spi: dt-bindings: Convert Freescale SPI bindings to YAML

fsl-spi.txt contains the bindings for the fsl,spi and fsl,espi
contollers. Convert them to YAML.

Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Link: https://patch.msgid.link/20250220-ppcyaml-spi-v3-1-e340613c7875@posteo.net
Signed-off-by: Mark Brown <broonie@kernel.org>

Documentation/devicetree/bindings/spi/fsl,espi.yaml

@@ -0,0 +1,65 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/fsl,espi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale eSPI (Enhanced Serial Peripheral Interface) controller
+
+maintainers:
+  - J. Neuschäfer <j.ne@posteo.net>
+
+properties:
+  compatible:
+    const: fsl,mpc8536-espi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  fsl,espi-num-chipselects:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 1, 4 ]
+    description: The number of the chipselect signals.
+
+  fsl,csbef:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 15
+    description: Chip select assertion time in bits before frame starts
+
+  fsl,csaft:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 15
+    description: Chip select negation time in bits after frame ends
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - fsl,espi-num-chipselects
+
+allOf:
+  - $ref: spi-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    spi@110000 {
+        compatible = "fsl,mpc8536-espi";
+        reg = <0x110000 0x1000>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+        interrupts = <53 IRQ_TYPE_EDGE_FALLING>;
+        fsl,espi-num-chipselects = <4>;
+        fsl,csbef = <1>;
+        fsl,csaft = <1>;
+    };
+
+...

Documentation/devicetree/bindings/spi/fsl,spi.yaml

@@ -0,0 +1,74 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/fsl,spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale SPI (Serial Peripheral Interface) controller
+
+maintainers:
+  - J. Neuschäfer <j.ne@posteo.net>
+
+properties:
+  compatible:
+    enum:
+      - fsl,spi
+      - aeroflexgaisler,spictrl
+
+  reg:
+    maxItems: 1
+
+  cell-index:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: |
+      QE SPI subblock index.
+      0: QE subblock SPI1
+      1: QE subblock SPI2
+
+  mode:
+    description: SPI operation mode
+    enum:
+      - cpu
+      - cpu-qe
+
+  interrupts:
+    maxItems: 1
+
+  clock-frequency:
+    description: input clock frequency to non FSL_SOC cores
+
+  cs-gpios: true
+
+  fsl,spisel_boot:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      For the MPC8306 and MPC8309, specifies that the SPISEL_BOOT signal is used
+      as chip select for a slave device. Use reg = <number of gpios> in the
+      corresponding child node, i.e. 0 if the cs-gpios property is not present.
+
+required:
+  - compatible
+  - reg
+  - mode
+  - interrupts
+
+allOf:
+  - $ref: spi-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    spi@4c0 {
+        compatible = "fsl,spi";
+        reg = <0x4c0 0x40>;
+        cell-index = <0>;
+        interrupts = <82 0>;
+        mode = "cpu";
+        cs-gpios = <&gpio 18 IRQ_TYPE_EDGE_RISING          // device reg=<0>
+                    &gpio 19 IRQ_TYPE_EDGE_RISING>;        // device reg=<1>
+    };
+
+...

Documentation/devicetree/bindings/spi/fsl-spi.txt

@@ -1,62 +0,0 @@
-* SPI (Serial Peripheral Interface)
-
-Required properties:
-- cell-index : QE SPI subblock index.
-		0: QE subblock SPI1
-		1: QE subblock SPI2
-- compatible : should be "fsl,spi" or "aeroflexgaisler,spictrl".
-- mode : the SPI operation mode, it can be "cpu" or "cpu-qe".
-- reg : Offset and length of the register set for the device
-- interrupts : <a b> where a is the interrupt number and b is a
-  field that represents an encoding of the sense and level
-  information for the interrupt.  This should be encoded based on
-  the information in section 2) depending on the type of interrupt
-  controller you have.
-- clock-frequency : input clock frequency to non FSL_SOC cores
-
-Optional properties:
-- cs-gpios : specifies the gpio pins to be used for chipselects.
-  The gpios will be referred to as reg = <index> in the SPI child nodes.
-  If unspecified, a single SPI device without a chip select can be used.
-- fsl,spisel_boot : for the MPC8306 and MPC8309, specifies that the
-  SPISEL_BOOT signal is used as chip select for a slave device. Use
-  reg = <number of gpios> in the corresponding child node, i.e. 0 if
-  the cs-gpios property is not present.
-
-Example:
-	spi@4c0 {
-		cell-index = <0>;
-		compatible = "fsl,spi";
-		reg = <4c0 40>;
-		interrupts = <82 0>;
-		interrupt-parent = <700>;
-		mode = "cpu";
-		cs-gpios = <&gpio 18 1		// device reg=<0>
-			    &gpio 19 1>;	// device reg=<1>
-	};
-
-
-* eSPI (Enhanced Serial Peripheral Interface)
-
-Required properties:
-- compatible : should be "fsl,mpc8536-espi".
-- reg : Offset and length of the register set for the device.
-- interrupts : should contain eSPI interrupt, the device has one interrupt.
-- fsl,espi-num-chipselects : the number of the chipselect signals.
-
-Optional properties:
-- fsl,csbef: chip select assertion time in bits before frame starts
-- fsl,csaft: chip select negation time in bits after frame ends
-
-Example:
-	spi@110000 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "fsl,mpc8536-espi";
-		reg = <0x110000 0x1000>;
-		interrupts = <53 0x2>;
-		interrupt-parent = <&mpic>;
-		fsl,espi-num-chipselects = <4>;
-		fsl,csbef = <1>;
-		fsl,csaft = <1>;
-	};