Move the reset operation to the common part to reduce the code
redundancy. They are actually the same and needed for all SoCs.
Disabling power and clock are unnecessary for MT7620 and will be
removed. In vendor SDK, it's used to save the power when the PCI
driver is not selected. The MT7628 GPIO pinctrl has been removed
because this should be done in device-tree. Some delay intervals
have also been increased to follow the recommendations of the SoC
SDK and datasheet. Tested on both MT7620 and MT7628.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
These missing register init values are ported from the vendor SDK.
It should have some stability enhancements. Tested on both MT7620
and MT7628.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Host bridge registers and PCI RC control registers have different
memory base. pcie_m32() is used to write the RC control registers
instead of bridge registers. This patch introduces bridge_m32()
and use it to operate bridge registers to fix the access issue.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
When a bridge window contains big and small resource(s), the small
resource(s) may not amount to the half of the size of the big resource
which would allow calculate_head_align() to shrink the head alignment.
This results in always placing the small resource(s) after the big
resource.
In general, it would be good to be able to place the small resource(s)
before the big resource to achieve better utilization of the address space.
In the cases where the large resource can only fit at the end of the
window, it is even required.
However, carrying the information over from pbus_size_mem() and
calculate_head_align() to __pci_assign_resource() and
pcibios_align_resource() is not easy with the current data structures.
A somewhat hacky way to move the non-aligning tail part to the head is
possible within pcibios_align_resource(). The free space between the start
of the free space span and the aligned start address can be compared with
the non-aligning remainder of the size. If the free space is larger than
the remainder, placing the remainder before the start address is possible.
This relocation should generally work, because PCI resources consist only
power-of-2 atoms.
Various arch requirements may still need to override the relocation, so the
relocation is only applied selectively in such cases.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221205
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xifer <xiferdev@gmail.com>
Link: https://patch.msgid.link/20260324165633.4583-10-ilpo.jarvinen@linux.intel.com
Aligning res->start by align inside pcibios_align_resource() is unnecessary
because caller of pcibios_align_resource() is __find_resource_space() that
aligns res->start with align before calling pcibios_align_resource().
Aligning by align in case of IORESOURCE_IO && start & 0x300 cannot ever
result in changing start either because 0x300 bits would have not survived
the earlier alignment if align was large enough to have an impact.
Thus, remove the duplicated aligning from pcibios_align_resource().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260324165633.4583-7-ilpo.jarvinen@linux.intel.com
__find_resource_space() calculates the full extent of empty space but only
passes the aligned space to resource_alignf callback. In some situations,
the callback may choose take advantage of the free space before the
requested alignment.
Pass the full extent of the calculated empty space to resource_alignf
callback as an additional parameter.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xifer <xiferdev@gmail.com>
Link: https://patch.msgid.link/20260324165633.4583-3-ilpo.jarvinen@linux.intel.com
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
This is the first half of the driver changes:
- A treewide interface change to the "syscore" operations for
power management, as a preparation for future Tegra specific
changes.
- Reset controller updates with added drivers for LAN969x, eic770
and RZ/G3S SoCs.
- Protection of system controller registers on Renesas and Google SoCs,
to prevent trivially triggering a system crash from e.g. debugfs
access.
- soc_device identification updates on Nvidia, Exynos and Mediatek
- debugfs support in the ST STM32 firewall driver
- Minor updates for SoC drivers on AMD/Xilinx, Renesas, Allwinner, TI
- Cleanups for memory controller support on Nvidia and Renesas
-----BEGIN PGP SIGNATURE-----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=HvlN
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"This is the first half of the driver changes:
- A treewide interface change to the "syscore" operations for power
management, as a preparation for future Tegra specific changes
- Reset controller updates with added drivers for LAN969x, eic770 and
RZ/G3S SoCs
- Protection of system controller registers on Renesas and Google
SoCs, to prevent trivially triggering a system crash from e.g.
debugfs access
- soc_device identification updates on Nvidia, Exynos and Mediatek
- debugfs support in the ST STM32 firewall driver
- Minor updates for SoC drivers on AMD/Xilinx, Renesas, Allwinner, TI
- Cleanups for memory controller support on Nvidia and Renesas"
* tag 'soc-drivers-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (114 commits)
memory: tegra186-emc: Fix missing put_bpmp
Documentation: reset: Remove reset_controller_add_lookup()
reset: fix BIT macro reference
reset: rzg2l-usbphy-ctrl: Fix a NULL vs IS_ERR() bug in probe
reset: th1520: Support reset controllers in more subsystems
reset: th1520: Prepare for supporting multiple controllers
dt-bindings: reset: thead,th1520-reset: Add controllers for more subsys
dt-bindings: reset: thead,th1520-reset: Remove non-VO-subsystem resets
reset: remove legacy reset lookup code
clk: davinci: psc: drop unused reset lookup
reset: rzg2l-usbphy-ctrl: Add support for RZ/G3S SoC
reset: rzg2l-usbphy-ctrl: Add support for USB PWRRDY
dt-bindings: reset: renesas,rzg2l-usbphy-ctrl: Document RZ/G3S support
reset: eswin: Add eic7700 reset driver
dt-bindings: reset: eswin: Documentation for eic7700 SoC
reset: sparx5: add LAN969x support
dt-bindings: reset: microchip: Add LAN969x support
soc: rockchip: grf: Add select correct PWM implementation on RK3368
soc/tegra: pmc: Add USB wake events for Tegra234
amba: tegra-ahb: Fix device leak on SMMU enable
...
Several drivers can benefit from registering per-instance data along
with the syscore operations. To achieve this, move the modifiable fields
out of the syscore_ops structure and into a separate struct syscore that
can be registered with the framework. Add a void * driver data field for
drivers to store contextual data that will be passed to the syscore ops.
Acked-by: Rafael J. Wysocki (Intel) <rafael@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to Maciej W. Rozycki <macro@orcam.me.uk>, the
mips_pcibios_init() for malta adjusts root bus IO resource start
address to prevent interfering with PIIX4 I/O cycle decoding. Adjusting
lower bound leaves PIIX4 IO resources outside of the root bus resource
and assign_fixed_resource_on_bus() does not link the resources into the
resource tree.
Prior to commit ae81aad5c2 ("MIPS: PCI: Use pci_enable_resources()") the
arch specific pcibios_enable_resources() did not check if the resources
were assigned which diverges from what PCI core checks, effectively hiding
the PIIX4 IO resources were not properly within the resource tree. After
starting to use pcibios_enable_resources() from PCI core, enabling PIIX4
fails:
ata_piix 0000:00:0a.1: BAR 0 [io 0x01f0-0x01f7]: not claimed; can't enable device
ata_piix 0000:00:0a.1: probe with driver ata_piix failed with error -22
MIPS PCI code already has support for enforcing lower bounds using
PCIBIOS_MIN_IO in pcibios_align_resource() without altering the IO window
start address itself. Make malta PCI code too to use PCIBIOS_MIN_IO.
Fixes: ae81aad5c2 ("MIPS: PCI: Use pci_enable_resources()")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/linux-pci/9085ab12-1559-4462-9b18-f03dcb9a4088@roeck-us.net/
Suggested-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/linux-pci/alpine.DEB.2.21.2510132229120.39634@angie.orcam.me.uk/
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Maciej W. Rozycki <macro@orcam.me.uk>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://patch.msgid.link/20251017110903.1973-1-ilpo.jarvinen@linux.intel.com
pci-legacy.c under MIPS has a copy of pci_enable_resources() named as
pcibios_enable_resources(). Having own copy of same functionality could
lead to inconsistencies in behavior, especially now as
pci_enable_resources() and the bridge window resource flags behavior are
going to be altered by upcoming changes.
The check for !r->start && r->end is already covered by the more generic
checks done in pci_enable_resources().
Call pci_enable_resources() from MIPS's pcibios_enable_device() and remove
pcibios_enable_resources().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://patch.msgid.link/20250829131113.36754-4-ilpo.jarvinen@linux.intel.com
Fix the following missing-prototypes build warning:
arch/mips/pci/pci-lantiq.c:239:12: error: no previous prototype for 'pcibios_init' [-Werror=missing-prototypes]
239 | int __init pcibios_init(void)
| ^~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This function is only used in the current source file. Mark it as
static to fix the compilation error:
arch/mips/pci/pci-rt2880.c:267:12: error: no previous prototype for 'pcibios_init' [-Werror=missing-prototypes]
267 | int __init pcibios_init(void)
| ^~~~~~~~~~~~
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
irq_domain_add_*() interfaces are going away as being obsolete now.
Switch to the preferred irq_domain_create_*() ones. Those differ in the
node parameter: They take more generic struct fwnode_handle instead of
struct device_node. Therefore, of_fwnode_handle() is added around the
original parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-26-jirislaby@kernel.org
Naming interrupt domains host is confusing at best and the irqdomain code
uses both domain and host inconsistently.
Therefore rename irq_get_default_host() to irq_get_default_domain().
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-4-jirislaby@kernel.org
-----BEGIN PGP SIGNATURE-----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=IdU/
-----END PGP SIGNATURE-----
Merge tag 'mips_6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
"Cleanups and fixes"
* tag 'mips_6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: pci-legacy: Override pci_address_to_pio
MIPS: Loongson64: env: Use str_on_off() helper in prom_lefi_init_env()
MIPS: migrate to generic rule for built-in DTBs
mips: fix shmctl/semctl/msgctl syscall for o32
mips/math-emu: fix emulation of the prefx instruction
MIPS: Loongson: Add comments for interface_info
MIPS: Loongson64: remove ROM Size unit in boardinfo
MIPS: traps: Use str_enabled_disabled() in parity_protection_init()
MIPS: ftrace: Declare ftrace_get_parent_ra_addr() as static
Revert "MIPS: csrc-r4k: Select HAVE_UNSTABLE_SCHED_CLOCK if SMP && 64BIT"
MIPS: Fix the wrong format specifier
MIPS: Add a blank line after __HEAD
MIPS: kernel: Rename read/write_c0_ecc to read/writec0_errctl
pci-legacy systems are not using logic_pio to managed PIO
allocations, thus the generic pci_address_to_pio won't work
when PCI_IOBASE is defined.
Override the function to use architecture implementation to
fix the problem.
Cc: stable@vger.kernel.org
Fixes: 4bfb53e7d3 ("mips: add <asm-generic/io.h> including")
Reported-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Closes: https://lore.kernel.org/r/99f75c66-4c2d-45dc-a808-b5ba440c7551@app.fastmail.com/
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This does not matter the least, but there is no other .[ch] file in the
repo that is executable, so clean this up.
Fixes: 29b83a64df ("MIPS: Octeon: Add PCIe link status check")
Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This reverts commit 277a036312.
While fixing old boards with broken DTs, this change will break
newer ones with correct gpio polarity annotation.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Commit 90c2d2eb7a ("MIPS: pci: lantiq: switch to using gpiod API") not
only switched to the gpiod API, but also inverted / changed the polarity
of the GPIO.
According to the PCI specification, the RST# pin is an active-low
signal. However, most of the device trees that have been widely used for
a long time (mainly in the openWrt project) define this GPIO as
active-high and the old driver code inverted the signal internally.
Apparently there are actually boards where the reset gpio must be
operated inverted. For this reason, we cannot use the GPIOD_OUT_LOW/HIGH
flag for initialization. Instead, we must explicitly set the gpio to
value 1 in order to take into account any "GPIO_ACTIVE_LOW" flag that
may have been set.
In order to remain compatible with all these existing device trees, we
should therefore keep the logic as it was before the commit.
Fixes: 90c2d2eb7a ("MIPS: pci: lantiq: switch to using gpiod API")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
read_config_dword() contains strange condition checking ret for a
number of values. The ret variable, however, is always zero because
config_access() never returns anything else. Thus, the retry is always
taken until number of tries is exceeded.
The code looks like it wants to check *val instead of ret to see if the
read gave an error response.
Fixes: 73b4390fb2 ("[MIPS] Routerboard 532: Support for base system")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The standard PCIe configuration read-write interface is used to
access the configuration space of the peripheral PCIe devices
of the mips processor after the PCIe link surprise down, it can
generate kernel panic caused by "Data bus error". So it is
necessary to add PCIe link status check for system protection.
When the PCIe link is down or in training, assigning a value
of 0 to the configuration address can prevent read-write behavior
to the configuration space of peripheral PCIe devices, thereby
preventing kernel panic.
Signed-off-by: Songyang Li <leesongyang@outlook.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Instead of literal, PCI error value should be set with
PCI_SET_ERROR_RESPONSE(). Use it in tx4927_pci_config_read().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmal.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
pci_ops .read/.write must return PCIBIOS_* codes but
tx4927_pci_config_read/write() return -1 when mkaddr() cannot find
devfn from the root bus. Return PCIBIOS_DEVICE_NOT_FOUND instead and
pass that onward in the call chain instead of overwriting the return
value.
Also converts 0 -> PCIBIOS_SUCCESSFUL which has only cosmetic impact.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmal.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
pcibios_plat_dev_init() is called from pcibios_enable_device() that
should return normal errnos, not PCIBIOS return codes. In this case the
impact is only cosmetic because PCIBIOS_SUCCESSFUL equals 0 that is
success code with errnos as well. Nonetheless, remove the inconsistency
by replacing the PCIBIOS_SUCCESSFUL with 0.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmal.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Ever since introduction in the commit e47d488935 ("MIPS: Lantiq: Add
PCI controller support.") ltqpci_plat_dev_init has been unused. In
57c8cb8f24 ("MIPS: pci: convert lantiq driver to OF") also
ltq_pci_plat_arch_init was introduced.
With those commit being more than 10 years ago, it seem neither is
going to get used anytime soon. Thus, remove both unused function
pointer variables.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmal.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fix typos, most reported by "codespell arch/mips". Only touches comments,
no code changes.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-mips@vger.kernel.org
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
With the adding, some default ioremap_xx methods defined in
asm-generic/io.h can be used. E.g the default ioremap_uc() returning
NULL.
We also massaged various headers to avoid nested includes.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
[jiaxun.yang@flygoat.com: Massage more headers, fix ioport defines]
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arch/mips/pci/fixup-lantiq.c requires nothing from <linux/of_irq.h>, so
remove the include of it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
After bbd8810d39 ("PCI: Remove unused includes and superfluous struct
declaration"), <linux/of_pci.h> no longer includes <linux/pci.h>, which
provides the extern declarations for pcibios_plat_dev_init() and
pcibios_map_irq() via <asm/pci.h>.
This results in these new warnings:
arch/mips/pci/fixup-lantiq.c:13:5: warning: no previous prototype for 'pcibios_plat_dev_init' [-Wmissing-prototypes]
arch/mips/pci/fixup-lantiq.c:24:5: warning: no previous prototype for 'pcibios_map_irq' [-Wmissing-prototypes]
Include <linux/pci.h> directly to get these declarations.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310070445.tzRBNYRC-lkp@intel.com/
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
SWIOTLB implementation details should not be exposed to the rest of the
kernel. This will allow to make changes to the implementation without
modifying non-swiotlb code.
To avoid breaking existing users, provide helper functions for the few
required fields.
As a bonus, using a helper function to initialize struct device allows to
get rid of an #ifdef in driver core.
Signed-off-by: Petr Tesarik <petr.tesarik.ext@huawei.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it was merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Usually, We only need to print the error log when there is a PCIe card but
initialization fails. Whether the driver finds the PCIe card or not is the
expected behavior. So it's better to log these information with dev_info().
Tested on MT7628AN router Motorola MWR03.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
These codes are used to read NFTS_TIMEOUT_DELAY register value and
write it into kernel log after writing the register. they are only
used for debugging during driver development, so there is no need
to keep them now.
Tested on MT7628AN router Motorola MWR03.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
While destroying alignment of the assignments in bridge_driver, do it
consistently and use a single space before =.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
- added support for virt board aligned to QEMU MIPS virt board
- added support for doing DMA coherence on a per device base
- reworked handling of RALINK SoCs
- cleanup for Loongon64 barriers
- removed deprecated support for MIPS_CMP SMP handling method
- removed support Sibyte CARMEL and CHRINE boards
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=eo9R
-----END PGP SIGNATURE-----
Merge tag 'mips_6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- added support for Huawei B593u-12
- added support for virt board aligned to QEMU MIPS virt board
- added support for doing DMA coherence on a per device base
- reworked handling of RALINK SoCs
- cleanup for Loongon64 barriers
- removed deprecated support for MIPS_CMP SMP handling method
- removed support Sibyte CARMEL and CHRINE boards
- cleanups and fixes
* tag 'mips_6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (59 commits)
MIPS: uprobes: Restore thread.trap_nr
MIPS: Don't clear _PAGE_SPECIAL in _PAGE_CHG_MASK
MIPS: Sink body of check_bugs_early() into its only call site
MIPS: Mark check_bugs() as __init
Revert "MIPS: generic: Enable all CPUs supported by virt board in Kconfig"
MIPS: octeon_switch: Remove duplicated labels
MIPS: loongson2ef: Add missing break in cs5536_isa
MIPS: Remove set_swbp() in uprobes.c
MIPS: Use def_bool y for ARCH_SUPPORTS_UPROBES
MIPS: fw: Allow firmware to pass a empty env
MIPS: Remove deprecated CONFIG_MIPS_CMP
MIPS: lantiq: remove unused function declaration
MIPS: Drop unused positional parameter in local_irq_{dis,en}able
MIPS: mm: Remove local_cache_flush_page
MIPS: Remove no longer used ide.h
MIPS: mm: Remove unused *cache_page_indexed flush functions
MIPS: generic: Enable all CPUs supported by virt board in Kconfig
MIPS: Add board config for virt board
MIPS: Octeon: Disable CVMSEG by default on other platforms
MIPS: Loongson: Don't select platform features with CPU
...
Instead of open-coding it everywhere introduce a tiny helper that can be
used to iterate over each resource of a PCI device, and convert the most
obvious users into it.
While at it drop doubled empty line before pdev_sort_resources().
No functional changes intended.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230330162434.35055-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: zhang songyi <zhang.songyi@zte.com.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This patch switches the driver from legacy gpio API to the newer
gpiod API.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Don't use "/**" kernel-doc notation for comments that are not in
kernel-doc format.
Eliminates one warning:
arch/mips/pci/pci-ar2315.c:6: warning: This comment starts with
'/**', but isn't a kernel-doc comment. Refer
Documentation/doc-guide/kernel-doc.rst
* Both AR2315 and AR2316 chips have PCI interface unit, which supports DMA
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Aditya Srivastava <yashsri421@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Rearrange kernel-doc notation for 2 functions to eliminate
kernel-doc warnings. Use Return: notation for the function
return value description. Add function short descriptions
for both functions.
Correct 2 typos.
Fixes these kernel-doc warnings:
msi-octeon.c:49: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Called when a driver request MSI interrupts instead of the
msi-octeon.c:49: warning: missing initial short description on line:
* Called when a driver request MSI interrupts instead of the
msi-octeon.c:62: warning: No description found for return value of 'arch_setup_msi_irq'
msi-octeon.c:189: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Called when a device no longer needs its MSI interrupts. All
msi-octeon.c:189: warning: missing initial short description on line:
* Called when a device no longer needs its MSI interrupts. All
Fixes: e8635b484f ("MIPS: Add Cavium OCTEON PCI support.")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Aditya Srivastava <yashsri421@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
