Add support for the Geist board based on the Renesas R-Car R8A779MD (M3Le)
SoC, a register-compatible variant of the R8A77965 (M3-N) with reduced set
of peripherals.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Nguyen Tran <nguyen.tran.pz@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20260522172000.15096-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the initial device tree for the Renesas RZ/G3L SMARC EVK board.
Added placeholders to avoid compilation error with the common code in
renesas-smarc2.dtsi.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://patch.msgid.link/20260324114329.268249-12-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add device tree overlay to support the MayQueen PixPaper e-paper display
on the Renesas RZ/V2H EVK (KAKIP board). The display is connected via
SPI0 interface and uses GPIO pins for reset, busy, and DC control.
The overlay configures:
- RSPI0 pinmux for SPI communication (MOSI, MISO, CLK, CE0),
- PixPaper display device with proper GPIO assignments,
- SPI frequency set to 1MHz for stable operation.
This enables support for the Open-EP Community pixpaper-213-c module on
the RZ/V2H platform.
Signed-off-by: Wig Cheng <onlywig@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260124163611.3279104-1-onlywig@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a DT overlay to bind the Argon40 fan HAT on the Retronix R-Car V4H
Sparrow Hawk board. Fan RPM control and full RPM on reboot has been
tested.
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250907161130.218470-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a DT overlay to bind the Raspberry Pi Display 2 (both 5" and 7"
variants), on the Retronix R-Car V4H Sparrow Hawk board. All of display
output, touch controller, and backlight control have been tested.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250904202838.172579-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add an overlay to connect an IMX462 camera sensor to the J2 connector.
The IMX462 utilizes 4 CSI-2 D-PHY lanes. This enables the video capture
pipeline behind the CSI41 Rx to be enabled to process images from the
sensor.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250905084050.310651-5-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add an overlay to connect an IMX462 camera sensor to the J1 connector.
The IMX462 utilizes 4 CSI-2 D-PHY lanes. This enables the video capture
pipeline behind the CSI40 Rx to be enabled to process images from the
sensor.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250905084050.310651-4-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add an overlay to connect an IMX219 camera sensor to the J2 connector.
The IMX219 utilizes 2 CSI-2 D-PHY lanes. This enables the video capture
pipeline behind the CSI41 Rx to be enabled to process images from the
sensor.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250905084050.310651-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add an overlay to connect an IMX219 camera sensor to the J1 connector.
The IMX219 utilizes 2 CSI-2 D-PHY lanes. This enables the video capture
pipeline behind the CSI40 Rx to be enabled to process images from the
sensor.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250905084050.310651-2-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Introduce device tree overlays for supporting the eMMC (RTK0EF0186B02000BJ)
and microSD (RTK0EF0186B01000BJ) sub-boards connected via the CN15
connector on the RZ/V2H and RZ/V2N evaluation kits.
These overlays enable SDHI0 with appropriate pin control settings, power
regulators, and GPIO handling. Both sub-boards are supported using shared
overlay files that can be applied to either EVK due to their identical
connector layout and interface support.
To support this, new DT overlay files are added:
- `rzv2-evk-cn15-emmc.dtso` for eMMC
- `rzv2-evk-cn15-sd.dtso` for microSD
Additionally, the base DTS files for both EVKs are updated to include a
fixed 1.8V regulator (`reg_1p8v`) needed by the eMMC sub-board and
potential future use cases such as HDMI output.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250627193742.110818-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable CRU, I2C0 and CSI on RZ/G3E SMARC EVK and tie the CSI to the
OV5645 sensor using Device Tree overlay. RZ/G3E SMARK EVK is a RZ/G2L
alike EVK hence reuse rz-smarc-cru-csi-ov5645.dtsi.
Signed-off-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250514162422.910114-5-tommaso.merciai.xr@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
make dtbs:
arch/arm64/boot/dts/renesas/r8a779g0.dtsi:1269.24-1283.5: Warning (spi_bus_bridge): /soc/spi@e6ea0000: incorrect #address-cells for SPI bus
also defined at arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts:471.9-486.3
arch/arm64/boot/dts/renesas/r8a779g0.dtsi:1269.24-1283.5: Warning (spi_bus_bridge): /soc/spi@e6ea0000: incorrect #size-cells for SPI bus
also defined at arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dts:471.9-486.3
arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk.dtb: Warning (spi_bus_reg): Failed prerequisite 'spi_bus_bridge'
The Sparrow Hawk uses the MSIOF module in I2S mode instead of SPI mode,
triggering a conflict between the SPI bus bindings and dtc:
- Serial engines that can be SPI controllers must use "spi" as their
node names,
- Dtc assumes nodes named "spi" are always SPI controllers.
Fix this by disabling this specific warning for this board.
Fixes: ca764d5321 ("arm64: dts: renesas: sparrow-hawk: Add MSIOF Sound support")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/20250506192033.77338015@canb.auug.org.au
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/fbad3581f297d5b95a3b2813bbae7dba25a523fd.1747039399.git.geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the initial device tree for the Renesas RZ/V2N EVK board, based on
the R9A09G056N48 SoC. Enable basic board functionality, including:
- Memory mapping (reserve the first 128MB for the secure area)
- Clock inputs (QEXTAL, RTXIN, AUDIO_EXTAL)
- PINCTRL configurations for peripherals
- Serial console (SCIF)
- SDHI1 with power control and UHS modes
Update the Makefile to include the new DTB.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250407191628.323613-13-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a DT overlay for SCIF1 (of the Renesas RZ/G3S SoC) routed through
the PMOD1_3A interface available on the Renesas RZ SMARC Carrier II
board.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250120130936.1080069-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
White Hawk Single boards can use the same ARD-AUDIO-DA7212 external
audio board as the White Hawk board stack. Add support for building
DTBs for them, and document the small differences in connector labels.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/7c840b6e08e0af8a6b9bd5516969eb585f16e10a.1733402907.git.geert+renesas@glider.be
The White Hawk Single board with R-Car V4H ES3.0 (R8A779G3) uses an
updated version of the R-Car V4H (R8A779G0) SoC.
For now, there are no visible differences compared to the variant
equipped with an R-Car V4H ES2.0 (R8A779G2) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/66d0fe78c393e6df2775287c730464e91732ec56.1733156661.git.geert+renesas@glider.be
Enable the Display Unit and link with the HDMI add-on board connected
to the parallel connector on the RZ/G2UL SMARC EVK by using a Device
Tree overlay.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240826101648.176647-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Eagle board supports an optional "Function expansion board".
The expansion board adds support for HDMI OUT, HDMI capture from two
different sources, and eMMC.
This change only adds support for the two HDMI capture sources.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240224191902.2065733-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable CRU and CSI on RZ/G2UL SMARC EVK and tie the CSI to the OV5645
sensor using a Device Tree overlay.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240213141300.159847-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add initial support for the Renesas Gray Hawk Single board, which is
based on the R-Car V4M (R8A779H0) SoC:
- Memory,
- Crystal oscillators,
- Serial console.
Based on the White Hawk Single DTS, and on a patch for the Gray Hawk
board stack in the BSP by Hai Pham.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/b657402113267acd57aece0b4c681b707e704455.1706194617.git.geert+renesas@glider.be
The White Hawk Single board is a single-board integration of the Renesas
White Hawk CPU and Breakout board stack, based on the R-Car V4H ES2.0
(R8A779G2) SoC.
For now, the only visible differences compared to the board stack are:
- The SoC is an updated version of R-Car V4H (R8A779G0),
- The serial console uses an FT2232H instead of a CP2102 USB-UART
bridge, with CTS/RTS wired.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/2b8d37949c17cca170c1d9e97f10a100b20c5cd9.1706192990.git.geert+renesas@glider.be
Add initial support for the R-Car S4 Starter Kit with R8A779F4
SoC support. Based on a patch in the BSP.
Signed-off-by: Michael Dege <michael.dege@renesas.com>
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Co-developed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87pm1wfn8z.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable CRU, CSI on RZ/G2LC SMARC EVK and tie the CSI to the OV5645 sensor
using Device Tree overlay.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230413114016.16068-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable CRU, CSI on RZ/V2L SMARC EVK and tie the CSI to the OV5645 sensor
using Device Tree overlay. RZ/G2L SMARC EVK and RZ/V2L SMARC EVK have the
same connections for connecting the CSI to OV5645 sensor so just reuse
the existing r9a07g044l2-smarc-cru-csi-ov5645.dtso and create a symbolic
link to this file for RZ/V2L SMARC EVK.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230412185608.64628-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable CRU, CSI on RZ/G2L SMARC EVK and tie the CSI to OV5645 sensor
using Device Tree overlay. rz-smarc-cru-csi-ov5645.dtsi is created so
that RZ/G2L alike EVKs can make use of it.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230322125648.24948-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable sci0 node using dt overlay and disable can{0,1}-stb-hog
nodes in DT overlay as its pins are shared with sci0 pins.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230321114753.75038-6-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
and disable booting for this SoC. Public users only have ES2 onwards.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230307105645.5285-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add R-Car Sound support for the White Hawk board with the
ARD-AUDIO-DA7212 external audio board, using a DT overlay.
Signed-off-by: Linh Phung <linh.phung.jy@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87o7p5l9t7.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Draak and Ebisu boards support an optional LVDS panel. One
compatible panel is the Mitsubishi AA104XD12. Add a corresponding DT
overlay.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20211229193135.28767-4-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Salvator-X and Salvator-XS boards support an optional LVDS panel.
One compatible panel is the Mitsubishi AA104XD12. Add a corresponding DT
overlay.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20211229193135.28767-3-laurent.pinchart+renesas@ideasonboard.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Initial support for the Renesas White Hawk CPU and BreakOut boards.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220428135058.597586-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add basic support for RZ/G2UL SMARC EVK (based on R9A07G043U11):
- memory
- External input clock
- CPG
- DMA
- SCIF
It shares the same carrier board with RZ/G2L, but the pin mapping is
different. Disable the device nodes which are not tested and delete the
corresponding pinctrl definitions.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220412161314.13800-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
