From 0863e01c39930cbefb25b4b111065a9089f46de0 Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Thu, 30 Aug 2018 10:14:58 +0200 Subject: [PATCH 1/8] arm64: dts: marvell: move AP806/CP110 thermal nodes into a new syscon New bindings impose to declare the thermal IP from within a new syscon. Signed-off-by: Miquel Raynal Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-ap806.dtsi | 14 ++++++++++---- arch/arm64/boot/dts/marvell/armada-cp110.dtsi | 18 ++++++++++++------ 2 files changed, 22 insertions(+), 10 deletions(-) diff --git a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi index 176e38d54872..27930394249d 100644 --- a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi @@ -247,10 +247,16 @@ ap_gpio: gpio@1040 { }; }; - ap_thermal: thermal@6f808c { - compatible = "marvell,armada-ap806-thermal"; - reg = <0x6f808c 0x4>, - <0x6f8084 0x8>; + ap_syscon1: system-controller@6f8000 { + compatible = "syscon", "simple-mfd"; + reg = <0x6f8000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + ap_thermal: thermal-sensor@80 { + compatible = "marvell,armada-ap806-thermal"; + reg = <0x80 0x10>; + }; }; }; }; diff --git a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi index 840c8454d03e..70a784de3e06 100644 --- a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi @@ -162,12 +162,6 @@ CP110_LABEL(rtc): rtc@284000 { interrupts = ; }; - CP110_LABEL(thermal): thermal@400078 { - compatible = "marvell,armada-cp110-thermal"; - reg = <0x400078 0x4>, - <0x400070 0x8>; - }; - CP110_LABEL(syscon0): system-controller@440000 { compatible = "syscon", "simple-mfd"; reg = <0x440000 0x2000>; @@ -208,6 +202,18 @@ CP110_LABEL(gpio2): gpio@140 { }; }; + CP110_LABEL(syscon1): system-controller@400000 { + compatible = "syscon", "simple-mfd"; + reg = <0x400000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + CP110_LABEL(thermal): thermal-sensor@70 { + compatible = "marvell,armada-cp110-thermal"; + reg = <0x70 0x10>; + }; + }; + CP110_LABEL(usb3_0): usb3@500000 { compatible = "marvell,armada-8k-xhci", "generic-xhci"; From 3be148512ebcb8efbaa48b90b3ec2e9376945eb9 Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Thu, 30 Aug 2018 10:14:59 +0200 Subject: [PATCH 2/8] arm64: dts: marvell: add thermal-zone node in ap806 DTSI file Add a thermal-zone node and fill in all the sensors available in an ap806 (one in the IC plus one per CPU). Signed-off-by: Miquel Raynal Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-ap806.dtsi | 60 +++++++++++++++++++ 1 file changed, 60 insertions(+) diff --git a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi index 27930394249d..9a5abad72b66 100644 --- a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi @@ -6,6 +6,7 @@ */ #include +#include /dts-v1/; @@ -256,8 +257,67 @@ ap_syscon1: system-controller@6f8000 { ap_thermal: thermal-sensor@80 { compatible = "marvell,armada-ap806-thermal"; reg = <0x80 0x10>; + #thermal-sensor-cells = <1>; }; }; }; }; + + /* + * The thermal IP features one internal sensor plus, if applicable, one + * remote channel wired to one sensor per CPU. + * + * The cooling maps are always empty as there are no cooling devices. + */ + thermal-zones { + ap_thermal_ic: ap-thermal-ic { + polling-delay-passive = <1000>; + polling-delay = <1000>; + + thermal-sensors = <&ap_thermal 0>; + + trips { }; + cooling-maps { }; + }; + + ap_thermal_cpu1: ap-thermal-cpu1 { + polling-delay-passive = <1000>; + polling-delay = <1000>; + + thermal-sensors = <&ap_thermal 1>; + + trips { }; + cooling-maps { }; + }; + + ap_thermal_cpu2: ap-thermal-cpu2 { + polling-delay-passive = <1000>; + polling-delay = <1000>; + + thermal-sensors = <&ap_thermal 2>; + + trips { }; + cooling-maps { }; + }; + + ap_thermal_cpu3: ap-thermal-cpu3 { + polling-delay-passive = <1000>; + polling-delay = <1000>; + + thermal-sensors = <&ap_thermal 3>; + + trips { }; + cooling-maps { }; + }; + + ap_thermal_cpu4: ap-thermal-cpu4 { + polling-delay-passive = <1000>; + polling-delay = <1000>; + + thermal-sensors = <&ap_thermal 4>; + + trips { }; + cooling-maps { }; + }; + }; }; From a60bdfc0c1ca82e4c30c03ff58e995e67f0f233b Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Thu, 30 Aug 2018 10:15:00 +0200 Subject: [PATCH 3/8] arm64: dts: marvell: add macro to make distinction between node names Because the label is different between CPs, the full path of a node is unique. However, when referring to the end of the path only (the node name), this name is not unique anymore. The *thermal_zone_of_sensor_register() functions of the thermal core present this limitation and prevent having a thermal-zone per CP. Add a macro to make the distinction between node names to solve this situation. Signed-off-by: Miquel Raynal Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-common.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/marvell/armada-common.dtsi b/arch/arm64/boot/dts/marvell/armada-common.dtsi index d5e8aedec188..b29c6405d214 100644 --- a/arch/arm64/boot/dts/marvell/armada-common.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-common.dtsi @@ -7,4 +7,5 @@ #define PASTER(x, y) x ## y #define EVALUATOR(x, y) PASTER(x, y) #define CP110_LABEL(name) EVALUATOR(CP110_NAME, EVALUATOR(_, name)) +#define CP110_NODE_NAME(name) EVALUATOR(CP110_NAME, EVALUATOR(-, name)) #define ADDRESSIFY(addr) EVALUATOR(0x, addr) From f656c801575626b43b8482e900fe81963fa844f2 Mon Sep 17 00:00:00 2001 From: Miquel Raynal Date: Thu, 30 Aug 2018 10:15:01 +0200 Subject: [PATCH 4/8] arm64: dts: marvell: add thermal-zone node in cp110 DTSI file Add a thermal-zone node and fill in all the sensors available in a cp110 (only one in the thermal IP). Signed-off-by: Miquel Raynal Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-cp110.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi index 70a784de3e06..df3f85c3ff35 100644 --- a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi @@ -6,6 +6,7 @@ */ #include +#include #include "armada-common.dtsi" @@ -19,6 +20,23 @@ / { * save one indentation level */ CP110_NAME: CP110_NAME { }; + + /* + * CPs only have one sensor in the thermal IC. + * + * The cooling maps are empty as there are no cooling devices. + */ + thermal-zones { + CP110_LABEL(thermal_ic): CP110_NODE_NAME(thermal-ic) { + polling-delay-passive = <1000>; + polling-delay = <1000>; + + thermal-sensors = <&CP110_LABEL(thermal) 0>; + + trips { }; + cooling-maps { }; + }; + }; }; &CP110_NAME { @@ -211,6 +229,7 @@ CP110_LABEL(syscon1): system-controller@400000 { CP110_LABEL(thermal): thermal-sensor@70 { compatible = "marvell,armada-cp110-thermal"; reg = <0x70 0x10>; + #thermal-sensor-cells = <1>; }; }; From a6120833272c03693c6e027f3a0313c7ca8100ae Mon Sep 17 00:00:00 2001 From: Baruch Siach Date: Sat, 22 Sep 2018 21:59:43 +0300 Subject: [PATCH 5/8] arm64: dts: add support for SolidRun Clearfog GT 8K The SolidRun Clearfog GT-8K is based on Marvell Armada 8040 SoC. https://wiki.solid-run.com/doku.php?id=products:a8040:clearfoggt8k The following devices were tested with this DT on top of kernel v4.19-rc4: * 1GB Ethernet WAN * 4 ports 1GB Ethernet switch (2.5GB uplink) * SFP port * SATA on CON3 PCIe slot * USB3 type A port * SD card and eMMC * 2 LEDs * 2 push buttons [gregory: fix block comment alignement] Signed-off-by: Baruch Siach Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/Makefile | 1 + .../marvell/armada-8040-clearfog-gt-8k.dts | 434 ++++++++++++++++++ 2 files changed, 435 insertions(+) create mode 100644 arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile index ea9d49f2a911..eca8bac6303a 100644 --- a/arch/arm64/boot/dts/marvell/Makefile +++ b/arch/arm64/boot/dts/marvell/Makefile @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb +dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-clearfog-gt-8k.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts new file mode 100644 index 000000000000..1db44b0ec030 --- /dev/null +++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts @@ -0,0 +1,434 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2018 SolidRun ltd. + * Based on Marvell MACCHIATOBin board + * + * Device Tree file for SolidRun's ClearFog GT 8K + */ + +#include "armada-8040.dtsi" + +#include +#include + +/ { + model = "SolidRun ClearFog GT 8K"; + compatible = "solidrun,clearfog-gt-8k", "marvell,armada8040", + "marvell,armada-ap806-quad", "marvell,armada-ap806"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@00000000 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + aliases { + ethernet0 = &cp1_eth1; + ethernet1 = &cp0_eth0; + ethernet2 = &cp1_eth2; + }; + + v_3_3: regulator-3-3v { + compatible = "regulator-fixed"; + regulator-name = "v_3_3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + status = "okay"; + }; + + v_5v0_usb3_hst_vbus: regulator-usb3-vbus0 { + compatible = "regulator-fixed"; + gpio = <&cp0_gpio2 15 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_xhci_vbus_pins>; + regulator-name = "v_5v0_usb3_hst_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + status = "okay"; + }; + + usb3h0_phy: usb3_phy0 { + compatible = "usb-nop-xceiv"; + vcc-supply = <&v_5v0_usb3_hst_vbus>; + }; + + sfp_cp0_eth0: sfp-cp0-eth0 { + compatible = "sff,sfp"; + i2c-bus = <&cp0_i2c1>; + mod-def0-gpio = <&cp0_gpio2 17 GPIO_ACTIVE_LOW>; + tx-disable-gpio = <&cp1_gpio1 29 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_sfp_present_pins &cp1_sfp_tx_disable_pins>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&cp0_led0_pins + &cp0_led1_pins>; + pinctrl-names = "default"; + /* No designated function for these LEDs at the moment */ + led0 { + label = "clearfog-gt-8k:green:led0"; + gpios = <&cp0_gpio2 8 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + led1 { + label = "clearfog-gt-8k:green:led1"; + gpios = <&cp0_gpio2 9 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&cp0_gpio_reset_pins &cp1_wps_button_pins>; + pinctrl-names = "default"; + + button_0 { + /* The rear button */ + label = "Rear Button"; + gpios = <&cp0_gpio2 7 GPIO_ACTIVE_LOW>; + linux,can-disable; + linux,code = ; + }; + + button_1 { + /* The wps button */ + label = "WPS Button"; + gpios = <&cp1_gpio1 30 GPIO_ACTIVE_LOW>; + linux,can-disable; + linux,code = ; + }; + }; +}; + +&uart0 { + status = "okay"; + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; +}; + +&ap_sdhci0 { + bus-width = <8>; + no-1-8-v; + no-sd; + no-sdio; + non-removable; + status = "okay"; + vqmmc-supply = <&v_3_3>; +}; + +&cp0_i2c0 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c0_pins>; + status = "okay"; +}; + +&cp0_i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c1_pins>; + status = "okay"; +}; + +&cp0_pinctrl { + /* + * MPP Bus: + * [0-31] = 0xff: Keep default CP0_shared_pins: + * [11] CLKOUT_MPP_11 (out) + * [23] LINK_RD_IN_CP2CP (in) + * [25] CLKOUT_MPP_25 (out) + * [29] AVS_FB_IN_CP2CP (in) + * [32, 33, 34] pci0/1/2 reset + * [35-38] CP0 I2C1 and I2C0 + * [39] GPIO reset button + * [40,41] LED0 and LED1 + * [43] 1512 phy reset + * [47] USB VBUS EN (active low) + * [48] FAN PWM + * [49] SFP+ present signal + * [50] TPM interrupt + * [51] WLAN0 disable + * [52] WLAN1 disable + * [53] LTE disable + * [54] NFC reset + * [55] Micro SD card detect + * [56-61] Micro SD + */ + + cp0_pci0_reset_pins: pci0-reset-pins { + marvell,pins = "mpp32"; + marvell,function = "gpio"; + }; + + cp0_pci1_reset_pins: pci1-reset-pins { + marvell,pins = "mpp33"; + marvell,function = "gpio"; + }; + + cp0_pci2_reset_pins: pci2-reset-pins { + marvell,pins = "mpp34"; + marvell,function = "gpio"; + }; + + cp0_i2c1_pins: i2c1-pins { + marvell,pins = "mpp35", "mpp36"; + marvell,function = "i2c1"; + }; + + cp0_i2c0_pins: i2c0-pins { + marvell,pins = "mpp37", "mpp38"; + marvell,function = "i2c0"; + }; + + cp0_gpio_reset_pins: gpio-reset-pins { + marvell,pins = "mpp39"; + marvell,function = "gpio"; + }; + + cp0_led0_pins: led0-pins { + marvell,pins = "mpp40"; + marvell,function = "gpio"; + }; + + cp0_led1_pins: led1-pins { + marvell,pins = "mpp41"; + marvell,function = "gpio"; + }; + + cp0_copper_eth_phy_reset: copper-eth-phy-reset { + marvell,pins = "mpp43"; + marvell,function = "gpio"; + }; + + cp0_xhci_vbus_pins: xhci0-vbus-pins { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + + cp0_fan_pwm_pins: fan-pwm-pins { + marvell,pins = "mpp48"; + marvell,function = "gpio"; + }; + + cp0_sfp_present_pins: sfp-present-pins { + marvell,pins = "mpp49"; + marvell,function = "gpio"; + }; + + cp0_tpm_irq_pins: tpm-irq-pins { + marvell,pins = "mpp50"; + marvell,function = "gpio"; + }; + + cp0_sdhci_pins: sdhci-pins { + marvell,pins = "mpp55", "mpp56", "mpp57", "mpp58", "mpp59", + "mpp60", "mpp61"; + marvell,function = "sdio"; + }; +}; + +&cp0_gpio2 { + sata_reset { + gpio-hog; + gpios = <1 GPIO_ACTIVE_HIGH>; + output-high; + }; +}; + +&cp0_ethernet { + status = "okay"; +}; + +/* SFP */ +&cp0_eth0 { + status = "okay"; + phy-mode = "10gbase-kr"; + managed = "in-band-status"; + phys = <&cp0_comphy2 0>; + sfp = <&sfp_cp0_eth0>; +}; + +&cp0_sdhci0 { + broken-cd; + bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_sdhci_pins>; + status = "okay"; + vqmmc-supply = <&v_3_3>; +}; + +&cp1_pinctrl { + /* + * MPP Bus: + * [0-5] TDM + * [6] VHV Enable + * [7] CP1 SPI0 CSn1 (FXS) + * [8] CP1 SPI0 CSn0 (TPM) + * [9.11]CP1 SPI0 MOSI/MISO/CLK + * [13] CP1 SPI1 MISO (TDM and SPI ROM shared) + * [14] CP1 SPI1 CS0n (64Mb SPI ROM) + * [15] CP1 SPI1 MOSI (TDM and SPI ROM shared) + * [16] CP1 SPI1 CLK (TDM and SPI ROM shared) + * [24] Topaz switch reset + * [26] Buzzer + * [27] CP1 SMI MDIO + * [28] CP1 SMI MDC + * [29] CP0 10G SFP TX Disable + * [30] WPS button + * [31] Front panel button + */ + + cp1_spi1_pins: spi1-pins { + marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; + marvell,function = "spi1"; + }; + + cp1_switch_reset_pins: switch-reset-pins { + marvell,pins = "mpp24"; + marvell,function = "gpio"; + }; + + cp1_ge_mdio_pins: ge-mdio-pins { + marvell,pins = "mpp27", "mpp28"; + marvell,function = "ge"; + }; + + cp1_sfp_tx_disable_pins: sfp-tx-disable-pins { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + + cp1_wps_button_pins: wps-button-pins { + marvell,pins = "mpp30"; + marvell,function = "gpio"; + }; +}; + +&cp1_sata0 { + pinctrl-0 = <&cp0_pci1_reset_pins>; + status = "okay"; +}; + +&cp1_mdio { + pinctrl-names = "default"; + pinctrl-0 = <&cp1_ge_mdio_pins>; + status = "okay"; + + ge_phy: ethernet-phy@0 { + /* LED0 - GB link + * LED1 - on: link, blink: activity + */ + marvell,reg-init = <3 16 0 0x1017>; + reg = <0>; + }; + + switch0: switch0@4 { + compatible = "marvell,mv88e6085"; + reg = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&cp1_switch_reset_pins>; + reset-gpios = <&cp1_gpio1 24 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + label = "lan2"; + phy-handle = <&switch0phy0>; + }; + + port@2 { + reg = <2>; + label = "lan1"; + phy-handle = <&switch0phy1>; + }; + + port@3 { + reg = <3>; + label = "lan4"; + phy-handle = <&switch0phy2>; + }; + + port@4 { + reg = <4>; + label = "lan3"; + phy-handle = <&switch0phy3>; + }; + + port@5 { + reg = <5>; + label = "cpu"; + ethernet = <&cp1_eth2>; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch0phy0: switch0phy0@11 { + reg = <0x11>; + }; + + switch0phy1: switch0phy1@12 { + reg = <0x12>; + }; + + switch0phy2: switch0phy2@13 { + reg = <0x13>; + }; + + switch0phy3: switch0phy3@14 { + reg = <0x14>; + }; + }; + }; +}; + +&cp1_ethernet { + status = "okay"; +}; + +/* 1G copper */ +&cp1_eth1 { + status = "okay"; + phy-mode = "sgmii"; + phy = <&ge_phy>; + phys = <&cp1_comphy3 1>; +}; + +/* Switch uplink */ +&cp1_eth2 { + status = "okay"; + phy-mode = "2500base-x"; + phys = <&cp1_comphy5 2>; + fixed-link { + speed = <2500>; + full-duplex; + }; +}; + +&cp1_spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&cp1_spi1_pins>; + status = "okay"; + + spi-flash@0 { + compatible = "st,w25q32"; + spi-max-frequency = <50000000>; + reg = <0>; + }; +}; + +&cp1_usb3_0 { + usb-phy = <&usb3h0_phy>; + status = "okay"; +}; From eeee84f7a6400807e22240e3bd43aac4a01c0471 Mon Sep 17 00:00:00 2001 From: Antoine Tenart Date: Mon, 24 Sep 2018 11:00:01 +0200 Subject: [PATCH 6/8] arm64: dts: marvell: armada-cp110: change the PPv2 IRQ names This patch changes the PPv2 IRQ names in the CP110 device tree to match a corresponding change in the Marvell PPv2 driver. The reason this was updated is the IRQ where names after Tx/Rx interrupts, but this is not true and can be configured. A following patch will add more of them and the names wouldn't make sense. Signed-off-by: Antoine Tenart Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-cp110.dtsi | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi index df3f85c3ff35..9d2a634b0975 100644 --- a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi @@ -71,8 +71,8 @@ CP110_LABEL(eth0): eth0 { , , ; - interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", - "tx-cpu3", "rx-shared", "link"; + interrupt-names = "hif0", "hif1", "hif2", + "hif3", "hif4", "link"; port-id = <0>; gop-port-id = <0>; status = "disabled"; @@ -85,8 +85,8 @@ CP110_LABEL(eth1): eth1 { , , ; - interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", - "tx-cpu3", "rx-shared", "link"; + interrupt-names = "hif0", "hif1", "hif2", + "hif3", "hif4", "link"; port-id = <1>; gop-port-id = <2>; status = "disabled"; @@ -99,8 +99,8 @@ CP110_LABEL(eth2): eth2 { , , ; - interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", - "tx-cpu3", "rx-shared", "link"; + interrupt-names = "hif0", "hif1", "hif2", + "hif3", "hif4", "link"; port-id = <2>; gop-port-id = <3>; status = "disabled"; From dd0da407bb64afda94ce4a068c5f9f43c291e788 Mon Sep 17 00:00:00 2001 From: Antoine Tenart Date: Mon, 24 Sep 2018 11:00:02 +0200 Subject: [PATCH 7/8] arm64: dts: marvell: armada-cp110: describe more PPv2 interrupts This patch describes 3 additional interrupts per PPv2 port. Those interrupts will be used later in future versions of the Marvell PPv2 driver, and now the device tree description matches the hardware capabilities. Signed-off-by: Antoine Tenart Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-cp110.dtsi | 21 ++++++++++++++++--- 1 file changed, 18 insertions(+), 3 deletions(-) diff --git a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi index 9d2a634b0975..f3a630efcf3a 100644 --- a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi @@ -70,9 +70,14 @@ CP110_LABEL(eth0): eth0 { , , , + , + , + , + , ; interrupt-names = "hif0", "hif1", "hif2", - "hif3", "hif4", "link"; + "hif3", "hif4", "hif5", "hif6", "hif7", + "hif8", "link"; port-id = <0>; gop-port-id = <0>; status = "disabled"; @@ -84,9 +89,14 @@ CP110_LABEL(eth1): eth1 { , , , + , + , + , + , ; interrupt-names = "hif0", "hif1", "hif2", - "hif3", "hif4", "link"; + "hif3", "hif4", "hif5", "hif6", "hif7", + "hif8", "link"; port-id = <1>; gop-port-id = <2>; status = "disabled"; @@ -98,9 +108,14 @@ CP110_LABEL(eth2): eth2 { , , , + , + , + , + , ; interrupt-names = "hif0", "hif1", "hif2", - "hif3", "hif4", "link"; + "hif3", "hif4", "hif5", "hif6", "hif7", + "hif8", "link"; port-id = <2>; gop-port-id = <3>; status = "disabled"; From 620cfb31bad4c5be7d9250f1e47a592750fc364b Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Marek=20Beh=C3=BAn?= Date: Mon, 24 Sep 2018 13:06:54 +0200 Subject: [PATCH 8/8] arm64: dts: marvell: armada-37xx: add nodes to support watchdog MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This adds the system controller node for CPU Miscellaneous Registers (which is needed for the watchdog node) and the watchdog node. Signed-off-by: Marek Behún Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi index d9531e242eb4..f5eaec531aa8 100644 --- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi @@ -80,6 +80,19 @@ internal-regs@d0000000 { /* 32M internal register @ 0xd000_0000 */ ranges = <0x0 0x0 0xd0000000 0x2000000>; + wdt: watchdog@8300 { + compatible = "marvell,armada-3700-wdt"; + reg = <0x8300 0x40>; + marvell,system-controller = <&cpu_misc>; + clocks = <&xtalclk>; + }; + + cpu_misc: system-controller@d000 { + compatible = "marvell,armada-3700-cpu-misc", + "syscon"; + reg = <0xd000 0x1000>; + }; + spi0: spi@10600 { compatible = "marvell,armada-3700-spi"; #address-cells = <1>;