should* be, without writing anything.
- Accept dynptr memory as memory arguments passed to helpers.
- Add routing table ID to bpf_fib_lookup BPF helper.
- Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands.
- Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
maps as read-only).
- Show target_{obj,btf}_id in tracing link fdinfo.
- Addition of several new kfuncs (most of the names are self-explanatory):
- Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
and bpf_dynptr_clone().
- bpf_task_under_cgroup()
- bpf_sock_destroy() - force closing sockets
- bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs
Netfilter
---------
- Relax set/map validation checks in nf_tables. Allow checking
presence of an entry in a map without using the value.
- Increase ip_vs_conn_tab_bits range for 64BIT builds.
- Allow updating size of a set.
- Improve NAT tuple selection when connection is closing.
Driver API
----------
- Integrate netdev with LED subsystem, to allow configuring HW
"offloaded" blinking of LEDs based on link state and activity
(i.e. packets coming in and out).
- Support configuring rate selection pins of SFP modules.
- Factor Clause 73 auto-negotiation code out of the drivers, provide
common helper routines.
- Add more fool-proof helpers for managing lifetime of MDIO devices
associated with the PCS layer.
- Allow drivers to report advanced statistics related to Time Aware
scheduler offload (taprio).
- Allow opting out of VF statistics in link dump, to allow more VFs
to fit into the message.
- Split devlink instance and devlink port operations.
New hardware / drivers
----------------------
- Ethernet:
- Synopsys EMAC4 IP support (stmmac)
- Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
- Marvell 88E6250 7 port switches
- Microchip LAN8650/1 Rev.B0 PHYs
- MediaTek MT7981/MT7988 built-in 1GE PHY driver
- WiFi:
- Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
- Realtek RTL8723DS (SDIO variant)
- Realtek RTL8851BE
- CAN:
- Fintek F81604
Drivers
-------
- Ethernet NICs:
- Intel (100G, ice):
- support dynamic interrupt allocation
- use meta data match instead of VF MAC addr on slow-path
- nVidia/Mellanox:
- extend link aggregation to handle 4, rather than just 2 ports
- spawn sub-functions without any features by default
- OcteonTX2:
- support HTB (Tx scheduling/QoS) offload
- make RSS hash generation configurable
- support selecting Rx queue using TC filters
- Wangxun (ngbe/txgbe):
- add basic Tx/Rx packet offloads
- add phylink support (SFP/PCS control)
- Freescale/NXP (enetc):
- report TAPRIO packet statistics
- Solarflare/AMD:
- support matching on IP ToS and UDP source port of outer header
- VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
- add devlink dev info support for EF10
- Virtual NICs:
- Microsoft vNIC:
- size the Rx indirection table based on requested configuration
- support VLAN tagging
- Amazon vNIC:
- try to reuse Rx buffers if not fully consumed, useful for ARM
servers running with 16kB pages
- Google vNIC:
- support TCP segmentation of >64kB frames
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- enable USXGMII (88E6191X)
- Microchip:
- lan966x: add support for Egress Stage 0 ACL engine
- lan966x: support mapping packet priority to internal switch
priority (based on PCP or DSCP)
- Ethernet PHYs:
- Broadcom PHYs:
- support for Wake-on-LAN for BCM54210E/B50212E
- report LPI counter
- Microsemi PHYs: support RGMII delay configuration (VSC85xx)
- Micrel PHYs: receive timestamp in the frame (LAN8841)
- Realtek PHYs: support optional external PHY clock
- Altera TSE PCS: merge the driver into Lynx PCS which it is
a variant of
- CAN: Kvaser PCIEcan:
- support packet timestamping
- WiFi:
- Intel (iwlwifi):
- major update for new firmware and Multi-Link Operation (MLO)
- configuration rework to drop test devices and split
the different families
- support for segmented PNVM images and power tables
- new vendor entries for PPAG (platform antenna gain) feature
- Qualcomm 802.11ax (ath11k):
- Multiple Basic Service Set Identifier (MBSSID) and
Enhanced MBSSID Advertisement (EMA) support in AP mode
- support factory test mode
- RealTek (rtw89):
- add RSSI based antenna diversity
- support U-NII-4 channels on 5 GHz band
- RealTek (rtl8xxxu):
- AP mode support for 8188f
- support USB RX aggregation for the newer chips
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=9i4I
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking changes from Jakub Kicinski:
"WiFi 7 and sendpage changes are the biggest pieces of work for this
release. The latter will definitely require fixes but I think that we
got it to a reasonable point.
Core:
- Rework the sendpage & splice implementations
Instead of feeding data into sockets page by page extend sendmsg
handlers to support taking a reference on the data, controlled by a
new flag called MSG_SPLICE_PAGES
Rework the handling of unexpected-end-of-file to invoke an
additional callback instead of trying to predict what the right
combination of MORE/NOTLAST flags is
Remove the MSG_SENDPAGE_NOTLAST flag completely
- Implement SCM_PIDFD, a new type of CMSG type analogous to
SCM_CREDENTIALS, but it contains pidfd instead of plain pid
- Enable socket busy polling with CONFIG_RT
- Improve reliability and efficiency of reporting for ref_tracker
- Auto-generate a user space C library for various Netlink families
Protocols:
- Allow TCP to shrink the advertised window when necessary, prevent
sk_rcvbuf auto-tuning from growing the window all the way up to
tcp_rmem[2]
- Use per-VMA locking for "page-flipping" TCP receive zerocopy
- Prepare TCP for device-to-device data transfers, by making sure
that payloads are always attached to skbs as page frags
- Make the backoff time for the first N TCP SYN retransmissions
linear. Exponential backoff is unnecessarily conservative
- Create a new MPTCP getsockopt to retrieve all info
(MPTCP_FULL_INFO)
- Avoid waking up applications using TLS sockets until we have a full
record
- Allow using kernel memory for protocol ioctl callbacks, paving the
way to issuing ioctls over io_uring
- Add nolocalbypass option to VxLAN, forcing packets to be fully
encapsulated even if they are destined for a local IP address
- Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
in-kernel ECMP implementation (e.g. Open vSwitch) select the same
link for all packets. Support L4 symmetric hashing in Open vSwitch
- PPPoE: make number of hash bits configurable
- Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
(ipconfig)
- Add layer 2 miss indication and filtering, allowing higher layers
(e.g. ACL filters) to make forwarding decisions based on whether
packet matched forwarding state in lower devices (bridge)
- Support matching on Connectivity Fault Management (CFM) packets
- Hide the "link becomes ready" IPv6 messages by demoting their
printk level to debug
- HSR: don't enable promiscuous mode if device offloads the proto
- Support active scanning in IEEE 802.15.4
- Continue work on Multi-Link Operation for WiFi 7
BPF:
- Add precision propagation for subprogs and callbacks. This allows
maintaining verification efficiency when subprograms are used, or
in fact passing the verifier at all for complex programs,
especially those using open-coded iterators
- Improve BPF's {g,s}setsockopt() length handling. Previously BPF
assumed the length is always equal to the amount of written data.
But some protos allow passing a NULL buffer to discover what the
output buffer *should* be, without writing anything
- Accept dynptr memory as memory arguments passed to helpers
- Add routing table ID to bpf_fib_lookup BPF helper
- Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands
- Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
maps as read-only)
- Show target_{obj,btf}_id in tracing link fdinfo
- Addition of several new kfuncs (most of the names are
self-explanatory):
- Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
and bpf_dynptr_clone().
- bpf_task_under_cgroup()
- bpf_sock_destroy() - force closing sockets
- bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs
Netfilter:
- Relax set/map validation checks in nf_tables. Allow checking
presence of an entry in a map without using the value
- Increase ip_vs_conn_tab_bits range for 64BIT builds
- Allow updating size of a set
- Improve NAT tuple selection when connection is closing
Driver API:
- Integrate netdev with LED subsystem, to allow configuring HW
"offloaded" blinking of LEDs based on link state and activity
(i.e. packets coming in and out)
- Support configuring rate selection pins of SFP modules
- Factor Clause 73 auto-negotiation code out of the drivers, provide
common helper routines
- Add more fool-proof helpers for managing lifetime of MDIO devices
associated with the PCS layer
- Allow drivers to report advanced statistics related to Time Aware
scheduler offload (taprio)
- Allow opting out of VF statistics in link dump, to allow more VFs
to fit into the message
- Split devlink instance and devlink port operations
New hardware / drivers:
- Ethernet:
- Synopsys EMAC4 IP support (stmmac)
- Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
- Marvell 88E6250 7 port switches
- Microchip LAN8650/1 Rev.B0 PHYs
- MediaTek MT7981/MT7988 built-in 1GE PHY driver
- WiFi:
- Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
- Realtek RTL8723DS (SDIO variant)
- Realtek RTL8851BE
- CAN:
- Fintek F81604
Drivers:
- Ethernet NICs:
- Intel (100G, ice):
- support dynamic interrupt allocation
- use meta data match instead of VF MAC addr on slow-path
- nVidia/Mellanox:
- extend link aggregation to handle 4, rather than just 2 ports
- spawn sub-functions without any features by default
- OcteonTX2:
- support HTB (Tx scheduling/QoS) offload
- make RSS hash generation configurable
- support selecting Rx queue using TC filters
- Wangxun (ngbe/txgbe):
- add basic Tx/Rx packet offloads
- add phylink support (SFP/PCS control)
- Freescale/NXP (enetc):
- report TAPRIO packet statistics
- Solarflare/AMD:
- support matching on IP ToS and UDP source port of outer
header
- VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
- add devlink dev info support for EF10
- Virtual NICs:
- Microsoft vNIC:
- size the Rx indirection table based on requested
configuration
- support VLAN tagging
- Amazon vNIC:
- try to reuse Rx buffers if not fully consumed, useful for ARM
servers running with 16kB pages
- Google vNIC:
- support TCP segmentation of >64kB frames
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- enable USXGMII (88E6191X)
- Microchip:
- lan966x: add support for Egress Stage 0 ACL engine
- lan966x: support mapping packet priority to internal switch
priority (based on PCP or DSCP)
- Ethernet PHYs:
- Broadcom PHYs:
- support for Wake-on-LAN for BCM54210E/B50212E
- report LPI counter
- Microsemi PHYs: support RGMII delay configuration (VSC85xx)
- Micrel PHYs: receive timestamp in the frame (LAN8841)
- Realtek PHYs: support optional external PHY clock
- Altera TSE PCS: merge the driver into Lynx PCS which it is a
variant of
- CAN: Kvaser PCIEcan:
- support packet timestamping
- WiFi:
- Intel (iwlwifi):
- major update for new firmware and Multi-Link Operation (MLO)
- configuration rework to drop test devices and split the
different families
- support for segmented PNVM images and power tables
- new vendor entries for PPAG (platform antenna gain) feature
- Qualcomm 802.11ax (ath11k):
- Multiple Basic Service Set Identifier (MBSSID) and Enhanced
MBSSID Advertisement (EMA) support in AP mode
- support factory test mode
- RealTek (rtw89):
- add RSSI based antenna diversity
- support U-NII-4 channels on 5 GHz band
- RealTek (rtl8xxxu):
- AP mode support for 8188f
- support USB RX aggregation for the newer chips"
* tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1602 commits)
net: scm: introduce and use scm_recv_unix helper
af_unix: Skip SCM_PIDFD if scm->pid is NULL.
net: lan743x: Simplify comparison
netlink: Add __sock_i_ino() for __netlink_diag_dump().
net: dsa: avoid suspicious RCU usage for synced VLAN-aware MAC addresses
Revert "af_unix: Call scm_recv() only after scm_set_cred()."
phylink: ReST-ify the phylink_pcs_neg_mode() kdoc
libceph: Partially revert changes to support MSG_SPLICE_PAGES
net: phy: mscc: fix packet loss due to RGMII delays
net: mana: use vmalloc_array and vcalloc
net: enetc: use vmalloc_array and vcalloc
ionic: use vmalloc_array and vcalloc
pds_core: use vmalloc_array and vcalloc
gve: use vmalloc_array and vcalloc
octeon_ep: use vmalloc_array and vcalloc
net: usb: qmi_wwan: add u-blox 0x1312 composition
perf trace: fix MSG_SPLICE_PAGES build error
ipvlan: Fix return value of ipvlan_queue_xmit()
netfilter: nf_tables: fix underflow in chain reference counter
netfilter: nf_tables: unbind non-anonymous set if rule construction fails
...
- Yosry has also eliminated cgroup's atomic rstat flushing.
- Nhat Pham adds the new cachestat() syscall. It provides userspace
with the ability to query pagecache status - a similar concept to
mincore() but more powerful and with improved usability.
- Mel Gorman provides more optimizations for compaction, reducing the
prevalence of page rescanning.
- Lorenzo Stoakes has done some maintanance work on the get_user_pages()
interface.
- Liam Howlett continues with cleanups and maintenance work to the maple
tree code. Peng Zhang also does some work on maple tree.
- Johannes Weiner has done some cleanup work on the compaction code.
- David Hildenbrand has contributed additional selftests for
get_user_pages().
- Thomas Gleixner has contributed some maintenance and optimization work
for the vmalloc code.
- Baolin Wang has provided some compaction cleanups,
- SeongJae Park continues maintenance work on the DAMON code.
- Huang Ying has done some maintenance on the swap code's usage of
device refcounting.
- Christoph Hellwig has some cleanups for the filemap/directio code.
- Ryan Roberts provides two patch series which yield some
rationalization of the kernel's access to pte entries - use the provided
APIs rather than open-coding accesses.
- Lorenzo Stoakes has some fixes to the interaction between pagecache
and directio access to file mappings.
- John Hubbard has a series of fixes to the MM selftesting code.
- ZhangPeng continues the folio conversion campaign.
- Hugh Dickins has been working on the pagetable handling code, mainly
with a view to reducing the load on the mmap_lock.
- Catalin Marinas has reduced the arm64 kmalloc() minimum alignment from
128 to 8.
- Domenico Cerasuolo has improved the zswap reclaim mechanism by
reorganizing the LRU management.
- Matthew Wilcox provides some fixups to make gfs2 work better with the
buffer_head code.
- Vishal Moola also has done some folio conversion work.
- Matthew Wilcox has removed the remnants of the pagevec code - their
functionality is migrated over to struct folio_batch.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZJejewAKCRDdBJ7gKXxA
joggAPwKMfT9lvDBEUnJagY7dbDPky1cSYZdJKxxM2cApGa42gEA6Cl8HRAWqSOh
J0qXCzqaaN8+BuEyLGDVPaXur9KirwY=
=B7yQ
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2023-06-24-19-15' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull mm updates from Andrew Morton:
- Yosry Ahmed brought back some cgroup v1 stats in OOM logs
- Yosry has also eliminated cgroup's atomic rstat flushing
- Nhat Pham adds the new cachestat() syscall. It provides userspace
with the ability to query pagecache status - a similar concept to
mincore() but more powerful and with improved usability
- Mel Gorman provides more optimizations for compaction, reducing the
prevalence of page rescanning
- Lorenzo Stoakes has done some maintanance work on the
get_user_pages() interface
- Liam Howlett continues with cleanups and maintenance work to the
maple tree code. Peng Zhang also does some work on maple tree
- Johannes Weiner has done some cleanup work on the compaction code
- David Hildenbrand has contributed additional selftests for
get_user_pages()
- Thomas Gleixner has contributed some maintenance and optimization
work for the vmalloc code
- Baolin Wang has provided some compaction cleanups,
- SeongJae Park continues maintenance work on the DAMON code
- Huang Ying has done some maintenance on the swap code's usage of
device refcounting
- Christoph Hellwig has some cleanups for the filemap/directio code
- Ryan Roberts provides two patch series which yield some
rationalization of the kernel's access to pte entries - use the
provided APIs rather than open-coding accesses
- Lorenzo Stoakes has some fixes to the interaction between pagecache
and directio access to file mappings
- John Hubbard has a series of fixes to the MM selftesting code
- ZhangPeng continues the folio conversion campaign
- Hugh Dickins has been working on the pagetable handling code, mainly
with a view to reducing the load on the mmap_lock
- Catalin Marinas has reduced the arm64 kmalloc() minimum alignment
from 128 to 8
- Domenico Cerasuolo has improved the zswap reclaim mechanism by
reorganizing the LRU management
- Matthew Wilcox provides some fixups to make gfs2 work better with the
buffer_head code
- Vishal Moola also has done some folio conversion work
- Matthew Wilcox has removed the remnants of the pagevec code - their
functionality is migrated over to struct folio_batch
* tag 'mm-stable-2023-06-24-19-15' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (380 commits)
mm/hugetlb: remove hugetlb_set_page_subpool()
mm: nommu: correct the range of mmap_sem_read_lock in task_mem()
hugetlb: revert use of page_cache_next_miss()
Revert "page cache: fix page_cache_next/prev_miss off by one"
mm/vmscan: fix root proactive reclaim unthrottling unbalanced node
mm: memcg: rename and document global_reclaim()
mm: kill [add|del]_page_to_lru_list()
mm: compaction: convert to use a folio in isolate_migratepages_block()
mm: zswap: fix double invalidate with exclusive loads
mm: remove unnecessary pagevec includes
mm: remove references to pagevec
mm: rename invalidate_mapping_pagevec to mapping_try_invalidate
mm: remove struct pagevec
net: convert sunrpc from pagevec to folio_batch
i915: convert i915_gpu_error to use a folio_batch
pagevec: rename fbatch_count()
mm: remove check_move_unevictable_pages()
drm: convert drm_gem_put_pages() to use a folio_batch
i915: convert shmem_sg_free_table() to use a folio_batch
scatterlist: add sg_set_folio()
...
-----BEGIN PGP SIGNATURE-----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=zP4Y
-----END PGP SIGNATURE-----
Merge tag 'for-6.5/block-2023-06-23' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe pull request via Keith:
- Various cleanups all around (Irvin, Chaitanya, Christophe)
- Better struct packing (Christophe JAILLET)
- Reduce controller error logs for optional commands (Keith)
- Support for >=64KiB block sizes (Daniel Gomez)
- Fabrics fixes and code organization (Max, Chaitanya, Daniel
Wagner)
- bcache updates via Coly:
- Fix a race at init time (Mingzhe Zou)
- Misc fixes and cleanups (Andrea, Thomas, Zheng, Ye)
- use page pinning in the block layer for dio (David)
- convert old block dio code to page pinning (David, Christoph)
- cleanups for pktcdvd (Andy)
- cleanups for rnbd (Guoqing)
- use the unchecked __bio_add_page() for the initial single page
additions (Johannes)
- fix overflows in the Amiga partition handling code (Michael)
- improve mq-deadline zoned device support (Bart)
- keep passthrough requests out of the IO schedulers (Christoph, Ming)
- improve support for flush requests, making them less special to deal
with (Christoph)
- add bdev holder ops and shutdown methods (Christoph)
- fix the name_to_dev_t() situation and use cases (Christoph)
- decouple the block open flags from fmode_t (Christoph)
- ublk updates and cleanups, including adding user copy support (Ming)
- BFQ sanity checking (Bart)
- convert brd from radix to xarray (Pankaj)
- constify various structures (Thomas, Ivan)
- more fine grained persistent reservation ioctl capability checks
(Jingbo)
- misc fixes and cleanups (Arnd, Azeem, Demi, Ed, Hengqi, Hou, Jan,
Jordy, Li, Min, Yu, Zhong, Waiman)
* tag 'for-6.5/block-2023-06-23' of git://git.kernel.dk/linux: (266 commits)
scsi/sg: don't grab scsi host module reference
ext4: Fix warning in blkdev_put()
block: don't return -EINVAL for not found names in devt_from_devname
cdrom: Fix spectre-v1 gadget
block: Improve kernel-doc headers
blk-mq: don't insert passthrough request into sw queue
bsg: make bsg_class a static const structure
ublk: make ublk_chr_class a static const structure
aoe: make aoe_class a static const structure
block/rnbd: make all 'class' structures const
block: fix the exclusive open mask in disk_scan_partitions
block: add overflow checks for Amiga partition support
block: change all __u32 annotations to __be32 in affs_hardblocks.h
block: fix signed int overflow in Amiga partition support
block: add capacity validation in bdev_add_partition()
block: fine-granular CAP_SYS_ADMIN for Persistent Reservation
block: disallow Persistent Reservation on partitions
reiserfs: fix blkdev_put() warning from release_journal_dev()
block: fix wrong mode for blkdev_get_by_dev() from disk_scan_partitions()
block: document the holder argument to blkdev_get_by_path
...
Use sendmsg() conditionally with MSG_SPLICE_PAGES in _drbd_send_page()
rather than calling sendpage() or _drbd_no_send_page().
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Philipp Reisner <philipp.reisner@linbit.com>
cc: Lars Ellenberg <lars.ellenberg@linbit.com>
cc: "Christoph Böhmwalder" <christoph.boehmwalder@linbit.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: drbd-dev@lists.linbit.com
Link: https://lore.kernel.org/r/20230623225513.2732256-11-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that the driver core allows for struct class to be in read-only
memory, move the ublk_chr_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230620180129.645646-7-gregkh@linuxfoundation.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that the driver core allows for struct class to be in read-only
memory, move the aoe_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Justin Sanders <justin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230620180129.645646-6-gregkh@linuxfoundation.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that the driver core allows for struct class to be in read-only
memory, making all 'class' structures to be declared at build time
placing them into read-only memory, instead of having to be dynamically
allocated at load time.
Cc: "Md. Haris Iqbal" <haris.iqbal@ionos.com>
Cc: Jack Wang <jinpu.wang@ionos.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20230620180129.645646-5-gregkh@linuxfoundation.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This reverts commit 07b679f70d.
This change appears to have broken things...
We now see applications hanging during disk accesses.
e.g.
multi-port virtio-blk device running in h/w (FPGA)
Host running a simple 'fio' test.
[global]
thread=1
direct=1
ioengine=libaio
norandommap=1
group_reporting=1
bs=4K
rw=read
iodepth=128
runtime=1
numjobs=4
time_based
[job0]
filename=/dev/vda
[job1]
filename=/dev/vdb
[job2]
filename=/dev/vdc
...
[job15]
filename=/dev/vdp
i.e. 16 disks; 4 queues per disk; simple burst of 4KB reads
This is repeatedly run in a loop.
After a few, normally <10 seconds, fio hangs.
With 64 queues (16 disks), failure occurs within a few seconds; with 8 queues (2 disks) it may take ~hour before hanging.
Last message:
fio-3.19
Starting 8 threads
Jobs: 1 (f=1): [_(7),R(1)][68.3%][eta 03h:11m:06s]
I think this means at the end of the run 1 queue was left incomplete.
'diskstats' (run while fio is hung) shows no outstanding transactions.
e.g.
$ cat /proc/diskstats
...
252 0 vda 1843140071 0 14745120568 712568645 0 0 0 0 0 3117947 712568645 0 0 0 0 0 0
252 16 vdb 1816291511 0 14530332088 704905623 0 0 0 0 0 3117711 704905623 0 0 0 0 0 0
...
Other stats (in the h/w, and added to the virtio-blk driver ([a]virtio_queue_rq(), [b]virtblk_handle_req(), [c]virtblk_request_done()) all agree, and show every request had a completion, and that virtblk_request_done() never gets called.
e.g.
PF= 0 vq=0 1 2 3
[a]request_count - 839416590 813148916 105586179 84988123
[b]completion1_count - 839416590 813148916 105586179 84988123
[c]completion2_count - 0 0 0 0
PF= 1 vq=0 1 2 3
[a]request_count - 823335887 812516140 104582672 75856549
[b]completion1_count - 823335887 812516140 104582672 75856549
[c]completion2_count - 0 0 0 0
i.e. the issue is after the virtio-blk driver.
This change was introduced in kernel 6.3.0.
I am seeing this using 6.3.3.
If I run with an earlier kernel (5.15), it does not occur.
If I make a simple patch to the 6.3.3 virtio-blk driver, to skip the blk_mq_add_to_batch()call, it does not fail.
e.g.
kernel 5.15 - this is OK
virtio_blk.c,virtblk_done() [irq handler]
if (likely(!blk_should_fake_timeout(req->q))) {
blk_mq_complete_request(req);
}
kernel 6.3.3 - this fails
virtio_blk.c,virtblk_handle_req() [irq handler]
if (likely(!blk_should_fake_timeout(req->q))) {
if (!blk_mq_complete_request_remote(req)) {
if (!blk_mq_add_to_batch(req, iob, virtblk_vbr_status(vbr), virtblk_complete_batch)) {
virtblk_request_done(req); //this never gets called... so blk_mq_add_to_batch() must always succeed
}
}
}
If I do, kernel 6.3.3 - this is OK
virtio_blk.c,virtblk_handle_req() [irq handler]
if (likely(!blk_should_fake_timeout(req->q))) {
if (!blk_mq_complete_request_remote(req)) {
virtblk_request_done(req); //force this here...
if (!blk_mq_add_to_batch(req, iob, virtblk_vbr_status(vbr), virtblk_complete_batch)) {
virtblk_request_done(req); //this never gets called... so blk_mq_add_to_batch() must always succeed
}
}
}
Perhaps you might like to fix/test/revert this change...
Martin
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306090826.C1fZmdMe-lkp@intel.com/
Cc: Suwan Kim <suwan.kim027@gmail.com>
Tested-by: edliaw@google.com
Reported-by: "Roberts, Martin" <martin.roberts@intel.com>
Message-Id: <336455b4f630f329380a8f53ee8cad3868764d5c.1686295549.git.mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix a missing conversion to the new BLK_OPEN constant in swim.
Fixes: 05bdb99653 ("block: replace fmode_t with a block-specific type for block open flags")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230620043051.707196-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Recompression threshold should be below huge-size-class watermark. Any
object larger than huge-size-class is a "huge object" and occupies a
whole physical page on the zsmalloc side, in other words it's
incompressible, as far as zsmalloc is concerned.
Link: https://lkml.kernel.org/r/20230614141338.3480029-1-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Suggested-by: Brian Geffon <bgeffon@google.com>
Acked-by: Brian Geffon <bgeffon@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The body of the loop is run without RCU lock held. Use the regular
cond_resched() instead of cond_resched_rcu().
Fixes: 786bb02458 ("brd: use XArray instead of radix-tree to index backing pages")
Suggested-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20230614133538.1279369-1-p.raghav@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The only overlap between the block open flags mapped into the fmode_t and
other uses of fmode_t are FMODE_READ and FMODE_WRITE. Define a new
blk_mode_t instead for use in blkdev_get_by_{dev,path}, ->open and
->ioctl and stop abusing fmode_t.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jack Wang <jinpu.wang@ionos.com> [rnbd]
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Link: https://lore.kernel.org/r/20230608110258.189493-28-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stop passing the fmode_t around and just use a simple bool to track if
an export is read-only.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20230608110258.189493-24-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The current interface for exclusive opens is rather confusing as it
requires both the FMODE_EXCL flag and a holder. Remove the need to pass
FMODE_EXCL and just key off the exclusive open off a non-NULL holder.
For blkdev_put this requires adding the holder argument, which provides
better debug checking that only the holder actually releases the hold,
but at the same time allows removing the now superfluous mode argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Acked-by: David Sterba <dsterba@suse.com> [btrfs]
Acked-by: Jack Wang <jinpu.wang@ionos.com> [rnbd]
Link: https://lore.kernel.org/r/20230608110258.189493-16-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Passing a holder to blkdev_get_by_path when FMODE_EXCL isn't set doesn't
make sense, so pass NULL instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20230608110258.189493-14-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The mode argument to the ->release block_device_operation is never used,
so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Acked-by: Jack Wang <jinpu.wang@ionos.com> [rnbd]
Link: https://lore.kernel.org/r/20230608110258.189493-10-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
->open is only called on the whole device. Make that explicit by
passing a gendisk instead of the block_device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Acked-by: Jack Wang <jinpu.wang@ionos.com> [rnbd]
Link: https://lore.kernel.org/r/20230608110258.189493-9-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bdev_check_media_change should only ever be called for the whole device.
Pass a gendisk to make that explicit and rename the function to
disk_check_media_change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Link: https://lore.kernel.org/r/20230608110258.189493-8-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Let's always set errno after pr_err which is consistent with
default case.
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Link: https://lore.kernel.org/r/20230524070026.2932-7-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Check ret is enough since if sess_dev is NULL which also
implies ret should be 0.
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Link: https://lore.kernel.org/r/20230524070026.2932-5-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add one new array (marked with __maybe_unused to prevent gcc warning about
"defined but not used" with W=1), then we can remove rnbd_access_mode_str
and rnbd-common.c accordingly.
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20230524070026.2932-4-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No need to include it since none of macros in limits.h are
used by rnbd-srv.
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Link: https://lore.kernel.org/r/20230524070026.2932-3-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This routine is not called since added. Then the two flags
(RNBD_OP_LAST and RNBD_F_ALL) can be removed too after kill
rnbd_flags_supported.
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Link: https://lore.kernel.org/r/20230524070026.2932-2-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=fNEf
-----END PGP SIGNATURE-----
Merge tag 'block-6.4-2023-06-09' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- Fix an issue with the hardware queue nr_active, causing it to become
imbalanced (Tian)
- Fix an issue with null_blk not releasing pages if configured as
memory backed (Nitesh)
- Fix a locking issue in dasd (Jan)
* tag 'block-6.4-2023-06-09' of git://git.kernel.dk/linux:
s390/dasd: Use correct lock while counting channel queue length
null_blk: Fix: memory release when memory_backed=1
blk-mq: fix blk_mq_hw_ctx active request accounting
Sort the headers in alphabetic order in order to ease
the maintenance for this part.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230310164549.22133-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In the snippets like the following
if (...)
return / goto / break / continue ...;
else
...
the 'else' is redundant. Get rid of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230310164549.22133-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use DEFINE_SHOW_ATTRIBUTE() helper macro to simplify the code.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230310164549.22133-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since the commit 72deb455b5 ("block: remove CONFIG_LBDAF")
the sector_t is always 64-bit type, no need to cast anymore.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230310164549.22133-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The code can be neater without forward declarations.
Get rid of pkt_seq_show() forward declaration. This
will also allow futher cleanups to be cleaner.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230310164549.22133-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230310164549.22133-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We may use traditional dev_*() macros instead of custom ones
provided by the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230310164549.22133-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the index allocated by idr_alloc greater than MINORMASK >> part_shift,
the device number will overflow, resulting in failure to create a block
device.
Fix it by imiting the size of the max allocation.
Signed-off-by: Zhong Jinghua <zhongjinghua@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230605122159.2134384-1-zhongjinghua@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move capturing the snapshot context into the image request state
machine, after exclusive lock is ensured to be held for the duration of
dealing with the image request. This is needed to ensure correctness
of fast-diff states (OBJECT_EXISTS vs OBJECT_EXISTS_CLEAN) and object
deltas computed based off of them. Otherwise the object map that is
forked for the snapshot isn't guaranteed to accurately reflect the
contents of the snapshot when the snapshot is taken under I/O. This
breaks differential backup and snapshot-based mirroring use cases with
fast-diff enabled: since some object deltas may be incomplete, the
destination image may get corrupted.
Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/61472
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
Move RBD_OBJ_FLAG_COPYUP_ENABLED flag setting into the object request
state machine to allow for the snapshot context to be captured in the
image request state machine rather than in rbd_queue_workfn().
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
Add a new blk_holder_ops structure, which is passed to blkdev_get_by_* and
installed in the block_device for exclusive claims. It will be used to
allow the block layer to call back into the user of the block device for
thing like notification of a removed device or a device resize.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Link: https://lore.kernel.org/r/20230601094459.1350643-10-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
__KERNEL_SYSCALLS__ hasn't been needed since Linux 2.6.19 so stop
defining it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20230601151646.1386867-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add control command of UBLK_U_CMD_GET_FEATURES for returning driver's
feature set or capability.
This way can simplify userspace for maintaining compatibility because
userspace doesn't need to send command to one device for querying driver
feature set any more. Such as, with the queried feature set, userspace
can choose to use:
- UBLK_CMD_GET_DEV_INFO2 or UBLK_CMD_GET_DEV_INFO,
- UBLK_U_CMD_* or UBLK_CMD_*
Userspace code:
https://github.com/ming1/ubdsrv/commits/features-cmd
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230603040601.775227-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The floppy code uses bio_add_page() to add a page to a newly created bio.
bio_add_page() can fail, but the return value is never checked.
Use __bio_add_page() as adding a single page to a newly created bio is
guaranteed to succeed.
This brings us a step closer to marking bio_add_page() as __must_check.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/33c445a3b431270c72d9be03d5da1b08ae983920.1685532726.git.johannes.thumshirn@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The zram writeback code uses bio_add_page() to add a page to a newly
created bio. bio_add_page() can fail, but the return value is never
checked.
Use __bio_add_page() as adding a single page to a newly created bio is
guaranteed to succeed.
This brings us a step closer to marking bio_add_page() as __must_check.
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/cfd141dd7773315879a126f2aa81b7f698bc0e10.1685532726.git.johannes.thumshirn@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The drbd code only adds a single page to a newly created bio. So use
__bio_add_page() to add the page which is guaranteed to succeed in this
case.
This brings us closer to marking bio_add_page() as __must_check.
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/435007afac14f3766455559059d21843771fae53.1685532726.git.johannes.thumshirn@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCZHGVRAAKCRCAXGG7T9hj
vqtJAQDizKasLE7tSnfs/FrZ/4xPaDLe3bQifMx2C1dtYCjRcAD/ciZSa1L0WzZP
dpEZnlYRzsR3bwLktQEMQFOvlbh1SwE=
=K860
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.4-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- a double free fix in the Xen pvcalls backend driver
- a fix for a regression causing the MSI related sysfs entries to not
being created in Xen PV guests
- a fix in the Xen blkfront driver for handling insane input data
better
* tag 'for-linus-6.4-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/pci/xen: populate MSI sysfs entries
xen/pvcalls-back: fix double frees with pvcalls_new_active_socket()
xen/blkfront: Only check REQ_FUA for writes
The existing code silently converts read operations with the
REQ_FUA bit set into write-barrier operations. This results in data
loss as the backend scribbles zeroes over the data instead of returning
it.
While the REQ_FUA bit doesn't make sense on a read operation, at least
one well-known out-of-tree kernel module does set it and since it
results in data loss, let's be safe here and only look at REQ_FUA for
writes.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20230426164005.2213139-1-ross.lagerwall@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Return type of iov_iter_get_pages2() is ssize_t instead of size_t, so
fix it.
Fixes: 981f95a571 ("ublk: cleanup ublk_copy_user_pages")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230520151134.459679-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently copy between io request buffer(pages) and userspace buffer is
done inside ublk_map_io() or ublk_unmap_io(). This way performs very
well in case of pre-allocated userspace io buffer.
For dynamically allocated or external userspace backend io buffer,
UBLK_F_NEED_GET_DATA is added for ublk server to provide buffer by one
extra command communication for WRITE request. For READ, userspace
simply provides buffer, but can't know when the buffer is done[1].
Add UBLK_F_USER_COPY by moving io data copy out of kernel by providing
read()/write() on /dev/ublkcN, and simply let ublk server do the io
data copy. This way makes both side cleaner, the cost is that one extra
syscall for copy io data between request and backend buffer.
With UBLK_F_USER_COPY, it actually becomes possible to run per-io zero
copy now, such as, only do zero copy for big size IO, so it can be
thought as one prep patch for supporting zero copy. Meantime zero copy
still needs to expose read()/write() buffer for some corner case, such
as passthrough IO.
[1] READ buffer in UBLK_F_NEED_GET_DATA
https://lore.kernel.org/linux-block/116d8a56-0881-56d3-9bcc-78ff3e1dc4e5@linux.alibaba.com/T/#m23bd4b8634c0a054e6797063167b469949a247bb
ublksrv loop usercopy code:
https://github.com/ming1/ubdsrv/commits/usercopy
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230519065030.351216-8-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Support pread()/pwrite() on ublk char device for reading/writing request
io buffer, so data copy between io request buffer and userspace buffer
can be moved to ublk server from ublk driver. Then UBLK_F_NEED_GET_DATA
becomes not necessary, so ublk server can allocate buffer without one
extra round uring command communication for userspace to provide buffer.
IO buffer can be located by iocb->ki_pos which encodes buffer offset, io
tag and queue id info, and type of iocb->ki_pos is u64, so it is big
enough for holding reasonable queue depth, nr_queues and max io buffer
size.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230519065030.351216-7-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add 'offset' to 'struct ublk_map_data', so that ublk_copy_user_pages()
can be used to copy any sub-buffer(linear mapped) of the request.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230519065030.351216-6-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add one reference counter into request pdu data, and hold this reference
in the request's lifetime.
Prepare for supporting to move request data copy into userspace, which
needs to copy request data by read()/write() on /dev/ublkcN, so we have
to guarantee that read()/write() is done on one valid/active request,
and that will be enhanced by holding the io request reference in
read()/write().
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230519065030.351216-5-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Clean up ublk_copy_user_pages() by using iov_iter_get_pages2, and code
gets simplified a lot and becomes much more readable than before.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230519065030.351216-4-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
task_work_add() is used from early ublk development stage for handling
request in batch. However, since commit 7d4a93176e ("ublk_drv: don't
forward io commands in reserve order"), we can get similar batch
processing with io_uring_cmd_complete_in_task(), and similar performance
data is observed between task_work_add() and
io_uring_cmd_complete_in_task().
Meantime we can kill one fast code path, which is actually seldom used
given it is common to build ublk driver as module.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230519065030.351216-2-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When handling UBLK_IO_FETCH_REQ, ctx->uring_lock is grabbed first, then
ub->mutex is acquired.
When handling UBLK_CMD_STOP_DEV or UBLK_CMD_DEL_DEV, ub->mutex is
grabbed first, then calling io_uring_cmd_done() for canceling uring
command, in which ctx->uring_lock may be required.
Real deadlock only happens when all the above commands are issued from
same uring context, and in reality different uring contexts are often used
for handing control command and IO command.
Fix the issue by using io_uring_cmd_complete_in_task() to cancel command
in ublk_cancel_dev(ublk_cancel_queue).
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Closes: https://lore.kernel.org/linux-block/becol2g7sawl4rsjq2dztsbc7mqypfqko6wzsyoyazqydoasml@rcxarzwidrhk
Cc: Ziyang Zhang <ZiyangZhang@linux.alibaba.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20230517133408.210944-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
XArray was introduced to hold large array of pointers with a simple API.
XArray API also provides array semantics which simplifies the way we store
and access the backing pages, and the code becomes significantly easier
to understand.
No performance difference was noticed between the two implementation
using fio with direct=1 [1].
[1] Performance in KIOPS:
| radix-tree | XArray | Diff
| | |
write | 315 | 313 | -0.6%
randwrite | 286 | 290 | +1.3%
read | 330 | 335 | +1.5%
randread | 309 | 312 | +0.9%
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20230511121544.111648-1-p.raghav@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In case of CONFIG_BLKDEV_UBLK_LEGACY_OPCODES, type of cmd opcode could
be 0 or 'u'; and type can only be 'u' if CONFIG_BLKDEV_UBLK_LEGACY_OPCODES
isn't set.
So fix the wrong check.
Fixes: 2d786e66c9 ("block: ublk: switch to ioctl command encoding")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230505153142.1258336-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The debugfs_create_dir function returns ERR_PTR in case of error, and the
only correct way to check if an error occurred is 'IS_ERR' inline function.
This patch will replace the null-comparison with IS_ERR.
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Link: https://lore.kernel.org/r/20230512130533.98709-1-ivan.orlov0322@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=l7Mo
-----END PGP SIGNATURE-----
Merge tag 'for-6.4/io_uring-2023-05-07' of git://git.kernel.dk/linux
Pull more io_uring updates from Jens Axboe:
"Nothing major in here, just two different parts:
- A small series from Breno that enables passing the full SQE down
for ->uring_cmd().
This is a prerequisite for enabling full network socket operations.
Queued up a bit late because of some stylistic concerns that got
resolved, would be nice to have this in 6.4-rc1 so the dependent
work will be easier to handle for 6.5.
- Fix for the huge page coalescing, which was a regression introduced
in the 6.3 kernel release (Tobias)"
* tag 'for-6.4/io_uring-2023-05-07' of git://git.kernel.dk/linux:
io_uring: Remove unnecessary BUILD_BUG_ON
io_uring: Pass whole sqe to commands
io_uring: Create a helper to return the SQE size
io_uring/rsrc: check for nonconsecutive pages
-----BEGIN PGP SIGNATURE-----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=gAYf
-----END PGP SIGNATURE-----
Merge tag 'for-6.4/block-2023-05-06' of git://git.kernel.dk/linux
Pull more block updates from Jens Axboe:
- MD pull request via Song:
- Improve raid5 sequential IO performance on spinning disks, which
fixes a regression since v6.0 (Jan Kara)
- Fix bitmap offset types, which fixes an issue introduced in this
merge window (Jonathan Derrick)
- Cleanup of hweight type used for cgroup writeback (Maxim)
- Fix a regression with the "has_submit_bio" changes across partitions
(Ming)
- Cleanup of QUEUE_FLAG_ADD_RANDOM clearing.
We used to set this flag on queues non blk-mq queues, and hence some
drivers clear it unconditionally. Since all of these have since been
converted to true blk-mq drivers, drop the useless clear as the bit
is not set (Chaitanya)
- Fix the flags being set in a bio for a flush for drbd (Christoph)
- Cleanup and deduplication of the code handling setting block device
capacity (Damien)
- Fix for ublk handling IO timeouts (Ming)
- Fix for a regression in blk-cgroup teardown (Tao)
- NBD documentation and code fixes (Eric)
- Convert blk-integrity to using device_attributes rather than a second
kobject to manage lifetimes (Thomas)
* tag 'for-6.4/block-2023-05-06' of git://git.kernel.dk/linux:
ublk: add timeout handler
drbd: correctly submit flush bio on barrier
mailmap: add mailmap entries for Jens Axboe
block: Skip destroyed blkg when restart in blkg_destroy_all()
writeback: fix call of incorrect macro
md: Fix bitmap offset type in sb writer
md/raid5: Improve performance for sequential IO
docs nbd: userspace NBD now favors github over sourceforge
block nbd: use req.cookie instead of req.handle
uapi nbd: add cookie alias to handle
uapi nbd: improve doc links to userspace spec
blk-integrity: register sysfs attributes on struct device
blk-integrity: convert to struct device_attribute
blk-integrity: use sysfs_emit
block/drivers: remove dead clear of random flag
block: sync part's ->bd_has_submit_bio with disk's
block: Cleanup set_capacity()/bdev_set_nr_sectors()
Currently uring CMD operation relies on having large SQEs, but future
operations might want to use normal SQE.
The io_uring_cmd currently only saves the payload (cmd) part of the SQE,
but, for commands that use normal SQE size, it might be necessary to
access the initial SQE fields outside of the payload/cmd block. So,
saves the whole SQE other than just the pdu.
This changes slightly how the io_uring_cmd works, since the cmd
structures and callbacks are not opaque to io_uring anymore. I.e, the
callbacks can look at the SQE entries, not only, in the cmd structure.
The main advantage is that we don't need to create custom structures for
simple commands.
Creates io_uring_sqe_cmd() that returns the cmd private data as a null
pointer and avoids casting in the callee side.
Also, make most of ublk_drv's sqe->cmd priv structure into const, and use
io_uring_sqe_cmd() to get the private structure, removing the unwanted
cast. (There is one case where the cast is still needed since the
header->{len,addr} is updated in the private structure)
Suggested-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/20230504121856.904491-3-leitao@debian.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add timeout handler, so that we can provide forward progress guarantee for
unprivileged ublk, which can't be trusted.
One thing is that sync() calls sync_bdevs(wait) for all block devices after
running sync_bdevs(no_wait), and if one device can't move on, the sync() won't
return any more.
Add timeout for unprivileged ublk to avoid such affect for other users which call
sync() syscall.
Meantime clear UBLK_F_USER_RECOVERY_REISSUE for unprivileged ublk since
that feature may cause IO hang too.
Fixes: 4093cb5a06 ("ublk_drv: add mechanism for supporting unprivileged ublk device")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230502024231.888498-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When we receive a flush command (or "barrier" in DRBD), we currently use
a REQ_OP_FLUSH with the REQ_PREFLUSH flag set.
The correct way to submit a flush bio is by using a REQ_OP_WRITE without
any data, and set the REQ_PREFLUSH flag.
Since commit b4a6bb3a67 ("block: add a sanity check for non-write
flush/fua bios"), this triggers a warning in the block layer, but this
has been broken for quite some time before that.
So use the correct set of flags to actually make the flush happen.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: stable@vger.kernel.org
Fixes: f9ff0da564 ("drbd: allow parallel flushes for multi-volume resources")
Reported-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230503121937.17232-1-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
switching from a user process to a kernel thread.
- More folio conversions from Kefeng Wang, Zhang Peng and Pankaj Raghav.
- zsmalloc performance improvements from Sergey Senozhatsky.
- Yue Zhao has found and fixed some data race issues around the
alteration of memcg userspace tunables.
- VFS rationalizations from Christoph Hellwig:
- removal of most of the callers of write_one_page().
- make __filemap_get_folio()'s return value more useful
- Luis Chamberlain has changed tmpfs so it no longer requires swap
backing. Use `mount -o noswap'.
- Qi Zheng has made the slab shrinkers operate locklessly, providing
some scalability benefits.
- Keith Busch has improved dmapool's performance, making part of its
operations O(1) rather than O(n).
- Peter Xu adds the UFFD_FEATURE_WP_UNPOPULATED feature to userfaultd,
permitting userspace to wr-protect anon memory unpopulated ptes.
- Kirill Shutemov has changed MAX_ORDER's meaning to be inclusive rather
than exclusive, and has fixed a bunch of errors which were caused by its
unintuitive meaning.
- Axel Rasmussen give userfaultfd the UFFDIO_CONTINUE_MODE_WP feature,
which causes minor faults to install a write-protected pte.
- Vlastimil Babka has done some maintenance work on vma_merge():
cleanups to the kernel code and improvements to our userspace test
harness.
- Cleanups to do_fault_around() by Lorenzo Stoakes.
- Mike Rapoport has moved a lot of initialization code out of various
mm/ files and into mm/mm_init.c.
- Lorenzo Stoakes removd vmf_insert_mixed_prot(), which was added for
DRM, but DRM doesn't use it any more.
- Lorenzo has also coverted read_kcore() and vread() to use iterators
and has thereby removed the use of bounce buffers in some cases.
- Lorenzo has also contributed further cleanups of vma_merge().
- Chaitanya Prakash provides some fixes to the mmap selftesting code.
- Matthew Wilcox changes xfs and afs so they no longer take sleeping
locks in ->map_page(), a step towards RCUification of pagefaults.
- Suren Baghdasaryan has improved mmap_lock scalability by switching to
per-VMA locking.
- Frederic Weisbecker has reworked the percpu cache draining so that it
no longer causes latency glitches on cpu isolated workloads.
- Mike Rapoport cleans up and corrects the ARCH_FORCE_MAX_ORDER Kconfig
logic.
- Liu Shixin has changed zswap's initialization so we no longer waste a
chunk of memory if zswap is not being used.
- Yosry Ahmed has improved the performance of memcg statistics flushing.
- David Stevens has fixed several issues involving khugepaged,
userfaultfd and shmem.
- Christoph Hellwig has provided some cleanup work to zram's IO-related
code paths.
- David Hildenbrand has fixed up some issues in the selftest code's
testing of our pte state changing.
- Pankaj Raghav has made page_endio() unneeded and has removed it.
- Peter Xu contributed some rationalizations of the userfaultfd
selftests.
- Yosry Ahmed has fixed an issue around memcg's page recalim accounting.
- Chaitanya Prakash has fixed some arm-related issues in the
selftests/mm code.
- Longlong Xia has improved the way in which KSM handles hwpoisoned
pages.
- Peter Xu fixes a few issues with uffd-wp at fork() time.
- Stefan Roesch has changed KSM so that it may now be used on a
per-process and per-cgroup basis.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZEr3zQAKCRDdBJ7gKXxA
jlLoAP0fpQBipwFxED0Us4SKQfupV6z4caXNJGPeay7Aj11/kQD/aMRC2uPfgr96
eMG3kwn2pqkB9ST2QpkaRbxA//eMbQY=
=J+Dj
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2023-04-27-15-30' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- Nick Piggin's "shoot lazy tlbs" series, to improve the peformance of
switching from a user process to a kernel thread.
- More folio conversions from Kefeng Wang, Zhang Peng and Pankaj
Raghav.
- zsmalloc performance improvements from Sergey Senozhatsky.
- Yue Zhao has found and fixed some data race issues around the
alteration of memcg userspace tunables.
- VFS rationalizations from Christoph Hellwig:
- removal of most of the callers of write_one_page()
- make __filemap_get_folio()'s return value more useful
- Luis Chamberlain has changed tmpfs so it no longer requires swap
backing. Use `mount -o noswap'.
- Qi Zheng has made the slab shrinkers operate locklessly, providing
some scalability benefits.
- Keith Busch has improved dmapool's performance, making part of its
operations O(1) rather than O(n).
- Peter Xu adds the UFFD_FEATURE_WP_UNPOPULATED feature to userfaultd,
permitting userspace to wr-protect anon memory unpopulated ptes.
- Kirill Shutemov has changed MAX_ORDER's meaning to be inclusive
rather than exclusive, and has fixed a bunch of errors which were
caused by its unintuitive meaning.
- Axel Rasmussen give userfaultfd the UFFDIO_CONTINUE_MODE_WP feature,
which causes minor faults to install a write-protected pte.
- Vlastimil Babka has done some maintenance work on vma_merge():
cleanups to the kernel code and improvements to our userspace test
harness.
- Cleanups to do_fault_around() by Lorenzo Stoakes.
- Mike Rapoport has moved a lot of initialization code out of various
mm/ files and into mm/mm_init.c.
- Lorenzo Stoakes removd vmf_insert_mixed_prot(), which was added for
DRM, but DRM doesn't use it any more.
- Lorenzo has also coverted read_kcore() and vread() to use iterators
and has thereby removed the use of bounce buffers in some cases.
- Lorenzo has also contributed further cleanups of vma_merge().
- Chaitanya Prakash provides some fixes to the mmap selftesting code.
- Matthew Wilcox changes xfs and afs so they no longer take sleeping
locks in ->map_page(), a step towards RCUification of pagefaults.
- Suren Baghdasaryan has improved mmap_lock scalability by switching to
per-VMA locking.
- Frederic Weisbecker has reworked the percpu cache draining so that it
no longer causes latency glitches on cpu isolated workloads.
- Mike Rapoport cleans up and corrects the ARCH_FORCE_MAX_ORDER Kconfig
logic.
- Liu Shixin has changed zswap's initialization so we no longer waste a
chunk of memory if zswap is not being used.
- Yosry Ahmed has improved the performance of memcg statistics
flushing.
- David Stevens has fixed several issues involving khugepaged,
userfaultfd and shmem.
- Christoph Hellwig has provided some cleanup work to zram's IO-related
code paths.
- David Hildenbrand has fixed up some issues in the selftest code's
testing of our pte state changing.
- Pankaj Raghav has made page_endio() unneeded and has removed it.
- Peter Xu contributed some rationalizations of the userfaultfd
selftests.
- Yosry Ahmed has fixed an issue around memcg's page recalim
accounting.
- Chaitanya Prakash has fixed some arm-related issues in the
selftests/mm code.
- Longlong Xia has improved the way in which KSM handles hwpoisoned
pages.
- Peter Xu fixes a few issues with uffd-wp at fork() time.
- Stefan Roesch has changed KSM so that it may now be used on a
per-process and per-cgroup basis.
* tag 'mm-stable-2023-04-27-15-30' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (369 commits)
mm,unmap: avoid flushing TLB in batch if PTE is inaccessible
shmem: restrict noswap option to initial user namespace
mm/khugepaged: fix conflicting mods to collapse_file()
sparse: remove unnecessary 0 values from rc
mm: move 'mmap_min_addr' logic from callers into vm_unmapped_area()
hugetlb: pte_alloc_huge() to replace huge pte_alloc_map()
maple_tree: fix allocation in mas_sparse_area()
mm: do not increment pgfault stats when page fault handler retries
zsmalloc: allow only one active pool compaction context
selftests/mm: add new selftests for KSM
mm: add new KSM process and sysfs knobs
mm: add new api to enable ksm per process
mm: shrinkers: fix debugfs file permissions
mm: don't check VMA write permissions if the PTE/PMD indicates write permissions
migrate_pages_batch: fix statistics for longterm pin retry
userfaultfd: use helper function range_in_vma()
lib/show_mem.c: use for_each_populated_zone() simplify code
mm: correct arg in reclaim_pages()/reclaim_clean_pages_from_list()
fs/buffer: convert create_page_buffers to folio_create_buffers
fs/buffer: add folio_create_empty_buffers helper
...
The NBD spec was recently changed [1] to refer to the opaque client
identifier as a 'cookie' rather than a 'handle', but has for a much
longer time listed it as a 64-bit value, and declares that all values
in the NBD protocol are sent in network byte order (big-endian).
Because the value is opaque to the server, it doesn't usually matter
what endianness we send as the client - as long as we are consistent
that either we byte-swap on both write and read, or on neither, then
we can match server replies back to our requests. That said, our
internal use of the cookie is as a 64-bit number (well, as two 32-bit
numbers concatenated together), rather than as 8 individual bytes; so
prior to this commit, we ARE leaking the native endianness of our
internals as a client out to the server. We don't know of any server
that will actually inspect the opaque value and behave differently
depending on whether a little-endian or big-endian client is sending
requests, but since we DO log the cookie value, a wireshark capture of
the network traffic is easier to correlate back to the kernel traffic
of a big-endian host (where the u64 and char[8] representations are
the same) than of a little-endian host (where if wireshark honors the
NBD spec and displays a u64 in network byte order, it is byte-swapped
from what the kernel logged).
The fix in this patch is thus two-part: it now consistently uses
network byte order for the opaque value (no difference to a big-endian
machine, but an extra byteswap on a little-endian machine; probably in
the noise compared to the overhead of network traffic in general), and
now uses a 64-bit integer instead of char[8] as its preferred access
to the opaque value (direct assignment instead of memcpy()).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20230410180611.1051618-4-eblake@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCZEolJQAKCRCAXGG7T9hj
vuVMAP9B3WLzszen3/XCM2E6sZurtmD+YPkUrbES2AsEE1PH3gEA73ZxM1C+gvKS
5be7Dksgeyqyqrwhb9/VOyHU3pmyrAw=
=zirQ
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- some cleanups in the Xen blkback driver
- fix potential sleeps under lock in various Xen drivers
* tag 'for-linus-6.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/blkback: move blkif_get_x86_*_req() into blkback.c
xen/blkback: simplify free_persistent_gnts() interface
xen/blkback: remove stale prototype
xen/blkback: fix white space code style issues
xen/pvcalls: don't call bind_evtchn_to_irqhandler() under lock
xen/scsiback: don't call scsiback_free_translation_entry() under lock
xen/pciback: don't call pcistub_device_put() under lock
Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening in
the driver core in the quest to be able to move "struct bus" and "struct
class" into read-only memory, a task now complete with these changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules for
all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most of
them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZEp7Sw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykitQCfamUHpxGcKOAGuLXMotXNakTEsxgAoIquENm5
LEGadNS38k5fs+73UaxV
=7K4B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
-----BEGIN PGP SIGNATURE-----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=W1Zb
-----END PGP SIGNATURE-----
Merge tag 'for-6.4/block-2023-04-21' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- drbd patches, bringing us closer to unifying the out-of-tree version
and the in tree one (Andreas, Christoph)
- support for auto-quiesce for the s390 dasd driver (Stefan)
- MD pull request via Song:
- md/bitmap: Optimal last page size (Jon Derrick)
- Various raid10 fixes (Yu Kuai, Li Nan)
- md: add error_handlers for raid0 and linear (Mariusz Tkaczyk)
- NVMe pull request via Christoph:
- Drop redundant pci_enable_pcie_error_reporting (Bjorn Helgaas)
- Validate nvmet module parameters (Chaitanya Kulkarni)
- Fence TCP socket on receive error (Chris Leech)
- Fix async event trace event (Keith Busch)
- Minor cleanups (Chaitanya Kulkarni, zhenwei pi)
- Fix and cleanup nvmet Identify handling (Damien Le Moal,
Christoph Hellwig)
- Fix double blk_mq_complete_request race in the timeout handler
(Lei Yin)
- Fix irq locking in nvme-fcloop (Ming Lei)
- Remove queue mapping helper for rdma devices (Sagi Grimberg)
- use structured request attribute checks for nbd (Jakub)
- fix blk-crypto race conditions between keyslot management (Eric)
- add sed-opal support for reading read locking range attributes
(Ondrej)
- make fault injection configurable for null_blk (Akinobu)
- clean up the request insertion API (Christoph)
- clean up the queue running API (Christoph)
- blkg config helper cleanups (Tejun)
- lazy init support for blk-iolatency (Tejun)
- various fixes and tweaks to ublk (Ming)
- remove hybrid polling. It hasn't really been useful since we got
async polled IO support, and these days we don't support sync polled
IO at all (Keith)
- misc fixes, cleanups, improvements (Zhong, Ondrej, Colin, Chengming,
Chaitanya, me)
* tag 'for-6.4/block-2023-04-21' of git://git.kernel.dk/linux: (118 commits)
nbd: fix incomplete validation of ioctl arg
ublk: don't return 0 in case of any failure
sed-opal: geometry feature reporting command
null_blk: Always check queue mode setting from configfs
block: ublk: switch to ioctl command encoding
blk-mq: fix the blk_mq_add_to_requeue_list call in blk_kick_flush
block, bfq: Fix division by zero error on zero wsum
fault-inject: fix build error when FAULT_INJECTION_CONFIGFS=y and CONFIGFS_FS=m
block: store bdev->bd_disk->fops->submit_bio state in bdev
block: re-arrange the struct block_device fields for better layout
md/raid5: remove unused working_disks variable
md/raid10: don't call bio_start_io_acct twice for bio which experienced read error
md/raid10: fix memleak of md thread
md/raid10: fix memleak for 'conf->bio_split'
md/raid10: fix leak of 'r10bio->remaining' for recovery
md/raid10: don't BUG_ON() in raise_barrier()
md: fix soft lockup in status_resync
md: add error_handlers for raid0 and linear
md: Use optimal I/O size for last bitmap page
md: Fix types in sb writer
...
These are various cleanups, fixing a number of uapi header files to no
longer reference CONFIG_* symbols, and one patch that introduces the
new CONFIG_HAS_IOPORT symbol for architectures that provide working
inb()/outb() macros, as a preparation for adding driver dependencies
on those in the following release.
-----BEGIN PGP SIGNATURE-----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=H3k4
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"These are various cleanups, fixing a number of uapi header files to no
longer reference CONFIG_* symbols, and one patch that introduces the
new CONFIG_HAS_IOPORT symbol for architectures that provide working
inb()/outb() macros, as a preparation for adding driver dependencies
on those in the following release"
* tag 'asm-generic-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
Kconfig: introduce HAS_IOPORT option and select it as necessary
scripts: Update the CONFIG_* ignore list in headers_install.sh
pktcdvd: Remove CONFIG_CDROM_PKTCDVD_WCACHE from uapi header
Move bp_type_idx to include/linux/hw_breakpoint.h
Move ep_take_care_of_epollwakeup() to fs/eventpoll.c
Move COMPAT_ATM_ADDPARTY to net/atm/svc.c
QUEUE_FLAG_ADD_RANDOM is not set before we clear it for "null_blk",
"brd", "nbd", "zram", and "bcache" since by default we don't set
"QUEUE_FLAG_ADD_RANDOM" to MQ ops.
Remove dead clear of QUEUE_FLAG_ADD_RANDOM in above listed drivers.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org> #zram
Link: https://lore.kernel.org/r/20230424234628.45544-2-kch@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is no need to have the functions blkif_get_x86_32_req() and
blkif_get_x86_64_req() in a header file, as they are used in one place
only.
So move them into the using source file and drop the inline qualifier.
While at it fix some style issues, and simplify the code by variable
reusing and using min() instead of open coding it.
Instead of using barrier() use READ_ONCE() for avoiding multiple reads
of nr_segments.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
The interface of free_persistent_gnts() can be simplified, as there is
only a single caller of free_persistent_gnts() and the 2nd and 3rd
parameters are easily obtainable via the ring pointer, which is passed
as the first parameter anyway.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
There is no function xen_blkif_purge_persistent(), so remove its
prototype from common.h.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
o MAINTAINERS files additions and changes.
o Fix hotplug warning in nohz code.
o Tick dependency changes by Zqiang.
o Lazy-RCU shrinker fixes by Zqiang.
o rcu-tasks stall reporting improvements by Neeraj.
o Initial changes for renaming of k[v]free_rcu() to its new k[v]free_rcu_mightsleep()
name for robustness.
o Documentation Updates:
o Significant changes to srcu_struct size.
o Deadlock detection for srcu_read_lock() vs synchronize_srcu() from Boqun.
o rcutorture and rcu-related tool, which are targeted for v6.4 from Boqun's tree.
o Other misc changes.
-----BEGIN PGP SIGNATURE-----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=Rgbj
-----END PGP SIGNATURE-----
Merge tag 'rcu.6.4.april5.2023.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jfern/linux
Pull RCU updates from Joel Fernandes:
- Updates and additions to MAINTAINERS files, with Boqun being added to
the RCU entry and Zqiang being added as an RCU reviewer.
I have also transitioned from reviewer to maintainer; however, Paul
will be taking over sending RCU pull-requests for the next merge
window.
- Resolution of hotplug warning in nohz code, achieved by fixing
cpu_is_hotpluggable() through interaction with the nohz subsystem.
Tick dependency modifications by Zqiang, focusing on fixing usage of
the TICK_DEP_BIT_RCU_EXP bitmask.
- Avoid needless calls to the rcu-lazy shrinker for CONFIG_RCU_LAZY=n
kernels, fixed by Zqiang.
- Improvements to rcu-tasks stall reporting by Neeraj.
- Initial renaming of k[v]free_rcu() to k[v]free_rcu_mightsleep() for
increased robustness, affecting several components like mac802154,
drbd, vmw_vmci, tracing, and more.
A report by Eric Dumazet showed that the API could be unknowingly
used in an atomic context, so we'd rather make sure they know what
they're asking for by being explicit:
https://lore.kernel.org/all/20221202052847.2623997-1-edumazet@google.com/
- Documentation updates, including corrections to spelling,
clarifications in comments, and improvements to the srcu_size_state
comments.
- Better srcu_struct cache locality for readers, by adjusting the size
of srcu_struct in support of SRCU usage by Christoph Hellwig.
- Teach lockdep to detect deadlocks between srcu_read_lock() vs
synchronize_srcu() contributed by Boqun.
Previously lockdep could not detect such deadlocks, now it can.
- Integration of rcutorture and rcu-related tools, targeted for v6.4
from Boqun's tree, featuring new SRCU deadlock scenarios, test_nmis
module parameter, and more
- Miscellaneous changes, various code cleanups and comment improvements
* tag 'rcu.6.4.april5.2023.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jfern/linux: (71 commits)
checkpatch: Error out if deprecated RCU API used
mac802154: Rename kfree_rcu() to kvfree_rcu_mightsleep()
rcuscale: Rename kfree_rcu() to kfree_rcu_mightsleep()
ext4/super: Rename kfree_rcu() to kfree_rcu_mightsleep()
net/mlx5: Rename kfree_rcu() to kfree_rcu_mightsleep()
net/sysctl: Rename kvfree_rcu() to kvfree_rcu_mightsleep()
lib/test_vmalloc.c: Rename kvfree_rcu() to kvfree_rcu_mightsleep()
tracing: Rename kvfree_rcu() to kvfree_rcu_mightsleep()
misc: vmw_vmci: Rename kvfree_rcu() to kvfree_rcu_mightsleep()
drbd: Rename kvfree_rcu() to kvfree_rcu_mightsleep()
rcu: Protect rcu_print_task_exp_stall() ->exp_tasks access
rcu: Avoid stack overflow due to __rcu_irq_enter_check_tick() being kprobe-ed
rcu-tasks: Report stalls during synchronize_srcu() in rcu_tasks_postscan()
rcu: Permit start_poll_synchronize_rcu_expedited() to be invoked early
rcu: Remove never-set needwake assignment from rcu_report_qs_rdp()
rcu: Register rcu-lazy shrinker only for CONFIG_RCU_LAZY=y kernels
rcu: Fix missing TICK_DEP_MASK_RCU_EXP dependency check
rcu: Fix set/clear TICK_DEP_BIT_RCU_EXP bitmask race
rcu/trace: use strscpy() to instead of strncpy()
tick/nohz: Fix cpu_is_hotpluggable() by checking with nohz subsystem
...
We tested and found an alarm caused by nbd_ioctl arg without verification.
The UBSAN warning calltrace like below:
UBSAN: Undefined behaviour in fs/buffer.c:1709:35
signed integer overflow:
-9223372036854775808 - 1 cannot be represented in type 'long long int'
CPU: 3 PID: 2523 Comm: syz-executor.0 Not tainted 4.19.90 #1
Hardware name: linux,dummy-virt (DT)
Call trace:
dump_backtrace+0x0/0x3f0 arch/arm64/kernel/time.c:78
show_stack+0x28/0x38 arch/arm64/kernel/traps.c:158
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x170/0x1dc lib/dump_stack.c:118
ubsan_epilogue+0x18/0xb4 lib/ubsan.c:161
handle_overflow+0x188/0x1dc lib/ubsan.c:192
__ubsan_handle_sub_overflow+0x34/0x44 lib/ubsan.c:206
__block_write_full_page+0x94c/0xa20 fs/buffer.c:1709
block_write_full_page+0x1f0/0x280 fs/buffer.c:2934
blkdev_writepage+0x34/0x40 fs/block_dev.c:607
__writepage+0x68/0xe8 mm/page-writeback.c:2305
write_cache_pages+0x44c/0xc70 mm/page-writeback.c:2240
generic_writepages+0xdc/0x148 mm/page-writeback.c:2329
blkdev_writepages+0x2c/0x38 fs/block_dev.c:2114
do_writepages+0xd4/0x250 mm/page-writeback.c:2344
The reason for triggering this warning is __block_write_full_page()
-> i_size_read(inode) - 1 overflow.
inode->i_size is assigned in __nbd_ioctl() -> nbd_set_size() -> bytesize.
We think it is necessary to limit the size of arg to prevent errors.
Moreover, __nbd_ioctl() -> nbd_add_socket(), arg will be cast to int.
Assuming the value of arg is 0x80000000000000001) (on a 64-bit machine),
it will become 1 after the coercion, which will return unexpected results.
Fix it by adding checks to prevent passing in too large numbers.
Signed-off-by: Zhong Jinghua <zhongjinghua@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20230206145805.2645671-1-zhongjinghua@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 2d786e66c9 ("block: ublk: switch to ioctl command encoding")
starts to reset local variable of 'ret' as zero, then if any failure
happens when handling the three IO commands, 0 can be returned to ublk
server.
Fix it by returning -EINVAL in case of command handling failure.
Cc: Christoph Hellwig <hch@lst.de>
Fixes: 2d786e66c9 ("block: ublk: switch to ioctl command encoding")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230420091104.1092972-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All ublk commands(control, IO) should have taken ioctl command encoding
from the beginning, because ioctl command encoding defines each code
uniquely, so driver can figure out wrong command sent from userspace
easily; 2) it might help security subsystem for audit uring cmd[1].
Unfortunately we didn't do that way, and it could be one lesson for
ublk driver.
So switch to ioctl command encoding now, we still support commands encoded
in old way, but they become legacy definition. Any new command should take
ioctl encoding.
See ublksrv code for switching to ioctl command encoding in [2].
[1] https://lore.kernel.org/io-uring/CAHC9VhSVzujW9LOj5Km80AjU0EfAuukoLrxO6BEfnXeK_s6bAg@mail.gmail.com/
[2] https://github.com/ming1/ubdsrv/commits/ioctl_cmd_encoding
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ken Kurematsu <k.kurematsu@nskint.co.jp>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230418131810.855959-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Propagate read errors to the caller instead of dropping them on the floor,
and stop returning the somewhat dangerous 1 on success from
read_from_bdev*.
Link: https://lkml.kernel.org/r/20230411171459.567614-18-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Currently nothing waits for the synchronous reads before accessing the
data. Switch them to an on-stack bio and submit_bio_wait to make sure the
I/O has actually completed when the work item has been flushed. This also
removes the call to page_endio that would unlock a page that has never
been locked.
Drop the partial_io/sync flag, as chaining only makes sense for the
asynchronous reads of the entire page.
Link: https://lkml.kernel.org/r/20230411171459.567614-17-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
bio_alloc will never return a NULL bio when it is allowed to sleep, and
adding a single page to bio with a single vector also can't fail, so
switch to the asserting __bio_add_page variant and drop the error returns.
Link: https://lkml.kernel.org/r/20230411171459.567614-16-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
read_from_bdev always reads a whole page, so pass a page to it instead of
the bvec and remove the now pointless zram_bvec_read_from_bdev wrapper.
Link: https://lkml.kernel.org/r/20230411171459.567614-15-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Split the read/modify/write case into a separate helper.
Link: https://lkml.kernel.org/r/20230411171459.567614-14-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
__zram_bvec_write only extracts the page from __zram_bvec_write and always
expects a full page of input. Pass the page directly instead of the bvec
and rename the function to zram_write_page.
Link: https://lkml.kernel.org/r/20230411171459.567614-13-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Split the partial read into a separate helper.
Link: https://lkml.kernel.org/r/20230411171459.567614-12-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
writeback_store always reads a full page, so just call zram_read_page
directly and bypass the boune buffer handling.
Link: https://lkml.kernel.org/r/20230411171459.567614-11-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
__zram_bvec_read doesn't get passed a bvec, but always read a whole page.
Rename it to make the usage more clear.
Link: https://lkml.kernel.org/r/20230411171459.567614-10-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
There is no point in allocation a highmem page when we instantly need to
copy from it.
Link: https://lkml.kernel.org/r/20230411171459.567614-9-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Instead of having an outer loop in __zram_make_request and then branch out
for reads vs writes for each loop iteration in zram_bvec_rw, split the
main handler into separat zram_bio_read and zram_bio_write handlers that
also include the functionality formerly in zram_bvec_rw.
Link: https://lkml.kernel.org/r/20230411171459.567614-8-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
When the low-level access fails, don't clear the idle flag or clear the
caches, and just return.
Link: https://lkml.kernel.org/r/20230411171459.567614-7-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Switch on the bio operation in zram_submit_bio and only call into
__zram_make_request for read and write operations.
Link: https://lkml.kernel.org/r/20230411171459.567614-6-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
bio_for_each_segment synthetize bvecs that never cross page boundaries, so
don't duplicate that work in an inner loop.
Link: https://lkml.kernel.org/r/20230411171459.567614-5-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Derive the index and offset variables inside the function, and complete
the bio directly in preparation for cleaning up the I/O path.
Link: https://lkml.kernel.org/r/20230411171459.567614-4-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
All bios hande to drivers from the block layer are checked against the
device size and for logical block alignment already (and have been since
long before zram was merged), so don't duplicate those checks.
Link: https://lkml.kernel.org/r/20230411171459.567614-3-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "zram I/O path cleanups and fixups", v3.
This series cleans up the zram I/O path, and fixes the handling of
synchronous I/O to the underlying device in the writeback_store function
or for > 4K PAGE_SIZE systems.
The fixes are at the end, as I could not fully reason about them being
safe before untangling the callchain.
This patch (of 17):
read_from_bdev_sync is currently only compiled for non-4k PAGE_SIZE, which
means it won't be built with the most common configurations.
Replace the ifdef with a check for the PAGE_SIZE in an if instead. The
check uses an extra symbol and IS_ENABLED to allow the compiler to
eliminate the dead code, leading to the same generated code size:
text data bss dec hex filename
16709 1428 12 18149 46e5 drivers/block/zram/zram_drv.o.old
16709 1428 12 18149 46e5 drivers/block/zram/zram_drv.o.new
Link: https://lkml.kernel.org/r/20230411171459.567614-1-hch@lst.de
Link: https://lkml.kernel.org/r/20230411171459.567614-2-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Commit 75a2d4226b ("driver core: class: mark the struct class for
sysfs callbacks as constant") changed the attribute to use
CLASS_ATTR_RO() which changed the permission from 0400 to 0444. But
this atribute is "special" in that reading it modifies the system state,
so it MUST be set to 0400 so that only root processes can muck around
with it.
Fix this all up, AND document this so that I don't change it again in
3-4 years when I stumble across it and wonder why it's an open-coded
_ATTR() macro.
Reported-by: Denis Efremov <efremov@linux.com>
Fixes: 75a2d4226b ("driver core: class: mark the struct class for sysfs callbacks as constant")
Link: https://lore.kernel.org/r/2023041810-angelic-conical-52d8@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The null_blk driver has multiple driver-specific fault injection
mechanisms. Each fault injection configuration can only be specified by a
module parameter and cannot be reconfigured without reloading the driver.
Also, each configuration is common to all devices and is initialized every
time a new device is added.
This change adds the following subdirectories for each null_blk device.
/sys/kernel/config/nullb/<disk>/timeout_inject
/sys/kernel/config/nullb/<disk>/requeue_inject
/sys/kernel/config/nullb/<disk>/init_hctx_fault_inject
Each fault injection attribute can be dynamically set per device by a
corresponding file in these directories.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Link: https://lore.kernel.org/r/20230327143733.14599-3-akinobu.mita@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Some last minute fixes - most of them for regressions.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmQz3aoPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp/MQIAJ0uzzyTAg7Bx/73M7JZckxgScyVOI/192mw
ylT/1EZrlZi8JOC1uf9gC+fHlg4jgS/0Yn6HSJlBH0CAJPRNpGckzA1aEr/gc9jS
2wWxCrUeO2hvlMN7HToesmZxu79xKDIoYIFnwVV/IDLTi9Y8Fh+hUIkRR16IBiXb
dgrI2qkYvyqGj5hJDnM9MaMVbTARYXb2q2SgiqGjh/TUNrkqDI0e0m1tj9eXNR90
uIz1lfbIH6JKiq2Zq/CK+h87dMOVBNoH+LZvMRKPx0beEfxC4P/1Re1Rag12kG1s
TE7n556BOsqBQ333+rIgtNSq2dDAepG+CASZsR6Dw4F+41G43Qo=
=WjYr
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"Some last minute fixes - most of them for regressions"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa_sim_net: complete the initialization before register the device
vdpa/mlx5: Add and remove debugfs in setup/teardown driver
tools/virtio: fix typo in README instructions
vhost-scsi: Fix crash during LUN unmapping
vhost-scsi: Fix vhost_scsi struct use after free
virtio-blk: fix ZBD probe in kernels without ZBD support
virtio-blk: fix to match virtio spec
block size is one very key setting for block layer, and bad block size
could panic kernel easily.
Make sure that block size is set correctly.
Meantime if ublk_validate_params() fails, clear ub->params so that disk
is prevented from being added.
Fixes: 71f28f3136 ("ublk_drv: add io_uring based userspace block driver")
Reported-and-tested-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since SQE memory is shared with userspace, we should only be reading it
once. We cannot read it multiple times, particularly when it's read once
for validation and then read again for the actual use.
ublk_ch_uring_cmd() is safe when called as a retry operation, as the
memory backing is stable at that point. But for normal issue, we want
to ensure that we only read ublksrv_io_cmd once. Wrap the function in
a helper that reads the value into an on-stack copy of the struct.
Cc: stable@vger.kernel.org # 6.0+
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
MAX_ORDER is not inclusive: the maximum allocation order buddy allocator
can deliver is MAX_ORDER-1.
Fix MAX_ORDER usage in floppy code.
Also allocation buffer exactly PAGE_SIZE << MAX_ORDER bytes is okay. Fix
MAX_LEN check.
Link: https://lkml.kernel.org/r/20230315113133.11326-4-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Denis Efremov <efremov@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kvfree_rcu() macro's single-argument form is deprecated. Therefore
switch to the new kvfree_rcu_mightsleep() variant. The goal is to
avoid accidental use of the single-argument forms, which can introduce
functionality bugs in atomic contexts and latency bugs in non-atomic
contexts.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Begrudgingly-acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
When the kernel is built without support for zoned block devices,
virtio-blk probe needs to error out any host-managed device scans
to prevent such devices from appearing in the system as non-zoned.
The current virtio-blk code simply bypasses all ZBD checks if
CONFIG_BLK_DEV_ZONED is not defined and this leads to host-managed
block devices being presented as non-zoned in the OS. This is one of
the main problems this patch series is aimed to fix.
In this patch, make VIRTIO_BLK_F_ZONED feature defined even when
CONFIG_BLK_DEV_ZONED is not. This change makes the code compliant with
the voted revision of virtio-blk ZBD spec. Modify the probe code to
look at the situation when VIRTIO_BLK_F_ZONED is negotiated in a kernel
that is built without ZBD support. In this case, the code checks
the zoned model of the device and fails the probe is the device
is host-managed.
The patch also adds the comment to clarify that the call to perform
the zoned device probe is correctly placed after virtio_device ready().
Fixes: 95bfec41bd ("virtio-blk: add support for zoned block devices")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Message-Id: <20230330214953.1088216-3-dmitry.fomichev@wdc.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The merged patch series to support zoned block devices in virtio-blk
is not the most up to date version. The merged patch can be found at
https://lore.kernel.org/linux-block/20221016034127.330942-3-dmitry.fomichev@wdc.com/
but the latest and reviewed version is
https://lore.kernel.org/linux-block/20221110053952.3378990-3-dmitry.fomichev@wdc.com/
The reason is apparently that the correct mailing lists and
maintainers were not copied.
The differences between the two are mostly cleanups, but there is one
change that is very important in terms of compatibility with the
approved virtio-zbd specification.
Before it was approved, the OASIS virtio spec had a change in
VIRTIO_BLK_T_ZONE_APPEND request layout that is not reflected in the
current virtio-blk driver code. In the running code, the status is
the first byte of the in-header that is followed by some pad bytes
and the u64 that carries the sector at which the data has been written
to the zone back to the driver, aka the append sector.
This layout turned out to be problematic for implementing in QEMU and
the request status byte has been eventually made the last byte of the
in-header. The current code doesn't expect that and this causes the
append sector value always come as zero to the block layer. This needs
to be fixed ASAP.
Fixes: 95bfec41bd ("virtio-blk: add support for zoned block devices")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Message-Id: <20230330214953.1088216-2-dmitry.fomichev@wdc.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We need the fixes in here for testing, as well as the driver core
changes for documentation updates to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'struct ublk_map_data' is passed to ublk_copy_user_pages()
for copying data between userspace buffer and request pages.
Here what matters is userspace buffer address/len and 'struct request',
so replace ->io field with user buffer address, and rename max_bytes
as len.
Meantime remove 'ubq' field from ublk_map_data, since it isn't used
any more.
Then code becomes more readable.
Reviewed-by: Ziyang Zhang <ZiyangZhang@linux.alibaba.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Convert the following pattern in several helpers
if (Z)
return true
return false
into:
return Z;
Reviewed-by: Ziyang Zhang <ZiyangZhang@linux.alibaba.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add two helpers for checking if map/unmap is needed, since we may have
passthrough request which needs map or unmap in future, such as for
supporting report zones.
Meantime don't mark ublk_copy_user_pages as inline since this function
is a bit fat now.
Reviewed-by: Ziyang Zhang <ZiyangZhang@linux.alibaba.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There isn't data in request of REQ_OP_FLUSH always, so don't consider
it in both ublk_map_io() and ublk_unmap_io().
Reviewed-by: Ziyang Zhang <ZiyangZhang@linux.alibaba.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Simplify exit handling a bit, and prepare for supporting fused command.
Reviewed-by: Ziyang Zhang <ZiyangZhang@linux.alibaba.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In preparation to support multiple connections, we need to know which
one we need to modify the request state for.
Originally-from: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20230330102744.2128122-2-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass a peer device parameter through the bitmap I/O functions to the I/O
handlers. In after_state_ch(), set that parameter when queuing the
drbd_send_bitmap operation so that this operation knows where to send the
bitmap.
Signed-off-by: Andreas Gruenbacher <agruen@kernel.org>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20230330102744.2128122-2-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace the deprecated API kmap_atomic() and kunmap_atomic() with
kmap_local_page() and kunmap_local() in null_flush_cache_page().
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20230330184926.64209-2-kch@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use library helper memcpy_page() to copy source page into destination
instead of having duplicate code in copy_to_nullb() & copy_from_nullb().
In copy_from_nullb() also replace the memset call with zero_user().
Use library helper memset_page() to set the buffer to 0xFF instead of
having duplicate code.
This also removes deprecated API kmap_atomic() from copy_to_nullb()
copy_from_nullb() and nullb_fill_pattern(),
from :include/linux/highmem.h:
"kmap_atomic - Atomically map a page for temporary usage - Deprecated!"
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20230330184926.64209-2-kch@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
struct class should never be modified in a sysfs callback as there is
nothing in the structure to modify, and frankly, the structure is almost
never used in a sysfs callback, so mark it as constant to allow struct
class to be moved to read-only memory.
While we are touching all class sysfs callbacks also mark the attribute
as constant as it can not be modified. The bonding code still uses this
structure so it can not be removed from the function callbacks.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Russ Weight <russell.h.weight@intel.com>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Steve French <sfrench@samba.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-cifs@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-rdma@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: netdev@vger.kernel.org
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20230325084537.3622280-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LOOP_CONFIGURE is, as far as I understand it, supposed to be a way to
combine LOOP_SET_FD and LOOP_SET_STATUS64 into a single syscall. When
using LOOP_SET_FD+LOOP_SET_STATUS64, a single uevent would be sent for
each partition found on the loop device after the second ioctl(), but
when using LOOP_CONFIGURE, no such uevent was being sent.
In the old setup, uevents are disabled for LOOP_SET_FD, but not for
LOOP_SET_STATUS64. This makes sense, as it prevents uevents being
sent for a partially configured device during LOOP_SET_FD - they're
only sent at the end of LOOP_SET_STATUS64. But for LOOP_CONFIGURE,
uevents were disabled for the entire operation, so that final
notification was never issued. To fix this, reduce the critical
section to exclude the loop_reread_partitions() call, which causes
the uevents to be issued, to after uevents are re-enabled, matching
the behaviour of the LOOP_SET_FD+LOOP_SET_STATUS64 combination.
I noticed this because Busybox's losetup program recently changed from
using LOOP_SET_FD+LOOP_SET_STATUS64 to LOOP_CONFIGURE, and this broke
my setup, for which I want a notification from the kernel any time a
new partition becomes available.
Signed-off-by: Alyssa Ross <hi@alyssa.is>
[hch: reduced the critical section]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: 3448914e8c ("loop: Add LOOP_CONFIGURE ioctl")
Link: https://lore.kernel.org/r/20230320125430.55367-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
struct bus_type should never be modified in a sysfs callback as there is
nothing in the structure to modify, and frankly, the structure is almost
never used in a sysfs callback, so mark it as constant to allow struct
bus_type to be moved to read-only memory.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Alexandre Bounine <alex.bou9@gmail.com>
Cc: Alison Schofield <alison.schofield@intel.com>
Cc: Ben Widawsky <bwidawsk@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Hu Haowen <src.res@email.cn>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Stuart Yoder <stuyoder@gmail.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Yanteng Si <siyanteng@loongson.cn>
Acked-by: Ilya Dryomov <idryomov@gmail.com> # rbd
Acked-by: Ira Weiny <ira.weiny@intel.com> # cxl
Reviewed-by: Alex Shi <alexs@kernel.org>
Acked-by: Iwona Winiarska <iwona.winiarska@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # pci
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # scsi
Link: https://lore.kernel.org/r/20230313182918.1312597-23-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
io_uring_cmd_done() currently assumes that the uring_lock is held
when invoked, and while it generally is, this is not guaranteed.
Pass in the issue_flags associated with it, so that we have
IO_URING_F_UNLOCKED available to be able to lock the CQ ring
appropriately when completing events.
Cc: stable@vger.kernel.org
Fixes: ee692a21e9 ("fs,io_uring: add infrastructure for uring-cmd")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
IO can be started before add_disk() returns, such as reading parititon table,
then the monitor work should work for making forward progress.
So mark device as LIVE before adding disk, meantime change to
DEAD if add_disk() fails.
Fixed: 71f28f3136 ("ublk_drv: add io_uring based userspace block driver")
Reviewed-by: Ziyang Zhang <ZiyangZhang@linux.alibaba.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230318141231.55562-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The module pointer in class_create() never actually did anything, and it
shouldn't have been requred to be set as a parameter even if it did
something. So just remove it and fix up all callers of the function in
the kernel tree at the same time.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to manually set the owner of a struct class, as the
registering function does it automatically, so remove all of the
explicit settings from various drivers that did so as it is unneeded.
This allows us to remove this pointer entirely from this structure going
forward.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Link: https://lore.kernel.org/r/20230313181843.1207845-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In vdc_port_probe(), we should check the return value of mdesc_grab() as
it may return NULL, which can cause potential NPD bug.
Fixes: 43fdf27470 ("[SPARC64]: Abstract out mdesc accesses for better MD update handling.")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20230315062032.1741692-1-windhl@126.com
[axboe: style cleanup]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use a local struct request pointer variable to avoid having to
dereference struct blk_mq_queue_data multiple times. While at it, also
fix the function argument indentation and remove a useless "else" after
a return.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Pankaj Raghav <p.raghav@samsung.com>
Link: https://lore.kernel.org/r/20230314041106.19173-2-damien.lemoal@opensource.wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When injecting a fake timeout into the null_blk driver using
fail_io_timeout, the request timeout handler does not execute
blk_mq_complete_request(), so the complete callback is never executed
for a timedout request.
The null_blk driver also has a driver-specific fake timeout mechanism
which does not have this problem. Fix the problem with fail_io_timeout
by using the same meachanism as null_blk internal timeout feature, using
the fake_timeout field of null_blk commands.
Reported-by: Akinobu Mita <akinobu.mita@gmail.com>
Fixes: de3510e52b ("null_blk: fix command timeout completion handling")
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20230314041106.19173-2-damien.lemoal@opensource.wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
do_req_filebacked() calls blk_mq_complete_request() synchronously or
asynchronously when using asynchronous I/O unless memory allocation fails.
Hence, modify loop_handle_cmd() such that it does not dereference 'cmd' nor
'rq' after do_req_filebacked() finished unless we are sure that the request
has not yet been completed. This patch fixes the following kernel crash:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000054
Call trace:
css_put.42938+0x1c/0x1ac
loop_process_work+0xc8c/0xfd4
loop_rootcg_workfn+0x24/0x34
process_one_work+0x244/0x558
worker_thread+0x400/0x8fc
kthread+0x16c/0x1e0
ret_from_fork+0x10/0x20
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dan Schatzberg <schatzberg.dan@gmail.com>
Fixes: c74d40e8b5 ("loop: charge i/o to mem and blk cg")
Fixes: bc07c10a36 ("block: loop: support DIO & AIO")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230314182155.80625-1-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use the macro for checking presence of required attributes.
It has the advantage of reporting to the user which attr
was missing in a machine-readable format (extack).
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20230224021301.1630703-2-kuba@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
NBD doesn't have much to do with networking, allow users outside
init_net to access the family.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20230224021301.1630703-1-kuba@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
CONFIG_* switches should not be exposed in uapi headers, thus let's get
rid of the USE_WCACHING macro here (which was also named way to generic)
and integrate the logic directly in the only function that needs it.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=ezrg
-----END PGP SIGNATURE-----
Merge tag 'block-6.3-2023-03-03' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- NVMe pull request via Christoph:
- Don't access released socket during error recovery (Akinobu
Mita)
- Bring back auto-removal of deleted namespaces during sequential
scan (Christoph Hellwig)
- Fix an error code in nvme_auth_process_dhchap_challenge (Dan
Carpenter)
- Show well known discovery name (Daniel Wagner)
- Add a missing endianess conversion in effects masking (Keith
Busch)
- Fix for a regression introduced in blk-rq-qos during init in this
merge window (Breno)
- Reorder a few fields in struct blk_mq_tag_set, eliminating a few
holes and shrinking it (Christophe)
- Remove redundant bdev_get_queue() NULL checks (Juhyung)
- Add sed-opal single user mode support flag (Luca)
- Remove SQE128 check in ublk as it isn't needed, saving some memory
(Ming)
- Op specific segment checking for cloned requests (Uday)
- Exclusive open partition scan fixes (Yu)
- Loop offset/size checking before assigning them in the device (Zhong)
- Bio polling fixes (me)
* tag 'block-6.3-2023-03-03' of git://git.kernel.dk/linux:
blk-mq: enforce op-specific segment limits in blk_insert_cloned_request
nvme-fabrics: show well known discovery name
nvme-tcp: don't access released socket during error recovery
nvme-auth: fix an error code in nvme_auth_process_dhchap_challenge()
nvme: bring back auto-removal of deleted namespaces during sequential scan
blk-iocost: Pass gendisk to ioc_refresh_params
nvme: fix sparse warning on effects masking
block: be a bit more careful in checking for NULL bdev while polling
block: clear bio->bi_bdev when putting a bio back in the cache
loop: loop_set_status_from_info() check before assignment
ublk: remove check IO_URING_F_SQE128 in ublk_ch_uring_cmd
block: remove more NULL checks after bdev_get_queue()
blk-mq: Reorder fields in 'struct blk_mq_tag_set'
block: fix scan partition for exclusively open device again
block: Revert "block: Do not reread partition table on exclusively open device"
sed-opal: add support flag for SUM in status ioctl
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmQA0uETHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi92pB/4yZ7Go/7j2zb84N9nEYPCHV23v1vED
YGZIiWHYv6X3dJyTYpcU7Mn9TF00naTGDKi9NpTZjKOUIkibXPFJfbG7Dh4T2HhN
TKw9EbldCaXE1mR7o+g/mrVQFM1PIR1VbtIeszL3eD2qO0aXEGyBMvPfUNqFX/M7
lNWVjuglIaYUL235Uid/wt0zfmPDvtGD24fjpN0e22UQh/aBFnodIDpa/AapsFKp
yifzqe/ADbvgnHwOhMiEMG1gRFd3vywVfPDQmQ41oSMnf7yTtLWE9t47wTfyoTY5
IwZY2K1H51QJej/mObYJmClp/y81xSLXEydFdQ571MqZbDeDfQeM23/7
=cWWl
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-6.3-rc1' of https://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"Two small fixes from Xiubo and myself, marked for stable"
* tag 'ceph-for-6.3-rc1' of https://github.com/ceph/ceph-client:
rbd: avoid use-after-free in do_rbd_add() when rbd_dev_create() fails
ceph: update the time stamps and try to drop the suid/sgid
If getting an ID or setting up a work queue in rbd_dev_create() fails,
use-after-free on rbd_dev->rbd_client, rbd_dev->spec and rbd_dev->opts
is triggered in do_rbd_add(). The root cause is that the ownership of
these structures is transfered to rbd_dev prematurely and they all end
up getting freed when rbd_dev_create() calls rbd_dev_free() prior to
returning to do_rbd_add().
Found by Linux Verification Center (linuxtesting.org) with SVACE, an
incomplete patch submitted by Natalia Petrova <n.petrova@fintech.ru>.
Cc: stable@vger.kernel.org
Fixes: 1643dfa4c2 ("rbd: introduce a per-device ordered workqueue")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
device feature provisioning in ifcvf, mlx5
new SolidNET driver
support for zoned block device in virtio blk
numa support in virtio pmem
VIRTIO_F_RING_RESET support in vhost-net
more debugfs entries in mlx5
resume support in vdpa
completion batching in virtio blk
cleanup of dma api use in vdpa
now simulating more features in vdpa-sim
documentation, features, fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmP0D98PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpV6IH/iecRgLMWWjp3n31IFdu31f/J4HpF7dczVjK
qtV98eJ1N2pkgeJkdCfmB5XszfvFBeAurrS7++FTHiJhrRfR3Z+2ml/Qtvh5DEyP
qxz6wOw6VVsi/txdUxM1wsxLeEmmzkmFdAmPM+FXeIjhWj76GOgy/4A3eaj6TgzV
W8ShsBve/UZ5qMOC3XbIscvdOrudHJ18tH90Tiz3NZfH1fAs5E4uWbU6Mrz9DJVr
canGvf4kAI9z8qram5HSgzPIXRJEYiF4q/eiStdtiiME8gL1mHLRZDNP1I1LeCAb
q6Q6RCRKi3Ek+LGdH6u+nR1Swu03N2b/g+vgKtv30kJo06oZVzw=
=EasV
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
- device feature provisioning in ifcvf, mlx5
- new SolidNET driver
- support for zoned block device in virtio blk
- numa support in virtio pmem
- VIRTIO_F_RING_RESET support in vhost-net
- more debugfs entries in mlx5
- resume support in vdpa
- completion batching in virtio blk
- cleanup of dma api use in vdpa
- now simulating more features in vdpa-sim
- documentation, features, fixes all over the place
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (64 commits)
vdpa/mlx5: support device features provisioning
vdpa/mlx5: make MTU/STATUS presence conditional on feature bits
vdpa: validate device feature provisioning against supported class
vdpa: validate provisioned device features against specified attribute
vdpa: conditionally read STATUS in config space
vdpa: fix improper error message when adding vdpa dev
vdpa/mlx5: Initialize CVQ iotlb spinlock
vdpa/mlx5: Don't clear mr struct on destroy MR
vdpa/mlx5: Directly assign memory key
tools/virtio: enable to build with retpoline
vringh: fix a typo in comments for vringh_kiov
vhost-vdpa: print warning when vhost_vdpa_alloc_domain fails
scsi: virtio_scsi: fix handling of kmalloc failure
vdpa: Fix a couple of spelling mistakes in some messages
vhost-net: support VIRTIO_F_RING_RESET
vhost-scsi: convert sysfs snprintf and sprintf to sysfs_emit
vdpa: mlx5: support per virtqueue dma device
vdpa: set dma mask for vDPA device
virtio-vdpa: support per vq dma device
vdpa: introduce get_vq_dma_device()
...
F_SEAL_EXEC") which permits the setting of the memfd execute bit at
memfd creation time, with the option of sealing the state of the X bit.
- Peter Xu adds a patch series ("mm/hugetlb: Make huge_pte_offset()
thread-safe for pmd unshare") which addresses a rare race condition
related to PMD unsharing.
- Several folioification patch serieses from Matthew Wilcox, Vishal
Moola, Sidhartha Kumar and Lorenzo Stoakes
- Johannes Weiner has a series ("mm: push down lock_page_memcg()") which
does perform some memcg maintenance and cleanup work.
- SeongJae Park has added DAMOS filtering to DAMON, with the series
"mm/damon/core: implement damos filter". These filters provide users
with finer-grained control over DAMOS's actions. SeongJae has also done
some DAMON cleanup work.
- Kairui Song adds a series ("Clean up and fixes for swap").
- Vernon Yang contributed the series "Clean up and refinement for maple
tree".
- Yu Zhao has contributed the "mm: multi-gen LRU: memcg LRU" series. It
adds to MGLRU an LRU of memcgs, to improve the scalability of global
reclaim.
- David Hildenbrand has added some userfaultfd cleanup work in the
series "mm: uffd-wp + change_protection() cleanups".
- Christoph Hellwig has removed the generic_writepages() library
function in the series "remove generic_writepages".
- Baolin Wang has performed some maintenance on the compaction code in
his series "Some small improvements for compaction".
- Sidhartha Kumar is doing some maintenance work on struct page in his
series "Get rid of tail page fields".
- David Hildenbrand contributed some cleanup, bugfixing and
generalization of pte management and of pte debugging in his series "mm:
support __HAVE_ARCH_PTE_SWP_EXCLUSIVE on all architectures with swap
PTEs".
- Mel Gorman and Neil Brown have removed the __GFP_ATOMIC allocation
flag in the series "Discard __GFP_ATOMIC".
- Sergey Senozhatsky has improved zsmalloc's memory utilization with his
series "zsmalloc: make zspage chain size configurable".
- Joey Gouly has added prctl() support for prohibiting the creation of
writeable+executable mappings. The previous BPF-based approach had
shortcomings. See "mm: In-kernel support for memory-deny-write-execute
(MDWE)".
- Waiman Long did some kmemleak cleanup and bugfixing in the series
"mm/kmemleak: Simplify kmemleak_cond_resched() & fix UAF".
- T.J. Alumbaugh has contributed some MGLRU cleanup work in his series
"mm: multi-gen LRU: improve".
- Jiaqi Yan has provided some enhancements to our memory error
statistics reporting, mainly by presenting the statistics on a per-node
basis. See the series "Introduce per NUMA node memory error
statistics".
- Mel Gorman has a second and hopefully final shot at fixing a CPU-hog
regression in compaction via his series "Fix excessive CPU usage during
compaction".
- Christoph Hellwig does some vmalloc maintenance work in the series
"cleanup vfree and vunmap".
- Christoph Hellwig has removed block_device_operations.rw_page() in ths
series "remove ->rw_page".
- We get some maple_tree improvements and cleanups in Liam Howlett's
series "VMA tree type safety and remove __vma_adjust()".
- Suren Baghdasaryan has done some work on the maintainability of our
vm_flags handling in the series "introduce vm_flags modifier functions".
- Some pagemap cleanup and generalization work in Mike Rapoport's series
"mm, arch: add generic implementation of pfn_valid() for FLATMEM" and
"fixups for generic implementation of pfn_valid()"
- Baoquan He has done some work to make /proc/vmallocinfo and
/proc/kcore better represent the real state of things in his series
"mm/vmalloc.c: allow vread() to read out vm_map_ram areas".
- Jason Gunthorpe rationalized the GUP system's interface to the rest of
the kernel in the series "Simplify the external interface for GUP".
- SeongJae Park wishes to migrate people from DAMON's debugfs interface
over to its sysfs interface. To support this, we'll temporarily be
printing warnings when people use the debugfs interface. See the series
"mm/damon: deprecate DAMON debugfs interface".
- Andrey Konovalov provided the accurately named "lib/stackdepot: fixes
and clean-ups" series.
- Huang Ying has provided a dramatic reduction in migration's TLB flush
IPI rates with the series "migrate_pages(): batch TLB flushing".
- Arnd Bergmann has some objtool fixups in "objtool warning fixes".
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCY/PoPQAKCRDdBJ7gKXxA
jlvpAPsFECUBBl20qSue2zCYWnHC7Yk4q9ytTkPB/MMDrFEN9wD/SNKEm2UoK6/K
DmxHkn0LAitGgJRS/W9w81yrgig9tAQ=
=MlGs
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2023-02-20-13-37' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- Daniel Verkamp has contributed a memfd series ("mm/memfd: add
F_SEAL_EXEC") which permits the setting of the memfd execute bit at
memfd creation time, with the option of sealing the state of the X
bit.
- Peter Xu adds a patch series ("mm/hugetlb: Make huge_pte_offset()
thread-safe for pmd unshare") which addresses a rare race condition
related to PMD unsharing.
- Several folioification patch serieses from Matthew Wilcox, Vishal
Moola, Sidhartha Kumar and Lorenzo Stoakes
- Johannes Weiner has a series ("mm: push down lock_page_memcg()")
which does perform some memcg maintenance and cleanup work.
- SeongJae Park has added DAMOS filtering to DAMON, with the series
"mm/damon/core: implement damos filter".
These filters provide users with finer-grained control over DAMOS's
actions. SeongJae has also done some DAMON cleanup work.
- Kairui Song adds a series ("Clean up and fixes for swap").
- Vernon Yang contributed the series "Clean up and refinement for maple
tree".
- Yu Zhao has contributed the "mm: multi-gen LRU: memcg LRU" series. It
adds to MGLRU an LRU of memcgs, to improve the scalability of global
reclaim.
- David Hildenbrand has added some userfaultfd cleanup work in the
series "mm: uffd-wp + change_protection() cleanups".
- Christoph Hellwig has removed the generic_writepages() library
function in the series "remove generic_writepages".
- Baolin Wang has performed some maintenance on the compaction code in
his series "Some small improvements for compaction".
- Sidhartha Kumar is doing some maintenance work on struct page in his
series "Get rid of tail page fields".
- David Hildenbrand contributed some cleanup, bugfixing and
generalization of pte management and of pte debugging in his series
"mm: support __HAVE_ARCH_PTE_SWP_EXCLUSIVE on all architectures with
swap PTEs".
- Mel Gorman and Neil Brown have removed the __GFP_ATOMIC allocation
flag in the series "Discard __GFP_ATOMIC".
- Sergey Senozhatsky has improved zsmalloc's memory utilization with
his series "zsmalloc: make zspage chain size configurable".
- Joey Gouly has added prctl() support for prohibiting the creation of
writeable+executable mappings.
The previous BPF-based approach had shortcomings. See "mm: In-kernel
support for memory-deny-write-execute (MDWE)".
- Waiman Long did some kmemleak cleanup and bugfixing in the series
"mm/kmemleak: Simplify kmemleak_cond_resched() & fix UAF".
- T.J. Alumbaugh has contributed some MGLRU cleanup work in his series
"mm: multi-gen LRU: improve".
- Jiaqi Yan has provided some enhancements to our memory error
statistics reporting, mainly by presenting the statistics on a
per-node basis. See the series "Introduce per NUMA node memory error
statistics".
- Mel Gorman has a second and hopefully final shot at fixing a CPU-hog
regression in compaction via his series "Fix excessive CPU usage
during compaction".
- Christoph Hellwig does some vmalloc maintenance work in the series
"cleanup vfree and vunmap".
- Christoph Hellwig has removed block_device_operations.rw_page() in
ths series "remove ->rw_page".
- We get some maple_tree improvements and cleanups in Liam Howlett's
series "VMA tree type safety and remove __vma_adjust()".
- Suren Baghdasaryan has done some work on the maintainability of our
vm_flags handling in the series "introduce vm_flags modifier
functions".
- Some pagemap cleanup and generalization work in Mike Rapoport's
series "mm, arch: add generic implementation of pfn_valid() for
FLATMEM" and "fixups for generic implementation of pfn_valid()"
- Baoquan He has done some work to make /proc/vmallocinfo and
/proc/kcore better represent the real state of things in his series
"mm/vmalloc.c: allow vread() to read out vm_map_ram areas".
- Jason Gunthorpe rationalized the GUP system's interface to the rest
of the kernel in the series "Simplify the external interface for
GUP".
- SeongJae Park wishes to migrate people from DAMON's debugfs interface
over to its sysfs interface. To support this, we'll temporarily be
printing warnings when people use the debugfs interface. See the
series "mm/damon: deprecate DAMON debugfs interface".
- Andrey Konovalov provided the accurately named "lib/stackdepot: fixes
and clean-ups" series.
- Huang Ying has provided a dramatic reduction in migration's TLB flush
IPI rates with the series "migrate_pages(): batch TLB flushing".
- Arnd Bergmann has some objtool fixups in "objtool warning fixes".
* tag 'mm-stable-2023-02-20-13-37' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (505 commits)
include/linux/migrate.h: remove unneeded externs
mm/memory_hotplug: cleanup return value handing in do_migrate_range()
mm/uffd: fix comment in handling pte markers
mm: change to return bool for isolate_movable_page()
mm: hugetlb: change to return bool for isolate_hugetlb()
mm: change to return bool for isolate_lru_page()
mm: change to return bool for folio_isolate_lru()
objtool: add UACCESS exceptions for __tsan_volatile_read/write
kmsan: disable ftrace in kmsan core code
kasan: mark addr_has_metadata __always_inline
mm: memcontrol: rename memcg_kmem_enabled()
sh: initialize max_mapnr
m68k/nommu: add missing definition of ARCH_PFN_OFFSET
mm: percpu: fix incorrect size in pcpu_obj_full_size()
maple_tree: reduce stack usage with gcc-9 and earlier
mm: page_alloc: call panic() when memoryless node allocation fails
mm: multi-gen LRU: avoid futile retries
migrate_pages: move THP/hugetlb migration support check to simplify code
migrate_pages: batch flushing TLB
migrate_pages: share more code between _unmap and _move
...
In loop_set_status_from_info(), lo->lo_offset and lo->lo_sizelimit should
be checked before reassignment, because if an overflow error occurs, the
original correct value will be changed to the wrong value, and it will not
be changed back.
More, the original patch did not solve the problem, the value was set and
ioctl returned an error, but the subsequent io used the value in the loop
driver, which still caused an alarm:
loop_handle_cmd
do_req_filebacked
loff_t pos = ((loff_t) blk_rq_pos(rq) << 9) + lo->lo_offset;
lo_rw_aio
cmd->iocb.ki_pos = pos
Fixes: c490a0b5a4 ("loop: Check for overflow while configuring loop")
Signed-off-by: Zhong Jinghua <zhongjinghua@huawei.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20230221095027.3656193-1-zhongjinghua@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Small cleanup of the pata_octeon driver to drop a useless platform
callback, from Uwe.
* Simplify ata_scsi_cmd_error_handler() code using the fact that
ap->ops->error_handler is NULL most of the time, from Wenchao.
* Several patches improving libata error handling. This is in
preparation for supporting the command duration limits (CDL)
feature. The changes allow handling corner cases of ATA NCQ errors
which do not happen with regular drives but will be triggered with
CDL drives. From Niklas.
* Simplify the qc_fill_rtf operation, from me.
* Improve SCSI command translation for the
REPORT_SUPPORTED_OPERATION_CODES command, from me.
* Cleanup of libata FUA handling. This falls short of enabling FUA for
ATA drives that support it by default as there were concerns that
old drives would break. The series howeverfixes several issues with
the FUA support to ensure that FUA is reported as being supported
only for drives that can handle all possible write cases (NCQ and
non-NCQ). A check in the block layer is also added to ensure that we
never see read FUA commands (current behavior). From me.
* Several patches to move the old PARIDE (parallel port IDE) driver to
libata as pata_parport. Given that this driver also needs protocol
modules, the driver code resides in its own pata_parport directoy
under drivers/ata. From Ondrej.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCY/VTnQAKCRDdoc3SxdoY
dk77AQCA1frczKhcOFe2PK/FsFAiO9Nlx/snk7V95JdjVG8GlwEAkey7mvbXMfX0
fDbqpaCkWFb6SvwxdMSATlqUvwEpSQ8=
=tqQP
-----END PGP SIGNATURE-----
Merge tag 'ata-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA updates from Damien Le Moal:
- Small cleanup of the pata_octeon driver to drop a useless platform
callback (Uwe)
- Simplify ata_scsi_cmd_error_handler() code using the fact that
ap->ops->error_handler is NULL most of the time (Wenchao)
- Several patches improving libata error handling. This is in
preparation for supporting the command duration limits (CDL) feature.
The changes allow handling corner cases of ATA NCQ errors which do
not happen with regular drives but will be triggered with CDL drives
(Niklas)
- Simplify the qc_fill_rtf operation (me)
- Improve SCSI command translation for REPORT_SUPPORTED_OPERATION_CODES
command (me)
- Cleanup of libata FUA handling.
This falls short of enabling FUA for ATA drives that support it by
default as there were concerns that old drives would break. The
series however fixes several issues with the FUA support to ensure
that FUA is reported as being supported only for drives that can
handle all possible write cases (NCQ and non-NCQ). A check in the
block layer is also added to ensure that we never see read FUA
commands (current behavior) (me)
- Several patches to move the old PARIDE (parallel port IDE) driver to
libata as pata_parport. Given that this driver also needs protocol
modules, the driver code resides in its own pata_parport directoy
under drivers/ata (Ondrej)
* tag 'ata-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: pata_parport: Fix ida_alloc return value error check
drivers/block: Move PARIDE protocol modules to drivers/ata/pata_parport
drivers/block: Remove PARIDE core and high-level protocols
ata: pata_parport: add driver (PARIDE replacement)
ata: libata: exclude FUA support for known buggy drives
ata: libata: Fix FUA handling in ata_build_rw_tf()
ata: libata: cleanup fua support detection
ata: libata: Rename and cleanup ata_rwcmd_protocol()
ata: libata: Introduce ata_ncq_supported()
block: add a sanity check for non-write flush/fua bios
ata: libata-scsi: improve ata_scsiop_maint_in()
ata: libata-scsi: do not overwrite SCSI ML and status bytes
ata: libata: move NCQ related ATA_DFLAGs
ata: libata: respect successfully completed commands during errors
ata: libata: read the shared status for successful NCQ commands once
ata: libata: simplify qc_fill_rtf port operation interface
ata: scsi: rename flag ATA_QCFLAG_FAILED to ATA_QCFLAG_EH
ata: libata-eh: Cleanup ata_scsi_cmd_error_handler()
ata: octeon: Drop empty platform remove function
sizeof(struct ublksrv_io_cmd) is 16bytes, which can be held in 64byte SQE,
so not necessary to check IO_URING_F_SQE128.
With this change, we get chance to save half SQ ring memory.
Fixed: 71f28f3136 ("ublk_drv: add io_uring based userspace block driver")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230220041413.1524335-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch adds completion batching to the IRQ path. It reuses batch
completion code of virtblk_poll(). It collects requests to io_comp_batch
and processes them all at once. It can boost up the performance by 2%.
To validate the performance improvement and stabilty, I did fio test with
4 vCPU VM and 12 vCPU VM respectively. Both VMs have 8GB ram and the same
number of HW queues as vCPU.
The fio cammad is as follows and I ran the fio 5 times and got IOPS average.
(io_uring, randread, direct=1, bs=512, iodepth=64 numjobs=2,4)
Test result shows about 2% improvement.
4 vcpu VM | numjobs=2 | numjobs=4
-----------------------------------------------------------
fio without patch | 367.2K IOPS | 397.6K IOPS
-----------------------------------------------------------
fio with patch | 372.8K IOPS | 407.7K IOPS
12 vcpu VM | numjobs=2 | numjobs=4
-----------------------------------------------------------
fio without patch | 363.6K IOPS | 374.8K IOPS
-----------------------------------------------------------
fio with patch | 373.8K IOPS | 385.3K IOPS
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Message-Id: <20221221145456.281218-3-suwan.kim027@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Driver should set req->state to MQ_RQ_COMPLETE after it finishes to process
req. But virtio-blk doesn't set MQ_RQ_COMPLETE after virtblk_poll() handles
req and req->state still remains MQ_RQ_IN_FLIGHT. Fortunately so far there
is no issue about it because blk_mq_end_request_batch() sets req->state to
MQ_RQ_IDLE.
In this patch, virblk_poll() calls blk_mq_complete_request_remote() to set
req->state to MQ_RQ_COMPLETE before it adds req to a batch completion list.
So it properly sets req->state after polling I/O is finished.
Fixes: 4e04005256 ("virtio-blk: support polling I/O")
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Message-Id: <20221221145456.281218-2-suwan.kim027@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----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=poRc
-----END PGP SIGNATURE-----
Merge tag 'for-6.3/block-2023-02-16' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe updates via Christoph:
- Small improvements to the logging functionality (Amit Engel)
- Authentication cleanups (Hannes Reinecke)
- Cleanup and optimize the DMA mapping cod in the PCIe driver
(Keith Busch)
- Work around the command effects for Format NVM (Keith Busch)
- Misc cleanups (Keith Busch, Christoph Hellwig)
- Fix and cleanup freeing single sgl (Keith Busch)
- MD updates via Song:
- Fix a rare crash during the takeover process
- Don't update recovery_cp when curr_resync is ACTIVE
- Free writes_pending in md_stop
- Change active_io to percpu
- Updates to drbd, inching us closer to unifying the out-of-tree driver
with the in-tree one (Andreas, Christoph, Lars, Robert)
- BFQ update adding support for multi-actuator drives (Paolo, Federico,
Davide)
- Make brd compliant with REQ_NOWAIT (me)
- Fix for IOPOLL and queue entering, fixing stalled IO waiting on
timeouts (me)
- Fix for REQ_NOWAIT with multiple bios (me)
- Fix memory leak in blktrace cleanup (Greg)
- Clean up sbitmap and fix a potential hang (Kemeng)
- Clean up some bits in BFQ, and fix a bug in the request injection
(Kemeng)
- Clean up the request allocation and issue code, and fix some bugs
related to that (Kemeng)
- ublk updates and fixes:
- Add support for unprivileged ublk (Ming)
- Improve device deletion handling (Ming)
- Misc (Liu, Ziyang)
- s390 dasd fixes (Alexander, Qiheng)
- Improve utility of request caching and fixes (Anuj, Xiao)
- zoned cleanups (Pankaj)
- More constification for kobjs (Thomas)
- blk-iocost cleanups (Yu)
- Remove bio splitting from drivers that don't need it (Christoph)
- Switch blk-cgroups to use struct gendisk. Some of this is now
incomplete as select late reverts were done. (Christoph)
- Add bvec initialization helpers, and convert callers to use that
rather than open-coding it (Christoph)
- Misc fixes and cleanups (Jinke, Keith, Arnd, Bart, Li, Martin,
Matthew, Ulf, Zhong)
* tag 'for-6.3/block-2023-02-16' of git://git.kernel.dk/linux: (169 commits)
brd: use radix_tree_maybe_preload instead of radix_tree_preload
block: use proper return value from bio_failfast()
block: bio-integrity: Copy flags when bio_integrity_payload is cloned
block: Fix io statistics for cgroup in throttle path
brd: mark as nowait compatible
brd: check for REQ_NOWAIT and set correct page allocation mask
brd: return 0/-error from brd_insert_page()
block: sync mixed merged request's failfast with 1st bio's
Revert "blk-cgroup: pin the gendisk in struct blkcg_gq"
Revert "blk-cgroup: pass a gendisk to blkg_lookup"
Revert "blk-cgroup: delay blk-cgroup initialization until add_disk"
Revert "blk-cgroup: delay calling blkcg_exit_disk until disk_release"
Revert "blk-cgroup: move the cgroup information to struct gendisk"
nvme-pci: remove iod use_sgls
nvme-pci: fix freeing single sgl
block: ublk: check IO buffer based on flag need_get_data
s390/dasd: Fix potential memleak in dasd_eckd_init()
s390/dasd: sort out physical vs virtual pointers usage
block: Remove the ALLOC_CACHE_SLACK constant
block: make kobj_type structures constant
...
Unconditionally calling radix_tree_preload_end() results in a OOPS
message as the preload is only conditionally called for
gfpflags_allow_blocking().
[ 20.267323] BUG: using smp_processor_id() in preemptible [00000000] code: fio/416
[ 20.267837] caller is brd_insert_page.part.0+0xbe/0x190 [brd]
[ 20.269436] Call Trace:
[ 20.269598] <TASK>
[ 20.269742] dump_stack_lvl+0x32/0x50
[ 20.269982] check_preemption_disabled+0xd1/0xe0
[ 20.270289] brd_insert_page.part.0+0xbe/0x190 [brd]
[ 20.270664] brd_submit_bio+0x33f/0xf40 [brd]
Use radix_tree_maybe_preload() which does preload only if
gfpflags_allow_blocking() is true but also takes the lock. Therefore,
unconditionally calling radix_tree_preload_end() should not create any
issues and the message disappears.
Fixes: 6ded703c56 ("brd: check for REQ_NOWAIT and set correct page allocation mask")
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Link: https://lore.kernel.org/r/20230217121442.33914-1-p.raghav@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
By default, non-mq drivers do not support nowait. This causes io_uring
to use a slower path as the driver cannot be trust not to block. brd
can safely set the nowait flag, as worst case all it does is a NOIO
allocation.
For io_uring, this makes a substantial difference. Before:
submitter=0, tid=453, file=/dev/ram0, node=-1
polled=0, fixedbufs=1/0, register_files=1, buffered=0, QD=128
Engine=io_uring, sq_ring=128, cq_ring=128
IOPS=440.03K, BW=1718MiB/s, IOS/call=32/31
IOPS=428.96K, BW=1675MiB/s, IOS/call=32/32
IOPS=442.59K, BW=1728MiB/s, IOS/call=32/31
IOPS=419.65K, BW=1639MiB/s, IOS/call=32/32
IOPS=426.82K, BW=1667MiB/s, IOS/call=32/31
and after:
submitter=0, tid=354, file=/dev/ram0, node=-1
polled=0, fixedbufs=1/0, register_files=1, buffered=0, QD=128
Engine=io_uring, sq_ring=128, cq_ring=128
IOPS=3.37M, BW=13.15GiB/s, IOS/call=32/31
IOPS=3.45M, BW=13.46GiB/s, IOS/call=32/31
IOPS=3.43M, BW=13.42GiB/s, IOS/call=32/32
IOPS=3.43M, BW=13.39GiB/s, IOS/call=32/31
IOPS=3.43M, BW=13.38GiB/s, IOS/call=32/31
or about an 8x in difference. Now that brd is prepared to deal with
REQ_NOWAIT reads/writes, mark it as supporting that.
Cc: stable@vger.kernel.org # 5.10+
Link: https://lore.kernel.org/linux-block/20230203103005.31290-1-p.raghav@samsung.com/
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If REQ_NOWAIT is set, then do a non-blocking allocation if the operation
is a write and we need to insert a new page. Currently REQ_NOWAIT cannot
be set as the queue isn't marked as supporting nowait, this change is in
preparation for allowing that.
radix_tree_preload() warns on attempting to call it with an allocation
mask that doesn't allow blocking. While that warning could arguably
be removed, we need to handle radix insertion failures anyway as they
are more likely if we cannot block to get memory.
Remove legacy BUG_ON()'s and turn them into proper errors instead, one
for the allocation failure and one for finding a page that doesn't
match the correct index.
Cc: stable@vger.kernel.org # 5.10+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It currently returns a page, but callers just check for NULL/page to
gauge success. Clean this up and return the appropriate error directly
instead.
Cc: stable@vger.kernel.org # 5.10+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
virtio blk returns a 64 bit append_sector in an input buffer,
in LE format. This field is not tagged as LE correctly, so
even though the generated code is ok, we get warnings from sparse:
drivers/block/virtio_blk.c:332:33: sparse: sparse: cast to restricted __le64
Make sparse happy by using the correct type.
Message-Id: <20221220125154.564265-1-mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtblk_result returns blk_status_t which is a bitwise restricted type,
so we are not supposed to stuff it in a plain int temporary variable.
All we do with it is pass it on to a function expecting blk_status_t so
the generated code is ok, but we get warnings from sparse:
drivers/block/virtio_blk.c:326:36: sparse: sparse: incorrect type in initializer (different base types) @@ expected int status @@
+got restricted blk_status_t @@
drivers/block/virtio_blk.c:334:33: sparse: sparse: incorrect type in argument 2 (different base types) @@ expected restricted
+blk_status_t [usertype] error @@ got int status @@
Make sparse happy by using the correct type.
Message-Id: <20221220124152.523531-1-mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
This patch adds support for Zoned Block Devices (ZBDs) to the kernel
virtio-blk driver.
The patch accompanies the virtio-blk ZBD support draft that is now
being proposed for standardization. The latest version of the draft is
linked at
https://github.com/oasis-tcs/virtio-spec/issues/143 .
The QEMU zoned device code that implements these protocol extensions
has been developed by Sam Li and it is currently in review at the QEMU
mailing list.
A number of virtblk request structure changes has been introduced to
accommodate the functionality that is specific to zoned block devices
and, most importantly, make room for carrying the Zoned Append sector
value from the device back to the driver along with the request status.
The zone-specific code in the patch is heavily influenced by NVMe ZNS
code in drivers/nvme/host/zns.c, but it is simpler because the proposed
virtio ZBD draft only covers the zoned device features that are
relevant to the zoned functionality provided by Linux block layer.
includes the following fixup:
virtio-blk: fix probe without CONFIG_BLK_DEV_ZONED
When building without CONFIG_BLK_DEV_ZONED, VIRTIO_BLK_F_ZONED
is excluded from array of driver features.
As a result virtio_has_feature panics in virtio_check_driver_offered_feature
since that by design verifies that a feature we are checking for
is listed in the feature array.
To fix, replace the call to virtio_has_feature with a stub.
Message-Id: <20221016034127.330942-3-dmitry.fomichev@wdc.com>
Co-developed-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20221220112340.518841-1-mst@redhat.com>
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Reported-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Debugged-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Currently, uring_cmd with UBLK_IO_FETCH_REQ or
UBLK_IO_COMMIT_AND_FETCH_REQ is always checked whether
userspace server has provided IO buffer even flag
UBLK_F_NEED_GET_DATA is configured.
This is a excessive check. If UBLK_F_NEED_GET_DATA is
configured, FETCH_RQ doesn't need to provide IO buffer;
COMMIT_AND_FETCH_REQ also doesn't need to do that if
the IO type is not READ.
Check ub_cmd->addr together with ublk_need_get_data()
and IO type in ublk_ch_uring_cmd().
With this fix, userspace server doesn't need to preserve
buffers for every ublk_io when flag UBLK_F_NEED_GET_DATA
is configured, in order to save memory.
Signed-off-by: Liu Xiaodong <xiaodong.liu@intel.com>
Fixes: c86019ff75 ("ublk_drv: add support for UBLK_IO_NEED_GET_DATA")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230210141356.112321-1-xiaodong.liu@intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Inside ublk_ctrl_del_dev(), when the device is removed, we wait
until the device number is freed with holding global lock of
ublk_ctl_mutex, this way isn't friendly from user viewpoint:
1) if device is in-use, the current delete command hangs in
ublk_ctrl_del_dev(), and user can't break from the handling
because wait_event() is used
2) global lock is held, so any new device can't be added and
other old devices can't be removed.
Improve the deleting handling by the following way, suggested by
Nadav:
1) wait without holding the global lock
2) replace wait_event() with wait_event_interruptible()
Reported-by: Nadav Amit <nadav.amit@gmail.com>
Suggested-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230207150700.545530-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
queuedata is not referenced in ublk_drv and we can use driver_data
instead. Pass NULL to blk_mq_alloc_disk() as queuedata while allocating
ublk's gendisk.
Signed-off-by: Ziyang Zhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230207070839.370817-4-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
WRITE_ZEROES won't return bytes returned just like FLUSH and DISCARD,
and we can end it directly. Add missing comment for it in
ublk_complete_rq().
Signed-off-by: Ziyang Zhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230207070839.370817-3-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio_has_data() allows a NULL bio so the NULL check in
ublk_rq_has_data() is unnecessary.
Signed-off-by: Ziyang Zhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230207070839.370817-2-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=/+rE
-----END PGP SIGNATURE-----
Merge tag 'block-6.2-2023-02-03' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
"A bit bigger than I'd like at this point, but mostly a bunch of little
fixes. In detail:
- NVMe pull request via Christoph:
- Fix a missing queue put in nvmet_fc_ls_create_association
(Amit Engel)
- Clear queue pointers on tag_set initialization failure
(Maurizio Lombardi)
- Use workqueue dedicated to authentication (Shin'ichiro
Kawasaki)
- Fix for an overflow in ublk (Liu)
- Fix for leaking a queue reference in block cgroups (Ming)
- Fix for a use-after-free in BFQ (Yu)"
* tag 'block-6.2-2023-02-03' of git://git.kernel.dk/linux:
blk-cgroup: don't update io stat for root cgroup
nvme-auth: use workqueue dedicated to authentication
nvme: clear the request_queue pointers on failure in nvme_alloc_io_tag_set
nvme: clear the request_queue pointers on failure in nvme_alloc_admin_tag_set
nvme-fc: fix a missing queue put in nvmet_fc_ls_create_association
block: Fix the blk_mq_destroy_queue() documentation
block: ublk: extending queue_size to fix overflow
block, bfq: fix uaf for bfqq in bic_set_bfqq()
Use the bvec_set_page helper to initialize bvecs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20230203150634.3199647-11-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use the bvec_set_virt helper to initialize the special_vec.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20230203150634.3199647-10-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use the bvec_set_page helper to initialize the copy up bvec.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Link: https://lore.kernel.org/r/20230203150634.3199647-9-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The ->rw_page method is a special purpose bypass of the usual bio handling
path that is limited to single-page reads and writes and synchronous which
causes a lot of extra code in the drivers, callers and the block layer.
The only remaining user is the MM swap code. Switch that swap code to
simply submit a single-vec on-stack bio an synchronously wait on it based
on a newly added QUEUE_FLAG_SYNCHRONOUS flag set by the drivers that
currently implement ->rw_page instead. While this touches one extra cache
line and executes extra code, it simplifies the block layer and drivers
and ensures that all feastures are properly supported by all drivers, e.g.
right now ->rw_page bypassed cgroup writeback entirely.
[akpm@linux-foundation.org: fix comment typo, per Dan]
Link: https://lkml.kernel.org/r/20230125133436.447864-8-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Make the following minor changes which were reported by colleagues
while reviewing this code:
- Remove the parentheses from around the LOOP_DEFAULT_HW_Q_DEPTH
definition since these are superfluous.
- Accept other number formats than decimal, e.g. hexadecimal.
- Do not set hw_queue_depth to an out-of-range value, even if that value
won't be used.
- Use the LOOP_DEFAULT_HW_Q_DEPTH macro in the kernel module parameter
description to prevent that the description gets out of sync.
This patch has been tested as follows:
# modprobe -r loop
# modprobe loop hw_queue_depth=-1
modprobe: ERROR: could not insert 'loop': Invalid argument
# modprobe loop hw_queue_depth=0
modprobe: ERROR: could not insert 'loop': Invalid argument
# modprobe loop hw_queue_depth=1; cat /sys/module/loop/parameters/hw_queue_depth
1
# modprobe -r loop; modprobe loop; cat /sys/module/loop/parameters/hw_queue_depth hw_queue_depth=0x10
16
# modprobe -r loop; modprobe loop; cat /sys/module/loop/parameters/hw_queue_depth hw_queue_depth=128
128
# modprobe -r loop; modprobe loop hw_queue_depth=129; cat /sys/module/loop/parameters/hw_queue_depth
129
# modprobe -r loop; modprobe loop hw_queue_depth=$((1<<32))
modprobe: ERROR: could not insert 'loop': Numerical result out of range
See also commit ef44c50837 ("loop: allow user to set the queue
depth").
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20230130211347.832110-1-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Owner of one unprivileged ublk device could be one evil user, which
can grant this disk's privilege to other users deliberately, and
this way could be like making one trap and waiting for other users
to be caught.
So only owner to open unprivileged disk even though the owner
grants disk privilege to other user. This way is reasonable too
given anyone can create ublk disk, and no need other's grant.
Reported-by: Stefan Hajnoczi <stefanha@redhat.com>
Fixes: 4093cb5a06 ("ublk_drv: add mechanism for supporting unprivileged ublk device")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230131040446.214583-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When validating drafted SPDK ublk target, in a case that
assigning large queue depth to multiqueue ublk device,
ublk target would run into a weird incorrect state. During
rounds of review and debug, An overflow bug was found
in ublk driver.
In ublk_cmd.h, UBLK_MAX_QUEUE_DEPTH is 4096 which means
each ublk queue depth can be set as large as 4096. But
when setting qd for a ublk device,
sizeof(struct ublk_queue) + depth * sizeof(struct ublk_io)
will be larger than 65535 if qd is larger than 2728.
Then queue_size is overflowed, and ublk_get_queue()
references a wrong pointer position. The wrong content of
ublk_queue elements will lead to out-of-bounds memory
access.
Extend queue_size in ublk_device as "unsigned int".
Signed-off-by: Liu Xiaodong <xiaodong.liu@intel.com>
Fixes: 71f28f3136 ("ublk_drv: add io_uring based userspace block driver")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230131070552.115067-1-xiaodong.liu@intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move PARIDE protocol modules out of drivers/block into
drivers/ata/pata_parport and update the CONFIG_ symbol names to
PATA_PARPORT.
[Damien]
The pata_parport driver file itsef is also moved together with the
protocol modules in drivers/ata/pata_parport.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Remove PARIDE core and high level protocols, taking care not to break
low-level drivers (used by pata_parport). Also update documentation.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The pata_parport is a libata-based replacement of the old PARIDE
subsystem - driver for parallel port IDE devices.
It uses the original paride low-level protocol drivers but does not
need the high-level drivers (pd, pcd, pf, pt, pg). The IDE devices
behind parallel port adapters are handled by the ATA layer.
This will allow paride and its high-level drivers to be removed.
Unfortunately, libata drivers cannot sleep so pata_parport claims
parport before activating the ata host and keeps it claimed (and
protocol connected) until the ata host is removed. This means that
no devices can be chained (neither other pata_parport devices nor
a printer).
paride and pata_parport are mutually exclusive because the compiled
protocol drivers are incompatible.
Tested with:
- Imation SuperDisk LS-120 and HP C4381A (EPAT)
- Freecom Parallel CD (FRPW)
- Toshiba Mobile CD-RW 2793008 w/Freecom Parallel Cable rev.903 (FRIQ)
- Backpack CD-RW 222011 and CD-RW 19350 (BPCK6)
The following bugs in low-level protocol drivers were found and will
be fixed later:
Note: EPP-32 mode is buggy in EPAT - and also in all other protocol
drivers - they don't handle non-multiple-of-4 block transfers
correctly. This causes problems with LS-120 drive.
There is also another bug in EPAT: EPP modes don't work unless a 4-bit
or 8-bit mode is used first (probably some initialization missing?).
Once the device is initialized, EPP works until power cycle.
So after device power on, you have to:
echo "parport0 epat 0" >/sys/bus/pata_parport/new_device
echo pata_parport.0 >/sys/bus/pata_parport/delete_device
echo "parport0 epat 4" >/sys/bus/pata_parport/new_device
(autoprobe will initialize correctly as it tries the slowest modes
first but you'll get the broken EPP-32 mode)
Note: EPP modes are buggy in FRPW, only modes 0 and 1 work.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
ps3vram iterates over the bio one segment, that is page aligned and max
page sized chunk, a time. Because of that there is no point in
calling bio_split_to_limits, or explicitly setting the default limits
that are only used by bio_split_to_limits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Geoff Levand <geoff@infradead.org>
Link: https://lore.kernel.org/r/20230123074718.57951-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
unprivileged ublk device is helpful for container use case, such
as: ublk device created in one unprivileged container can be controlled
and accessed by this container only.
Implement this feature by adding flag of UBLK_F_UNPRIVILEGED_DEV, and if
this flag isn't set, any control command has been run from privileged
user. Otherwise, any control command can be sent from any unprivileged
user, but the user has to be permitted to access the ublk char device
to be controlled.
In case of UBLK_F_UNPRIVILEGED_DEV:
1) for command UBLK_CMD_ADD_DEV, it is always allowed, and user needs
to provide owner's uid/gid in this command, so that udev can set correct
ownership for the created ublk device, since the device owner uid/gid
can be queried via command of UBLK_CMD_GET_DEV_INFO.
2) for other control commands, they can only be run successfully if the
current user is allowed to access the specified ublk char device, for
running the permission check, path of the ublk char device has to be
provided by these commands.
Also add one control of command UBLK_CMD_GET_DEV_INFO2 which always
include the char dev path in payload since userspace may not have
knowledge if this device is created in unprivileged mode.
For applying this mechanism, system administrator needs to take
the following policies:
1) chmod 0666 /dev/ublk-control
2) change ownership of ublkcN & ublkbN
- chown owner_uid:owner_gid /dev/ublkcN
- chown owner_uid:owner_gid /dev/ublkbN
Both can be done via one simple udev rule.
Userspace:
https://github.com/ming1/ubdsrv/tree/unprivileged-ublk
'ublk add -t $TYPE --un_privileged=1' is for creating one un-privileged
ublk device if the user is un-privileged.
Link: https://lore.kernel.org/linux-block/YoOr6jBfgVm8GvWg@stefanha-x1.localdomain/
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230106041711.914434-7-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Prepare for supporting unprivileged ublk device by limiting max number
ublk devices added. Otherwise too many ublk devices could be added by
un-trusted user, which can be thought as one DoS.
Reviewed-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230106041711.914434-6-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Userspace side only knows device ID, but the associated path of ublkc* and
ublkb* could be changed by udev, and that depends on userspace's policy, so
add parameter of UBLK_PARAM_TYPE_DEVT for retrieving major/minor of the
ublkc* and ublkb*, then user may figure out major/minor of the ublk disks
he/she owns. With major/minor, it is easy to find the device node path.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230106041711.914434-5-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It is annoying for each control command handler to get/put ublk
device and deal with failure.
Control command handler is simplified a lot by moving
ublk_get_device_from_id into ublk_ctrl_uring_cmd().
Reviewed-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230106041711.914434-4-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If any ubq daemon is unprivileged, the ublk char device is allowed
for unprivileged user actually, and we can't trust the current user,
so not probe partitions.
Fixes: 71f28f3136 ("ublk_drv: add io_uring based userspace block driver")
Reviewed-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230106041711.914434-3-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No one uses 'nr_aborted_queues' any more, so remove it.
Reviewed-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230106041711.914434-2-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Trying to remove an "empty" (just initialized, or "cleared") interval
from the tree, this results in an endless loop.
As we typically protect the tree with a spinlock_irq,
the result is a hung system.
Be nice to error cleanup code paths, ignore removal of empty intervals.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20230113123538.144276-8-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This require_context attribute originated in a proposed sparse patch by
Philipp Reisner back in 2008. Johannes Berg had a different solution to
a similar problem, and that patch "won" in the end; so the require_context
thing never got merged. The whole history can be read at [0].
DRBD kept using these annotations anyway for a while. Nowadays, on a
modern unmodified sparse, they obviously do nothing, and they are hardly
used anymore anyway.
So, just remove the definitions of these macros.
[0] https://www.spinics.net/lists/linux-sparse/msg01150.html
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Reviewed-by: Joel Colledge <joel.colledge@linbit.com>
Link: https://lore.kernel.org/r/20230113123538.144276-6-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To be more similar to what we do in the out-of-tree module and ease the
upstreaming process.
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Reviewed-by: Joel Colledge <joel.colledge@linbit.com>
Link: https://lore.kernel.org/r/20230113123506.144082-4-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To be more similar to what we do in the out-of-tree module and ease the
upstreaming process.
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Reviewed-by: Joel Colledge <joel.colledge@linbit.com>
Link: https://lore.kernel.org/r/20230113123506.144082-2-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is used as an unsigned value, so define it that way to avoid
having to cast it.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20230105205146.3610282-2-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The 'ublk_chr_class' is needed when deleting ublk char devices in
ublk_exit(), so move it after devices(idle) are removed.
Fixes the following warning reported by Harris, James R:
[ 859.178950] sysfs group 'power' not found for kobject 'ublkc0'
[ 859.178962] WARNING: CPU: 3 PID: 1109 at fs/sysfs/group.c:278 sysfs_remove_group+0x9c/0xb0
Reported-by: "Harris, James R" <james.r.harris@intel.com>
Fixes: 71f28f3136 ("ublk_drv: add io_uring based userspace block driver")
Link: https://lore.kernel.org/linux-block/Y9JlFmSgDl3+zy3N@T590/T/#t
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Jim Harris <james.r.harris@intel.com>
Link: https://lore.kernel.org/r/20230126115346.263344-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=L12Q
-----END PGP SIGNATURE-----
Merge tag 'block-6.2-2023-01-20' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
"Various little tweaks all over the place:
- NVMe pull request via Christoph:
- fix controller shutdown regression in nvme-apple (Janne Grunau)
- fix a polling on timeout regression in nvme-pci (Keith Busch)
- Fix a bug in the read request side request allocation caching
(Pavel)
- pktcdvd was brought back after we configured a NULL return on bio
splits, make it consistent with the others (me)
- BFQ refcount fix (Yu)
- Block cgroup policy activation fix (Yu)
- Fix for an md regression introduced in the 6.2 cycle (Adrian)"
* tag 'block-6.2-2023-01-20' of git://git.kernel.dk/linux:
nvme-pci: fix timeout request state check
nvme-apple: only reset the controller when RTKit is running
nvme-apple: reset controller during shutdown
block: fix hctx checks for batch allocation
block/rnbd-clt: fix wrong max ID in ida_alloc_max
blk-cgroup: fix missing pd_online_fn() while activating policy
pktcdvd: check for NULL returna fter calling bio_split_to_limits()
block, bfq: switch 'bfqg->ref' to use atomic refcount apis
md: fix incorrect declaration about claim_rdev in md_import_device
When supplied buffer does not have assignment sign next_arg() sets `val`
pointer to NULL, so we cannot dereference it. Add a NULL pointer test to
handle `param` case, in addition to `*val` test, which handles cases when
param has no value assigned to it: `param=`.
Link: https://lkml.kernel.org/r/20230103030119.1496358-1-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
- The double `range` is duplicated in comment, remove one.
- change `syfs` to `sysfs`
Link: https://lkml.kernel.org/r/20221223040331.4194-1-jhs2.lee@samsung.com
Signed-off-by: JeongHyeon Lee <jhs2.lee@samsung.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We need to pass 'end - 1' to ida_alloc_max after switch from
ida_simple_get to ida_alloc_max.
Otherwise smatch warns.
drivers/block/rnbd/rnbd-clt.c:1460 init_dev() error: Calling ida_alloc_max() with a 'max' argument which is a power of 2. -1 missing?
Fixes: 24afc15dbe ("block/rnbd: Remove a useless mutex")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20221230010926.32243-1-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The revert of the removal of this driver happened after we fixed up
the split limits for NOWAIT issue, hence it got missed. Ensure that
we check for a NULL bio after splitting, in case it should be retried.
Marking this as fixing both commits, so that stable backport will do
this correctly.
Cc: stable@vger.kernel.org
Fixes: 9cea62b2cb ("block: don't allow splitting of a REQ_NOWAIT bio")
Fixes: 4b83e99ee7 ("Revert "pktcdvd: remove driver."")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCY76ohgAKCRCAXGG7T9hj
vo8fAP0XJ94B7asqcN4W3EyeyfqxUf1eZvmWRhrbKqpLnmHLaQEA/uJBkXL49Zj7
TTcbxR1coJ/hPwhtmONU4TNtCZ+RXw0=
=2Ib5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- two cleanup patches
- a fix of a memory leak in the Xen pvfront driver
- a fix of a locking issue in the Xen hypervisor console driver
* tag 'for-linus-6.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvcalls: free active map buffer on pvcalls_front_free_map
hvc/xen: lock console list traversal
x86/xen: Remove the unused function p2m_index()
xen: make remove callback of xen driver void returned
-----BEGIN PGP SIGNATURE-----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=LJ5Q
-----END PGP SIGNATURE-----
Merge tag 'block-2023-01-06' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
"The big change here is obviously the revert of the pktcdvd driver
removal. Outside of that, just minor tweaks. In detail:
- Re-instate the pktcdvd driver, which necessitates adding back
bio_copy_data_iter() and the fops->devnode() hook for now (me)
- Fix for splitting of a bio marked as NOWAIT, causing either nowait
reads or writes to error with EAGAIN even if parts of the IO
completed (me)
- Fix for ublk, punting management commands to io-wq as they can all
easily block for extended periods of time (Ming)
- Removal of SRCU dependency for the block layer (Paul)"
* tag 'block-2023-01-06' of git://git.kernel.dk/linux:
block: Remove "select SRCU"
Revert "pktcdvd: remove driver."
Revert "block: remove devnode callback from struct block_device_operations"
Revert "block: bio_copy_data_iter"
ublk: honor IO_URING_F_NONBLOCK for handling control command
block: don't allow splitting of a REQ_NOWAIT bio
block: handle bio_split_to_limits() NULL return
This reverts commit f40eb99897.
There are apparently still users out there of this driver. While we'd
love to remove it to ease the maintenance burden, let's reinstate it
for now until better (userspace) solutions can be developed.
Link: https://lore.kernel.org/lkml/20230104190115.ceglfefco475ev6c@pali/
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Most of control command handlers may sleep, so return -EAGAIN in case
of IO_URING_F_NONBLOCK to defer the handling into io wq context.
Fixes: 71f28f3136 ("ublk_drv: add io_uring based userspace block driver")
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230104133235.836536-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This can't happen right now, but in preparation for allowing
bio_split_to_limits() returning NULL if it ended the bio, check for it
in all the callers.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The virtblk_map_data() function returns negative error codes, however, the
'nents' field of vbr->sg_table is an unsigned int, which causes the error
handling not to work correctly.
Cc: stable@vger.kernel.org
Fixes: 0e9911fa76 ("virtio-blk: support mq_ops->queue_rqs()")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Message-Id: <20221021204126.927603-1-rafaelmendsr@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Suwan Kim <suwan.kim027@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
We use UINT_MAX to limit max_discard_sectors in virtblk_probe,
we can use UINT_MAX to limit max_hw_sectors for consistencies.
No functional change intended.
Signed-off-by: Angus Chen <angus.chen@jaguarmicro.com>
Message-Id: <20221110030124.1986-1-angus.chen@jaguarmicro.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Define a new helper function, virtblk_fail_to_queue(), to
clean up the error handling code in virtio_queue_rq().
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20221016034127.330942-2-dmitry.fomichev@wdc.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=TSec
-----END PGP SIGNATURE-----
Merge tag 'block-6.2-2022-12-19' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- Various fixes for BFQ (Yu, Yuwei)
- Fix for loop command line parsing (Isaac)
- No need to specifically clear REQ_ALLOC_CACHE on IOPOLL downgrade
anymore (me)
- blk-iocost enum fix for newer gcc (Jiri)
- UAF fix for queue release (Ming)
- blk-iolatency error handling memory leak fix (Tejun)
* tag 'block-6.2-2022-12-19' of git://git.kernel.dk/linux:
block: don't clear REQ_ALLOC_CACHE for non-polled requests
block: fix use-after-free of q->q_usage_counter
block, bfq: only do counting of pending-request for BFQ_GROUP_IOSCHED
blk-iolatency: Fix memory leak on add_disk() failures
loop: Fix the max_loop commandline argument treatment when it is set to 0
block/blk-iocost (gcc13): keep large values in a new enum
block, bfq: replace 0/1 with false/true in bic apis
block, bfq: don't return bfqg from __bfq_bic_change_cgroup()
block, bfq: fix possible uaf for 'bfqq->bic'
Since moving to memalloc_nofs_save/restore, SUNRPC has stopped setting the
GFP_NOIO flag on sk_allocation which the networking system uses to decide
when it is safe to use current->task_frag. The results of this are
unexpected corruption in task_frag when SUNRPC is involved in memory
reclaim.
The corruption can be seen in crashes, but the root cause is often
difficult to ascertain as a crashing machine's stack trace will have no
evidence of being near NFS or SUNRPC code. I believe this problem to
be much more pervasive than reports to the community may indicate.
Fix this by having kernel users of sockets that may corrupt task_frag due
to reclaim set sk_use_task_frag = false. Preemptively correcting this
situation for users that still set sk_allocation allows them to convert to
memalloc_nofs_save/restore without the same unexpected corruptions that are
sure to follow, unlikely to show up in testing, and difficult to bisect.
CC: Philipp Reisner <philipp.reisner@linbit.com>
CC: Lars Ellenberg <lars.ellenberg@linbit.com>
CC: "Christoph Böhmwalder" <christoph.boehmwalder@linbit.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Josef Bacik <josef@toxicpanda.com>
CC: Keith Busch <kbusch@kernel.org>
CC: Christoph Hellwig <hch@lst.de>
CC: Sagi Grimberg <sagi@grimberg.me>
CC: Lee Duncan <lduncan@suse.com>
CC: Chris Leech <cleech@redhat.com>
CC: Mike Christie <michael.christie@oracle.com>
CC: "James E.J. Bottomley" <jejb@linux.ibm.com>
CC: "Martin K. Petersen" <martin.petersen@oracle.com>
CC: Valentina Manea <valentina.manea.m@gmail.com>
CC: Shuah Khan <shuah@kernel.org>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: David Howells <dhowells@redhat.com>
CC: Marc Dionne <marc.dionne@auristor.com>
CC: Steve French <sfrench@samba.org>
CC: Christine Caulfield <ccaulfie@redhat.com>
CC: David Teigland <teigland@redhat.com>
CC: Mark Fasheh <mark@fasheh.com>
CC: Joel Becker <jlbec@evilplan.org>
CC: Joseph Qi <joseph.qi@linux.alibaba.com>
CC: Eric Van Hensbergen <ericvh@gmail.com>
CC: Latchesar Ionkov <lucho@ionkov.net>
CC: Dominique Martinet <asmadeus@codewreck.org>
CC: Ilya Dryomov <idryomov@gmail.com>
CC: Xiubo Li <xiubli@redhat.com>
CC: Chuck Lever <chuck.lever@oracle.com>
CC: Jeff Layton <jlayton@kernel.org>
CC: Trond Myklebust <trond.myklebust@hammerspace.com>
CC: Anna Schumaker <anna@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass in
a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be used
no matter what the const value is. This prevents every subsystem from
having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject, objects
as being "non-mutable". The changes to the kobject and driver core in
this pull request are the result of that, as there are lots of paths
where kobjects and device pointers are not modified at all, so marking
them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object rules.
All of this has been bike-shedded in quite a lot of detail on lkml with
different names and implementations resulting in the tiny version we
have in here, much better than my original proposal. Lots of subsystem
maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with no
problems, OTHER than some merge issues with other trees that should be
obvious when you hit them (block tree deletes a driver that this tree
modifies, iommufd tree modifies code that this tree also touches). If
there are merge problems with these trees, please let me know.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wz3A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yks0ACeKYUlVgCsER8eYW+x18szFa2QTXgAn2h/VhZe
1Fp53boFaQkGBjl8mGF8
=v+FB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass
in a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be
used no matter what the const value is. This prevents every subsystem
from having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject,
objects as being "non-mutable". The changes to the kobject and driver
core in this pull request are the result of that, as there are lots of
paths where kobjects and device pointers are not modified at all, so
marking them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object
rules.
All of this has been bike-shedded in quite a lot of detail on lkml
with different names and implementations resulting in the tiny version
we have in here, much better than my original proposal. Lots of
subsystem maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with
no problems"
* tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (58 commits)
device property: Fix documentation for fwnode_get_next_parent()
firmware_loader: fix up to_fw_sysfs() to preserve const
usb.h: take advantage of container_of_const()
device.h: move kobj_to_dev() to use container_of_const()
container_of: add container_of_const() that preserves const-ness of the pointer
driver core: fix up missed drivers/s390/char/hmcdrv_dev.c class.devnode() conversion.
driver core: fix up missed scsi/cxlflash class.devnode() conversion.
driver core: fix up some missing class.devnode() conversions.
driver core: make struct class.devnode() take a const *
driver core: make struct class.dev_uevent() take a const *
cacheinfo: Remove of_node_put() for fw_token
device property: Add a blank line in Kconfig of tests
device property: Rename goto label to be more precise
device property: Move PROPERTY_ENTRY_BOOL() a bit down
device property: Get rid of __PROPERTY_ENTRY_ARRAY_EL*SIZE*()
kernfs: fix all kernel-doc warnings and multiple typos
driver core: pass a const * into of_device_uevent()
kobject: kset_uevent_ops: make name() callback take a const *
kobject: kset_uevent_ops: make filter() callback take a const *
kobject: make kobject_namespace take a const *
...
Since commit fc7a6209d5 ("bus: Make remove callback return void")
forces bus_type::remove be void-returned, it doesn't make much sense for
any bus based driver implementing remove callbalk to return non-void to
its caller.
This change is for xen bus based drivers.
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Link: https://lore.kernel.org/r/TYCP286MB23238119AB4DF190997075C9CAE39@TYCP286MB2323.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Juergen Gross <jgross@suse.com>
Currently, the max_loop commandline argument can be used to specify how
many loop block devices are created at init time. If it is not
specified on the commandline, CONFIG_BLK_DEV_LOOP_MIN_COUNT loop block
devices will be created.
The max_loop commandline argument can be used to override the value of
CONFIG_BLK_DEV_LOOP_MIN_COUNT. However, when max_loop is set to 0
through the commandline, the current logic treats it as if it had not
been set, and creates CONFIG_BLK_DEV_LOOP_MIN_COUNT devices anyway.
Fix this by starting max_loop off as set to CONFIG_BLK_DEV_LOOP_MIN_COUNT.
This preserves the intended behavior of creating
CONFIG_BLK_DEV_LOOP_MIN_COUNT loop block devices if the max_loop
commandline parameter is not specified, and allowing max_loop to
be respected for all values, including 0.
This allows environments that can create all of their required loop
block devices on demand to not have to unnecessarily preallocate loop
block devices.
Fixes: 7328508274 ("remove artificial software max_loop limit")
Cc: stable@vger.kernel.org
Cc: Ken Chen <kenchen@google.com>
Signed-off-by: Isaac J. Manjarres <isaacmanjarres@google.com>
Link: https://lore.kernel.org/r/20221208212902.765781-1-isaacmanjarres@google.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
- More userfaultfs work from Peter Xu.
- Several convert-to-folios series from Sidhartha Kumar and Huang Ying.
- Some filemap cleanups from Vishal Moola.
- David Hildenbrand added the ability to selftest anon memory COW handling.
- Some cpuset simplifications from Liu Shixin.
- Addition of vmalloc tracing support by Uladzislau Rezki.
- Some pagecache folioifications and simplifications from Matthew Wilcox.
- A pagemap cleanup from Kefeng Wang: we have VM_ACCESS_FLAGS, so use it.
- Miguel Ojeda contributed some cleanups for our use of the
__no_sanitize_thread__ gcc keyword. This series shold have been in the
non-MM tree, my bad.
- Naoya Horiguchi improved the interaction between memory poisoning and
memory section removal for huge pages.
- DAMON cleanups and tuneups from SeongJae Park
- Tony Luck fixed the handling of COW faults against poisoned pages.
- Peter Xu utilized the PTE marker code for handling swapin errors.
- Hugh Dickins reworked compound page mapcount handling, simplifying it
and making it more efficient.
- Removal of the autonuma savedwrite infrastructure from Nadav Amit and
David Hildenbrand.
- zram support for multiple compression streams from Sergey Senozhatsky.
- David Hildenbrand reworked the GUP code's R/O long-term pinning so
that drivers no longer need to use the FOLL_FORCE workaround which
didn't work very well anyway.
- Mel Gorman altered the page allocator so that local IRQs can remnain
enabled during per-cpu page allocations.
- Vishal Moola removed the try_to_release_page() wrapper.
- Stefan Roesch added some per-BDI sysfs tunables which are used to
prevent network block devices from dirtying excessive amounts of
pagecache.
- David Hildenbrand did some cleanup and repair work on KSM COW
breaking.
- Nhat Pham and Johannes Weiner have implemented writeback in zswap's
zsmalloc backend.
- Brian Foster has fixed a longstanding corner-case oddity in
file[map]_write_and_wait_range().
- sparse-vmemmap changes for MIPS, LoongArch and NIOS2 from Feiyang
Chen.
- Shiyang Ruan has done some work on fsdax, to make its reflink mode
work better under xfstests. Better, but still not perfect.
- Christoph Hellwig has removed the .writepage() method from several
filesystems. They only need .writepages().
- Yosry Ahmed wrote a series which fixes the memcg reclaim target
beancounting.
- David Hildenbrand has fixed some of our MM selftests for 32-bit
machines.
- Many singleton patches, as usual.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCY5j6ZwAKCRDdBJ7gKXxA
jkDYAP9qNeVqp9iuHjZNTqzMXkfmJPsw2kmy2P+VdzYVuQRcJgEAgoV9d7oMq4ml
CodAgiA51qwzId3GRytIo/tfWZSezgA=
=d19R
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2022-12-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- More userfaultfs work from Peter Xu
- Several convert-to-folios series from Sidhartha Kumar and Huang Ying
- Some filemap cleanups from Vishal Moola
- David Hildenbrand added the ability to selftest anon memory COW
handling
- Some cpuset simplifications from Liu Shixin
- Addition of vmalloc tracing support by Uladzislau Rezki
- Some pagecache folioifications and simplifications from Matthew
Wilcox
- A pagemap cleanup from Kefeng Wang: we have VM_ACCESS_FLAGS, so use
it
- Miguel Ojeda contributed some cleanups for our use of the
__no_sanitize_thread__ gcc keyword.
This series should have been in the non-MM tree, my bad
- Naoya Horiguchi improved the interaction between memory poisoning and
memory section removal for huge pages
- DAMON cleanups and tuneups from SeongJae Park
- Tony Luck fixed the handling of COW faults against poisoned pages
- Peter Xu utilized the PTE marker code for handling swapin errors
- Hugh Dickins reworked compound page mapcount handling, simplifying it
and making it more efficient
- Removal of the autonuma savedwrite infrastructure from Nadav Amit and
David Hildenbrand
- zram support for multiple compression streams from Sergey Senozhatsky
- David Hildenbrand reworked the GUP code's R/O long-term pinning so
that drivers no longer need to use the FOLL_FORCE workaround which
didn't work very well anyway
- Mel Gorman altered the page allocator so that local IRQs can remnain
enabled during per-cpu page allocations
- Vishal Moola removed the try_to_release_page() wrapper
- Stefan Roesch added some per-BDI sysfs tunables which are used to
prevent network block devices from dirtying excessive amounts of
pagecache
- David Hildenbrand did some cleanup and repair work on KSM COW
breaking
- Nhat Pham and Johannes Weiner have implemented writeback in zswap's
zsmalloc backend
- Brian Foster has fixed a longstanding corner-case oddity in
file[map]_write_and_wait_range()
- sparse-vmemmap changes for MIPS, LoongArch and NIOS2 from Feiyang
Chen
- Shiyang Ruan has done some work on fsdax, to make its reflink mode
work better under xfstests. Better, but still not perfect
- Christoph Hellwig has removed the .writepage() method from several
filesystems. They only need .writepages()
- Yosry Ahmed wrote a series which fixes the memcg reclaim target
beancounting
- David Hildenbrand has fixed some of our MM selftests for 32-bit
machines
- Many singleton patches, as usual
* tag 'mm-stable-2022-12-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (313 commits)
mm/hugetlb: set head flag before setting compound_order in __prep_compound_gigantic_folio
mm: mmu_gather: allow more than one batch of delayed rmaps
mm: fix typo in struct pglist_data code comment
kmsan: fix memcpy tests
mm: add cond_resched() in swapin_walk_pmd_entry()
mm: do not show fs mm pc for VM_LOCKONFAULT pages
selftests/vm: ksm_functional_tests: fixes for 32bit
selftests/vm: cow: fix compile warning on 32bit
selftests/vm: madv_populate: fix missing MADV_POPULATE_(READ|WRITE) definitions
mm/gup_test: fix PIN_LONGTERM_TEST_READ with highmem
mm,thp,rmap: fix races between updates of subpages_mapcount
mm: memcg: fix swapcached stat accounting
mm: add nodes= arg to memory.reclaim
mm: disable top-tier fallback to reclaim on proactive reclaim
selftests: cgroup: make sure reclaim target memcg is unprotected
selftests: cgroup: refactor proactive reclaim code to reclaim_until()
mm: memcg: fix stale protection of reclaim target memcg
mm/mmap: properly unaccount memory on mas_preallocate() failure
omfs: remove ->writepage
jfs: remove ->writepage
...
-----BEGIN PGP SIGNATURE-----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=k/vv
-----END PGP SIGNATURE-----
Merge tag 'for-6.2/block-2022-12-08' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe pull requests via Christoph:
- Support some passthrough commands without CAP_SYS_ADMIN (Kanchan
Joshi)
- Refactor PCIe probing and reset (Christoph Hellwig)
- Various fabrics authentication fixes and improvements (Sagi
Grimberg)
- Avoid fallback to sequential scan due to transient issues (Uday
Shankar)
- Implement support for the DEAC bit in Write Zeroes (Christoph
Hellwig)
- Allow overriding the IEEE OUI and firmware revision in configfs
for nvmet (Aleksandr Miloserdov)
- Force reconnect when number of queue changes in nvmet (Daniel
Wagner)
- Minor fixes and improvements (Uros Bizjak, Joel Granados, Sagi
Grimberg, Christoph Hellwig, Christophe JAILLET)
- Fix and cleanup nvme-fc req allocation (Chaitanya Kulkarni)
- Use the common tagset helpers in nvme-pci driver (Christoph
Hellwig)
- Cleanup the nvme-pci removal path (Christoph Hellwig)
- Use kstrtobool() instead of strtobool (Christophe JAILLET)
- Allow unprivileged passthrough of Identify Controller (Joel
Granados)
- Support io stats on the mpath device (Sagi Grimberg)
- Minor nvmet cleanup (Sagi Grimberg)
- MD pull requests via Song:
- Code cleanups (Christoph)
- Various fixes
- Floppy pull request from Denis:
- Fix a memory leak in the init error path (Yuan)
- Series fixing some batch wakeup issues with sbitmap (Gabriel)
- Removal of the pktcdvd driver that was deprecated more than 5 years
ago, and subsequent removal of the devnode callback in struct
block_device_operations as no users are now left (Greg)
- Fix for partition read on an exclusively opened bdev (Jan)
- Series of elevator API cleanups (Jinlong, Christoph)
- Series of fixes and cleanups for blk-iocost (Kemeng)
- Series of fixes and cleanups for blk-throttle (Kemeng)
- Series adding concurrent support for sync queues in BFQ (Yu)
- Series bringing drbd a bit closer to the out-of-tree maintained
version (Christian, Joel, Lars, Philipp)
- Misc drbd fixes (Wang)
- blk-wbt fixes and tweaks for enable/disable (Yu)
- Fixes for mq-deadline for zoned devices (Damien)
- Add support for read-only and offline zones for null_blk
(Shin'ichiro)
- Series fixing the delayed holder tracking, as used by DM (Yu,
Christoph)
- Series enabling bio alloc caching for IRQ based IO (Pavel)
- Series enabling userspace peer-to-peer DMA (Logan)
- BFQ waker fixes (Khazhismel)
- Series fixing elevator refcount issues (Christoph, Jinlong)
- Series cleaning up references around queue destruction (Christoph)
- Series doing quiesce by tagset, enabling cleanups in drivers
(Christoph, Chao)
- Series untangling the queue kobject and queue references (Christoph)
- Misc fixes and cleanups (Bart, David, Dawei, Jinlong, Kemeng, Ye,
Yang, Waiman, Shin'ichiro, Randy, Pankaj, Christoph)
* tag 'for-6.2/block-2022-12-08' of git://git.kernel.dk/linux: (247 commits)
blktrace: Fix output non-blktrace event when blk_classic option enabled
block: sed-opal: Don't include <linux/kernel.h>
sed-opal: allow using IOC_OPAL_SAVE for locking too
blk-cgroup: Fix typo in comment
block: remove bio_set_op_attrs
nvmet: don't open-code NVME_NS_ATTR_RO enumeration
nvme-pci: use the tagset alloc/free helpers
nvme: add the Apple shared tag workaround to nvme_alloc_io_tag_set
nvme: only set reserved_tags in nvme_alloc_io_tag_set for fabrics controllers
nvme: consolidate setting the tagset flags
nvme: pass nr_maps explicitly to nvme_alloc_io_tag_set
block: bio_copy_data_iter
nvme-pci: split out a nvme_pci_ctrl_is_dead helper
nvme-pci: return early on ctrl state mismatch in nvme_reset_work
nvme-pci: rename nvme_disable_io_queues
nvme-pci: cleanup nvme_suspend_queue
nvme-pci: remove nvme_pci_disable
nvme-pci: remove nvme_disable_admin_queue
nvme: merge nvme_shutdown_ctrl into nvme_disable_ctrl
nvme: use nvme_wait_ready in nvme_shutdown_ctrl
...
direction misannotations and (hopefully) preventing
more of the same for the future.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
iHQEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCY5ZzQAAKCRBZ7Krx/gZQ
65RZAP4nTkvOn0NZLVFkuGOx8pgJelXAvrteyAuecVL8V6CR4AD40qCVY51PJp8N
MzwiRTeqnGDxTTF7mgd//IB6hoatAA==
=bcvF
-----END PGP SIGNATURE-----
Merge tag 'pull-iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull iov_iter updates from Al Viro:
"iov_iter work; most of that is about getting rid of direction
misannotations and (hopefully) preventing more of the same for the
future"
* tag 'pull-iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
use less confusing names for iov_iter direction initializers
iov_iter: saner checks for attempt to copy to/from iterator
[xen] fix "direction" argument of iov_iter_kvec()
[vhost] fix 'direction' argument of iov_iter_{init,bvec}()
[target] fix iov_iter_bvec() "direction" argument
[s390] memcpy_real(): WRITE is "data source", not destination...
[s390] zcore: WRITE is "data source", not destination...
[infiniband] READ is "data destination", not source...
[fsi] WRITE is "data source", not destination...
[s390] copy_oldmem_kernel() - WRITE is "data source", not destination
csum_and_copy_to_iter(): handle ITER_DISCARD
get rid of unlikely() on page_copy_sane() calls
-----BEGIN PGP SIGNATURE-----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=QRhK
-----END PGP SIGNATURE-----
Merge tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator updates from Jason Donenfeld:
- Replace prandom_u32_max() and various open-coded variants of it,
there is now a new family of functions that uses fast rejection
sampling to choose properly uniformly random numbers within an
interval:
get_random_u32_below(ceil) - [0, ceil)
get_random_u32_above(floor) - (floor, U32_MAX]
get_random_u32_inclusive(floor, ceil) - [floor, ceil]
Coccinelle was used to convert all current users of
prandom_u32_max(), as well as many open-coded patterns, resulting in
improvements throughout the tree.
I'll have a "late" 6.1-rc1 pull for you that removes the now unused
prandom_u32_max() function, just in case any other trees add a new
use case of it that needs to converted. According to linux-next,
there may be two trivial cases of prandom_u32_max() reintroductions
that are fixable with a 's/.../.../'. So I'll have for you a final
conversion patch doing that alongside the removal patch during the
second week.
This is a treewide change that touches many files throughout.
- More consistent use of get_random_canary().
- Updates to comments, documentation, tests, headers, and
simplification in configuration.
- The arch_get_random*_early() abstraction was only used by arm64 and
wasn't entirely useful, so this has been replaced by code that works
in all relevant contexts.
- The kernel will use and manage random seeds in non-volatile EFI
variables, refreshing a variable with a fresh seed when the RNG is
initialized. The RNG GUID namespace is then hidden from efivarfs to
prevent accidental leakage.
These changes are split into random.c infrastructure code used in the
EFI subsystem, in this pull request, and related support inside of
EFISTUB, in Ard's EFI tree. These are co-dependent for full
functionality, but the order of merging doesn't matter.
- Part of the infrastructure added for the EFI support is also used for
an improvement to the way vsprintf initializes its siphash key,
replacing an sleep loop wart.
- The hardware RNG framework now always calls its correct random.c
input function, add_hwgenerator_randomness(), rather than sometimes
going through helpers better suited for other cases.
- The add_latent_entropy() function has long been called from the fork
handler, but is a no-op when the latent entropy gcc plugin isn't
used, which is fine for the purposes of latent entropy.
But it was missing out on the cycle counter that was also being mixed
in beside the latent entropy variable. So now, if the latent entropy
gcc plugin isn't enabled, add_latent_entropy() will expand to a call
to add_device_randomness(NULL, 0), which adds a cycle counter,
without the absent latent entropy variable.
- The RNG is now reseeded from a delayed worker, rather than on demand
when used. Always running from a worker allows it to make use of the
CPU RNG on platforms like S390x, whose instructions are too slow to
do so from interrupts. It also has the effect of adding in new inputs
more frequently with more regularity, amounting to a long term
transcript of random values. Plus, it helps a bit with the upcoming
vDSO implementation (which isn't yet ready for 6.2).
- The jitter entropy algorithm now tries to execute on many different
CPUs, round-robining, in hopes of hitting even more memory latencies
and other unpredictable effects. It also will mix in a cycle counter
when the entropy timer fires, in addition to being mixed in from the
main loop, to account more explicitly for fluctuations in that timer
firing. And the state it touches is now kept within the same cache
line, so that it's assured that the different execution contexts will
cause latencies.
* tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: (23 commits)
random: include <linux/once.h> in the right header
random: align entropy_timer_state to cache line
random: mix in cycle counter when jitter timer fires
random: spread out jitter callback to different CPUs
random: remove extraneous period and add a missing one in comments
efi: random: refresh non-volatile random seed when RNG is initialized
vsprintf: initialize siphash key using notifier
random: add back async readiness notifier
random: reseed in delayed work rather than on-demand
random: always mix cycle counter in add_latent_entropy()
hw_random: use add_hwgenerator_randomness() for early entropy
random: modernize documentation comment on get_random_bytes()
random: adjust comment to account for removed function
random: remove early archrandom abstraction
random: use random.trust_{bootloader,cpu} command line option only
stackprotector: actually use get_random_canary()
stackprotector: move get_random_canary() into stackprotector.h
treewide: use get_random_u32_inclusive() when possible
treewide: use get_random_u32_{above,below}() instead of manual loop
treewide: use get_random_u32_below() instead of deprecated function
...
Way back in 2016 in commit 5a8b187c61 ("pktcdvd: mark as unmaintained
and deprecated") this driver was marked as "will be removed soon". 5
years seems long enough to have it stick around after that, so finally
remove the thing now.
Reported-by: Christoph Hellwig <hch@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Thomas Maier <balagi@justmail.de>
Cc: Peter Osterlund <petero2@telia.com>
Cc: linux-block@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20221202182758.1339039-1-gregkh@linuxfoundation.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In zoned mode, zones with write pointers can have conditions "read-only"
or "offline". In read-only condition, zones can not be written. In
offline condition, the zones can be neither written nor read. These
conditions are intended for zones with media failures, then it is
difficult to set those conditions to zones on real devices.
To test handling of zones in the conditions, add a feature to null_blk
to set up zones in read-only or offline condition. Add new configuration
attributes "zone_readonly" and "zone_offline". Write a sector to the
attribute files to specify the target zone to set the zone conditions.
For example, following command lines do it:
echo 0 > nullb1/zone_readonly
echo 524288 > nullb1/zone_offline
When the specified zones are already in read-only or offline condition,
normal empty condition is restored to the zones. These condition changes
can be done only after the null_blk device get powered, since status
area of each zone is not yet allocated before power-on.
Also improve zone condition checks to inhibit all commands for zones in
offline conditions. In same manner, inhibit write and zone management
commands for zones in read-only condition.
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Link: https://lore.kernel.org/r/20221201061036.2342206-1-shinichiro.kawasaki@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use call site specific ratelimit instead of one single static global.
Also ratelimit ASSERTION messages generated by expect().
Originally-from: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20221201110349.1282687-5-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Incorporate as many out-of-tree changes as possible without changing the
genl API.
Over the years, we restructured this several times, and also changed the
log format.
One breaking change is that DRBD 9 gained "implicit options", like a
connection name. This cannot be replayed here without changing the API,
so save it for later.
Originally-from: Andreas Gruenbacher <agruen@linbit.com>
Originally-from: Philipp Reisner <philipp.reisner@linbit.com>
Originally-from: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20221201110349.1282687-4-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We don't show num_reads and num_writes since we removed corresponding
sysfs nodes in 2017. Block layer stats are exposed via
/sys/block/zramX/stat file.
However, we still increment those atomic vars and store them in zram
stats. Remove leftovers.
Link: https://lkml.kernel.org/r/20221117141326.1105181-1-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Add a new flag to zram block state that shows if the page is
incompressible: that none of the algorithm (including secondary ones)
could compress it.
Link: https://lkml.kernel.org/r/20221109115047.2921851-14-senozhatsky@chromium.org
Suggested-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Alexey Romanov <avromanov@sberdevices.ru>
Cc: Nhat Pham <nphamcs@gmail.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Recompression iterates through all the registered secondary compression
algorithms in order of their priorities so that we have higher chances of
finding the algorithm that compresses a particular page. This, however,
may not always be best approach and sometimes we may want to limit
recompression to only one particular algorithm. For instance, when a
higher priority algorithm uses too much power and device has a relatively
low battery level we may want to limit recompression to use only a lower
priority algorithm, which uses less power.
Introduce algo= parameter support to recompression sysfs knob so that
user-sapce can request recompression with particular algorithm only:
echo "type=idle algo=zstd" > /sys/block/zramX/recompress
Link: https://lkml.kernel.org/r/20221109115047.2921851-11-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Alexey Romanov <avromanov@sberdevices.ru>
Cc: Nhat Pham <nphamcs@gmail.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
It makes no sense for us to recompress the object if it will be in the
same size class. We anyway don't get any memory gain. But, at the same
time, we get a CPU time overhead when inserting this object into zspage
and decompressing it afterwards.
[senozhatsky: rebased and fixed conflicts]
Link: https://lkml.kernel.org/r/20221109115047.2921851-9-senozhatsky@chromium.org
Signed-off-by: Alexey Romanov <avromanov@sberdevices.ru>
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Nhat Pham <nphamcs@gmail.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Add a new flag to zram block state that shows if the page was recompressed
(using alternative compression algorithm).
Link: https://lkml.kernel.org/r/20221109115047.2921851-6-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Alexey Romanov <avromanov@sberdevices.ru>
Cc: Nhat Pham <nphamcs@gmail.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Allow zram to recompress (using secondary compression streams)
pages.
Re-compression algorithms (we support up to 3 at this stage)
are selected via recomp_algorithm:
echo "algo=zstd priority=1" > /sys/block/zramX/recomp_algorithm
Please read documentation for more details.
We support several recompression modes:
1) IDLE pages recompression is activated by `idle` mode
echo "type=idle" > /sys/block/zram0/recompress
2) Since there may be many idle pages user-space may pass a size
threshold value (in bytes) and we will recompress pages only
of equal or greater size:
echo "threshold=888" > /sys/block/zram0/recompress
3) HUGE pages recompression is activated by `huge` mode
echo "type=huge" > /sys/block/zram0/recompress
4) HUGE_IDLE pages recompression is activated by `huge_idle` mode
echo "type=huge_idle" > /sys/block/zram0/recompress
[senozhatsky@chromium.org: we should always zero out err variable in recompress loop[
Link: https://lkml.kernel.org/r/20221110143423.3250790-1-senozhatsky@chromium.org
Link: https://lkml.kernel.org/r/20221109115047.2921851-5-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Alexey Romanov <avromanov@sberdevices.ru>
Cc: Nhat Pham <nphamcs@gmail.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Introduce recomp_algorithm sysfs knob that controls secondary algorithm
selection used for recompression.
We will support up to 3 secondary compression algorithms which are sorted
in order of their priority. To select an algorithm user has to provide
its name and priority:
echo "algo=zstd priority=1" > /sys/block/zramX/recomp_algorithm
echo "algo=deflate priority=2" > /sys/block/zramX/recomp_algorithm
During recompression zram iterates through the list of registered
secondary algorithms in order of their priorities.
We also have a short version for cases when there is only
one secondary compression algorithm:
echo "algo=zstd" > /sys/block/zramX/recomp_algorithm
This will register zstd as the secondary algorithm with priority 1.
Link: https://lkml.kernel.org/r/20221109115047.2921851-3-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Alexey Romanov <avromanov@sberdevices.ru>
Cc: Nhat Pham <nphamcs@gmail.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "zram: Support multiple compression streams", v5.
This series adds support for multiple compression streams. The main idea
is that different compression algorithms have different characteristics
and zram may benefit when it uses a combination of algorithms: a default
algorithm that is faster but have lower compression rate and a secondary
algorithm that can use higher compression rate at a price of slower
compression/decompression.
There are several use-case for this functionality:
- huge pages re-compression: zstd or deflate can successfully compress
huge pages (~50% of huge pages on my synthetic ChromeOS tests), IOW
pages that lzo was not able to compress.
- idle pages re-compression: idle/cold pages sit in the memory and we
may reduce zsmalloc memory usage if we recompress those idle pages.
Userspace has a number of ways to control the behavior and impact of zram
recompression: what type of pages should be recompressed, size watermarks,
etc. Please refer to documentation patch.
This patch (of 13):
The patch turns compression streams and compressor algorithm name struct
zram members into arrays, so that we can have multiple compression streams
support (in the next patches).
The patch uses a rather explicit API for compressor selection:
- Get primary (default) compression stream
zcomp_stream_get(zram->comps[ZRAM_PRIMARY_COMP])
- Get secondary compression stream
zcomp_stream_get(zram->comps[ZRAM_SECONDARY_COMP])
We use similar API for compression streams put().
At this point we always have just one compression stream,
since CONFIG_ZRAM_MULTI_COMP is not yet defined.
Link: https://lkml.kernel.org/r/20221109115047.2921851-1-senozhatsky@chromium.org
Link: https://lkml.kernel.org/r/20221109115047.2921851-2-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Nhat Pham <nphamcs@gmail.com>
Cc: Alexey Romanov <avromanov@sberdevices.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
ida_simple[get|remove] are deprecated, and are just wrappers to
ida_[alloc_range|free]. Replace ida_simple[get|remove] with their
corresponding counterparts.
No functional changes.
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Link: https://lore.kernel.org/r/20221130123001.25473-1-p.raghav@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=41zr
-----END PGP SIGNATURE-----
Merge tag 'block-6.1-2022-11-25' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- A few fixes for s390 sads (Stefan, Colin)
- Ensure that ublk doesn't reorder requests, as that can be problematic
on devices that need specific ordering (Ming)
- Fix a queue reference leak in disk allocation handling (Christoph)
* tag 'block-6.1-2022-11-25' of git://git.kernel.dk/linux:
ublk_drv: don't forward io commands in reserve order
s390/dasd: fix possible buffer overflow in copy_pair_show
s390/dasd: fix no record found for raw_track_access
s390/dasd: increase printing of debug data payload
s390/dasd: Fix spelling mistake "Ivalid" -> "Invalid"
blk-mq: fix queue reference leak on blk_mq_alloc_disk_for_queue failure
READ/WRITE proved to be actively confusing - the meanings are
"data destination, as used with read(2)" and "data source, as
used with write(2)", but people keep interpreting those as
"we read data from it" and "we write data to it", i.e. exactly
the wrong way.
Call them ITER_DEST and ITER_SOURCE - at least that is harder
to misinterpret...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The devnode() in struct class should not be modifying the device that is
passed into it, so mark it as a const * and propagate the function
signature changes out into all relevant subsystems that use this
callback.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: x86@kernel.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Justin Sanders <justin@coraid.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Cc: Liam Mark <lmark@codeaurora.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Brian Starkey <Brian.Starkey@arm.com>
Cc: John Stultz <jstultz@google.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Sean Young <sean@mess.org>
Cc: Frank Haverkamp <haver@linux.ibm.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Xie Yongji <xieyongji@bytedance.com>
Cc: Gautam Dawar <gautam.dawar@xilinx.com>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Eli Cohen <elic@nvidia.com>
Cc: Parav Pandit <parav@nvidia.com>
Cc: Maxime Coquelin <maxime.coquelin@redhat.com>
Cc: alsa-devel@alsa-project.org
Cc: dri-devel@lists.freedesktop.org
Cc: kvm@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: linux-block@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Link: https://lore.kernel.org/r/20221123122523.1332370-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A submitter workqueue is dynamically allocated by init_submitter()
called by drbd_create_device(), we should destroy it when this
device is not needed or destroyed.
Fixes: 113fef9e20 ("drbd: prepare to queue write requests on a submit worker")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Link: https://lore.kernel.org/r/20221124015817.2729789-3-bobo.shaobowang@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This revert c2258ffc56 ("drbd: poison free'd device, resource and
connection structs"), add memset is odd here for debugging, there are
some methods to accurately show what happened, such as kdump.
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Link: https://lore.kernel.org/r/20221124015817.2729789-2-bobo.shaobowang@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Either ublk_can_use_task_work() is true or not, io commands are
forwarded to ublk server in reverse order, since llist_add() is
always to add one element to the head of the list.
Even though block layer doesn't guarantee request dispatch order,
requests should be sent to hardware in the sequence order generated
from io scheduler, which usually considers the request's LBA, and
order is often important for HDD.
So forward io commands in the sequence made from io scheduler by
aligning task work with current io_uring command's batch handling,
and it has been observed that both can get similar performance data
if IORING_SETUP_COOP_TASKRUN is set from ublk server.
Reported-by: Andreas Hindborg <andreas.hindborg@wdc.com>
Cc: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221121155645.396272-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
DRBD currently has a mix of GPL-2.0 and GPL-2.0-or-later SPDX license
identifiers. We have decided to stick with GPL 2.0 only, so consistently
use that identifier.
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20221122134301.69258-5-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=sOGG
-----END PGP SIGNATURE-----
Merge tag 'block-6.1-2022-11-18' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- NVMe pull request via Christoph:
- Two more bogus nid quirks (Bean Huo, Tiago Dias Ferreira)
- Memory leak fix in nvmet (Sagi Grimberg)
- Regression fix for block cgroups pinning the wrong blkcg, causing
leaks of cgroups and blkcgs (Chris)
- UAF fix for drbd setup error handling (Dan)
- Fix DMA alignment propagation in DM (Keith)
* tag 'block-6.1-2022-11-18' of git://git.kernel.dk/linux:
dm-log-writes: set dma_alignment limit in io_hints
dm-integrity: set dma_alignment limit in io_hints
block: make blk_set_default_limits() private
dm-crypt: provide dma_alignment limit in io_hints
block: make dma_alignment a stacking queue_limit
nvmet: fix a memory leak in nvmet_auth_set_key
nvme-pci: add NVME_QUIRK_BOGUS_NID for Netac NV7000
drbd: use after free in drbd_create_device()
nvme-pci: add NVME_QUIRK_BOGUS_NID for Micron Nitro
blk-cgroup: properly pin the parent in blkcg_css_online
This is a simple mechanical transformation done by:
@@
expression E;
@@
- prandom_u32_max
+ get_random_u32_below
(E)
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Reviewed-by: SeongJae Park <sj@kernel.org> # for damon
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> # for infiniband
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> # for arm
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for mmc
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The drbd_destroy_connection() frees the "connection" so use the _safe()
iterator to prevent a use after free.
Fixes: b6f85ef953 ("drbd: Iterate over all connections")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/Y3Jd5iZRbNQ9w6gm@kili
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The devnode() callback in struct block_device_operations should not be
modifying the device that is passed into it, so mark it as a const * and
propagate the function signature changes out into the one subsystem that
actually uses this callback.
Acked-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/20221109144843.679668-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(Sort of) cherry-picked from the out-of-tree drbd9 branch. Original
commit message by Joel Colledge:
This simplifies drbd_submit_peer_request by removing most of the
arguments. It also makes the treatment of the op better aligned with
that in struct bio.
Determine fault_type dynamically using information which is already
available instead of passing it in as a parameter.
Note: The opf in receive_rs_deallocated was changed from
REQ_OP_WRITE_ZEROES to REQ_OP_DISCARD. This was required in the
out-of-tree module, and does not matter in-tree. The opf is ignored
anyway in drbd_submit_peer_request, since the discard/zero-out is
decided by the EE_TRIM flag.
Signed-off-by: Joel Colledge <joel.colledge@linbit.com>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20221109133453.51652-4-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The discard_granularity describes the minimum unit of a discard.
If that is larger than the maximal discard size, we need to disable
discards completely.
Reviewed-by: Joel Colledge <joel.colledge@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20221109133453.51652-3-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We currently only set q->limits.max_discard_sectors, but that is not
enough. Another field, max_hw_discard_sectors, was introduced in
commit 0034af0365 ("block: make /sys/block/<dev>/queue/discard_max_bytes
writeable").
The difference is that max_discard_sectors can be changed from user
space via sysfs, while max_hw_discard_sectors is the "hardware" upper
limit.
So use this helper, which sets both.
This is also a fixup for commit 998e9cbcd6 ("drbd: cleanup
decide_on_discard_support"): if discards are not supported, that does
not necessarily mean we also want to disable write_zeroes.
Fixes: 998e9cbcd6 ("drbd: cleanup decide_on_discard_support")
Reviewed-by: Joel Colledge <joel.colledge@linbit.com>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20221109133453.51652-2-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use try_cmpxchg instead of cmpxchg (*ptr, old, new) == old in
update_used_max. x86 CMPXCHG instruction returns success in ZF flag, so
this change saves a compare after cmpxchg (and related move instruction in
front of cmpxchg).
Also, reorder code a bit to remove additional compare and conditional jump
from the assembly code. Together, hese two changes save 15 bytes from the
function when compiled for x86_64.
No functional change intended.
Link: https://lkml.kernel.org/r/20221018145154.3699-1-ubizjak@gmail.com
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAmNmdGEQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpvLpD/9pL9SLpoUAnSvYAzaJC0dJhFHzQhmQgA55
qxwgC4NDyxYgvsLuHVVoR5qRSNQO37nKkgoeHsqSX56UTloQnggurg0Cr94VJcjC
seT1++Dl6BPz1M9h/UFS2cwm26GC+cQmsLIQoACSi0lNEOLytPP/emq6Vuqz0udx
ah1ACXebiHe07A8Kvpt7orHlpM/dKH0/4g5/7h0E5RWrC9yg1WEOHPjd/MQ5amy0
9YkhtqM5OQfNsVY0DcRbgRPr115xSi/L6No3Q6pMAVqzM7ZRk3iD039be7Sooqn8
sl54gZB3AWGzgrFnJLjKCcQg4qg/wyYhZXEuV2JdzYeXCBK6RMcV0I2hP6vWP7Au
dqlw5khvQOwx32qYNlXHU7g/ve5qY7hblIHbyqtKjQicIQ8LP18Ek1QWQcywiK4E
hyYJ/3gYRjVqigyw32++cMSRLbLktiY38+J7NxujIj6J1aOYosCA5kIxTSa11tLG
VGeXny5CS5l0zrl3irGBRI1Qi33T0hnbmf99v+MndFhRfsYAF8tKwuJyI+d+rJvj
S8grDzsmlzwe1INXEbnMEg+SsHOPe5On0bzYIYX9Oi0BSsZf1i4u7SdDb9tu2Tiw
WSJyYBNGCsl7wFSoLmY75j1OvWY/iXYPKqZ8bt9STQbO9vL+VHksFzcnnkvzrBG6
Zs1uD17jwQ==
=JQlF
-----END PGP SIGNATURE-----
Merge tag 'block-6.1-2022-11-05' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- Fixes for the ublk driver (Ming)
- Fixes for error handling memory leaks (Chen Jun, Chen Zhongjin)
- Explicitly clear the last request in a chain when the plug is
flushed, as it may have already been issued (Al)
* tag 'block-6.1-2022-11-05' of git://git.kernel.dk/linux:
block: blk_add_rq_to_plug(): clear stale 'last' after flush
blk-mq: Fix kmemleak in blk_mq_init_allocated_queue
block: Fix possible memory leak for rq_wb on add_disk failure
ublk_drv: add ublk_queue_cmd() for cleanup
ublk_drv: avoid to touch io_uring cmd in blk_mq io path
ublk_drv: comment on ublk_driver entry of Kconfig
ublk_drv: return flag of UBLK_F_URING_CMD_COMP_IN_TASK in case of module
nvme and xen-blkfront are already doing this to stop buffered writes from
creating dirty pages that can't be written out later. Move it to the
common code.
This also removes the comment about the ordering from nvme, as bd_mutex
not only is gone entirely, but also hasn't been used for locking updates
to the disk size long before that, and thus the ordering requirement
documented there doesn't apply any more.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Chao Leng <lengchao@huawei.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20221101150050.3510-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add helper of ublk_queue_cmd() so that both ublk_queue_rq()
and ublk_handle_need_get_data() can reuse this helper.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221029010432.598367-5-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_uring cmd is supposed to be used in ubq daemon context mainly,
and we should try to avoid to touch it in ublk io submission context,
otherwise this data could become shared between the two contexts,
and performance is hurt.
So link request into one per-queue list, and use same batching policy
of io_uring command, just avoid to touch ucmd in blk-mq io context.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221029010432.598367-4-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add help info for choosing to build ublk_drv as module or builtin.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221029010432.598367-3-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
UBLK_F_URING_CMD_COMP_IN_TASK needs to be set and returned to userspace
if ublk driver is built as module, otherwise userspace may get wrong
flags shown.
Fixes: 71f28f3136 ("ublk_drv: add io_uring based userspace block driver")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221029010432.598367-2-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAmNcRTYQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpkc2D/4yxjQ+lAmXLrqZOGAZc+r2GpiCFsgFcpKP
i3ezeeo3zmdaoUH778DcbPo0oeWY/iIvV2RDo3/0PBHIlGL43W9e7zsnauRxUwtw
/Aj140Tsm5/lKnBy8n0nT+DO4LE22JnBHi5XjlFELBwM+deBxS+izinFtcOQC8sj
58XWSmKag/Lv5JLvcYMj+PprtGOKzfNAacXvTjouy0IlEyb9E/yPMELS8lWFv8i2
QELtvuEDxODpQtA+Ph0O/o00A8Fg/lC4EH5uvExFMr8k74CGFm32Bar1UuaJ9QAs
5b8wateTra51yOGW3NEl1ph+4qVe9e4mutrLOFrChYylk5LePOVAki3wYb3lREiU
rTOEKzUj3P/LHLpl4els0yIQ0gHXs60/M/Vn3TC50+2DnV00qEfvaocZ8vtXOux4
YR+2cKUxk2CRNyj2BB3WRlrIkCIVk+ehl17E2cdrg0m8SMqk0GAYbpXD753L9uiy
I7IQEqYB+op501pmTcVskFUfW9ozT96YD53fwSOTR/pEK+esHN0GfqxI6lcA6Q0O
M2AWEiu8t1PbSONVH/p895gfgGHdRHl6zgvR+ADJMDEmc7dpEoAxsoTj4HIirXbe
sGHi7ycrQR6aLdHahjCukjUVkZkuhXJkAQmq2XURJgmEcz7iJme23WqtWWUUoQvi
pk6e1RSqSA==
=Zfnu
-----END PGP SIGNATURE-----
Merge tag 'block-6.1-2022-10-28' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- NVMe pull request via Christoph:
- make the multipath dma alignment match the non-multipath one
(Keith Busch)
- fix a bogus use of sg_init_marker() (Nam Cao)
- fix circulr locking in nvme-tcp (Sagi Grimberg)
- Initialization fix for requests allocated via the special hw queue
allocator (John)
- Fix for a regression added in this release with the batched
completions of end_io backed requests (Ming)
- Error handling leak fix for rbd (Yang)
- Error handling leak fix for add_disk() failure (Yu)
* tag 'block-6.1-2022-10-28' of git://git.kernel.dk/linux:
blk-mq: Properly init requests from blk_mq_alloc_request_hctx()
blk-mq: don't add non-pt request with ->end_io to batch
rbd: fix possible memory leak in rbd_sysfs_init()
nvme-multipath: set queue dma alignment to 3
nvme-tcp: fix possible circular locking when deleting a controller under memory pressure
nvme-tcp: replace sg_init_marker() with sg_init_table()
block: fix memory leak for elevator on add_disk failure
If device_register() returns error in rbd_sysfs_init(), name of kobject
which is allocated in dev_set_name() called in device_add() is leaked.
As comment of device_add() says, it should call put_device() to drop
the reference count that was set in device_initialize() when it fails,
so the name can be freed in kobject_cleanup().
Fault injection test can trigger this problem:
unreferenced object 0xffff88810173aa78 (size 8):
comm "modprobe", pid 247, jiffies 4294714278 (age 31.789s)
hex dump (first 8 bytes):
72 62 64 00 81 88 ff ff rbd.....
backtrace:
[<00000000f58fae56>] __kmalloc_node_track_caller+0x44/0x1b0
[<00000000bdd44fe7>] kstrdup+0x3a/0x70
[<00000000f7844d0b>] kstrdup_const+0x63/0x80
[<000000001b0a0eeb>] kvasprintf_const+0x10b/0x190
[<00000000a47bd894>] kobject_set_name_vargs+0x56/0x150
[<00000000d5edbf18>] dev_set_name+0xab/0xe0
[<00000000f5153e80>] device_add+0x106/0x1f20
Fixes: dfc5606dc5 ("rbd: replace the rbd sysfs interface")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20221027091918.2294132-1-yangyingliang@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit c347a787e3 (drbd: set ->bi_bdev in drbd_req_new) moved a
bio_set_dev call (which has since been removed) to "earlier", from
drbd_request_prepare to drbd_req_new.
The problem is that this accesses device->ldev->backing_bdev, which is
not NULL-checked at this point. When we don't have an ldev (i.e. when
the DRBD device is diskless), this leads to a null pointer deref.
So, only allocate the private_bio if we actually have a disk. This is
also a small optimization, since we don't clone the bio to only to
immediately free it again in the diskless case.
Fixes: c347a787e3 ("drbd: set ->bi_bdev in drbd_req_new")
Co-developed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Co-developed-by: Joel Colledge <joel.colledge@linbit.com>
Signed-off-by: Joel Colledge <joel.colledge@linbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20221020085205.129090-1-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Eliminate the following coccicheck warning:
./drivers/block/ublk_drv.c:127:16-19: WARNING use flexible-array member instead
Signed-off-by: Yushan Zhou <katrinzhou@tencent.com>
Link: https://lore.kernel.org/r/20221018100132.355393-1-zys.zljxml@gmail.com
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=M+mV
-----END PGP SIGNATURE-----
Merge tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull more random number generator updates from Jason Donenfeld:
"This time with some large scale treewide cleanups.
The intent of this pull is to clean up the way callers fetch random
integers. The current rules for doing this right are:
- If you want a secure or an insecure random u64, use get_random_u64()
- If you want a secure or an insecure random u32, use get_random_u32()
The old function prandom_u32() has been deprecated for a while
now and is just a wrapper around get_random_u32(). Same for
get_random_int().
- If you want a secure or an insecure random u16, use get_random_u16()
- If you want a secure or an insecure random u8, use get_random_u8()
- If you want secure or insecure random bytes, use get_random_bytes().
The old function prandom_bytes() has been deprecated for a while
now and has long been a wrapper around get_random_bytes()
- If you want a non-uniform random u32, u16, or u8 bounded by a
certain open interval maximum, use prandom_u32_max()
I say "non-uniform", because it doesn't do any rejection sampling
or divisions. Hence, it stays within the prandom_*() namespace, not
the get_random_*() namespace.
I'm currently investigating a "uniform" function for 6.2. We'll see
what comes of that.
By applying these rules uniformly, we get several benefits:
- By using prandom_u32_max() with an upper-bound that the compiler
can prove at compile-time is ≤65536 or ≤256, internally
get_random_u16() or get_random_u8() is used, which wastes fewer
batched random bytes, and hence has higher throughput.
- By using prandom_u32_max() instead of %, when the upper-bound is
not a constant, division is still avoided, because
prandom_u32_max() uses a faster multiplication-based trick instead.
- By using get_random_u16() or get_random_u8() in cases where the
return value is intended to indeed be a u16 or a u8, we waste fewer
batched random bytes, and hence have higher throughput.
This series was originally done by hand while I was on an airplane
without Internet. Later, Kees and I worked on retroactively figuring
out what could be done with Coccinelle and what had to be done
manually, and then we split things up based on that.
So while this touches a lot of files, the actual amount of code that's
hand fiddled is comfortably small"
* tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
prandom: remove unused functions
treewide: use get_random_bytes() when possible
treewide: use get_random_u32() when possible
treewide: use get_random_{u8,u16}() when possible, part 2
treewide: use get_random_{u8,u16}() when possible, part 1
treewide: use prandom_u32_max() when possible, part 2
treewide: use prandom_u32_max() when possible, part 1
refcounting errors in ZONE_DEVICE pages.
- Peter Xu fixes some userfaultfd test harness instability.
- Various other patches in MM, mainly fixes.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCY0j6igAKCRDdBJ7gKXxA
jnGxAP99bV39ZtOsoY4OHdZlWU16BUjKuf/cb3bZlC2G849vEwD+OKlij86SG20j
MGJQ6TfULJ8f1dnQDd6wvDfl3FMl7Qc=
=tbdp
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2022-10-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull more MM updates from Andrew Morton:
- fix a race which causes page refcounting errors in ZONE_DEVICE pages
(Alistair Popple)
- fix userfaultfd test harness instability (Peter Xu)
- various other patches in MM, mainly fixes
* tag 'mm-stable-2022-10-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (29 commits)
highmem: fix kmap_to_page() for kmap_local_page() addresses
mm/page_alloc: fix incorrect PGFREE and PGALLOC for high-order page
mm/selftest: uffd: explain the write missing fault check
mm/hugetlb: use hugetlb_pte_stable in migration race check
mm/hugetlb: fix race condition of uffd missing/minor handling
zram: always expose rw_page
LoongArch: update local TLB if PTE entry exists
mm: use update_mmu_tlb() on the second thread
kasan: fix array-bounds warnings in tests
hmm-tests: add test for migrate_device_range()
nouveau/dmem: evict device private memory during release
nouveau/dmem: refactor nouveau_dmem_fault_copy_one()
mm/migrate_device.c: add migrate_device_range()
mm/migrate_device.c: refactor migrate_vma and migrate_deivce_coherent_page()
mm/memremap.c: take a pgmap reference on page allocation
mm: free device private pages have zero refcount
mm/memory.c: fix race when faulting a device private page
mm/damon: use damon_sz_region() in appropriate place
mm/damon: move sz_damon_region to damon_sz_region
lib/test_meminit: add checks for the allocation functions
...
Currently zram will adjust its fops to a version which does not contain
rw_page when a backing device has been assigned. This is done to prevent
upper layers from assuming a synchronous operation when a page may have
been written back. This forces every operation through bio which has
overhead associated with bio_alloc/frees.
The code can be simplified to always expose an rw_page method and only in
the rare event that a page is written back we instead will return
-EOPNOTSUPP forcing the upper layer to fallback to bio.
Link: https://lkml.kernel.org/r/20221003144832.2906610-1-bgeffon@google.com
Signed-off-by: Brian Geffon <bgeffon@google.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Rom Lemarchand <romlem@google.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Rather than incurring a division or requesting too many random bytes for
the given range, use the prandom_u32_max() function, which only takes
the minimum required bytes from the RNG and avoids divisions. This was
done mechanically with this coccinelle script:
@basic@
expression E;
type T;
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
typedef u64;
@@
(
- ((T)get_random_u32() % (E))
+ prandom_u32_max(E)
|
- ((T)get_random_u32() & ((E) - 1))
+ prandom_u32_max(E * XXX_MAKE_SURE_E_IS_POW2)
|
- ((u64)(E) * get_random_u32() >> 32)
+ prandom_u32_max(E)
|
- ((T)get_random_u32() & ~PAGE_MASK)
+ prandom_u32_max(PAGE_SIZE)
)
@multi_line@
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
identifier RAND;
expression E;
@@
- RAND = get_random_u32();
... when != RAND
- RAND %= (E);
+ RAND = prandom_u32_max(E);
// Find a potential literal
@literal_mask@
expression LITERAL;
type T;
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
position p;
@@
((T)get_random_u32()@p & (LITERAL))
// Add one to the literal.
@script:python add_one@
literal << literal_mask.LITERAL;
RESULT;
@@
value = None
if literal.startswith('0x'):
value = int(literal, 16)
elif literal[0] in '123456789':
value = int(literal, 10)
if value is None:
print("I don't know how to handle %s" % (literal))
cocci.include_match(False)
elif value == 2**32 - 1 or value == 2**31 - 1 or value == 2**24 - 1 or value == 2**16 - 1 or value == 2**8 - 1:
print("Skipping 0x%x for cleanup elsewhere" % (value))
cocci.include_match(False)
elif value & (value + 1) != 0:
print("Skipping 0x%x because it's not a power of two minus one" % (value))
cocci.include_match(False)
elif literal.startswith('0x'):
coccinelle.RESULT = cocci.make_expr("0x%x" % (value + 1))
else:
coccinelle.RESULT = cocci.make_expr("%d" % (value + 1))
// Replace the literal mask with the calculated result.
@plus_one@
expression literal_mask.LITERAL;
position literal_mask.p;
expression add_one.RESULT;
identifier FUNC;
@@
- (FUNC()@p & (LITERAL))
+ prandom_u32_max(RESULT)
@collapse_ret@
type T;
identifier VAR;
expression E;
@@
{
- T VAR;
- VAR = (E);
- return VAR;
+ return E;
}
@drop_var@
type T;
identifier VAR;
@@
{
- T VAR;
... when != VAR
}
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: KP Singh <kpsingh@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4 and sbitmap
Reviewed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> # for drbd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for mmc
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
linux-next for a couple of months without, to my knowledge, any negative
reports (or any positive ones, come to that).
- Also the Maple Tree from Liam R. Howlett. An overlapping range-based
tree for vmas. It it apparently slight more efficient in its own right,
but is mainly targeted at enabling work to reduce mmap_lock contention.
Liam has identified a number of other tree users in the kernel which
could be beneficially onverted to mapletrees.
Yu Zhao has identified a hard-to-hit but "easy to fix" lockdep splat
(https://lkml.kernel.org/r/CAOUHufZabH85CeUN-MEMgL8gJGzJEWUrkiM58JkTbBhh-jew0Q@mail.gmail.com).
This has yet to be addressed due to Liam's unfortunately timed
vacation. He is now back and we'll get this fixed up.
- Dmitry Vyukov introduces KMSAN: the Kernel Memory Sanitizer. It uses
clang-generated instrumentation to detect used-unintialized bugs down to
the single bit level.
KMSAN keeps finding bugs. New ones, as well as the legacy ones.
- Yang Shi adds a userspace mechanism (madvise) to induce a collapse of
memory into THPs.
- Zach O'Keefe has expanded Yang Shi's madvise(MADV_COLLAPSE) to support
file/shmem-backed pages.
- userfaultfd updates from Axel Rasmussen
- zsmalloc cleanups from Alexey Romanov
- cleanups from Miaohe Lin: vmscan, hugetlb_cgroup, hugetlb and memory-failure
- Huang Ying adds enhancements to NUMA balancing memory tiering mode's
page promotion, with a new way of detecting hot pages.
- memcg updates from Shakeel Butt: charging optimizations and reduced
memory consumption.
- memcg cleanups from Kairui Song.
- memcg fixes and cleanups from Johannes Weiner.
- Vishal Moola provides more folio conversions
- Zhang Yi removed ll_rw_block() :(
- migration enhancements from Peter Xu
- migration error-path bugfixes from Huang Ying
- Aneesh Kumar added ability for a device driver to alter the memory
tiering promotion paths. For optimizations by PMEM drivers, DRM
drivers, etc.
- vma merging improvements from Jakub Matěn.
- NUMA hinting cleanups from David Hildenbrand.
- xu xin added aditional userspace visibility into KSM merging activity.
- THP & KSM code consolidation from Qi Zheng.
- more folio work from Matthew Wilcox.
- KASAN updates from Andrey Konovalov.
- DAMON cleanups from Kaixu Xia.
- DAMON work from SeongJae Park: fixes, cleanups.
- hugetlb sysfs cleanups from Muchun Song.
- Mike Kravetz fixes locking issues in hugetlbfs and in hugetlb core.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCY0HaPgAKCRDdBJ7gKXxA
joPjAQDZ5LlRCMWZ1oxLP2NOTp6nm63q9PWcGnmY50FjD/dNlwEAnx7OejCLWGWf
bbTuk6U2+TKgJa4X7+pbbejeoqnt5QU=
=xfWx
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2022-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- Yu Zhao's Multi-Gen LRU patches are here. They've been under test in
linux-next for a couple of months without, to my knowledge, any
negative reports (or any positive ones, come to that).
- Also the Maple Tree from Liam Howlett. An overlapping range-based
tree for vmas. It it apparently slightly more efficient in its own
right, but is mainly targeted at enabling work to reduce mmap_lock
contention.
Liam has identified a number of other tree users in the kernel which
could be beneficially onverted to mapletrees.
Yu Zhao has identified a hard-to-hit but "easy to fix" lockdep splat
at [1]. This has yet to be addressed due to Liam's unfortunately
timed vacation. He is now back and we'll get this fixed up.
- Dmitry Vyukov introduces KMSAN: the Kernel Memory Sanitizer. It uses
clang-generated instrumentation to detect used-unintialized bugs down
to the single bit level.
KMSAN keeps finding bugs. New ones, as well as the legacy ones.
- Yang Shi adds a userspace mechanism (madvise) to induce a collapse of
memory into THPs.
- Zach O'Keefe has expanded Yang Shi's madvise(MADV_COLLAPSE) to
support file/shmem-backed pages.
- userfaultfd updates from Axel Rasmussen
- zsmalloc cleanups from Alexey Romanov
- cleanups from Miaohe Lin: vmscan, hugetlb_cgroup, hugetlb and
memory-failure
- Huang Ying adds enhancements to NUMA balancing memory tiering mode's
page promotion, with a new way of detecting hot pages.
- memcg updates from Shakeel Butt: charging optimizations and reduced
memory consumption.
- memcg cleanups from Kairui Song.
- memcg fixes and cleanups from Johannes Weiner.
- Vishal Moola provides more folio conversions
- Zhang Yi removed ll_rw_block() :(
- migration enhancements from Peter Xu
- migration error-path bugfixes from Huang Ying
- Aneesh Kumar added ability for a device driver to alter the memory
tiering promotion paths. For optimizations by PMEM drivers, DRM
drivers, etc.
- vma merging improvements from Jakub Matěn.
- NUMA hinting cleanups from David Hildenbrand.
- xu xin added aditional userspace visibility into KSM merging
activity.
- THP & KSM code consolidation from Qi Zheng.
- more folio work from Matthew Wilcox.
- KASAN updates from Andrey Konovalov.
- DAMON cleanups from Kaixu Xia.
- DAMON work from SeongJae Park: fixes, cleanups.
- hugetlb sysfs cleanups from Muchun Song.
- Mike Kravetz fixes locking issues in hugetlbfs and in hugetlb core.
Link: https://lkml.kernel.org/r/CAOUHufZabH85CeUN-MEMgL8gJGzJEWUrkiM58JkTbBhh-jew0Q@mail.gmail.com [1]
* tag 'mm-stable-2022-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (555 commits)
hugetlb: allocate vma lock for all sharable vmas
hugetlb: take hugetlb vma_lock when clearing vma_lock->vma pointer
hugetlb: fix vma lock handling during split vma and range unmapping
mglru: mm/vmscan.c: fix imprecise comments
mm/mglru: don't sync disk for each aging cycle
mm: memcontrol: drop dead CONFIG_MEMCG_SWAP config symbol
mm: memcontrol: use do_memsw_account() in a few more places
mm: memcontrol: deprecate swapaccounting=0 mode
mm: memcontrol: don't allocate cgroup swap arrays when memcg is disabled
mm/secretmem: remove reduntant return value
mm/hugetlb: add available_huge_pages() func
mm: remove unused inline functions from include/linux/mm_inline.h
selftests/vm: add selftest for MADV_COLLAPSE of uffd-minor memory
selftests/vm: add file/shmem MADV_COLLAPSE selftest for cleared pmd
selftests/vm: add thp collapse shmem testing
selftests/vm: add thp collapse file and tmpfs testing
selftests/vm: modularize thp collapse memory operations
selftests/vm: dedup THP helpers
mm/khugepaged: add tracepoint to hpage_collapse_scan_file()
mm/madvise: add file and shmem support to MADV_COLLAPSE
...
9k mtu perf improvements
vdpa feature provisioning
virtio blk SECURE ERASE support
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmNAvcMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpYaMH/0hv6q1D35lLinVn4DSz8ru754picK9Pg8Vv
dJG8w0v3VN1lHLBQ63Gj9/M47odCq8JeeDwmkzVs3C2I3pwLdcO1Yd+fkqGVP7gd
Fc7cyi87sk4heHEm6K5jC17gf3k39rS9BkFbYFyPQzr/+6HXx6O/6x7StxvY9EB0
nst7yjPxKXptF5Sf3uUFk4YIFxSvkmvV292sLrWvkaMjn71oJXqsr8yNCFcqv/jk
KM7C8ZCRuydatM+PEuJPcveJd04jYuoNS3OZDCCWD6XuzLROQ10PbLBBqoHLEWu7
wZbY4WndJSqnRE3dx0Xm8LgKNPOBxVfDoD3RVejxW6JF9hmGcG8=
=PIpt
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
- 9k mtu perf improvements
- vdpa feature provisioning
- virtio blk SECURE ERASE support
- fixes and cleanups all over the place
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_pci: don't try to use intxif pin is zero
vDPA: conditionally read MTU and MAC in dev cfg space
vDPA: fix spars cast warning in vdpa_dev_net_mq_config_fill
vDPA: check virtio device features to detect MQ
vDPA: check VIRTIO_NET_F_RSS for max_virtqueue_paris's presence
vDPA: only report driver features if FEATURES_OK is set
vDPA: allow userspace to query features of a vDPA device
virtio_blk: add SECURE ERASE command support
vp_vdpa: support feature provisioning
vdpa_sim_net: support feature provisioning
vdpa: device feature provisioning
virtio-net: use mtu size as buffer length for big packets
virtio-net: introduce and use helper function for guest gso support checks
virtio: drop vp_legacy_set_queue_size
virtio_ring: make vring_alloc_queue_packed prettier
virtio_ring: split: Operators use unified style
vhost: add __init/__exit annotations to module init/exit funcs
Here is the big set of driver core and debug printk changes for 6.1-rc1.
Included in here is:
- dynamic debug updates for the core and the drm subsystem. The
drm changes have all been acked by the relevant maintainers.
- kernfs fixes for syzbot reported problems
- kernfs refactors and updates for cgroup requirements
- magic number cleanups and removals from the kernel tree (they
were not being used and they really did not actually do
anything.)
- other tiny cleanups
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0BYUA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylozwCdFRlcghaf7XBUyNgRZRwMC+oQI8EAn1G/nEDE
6aFd2er41uK0IGQnSmYO
=OK0k
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core and debug printk changes for
6.1-rc1. Included in here is:
- dynamic debug updates for the core and the drm subsystem. The drm
changes have all been acked by the relevant maintainers
- kernfs fixes for syzbot reported problems
- kernfs refactors and updates for cgroup requirements
- magic number cleanups and removals from the kernel tree (they were
not being used and they really did not actually do anything)
- other tiny cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (74 commits)
docs: filesystems: sysfs: Make text and code for ->show() consistent
Documentation: NBD_REQUEST_MAGIC isn't a magic number
a.out: restore CMAGIC
device property: Add const qualifier to device_get_match_data() parameter
drm_print: add _ddebug descriptor to drm_*dbg prototypes
drm_print: prefer bare printk KERN_DEBUG on generic fn
drm_print: optimize drm_debug_enabled for jump-label
drm-print: add drm_dbg_driver to improve namespace symmetry
drm-print.h: include dyndbg header
drm_print: wrap drm_*_dbg in dyndbg descriptor factory macro
drm_print: interpose drm_*dbg with forwarding macros
drm: POC drm on dyndbg - use in core, 2 helpers, 3 drivers.
drm_print: condense enum drm_debug_category
debugfs: use DEFINE_SHOW_ATTRIBUTE to define debugfs_regset32_fops
driver core: use IS_ERR_OR_NULL() helper in device_create_groups_vargs()
Documentation: ENI155_MAGIC isn't a magic number
Documentation: NBD_REPLY_MAGIC isn't a magic number
nbd: remove define-only NBD_MAGIC, previously magic number
Documentation: FW_HEADER_MAGIC isn't a magic number
Documentation: EEPROM_MAGIC_VALUE isn't a magic number
...
- Small bug fixes in mlx5, efa, rxe, hns, irdma, erdma, siw
- rts tracing improvements
- Code improvements: strlscpy conversion, unused parameter, spelling
mistakes, unused variables, flex arrays
- restrack device details report for hns
- Simplify struct device initialization in SRP
- Eliminate the never-used service_mask support in IB CM
- Make rxe not print to the console for some kinds of network packets
- Asymetric paths and router support in the CM through netlink messages
- DMABUF importer support for mlx5devx umem's
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRRRCHOFoQz/8F5bUaFwuHvBreFYQUCYz9bgAAKCRCFwuHvBreF
YevoAP47J/svlOFlFtBhTVF79Ddtf+MMeqeVvLoHHQbCU5rUpAD+KUpTXAvwNcM9
dHwNXz9ctanP5397qusH0rxOKPo/EA4=
=lgSv
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"Not a big list of changes this cycle, mostly small things. The new
MANA rdma driver should come next cycle along with a bunch of work on
rxe.
Summary:
- Small bug fixes in mlx5, efa, rxe, hns, irdma, erdma, siw
- rts tracing improvements
- Code improvements: strlscpy conversion, unused parameter, spelling
mistakes, unused variables, flex arrays
- restrack device details report for hns
- Simplify struct device initialization in SRP
- Eliminate the never-used service_mask support in IB CM
- Make rxe not print to the console for some kinds of network packets
- Asymetric paths and router support in the CM through netlink
messages
- DMABUF importer support for mlx5devx umem's"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (84 commits)
RDMA/rxe: Remove error/warning messages from packet receiver path
RDMA/usnic: fix set-but-not-unused variable 'flags' warning
IB/hfi1: Use skb_put_data() instead of skb_put/memcpy pair
RDMA/hns: Unified Log Printing Style
RDMA/hns: Replacing magic number with macros in apply_func_caps()
RDMA/hns: Repacing 'dseg_len' by macros in fill_ext_sge_inl_data()
RDMA/hns: Remove redundant 'max_srq_desc_sz' in caps
RDMA/hns: Remove redundant 'num_mtt_segs' and 'max_extend_sg'
RDMA/hns: Remove redundant 'phy_addr' in hns_roce_hem_list_find_mtt()
RDMA/hns: Remove redundant 'use_lowmem' argument from hns_roce_init_hem_table()
RDMA/hns: Remove redundant 'bt_level' for hem_list_alloc_item()
RDMA/hns: Remove redundant 'attr_mask' in modify_qp_init_to_init()
RDMA/hns: Remove unnecessary brackets when getting point
RDMA/hns: Remove unnecessary braces for single statement blocks
RDMA/hns: Cleanup for a spelling error of Asynchronous
IB/rdmavt: Add __init/__exit annotations to module init/exit funcs
RDMA/rxe: Remove redundant num_sge fields
RDMA/mlx5: Enable ATS support for MRs and umems
RDMA/mlx5: Add support for dmabuf to devx umem
RDMA/core: Add UVERBS_ATTR_RAW_FD
...
-----BEGIN PGP SIGNATURE-----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=R05e
-----END PGP SIGNATURE-----
Merge tag 'for-6.1/block-2022-10-03' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe pull requests via Christoph:
- handle number of queue changes in the TCP and RDMA drivers
(Daniel Wagner)
- allow changing the number of queues in nvmet (Daniel Wagner)
- also consider host_iface when checking ip options (Daniel
Wagner)
- don't map pages which can't come from HIGHMEM (Fabio M. De
Francesco)
- avoid unnecessary flush bios in nvmet (Guixin Liu)
- shrink and better pack the nvme_iod structure (Keith Busch)
- add comment for unaligned "fake" nqn (Linjun Bao)
- print actual source IP address through sysfs "address" attr
(Martin Belanger)
- various cleanups (Jackie Liu, Wolfram Sang, Genjian Zhang)
- handle effects after freeing the request (Keith Busch)
- copy firmware_rev on each init (Keith Busch)
- restrict management ioctls to admin (Keith Busch)
- ensure subsystem reset is single threaded (Keith Busch)
- report the actual number of tagset maps in nvme-pci (Keith
Busch)
- small fabrics authentication fixups (Christoph Hellwig)
- add common code for tagset allocation and freeing (Christoph
Hellwig)
- stop using the request_queue in nvmet (Christoph Hellwig)
- set min_align_mask before calculating max_hw_sectors (Rishabh
Bhatnagar)
- send a rediscover uevent when a persistent discovery controller
reconnects (Sagi Grimberg)
- misc nvmet-tcp fixes (Varun Prakash, zhenwei pi)
- MD pull request via Song:
- Various raid5 fix and clean up, by Logan Gunthorpe and David
Sloan.
- Raid10 performance optimization, by Yu Kuai.
- sbitmap wakeup hang fixes (Hugh, Keith, Jan, Yu)
- IO scheduler switching quisce fix (Keith)
- s390/dasd block driver updates (Stefan)
- support for recovery for the ublk driver (ZiyangZhang)
- rnbd drivers fixes and updates (Guoqing, Santosh, ye, Christoph)
- blk-mq and null_blk map fixes (Bart)
- various bcache fixes (Coly, Jilin, Jules)
- nbd signal hang fix (Shigeru)
- block writeback throttling fix (Yu)
- optimize the passthrough mapping handling (me)
- prepare block cgroups to being gendisk based (Christoph)
- get rid of an old PSI hack in the block layer, moving it to the
callers instead where it belongs (Christoph)
- blk-throttle fixes and cleanups (Yu)
- misc fixes and cleanups (Liu Shixin, Liu Song, Miaohe, Pankaj,
Ping-Xiang, Wolfram, Saurabh, Li Jinlin, Li Lei, Lin, Li zeming,
Miaohe, Bart, Coly, Gaosheng
* tag 'for-6.1/block-2022-10-03' of git://git.kernel.dk/linux: (162 commits)
sbitmap: fix lockup while swapping
block: add rationale for not using blk_mq_plug() when applicable
block: adapt blk_mq_plug() to not plug for writes that require a zone lock
s390/dasd: use blk_mq_alloc_disk
blk-cgroup: don't update the blkg lookup hint in blkg_conf_prep
nvmet: don't look at the request_queue in nvmet_bdev_set_limits
nvmet: don't look at the request_queue in nvmet_bdev_zone_mgmt_emulate_all
blk-mq: use quiesced elevator switch when reinitializing queues
block: replace blk_queue_nowait with bdev_nowait
nvme: remove nvme_ctrl_init_connect_q
nvme-loop: use the tagset alloc/free helpers
nvme-loop: store the generic nvme_ctrl in set->driver_data
nvme-loop: initialize sqsize later
nvme-fc: use the tagset alloc/free helpers
nvme-fc: store the generic nvme_ctrl in set->driver_data
nvme-fc: keep ctrl->sqsize in sync with opts->queue_size
nvme-rdma: use the tagset alloc/free helpers
nvme-rdma: store the generic nvme_ctrl in set->driver_data
nvme-tcp: use the tagset alloc/free helpers
nvme-tcp: store the generic nvme_ctrl in set->driver_data
...
Support for the VIRTIO_BLK_F_SECURE_ERASE VirtIO feature.
A device that offers this feature can receive VIRTIO_BLK_T_SECURE_ERASE
commands.
A device which supports this feature has the following fields in the
virtio config:
- max_secure_erase_sectors
- max_secure_erase_seg
- secure_erase_sector_alignment
max_secure_erase_sectors and secure_erase_sector_alignment are expressed
in 512-byte units.
Every secure erase command has the following fields:
- sectors: The starting offset in 512-byte units.
- num_sectors: The number of sectors.
Signed-off-by: Alvaro Karsz <alvaro.karsz@solid-run.com>
Message-Id: <20220921082729.2516779-1-alvaro.karsz@solid-run.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Core
----
- Introduce and use a single page frag cache for allocating small skb
heads, clawing back the 10-20% performance regression in UDP flood
test from previous fixes.
- Run packets which already went thru HW coalescing thru SW GRO.
This significantly improves TCP segment coalescing and simplifies
deployments as different workloads benefit from HW or SW GRO.
- Shrink the size of the base zero-copy send structure.
- Move TCP init under a new slow / sleepable version of DO_ONCE().
BPF
---
- Add BPF-specific, any-context-safe memory allocator.
- Add helpers/kfuncs for PKCS#7 signature verification from BPF
programs.
- Define a new map type and related helpers for user space -> kernel
communication over a ring buffer (BPF_MAP_TYPE_USER_RINGBUF).
- Allow targeting BPF iterators to loop through resources of one
task/thread.
- Add ability to call selected destructive functions.
Expose crash_kexec() to allow BPF to trigger a kernel dump.
Use CAP_SYS_BOOT check on the loading process to judge permissions.
- Enable BPF to collect custom hierarchical cgroup stats efficiently
by integrating with the rstat framework.
- Support struct arguments for trampoline based programs.
Only structs with size <= 16B and x86 are supported.
- Invoke cgroup/connect{4,6} programs for unprivileged ICMP ping
sockets (instead of just TCP and UDP sockets).
- Add a helper for accessing CLOCK_TAI for time sensitive network
related programs.
- Support accessing network tunnel metadata's flags.
- Make TCP SYN ACK RTO tunable by BPF programs with TCP Fast Open.
- Add support for writing to Netfilter's nf_conn:mark.
Protocols
---------
- WiFi: more Extremely High Throughput (EHT) and Multi-Link
Operation (MLO) work (802.11be, WiFi 7).
- vsock: improve support for SO_RCVLOWAT.
- SMC: support SO_REUSEPORT.
- Netlink: define and document how to use netlink in a "modern" way.
Support reporting missing attributes via extended ACK.
- IPSec: support collect metadata mode for xfrm interfaces.
- TCPv6: send consistent autoflowlabel in SYN_RECV state
and RST packets.
- TCP: introduce optional per-netns connection hash table to allow
better isolation between namespaces (opt-in, at the cost of memory
and cache pressure).
- MPTCP: support TCP_FASTOPEN_CONNECT.
- Add NEXT-C-SID support in Segment Routing (SRv6) End behavior.
- Adjust IP_UNICAST_IF sockopt behavior for connected UDP sockets.
- Open vSwitch:
- Allow specifying ifindex of new interfaces.
- Allow conntrack and metering in non-initial user namespace.
- TLS: support the Korean ARIA-GCM crypto algorithm.
- Remove DECnet support.
Driver API
----------
- Allow selecting the conduit interface used by each port
in DSA switches, at runtime.
- Ethernet Power Sourcing Equipment and Power Device support.
- Add tc-taprio support for queueMaxSDU parameter, i.e. setting
per traffic class max frame size for time-based packet schedules.
- Support PHY rate matching - adapting between differing host-side
and link-side speeds.
- Introduce QUSGMII PHY mode and 1000BASE-KX interface mode.
- Validate OF (device tree) nodes for DSA shared ports; make
phylink-related properties mandatory on DSA and CPU ports.
Enforcing more uniformity should allow transitioning to phylink.
- Require that flash component name used during update matches one
of the components for which version is reported by info_get().
- Remove "weight" argument from driver-facing NAPI API as much
as possible. It's one of those magic knobs which seemed like
a good idea at the time but is too indirect to use in practice.
- Support offload of TLS connections with 256 bit keys.
New hardware / drivers
----------------------
- Ethernet:
- Microchip KSZ9896 6-port Gigabit Ethernet Switch
- Renesas Ethernet AVB (EtherAVB-IF) Gen4 SoCs
- Analog Devices ADIN1110 and ADIN2111 industrial single pair
Ethernet (10BASE-T1L) MAC+PHY.
- Rockchip RV1126 Gigabit Ethernet (a version of stmmac IP).
- Ethernet SFPs / modules:
- RollBall / Hilink / Turris 10G copper SFPs
- HALNy GPON module
- WiFi:
- CYW43439 SDIO chipset (brcmfmac)
- CYW89459 PCIe chipset (brcmfmac)
- BCM4378 on Apple platforms (brcmfmac)
Drivers
-------
- CAN:
- gs_usb: HW timestamp support
- Ethernet PHYs:
- lan8814: cable diagnostics
- Ethernet NICs:
- Intel (100G):
- implement control of FCS/CRC stripping
- port splitting via devlink
- L2TPv3 filtering offload
- nVidia/Mellanox:
- tunnel offload for sub-functions
- MACSec offload, w/ Extended packet number and replay
window offload
- significantly restructure, and optimize the AF_XDP support,
align the behavior with other vendors
- Huawei:
- configuring DSCP map for traffic class selection
- querying standard FEC statistics
- querying SerDes lane number via ethtool
- Marvell/Cavium:
- egress priority flow control
- MACSec offload
- AMD/SolarFlare:
- PTP over IPv6 and raw Ethernet
- small / embedded:
- ax88772: convert to phylink (to support SFP cages)
- altera: tse: convert to phylink
- ftgmac100: support fixed link
- enetc: standard Ethtool counters
- macb: ZynqMP SGMII dynamic configuration support
- tsnep: support multi-queue and use page pool
- lan743x: Rx IP & TCP checksum offload
- igc: add xdp frags support to ndo_xdp_xmit
- Ethernet high-speed switches:
- Marvell (prestera):
- support SPAN port features (traffic mirroring)
- nexthop object offloading
- Microchip (sparx5):
- multicast forwarding offload
- QoS queuing offload (tc-mqprio, tc-tbf, tc-ets)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- support RGMII cmode
- NXP (felix):
- standardized ethtool counters
- Microchip (lan966x):
- QoS queuing offload (tc-mqprio, tc-tbf, tc-cbs, tc-ets)
- traffic policing and mirroring
- link aggregation / bonding offload
- QUSGMII PHY mode support
- Qualcomm 802.11ax WiFi (ath11k):
- cold boot calibration support on WCN6750
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- Wake-on-WLAN support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
- MediaTek WiFi (mt76):
- WiFi-to-Ethernet bridging offload for MT7986 chips
- RealTek WiFi (rtw89):
- P2P support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Gsio
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Introduce and use a single page frag cache for allocating small skb
heads, clawing back the 10-20% performance regression in UDP flood
test from previous fixes.
- Run packets which already went thru HW coalescing thru SW GRO. This
significantly improves TCP segment coalescing and simplifies
deployments as different workloads benefit from HW or SW GRO.
- Shrink the size of the base zero-copy send structure.
- Move TCP init under a new slow / sleepable version of DO_ONCE().
BPF:
- Add BPF-specific, any-context-safe memory allocator.
- Add helpers/kfuncs for PKCS#7 signature verification from BPF
programs.
- Define a new map type and related helpers for user space -> kernel
communication over a ring buffer (BPF_MAP_TYPE_USER_RINGBUF).
- Allow targeting BPF iterators to loop through resources of one
task/thread.
- Add ability to call selected destructive functions. Expose
crash_kexec() to allow BPF to trigger a kernel dump. Use
CAP_SYS_BOOT check on the loading process to judge permissions.
- Enable BPF to collect custom hierarchical cgroup stats efficiently
by integrating with the rstat framework.
- Support struct arguments for trampoline based programs. Only
structs with size <= 16B and x86 are supported.
- Invoke cgroup/connect{4,6} programs for unprivileged ICMP ping
sockets (instead of just TCP and UDP sockets).
- Add a helper for accessing CLOCK_TAI for time sensitive network
related programs.
- Support accessing network tunnel metadata's flags.
- Make TCP SYN ACK RTO tunable by BPF programs with TCP Fast Open.
- Add support for writing to Netfilter's nf_conn:mark.
Protocols:
- WiFi: more Extremely High Throughput (EHT) and Multi-Link Operation
(MLO) work (802.11be, WiFi 7).
- vsock: improve support for SO_RCVLOWAT.
- SMC: support SO_REUSEPORT.
- Netlink: define and document how to use netlink in a "modern" way.
Support reporting missing attributes via extended ACK.
- IPSec: support collect metadata mode for xfrm interfaces.
- TCPv6: send consistent autoflowlabel in SYN_RECV state and RST
packets.
- TCP: introduce optional per-netns connection hash table to allow
better isolation between namespaces (opt-in, at the cost of memory
and cache pressure).
- MPTCP: support TCP_FASTOPEN_CONNECT.
- Add NEXT-C-SID support in Segment Routing (SRv6) End behavior.
- Adjust IP_UNICAST_IF sockopt behavior for connected UDP sockets.
- Open vSwitch:
- Allow specifying ifindex of new interfaces.
- Allow conntrack and metering in non-initial user namespace.
- TLS: support the Korean ARIA-GCM crypto algorithm.
- Remove DECnet support.
Driver API:
- Allow selecting the conduit interface used by each port in DSA
switches, at runtime.
- Ethernet Power Sourcing Equipment and Power Device support.
- Add tc-taprio support for queueMaxSDU parameter, i.e. setting per
traffic class max frame size for time-based packet schedules.
- Support PHY rate matching - adapting between differing host-side
and link-side speeds.
- Introduce QUSGMII PHY mode and 1000BASE-KX interface mode.
- Validate OF (device tree) nodes for DSA shared ports; make
phylink-related properties mandatory on DSA and CPU ports.
Enforcing more uniformity should allow transitioning to phylink.
- Require that flash component name used during update matches one of
the components for which version is reported by info_get().
- Remove "weight" argument from driver-facing NAPI API as much as
possible. It's one of those magic knobs which seemed like a good
idea at the time but is too indirect to use in practice.
- Support offload of TLS connections with 256 bit keys.
New hardware / drivers:
- Ethernet:
- Microchip KSZ9896 6-port Gigabit Ethernet Switch
- Renesas Ethernet AVB (EtherAVB-IF) Gen4 SoCs
- Analog Devices ADIN1110 and ADIN2111 industrial single pair
Ethernet (10BASE-T1L) MAC+PHY.
- Rockchip RV1126 Gigabit Ethernet (a version of stmmac IP).
- Ethernet SFPs / modules:
- RollBall / Hilink / Turris 10G copper SFPs
- HALNy GPON module
- WiFi:
- CYW43439 SDIO chipset (brcmfmac)
- CYW89459 PCIe chipset (brcmfmac)
- BCM4378 on Apple platforms (brcmfmac)
Drivers:
- CAN:
- gs_usb: HW timestamp support
- Ethernet PHYs:
- lan8814: cable diagnostics
- Ethernet NICs:
- Intel (100G):
- implement control of FCS/CRC stripping
- port splitting via devlink
- L2TPv3 filtering offload
- nVidia/Mellanox:
- tunnel offload for sub-functions
- MACSec offload, w/ Extended packet number and replay window
offload
- significantly restructure, and optimize the AF_XDP support,
align the behavior with other vendors
- Huawei:
- configuring DSCP map for traffic class selection
- querying standard FEC statistics
- querying SerDes lane number via ethtool
- Marvell/Cavium:
- egress priority flow control
- MACSec offload
- AMD/SolarFlare:
- PTP over IPv6 and raw Ethernet
- small / embedded:
- ax88772: convert to phylink (to support SFP cages)
- altera: tse: convert to phylink
- ftgmac100: support fixed link
- enetc: standard Ethtool counters
- macb: ZynqMP SGMII dynamic configuration support
- tsnep: support multi-queue and use page pool
- lan743x: Rx IP & TCP checksum offload
- igc: add xdp frags support to ndo_xdp_xmit
- Ethernet high-speed switches:
- Marvell (prestera):
- support SPAN port features (traffic mirroring)
- nexthop object offloading
- Microchip (sparx5):
- multicast forwarding offload
- QoS queuing offload (tc-mqprio, tc-tbf, tc-ets)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- support RGMII cmode
- NXP (felix):
- standardized ethtool counters
- Microchip (lan966x):
- QoS queuing offload (tc-mqprio, tc-tbf, tc-cbs, tc-ets)
- traffic policing and mirroring
- link aggregation / bonding offload
- QUSGMII PHY mode support
- Qualcomm 802.11ax WiFi (ath11k):
- cold boot calibration support on WCN6750
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- Wake-on-WLAN support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
- MediaTek WiFi (mt76):
- WiFi-to-Ethernet bridging offload for MT7986 chips
- RealTek WiFi (rtw89):
- P2P support"
* tag 'net-next-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1864 commits)
eth: pse: add missing static inlines
once: rename _SLOW to _SLEEPABLE
net: pse-pd: add regulator based PSE driver
dt-bindings: net: pse-dt: add bindings for regulator based PoDL PSE controller
ethtool: add interface to interact with Ethernet Power Equipment
net: mdiobus: search for PSE nodes by parsing PHY nodes.
net: mdiobus: fwnode_mdiobus_register_phy() rework error handling
net: add framework to support Ethernet PSE and PDs devices
dt-bindings: net: phy: add PoDL PSE property
net: marvell: prestera: Propagate nh state from hw to kernel
net: marvell: prestera: Add neighbour cache accounting
net: marvell: prestera: add stub handler neighbour events
net: marvell: prestera: Add heplers to interact with fib_notifier_info
net: marvell: prestera: Add length macros for prestera_ip_addr
net: marvell: prestera: add delayed wq and flush wq on deinit
net: marvell: prestera: Add strict cleanup of fib arbiter
net: marvell: prestera: Add cleanup of allocated fib_nodes
net: marvell: prestera: Add router nexthops ABI
eth: octeon: fix build after netif_napi_add() changes
net/mlx5: E-Switch, Return EBUSY if can't get mode lock
...
zram_table_entry::flags stores object size in the lower bits and zram
pageflags in the upper bits. However, for some reason, we use 24 lower
bits, while maximum zram object size is PAGE_SIZE, which requires
PAGE_SHIFT bits (up to 16 on arm64). This wastes 24 - PAGE_SHIFT bits
that we can use for additional zram pageflags instead.
Also add a BUILD_BUG_ON() to alert us should we run out of bits in
zram_table_entry::flags.
Link: https://lkml.kernel.org/r/20220912152744.527438-1-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Brian Geffon <bgeffon@google.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
START_USER_RECOVERY and END_USER_RECOVERY are two new control commands
to support user recovery feature.
After a crash, user should send START_USER_RECOVERY, it will:
(1) check if (a)current ublk_device is UBLK_S_DEV_QUIESCED which was
set by quiesce_work and (b)chardev is released
(2) reinit all ubqs, including:
(a) put the task_struct and reset ->ubq_daemon to NULL.
(b) reset all ublk_io.
(3) reset ub->mm to NULL.
Then, user should start a new process and send FETCH_REQ on each
ubq_daemon.
Finally, user should send END_USER_RECOVERY, it will:
(1) wait for all new ubq_daemons getting ready.
(2) update ublksrv_pid
(3) unquiesce the request queue and expect incoming ublk_queue_rq()
(4) convert ub's state to UBLK_S_DEV_LIVE
Note: we can handle STOP_DEV between START_USER_RECOVERY and
END_USER_RECOVERY. This is helpful to users who cannot start new process
after sending START_USER_RECOVERY ctrl-cmd.
Signed-off-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220923153919.44078-7-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
UBLK_F_USER_RECOVERY_REISSUE implies that:
With a dying ubq_daemon, ublk_drv let monitor_work requeues rq issued to
userspace(ublksrv) before the ubq_daemon is dying.
UBLK_F_USER_RECOVERY_REISSUE is designed for backends which:
(1) tolerate double-write since ublk_drv may issue the same rq
twice.
(2) does not let frontend users get I/O error, such as read-only FS
and VM backend.
Signed-off-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220923153919.44078-6-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With USER_RECOVERY feature enabled, the monitor_work schedules
quiesce_work after finding a dying ubq_daemon. The monitor_work
should also abort all rqs issued to userspace before the ubq_daemon is
dying. The quiesce_work's job is to:
(1) quiesce request queue.
(2) check if there is any INFLIGHT rq. If so, we retry until all these
rqs are requeued and become IDLE. These rqs should be requeued by
ublk_queue_rq(), task work, io_uring fallback wq or monitor_work.
(3) complete all ioucmds by calling io_uring_cmd_done(). We are safe to
do so because no ioucmd can be referenced now.
(5) set ub's state to UBLK_S_DEV_QUIESCED, which means we are ready for
recovery. This state is exposed to userspace by GET_DEV_INFO.
The driver can always handle STOP_DEV and cleanup everything no matter
ub's state is LIVE or QUIESCED. After ub's state is UBLK_S_DEV_QUIESCED,
user can recover with new process.
Note: we do not change the default behavior with reocvery feature
disabled. monitor_work still schedules stop_work and abort inflight
rqs. And finally ublk_device is released.
Signed-off-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220923153919.44078-5-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With recovery feature enabled, in ublk_queue_rq or task work
(in exit_task_work or fallback wq), we requeue rqs instead of
ending(aborting) them. Besides, No matter recovery feature is enabled
or disabled, we schedule monitor_work immediately.
Signed-off-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220923153919.44078-4-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Define some macros for recovery feature.
UBLK_S_DEV_QUIESCED implies that ublk_device is quiesced
and is ready for recovery. This state can be observed by userspace.
UBLK_F_USER_RECOVERY implies that:
(1) ublk_drv enables recovery feature. It won't let monitor_work to
automatically abort rqs and release the device.
(2) With a dying ubq_daemon, ublk_drv ends(aborts) rqs issued to
userspace(ublksrv) before crash.
(3) With a dying ubq_daemon, in task work and ublk_queue_rq(),
ublk_drv requeues rqs.
Signed-off-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220923153919.44078-3-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This check is not atomic. So with recovery feature, ubq_daemon may be
modified simultaneously by recovery task. Instead, check 'current' is
safe here because 'current' never changes.
Also add comment explaining this check, which is really important for
understanding recovery feature.
Signed-off-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220923153919.44078-2-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All implementations of req->collision, _req_may_be_done and
drbd_fail_pending_reads have been removed, so remove the comments
in receive_DataReply() that provide no useful information.
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Acked-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20220920015216.782190-3-cuigaosheng1@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The _req_may_be_done() has been removed by
commit 6870ca6d46 ("drbd: factor out master_bio completion
and drbd_request destruction paths"), so remove the orphan
declaration.
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Acked-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20220920015216.782190-2-cuigaosheng1@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Given that rnbd_srv_sess_dev already has an open_flags member, there
is no need for the rnbd_dev indirection as a simple block_device pointer
works just as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20220909131509.3263924-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
These can be trivially open coded in the callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20220909131509.3263924-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fold rnbd_endio into the only caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20220909131509.3263924-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove all the wrappers and just get the information directly from
the block device, or where no such helpers exist the request_queue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20220909131509.3263924-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
w_start_resync has been removed since
commit ac0acb9e39 ("drbd: use drbd_device_post_work()
in more places"), so remove it.
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Acked-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It doesn't make sense for us to retry to compress an uncompressible page
(comp_len == PAGE_SIZE) in zsmalloc slowpath, because we will be storing
it uncompressed anyway. We can avoid wasting time on another compression
attempt. It is enough to take lock (zcomp_stream_get) and execute the
code below.
Link: https://lkml.kernel.org/r/20220824113117.78849-1-avromanov@sberdevices.ru
Signed-off-by: Alexey Romanov <avromanov@sberdevices.ru>
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Alexey Romanov <avromanov@sberdevices.ru>
Cc: Dmitry Rokosov <DDRokosov@sberdevices.ru>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We do all reset operations under write lock, so we don't need to save
->disksize and ->comp to stack variables. Another thing is that ->comp is
freed during zram reset, but comp pointer is not NULL-ed, so zram keeps
the freed pointer value.
Link: https://lkml.kernel.org/r/20220824035100.971816-1-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
syzbot reported hung task [1]. The following program is a simplified
version of the reproducer:
int main(void)
{
int sv[2], fd;
if (socketpair(AF_UNIX, SOCK_STREAM, 0, sv) < 0)
return 1;
if ((fd = open("/dev/nbd0", 0)) < 0)
return 1;
if (ioctl(fd, NBD_SET_SIZE_BLOCKS, 0x81) < 0)
return 1;
if (ioctl(fd, NBD_SET_SOCK, sv[0]) < 0)
return 1;
if (ioctl(fd, NBD_DO_IT) < 0)
return 1;
return 0;
}
When signal interrupt nbd_start_device_ioctl() waiting the condition
atomic_read(&config->recv_threads) == 0, the task can hung because it
waits the completion of the inflight IOs.
This patch fixes the issue by clearing queue, not just shutdown, when
signal interrupt nbd_start_device_ioctl().
Link: https://syzkaller.appspot.com/bug?id=7d89a3ffacd2b83fdd39549bc4d8e0a89ef21239 [1]
Reported-by: syzbot+38e6c55d4969a14c1534@syzkaller.appspotmail.com
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20220907163502.577561-1-syoshida@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It is not necessary since it is set later just before function
return success.
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Acked-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Link: https://lore.kernel.org/r/20220902100055.25724-4-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Change the return type to void given it always returns 0.
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Acked-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Link: https://lore.kernel.org/r/20220902100055.25724-3-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Let's add some explanations here given the err handling is not obvious.
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Acked-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Link: https://lore.kernel.org/r/20220902100055.25724-2-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYxNpQQAKCRCAXGG7T9hj
vgO9AQChV9kknjgoL9qWJe25nNHyQ4zNfgtUNLefamYOAr93HgEAiFv7SIwMshFb
jl4oceI76z2u6APkZlySR2JcJa+B+go=
=BtBW
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.0-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- a minor fix for the Xen grant driver
- a small series fixing a recently introduced problem in the Xen
blkfront/blkback drivers with negotiation of feature usage
* tag 'for-linus-6.0-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/grants: prevent integer overflow in gnttab_dma_alloc_pages()
xen-blkfront: Cache feature_persistent value before advertisement
xen-blkfront: Advertise feature-persistent as user requested
xen-blkback: Advertise feature-persistent as user requested
Xen blkfront advertises its support of the persistent grants feature
when it first setting up and when resuming in 'talk_to_blkback()'.
Then, blkback reads the advertised value when it connects with blkfront
and decides if it will use the persistent grants feature or not, and
advertises its decision to blkfront. Blkfront reads the blkback's
decision and it also makes the decision for the use of the feature.
Commit 402c43ea6b ("xen-blkfront: Apply 'feature_persistent' parameter
when connect"), however, made the blkfront's read of the parameter for
disabling the advertisement, namely 'feature_persistent', to be done
when it negotiate, not when advertise. Therefore blkfront advertises
without reading the parameter. As the field for caching the parameter
value is zero-initialized, it always advertises as the feature is
disabled, so that the persistent grants feature becomes always disabled.
This commit fixes the issue by making the blkfront does parmeter caching
just before the advertisement.
Fixes: 402c43ea6b ("xen-blkfront: Apply 'feature_persistent' parameter when connect")
Cc: <stable@vger.kernel.org> # 5.10.x
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: SeongJae Park <sj@kernel.org>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220831165824.94815-4-sj@kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
The advertisement of the persistent grants feature (writing
'feature-persistent' to xenbus) should mean not the decision for using
the feature but only the availability of the feature. However, commit
74a852479c ("xen-blkfront: add a parameter for disabling of persistent
grants") made a field of blkfront, which was a place for saving only the
negotiation result, to be used for yet another purpose: caching of the
'feature_persistent' parameter value. As a result, the advertisement,
which should follow only the parameter value, becomes inconsistent.
This commit fixes the misuse of the semantic by making blkfront saves
the parameter value in a separate place and advertises the support based
on only the saved value.
Fixes: 74a852479c ("xen-blkfront: add a parameter for disabling of persistent grants")
Cc: <stable@vger.kernel.org> # 5.10.x
Suggested-by: Juergen Gross <jgross@suse.com>
Signed-off-by: SeongJae Park <sj@kernel.org>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220831165824.94815-3-sj@kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
The advertisement of the persistent grants feature (writing
'feature-persistent' to xenbus) should mean not the decision for using
the feature but only the availability of the feature. However, commit
aac8a70db2 ("xen-blkback: add a parameter for disabling of persistent
grants") made a field of blkback, which was a place for saving only the
negotiation result, to be used for yet another purpose: caching of the
'feature_persistent' parameter value. As a result, the advertisement,
which should follow only the parameter value, becomes inconsistent.
This commit fixes the misuse of the semantic by making blkback saves the
parameter value in a separate place and advertises the support based on
only the saved value.
Fixes: aac8a70db2 ("xen-blkback: add a parameter for disabling of persistent grants")
Cc: <stable@vger.kernel.org> # 5.10.x
Suggested-by: Juergen Gross <jgross@suse.com>
Signed-off-by: SeongJae Park <sj@kernel.org>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220831165824.94815-2-sj@kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Since process_{read,write} already prints direction info if ctx->ops.rdma_ev
fails, no need to pass 'dir'.
Link: https://lore.kernel.org/r/20220826081117.21687-1-guoqing.jiang@linux.dev
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
We had historically not checked that genlmsghdr.reserved
is 0 on input which prevents us from using those precious
bytes in the future.
One use case would be to extend the cmd field, which is
currently just 8 bits wide and 256 is not a lot of commands
for some core families.
To make sure that new families do the right thing by default
put the onus of opting out of validation on existing families.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paul Moore <paul@paul-moore.com> (NetLabel)
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAmMI9VgQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpgY+D/0axaG4MQODNSCyzTkKdFJqeL1Ab6tgz+SP
w4hqGhBA50P18nqQo14v/l2wBnc3DnvX6OcoAj2v+27WRw4VAC6pYu9cHiiz0sK0
WyfYE/3qdB5PTe3149UcMd0BlPzMiadYKYhDbS5zLq5VGnun4oOT6uJugdz5toSl
GgPJ4zQTjUE/w7pJ40fSTZ82FPCqVndBaSMycLvzzAkzfKdMxMIPBqFTDdW/gFqG
1Xc7NI4vASw8jsrG+TkPESNf4j0WcEs8+zCV9d9WFSQjWgktV1NpdCZ9CA+jD0cV
h0i31SB43pttZZTARPraPgQdC23L22CpxxNTuzwz5ZKAuSulML87S/W2lN7HnagQ
GAl6irQdB9RXN5o6vmOXkZIfmfuTctrXay7g13tNk/WUrGb/3euk4CJMYJWA4fM7
VkUS3yCjvP5z8auqOqti7zEy1QSN8mvdtsafU1n+tsf0WdIIqH+sufSnmJExbOs9
gzL2xcabOFCD5WYDCpl/SkbnY4G7Qrk4oHIB9S/r0aOKVHFdQ8JMp3GBVjSlHulN
Nz3oScNQBG3CSvJ2QbFi6UQxt6YSs+tx/oa1plmeCe4w9tModooL0CdfmKMBwPXT
AGlHvUIGyl4ZT/XamQ19AdFOE7WLHPG7wYtZUaFiNtkjAsgMoQr2bwYeTpb29Cfu
881BssmWCQ==
=qR5N
-----END PGP SIGNATURE-----
Merge tag 'block-6.0-2022-08-26' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- MD pull request via Song:
- Fix for clustered raid (Guoqing Jiang)
- req_op fix (Bart Van Assche)
- Fix race condition in raid recreate (David Sloan)
- loop configuration overflow fix (Siddh)
- Fix missing commit_rqs call for certain conditions (Yu)
* tag 'block-6.0-2022-08-26' of git://git.kernel.dk/linux-block:
md: call __md_stop_writes in md_stop
Revert "md-raid: destroy the bitmap after destroying the thread"
md: Flush workqueue md_rdev_misc_wq in md_alloc()
md/raid10: Fix the data type of an r10_sync_page_io() argument
loop: Check for overflow while configuring loop
blk-mq: fix io hung due to missing commit_rqs
Return the value from rtrs_clt_rdma_cq_direct() directly instead of
storing it in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20220824075213.221397-1-ye.xingchen@zte.com.cn
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The userspace can configure a loop using an ioctl call, wherein
a configuration of type loop_config is passed (see lo_ioctl()'s
case on line 1550 of drivers/block/loop.c). This proceeds to call
loop_configure() which in turn calls loop_set_status_from_info()
(see line 1050 of loop.c), passing &config->info which is of type
loop_info64*. This function then sets the appropriate values, like
the offset.
loop_device has lo_offset of type loff_t (see line 52 of loop.c),
which is typdef-chained to long long, whereas loop_info64 has
lo_offset of type __u64 (see line 56 of include/uapi/linux/loop.h).
The function directly copies offset from info to the device as
follows (See line 980 of loop.c):
lo->lo_offset = info->lo_offset;
This results in an overflow, which triggers a warning in iomap_iter()
due to a call to iomap_iter_done() which has:
WARN_ON_ONCE(iter->iomap.offset > iter->pos);
Thus, check for negative value during loop_set_status_from_info().
Bug report: https://syzkaller.appspot.com/bug?id=c620fe14aac810396d3c3edc9ad73848bf69a29e
Reported-and-tested-by: syzbot+a8e049cd3abd342936b6@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Siddh Raman Pant <code@siddh.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220823160810.181275-1-code@siddh.me
Signed-off-by: Jens Axboe <axboe@kernel.dk>
remainder fix up the changes which went into this -rc cycle.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCYwQZcgAKCRDdBJ7gKXxA
jnCxAQCk8L6PPm0L2KvKr5Vu3M/T0o9SvfxfM5yho80zM68fHQD/eLxz+nd3m+N5
K7Mdbcb2u6F46qQaS+S5RialEWKpsw8=
=WtBo
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2022-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"Thirteen fixes, almost all for MM.
Seven of these are cc:stable and the remainder fix up the changes
which went into this -rc cycle"
* tag 'mm-hotfixes-stable-2022-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
kprobes: don't call disarm_kprobe() for disabled kprobes
mm/shmem: shmem_replace_page() remember NR_SHMEM
mm/shmem: tmpfs fallocate use file_modified()
mm/shmem: fix chattr fsflags support in tmpfs
mm/hugetlb: support write-faults in shared mappings
mm/hugetlb: fix hugetlb not supporting softdirty tracking
mm/uffd: reset write protection when unregister with wp-mode
mm/smaps: don't access young/dirty bit if pte unpresent
mm: add DEVICE_ZONE to FOR_ALL_ZONES
kernel/sys_ni: add compat entry for fadvise64_64
mm/gup: fix FOLL_FORCE COW security issue and remove FOLL_COW
Revert "zram: remove double compression logic"
get_maintainer: add Alan to .get_maintainer.ignore
Since blk_mq_map_queues() and the .map_queues() callbacks always return 0,
change their return type into void. Most callers ignore the returned value
anyway.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Acked-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Link: https://lore.kernel.org/r/20220815170043.19489-3-bvanassche@acm.org
[axboe: fold in fix from Bart]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of returning -EINVAL if an internal inconsistency is detected,
fall back to a single submission queue. This patch prepares for changing
the return value of the .map_queues() callbacks into void.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20220815170043.19489-2-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add event tracing mechanism for following routines:
- create_sess()
- destroy_sess()
- process_rdma()
- process_msg_sess_info()
- process_msg_open()
- process_msg_close()
How to use:
1. Load the rnbd_server module
2. cd /sys/kernel/debug/tracing
3. If all the events need to be enabled:
echo 1 > events/rnbd_srv/enable
4. OR only speific routine/event needs to be enabled e.g.
echo 1 > events/rnbd_srv/create_sess/enable
5. cat trace
5. Run some workload which can trigger create_sess() routine/event
Signed-off-by: Santosh Pradhan <santosh.pradhan@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Link: https://lore.kernel.org/r/20220818105551.110490-2-haris.iqbal@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This reverts commit e7be8d1dd9 ("zram: remove double compression
logic") as it causes zram failures. It does not revert cleanly, PTR_ERR
handling was introduced in the meantime. This is handled by appropriate
IS_ERR.
When under memory pressure, zs_malloc() can fail. Before the above
commit, the allocation was retried with direct reclaim enabled (GFP_NOIO).
After the commit, it is not -- only __GFP_KSWAPD_RECLAIM is tried.
So when the failure occurs under memory pressure, the overlaying
filesystem such as ext2 (mounted by ext4 module in this case) can emit
failures, making the (file)system unusable:
EXT4-fs warning (device zram0): ext4_end_bio:343: I/O error 10 writing to inode 16386 starting block 159744)
Buffer I/O error on device zram0, logical block 159744
With direct reclaim, memory is really reclaimed and allocation succeeds,
eventually. In the worst case, the oom killer is invoked, which is proper
outcome if user sets up zram too large (in comparison to available RAM).
This very diff doesn't apply to 5.19 (stable) cleanly (see PTR_ERR note
above). Use revert of e7be8d1dd9 directly.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1202203
Link: https://lkml.kernel.org/r/20220810070609.14402-1-jslaby@suse.cz
Fixes: e7be8d1dd9 ("zram: remove double compression logic")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Alexey Romanov <avromanov@sberdevices.ru>
Cc: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Cc: Lukas Czerner <lczerner@redhat.com>
Cc: <stable@vger.kernel.org> [5.19]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=y2HE
-----END PGP SIGNATURE-----
Merge tag 'block-6.0-2022-08-19' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A few fixes that should go into this release:
- Small series of patches for ublk (ZiyangZhang)
- Remove dead function (Yu)
- Fix for running a block queue in case of resource starvation
(Yufen)"
* tag 'block-6.0-2022-08-19' of git://git.kernel.dk/linux-block:
blk-mq: run queue no matter whether the request is the last request
blk-mq: remove unused function blk_mq_queue_stopped()
ublk_drv: do not add a re-issued request aborted previously to ioucmd's task_work
ublk_drv: update comment for __ublk_fail_req()
ublk_drv: check ubq_daemon_is_dying() in __ublk_rq_task_work()
ublk_drv: update iod->addr for UBLK_IO_NEED_GET_DATA
In ublk_queue_rq(), Assume current request is a re-issued request aborted
previously in monitor_work because the ubq_daemon(ioucmd's task) is
PF_EXITING. For this request, we cannot call
io_uring_cmd_complete_in_task() anymore because at that moment io_uring
context may be freed in case that no inflight ioucmd exists. Otherwise,
we may cause null-deref in ctx->fallback_work.
Add a check on UBLK_IO_FLAG_ABORTED to prevent the above situation. This
check is safe and makes sense.
Note: monitor_work sets UBLK_IO_FLAG_ABORTED and ends this request
(releasing the tag). Then the request is restarted(allocating the tag)
and we are here. Since releasing/allocating a tag implies smp_mb(),
finding UBLK_IO_FLAG_ABORTED guarantees that here is a re-issued request
aborted previously.
Suggested-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220815023633.259825-4-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since __ublk_rq_task_work always fails requests immediately during
exiting, __ublk_fail_req() is only called from abort context during
exiting. So lock is unnecessary.
Signed-off-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220815023633.259825-3-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace direct check on PF_EXITING in __ublk_rq_task_work() by the
existing wrapper. Also inline ubq_daemon_is_dying().
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220815023633.259825-2-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYvi0yQAKCRCAXGG7T9hj
vmikAQDWSrcWuxDkGnzut0A1tBQRUCWDMyKPqigWAA5tH2sPgAEAtWfBvT1xyl7T
gZ22I7o21WxxDGyvNUcA65pK7c2cpg8=
=UMbq
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- fix the handling of the "persistent grants" feature negotiation
between Xen blkfront and Xen blkback drivers
- a cleanup of xen.config and adding xen.config to Xen section in
MAINTAINERS
- support HVMOP_set_evtchn_upcall_vector, which is more compliant to
"normal" interrupt handling than the global callback used up to now
- further small cleanups
* tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
MAINTAINERS: add xen config fragments to XEN HYPERVISOR sections
xen: remove XEN_SCRUB_PAGES in xen.config
xen/pciback: Fix comment typo
xen/xenbus: fix return type in xenbus_file_read()
xen-blkfront: Apply 'feature_persistent' parameter when connect
xen-blkback: Apply 'feature_persistent' parameter when connect
xen-blkback: fix persistent grants negotiation
x86/xen: Add support for HVMOP_set_evtchn_upcall_vector
If ublksrv sends UBLK_IO_NEED_GET_DATA with new allocated io buffer, we
have to update iod->addr in task_work before calling io_uring_cmd_done().
Then usersapce target can handle (write)io request with the new io
buffer reading from updated iod.
Without this change, userspace target may touch a wrong io buffer!
Signed-off-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220810055212.66417-1-ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A huge patchset supporting vq resize using the
new vq reset capability.
Features, fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmL2F9APHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRp00QIAKpxyu+zCtrdDuh68DsNn1Cu0y0PXG336ySy
MA1ck/bv94MZBIbI/Bnn3T1jDmUqTFHJiwaGz/aZ5gGAplZiejhH5Ds3SYjHckaa
MKeJ4FTXin9RESP+bXhv4BgZ+ju3KHHkf1jw3TAdVKQ7Nma1u4E6f8nprYEi0TI0
7gLUYenqzS7X1+v9O3rEvPr7tSbAKXYGYpV82sSjHIb9YPQx5luX1JJIZade8A25
mTt5hG1dP1ugUm1NEBPQHjSvdrvO3L5Ahy0My2Bkd77+tOlNF4cuMPt2NS/6+Pgd
n6oMt3GXqVvw5RxZyY8dpknH5kofZhjgFyZXH0l+aNItfHUs7t0=
=rIo2
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
- A huge patchset supporting vq resize using the new vq reset
capability
- Features, fixes, and cleanups all over the place
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (88 commits)
vdpa/mlx5: Fix possible uninitialized return value
vdpa_sim_blk: add support for discard and write-zeroes
vdpa_sim_blk: add support for VIRTIO_BLK_T_FLUSH
vdpa_sim_blk: make vdpasim_blk_check_range usable by other requests
vdpa_sim_blk: check if sector is 0 for commands other than read or write
vdpa_sim: Implement suspend vdpa op
vhost-vdpa: uAPI to suspend the device
vhost-vdpa: introduce SUSPEND backend feature bit
vdpa: Add suspend operation
virtio-blk: Avoid use-after-free on suspend/resume
virtio_vdpa: support the arg sizes of find_vqs()
vhost-vdpa: Call ida_simple_remove() when failed
vDPA: fix 'cast to restricted le16' warnings in vdpa.c
vDPA: !FEATURES_OK should not block querying device config space
vDPA/ifcvf: support userspace to query features and MQ of a management device
vDPA/ifcvf: get_config_size should return a value no greater than dev implementation
vhost scsi: Allow user to control num virtqueues
vhost-scsi: Fix max number of virtqueues
vdpa/mlx5: Support different address spaces for control and data
vdpa/mlx5: Implement susupend virtqueue callback
...
In some use cases[1], the backend is created while the frontend doesn't
support the persistent grants feature, but later the frontend can be
changed to support the feature and reconnect. In the past, 'blkback'
enabled the persistent grants feature since it unconditionally checked
if frontend supports the persistent grants feature for every connect
('connect_ring()') and decided whether it should use persistent grans or
not.
However, commit aac8a70db2 ("xen-blkback: add a parameter for
disabling of persistent grants") has mistakenly changed the behavior.
It made the frontend feature support check to not be repeated once it
shown the 'feature_persistent' as 'false', or the frontend doesn't
support persistent grants.
Similar behavioral change has made on 'blkfront' by commit 74a852479c
("xen-blkfront: add a parameter for disabling of persistent grants").
This commit changes the behavior of the parameter to make effect for
every connect, so that the previous behavior of 'blkfront' can be
restored.
[1] https://lore.kernel.org/xen-devel/CAJwUmVB6H3iTs-C+U=v-pwJB7-_ZRHPxHzKRJZ22xEPW7z8a=g@mail.gmail.com/
Fixes: 74a852479c ("xen-blkfront: add a parameter for disabling of persistent grants")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: SeongJae Park <sj@kernel.org>
Reviewed-by: Maximilian Heyne <mheyne@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220715225108.193398-4-sj@kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
In some use cases[1], the backend is created while the frontend doesn't
support the persistent grants feature, but later the frontend can be
changed to support the feature and reconnect. In the past, 'blkback'
enabled the persistent grants feature since it unconditionally checked
if frontend supports the persistent grants feature for every connect
('connect_ring()') and decided whether it should use persistent grans or
not.
However, commit aac8a70db2 ("xen-blkback: add a parameter for
disabling of persistent grants") has mistakenly changed the behavior.
It made the frontend feature support check to not be repeated once it
shown the 'feature_persistent' as 'false', or the frontend doesn't
support persistent grants.
This commit changes the behavior of the parameter to make effect for
every connect, so that the previous workflow can work again as expected.
[1] https://lore.kernel.org/xen-devel/CAJwUmVB6H3iTs-C+U=v-pwJB7-_ZRHPxHzKRJZ22xEPW7z8a=g@mail.gmail.com/
Reported-by: Andrii Chepurnyi <andrii.chepurnyi82@gmail.com>
Fixes: aac8a70db2 ("xen-blkback: add a parameter for disabling of persistent grants")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
Signed-off-by: SeongJae Park <sj@kernel.org>
Reviewed-by: Maximilian Heyne <mheyne@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220715225108.193398-3-sj@kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Persistent grants feature can be used only when both backend and the
frontend supports the feature. The feature was always supported by
'blkback', but commit aac8a70db2 ("xen-blkback: add a parameter for
disabling of persistent grants") has introduced a parameter for
disabling it runtime.
To avoid the parameter be updated while being used by 'blkback', the
commit caches the parameter into 'vbd->feature_gnt_persistent' in
'xen_vbd_create()', and then check if the guest also supports the
feature and finally updates the field in 'connect_ring()'.
However, 'connect_ring()' could be called before 'xen_vbd_create()', so
later execution of 'xen_vbd_create()' can wrongly overwrite 'true' to
'vbd->feature_gnt_persistent'. As a result, 'blkback' could try to use
'persistent grants' feature even if the guest doesn't support the
feature.
This commit fixes the issue by moving the parameter value caching to
'xen_blkif_alloc()', which allocates the 'blkif'. Because the struct
embeds 'vbd' object, which will be used by 'connect_ring()' later, this
should be called before 'connect_ring()' and therefore this should be
the right and safe place to do the caching.
Fixes: aac8a70db2 ("xen-blkback: add a parameter for disabling of persistent grants")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
Signed-off-by: SeongJae Park <sj@kernel.org>
Reviewed-by: Maximilian Heyne <mheyne@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220715225108.193398-2-sj@kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Luis and others, almost exclusively in the filesystem. Several patches
touch files outside of our normal purview to set the stage for bringing
in Jeff's long awaited ceph+fscrypt series in the near future. All of
them have appropriate acks and sat in linux-next for a while.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmL1HF8THGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHziwOuB/97JKHFuOlP1HrD6fYe5a0ul9zC9VG4
57XPDNqG2PSmfXCjvZhyVU4n53sUlJTqzKDSTXydoPCMQjtyHvysA6gEvcgUJFPd
PHaZDCd9TmqX8my67NiTK70RVpNR9BujJMVMbOfM+aaisl0K6WQbitO+BfhEiJcK
QStdKm5lPyf02ESH9jF+Ga0DpokARaLbtDFH7975owxske6gWuoPBCJNrkMooKiX
LjgEmNgH1F/sJSZXftmKdlw9DtGBFaLQBdfbfSB5oVPRb7chI7xBeraNr6Od3rls
o4davbFkcsOr+s6LJPDH2BJobmOg+HoMoma7ezspF7ZqBF4Uipv5j3VC
=1427
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.20-rc1' of https://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"We have a good pile of various fixes and cleanups from Xiubo, Jeff,
Luis and others, almost exclusively in the filesystem.
Several patches touch files outside of our normal purview to set the
stage for bringing in Jeff's long awaited ceph+fscrypt series in the
near future. All of them have appropriate acks and sat in linux-next
for a while"
* tag 'ceph-for-5.20-rc1' of https://github.com/ceph/ceph-client: (27 commits)
libceph: clean up ceph_osdc_start_request prototype
libceph: fix ceph_pagelist_reserve() comment typo
ceph: remove useless check for the folio
ceph: don't truncate file in atomic_open
ceph: make f_bsize always equal to f_frsize
ceph: flush the dirty caps immediatelly when quota is approaching
libceph: print fsid and epoch with osd id
libceph: check pointer before assigned to "c->rules[]"
ceph: don't get the inline data for new creating files
ceph: update the auth cap when the async create req is forwarded
ceph: make change_auth_cap_ses a global symbol
ceph: fix incorrect old_size length in ceph_mds_request_args
ceph: switch back to testing for NULL folio->private in ceph_dirty_folio
ceph: call netfs_subreq_terminated with was_async == false
ceph: convert to generic_file_llseek
ceph: fix the incorrect comment for the ceph_mds_caps struct
ceph: don't leak snap_rwsem in handle_cap_grant
ceph: prevent a client from exceeding the MDS maximum xattr size
ceph: choose auth MDS for getxattr with the Xs caps
ceph: add session already open notify support
...
Lin, Yang Shi, Anshuman Khandual and Mike Rapoport
- Some kmemleak fixes from Patrick Wang and Waiman Long
- DAMON updates from SeongJae Park
- memcg debug/visibility work from Roman Gushchin
- vmalloc speedup from Uladzislau Rezki
- more folio conversion work from Matthew Wilcox
- enhancements for coherent device memory mapping from Alex Sierra
- addition of shared pages tracking and CoW support for fsdax, from
Shiyang Ruan
- hugetlb optimizations from Mike Kravetz
- Mel Gorman has contributed some pagealloc changes to improve latency
and realtime behaviour.
- mprotect soft-dirty checking has been improved by Peter Xu
- Many other singleton patches all over the place
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCYuravgAKCRDdBJ7gKXxA
jpqSAQDrXSdII+ht9kSHlaCVYjqRFQz/rRvURQrWQV74f6aeiAD+NHHeDPwZn11/
SPktqEUrF1pxnGQxqLh1kUFUhsVZQgE=
=w/UH
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2022-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
"Most of the MM queue. A few things are still pending.
Liam's maple tree rework didn't make it. This has resulted in a few
other minor patch series being held over for next time.
Multi-gen LRU still isn't merged as we were waiting for mapletree to
stabilize. The current plan is to merge MGLRU into -mm soon and to
later reintroduce mapletree, with a view to hopefully getting both
into 6.1-rc1.
Summary:
- The usual batches of cleanups from Baoquan He, Muchun Song, Miaohe
Lin, Yang Shi, Anshuman Khandual and Mike Rapoport
- Some kmemleak fixes from Patrick Wang and Waiman Long
- DAMON updates from SeongJae Park
- memcg debug/visibility work from Roman Gushchin
- vmalloc speedup from Uladzislau Rezki
- more folio conversion work from Matthew Wilcox
- enhancements for coherent device memory mapping from Alex Sierra
- addition of shared pages tracking and CoW support for fsdax, from
Shiyang Ruan
- hugetlb optimizations from Mike Kravetz
- Mel Gorman has contributed some pagealloc changes to improve
latency and realtime behaviour.
- mprotect soft-dirty checking has been improved by Peter Xu
- Many other singleton patches all over the place"
[ XFS merge from hell as per Darrick Wong in
https://lore.kernel.org/all/YshKnxb4VwXycPO8@magnolia/ ]
* tag 'mm-stable-2022-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (282 commits)
tools/testing/selftests/vm/hmm-tests.c: fix build
mm: Kconfig: fix typo
mm: memory-failure: convert to pr_fmt()
mm: use is_zone_movable_page() helper
hugetlbfs: fix inaccurate comment in hugetlbfs_statfs()
hugetlbfs: cleanup some comments in inode.c
hugetlbfs: remove unneeded header file
hugetlbfs: remove unneeded hugetlbfs_ops forward declaration
hugetlbfs: use helper macro SZ_1{K,M}
mm: cleanup is_highmem()
mm/hmm: add a test for cross device private faults
selftests: add soft-dirty into run_vmtests.sh
selftests: soft-dirty: add test for mprotect
mm/mprotect: fix soft-dirty check in can_change_pte_writable()
mm: memcontrol: fix potential oom_lock recursion deadlock
mm/gup.c: fix formatting in check_and_migrate_movable_page()
xfs: fail dax mount if reflink is enabled on a partition
mm/memcontrol.c: remove the redundant updating of stats_flush_threshold
userfaultfd: don't fail on unrecognized features
hugetlb_cgroup: fix wrong hugetlb cgroup numa stat
...
This function always returns 0, and ignores the nofail boolean. Drop the
nofail argument, make the function void return and fix up the callers.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
UBLK_IO_NEED_GET_DATA is one ublk IO command. It is designed for a user
application who wants to allocate IO buffer and set IO buffer address
only after it receives an IO request from ublksrv. This is a reasonable
scenario because these users may use a RPC framework as one IO backend
to handle IO requests passed from ublksrv. And a RPC framework may
allocate its own buffer(or memory pool).
This new feature (UBLK_F_NEED_GET_DATA) is optional for ublk users.
Related userspace code has been added in ublksrv[1] as one pull request.
Test cases for this feature are added in ublksrv and all the tests pass.
The performance result shows that this new feature does bring additional
latency because one IO is issued back to ublk_drv once again to copy data
from bio vectors to user-provided data buffer. UBLK_IO_NEED_GET_DATA is
suitable for bigger block size such as 512B or 1MB.
[1] https://github.com/ming1/ubdsrv
Signed-off-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/3a21007ea1be8304246e654cebbd581ab0012623.1659011443.git.ZiyangZhang@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove all block device related info from ublksrv_ctrl_dev_info,
meantime reduce its size into 64 bytes because:
1) ublksrv_ctrl_dev_info becomes cleaner without including any
block related info
2) generic set/get parameter command can be used to set block
related setting easily and cleanly
3) generic set/get parameter command can be used for extending
ublk without needing more info in ublksrv_ctrl_dev_info
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220730092750.1118167-5-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add two commands to set/get parameters generically.
One important goal of ublk is to provide generic framework for making
block device by userspace flexibly.
As one generic block device, there are still lots of block parameters,
such as max_sectors, write_cache/fua, discard related limits,
zoned parameters, ...., so this patch starts to add generic mechanism
for set/get device parameters.
Both generic block parameters(all kinds of queue settings) and ublk
feature parameters can be covered with this way, then it becomes quite
easy to extend in future.
Add two parameter types are used so far: basic(covers basic queue setting
and misc settings which can't be grouped easily) and discard, basic type
must be set, and discard type becomes optional now
This way provides mechanism to simulate any kind of generic block device
from userspace easily, from both block queue setting viewpoint or ublk
feature viewpoint.
The style of putting all parameters together is suggested by Christoph.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220730092750.1118167-4-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
->free_disk is only called after disk is added successfully, so
drop ublk device reference in case of add_disk() failure.
Fixes: 6d9e6dfdf3 ("ublk: defer disk allocation")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220730092750.1118167-3-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Each ublk queue is started before adding disk, we have to cancel queues in
ublk_stop_dev() so that ubq daemon can be exited, otherwise DEL_DEV command
may hang forever.
Also avoid to cancel queues two times by checking if queue is ready,
otherwise use-after-free on io_uring may be triggered because ublk_stop_dev
is called by ublk_remove() too.
Fixes: 71f28f3136 ("ublk_drv: add io_uring based userspace block driver")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220730092750.1118167-2-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The double indirect bio leads to somewhat suboptimal code generation.
Instead return the (original or split) bio, and make sure the
request_queue arguments to the lower level helpers is passed after the
bio to avoid constant reshuffling of the argument passing registers.
Also give it and the helpers used to implement it more descriptive names.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220727162300.3089193-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This driver is for fairly obscure hardware, and has only seen random
drive-by changes after the maintainer stopped working on it in 2005
(about a year and a half after it was introduced). It has some
"interesting" block layer interactions, so let's just drop it unless
anyone complains.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220721064102.1715460-1-hch@lst.de
[axboe: fix date typo, it was in 2005, not 2015]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
commit 1243172d58 ("nbd: use pr_err to output error message") tries
to define pr_fmt and use short pr_err() to output error message,
however, the definition is missed.
This patch also remove existing "nbd:" inside pr_err().
Fixes: 1243172d58 ("nbd: use pr_err to output error message")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20220723082427.3890655-1-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There needs to be some error checking if ida_simple_get() fails.
Also call ida_free() if there are errors later.
Fixes: 94bc02e30f ("nullb: use ida to manage index")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YtEhXsr6vJeoiYhd@kili
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Allow setting via configfs these two options:
no_sched
shared_tag_bitmap
Previously these could only be activated as module parameters.
Still missing are:
shared_tags
timeout
requeue
init_hctx
Signed-off-by: Vincent Fu <vincent.fu@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220708174943.87787-3-vincent.fu@samsung.com
[axboe: fold in nullb == NULL fix]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add as module parameters these options:
memory_backed
discard
mbps
cache_size
Previously these could only be set via configfs.
Still missing is bad_blocks.
The kernel test robot found a documentation formatting issue in v1 of
this patch.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vincent Fu <vincent.fu@samsung.com>
Link: https://lore.kernel.org/r/20220708174943.87787-2-vincent.fu@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The structure rnbd_srv_session maintains a list and an xarray of
rnbd_srv_dev. There is no need to keep both as one of them can serve the
purpose.
Since one of the places where the lookup of rnbd_srv_dev using
rnbd_srv_session is IO path, an xarray would serve us better than a list
traversal. Hence remove sess_dev_list from rnbd_srv_session, and replace
its uses from xarray.
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Reviewed-by: Aleksei Marov <aleksei.marov@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20220707143122.460362-3-haris.iqbal@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
After setting keep_id if the mutex trylock fails, the keep_id stays set
for the rest of the sess_dev lifetime.
Therefore, set keep_id to true after mutex_trylock succeeds, so that a
failure of trylock does'nt touch keep_id.
Fixes: b168e1d85c ("block/rnbd-srv: Prevent a deadlock generated by accessing sysfs in parallel")
Cc: gi-oh.kim@ionos.com
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/20220707143122.460362-2-haris.iqbal@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Let's change the parameter type to 'sector_t' then we don't need to cast
it from rnbd_clt_resize_dev_store, and update rnbd_clt_resize_disk too.
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Link: https://lore.kernel.org/r/20220706133152.12058-8-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, process_msg_open_rsp checks if capacity changed or not before
call rnbd_clt_change_capacity while the checking also make sense for
rnbd_clt_resize_dev_store, let's move the checking into the function.
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Link: https://lore.kernel.org/r/20220706133152.12058-7-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
While at it, let re-arrange the struct to remove holes.
Before, pahole reports
/* size: 232, cachelines: 4, members: 17 */
/* sum members: 224, holes: 2, sum holes: 8 */
/* last cacheline: 40 bytes */
After the change, the report changes to
/* size: 224, cachelines: 4, members: 17 */
/* last cacheline: 32 bytes */
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Link: https://lore.kernel.org/r/20220706133152.12058-6-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Previously, both map and remap trigger rnbd_clt_set_dev_attr to set
some members in rnbd_clt_dev such as wc, fua and logical_block_size
etc, but those members are only useful for map scenario given the
setup_request_queue is only called from the path:
rnbd_clt_map_device -> rnbd_client_setup_device
Since rnbd_clt_map_device frees rsp after rnbd_client_setup_device,
we can pass rsp to rnbd_client_setup_device and it's callees, which
means queue's attributes can be set directly from relevant members
of rsp instead from rnbd_clt_dev.
After that, we can kill 11 members from rnbd_clt_dev, and we don't
need rnbd_clt_set_dev_attr either.
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Link: https://lore.kernel.org/r/20220706133152.12058-5-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The member is not needed since we can call get_disk_ro to achieve the
same goal.
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Link: https://lore.kernel.org/r/20220706133152.12058-4-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For map scenario, rsp is freed in two places:
1. msg_open_conf frees rsp if rtrs_clt_request returns 0.
2. Otherwise, rsp is freed by the call sites of rtrs_clt_request.
Now, We'd like to control full lifecycle of rsp in rnbd_clt_map_device,
with that, it is feasible to pass rsp to rnbd_client_setup_device in
next commit.
For 1, it is possible to free rsp from the caller of send_usr_msg
because of the synchronization of iu->comp.wait. And we put iu later
in rnbd_clt_map_device to ensure order of release rsp and iu.
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Link: https://lore.kernel.org/r/20220706133152.12058-3-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Let's open code it in rnbd_clt_map_device, then we can use information
from rsp to setup gendisk and request_queue in next commits. After that,
we can remove some members (wc, fua and max_hw_sectors etc) from struct
rnbd_clt_dev.
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Link: https://lore.kernel.org/r/20220706133152.12058-2-guoqing.jiang@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We usually do all our bitmap IO in units of PAGE_SIZE.
With very small or oddly sized external meta data, or with
PAGE_SIZE != 4k, it can happen that our last on-disk bitmap page
is not fully PAGE_SIZE aligned, so we may need to adjust the size
of the IO.
We used to do that with
min_t(unsigned int, PAGE_SIZE,
last_allowed_sector - current_offset);
And for just the right diff, (unsigned int)(diff) will result in 0.
A bio of length 0 will correctly be rejected with an IO error
(and some scary WARN_ON_ONCE()) by the scsi layer.
Do the calculation properly.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20220622204932.196830-1-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=celk
-----END PGP SIGNATURE-----
Merge tag 'for-5.20/block-2022-07-29' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Improve the type checking of request flags (Bart)
- Ensure queue mapping for a single queues always picks the right queue
(Bart)
- Sanitize the io priority handling (Jan)
- rq-qos race fix (Jinke)
- Reserved tags handling improvements (John)
- Separate memory alignment from file/disk offset aligment for O_DIRECT
(Keith)
- Add new ublk driver, userspace block driver using io_uring for
communication with the userspace backend (Ming)
- Use try_cmpxchg() to cleanup the code in various spots (Uros)
- Finally remove bdevname() (Christoph)
- Clean up the zoned device handling (Christoph)
- Clean up independent access range support (Christoph)
- Clean up and improve block sysfs handling (Christoph)
- Clean up and improve teardown of block devices.
This turns the usual two step process into something that is simpler
to implement and handle in block drivers (Christoph)
- Clean up chunk size handling (Christoph)
- Misc cleanups and fixes (Bart, Bo, Dan, GuoYong, Jason, Keith, Liu,
Ming, Sebastian, Yang, Ying)
* tag 'for-5.20/block-2022-07-29' of git://git.kernel.dk/linux-block: (178 commits)
ublk_drv: fix double shift bug
ublk_drv: make sure that correct flags(features) returned to userspace
ublk_drv: fix error handling of ublk_add_dev
ublk_drv: fix lockdep warning
block: remove __blk_get_queue
block: call blk_mq_exit_queue from disk_release for never added disks
blk-mq: fix error handling in __blk_mq_alloc_disk
ublk: defer disk allocation
ublk: rewrite ublk_ctrl_get_queue_affinity to not rely on hctx->cpumask
ublk: fold __ublk_create_dev into ublk_ctrl_add_dev
ublk: cleanup ublk_ctrl_uring_cmd
ublk: simplify ublk_ch_open and ublk_ch_release
ublk: remove the empty open and release block device operations
ublk: remove UBLK_IO_F_PREFLUSH
ublk: add a MAINTAINERS entry
block: don't allow the same type rq_qos add more than once
mmc: fix disk/queue leak in case of adding disk failure
ublk_drv: fix an IS_ERR() vs NULL check
ublk: remove UBLK_IO_F_INTEGRITY
ublk_drv: remove unneeded semicolon
...
zs_malloc returns 0 if it fails. zs_zpool_malloc will return -1 when
zs_malloc return 0. But -1 makes the return value unclear.
For example, when zswap_frontswap_store calls zs_malloc through
zs_zpool_malloc, it will return -1 to its caller. The other return value
is -EINVAL, -ENODEV or something else.
This commit changes zs_malloc to return ERR_PTR on failure. It didn't
just let zs_zpool_malloc return -ENOMEM becaue zs_malloc has two types of
failure:
- size is not OK return -EINVAL
- memory alloc fail return -ENOMEM.
Link: https://lkml.kernel.org/r/20220714080757.12161-1-teawater@gmail.com
Signed-off-by: Hui Zhu <teawater@antgroup.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The test/clear_bit() functions take a bit number, but this code is
passing as shifted value. It's the equivalent of saying BIT(BIT(0))
instead of just BIT(0).
This doesn't affect runtime because numbers are small and it's done
consistently.
Fixes: fa36204556 ("ublk: simplify ublk_ch_open and ublk_ch_release")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/Yt/2R/+MJf/MSoyl@kili
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Userspace may support more features or new added flags, but the driver
side can be old, so make sure correct flags(features) returned to
userpsace, then userspace can work as expected.
Also mark the 2nd flags as reversed, just use the 1st one. When we run
out of flags, the reserved one can be handled at that time.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220722103817.631258-3-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
__ublk_destroy_dev() is called for handling error in ublk_add_dev(),
but either tagset isn't allocated or mutex isn't initialized.
So fix the issue by letting replacing ublk_add_dev with a
ublk_add_tag_set function that is much more limited in scope and
instead unwind every single step directly in ublk_ctrl_add_dev.
To allow for this refactor the device freeing so that there is
a helper for freeing the device number instead of coupling that
with freeing the mutex and the memory.
Note that this now copies the dev_info to userspace before adding
the character device. This not only simplifies the erro handling
in ublk_ctrl_add_dev, but also means that the character device
can only be seen by userspace if the device addition succeeded.
Based on a patch from Ming Lei.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220722103817.631258-2-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Defer allocating the gendisk and request_queue until UBLK_CMD_START_DEV
is called. This avoids funky life times where a disk is allocated
and then can be added and removed multiple times, which has never been
supported by the block layer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220721130916.1869719-9-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Looking at the hctxs and cpumap is not safe without at very last a RCU
reference. It also requires the queue to be set up before starting the
device, which leads to rather awkward life time rules.
Instead rewrite ublk_ctrl_get_queue_affinity to just build the cpumask
directly from the mq_map in the tag set, similar to hctx->cpumask is
built.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220721130916.1869719-8-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fold __ublk_create_dev into its only caller to avoid the packing and
unpacking of the return value into an ERR_PTR.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220721130916.1869719-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move all per-command work into the per-command ublk_ctrl_* helpers
instead of being split over those, ublk_ctrl_cmd_validate, and the main
ublk_ctrl_uring_cmd handler. To facilitate that, the old
ublk_ctrl_stop_dev function that just contained two function calls is
folded into both callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220721130916.1869719-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
fops->open and fops->release are always paired. Use simple atomic bit
ops ot indicate if the device is opened instead of a count that can
only be 0 and 1 and a useless cmpxchg loop in ublk_ch_release.
Also don't bother clearing file->private_data is the file is about to
be freed anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220721130916.1869719-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No need to define empty versions, they can just be left out.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220721130916.1869719-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
REQ_PREFLUSH is turned into REQ_OP_FLUSH by the flush state machine
and thus never seen by a blk-mq based driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220721130916.1869719-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The ublk protocol has no mechanism to actually transfer the integrity
metadata, so don't define this flag, which requires that an integrity
payload is attached to a bio.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220718063013.335531-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Eliminate the following coccicheck warnings:
./drivers/block/ublk_drv.c:1467:2-3: Unneeded semicolon
./drivers/block/ublk_drv.c:1528:2-3: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220718015431.40185-1-yang.lee@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If blk_mq_init_queue() fails, it should return error code in ublk_add_dev()
Fixes: cebbe577cb ("ublk_drv: fix request queue leak")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220718042408.3132835-1-yangyingliang@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
drivers/block/zram/zram_drv.c:55:45: warning: 'zram_wb_devops' defined but not used [-Wunused-const-variable=]
Fix the above warning if CONFIG_ZRAM_WRITEBACK not enabled.
Link: https://lkml.kernel.org/r/20220608072534.68850-1-wangkefeng.wang@huawei.com
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
After applying -Wmaybe-uninitialized manually, two build warnings are
triggered:
drivers/block/ublk_drv.c:940:11: warning: ‘io’ may be used uninitialized [-Wmaybe-uninitialized]
940 | io->flags &= ~UBLK_IO_FLAG_ACTIVE;
drivers/block/ublk_drv.c: In function ‘ublk_ctrl_uring_cmd’:
drivers/block/ublk_drv.c:1531:9: warning: ‘ret’ may be used uninitialized [-Wmaybe-uninitialized]
Fix the 1st one by removing 'io->flags &= ~UBLK_IO_FLAG_ACTIVE;' which
isn't needed since the function always return successfully after setting
this flag.
Fix the 2nd one by always initializing 'ret'.
Also fix another sparse warning of 'sparse: sparse: incorrect type in return
expression' by changing return type of ublk_setup_iod().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220716095344.222674-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Improve static type checking by using the enum req_op type where
appropriate.
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-19-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Improve static type checking by using the enum req_op type for request
operations and the new blk_opf_t type for request flags.
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-18-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Improve static type checking by using the new blk_opf_t type to represent
the combination of a request and request flags.
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Cc: Md. Haris Iqbal <haris.iqbal@ionos.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-17-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since the type of request.cmd_flags has been changed from u32 into
blk_opf_t, use the __force keyword when casting to an integer type to
prevent that sparse warns about this cast.
Cc: Denis Efremov <efremov@linux.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-16-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Combine the drbd_submit_peer_request() 'op' and 'op_flags' arguments
into a single argument. This patch does not change any functionality.
Reviewed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-15-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Improve static type checking by using the enum req_op type for variables
that represent a request operation and the new blk_opf_t type for
variables that represent request flags.
Reviewed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-14-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Improve static type checking by using the enum req_op type for a
function argument that represents a request operation.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-13-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Improve static type checking by changing the type of the value returned by
req_op() and bio_op() from unsigned int into enum req_op. Insert
'default: break;' in switch statements on the enum req_op type to prevent
that the compiler warns about these switch statements.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@kernel.org>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-5-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All .rw_page() callers pass an enum req_op value as last argument. Make
this explicit by changing the type of the last argument into enum req_op.
See also commit 3f289dcb4b ("block: make bdev_ops->rw_page() take a
REQ_OP instead of bool").
Cc: Tejun Heo <tj@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-4-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The type name enum req_opf is misleading since it suggests that values of
this type include both an operation type and flags. Since values of this
type represent an operation only, change the type name into enum req_op.
Convert the enum req_op documentation into kernel-doc format. Move a few
definitions such that the enum req_op documentation occurs just above
the enum req_op definition.
The name "req_opf" was introduced by commit ef295ecf09 ("block: better op
and flags encoding").
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-2-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just print the block device name directly using the %pg format specifier.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220713055317.1888500-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just use the %pg format specifier instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220713055317.1888500-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just use the %pg format specifier instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220713055317.1888500-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just use the %pg format specifier instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220713055317.1888500-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Call blk_cleanup_queue() in release code path for fixing request
queue leak.
Also for-5.20/block has cleaned up blk_cleanup_queue(), which is
basically merged to del_gendisk() if blk_mq_alloc_disk() is used
for allocating disk and queue.
However, ublk may not add disk in case of starting device failure, then
del_gendisk() won't be called when removing ublk device, so blk_mq_exit_queue
will not be callsed, and it can be bit hard to deal with this kind of
merge conflict.
Turns out ublk's queue/disk use model is very similar with scsi, so switch
to scsi's model by allocating disk and queue independently, then it can be
quite easy to handle v5.20 merge conflict by replacing blk_cleanup_queue
with blk_mq_destroy_queue.
Reported-by: Jens Axboe <axboe@kernel.dk>
Fixes: 71f28f3136 ("ublk_drv: add io_uring based userspace block driver")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220714103201.131648-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use task_work_add if it is available, since task_work_add can bring
up better performance, especially batching signaling ->ubq_daemon can
be done.
It is observed that task_work_add() can boost iops by +4% on random
4k io test. Also except for completing io command, all other code
paths are same with completing io command via
io_uring_cmd_complete_in_task.
Meantime add one flag of UBLK_F_URING_CMD_COMP_IN_TASK for comparing
the mode easily.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220713140711.97356-3-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is the driver part of userspace block driver(ublk driver), the other
part is userspace daemon part(ublksrv)[1].
The two parts communicate by io_uring's IORING_OP_URING_CMD with one
shared cmd buffer for storing io command, and the buffer is read only for
ublksrv, each io command is indexed by io request tag directly, and is
written by ublk driver.
For example, when one READ io request is submitted to ublk block driver,
ublk driver stores the io command into cmd buffer first, then completes
one IORING_OP_URING_CMD for notifying ublksrv, and the URING_CMD is issued
to ublk driver beforehand by ublksrv for getting notification of any new
io request, and each URING_CMD is associated with one io request by tag.
After ublksrv gets the io command, it translates and handles the ublk io
request, such as, for the ublk-loop target, ublksrv translates the request
into same request on another file or disk, like the kernel loop block
driver. In ublksrv's implementation, the io is still handled by io_uring,
and share same ring with IORING_OP_URING_CMD command. When the target io
request is done, the same IORING_OP_URING_CMD is issued to ublk driver for
both committing io request result and getting future notification of new
io request.
Another thing done by ublk driver is to copy data between kernel io
request and ublksrv's io buffer:
1) before ubsrv handles WRITE request, copy the request's data into
ublksrv's userspace io buffer, so that ublksrv can handle the write
request
2) after ubsrv handles READ request, copy ublksrv's userspace io buffer
into this READ request, then ublk driver can complete the READ request
Zero copy may be switched if mm is ready to support it.
ublk driver doesn't handle any logic of the specific user space driver,
so it is small/simple enough.
[1] ublksrv
https://github.com/ming1/ubdsrv
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220713140711.97356-2-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the zone related fields that are currently stored in
struct request_queue to struct gendisk as these are part of the highlevel
block layer API and are only used for non-passthrough I/O that requires
the gendisk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-17-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pass a block_device instead of a request_queue as that is what most
callers have at hand.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-12-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Switch to a gendisk based API in preparation for moving all zone related
fields from the request_queue to the gendisk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-11-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
