diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
index 4fbf8d3938ef..0a36ba9e0f5c 100644
--- a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
+++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (c) 2012-2014, 2016-2021 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2021-2022 Qualcomm Innovation Center, Inc. All rights reserved.
  */
 
 #include <linux/gpio/driver.h>
@@ -36,6 +37,8 @@
 #define PMIC_GPIO_SUBTYPE_GPIOC_8CH		0xd
 #define PMIC_GPIO_SUBTYPE_GPIO_LV		0x10
 #define PMIC_GPIO_SUBTYPE_GPIO_MV		0x11
+#define PMIC_GPIO_SUBTYPE_GPIO_LV_VIN2		0x12
+#define PMIC_GPIO_SUBTYPE_GPIO_MV_VIN3		0x13
 
 #define PMIC_MPP_REG_RT_STS			0x10
 #define PMIC_MPP_REG_RT_STS_VAL_MASK		0x1
@@ -522,7 +525,7 @@ static int pmic_gpio_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
 			pad->pullup = arg;
 			break;
 		case PMIC_GPIO_CONF_STRENGTH:
-			if (arg > PMIC_GPIO_STRENGTH_LOW)
+			if (arg > PMIC_GPIO_STRENGTH_HIGH)
 				return -EINVAL;
 			pad->strength = arg;
 			break;
@@ -823,6 +826,16 @@ static int pmic_gpio_populate(struct pmic_gpio_state *state,
 		pad->have_buffer = true;
 		pad->lv_mv_type = true;
 		break;
+	case PMIC_GPIO_SUBTYPE_GPIO_LV_VIN2:
+		pad->num_sources = 2;
+		pad->have_buffer = true;
+		pad->lv_mv_type = true;
+		break;
+	case PMIC_GPIO_SUBTYPE_GPIO_MV_VIN3:
+		pad->num_sources = 3;
+		pad->have_buffer = true;
+		pad->lv_mv_type = true;
+		break;
 	default:
 		dev_err(state->dev, "unknown GPIO type 0x%x\n", subtype);
 		return -ENODEV;
@@ -1149,6 +1162,7 @@ static const struct of_device_id pmic_gpio_of_match[] = {
 	{ .compatible = "qcom,pm6150-gpio", .data = (void *) 10 },
 	{ .compatible = "qcom,pm6150l-gpio", .data = (void *) 12 },
 	{ .compatible = "qcom,pm6350-gpio", .data = (void *) 9 },
+	{ .compatible = "qcom,pm7250b-gpio", .data = (void *) 12 },
 	{ .compatible = "qcom,pm7325-gpio", .data = (void *) 10 },
 	{ .compatible = "qcom,pm8005-gpio", .data = (void *) 4 },
 	{ .compatible = "qcom,pm8008-gpio", .data = (void *) 2 },
@@ -1183,6 +1197,13 @@ static const struct of_device_id pmic_gpio_of_match[] = {
 	{ .compatible = "qcom,pms405-gpio", .data = (void *) 12 },
 	/* pmx55 has 11 GPIOs with holes on 3, 7, 10, 11 */
 	{ .compatible = "qcom,pmx55-gpio", .data = (void *) 11 },
+	{ .compatible = "qcom,pmx65-gpio", .data = (void *) 16 },
+	{ .compatible = "qcom,pm8550-gpio", .data = (void *) 12 },
+	{ .compatible = "qcom,pm8550b-gpio", .data = (void *) 12 },
+	{ .compatible = "qcom,pm8550ve-gpio", .data = (void *) 8 },
+	{ .compatible = "qcom,pm8550vs-gpio", .data = (void *) 6 },
+	{ .compatible = "qcom,pmk8550-gpio", .data = (void *) 6 },
+	{ .compatible = "qcom,pmr735d-gpio", .data = (void *) 2 },
 	{ },
 };
 
diff --git a/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c b/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c
index 1b41adda8129..0f96d130813b 100644
--- a/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c
+++ b/drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (c) 2015, Sony Mobile Communications AB.
- * Copyright (c) 2013, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2013, 2018 The Linux Foundation. All rights reserved.
  */
 
 #include <linux/module.h>
@@ -371,7 +371,7 @@ static int pm8xxx_pin_config_set(struct pinctrl_dev *pctldev,
 			banks |= BIT(0);
 			break;
 		case PM8XXX_QCOM_DRIVE_STRENGH:
-			if (arg > PMIC_GPIO_STRENGTH_LOW) {
+			if (arg > PM8921_GPIO_STRENGTH_LOW) {
 				dev_err(pctrl->dev, "invalid drive strength\n");
 				return -EINVAL;
 			}
diff --git a/include/dt-bindings/pinctrl/qcom,pmic-gpio.h b/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
index e5df5ce45a0f..950be952ad3e 100644
--- a/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
+++ b/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
@@ -12,9 +12,14 @@
 #define PMIC_GPIO_PULL_UP_1P5_30	3
 
 #define PMIC_GPIO_STRENGTH_NO		0
-#define PMIC_GPIO_STRENGTH_HIGH		1
+#define PMIC_GPIO_STRENGTH_LOW		1
 #define PMIC_GPIO_STRENGTH_MED		2
-#define PMIC_GPIO_STRENGTH_LOW		3
+#define PMIC_GPIO_STRENGTH_HIGH		3
+
+#define PM8921_GPIO_STRENGTH_NO		0
+#define PM8921_GPIO_STRENGTH_HIGH	1
+#define PM8921_GPIO_STRENGTH_MED	2
+#define PM8921_GPIO_STRENGTH_LOW	3
 
 /*
  * Note: PM8018 GPIO3 and GPIO4 are supporting