Rename node name display@0 to display0 since no reg under it. Rename mode0
to timing0.
Fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/ls/ls1021a-iot.dtb: dcu@2ce0000 (fsl,ls1021a-dcu): 'display', 'display@0' do not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/display/fsl,ls1021a-dcu.yaml
arch/arm/boot/dts/nxp/ls/ls1021a-iot.dtb: display-timings: 'mode0' does not match any of the regexes: '^pinctrl-[0-9]+$', '^timing'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
default-state = "on" is wrong copied from gpio-leds nodes. Remove it to fix
below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/ls/ls1021a-moxa-uc-8410a.dtb: gpio-keys (gpio-keys): pushbtn-key: Unevaluated properties are not allowed ('default-state' was unexpected)
from schema $id: http://devicetree.org/schemas/input/gpio-keys.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
spansion,s25fl164k (drivers/mtd/spi-nor/spansion.c) can be identified with
the READ ID opcode (0x9F).
Replace spansion,s25fl164k with jedec,spi-nor to fix below CHECK_DTBS
warnings:
arch/arm/boot/dts/nxp/ls/ls1021a-moxa-uc-8410a.dtb: /soc/spi@1550000/flash@0: failed to match any schema with compatible: ['spansion,s25fl064l', 'spansion,s25fl164k']
So no other known DTB user this dts file and it is fine to broken potential
back compatibility since spansion,s25fl164k already support by use
jedec,spi-nor since 2015 commit 413780d7d7 ("mtd: spi-nor: Add support
for Spansion S25FL164K")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Replace marvell,88e1118 with ethernet-phy-ieee802.3-c22.
In drivers/net/mdio/of_mdio.c
/* The following is a list of PHY compatible strings which appear in
* some DTBs. The compatible string is never matched against a PHY
* driver, so is pointless. We only expect devices which are not PHYs
* to have a compatible string, so they can be matched to an MDIO
* driver. Encourage users to upgrade their DT blobs to remove these.
*/
static const struct of_device_id whitelist_phys[]
Fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/ls/ls1021a-moxa-uc-8410a.dtb: /soc/mdio@2d24000/ethernet-phy@0: failed to match any schema with compatible: ['marvell,88e1118']
No other known DTB user this dts file.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add power-supply for lcd panel to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/ls/ls1021a-twr.dtb: panel (nec,nl4827hc19-05b): 'power-supply' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add led suffix to fix below CHECK_DTBS warnings:
ls1021a-moxa-uc-8410a.dtb: leds (gpio-leds): 'beeper', ... do not match
any of the regexes: '(^led-[0-9a-f]$|led)', '^pinctrl-[0-9]+$'
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add front compatible string "fsl,ls1021aqds-fpga" for on boards FPGA chip
and remove unused property bank-width and device-width, which used for
MTD devices and FPGA is not a MTD devices.
Fix below CHECK_DTBS warning:
rch/arm/boot/dts/nxp/ls/ls1021a-qds.dtb: memory-controller@1530000 (fsl,ifc): board-control@3,0: 'oneOf' conditional failed, one must be fixed:
'bank-width', 'device-width' do not match any of the regexes: '^gpio@[0-9a-f]+$', '^mdio-mux@[a-f0-9,]+$', '^pinctrl-[0-9]+$'
/home/lizhi/source/linux-upstream-pci-ep-arm/arch/arm/boot/dts/nxp/ls/ls1021a-qds.dtb: memory-controller@1530000 (fsl,ifc): board-control@3,0:compatible: 'oneOf' conditional failed, one must be fixed:
['simple-mfd'] is too short
arch/arm/boot/dts/nxp/ls/ls1021a-qds.dtb: memory-controller@1530000 (fsl,ifc): board-control@3,0: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'bank-width', 'compatible', 'device-width', 'mdio-mux@54', 'ranges', 'reg' were unexpected)
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Correct spaces or mix of tabs+spaces into proper tab-indented lines.
No functional impact (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Remove redundant #address-cells and #size-cells for ethernet-switch@1
because children node have not address.
Fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/ls/ls1021a-tsn.dtb: ethernet-switch@1 (nxp,sja1105t): Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
from schema $id: http://devicetree.org/schemas/net/dsa/nxp,sja1105.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename node name esdhc@1560000 to mmc@1560000 to fix below CHECK_DTBS
warnings:
arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a-rgb-cdtech-fc21.dtb: esdhc@1560000 (fsl,ls1021a-esdhc): $nodename:0: 'esdhc@1560000' does not match '^mmc(@.*)?$'
from schema $id: http://devicetree.org/schemas/mmc/fsl,esdhc.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename 'mdio-mux-emi1' to 'mdio-mux@54'.
Add fallback compatible string mdio-mux.
Fix below warning:
arch/arm/boot/dts/nxp/ls/ls1021a-qds.dtb: memory-controller@1530000 (fsl,ifc): board-control@3,0: 'oneOf' conditional failed, one must be fixed:
'bank-width', 'device-width', 'mdio-mux-emi1' do not match any of the regexes: '^mdio-mux@[a-f0-9,]+$', 'pinctrl-[0-9]+'
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename node name nor to flash to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/ls/ls1021a-twr.dtb: memory-controller@1530000 (fsl,ifc): 'nor@0,0' does not match any of the regexes: '(flash|fpga|board-control|cpld)@[a-f0-9]+(,[a-f0-9]+)+$', '^nand@[a-f0-9]+(,[a-f0-9]+)+$', '^pinctrl-[0-9]+$'
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Invoke power-domain.yaml if node name as 'power-control'.
Rcpm actually are not power domain controller. It just control wakeup
capability. So rename it as wakeup-control. Implements the same change
as commit e39f567e1c ("arm64: dts: layerscape: rename rcpm as
wakeup-control from power-control") for arm64 layerscapes.
While at it, also remove superfluous #power-domain-cells
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The touchscreen compatible in the overlays has one extra entry. Remove it
to fix the dtbs_check warning:
touchscreen@38 (edt,edt-ft5406): compatible: ['edt,edt-ft5406', 'edt,edt-ft5x06'] is too long
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The jedec SPI-NOR flash node itself has no partitions, but the partitions
subnode.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to binding doc mmc/fsl,esdhc.yaml and driver
drivers/mmc/host/sdhci-of-esdhc.c, default is big-endian, should
use little-endian for little-endian system. Remove 'big-endian' to fix
below warning:
esdhc@1560000 (fsl,ls1021a-esdhc): Unevaluated properties are not allowed ('big-endian', 'bus-width' were unexpected)
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 7e0685a0c4 ("arm64: dts: ls1012a: fix DWC3 USB VBUS glitch issue")
erroneously added this to ls1021a as well. Despite that apparently the
workaround has already been applied unconditional at
commit a6ba1e4531 ("usb: dwc3: apply snps,host-vbus-glitches workaround unconditionally")
Remove it to fix CHECK_DTBS warning:
usb@3100000 (snps,dwc3): Unevaluated properties are not allowed ('snps,host-vbus-glitches' was unexpected)
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a dedicated compatible for ls1021a. Using it also fixes the
warning regarding big-endian:
arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a.dtb: watchdog@2ad0000 (fsl,imx21-wdt): big-endian: False schema does not allow True
Also remove clock-names which is neither used nor specified.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to binding doc memory-controllers/fsl/fsl,ddr.yaml
and driver drivers/edac/fsl_ddr_edac.c, default is big-endian, should
use little-endian for little-endian system. Remove 'big-endian' to fix
below warning:
arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a.dtb: memory-controller@1080000 (fsl,qoriq-memory-controller): 'big-endian' does not match any of the regexes: '^pinctrl-[0-9]+$'
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
queue-group nodes don't need them anyway as they are inherited from
the corresponding ethernet nodes. Fixes the dtbs_check warning:
ethernet@2d10000 (fsl,etsec2): queue-group@2d10000: '#address-cells', '#size-cells' do not match any of the regexes: '^pinctrl-[0-9]+$'
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing reg property to enet nodes. This fixes the dtbs_check warning:
Warning (unit_address_vs_reg): /soc/ethernet@2d10000: node has a unit name, but no reg or ranges property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RTC nodes are supposed to be named rtc@. Also remove reg-names which is
neither used nor specified.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to bindings Rx DMA channel comes first if Rx & Tx is used.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
0x8390000 is reserved memory, but 0x8380000 is the QSPI base address
in RM. But register have offset of 0x8000, so first 'reg' entry address
is used for node unit address.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Although the GIC base address stated in RM is 0x1400000, the first address
being used is 0x1401000. This is similar to imx6ul.dtsi where the
GIC base address in the RM is 0xa00000 but 0xa01000 being used in DTS.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The card name for ALSA is generated from the model name string and
is limited to 16 characters. Use a shorter name to prevent cutting the
name.
MBLS1021A uses the same audio codec as most i.MX based starter kits
by TQ-Systems. Adjust the sound card model to i.MX based platforms,
as done by commit e6303798b6 ("arm64: dts: imx8mp-tqma8mpql-mba8mpxl:
change sound card model name"). This allows sharing a default asound.conf
in BSP over all the kits.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds an overlay for the supported RGB display CDTech DC44.
DCU graphics chain is configured accordingly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds an overlay for the supported RGB display CDTech FC21.
DCU graphics chain is configured accordingly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds an overlay for the supported LVDS display tianma tm070jvhg33.
The on-board RGB-to-LVDS encoder and DCU graphics chain are configured
accordingly. Add power supply as well, which had been missing all the time.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This add an overlay for using the RGB-to-HDMI bridge.
Note: As DDC is directly connected to general I2C bus, there might be I2C
address conflicts. Hence not all displays might work.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(Q)SPI NOR flash is supplied by 3.3V. Add the corresponding supply.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With commit 784bdc6f26 ("ARM: dts: ls1021a: change to use SPDX
identifiers") the SoC .dtsi specifies the license using SPDX tags.
Fix license according to the ls1021a.dtsi this platform DT files
are based on.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- New board support: Apalis eval v1.2 carrier board, Variscite
VAR-SOM-MX93, phyBOARD-Segin-i.MX93.
- A series from Adam Ford to enable bluetooth, configure multiple queues
on eqos, remove unnecessary clock configuration for i.MX8 Beacon boards.
- Several changesets from Alexander Stein to add i.MX8DXP support, enable
audio and GPU for i.MX8QXP, re-parent MEDIA_MIPI_PHY1_REF clock for
i.MX8MP, and improve MBA8xx board description.
- A few dt-schema fixes from Fabio Estevam for i.MX8MM and i.MX93 devices.
- A bunch of changes from Frank Li to improve i.MX8QM and i.MX8DXL
support, correcting edma3 power-domains and interrupt numbers, adding
I2C, FlexCAN and SMMU devices, etc.
- A series from Frieder Schrempf to improve imx8mm-kontron board
descriptions, disabling pulls, fixing up RTC device, adding EEPROM,
and refactoring OSM-S module, etc.
- A set of Data Modul i.MX8M Plus eDM SBC improvements from Marek Vasut.
- A series from Shengjiu Wang to add PDM micphone and SPDIF sound card
support for imx8mm-evk board.
- A series of imx8mm-venice boards improvement from Tim Harvey to add
TPM device, fix USB OTG VBUS etc.
- Other small and random improvements on various boards.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmXb+44UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7XrggAlnkIk0aNw4wTD2OLflPHgE0gD3PR
D2kn+tXx7iUEIv0JM7x4I4aOUOmZIKKSPn1KdJa1kyUAOxgrQR7bs80jsmmmSi57
GvVsAR7F/a7enOW1rQXqrCmWJgckD1d5Lb+z5b4JnkQsqQSbTwiyHwIzkRvlAGHK
zmuN5JSgYt0PKNYd5YylP0uvbnE0aYsDFyRhMxvRYNayb0t1w2gMoGDKc7mHrhXb
84hU9koauUNtzVH2xGH6G2P6PmdOJ6OhQoPIQ+ZCOWvBlAtKzelGGgaySFO3EKAu
RkZXqFi1RDofabwZq+aEXFFY7aNEHwkjLdYj0pFiAPRIhJ7cIrRUAGD+tg==
=7WYT
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=ZRvF
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX arm64 device tree for 6.9:
- New board support: Apalis eval v1.2 carrier board, Variscite
VAR-SOM-MX93, phyBOARD-Segin-i.MX93.
- A series from Adam Ford to enable bluetooth, configure multiple queues
on eqos, remove unnecessary clock configuration for i.MX8 Beacon boards.
- Several changesets from Alexander Stein to add i.MX8DXP support, enable
audio and GPU for i.MX8QXP, re-parent MEDIA_MIPI_PHY1_REF clock for
i.MX8MP, and improve MBA8xx board description.
- A few dt-schema fixes from Fabio Estevam for i.MX8MM and i.MX93 devices.
- A bunch of changes from Frank Li to improve i.MX8QM and i.MX8DXL
support, correcting edma3 power-domains and interrupt numbers, adding
I2C, FlexCAN and SMMU devices, etc.
- A series from Frieder Schrempf to improve imx8mm-kontron board
descriptions, disabling pulls, fixing up RTC device, adding EEPROM,
and refactoring OSM-S module, etc.
- A set of Data Modul i.MX8M Plus eDM SBC improvements from Marek Vasut.
- A series from Shengjiu Wang to add PDM micphone and SPDIF sound card
support for imx8mm-evk board.
- A series of imx8mm-venice boards improvement from Tim Harvey to add
TPM device, fix USB OTG VBUS etc.
- Other small and random improvements on various boards.
* tag 'imx-dt64-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (77 commits)
arm64: dts: imx8mm-kontron-bl-osm-s: Fix Ethernet PHY compatible
arm64: dts: imx8-apalis-v1.1: Remove reset-names from ethernet-phy
arm64: dts: imx8mp-evk: Fix hdmi@3d node
arm64: dts: imx93-var-som: Remove phy-supply from eqos
arm64: dts: imx8mp-phyboard-pollux: Disable pull-up for CD GPIO
arm64: dts: imx8mp-phyboard-pollux: Reduce drive strength for eqos tx lines
arm64: dts: imx8mp-phyboard-pollux: Set debug uart muxing to 0x140
arm64: dts: imx8mp-phyboard-pollux: Add and update rtc devicetree node
arm64: dts: imx8mm-evk: Add spdif sound card support
arm64: dts: mba8xx: Add missing #interrupt-cells
arm64: dts: imx8mp: Set SPI NOR to max 40 MHz on Data Modul i.MX8M Plus eDM SBC
arm64: dts: imx8mn: tqma8mqnl-mba8mx: Add USB DR overlay
arm64: dts: imx8mq: tqma8mq-mba8mx: Add missing USB vbus supply
arm64: dts: freescale: imx8mm/imx8mq: mba8mx: Use PCIe clock generator
arm64: dts: imx8mn-beacon: Remove unnecessary clock configuration
arm64: dts: imx8mn: Slow default video_pll clock rate
arm64: dts: imx8mp-beacon: Configure multiple queues on eqos
arm64: dts: imx8mp-beacon: Enable Bluetooth
arm64: dts: freescale: minor whitespace cleanup
arm64: dts: lx2160a: Fix DTS for full PL011 UART
...
Link: https://lore.kernel.org/r/20240226034147.233993-4-shawnguo2@yeah.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable USB3 HW LPM feature.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix DWC3 USB VBUS glitch issue.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DTS code coding style expects exactly one space before and after '='
sign.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The bootloader does not add the partitions into DT, so add them manually
here.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree for the MBLS102xA mainboard with TQMLS1021A SoM.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.
There's no change to dtbs_install as the flat structure is maintained on
install.
The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
company (e.g. gemini, nspire)
The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
