i2c: qcom-cci: Enforce the required CCI clock rate

The CCI hw_params timing values are only valid at the specific clock
rate they were calibrated for. A previous change made the driver select
the timing set matching the currently running clock rate, but the rate
itself was still left to the DT (assigned-clock-rates) or the bootloader,
which is fragile: if no rate is enforced the timings may not match and
violate the I2C specification.

Actively drive the CCI clock to the rate required by the configured
modes. The single CCI clock is shared by all masters, which may run in
different modes, so cci_get_required_rate() picks the lowest rate that
has a valid timing set for every active master's mode. This avoids
clocking the bus faster than necessary while still satisfying every
master (e.g. a Fast+ master forces 37.5 MHz).

Apply the rate through the OPP framework so that boards describing an
opp table also get the required power-domain/regulator votes for that rate.
Boards without an OPP table simply fall back to plain clk_set_rate()
behavior, so existing DTs keep working.

Drop the now-redundant hw_params[].thigh check in cci_get_hw_params(),
cci_get_required_rate() already rejects rates lacking a valid timing
set for an active master's mode.

Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://patch.msgid.link/20260929-cci-clk-fix-v6-5-62a268cccb0f@oss.qualcomm.com

drivers/i2c/busses/Kconfig

@@ -1050,6 +1050,7 @@ config I2C_PXA_SLAVE
 config I2C_QCOM_CCI
 	tristate "Qualcomm Camera Control Interface"
 	depends on ARCH_QCOM || COMPILE_TEST
+	select PM_OPP
 	help
 	  If you say yes to this option, support will be included for the
 	  built-in camera control interface on the Qualcomm SoCs.

drivers/i2c/busses/i2c-qcom-cci.c

@@ -11,6 +11,7 @@
 #include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
+#include <linux/pm_opp.h>
 
 #define CCI_HW_VERSION				0x0
 #define CCI_RESET_CMD				0x004
@@ -318,7 +319,7 @@ static const struct hw_params *cci_get_hw_params(struct cci *cci, int mode)
 	unsigned long rate = clk_get_rate(cci->cci_clk);
 	int ri = cci_clk_rate_idx(rate);
 
-	if (ri >= 0 && mode <= cci->data->max_mode && cci_hw_params[ri][mode].thigh)
+	if (ri >= 0 && mode <= cci->data->max_mode)
 		return &cci_hw_params[ri][mode];
 
 	return NULL;
@@ -575,6 +576,66 @@ static void cci_disable_clocks(struct cci *cci)
 	clk_bulk_disable_unprepare(cci->nclocks, cci->clocks);
 }
 
+/*
+ * The single CCI clock is shared by all masters, which may run in different
+ * modes. Pick the lowest rate that has a valid timing set for every active
+ * master's mode.
+ */
+static int cci_get_required_rate(struct cci *cci, unsigned long *rate)
+{
+	for (int ri = 0; ri < NUM_CCI_CLK_RATES; ri++) {
+		bool supported = true;
+
+		for (int i = 0; i < cci->data->num_masters; i++) {
+			int mode = cci->master[i].mode;
+
+			if (!cci->master[i].cci)
+				continue;
+
+			if (mode > cci->data->max_mode ||
+			    !cci_hw_params[ri][mode].thigh) {
+				supported = false;
+				break;
+			}
+		}
+
+		if (supported) {
+			*rate = cci_clk_rates[ri];
+			return 0;
+		}
+	}
+
+	return -EOPNOTSUPP;
+}
+
+static int cci_set_core_rate(struct cci *cci)
+{
+	struct device *dev = cci->dev;
+	unsigned long rate;
+	int ret;
+
+	ret = cci_get_required_rate(cci, &rate);
+	if (ret) {
+		dev_err(dev, "no CCI clock rate satisfies all masters\n");
+		return ret;
+	}
+
+	ret = dev_pm_opp_set_rate(dev, rate);
+	if (ret) {
+		dev_err(dev, "CCI clock could not be set to %lu Hz\n", rate);
+		return ret;
+	}
+
+	/*
+	 * Sanity: The hw_params timings are only valid at the exact
+	 * expected rate, verify what landed on the hardware.
+	 */
+	if (clk_get_rate(cci->cci_clk) != rate)
+		dev_warn(dev, "CCI clock is not at expected %lu Hz\n", rate);
+
+	return 0;
+}
+
 static int __maybe_unused cci_suspend_runtime(struct device *dev)
 {
 	struct cci *cci = dev_get_drvdata(dev);
@@ -678,6 +739,19 @@ static int cci_probe(struct platform_device *pdev)
 		return dev_err_probe(dev, PTR_ERR(cci->cci_clk),
 				     "failed to get CCI clock\n");
 
+	ret = devm_pm_opp_set_clkname(dev, "cci");
+	if (ret)
+		return dev_err_probe(dev, ret, "failed to set CCI OPP clk\n");
+
+	/* OPP table is optional */
+	ret = devm_pm_opp_of_add_table(dev);
+	if (ret && ret != -ENODEV)
+		return dev_err_probe(dev, ret, "failed to add OPP table\n");
+
+	ret = cci_set_core_rate(cci);
+	if (ret)
+		return ret;
+
 	ret = cci_enable_clocks(cci);
 	if (ret < 0)
 		return ret;