diff --git a/Documentation/devicetree/bindings/arm/cpus.yaml b/Documentation/devicetree/bindings/arm/cpus.yaml index 03eb72cb7b30..423f0792b030 100644 --- a/Documentation/devicetree/bindings/arm/cpus.yaml +++ b/Documentation/devicetree/bindings/arm/cpus.yaml @@ -10,9 +10,9 @@ maintainers: - Lorenzo Pieralisi description: |+ - The device tree allows to describe the layout of CPUs in a system through - the "cpus" node, which in turn contains a number of subnodes (ie "cpu") - defining properties for every cpu. + The device tree allows to describe the layout of CPUs in a system through the + "cpus" node, which in turn contains a number of subnodes (ie "cpu") defining + properties for every cpu. Bindings for CPU nodes follow the Devicetree Specification, available from: @@ -41,45 +41,40 @@ description: |+ properties: reg: maxItems: 1 - description: | - Usage and definition depend on ARM architecture version and - configuration: + description: > + Usage and definition depend on ARM architecture version and configuration: - On uniprocessor ARM architectures previous to v7 - this property is required and must be set to 0. + On uniprocessor ARM architectures previous to v7 this property is required + and must be set to 0. - On ARM 11 MPcore based systems this property is - required and matches the CPUID[11:0] register bits. + On ARM 11 MPcore based systems this property is required and matches the + CPUID[11:0] register bits. - Bits [11:0] in the reg cell must be set to - bits [11:0] in CPU ID register. + Bits [11:0] in the reg cell must be set to bits [11:0] in CPU ID register. All other bits in the reg cell must be set to 0. - On 32-bit ARM v7 or later systems this property is - required and matches the CPU MPIDR[23:0] register - bits. + On 32-bit ARM v7 or later systems this property is required and matches + the CPU MPIDR[23:0] register bits. - Bits [23:0] in the reg cell must be set to - bits [23:0] in MPIDR. + Bits [23:0] in the reg cell must be set to bits [23:0] in MPIDR. All other bits in the reg cell must be set to 0. - On ARM v8 64-bit systems this property is required - and matches the MPIDR_EL1 register affinity bits. + On ARM v8 64-bit systems this property is required and matches the + MPIDR_EL1 register affinity bits. * If cpus node's #address-cells property is set to 2 - The first reg cell bits [7:0] must be set to - bits [39:32] of MPIDR_EL1. + The first reg cell bits [7:0] must be set to bits [39:32] of + MPIDR_EL1. - The second reg cell bits [23:0] must be set to - bits [23:0] of MPIDR_EL1. + The second reg cell bits [23:0] must be set to bits [23:0] of + MPIDR_EL1. * If cpus node's #address-cells property is set to 1 - The reg cell bits [23:0] must be set to bits [23:0] - of MPIDR_EL1. + The reg cell bits [23:0] must be set to bits [23:0] of MPIDR_EL1. All other bits in the reg cells must be set to 0. @@ -278,29 +273,26 @@ properties: $ref: /schemas/types.yaml#/definitions/phandle-array items: maxItems: 1 - description: | - List of phandles to idle state nodes supported - by this cpu (see ./idle-states.yaml). + description: + List of phandles to idle state nodes supported by this cpu (see + ./idle-states.yaml). capacity-dmips-mhz: description: u32 value representing CPU capacity (see ../cpu/cpu-capacity.txt) in - DMIPS/MHz, relative to highest capacity-dmips-mhz - in the system. + DMIPS/MHz, relative to highest capacity-dmips-mhz in the system. cci-control-port: true dynamic-power-coefficient: $ref: /schemas/types.yaml#/definitions/uint32 - description: - A u32 value that represents the running time dynamic - power coefficient in units of uW/MHz/V^2. The - coefficient can either be calculated from power + description: > + A u32 value that represents the running time dynamic power coefficient in + units of uW/MHz/V^2. The coefficient can either be calculated from power measurements or derived by analysis. - The dynamic power consumption of the CPU is - proportional to the square of the Voltage (V) and - the clock frequency (f). The coefficient is used to + The dynamic power consumption of the CPU is proportional to the square of + the Voltage (V) and the clock frequency (f). The coefficient is used to calculate the dynamic power as below - Pdyn = dynamic-power-coefficient * V^2 * f @@ -309,10 +301,6 @@ properties: performance-domains: maxItems: 1 - description: - List of phandles and performance domain specifiers, as defined by - bindings of the performance domain provider. See also - dvfs/performance-domain.yaml. power-domains: description: @@ -341,22 +329,21 @@ properties: rockchip,pmu: $ref: /schemas/types.yaml#/definitions/phandle - description: | + description: > Specifies the syscon node controlling the cpu core power domains. - Optional for systems that have an "enable-method" - property value of "rockchip,rk3066-smp" - While optional, it is the preferred way to get access to - the cpu-core power-domains. + Optional for systems that have an "enable-method" property value of + "rockchip,rk3066-smp". While optional, it is the preferred way to get + access to the cpu-core power-domains. secondary-boot-reg: $ref: /schemas/types.yaml#/definitions/uint32 - description: | + description: > Required for systems that have an "enable-method" property value of "brcm,bcm11351-cpu-method", "brcm,bcm23550" or "brcm,bcm-nsp-smp". - This includes the following SoCs: | - BCM11130, BCM11140, BCM11351, BCM28145, BCM28155, BCM21664, BCM23550 + This includes the following SoCs: + BCM11130, BCM11140, BCM11351, BCM28145, BCM28155, BCM21664, BCM23550, BCM58522, BCM58525, BCM58535, BCM58622, BCM58623, BCM58625, BCM88312 The secondary-boot-reg property is a u32 value that specifies the