Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-07-11 (net/intel)
This series contains updates to most Intel network drivers.
Tony removes MODULE_AUTHOR from drivers containing the entry.
Simon Horman corrects a kdoc entry for i40e.
Pawel adds implementation for devlink param "local_forwarding" on ice.
Michal removes unneeded call, and code, for eswitch rebuild for ice.
Sasha removed a no longer used field from igc.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igc: Remove the internal 'eee_advert' field
ice: remove eswitch rebuild
ice: Add support for devlink local_forwarding param
i40e: correct i40e_addr_to_hkey() name in kdoc
net: intel: Remove MODULE_AUTHORs
====================
Link: https://patch.msgid.link/20240711201932.2019925-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
Conflicts:
net/sched/act_ct.c
26488172b0 ("net/sched: Fix UAF when resolving a clash")
3abbd7ed8b ("act_ct: prepare for stolen verdict coming from conntrack and nat engine")
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for driver-specific devlink local_forwarding param.
Supported values are "enabled", "disabled" and "prioritized".
Default configuration is set to "enabled".
Add documentation in networking/devlink/ice.rst.
In previous generations of Intel NICs the transmit scheduler was only
limited by PCIe bandwidth when scheduling/assigning hairpin-bandwidth
between VFs. Changes to E810 HW design introduced scheduler limitation,
so that available hairpin-bandwidth is bound to external port speed.
In order to address this limitation and enable NFV services such as
"service chaining" a knob to adjust the scheduler config was created.
Driver can send a configuration message to the FW over admin queue and
internal FW logic will reconfigure HW to prioritize and add more BW to
VF to VF traffic. An end result, for example, 10G port will no longer
limit hairpin-bandwidth to 10G and much higher speeds can be achieved.
Devlink local_forwarding param set to "prioritized" enables higher
hairpin-bandwitdh on related PFs. Configuration is applicable only to
8x10G and 4x25G cards.
Changing local_forwarding configuration will trigger CORER reset in
order to take effect.
Example command to change current value:
devlink dev param set pci/0000:b2:00.3 name local_forwarding \
value prioritized \
cmode runtime
Co-developed-by: Michal Wilczynski <michal.wilczynski@intel.com>
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Pawel Kaminski <pawel.kaminski@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Correct the example to match the help text from the devlink utility.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing method of reserving unicast filter count leads to wasted
MCAM entries if the functionality is not used or fewer entries are used.
Furthermore, the amount of MCAM entries differs amongst Octeon SoCs.
We implemented a means to adjust the UC filter count via devlink,
allowing for better use of MCAM entries across Netdev apps.
commands:
To get the current unicast filter count
# devlink dev param show pci/0002:02:00.0 name unicast_filter_count
To change/set the unicast filter count
# devlink dev param set pci/0002:02:00.0 name unicast_filter_count
value 5 cmode runtime
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
New driver specific parameter 'tx_scheduling_layers' was introduced.
Describe parameter in the documentation.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Co-developed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support to query scc version by devlink info for device V3.
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://lore.kernel.org/r/20240410125354.2177067-5-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Newer NIC will introduce a new part number, now add it
into devlink device info.
This patch also updates the information of "board.id" in
nfp.rst to match the devlink-info.rst.
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definition and documentation for the new generic
info "board.part_number".
The new one is for part number specific use, and board.id
is modified to match the documentation in devlink-info.
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many devices send event notifications for the IO queues,
such as tx and rx queues, through event queues.
Enable a privileged owner, such as a hypervisor PF, to set the number
of IO event queues for the VF and SF during the provisioning stage.
example:
Get maximum IO event queues of the VF device::
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0 vfnum 1
function:
hw_addr 00:00:00:00:00:00 ipsec_packet disabled max_io_eqs 10
Set maximum IO event queues of the VF device::
$ devlink port function set pci/0000:06:00.0/2 max_io_eqs 32
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0 vfnum 1
function:
hw_addr 00:00:00:00:00:00 ipsec_packet disabled max_io_eqs 32
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide devlink documentation for three eswitch attributes:
mode, inline-mode, and encap-mode.
Signed-off-by: William Tu <witu@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20240325181228.6244-1-witu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Command example string is not read as command.
Fix command annotation.
Fixes: a8ce7b26a5 ("devlink: Expose port function commands to control migratable")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240206161717.466653-1-parav@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix counter name in documentation of mlx5 vnic health reporter diagnose
output: total_error_queues.
While here fix alignment in the documentation file of another counter,
comp_eq_overrun, as it should have its own line and not be part of
another counter's description.
Example:
$ devlink health diagnose pci/0000:00:04.0 reporter vnic
vNIC env counters:
total_error_queues: 0 send_queue_priority_update_flow: 0
comp_eq_overrun: 0 async_eq_overrun: 0 cq_overrun: 0
invalid_command: 0 quota_exceeded_command: 0
nic_receive_steering_discard: 0
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add a note when using esw_port_metadata. The parameter has runtime
mode but setting it does not take effect immediately. Setting it must
happen in legacy mode, and the port metadata takes effects when the
switchdev mode is enabled.
Disable eswitch port metadata::
$ devlink dev param set pci/0000:06:00.0 name esw_port_metadata value \
false cmode runtime
Change eswitch mode to switchdev mode where after choosing the metadata value::
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
Note that other mlx5 devlink runtime parameters, esw_multiport and
flow_steering_mode, do not have this limitation.
Signed-off-by: William Tu <witu@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If Clock Generation Unit is present on NIC board user shall know its
details.
Provide the devlink info callback with a new:
- fixed type object (cgu.id) indicating hardware variant of onboard CGU,
- running type object (fw.cgu) consisting of CGU id, config and firmware
versions.
These information shall be known for debugging purposes.
Test (on NIC board with CGU)
$ devlink dev info <bus_name>/<dev_name> | grep cgu
cgu.id 36
fw.cgu 8032.16973825.6021
Test (on NIC board without CGU)
$ devlink dev info <bus_name>/<dev_name> | grep cgu -c
0
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Be more explicit about devlink entities that may stay and that have to
be removed during reload reinit action.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Align devlink info versions with ice driver so change 'fw.mgmt'
version to be 2-digit version [major.minor], add 'fw.mgmt.build'
that reports mgmt firmware build number and use '"fw.psid.api'
for NVM format version instead of incorrect '"fw.psid'.
Additionally add missing i40e devlink documentation.
Fixes: 5a423552e0 ("i40e: Add handler for devlink .info_get")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231018123558.552453-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a note describing the locking order of taking RTNL lock with devlink
instance lock.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a part talking about nested devlink instances describing
the helpers and locking ordering.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Work from Carlos Bilbao to integrate rustdoc output into the generated
HTML documentation. This took some work to figure out how to do it
without slowing the docs build and without creating people who don't have
Rust installed, but Carlos got there.
- Move the loongarch and mips architecture documentation under
Documentation/arch/.
- Some more maintainer documentation from Jakub
...plus the usual assortment of updates, translations, and fixes.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAmTvqNkPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YgIgH/3drfLtlFtzLqDOzrzDXS8yGnE3pPdxw796b
/ZFzAK16wYKaKevYoIz8bVGGKaE1sEUW0mhlq4KGdfZuxLG8YnWS8URyCW4FDU2E
6qNL+8oJ8LZfID46f9Q8ZgfEz7yF/mhCqPk7MEswYtwbscs2ZTGCTGYB/5BHlBuT
LR+M89uLmHgr8S1o24v30OgiX+VvQFyu0xoxIhbiqUZvBd/XdfX2pgYd9BGzMj5q
C2ZP+V14g36c5pV0EO9TwhCXOF/WVrp7DbjbfWAsqBSLxvpXPydH2q1DUzGeQtP1
exujrBD1O8q3pPdaNA5R+h6cWlHmUZug9mE4BRLp9ErGrozwJsQ=
=C3Uv
-----END PGP SIGNATURE-----
Merge tag 'docs-6.6' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"Documentation work keeps chugging along; this includes:
- Work from Carlos Bilbao to integrate rustdoc output into the
generated HTML documentation. This took some work to figure out how
to do it without slowing the docs build and without creating people
who don't have Rust installed, but Carlos got there
- Move the loongarch and mips architecture documentation under
Documentation/arch/
- Some more maintainer documentation from Jakub
... plus the usual assortment of updates, translations, and fixes"
* tag 'docs-6.6' of git://git.lwn.net/linux: (56 commits)
Docu: genericirq.rst: fix irq-example
input: docs: pxrc: remove reference to phoenix-sim
Documentation: serial-console: Fix literal block marker
docs/mm: remove references to hmm_mirror ops and clean typos
docs/zh_CN: correct regi_chg(),regi_add() to region_chg(),region_add()
Documentation: Fix typos
Documentation/ABI: Fix typos
scripts: kernel-doc: fix macro handling in enums
scripts: kernel-doc: parse DEFINE_DMA_UNMAP_[ADDR|LEN]
Documentation: riscv: Update boot image header since EFI stub is supported
Documentation: riscv: Add early boot document
Documentation: arm: Add bootargs to the table of added DT parameters
docs: kernel-parameters: Refer to the correct bitmap function
doc: update params of memhp_default_state=
docs: Add book to process/kernel-docs.rst
docs: sparse: fix invalid link addresses
docs: vfs: clean up after the iterate() removal
docs: Add a section on surveys to the researcher guidelines
docs: move mips under arch
docs: move loongarch under arch
...
Expose port function commands to enable / disable IPsec packet offloads,
this is used to control the port IPsec capabilities.
When IPsec packet is disabled for a function of the port (default),
function cannot offload IPsec packet operations (encapsulation and XFRM
policy offload). When enabled, IPsec packet operations can be offloaded
by the function of the port, which includes crypto operation
(Encrypt/Decrypt), IPsec encapsulation and XFRM state and policy
offload.
Example of a PCI VF port which supports IPsec packet offloads:
$ devlink port show pci/0000:06:00.0/1
pci/0000:06:00.0/1: type eth netdev enp6s0pf0vf0 flavour pcivf pfnum 0 vfnum 0
function:
hw_addr 00:00:00:00:00:00 roce enable ipsec_packet disable
$ devlink port function set pci/0000:06:00.0/1 ipsec_packet enable
$ devlink port show pci/0000:06:00.0/1
pci/0000:06:00.0/1: type eth netdev enp6s0pf0vf0 flavour pcivf pfnum 0 vfnum 0
function:
hw_addr 00:00:00:00:00:00 roce enable ipsec_packet enable
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20230825062836.103744-3-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expose port function commands to enable / disable IPsec crypto offloads,
this is used to control the port IPsec capabilities.
When IPsec crypto is disabled for a function of the port (default),
function cannot offload any IPsec crypto operations (Encrypt/Decrypt and
XFRM state offloading). When enabled, IPsec crypto operations can be
offloaded by the function of the port.
Example of a PCI VF port which supports IPsec crypto offloads:
$ devlink port show pci/0000:06:00.0/1
pci/0000:06:00.0/1: type eth netdev enp6s0pf0vf0 flavour pcivf pfnum 0 vfnum 0
function:
hw_addr 00:00:00:00:00:00 roce enable ipsec_crypto disable
$ devlink port function set pci/0000:06:00.0/1 ipsec_crypto enable
$ devlink port show pci/0000:06:00.0/1
pci/0000:06:00.0/1: type eth netdev enp6s0pf0vf0 flavour pcivf pfnum 0 vfnum 0
function:
hw_addr 00:00:00:00:00:00 roce enable ipsec_crypto enable
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20230825062836.103744-2-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A new check for the tx devlink health reporter is introduced for
determining when the PTP port timestamping SQ is considered unhealthy. If
there are enough CQEs considered never to be delivered, the space that can
be utilized on the SQ decreases significantly, impacting performance and
usability of the SQ. The health reporter is triggered when the number of
likely never delivered port timestamping CQEs that utilize the space of the
PTP SQ is greater than 93.75% of the total capacity of the SQ. A devlink
health reporter recover method is also provided for this specific TX error
context that restarts the PTP SQ.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
De-duplicate documentation by removing mellanox/mlx5/devlink.rst. Instead,
only use the generic devlink documentation directory to document mlx5
devlink parameters. Avoid providing general devlink tool usage information
in mlx5-specific documentation.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Commit e523af4ee5 ("net/ice: Add support for enable_iwarp and enable_roce
devlink param") added support for the enable_roce and enable_iwarp
parameters in the ice driver. It didn't document these parameters in the
ice devlink documentation file. Add this documentation, including a note
about the mutual exclusion between the two modes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230414162614.571861-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We refer to a TC NIC rule that involves forwarding as "hairpin".
Hairpin queues are mlx5 hardware specific implementation for hardware
forwarding of such packets.
Per the discussion in [1], move the hairpin queues control (number and
size) from debugfs to devlink.
Expose two devlink params:
- hairpin_num_queues: control the number of hairpin queues
- hairpin_queue_size: control the size (in packets) of the hairpin queues
[1] https://lore.kernel.org/all/20230111194608.7f15b9a1@kernel.org/
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20230314054234.267365-12-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add devlink info support for ef100. The information reported is obtained
through the MCDI interface with the specific meaning defined in new
documentation file.
Signed-off-by: Alejandro Lucero <alejandro.lucero-palau@amd.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
1) From Roi and Mark: MultiPort eswitch support
MultiPort E-Switch builds on newer hardware's capabilities and introduces
a mode where a single E-Switch is used and all the vports and physical
ports on the NIC are connected to it.
The new mode will allow in the future a decrease in the memory used by the
driver and advanced features that aren't possible today.
This represents a big change in the current E-Switch implantation in mlx5.
Currently, by default, each E-Switch manager manages its E-Switch.
Steering rules in each E-Switch can only forward traffic to the native
physical port associated with that E-Switch. While there are ways to target
non-native physical ports, for example using a bond or via special TC
rules. None of the ways allows a user to configure the driver
to operate by default in such a mode nor can the driver decide
to move to this mode by default as it's user configuration-driven right now.
While MultiPort E-Switch single FDB mode is the preferred mode, older
generations of ConnectX hardware couldn't support this mode so it was never
implemented. Now that there is capable hardware present, start the
transition to having this mode by default.
Introduce a devlink parameter to control MultiPort Eswitch single FDB mode.
This will allow users to select this mode on their system right now
and in the future will allow the driver to move to this mode by default.
2) From Jiri: Improvements and fixes for mlx5 netdev's devlink logic
2.1) Cleanups related to mlx5's devlink port logic
2.2) Move devlink port registration to be done before netdev alloc
2.3) Create auxdev devlink instance in the same ns as parent devlink
2.4) Suspend auxiliary devices only in case of PCI device suspend
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmPsBlsACgkQSD+KveBX
+j6izAgAtvzimjzOqI8J0FKPW3piRH3VtNWUrlGAf4HHPI0lZMbEV5GIaSI15JeH
wrIpNXKzaA+6+NZ7TzTwqVO+zyKCQVpRw7xPANIJ2A5dId36jU2AgW06zgzFuYWa
mXKG8rAUls6E5a5DHTaY/SueWMO9KMOfLzHFXHNsLAKTAw+FoDdlGso5vgvsy44g
2/N/kDBdzC5n8og934sM7JymthnTVyuGe/Au2w1UUR1MMZ46OQgmhStDwqS5MrzI
pIi+tWFG9YFM5/J8d13y7X/xMCq26Aw6SZSUhsRfTk0goy0uKaU6yYm8vSbO0mci
+e0c8bpWL/MzAhMzWj8CwBPeO6knOw==
=tYc2
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2023-02-10' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2023-02-10
1) From Roi and Mark: MultiPort eswitch support
MultiPort E-Switch builds on newer hardware's capabilities and introduces
a mode where a single E-Switch is used and all the vports and physical
ports on the NIC are connected to it.
The new mode will allow in the future a decrease in the memory used by the
driver and advanced features that aren't possible today.
This represents a big change in the current E-Switch implantation in mlx5.
Currently, by default, each E-Switch manager manages its E-Switch.
Steering rules in each E-Switch can only forward traffic to the native
physical port associated with that E-Switch. While there are ways to target
non-native physical ports, for example using a bond or via special TC
rules. None of the ways allows a user to configure the driver
to operate by default in such a mode nor can the driver decide
to move to this mode by default as it's user configuration-driven right now.
While MultiPort E-Switch single FDB mode is the preferred mode, older
generations of ConnectX hardware couldn't support this mode so it was never
implemented. Now that there is capable hardware present, start the
transition to having this mode by default.
Introduce a devlink parameter to control MultiPort Eswitch single FDB mode.
This will allow users to select this mode on their system right now
and in the future will allow the driver to move to this mode by default.
2) From Jiri: Improvements and fixes for mlx5 netdev's devlink logic
2.1) Cleanups related to mlx5's devlink port logic
2.2) Move devlink port registration to be done before netdev alloc
2.3) Create auxdev devlink instance in the same ns as parent devlink
2.4) Suspend auxiliary devices only in case of PCI device suspend
* tag 'mlx5-updates-2023-02-10' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Suspend auxiliary devices only in case of PCI device suspend
net/mlx5: Remove "recovery" arg from mlx5_load_one() function
net/mlx5e: Create auxdev devlink instance in the same ns as parent devlink
net/mlx5e: Move devlink port registration to be done before netdev alloc
net/mlx5e: Move dl_port to struct mlx5e_dev
net/mlx5e: Replace usage of mlx5e_devlink_get_dl_port() by netdev->devlink_port
net/mlx5e: Pass mdev to mlx5e_devlink_port_register()
net/mlx5: Remove outdated comment
net/mlx5e: TC, Remove redundant parse_attr argument
net/mlx5e: Use a simpler comparison for uplink rep
net/mlx5: Lag, Add single RDMA device in multiport mode
net/mlx5: Lag, set different uplink vport metadata in multiport eswitch mode
net/mlx5: E-Switch, rename bond update function to be reused
net/mlx5e: TC, Add peer flow in mpesw mode
net/mlx5: Lag, Control MultiPort E-Switch single FDB mode
====================
Link: https://lore.kernel.org/r/20230214221239.159033-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update devlink-health.rst file:
- Add devlink formatted message (fmsg) API documentation.
- Add auto-dump as a condition to do dump once error reported.
- Expand OOB to clarify this acronym.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MultiPort E-Switch builds on newer hardware's capabilities and introduces
a mode where a single E-Switch is used and all the vports and physical
ports on the NIC are connected to it.
The new mode will allow in the future a decrease in the memory used by the
driver and advanced features that aren't possible today.
This represents a big change in the current E-Switch implantation in mlx5.
Currently, by default, each E-Switch manager manages its E-Switch.
Steering rules in each E-Switch can only forward traffic to the native
physical port associated with that E-Switch. While there are ways to target
non-native physical ports, for example using a bond or via special TC
rules. None of the ways allows a user to configure the driver
to operate by default in such a mode nor can the driver decide
to move to this mode by default as it's user configuration-driven right now.
While MultiPort E-Switch single FDB mode is the preferred mode, older
generations of ConnectX hardware couldn't support this mode so it was never
implemented. Now that there is capable hardware present, start the
transition to having this mode by default.
Introduce a devlink parameter to control MultiPort E-Switch single FDB mode.
This will allow users to select this mode on their system right now
and in the future will allow the driver to move to this mode by default.
Example:
$ devlink dev param set pci/0000:00:0b.0 name esw_multiport value 1 \
cmode runtime
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Correct spelling problems for Documentation/networking/ as reported
by codespell.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Cc: Jiri Pirko <jiri@nvidia.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Link: https://lore.kernel.org/r/20230129231053.20863-5-rdunlap@infradead.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
toc entry is missing for etas_es58x devlink doc and triggers this warning:
Documentation/networking/devlink/etas_es58x.rst: WARNING: document isn't included in any toctree
Add the missing toc entry.
Fixes: 9f63f96aac ("Documentation: devlink: add devlink documentation for the etas_es58x driver")
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20221213051136.721887-1-mailhol.vincent@wanadoo.fr
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
List all the version information reported by the etas_es58x driver
through devlink. Also, update MAINTAINERS with the newly created file.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20221130174658.29282-8-mailhol.vincent@wanadoo.fr
[mkl: fixed version information table: "bl" -> "fw.bootloader"
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As discussed in [1], abbreviating the bootloader to "bl" might not be
well understood. Instead, a bootloader technically being a firmware,
name it "fw.bootloader".
Add a new macro to devlink.h to formalize this new info attribute name
and update the documentation.
[1] https://lore.kernel.org/netdev/20221128142723.2f826d20@kernel.org/
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20221130174658.29282-5-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Expose port function commands to enable / disable migratable
capability, this is used to set the port function as migratable.
Live migration is the process of transferring a live virtual machine
from one physical host to another without disrupting its normal
operation.
In order for a VM to be able to perform LM, all the VM components must
be able to perform migration. e.g.: to be migratable.
In order for VF to be migratable, VF must be bound to VFIO driver with
migration support.
When migratable capability is enabled for a function of the port, the
device is making the necessary preparations for the function to be
migratable, which might include disabling features which cannot be
migrated.
Example of LM with migratable function configuration:
Set migratable of the VF's port function.
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 migratable disable
$ devlink port function set pci/0000:06:00.0/2 migratable enable
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 migratable enable
Bind VF to VFIO driver with migration support:
$ echo <pci_id> > /sys/bus/pci/devices/0000:08:00.0/driver/unbind
$ echo mlx5_vfio_pci > /sys/bus/pci/devices/0000:08:00.0/driver_override
$ echo <pci_id> > /sys/bus/pci/devices/0000:08:00.0/driver/bind
Attach VF to the VM.
Start the VM.
Perform LM.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expose port function commands to enable / disable RoCE, this is used to
control the port RoCE device capabilities.
When RoCE is disabled for a function of the port, function cannot create
any RoCE specific resources (e.g GID table).
It also saves system memory utilization. For example disabling RoCE enable a
VF/SF saves 1 Mbytes of system memory per function.
Example of a PCI VF port which supports function configuration:
Set RoCE of the VF's port function.
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 roce enable
$ devlink port function set pci/0000:06:00.0/2 roce disable
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev enp6s0pf0vf1 flavour pcivf pfnum 0
vfnum 1
function:
hw_addr 00:00:00:00:00:00 roce disable
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
devlink port function hw_addr attr documentation is in mlx5 specific
file while there is nothing mlx5 specific about it.
Move it to devlink-port.rst.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .read handler for the NVM and Shadow RAM regions. This
enables user space to read a small chunk of the flash without needing the
overhead of creating a full snapshot.
Update the documentation for ice to detail which regions have direct read
support.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
78ad87da99 ("ice: devlink: add shadow-ram region to snapshot Shadow RAM")
added support for the 'shadow-ram' devlink region, but did not document it
in the ice devlink documentation. Fix this.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To read from a region, user space must currently request a new snapshot of
the region and then read from that snapshot. This can sometimes be overkill
if user space only reads a tiny portion. They first create the snapshot,
then request a read, then destroy the snapshot.
For regions which have a single underlying "contents", it makes sense to
allow supporting direct reading of the region data.
Extend the DEVLINK_CMD_REGION_READ to allow direct reading from a region if
requested via the new DEVLINK_ATTR_REGION_DIRECT. If this attribute is set,
then perform a direct read instead of using a snapshot. Direct read is
mutually exclusive with DEVLINK_ATTR_REGION_SNAPSHOT_ID, and care is taken
to ensure that we reject commands which provide incorrect attributes.
Regions must enable support for direct read by implementing the .read()
callback function. If a region does not support such direct reads, a
suitable extended error message is reported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kernel test robot reported indentation warnings:
Documentation/networking/devlink/devlink-port.rst:220: WARNING: Unexpected indentation.
Documentation/networking/devlink/devlink-port.rst:222: WARNING: Block quote ends without a blank line; unexpected unindent.
These warnings cause lists (arbitration flow for which the warnings blame to
and 3-step subfunction setup) to be rendered inline instead. Also, for the
former list, automatic list numbering is messed up.
Fix these warnings by adding missing blank line padding.
Link: https://lore.kernel.org/linux-doc/202211200926.kfOPiVti-lkp@intel.com/
Fixes: 242dd64375 ("Documentation: Add documentation for new devlink-rate attributes")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide documentation for newly introduced netlink attributes for
devlink-rate: tx_priority and tx_weight.
Mention the possibility to export tree from the driver.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add documentation to a newly added devlink-rate feature. Provide some
examples on how to use the commands, which netlink attributes are
supported and descriptions of the attributes.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add packet traps for 802.1X operation. The "eapol" control trap is used
to trap EAPOL packets and is required for the correct operation of the
control plane. The "locked_port" drop trap can be enabled to gain
visibility into packets that were dropped by the device due to the
locked bridge port check.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change occurrences of "it's" that are possessive to "its"
so that they don't read as "it is".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20220829235414.17110-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-08-24 (ice)
This series contains updates to ice driver only.
Marcin adds support for TC parsing on TTL and ToS fields.
Anatolli adds support for devlink port split command to allow
configuration of various port configurations.
Jake allows for passing and writing an additional NVM write activate
field by expanding current cmd_flag.
Ani makes PHY debug output more readable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As all callbacks are converted now, fix the text reflecting that change.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20220823070213.1008956-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow to configure port split options using the devlink port split
interface. Support port splitting only for port 0, as the FW has
a predefined set of available port split options for the whole device.
Add ice_devlink_port_options_print() function to print the table with
all available FW port split options. It will be printed after each port
split and unsplit command.
Add documentation for devlink port split interface usage for the ice
driver.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Document the t7xx devlink commands usage for fw flashing &
coredump collection.
Refer to t7xx.rst file for details.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: Devegowda Chandrashekar <chandrashekar.devegowda@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a framework for running selftests.
Framework exposes devlink commands and test suite(s) to the user
to execute and query the supported tests by the driver.
Below are new entries in devlink_nl_ops
devlink_nl_cmd_selftests_show_doit/dumpit: To query the supported
selftests by the drivers.
devlink_nl_cmd_selftests_run: To execute selftests. Users can
provide a test mask for executing group tests or standalone tests.
Documentation/networking/devlink/ path is already part of MAINTAINERS &
the new files come under this path. Hence no update needed to the
MAINTAINERS
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use tunneled MGIR to obtain PSID of line card device and extend
device_info_get() op to fill up the info with that.
Example:
$ devlink dev info auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0:
versions:
fixed:
hw.revision 0
fw.psid MT_0000000749
running:
ini.version 4
fw 19.2010.1312
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case the line card is active, go over all possible existing
devices (gearboxes) on it and expose FW version of the flashable one.
Example:
$ devlink dev info auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0:
versions:
fixed:
hw.revision 0
running:
ini.version 4
fw 19.2010.1312
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement info_get() to expose HW revision of a linecard and loaded INI
version.
Example:
$ devlink dev info auxiliary/mlxsw_core.lc.0
auxiliary/mlxsw_core.lc.0:
versions:
fixed:
hw.revision 0
running:
ini.version 4
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend MDDQ to obtain FW version of line card device and implement
device_info_get() op to fill up the info with that.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement info_get() to expose HW revision of a linecard and loaded INI
version.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the driver to provide per line card info get op to fill-up info,
similar to the "devlink dev info".
Example:
$ devlink lc info pci/0000:01:00.0 lc 8
pci/0000:01:00.0:
lc 8
versions:
fixed:
hw.revision 0
running:
ini.version 4
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow driver to mark a line card as active. Expose this state to the
userspace over devlink netlink interface with proper notifications.
'active' state means that line card was plugged in after
being provisioned.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be able to configure all needed stuff on a port/netdevice
of a line card without the line card being present, introduce line card
provisioning. Basically by setting a type, provisioning process will
start and driver is supposed to create a placeholder for instances
(ports/netdevices) for a line card type.
Allow the user to query the supported line card types over line card
get command. Then implement two netlink command SET to allow user to
set/unset the card type.
On the driver API side, add provision/unprovision ops and supported
types array to be advertised. Upon provision op call, the driver should
take care of creating the instances for the particular line card type.
Introduce provision_set/clear() functions to be called by the driver
once the provisioning/unprovisioning is done on its side. These helpers
are not to be called directly due to the async nature of provisioning.
Example:
$ devlink port # No ports are listed
$ devlink lc
pci/0000:01:00.0:
lc 1 state unprovisioned
supported_types:
16x100G
lc 2 state unprovisioned
supported_types:
16x100G
lc 3 state unprovisioned
supported_types:
16x100G
lc 4 state unprovisioned
supported_types:
16x100G
lc 5 state unprovisioned
supported_types:
16x100G
lc 6 state unprovisioned
supported_types:
16x100G
lc 7 state unprovisioned
supported_types:
16x100G
lc 8 state unprovisioned
supported_types:
16x100G
$ devlink lc set pci/0000:01:00.0 lc 8 type 16x100G
$ devlink lc show pci/0000:01:00.0 lc 8
pci/0000:01:00.0:
lc 8 state active type 16x100G
supported_types:
16x100G
$ devlink port
pci/0000:01:00.0/0: type notset flavour cpu port 0 splittable false
pci/0000:01:00.0/53: type eth netdev enp1s0nl8p1 flavour physical lc 8 port 1 splittable true lanes 4
pci/0000:01:00.0/54: type eth netdev enp1s0nl8p2 flavour physical lc 8 port 2 splittable true lanes 4
pci/0000:01:00.0/55: type eth netdev enp1s0nl8p3 flavour physical lc 8 port 3 splittable true lanes 4
pci/0000:01:00.0/56: type eth netdev enp1s0nl8p4 flavour physical lc 8 port 4 splittable true lanes 4
pci/0000:01:00.0/57: type eth netdev enp1s0nl8p5 flavour physical lc 8 port 5 splittable true lanes 4
pci/0000:01:00.0/58: type eth netdev enp1s0nl8p6 flavour physical lc 8 port 6 splittable true lanes 4
pci/0000:01:00.0/59: type eth netdev enp1s0nl8p7 flavour physical lc 8 port 7 splittable true lanes 4
pci/0000:01:00.0/60: type eth netdev enp1s0nl8p8 flavour physical lc 8 port 8 splittable true lanes 4
pci/0000:01:00.0/61: type eth netdev enp1s0nl8p9 flavour physical lc 8 port 9 splittable true lanes 4
pci/0000:01:00.0/62: type eth netdev enp1s0nl8p10 flavour physical lc 8 port 10 splittable true lanes 4
pci/0000:01:00.0/63: type eth netdev enp1s0nl8p11 flavour physical lc 8 port 11 splittable true lanes 4
pci/0000:01:00.0/64: type eth netdev enp1s0nl8p12 flavour physical lc 8 port 12 splittable true lanes 4
pci/0000:01:00.0/125: type eth netdev enp1s0nl8p13 flavour physical lc 8 port 13 splittable true lanes 4
pci/0000:01:00.0/126: type eth netdev enp1s0nl8p14 flavour physical lc 8 port 14 splittable true lanes 4
pci/0000:01:00.0/127: type eth netdev enp1s0nl8p15 flavour physical lc 8 port 15 splittable true lanes 4
pci/0000:01:00.0/128: type eth netdev enp1s0nl8p16 flavour physical lc 8 port 16 splittable true lanes 4
$ devlink lc set pci/0000:01:00.0 lc 8 notype
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should be familiar and beneficial to expose devlink instance
lock to the drivers. This way drivers can block devlink from
calling them during critical sections without breakneck locking.
Add port helpers, port splitting callbacks will be the first
target.
Use 'devl_' prefix for "explicitly locked" API. Initial RFC used
'__devlink' but that's too much typing.
devl_lock_is_held() is not defined without lockdep, which is
the same behavior as lockdep_is_held() itself.
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the following build warning:
Documentation/networking/devlink/mlx5.rst:13: WARNING: Error parsing content block for the "list-table" directive:
+uniform two-level bullet list expected, but row 2 does not contain the same number of items as row 1 (2 vs 3).
...
Add the missing item in the first row.
Fixes: 0844fa5f7b ("net/mlx5: Let user configure io_eq_size param")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, max_macs is taking 70Kbytes of memory per function. This
size is not needed in all use cases, and is critical with large scale.
Hence, allow user to configure the number of max_macs.
For example, to reduce the number of max_macs to 1, execute::
$ devlink dev param set pci/0000:00:0b.0 name max_macs value 1 \
cmode driverinit
$ devlink dev reload pci/0000:00:0b.0
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Event EQ is an EQ which received the notification of almost all the
events generated by the NIC.
Currently, each event EQ is taking 512KB of memory. This size is not
needed in most use cases, and is critical with large scale. Hence,
allow user to configure the size of the event EQ.
For example to reduce event EQ size to 64, execute::
$ devlink dev param set pci/0000:00:0b.0 name event_eq_size value 64 \
cmode driverinit
$ devlink dev reload pci/0000:00:0b.0
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add new device generic parameter to determine the size of the
asynchronous control events EQ.
For example, to reduce event EQ size to 64, execute:
$ devlink dev param set pci/0000:06:00.0 \
name event_eq_size value 64 cmode driverinit
$ devlink dev reload pci/0000:06:00.0
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, each I/O EQ is taking 128KB of memory. This size
is not needed in all use cases, and is critical with large scale.
Hence, allow user to configure the size of I/O EQs.
For example, to reduce I/O EQ size to 64, execute:
$ devlink dev param set pci/0000:00:0b.0 name io_eq_size value 64 \
cmode driverinit
$ devlink dev reload pci/0000:00:0b.0
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add new device generic parameter to determine the size of the
I/O completion EQs.
For example, to reduce I/O EQ size to 64, execute:
$ devlink dev param set pci/0000:06:00.0 \
name io_eq_size value 64 cmode driverinit
$ devlink dev reload pci/0000:06:00.0
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The ice hardware contains an embedded chip with firmware which can be
updated using devlink flash. The firmware which runs on this chip is
referred to as the Embedded Management Processor firmware (EMP
firmware).
Activating the new firmware image currently requires that the system be
rebooted. This is not ideal as rebooting the system can cause unwanted
downtime.
In practical terms, activating the firmware does not always require a
full system reboot. In many cases it is possible to activate the EMP
firmware immediately. There are a couple of different scenarios to
cover.
* The EMP firmware itself can be reloaded by issuing a special update
to the device called an Embedded Management Processor reset (EMP
reset). This reset causes the device to reset and reload the EMP
firmware.
* PCI configuration changes are only reloaded after a cold PCIe reset.
Unfortunately there is no generic way to trigger this for a PCIe
device without a system reboot.
When performing a flash update, firmware is capable of responding with
some information about the specific update requirements.
The driver updates the flash by programming a secondary inactive bank
with the contents of the new image, and then issuing a command to
request to switch the active bank starting from the next load.
The response to the final command for updating the inactive NVM flash
bank includes an indication of the minimum reset required to fully
update the device. This can be one of the following:
* A full power on is required
* A cold PCIe reset is required
* An EMP reset is required
The response to the command to switch flash banks includes an indication
of whether or not the firmware will allow an EMP reset request.
For most updates, an EMP reset is sufficient to load the new EMP
firmware without issues. In some cases, this reset is not sufficient
because the PCI configuration space has changed. When this could cause
incompatibility with the new EMP image, the firmware is capable of
rejecting the EMP reset request.
Add logic to ice_fw_update.c to handle the response data flash update
AdminQ commands.
For the reset level, issue a devlink status notification informing the
user of how to complete the update with a simple suggestion like
"Activate new firmware by rebooting the system".
Cache the status of whether or not firmware will restrict the EMP reset
for use in implementing devlink reload.
Implement support for devlink reload with the "fw_activate" flag. This
allows user space to request the firmware be activated immediately.
For the .reload_down handler, we will issue a request for the EMP reset
using the appropriate firmware AdminQ command. If we know that the
firmware will not allow an EMP reset, simply exit with a suitable
netlink extended ACK message indicating that the EMP reset is not
available.
For the .reload_up handler, simply wait until the driver has finished
resetting. Logic to handle processing of an EMP reset already exists in
the driver as part of its reset and rebuild flows.
Implement support for the devlink reload interface with the
"fw_activate" action. This allows userspace to request activation of
firmware without a reboot.
Note that support for indicating the required reset and EMP reset
restriction is not supported on old versions of firmware. The driver can
determine if the two features are supported by checking the device
capabilities report. I confirmed support has existed since at least
version 5.5.2 as reported by the 'fw.mgmt' version. Support to issue the
EMP reset request has existed in all version of the EMP firmware for the
ice hardware.
Check the device capabilities report to determine whether or not the
indications are reported by the running firmware. If the reset
requirement indication is not supported, always assume a full power on
is necessary. If the reset restriction capability is not supported,
always assume the EMP reset is available.
Users can verify if the EMP reset has activated the firmware by using
the devlink info report to check that the 'running' firmware version has
updated. For example a user might do the following:
# Check current version
$ devlink dev info
# Update the device
$ devlink dev flash pci/0000:af:00.0 file firmware.bin
# Confirm stored version updated
$ devlink dev info
# Reload to activate new firmware
$ devlink dev reload pci/0000:af:00.0 action fw_activate
# Confirm running version updated
$ devlink dev info
Finally, this change does *not* implement basic driver-only reload
support. I did look into trying to do this. However, it requires
significant refactor of how the ice driver probes and loads everything.
The ice driver probe and allocation flows were not designed with such
a reload in mind. Refactoring the flow to support this is beyond the
scope of this change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new device generic parameter to enable and disable
iWARP functionality on a multi-protocol RDMA device.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Leszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add 'enable_remote_dev_reset' documentation to bnxt.rst.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a file to document devlink support for octeontx2
driver. Driver-specific parameters implemented by
AF, PF and VF drivers are documented.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
revert commit 46ae40b94d ("net/mlx5: Let user configure io_eq_size param")
revert commit a6cb08daa3 ("net/mlx5: Let user configure event_eq_size param")
revert commit 5546040619 ("net/mlx5: Let user configure max_macs param")
The EQE parameters are applicable to more drivers, they should
be configured via standard API, probably ethtool. Example of
another driver needing something similar:
https://lore.kernel.org/all/1633454136-14679-3-git-send-email-sbhatta@marvell.com/
The last param for "max_macs" is probably fine but the documentation
is severely lacking. The meaning and implications for changing the
param need to be stated.
Link: https://lore.kernel.org/r/20211026152939.3125950-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, max_macs is taking 70Kbytes of memory per function. This
size is not needed in all use cases, and is critical with large scale.
Hence, allow user to configure the number of max_macs.
For example, to reduce the number of max_macs to 1, execute::
$ devlink dev param set pci/0000:00:0b.0 name max_macs value 1 \
cmode driverinit
$ devlink dev reload pci/0000:00:0b.0
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Event EQ is an EQ which received the notification of almost all the
events generated by the NIC.
Currently, each event EQ is taking 512KB of memory. This size is not
needed in most use cases, and is critical with large scale. Hence,
allow user to configure the size of the event EQ.
For example to reduce event EQ size to 64, execute::
$ devlink resource set pci/0000:00:0b.0 path /event_eq_size/ size 64
$ devlink dev reload pci/0000:00:0b.0
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, each I/O EQ is taking 128KB of memory. This size
is not needed in all use cases, and is critical with large scale.
Hence, allow user to configure the size of I/O EQs.
For example, to reduce I/O EQ size to 64, execute:
$ devlink resource set pci/0000:00:0b.0 path /io_eq_size/ size 64
$ devlink dev reload pci/0000:00:0b.0
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently when a user uses "devlink dev info", the fw.mgmt.api will be
the major.minor numbers as shown below:
devlink dev info pci/0000:3b:00.0
pci/0000:3b:00.0:
driver ice
serial_number 00-01-00-ff-ff-00-00-00
versions:
fixed:
board.id K91258-000
running:
fw.mgmt 6.1.2
fw.mgmt.api 1.7 <--- No patch number included
fw.mgmt.build 0xd75e7d06
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.app.name ICE OS Default Package
fw.app 1.3.27.0
fw.app.bundle_id 0xc0000001
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
stored:
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
There are many features in the driver that depend on the major, minor,
and patch version of the FW. Without the patch number in the output for
fw.mgmt.api debugging issues related to the FW API version is difficult.
Also, using major.minor.patch aligns with the existing firmware version
which uses a 3 digit value.
Fix this by making the fw.mgmt.api print the major.minor.patch
versions. Shown below is the result:
devlink dev info pci/0000:3b:00.0
pci/0000:3b:00.0:
driver ice
serial_number 00-01-00-ff-ff-00-00-00
versions:
fixed:
board.id K91258-000
running:
fw.mgmt 6.1.2
fw.mgmt.api 1.7.9 <--- patch number included
fw.mgmt.build 0xd75e7d06
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.app.name ICE OS Default Package
fw.app 1.3.27.0
fw.app.bundle_id 0xc0000001
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
stored:
fw.mgmt.srev 5
fw.undi 1.2992.0
fw.undi.srev 5
fw.psid.api 3.10
fw.bundle_id 0x800085cc
fw.netlist 3.10.2000-3.1e.0
fw.netlist.build 0x2a76e110
Fixes: ff2e5c700e ("ice: add basic handler for devlink .info_get")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
1. Removed driver specific extra params like download_region,
address & region_count. The required information is passed
as part of flash API.
2. IOSM Devlink documentation updated to reflect the same.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each region has an independently configurable number of maximum
snapshots. This information is not reported to userspace, making it not
very discoverable. Fix this by adding a new
DEVLINK_ATTR_REGION_MAX_SNAPSHOST attribute which is used to report this
maximum.
Ex:
$devlink region
pci/0000:af:00.0/nvm-flash: size 10485760 snapshot [] max 1
pci/0000:af:00.0/device-caps: size 4096 snapshot [] max 10
pci/0000:af:00.1/nvm-flash: size 10485760 snapshot [] max 1
pci/0000:af:00.1/device-caps: size 4096 snapshot [] max 10
This information enables users to understand why a new region command
may fail due to having too many existing snapshots.
Reported-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documents devlink params, fw update & cd collection commands
and its usage.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver has removed its devlink params, so there is nothing
to see here.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new device generic parameter to enable/disable creation of
VDPA net auxiliary device and associated device functionality
in the devlink instance.
User who prefers to disable such functionality can disable it using below
example.
$ devlink dev param set pci/0000:06:00.0 \
name enable_vnet value false cmode driverinit
$ devlink dev reload pci/0000:06:00.0
At this point devlink instance do not create auxiliary device for the
VDPA net functionality.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new device generic parameter to enable/disable creation of
RDMA auxiliary device and associated device functionality
in the devlink instance.
User who prefers to disable such functionality can disable it using below
example.
$ devlink dev param set pci/0000:06:00.0 \
name enable_rdma value false cmode driverinit
$ devlink dev reload pci/0000:06:00.0
At this point devlink instance do not create auxiliary device for the
RDMA functionality.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new device generic parameter to enable/disable creation of
Ethernet auxiliary device and associated device functionality
in the devlink instance.
User who prefers to disable such functionality can disable it using below
example.
$ devlink dev param set pci/0000:06:00.0 \
name enable_eth value false cmode driverinit
$ devlink dev reload pci/0000:06:00.0
At this point devlink instance do not create auxiliary device for the
Ethernet functionality.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a file to document devlink support for hns3 driver, now support devlink
info and devlink reload.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core:
- BPF:
- add syscall program type and libbpf support for generating
instructions and bindings for in-kernel BPF loaders (BPF loaders
for BPF), this is a stepping stone for signed BPF programs
- infrastructure to migrate TCP child sockets from one listener
to another in the same reuseport group/map to improve flexibility
of service hand-off/restart
- add broadcast support to XDP redirect
- allow bypass of the lockless qdisc to improving performance
(for pktgen: +23% with one thread, +44% with 2 threads)
- add a simpler version of "DO_ONCE()" which does not require
jump labels, intended for slow-path usage
- virtio/vsock: introduce SOCK_SEQPACKET support
- add getsocketopt to retrieve netns cookie
- ip: treat lowest address of a IPv4 subnet as ordinary unicast address
allowing reclaiming of precious IPv4 addresses
- ipv6: use prandom_u32() for ID generation
- ip: add support for more flexible field selection for hashing
across multi-path routes (w/ offload to mlxsw)
- icmp: add support for extended RFC 8335 PROBE (ping)
- seg6: add support for SRv6 End.DT46 behavior
- mptcp:
- DSS checksum support (RFC 8684) to detect middlebox meddling
- support Connection-time 'C' flag
- time stamping support
- sctp: packetization Layer Path MTU Discovery (RFC 8899)
- xfrm: speed up state addition with seq set
- WiFi:
- hidden AP discovery on 6 GHz and other HE 6 GHz improvements
- aggregation handling improvements for some drivers
- minstrel improvements for no-ack frames
- deferred rate control for TXQs to improve reaction times
- switch from round robin to virtual time-based airtime scheduler
- add trace points:
- tcp checksum errors
- openvswitch - action execution, upcalls
- socket errors via sk_error_report
Device APIs:
- devlink: add rate API for hierarchical control of max egress rate
of virtual devices (VFs, SFs etc.)
- don't require RCU read lock to be held around BPF hooks
in NAPI context
- page_pool: generic buffer recycling
New hardware/drivers:
- mobile:
- iosm: PCIe Driver for Intel M.2 Modem
- support for Qualcomm MSM8998 (ipa)
- WiFi: Qualcomm QCN9074 and WCN6855 PCI devices
- sparx5: Microchip SparX-5 family of Enterprise Ethernet switches
- Mellanox BlueField Gigabit Ethernet (control NIC of the DPU)
- NXP SJA1110 Automotive Ethernet 10-port switch
- Qualcomm QCA8327 switch support (qca8k)
- Mikrotik 10/25G NIC (atl1c)
Driver changes:
- ACPI support for some MDIO, MAC and PHY devices from Marvell and NXP
(our first foray into MAC/PHY description via ACPI)
- HW timestamping (PTP) support: bnxt_en, ice, sja1105, hns3, tja11xx
- Mellanox/Nvidia NIC (mlx5)
- NIC VF offload of L2 bridging
- support IRQ distribution to Sub-functions
- Marvell (prestera):
- add flower and match all
- devlink trap
- link aggregation
- Netronome (nfp): connection tracking offload
- Intel 1GE (igc): add AF_XDP support
- Marvell DPU (octeontx2): ingress ratelimit offload
- Google vNIC (gve): new ring/descriptor format support
- Qualcomm mobile (rmnet & ipa): inline checksum offload support
- MediaTek WiFi (mt76)
- mt7915 MSI support
- mt7915 Tx status reporting
- mt7915 thermal sensors support
- mt7921 decapsulation offload
- mt7921 enable runtime pm and deep sleep
- Realtek WiFi (rtw88)
- beacon filter support
- Tx antenna path diversity support
- firmware crash information via devcoredump
- Qualcomm 60GHz WiFi (wcn36xx)
- Wake-on-WLAN support with magic packets and GTK rekeying
- Micrel PHY (ksz886x/ksz8081): add cable test support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=LvtX
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- BPF:
- add syscall program type and libbpf support for generating
instructions and bindings for in-kernel BPF loaders (BPF loaders
for BPF), this is a stepping stone for signed BPF programs
- infrastructure to migrate TCP child sockets from one listener to
another in the same reuseport group/map to improve flexibility
of service hand-off/restart
- add broadcast support to XDP redirect
- allow bypass of the lockless qdisc to improving performance (for
pktgen: +23% with one thread, +44% with 2 threads)
- add a simpler version of "DO_ONCE()" which does not require jump
labels, intended for slow-path usage
- virtio/vsock: introduce SOCK_SEQPACKET support
- add getsocketopt to retrieve netns cookie
- ip: treat lowest address of a IPv4 subnet as ordinary unicast
address allowing reclaiming of precious IPv4 addresses
- ipv6: use prandom_u32() for ID generation
- ip: add support for more flexible field selection for hashing
across multi-path routes (w/ offload to mlxsw)
- icmp: add support for extended RFC 8335 PROBE (ping)
- seg6: add support for SRv6 End.DT46 behavior
- mptcp:
- DSS checksum support (RFC 8684) to detect middlebox meddling
- support Connection-time 'C' flag
- time stamping support
- sctp: packetization Layer Path MTU Discovery (RFC 8899)
- xfrm: speed up state addition with seq set
- WiFi:
- hidden AP discovery on 6 GHz and other HE 6 GHz improvements
- aggregation handling improvements for some drivers
- minstrel improvements for no-ack frames
- deferred rate control for TXQs to improve reaction times
- switch from round robin to virtual time-based airtime scheduler
- add trace points:
- tcp checksum errors
- openvswitch - action execution, upcalls
- socket errors via sk_error_report
Device APIs:
- devlink: add rate API for hierarchical control of max egress rate
of virtual devices (VFs, SFs etc.)
- don't require RCU read lock to be held around BPF hooks in NAPI
context
- page_pool: generic buffer recycling
New hardware/drivers:
- mobile:
- iosm: PCIe Driver for Intel M.2 Modem
- support for Qualcomm MSM8998 (ipa)
- WiFi: Qualcomm QCN9074 and WCN6855 PCI devices
- sparx5: Microchip SparX-5 family of Enterprise Ethernet switches
- Mellanox BlueField Gigabit Ethernet (control NIC of the DPU)
- NXP SJA1110 Automotive Ethernet 10-port switch
- Qualcomm QCA8327 switch support (qca8k)
- Mikrotik 10/25G NIC (atl1c)
Driver changes:
- ACPI support for some MDIO, MAC and PHY devices from Marvell and
NXP (our first foray into MAC/PHY description via ACPI)
- HW timestamping (PTP) support: bnxt_en, ice, sja1105, hns3, tja11xx
- Mellanox/Nvidia NIC (mlx5)
- NIC VF offload of L2 bridging
- support IRQ distribution to Sub-functions
- Marvell (prestera):
- add flower and match all
- devlink trap
- link aggregation
- Netronome (nfp): connection tracking offload
- Intel 1GE (igc): add AF_XDP support
- Marvell DPU (octeontx2): ingress ratelimit offload
- Google vNIC (gve): new ring/descriptor format support
- Qualcomm mobile (rmnet & ipa): inline checksum offload support
- MediaTek WiFi (mt76)
- mt7915 MSI support
- mt7915 Tx status reporting
- mt7915 thermal sensors support
- mt7921 decapsulation offload
- mt7921 enable runtime pm and deep sleep
- Realtek WiFi (rtw88)
- beacon filter support
- Tx antenna path diversity support
- firmware crash information via devcoredump
- Qualcomm WiFi (wcn36xx)
- Wake-on-WLAN support with magic packets and GTK rekeying
- Micrel PHY (ksz886x/ksz8081): add cable test support"
* tag 'net-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2168 commits)
tcp: change ICSK_CA_PRIV_SIZE definition
tcp_yeah: check struct yeah size at compile time
gve: DQO: Fix off by one in gve_rx_dqo()
stmmac: intel: set PCI_D3hot in suspend
stmmac: intel: Enable PHY WOL option in EHL
net: stmmac: option to enable PHY WOL with PMT enabled
net: say "local" instead of "static" addresses in ndo_dflt_fdb_{add,del}
net: use netdev_info in ndo_dflt_fdb_{add,del}
ptp: Set lookup cookie when creating a PTP PPS source.
net: sock: add trace for socket errors
net: sock: introduce sk_error_report
net: dsa: replay the local bridge FDB entries pointing to the bridge dev too
net: dsa: ensure during dsa_fdb_offload_notify that dev_hold and dev_put are on the same dev
net: dsa: include fdb entries pointing to bridge in the host fdb list
net: dsa: include bridge addresses which are local in the host fdb list
net: dsa: sync static FDB entries on foreign interfaces to hardware
net: dsa: install the host MDB and FDB entries in the master's RX filter
net: dsa: reference count the FDB addresses at the cross-chip notifier level
net: dsa: introduce a separate cross-chip notifier type for host FDBs
net: dsa: reference count the MDB entries at the cross-chip notifier level
...
Add documentation for the devlink feature prestera switchdev driver supports:
add description for the support of the driver-specific devlink traps
(include both traps with action TRAP and action DROP);
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink rate objects section at devlink port documentation.
Add devlink rate support info at netdevsim devlink documentation.
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation is missing and it's not very clear what
this callback is for - presumably testing the recovery?
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor tweaks and improvement of wording about the diagnose callback.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
