From 30bd02bd634f4a483e965fb41a076e47ea9681ef Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Thu, 16 Jan 2020 23:11:46 +0000 Subject: [PATCH 01/46] arm64: dts: sun50i: H6: Add SPI controllers nodes and pinmuxes The Allwinner H6 SoC contains two SPI controllers similar to the H3/A64, but with the added capability of 3-wire and 4-wire operation modes. For now the driver does not support those, but the SPI registers are fully backwards-compatible, just adding bits and registers which were formerly reserved. So we can use the existing driver in "legacy" SPI modes, for instance to access the SPI NOR flash soldered on the PineH64 board. We use an H6 specific compatible string in addition to the existing H3 string, so when the driver later gains QSPI support, it should work automatically without any DT changes. Tested by accessing the SPI flash on a Pine H64 board (SPI0), also connecting another SPI flash to the SPI1 header pins. Signed-off-by: Andre Przywara Signed-off-by: Maxime Ripard --- arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 55 ++++++++++++++++++++ 1 file changed, 55 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi index 3329283e38ab..41b58ffa8596 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi @@ -338,6 +338,31 @@ mmc2_pins: mmc2-pins { bias-pull-up; }; + /omit-if-no-ref/ + spi0_pins: spi0-pins { + pins = "PC0", "PC2", "PC3"; + function = "spi0"; + }; + + /* pin shared with MMC2-CMD (eMMC) */ + /omit-if-no-ref/ + spi0_cs_pin: spi0-cs-pin { + pins = "PC5"; + function = "spi0"; + }; + + /omit-if-no-ref/ + spi1_pins: spi1-pins { + pins = "PH4", "PH5", "PH6"; + function = "spi1"; + }; + + /omit-if-no-ref/ + spi1_cs_pin: spi1-cs-pin { + pins = "PH3"; + function = "spi1"; + }; + spdif_tx_pin: spdif-tx-pin { pins = "PH7"; function = "spdif"; @@ -504,6 +529,36 @@ i2c2: i2c@5002800 { #size-cells = <0>; }; + spi0: spi@5010000 { + compatible = "allwinner,sun50i-h6-spi", + "allwinner,sun8i-h3-spi"; + reg = <0x05010000 0x1000>; + interrupts = ; + clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>; + clock-names = "ahb", "mod"; + dmas = <&dma 22>, <&dma 22>; + dma-names = "rx", "tx"; + resets = <&ccu RST_BUS_SPI0>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + spi1: spi@5011000 { + compatible = "allwinner,sun50i-h6-spi", + "allwinner,sun8i-h3-spi"; + reg = <0x05011000 0x1000>; + interrupts = ; + clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>; + clock-names = "ahb", "mod"; + dmas = <&dma 23>, <&dma 23>; + dma-names = "rx", "tx"; + resets = <&ccu RST_BUS_SPI1>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + emac: ethernet@5020000 { compatible = "allwinner,sun50i-h6-emac", "allwinner,sun50i-a64-emac"; From e757bdd01780d0ea3e6774247b735caf2d1a9e92 Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Thu, 16 Jan 2020 23:11:47 +0000 Subject: [PATCH 02/46] arm64: dts: allwinner: h6: Pine H64: Add SPI flash node The Pine H64 board comes with SPI flash soldered on the board, connected to the SPI0 pins (so it can also boot from there). Add the required SPI flash DT node to describe this. Unfortunately the SPI CS0 pin collides with the eMMC CMD pin, so we can't use both eMMC and SPI flash at the same time (the first to claim the pin would win, the other's probe routine would then fail). To avoid losing the more useful eMMC device by chance, mark the SPI device as "disabled" for now. A user or some U-Boot code could fix this up if needed, for instance if no eMMC has been detected (it's socketed). Signed-off-by: Andre Przywara Signed-off-by: Maxime Ripard --- .../boot/dts/allwinner/sun50i-h6-pine-h64.dts | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts index d1c2aa5b3a20..3c9dd0d69754 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts @@ -14,6 +14,7 @@ / { aliases { ethernet0 = &emac; serial0 = &uart0; + spi0 = &spi0; }; chosen { @@ -278,6 +279,24 @@ &r_pio { vcc-pm-supply = <®_aldo1>; }; +/* + * The CS pin is shared with the MMC2 CMD pin, so we cannot have the SPI + * flash and eMMC at the same time, as one of them would fail probing. + * Disable SPI0 in here, to prefer the more useful eMMC. U-Boot can + * fix this up in no eMMC is connected. + */ +&spi0 { + pinctrl-0 = <&spi0_pins>, <&spi0_cs_pin>; + pinctrl-names = "default"; + status = "disabled"; + + flash@0 { + compatible = "winbond,w25q128", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <4000000>; + }; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_ph_pins>; From e2c9e67e44fedcf37b383d3cacc525674bed457f Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Thu, 16 Jan 2020 23:11:48 +0000 Subject: [PATCH 03/46] dt-bindings: spi: sunxi: Document new compatible strings The Allwinner H6 SPI controller has advanced features over the H3 version, but remains compatible with it. Document the usual "specific", "fallback" compatible string pair. Also add the R40 version while at it. Signed-off-by: Andre Przywara Signed-off-by: Maxime Ripard --- .../bindings/spi/allwinner,sun6i-a31-spi.yaml | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-) diff --git a/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml index 0565dc49e449..243a6b1e66ea 100644 --- a/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml +++ b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml @@ -18,9 +18,14 @@ properties: "#size-cells": true compatible: - enum: - - allwinner,sun6i-a31-spi - - allwinner,sun8i-h3-spi + oneOf: + - const: allwinner,sun6i-a31-spi + - const: allwinner,sun8i-h3-spi + - items: + - enum: + - allwinner,sun8i-r40-spi + - allwinner,sun50i-h6-spi + - const: allwinner,sun8i-h3-spi reg: maxItems: 1 From 39b6343d1d4180b83edec31e1d0b36fe1ccfaf77 Mon Sep 17 00:00:00 2001 From: Icenowy Zheng Date: Thu, 16 Jan 2020 11:36:35 +0800 Subject: [PATCH 04/46] dt-bindings: arm: sunxi: add binding for PineTab tablet Add the device tree binding for Pine64's PineTab tablet, which uses Allwinner A64 SoC. Signed-off-by: Icenowy Zheng Reviewed-by: Rob Herring Signed-off-by: Maxime Ripard --- Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml index 327ce6730823..159060b65c5d 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.yaml +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml @@ -636,6 +636,11 @@ properties: - const: pine64,pinebook - const: allwinner,sun50i-a64 + - description: Pine64 PineTab + items: + - const: pine64,pinetab + - const: allwinner,sun50i-a64 + - description: Pine64 SoPine Baseboard items: - const: pine64,sopine-baseboard From 674ef1d0a7b23681699994a892a1ed508c7df122 Mon Sep 17 00:00:00 2001 From: Icenowy Zheng Date: Thu, 16 Jan 2020 11:36:36 +0800 Subject: [PATCH 05/46] arm64: dts: allwinner: a64: add support for PineTab PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside. It includes the following peripherals: USB: - A microUSB Type-B port connected to the OTG-capable USB PHY of Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG functionality on this port. - A USB Type-A port is connected to the internal hub attached to the non-OTG USB PHY of Allwinner A64. - There are reserved pins for an external keyboard connected to the internal hub. Power: - The microUSB port has its Vbus connected to AXP803, mentioned above. - A DC jack (of a strange size, 2.5mm outer diameter) is connected to the ACIN of AXP803. - A Li-Polymer battery is connected to the battery pins of AXP803. Storage: - An tradition Pine64 eMMC slot is on the board, mounted with an eMMC module by factory. - An external microSD slot is hidden under a protect case. Display: - A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC. - A mini HDMI port. Input: - A touch panel attached to a Goodix GT9271 touch controller. - Volume keys connected to the LRADC of the A64 SoC. Camera: - An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC. - A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640. Audio: - A headphone jack is conencted to the SoC's internal codec. - A speaker connected is to the Line Out port of SoC's internal codec, via an amplifier. Misc: - Debug UART is muxed with the headphone jack, with the switch next to the microSD slot. - A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC. - Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the one in Pinebook. This commit adds a basically usable device tree for it, implementing most of the features mentioned above. HDMI is not supported now because bad LCD-HDMI coexistence situation of mainline A64 display driver, the front camera currently lacks a driver and a facility to share the bus with the rear one, and the accelerometer currently lacks a DT binding. Signed-off-by: Icenowy Zheng Signed-off-by: Maxime Ripard --- arch/arm64/boot/dts/allwinner/Makefile | 1 + .../boot/dts/allwinner/sun50i-a64-pinetab.dts | 460 ++++++++++++++++++ 2 files changed, 461 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index cf4f78617c3f..6dad63881cd3 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-lts.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts new file mode 100644 index 000000000000..316e8a443913 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts @@ -0,0 +1,460 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2019 Icenowy Zheng + * + */ + +/dts-v1/; + +#include "sun50i-a64.dtsi" +#include "sun50i-a64-cpu-opp.dtsi" + +#include +#include +#include + +/ { + model = "PineTab"; + compatible = "pine64,pinetab", "allwinner,sun50i-a64"; + + aliases { + serial0 = &uart0; + ethernet0 = &rtl8723cs; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>; + brightness-levels = <0 16 18 20 22 24 26 29 32 35 38 42 46 51 56 62 68 75 83 91 100>; + default-brightness-level = <15>; + enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */ + power-supply = <&vdd_bl>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + i2c-csi { + compatible = "i2c-gpio"; + sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; /* PE13 */ + scl-gpios = <&pio 4 12 GPIO_ACTIVE_HIGH>; /* PE12 */ + i2c-gpio,delay-us = <5>; + #address-cells = <1>; + #size-cells = <0>; + + /* Rear camera */ + ov5640: camera@3c { + compatible = "ovti,ov5640"; + reg = <0x3c>; + pinctrl-names = "default"; + pinctrl-0 = <&csi_mclk_pin>; + clocks = <&ccu CLK_CSI_MCLK>; + clock-names = "xclk"; + + AVDD-supply = <®_dldo3>; + DOVDD-supply = <®_aldo1>; + DVDD-supply = <®_eldo3>; + reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* PE14 */ + powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */ + + port { + ov5640_ep: endpoint { + remote-endpoint = <&csi_ep>; + bus-width = <8>; + hsync-active = <1>; /* Active high */ + vsync-active = <0>; /* Active low */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; + }; + }; + + speaker_amp: audio-amplifier { + compatible = "simple-audio-amplifier"; + enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */ + sound-name-prefix = "Speaker Amp"; + }; + + vdd_bl: regulator@0 { + compatible = "regulator-fixed"; + regulator-name = "bl-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ + enable-active-high; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ + post-power-on-delay-ms = <200>; + }; +}; + +&codec { + status = "okay"; +}; + +&codec_analog { + hpvcc-supply = <®_eldo1>; + status = "okay"; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&cpu1 { + cpu-supply = <®_dcdc2>; +}; + +&cpu2 { + cpu-supply = <®_dcdc2>; +}; + +&cpu3 { + cpu-supply = <®_dcdc2>; +}; + +&csi { + status = "okay"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + csi_ep: endpoint { + remote-endpoint = <&ov5640_ep>; + bus-width = <8>; + hsync-active = <1>; /* Active high */ + vsync-active = <0>; /* Active low */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + }; +}; + +&dai { + status = "okay"; +}; + +&de { + status = "okay"; +}; + +&dphy { + status = "okay"; +}; + +&dsi { + vcc-dsi-supply = <®_dldo1>; + status = "okay"; + + panel@0 { + compatible = "feixin,k101-im2ba02"; + reg = <0>; + avdd-supply = <®_dc1sw>; + dvdd-supply = <®_dc1sw>; + cvdd-supply = <®_ldo_io1>; + reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */ + backlight = <&backlight>; + }; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + touchscreen@5d { + compatible = "goodix,gt9271"; + reg = <0x5d>; + interrupt-parent = <&pio>; + interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */ + irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + reset-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */ + AVDD28-supply = <®_ldo_io1>; + }; +}; + +&i2c0_pins { + bias-pull-up; +}; + +&i2c1 { + status = "okay"; + + /* TODO: add Bochs BMA223 accelerometer here */ +}; + +&lradc { + vref-supply = <®_aldo3>; + status = "okay"; + + button-200 { + label = "Volume Up"; + linux,code = ; + channel = <0>; + voltage = <200000>; + }; + + button-400 { + label = "Volume Down"; + linux,code = ; + channel = <0>; + voltage = <400000>; + }; +}; + +&mixer1 { + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + vmmc-supply = <®_dcdc1>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; + disable-wp; + bus-width = <4>; + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <®_dldo4>; + vqmmc-supply = <®_eldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + rtl8723cs: wifi@1 { + reg = <1>; + }; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&pwm { + status = "okay"; +}; + +&r_rsb { + status = "okay"; + + axp803: pmic@3a3 { + compatible = "x-powers,axp803"; + reg = <0x3a3>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + x-powers,drive-vbus-en; + }; +}; + +#include "axp803.dtsi" + +&ac_power_supply { + status = "okay"; +}; + +&battery_power_supply { + status = "okay"; +}; + +®_aldo1 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "dovdd-csi"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pl"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pll-avcc"; +}; + +®_dc1sw { + regulator-name = "vcc-lcd"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd-cpux"; +}; + +/* DCDC3 is polyphased with DCDC2 */ + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-sys"; +}; + +®_dldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-hdmi-dsi-sensor"; +}; + +®_dldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi"; +}; + +®_dldo4 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +®_drivevbus { + regulator-name = "usb0-vbus"; + status = "okay"; +}; + +®_eldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "cpvdd"; +}; + +®_eldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcca-1v8"; +}; + +®_eldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dvdd-1v8-csi"; +}; + +®_fldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-1v2-hsic"; +}; + +®_fldo2 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_ldo_io0 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-usb"; + status = "okay"; +}; + +®_ldo_io1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <3500000>; + regulator-name = "vcc-touchscreen"; + status = "okay"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; +}; + +&sound { + status = "okay"; + simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>; + simple-audio-card,widgets = "Microphone", "Internal Microphone Left", + "Microphone", "Internal Microphone Right", + "Headphone", "Headphone Jack", + "Speaker", "Internal Speaker"; + simple-audio-card,routing = + "Left DAC", "AIF1 Slot 0 Left", + "Right DAC", "AIF1 Slot 0 Right", + "Speaker Amp INL", "LINEOUT", + "Speaker Amp INR", "LINEOUT", + "Internal Speaker", "Speaker Amp OUTL", + "Internal Speaker", "Speaker Amp OUTR", + "Headphone Jack", "HP", + "AIF1 Slot 0 Left ADC", "Left ADC", + "AIF1 Slot 0 Right ADC", "Right ADC", + "Internal Microphone Left", "MBIAS", + "MIC1", "Internal Microphone Left", + "Internal Microphone Right", "HBIAS", + "MIC2", "Internal Microphone Right"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pb_pins>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + +&usbphy { + usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_drivevbus>; + usb1_vbus-supply = <®_ldo_io0>; + status = "okay"; +}; From 787615ad874151af11017e95e29b7f1ef1c1590f Mon Sep 17 00:00:00 2001 From: Samuel Holland Date: Sun, 19 Jan 2020 10:30:56 -0600 Subject: [PATCH 06/46] arm64: dts: allwinner: Enable button wakeup on Orange Pi PC2 The Orange Pi PC2 features a GPIO button. As the button is connected to Port L (pin PL3), it can be used as a wakeup source. Enable this. Signed-off-by: Samuel Holland Signed-off-by: Maxime Ripard --- arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts index 70b5f0998421..c4f89c312f42 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts @@ -61,6 +61,7 @@ sw4 { label = "sw4"; linux,code = ; gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; + wakeup-source; }; }; From 9e556ec5731eb3a7df3ee27e832d74b17390499e Mon Sep 17 00:00:00 2001 From: Samuel Holland Date: Sun, 19 Jan 2020 10:30:57 -0600 Subject: [PATCH 07/46] arm64: dts: allwinner: pinebook: Remove unused vcc3v3 regulator This fixed regulator has no consumers, GPIOs, or other connections. Remove it. Signed-off-by: Samuel Holland Signed-off-by: Maxime Ripard --- arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts | 7 ------- 1 file changed, 7 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts index 3d894b208901..ff32ca1a495e 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -63,13 +63,6 @@ lid_switch { }; }; - reg_vcc3v3: vcc3v3 { - compatible = "regulator-fixed"; - regulator-name = "vcc3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - wifi_pwrseq: wifi_pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ From c0e79b069e4ff6e0881d82ba831424ca7362e828 Mon Sep 17 00:00:00 2001 From: Samuel Holland Date: Sun, 19 Jan 2020 10:30:59 -0600 Subject: [PATCH 08/46] arm64: dts: allwinner: pinebook: Sort device tree nodes The r_i2c node should come before r_rsb, and in any case should not separate the axp803 node from its subnodes. Signed-off-by: Samuel Holland Signed-off-by: Maxime Ripard --- .../boot/dts/allwinner/sun50i-a64-pinebook.dts | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts index ff32ca1a495e..77784f7b1da7 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -172,6 +172,14 @@ &pwm { status = "okay"; }; +/* The ANX6345 eDP-bridge is on r_i2c */ +&r_i2c { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&r_i2c_pl89_pins>; + status = "okay"; +}; + &r_rsb { status = "okay"; @@ -183,14 +191,6 @@ axp803: pmic@3a3 { }; }; -/* The ANX6345 eDP-bridge is on r_i2c */ -&r_i2c { - clock-frequency = <100000>; - pinctrl-names = "default"; - pinctrl-0 = <&r_i2c_pl89_pins>; - status = "okay"; -}; - #include "axp803.dtsi" &ac_power_supply { From c3d22680df8da15c6ee2a6a157fcf3078915cc26 Mon Sep 17 00:00:00 2001 From: Samuel Holland Date: Sun, 19 Jan 2020 10:31:00 -0600 Subject: [PATCH 09/46] arm64: dts: allwinner: pinebook: Make simplefb more consistent Boards generally reference the simplefb nodes from the SoC dtsi by label, not by full path. simplefb_hdmi is already like this in the Pinebook DTS. Update simplefb_lcd to match. Signed-off-by: Samuel Holland Signed-off-by: Maxime Ripard --- .../arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts index 77784f7b1da7..224bed65d008 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -41,12 +41,6 @@ backlight: backlight { chosen { stdout-path = "serial0:115200n8"; - - framebuffer-lcd { - panel-supply = <®_dc1sw>; - dvdd25-supply = <®_dldo2>; - dvdd12-supply = <®_fldo1>; - }; }; gpio_keys { @@ -316,6 +310,12 @@ ®_rtc_ldo { regulator-name = "vcc-rtc"; }; +&simplefb_lcd { + panel-supply = <®_dc1sw>; + dvdd25-supply = <®_dldo2>; + dvdd12-supply = <®_fldo1>; +}; + &simplefb_hdmi { vcc-hdmi-supply = <®_dldo1>; }; From 412e19c34f501da68c19d8fdd7de4c535ea89d3b Mon Sep 17 00:00:00 2001 From: Samuel Holland Date: Sun, 19 Jan 2020 10:31:01 -0600 Subject: [PATCH 10/46] arm64: dts: allwinner: pinebook: Document MMC0 CD pin name Normally GPIO pin references are followed by a comment giving the pin name for searchability. Add the comment here where it was missing. Signed-off-by: Samuel Holland Signed-off-by: Maxime Ripard --- arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts index 224bed65d008..a1e15777d524 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -119,7 +119,7 @@ &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; vmmc-supply = <®_dcdc1>; - cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ disable-wp; bus-width = <4>; status = "okay"; From 9de2b6bf5ecb1f2149ffe19e4aefbdcbe68790f1 Mon Sep 17 00:00:00 2001 From: Samuel Holland Date: Sun, 19 Jan 2020 10:31:02 -0600 Subject: [PATCH 11/46] arm64: dts: allwinner: pinebook: Add GPIO port regulators Allwinner A64 SoC has separate supplies for PC, PD, PE, PG and PL. VCC-PC and VCC-PG are supplied by ELDO1 at 1.8v. VCC-PD is supplied by DCDC1 (VCC-IO) at 3.3v. VCC-PE is supplied by ALDO1, and is unused. VCC-PL creates a circular dependency, so it is omitted for now. Signed-off-by: Samuel Holland Signed-off-by: Maxime Ripard --- .../boot/dts/allwinner/sun50i-a64-pinebook.dts | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts index a1e15777d524..1ec39120323f 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -162,6 +162,13 @@ &ohci1 { status = "okay"; }; +&pio { + vcc-pc-supply = <®_eldo1>; + vcc-pd-supply = <®_dcdc1>; + vcc-pe-supply = <®_aldo1>; + vcc-pg-supply = <®_eldo1>; +}; + &pwm { status = "okay"; }; @@ -174,6 +181,16 @@ &r_i2c { status = "okay"; }; +&r_pio { + /* + * FIXME: We can't add that supply for now since it would + * create a circular dependency between pinctrl, the regulator + * and the RSB Bus. + * + * vcc-pl-supply = <®_aldo2>; + */ +}; + &r_rsb { status = "okay"; From 47ef030c3a796e07fec12c6981bbb46bcb258e2e Mon Sep 17 00:00:00 2001 From: Samuel Holland Date: Sun, 19 Jan 2020 10:31:03 -0600 Subject: [PATCH 12/46] arm64: dts: allwinner: pinebook: Fix backlight regulator The output from the backlight regulator is labeled as "VBKLT" in the schematic. Using the equation and resistor values from the schematic, the output is approximately 18V, not 3.3V. Since the regulator in use (SS6640STR) is a boost regulator powered by PS (battery or AC input), which are both >3.3V, the output could not be 3.3V anyway. Signed-off-by: Samuel Holland Signed-off-by: Maxime Ripard --- .../dts/allwinner/sun50i-a64-pinebook.dts | 20 +++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts index 1ec39120323f..313f4e6edc19 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -21,22 +21,13 @@ aliases { ethernet0 = &rtl8723cs; }; - vdd_bl: regulator@0 { - compatible = "regulator-fixed"; - regulator-name = "bl-3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ - enable-active-high; - }; - backlight: backlight { compatible = "pwm-backlight"; pwms = <&pwm 0 50000 0>; brightness-levels = <0 5 10 15 20 30 40 55 70 85 100>; default-brightness-level = <2>; enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */ - power-supply = <&vdd_bl>; + power-supply = <®_vbklt>; }; chosen { @@ -57,6 +48,15 @@ lid_switch { }; }; + reg_vbklt: vbklt { + compatible = "regulator-fixed"; + regulator-name = "vbklt"; + regulator-min-microvolt = <18000000>; + regulator-max-microvolt = <18000000>; + gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ + enable-active-high; + }; + wifi_pwrseq: wifi_pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ From e95d8d03b5904a373895c14a44eb60264c7bc041 Mon Sep 17 00:00:00 2001 From: Samuel Holland Date: Sun, 19 Jan 2020 10:31:04 -0600 Subject: [PATCH 13/46] arm64: dts: allwinner: pinebook: Fix 5v0 boost regulator Now that AXP803 GPIO support is available, we can properly model the hardware. Replace the use of GPIO0-LDO with a fixed regulator controlled by GPIO0. This boost regulator is used to power the (internal and external) USB ports, as well as the speakers. Signed-off-by: Samuel Holland Signed-off-by: Maxime Ripard --- .../dts/allwinner/sun50i-a64-pinebook.dts | 27 +++++++++---------- 1 file changed, 12 insertions(+), 15 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts index 313f4e6edc19..c06c540e6c08 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -57,6 +57,15 @@ reg_vbklt: vbklt { enable-active-high; }; + reg_vcc5v0: vcc5v0 { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&axp_gpio 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + wifi_pwrseq: wifi_pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ @@ -64,12 +73,7 @@ wifi_pwrseq: wifi_pwrseq { speaker_amp: audio-amplifier { compatible = "simple-audio-amplifier"; - /* - * TODO This is actually a fixed regulator controlled by - * the GPIO line on the PMIC. This should be corrected - * once GPIO support is added for this PMIC. - */ - VCC-supply = <®_ldo_io0>; + VCC-supply = <®_vcc5v0>; enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */ sound-name-prefix = "Speaker Amp"; }; @@ -316,13 +320,6 @@ ®_fldo2 { regulator-name = "vdd-cpus"; }; -®_ldo_io0 { - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-name = "vcc-usb"; - status = "okay"; -}; - ®_rtc_ldo { regulator-name = "vcc-rtc"; }; @@ -371,7 +368,7 @@ &usb_otg { }; &usbphy { - usb0_vbus-supply = <®_ldo_io0>; - usb1_vbus-supply = <®_ldo_io0>; + usb0_vbus-supply = <®_vcc5v0>; + usb1_vbus-supply = <®_vcc5v0>; status = "okay"; }; From 5a5e52161894ab70062e6989aa15f672664334f8 Mon Sep 17 00:00:00 2001 From: Emmanuel Vadot Date: Sat, 18 Jan 2020 16:24:59 +0100 Subject: [PATCH 14/46] arm64: dts: allwinner: a64: Add gpio bank supply for A64-Olinuxino Add the regulators for each bank on this boards. For VCC-PL only add a comment on what regulator is used. We cannot add the property without causing a circular dependency as the PL pins are used to talk to the PMIC. Signed-off-by: Emmanuel Vadot Signed-off-by: Maxime Ripard --- .../boot/dts/allwinner/sun50i-a64-olinuxino.dts | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts index 6dfafa1c879b..5fa9ca0191a8 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts @@ -158,6 +158,17 @@ &r_pio { */ }; +&pio { + vcc-pa-supply = <®_dcdc1>; + vcc-pb-supply = <®_dcdc1>; + vcc-pc-supply = <®_dcdc1>; + vcc-pd-supply = <®_dcdc1>; + vcc-pe-supply = <®_aldo1>; + vcc-pf-supply = <®_dcdc1>; + vcc-pg-supply = <®_dldo4>; + vcc-ph-supply = <®_dcdc1>; +}; + &r_rsb { status = "okay"; @@ -170,6 +181,12 @@ axp803: pmic@3a3 { }; }; +/* VCC-PL is powered by aldo2 but we cannot add it as the RSB */ +/* interface used to talk to the PMIC in on the PL pins */ +/* &r_pio { */ +/* vcc-pl-supply = <®_aldo2>; */ +/* }; */ + #include "axp803.dtsi" &ac_power_supply { From 6a7be15a66e6138d7efad71278177d8432bd4ea5 Mon Sep 17 00:00:00 2001 From: Yangtao Li Date: Mon, 6 Jan 2020 17:46:39 +0000 Subject: [PATCH 15/46] ARM: dts: sun8i-r40: Add thermal sensor and thermal zones There are two sensors, sensor0 for CPU, sensor1 for GPU. Signed-off-by: Yangtao Li Tested-by: Corentin Labbe Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-r40.dtsi | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi index 8f09a24b36ec..d5442b5b6fd2 100644 --- a/arch/arm/boot/dts/sun8i-r40.dtsi +++ b/arch/arm/boot/dts/sun8i-r40.dtsi @@ -47,6 +47,7 @@ #include #include #include +#include / { #address-cells = <1>; @@ -110,6 +111,22 @@ de: display-engine { status = "disabled"; }; + thermal-zones { + cpu_thermal: cpu0-thermal { + /* milliseconds */ + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&ths 0>; + }; + + gpu_thermal: gpu-thermal { + /* milliseconds */ + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&ths 1>; + }; + }; + soc { compatible = "simple-bus"; #address-cells = <1>; @@ -500,6 +517,17 @@ wdt: watchdog@1c20c90 { clocks = <&osc24M>; }; + ths: thermal-sensor@1c24c00 { + compatible = "allwinner,sun8i-r40-ths"; + reg = <0x01c24c00 0x100>; + clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_THS>; + clock-names = "bus", "mod"; + interrupts = ; + resets = <&ccu RST_BUS_THS>; + /* TODO: add nvmem-cells for calibration */ + #thermal-sensor-cells = <1>; + }; + uart0: serial@1c28000 { compatible = "snps,dw-apb-uart"; reg = <0x01c28000 0x400>; From f0df2e05a2d93e5feda871db0401399f5836abaa Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Mon, 10 Feb 2020 18:06:52 +0100 Subject: [PATCH 16/46] dt-bindings: interconnect: sunxi: Add A64 MBUS compatible A64 contains MBUS controller. Add a compatible for it. Acked-by: Rob Herring Signed-off-by: Jernej Skrabec Signed-off-by: Maxime Ripard --- .../devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml b/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml index 9370e64992dd..aa0738b4d534 100644 --- a/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml +++ b/Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.yaml @@ -30,6 +30,7 @@ properties: enum: - allwinner,sun5i-a13-mbus - allwinner,sun8i-h3-mbus + - allwinner,sun50i-a64-mbus reg: maxItems: 1 From fc7c2bfb08c36d26b9cad391636566fcdb75fef0 Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Mon, 10 Feb 2020 18:06:54 +0100 Subject: [PATCH 17/46] arm64: dts: allwinner: a64: Add MBUS controller node A64 contains MBUS, which is the bus used by DMA devices to access system memory. MBUS controller is responsible for arbitration between channels based on set priority and can do some other things as well, like report bandwidth used. It also maps RAM region to different address than CPU. Signed-off-by: Jernej Skrabec Signed-off-by: Maxime Ripard --- arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi index 862b47dc9dc9..251c91724de1 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi @@ -1061,6 +1061,14 @@ pwm: pwm@1c21400 { status = "disabled"; }; + mbus: dram-controller@1c62000 { + compatible = "allwinner,sun50i-a64-mbus"; + reg = <0x01c62000 0x1000>; + clocks = <&ccu 112>; + dma-ranges = <0x00000000 0x40000000 0xc0000000>; + #interconnect-cells = <1>; + }; + csi: csi@1cb0000 { compatible = "allwinner,sun50i-a64-csi"; reg = <0x01cb0000 0x1000>; From a7f3e0bbf2c14abc60fb2e51c26b16fa642bf052 Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Mon, 10 Feb 2020 18:06:55 +0100 Subject: [PATCH 18/46] media: dt-bindings: media: Add Allwinner A64 deinterlace compatible Allwinner A64 SoC also contains deinterlace core, compatible to H3. Add compatible string for it. Acked-by: Rob Herring Signed-off-by: Jernej Skrabec Signed-off-by: Maxime Ripard --- .../bindings/media/allwinner,sun8i-h3-deinterlace.yaml | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/Documentation/devicetree/bindings/media/allwinner,sun8i-h3-deinterlace.yaml b/Documentation/devicetree/bindings/media/allwinner,sun8i-h3-deinterlace.yaml index 2e40f700e84f..8707df613f6c 100644 --- a/Documentation/devicetree/bindings/media/allwinner,sun8i-h3-deinterlace.yaml +++ b/Documentation/devicetree/bindings/media/allwinner,sun8i-h3-deinterlace.yaml @@ -17,7 +17,11 @@ description: |- properties: compatible: - const: allwinner,sun8i-h3-deinterlace + oneOf: + - const: allwinner,sun8i-h3-deinterlace + - items: + - const: allwinner,sun50i-a64-deinterlace + - const: allwinner,sun8i-h3-deinterlace reg: maxItems: 1 From dd00d78d0f41ec1932d90f23741dbf79b8d8544e Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Mon, 10 Feb 2020 18:06:56 +0100 Subject: [PATCH 19/46] arm64: dts: allwinner: a64: Add deinterlace core node A64 contains deinterlace core, compatible to the one found in H3. It can be used in combination with VPU unit to decode and process interlaced videos. Add a node for it. Signed-off-by: Jernej Skrabec Signed-off-by: Maxime Ripard --- arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi index 251c91724de1..72b1b34879c6 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi @@ -1114,6 +1114,20 @@ dphy: d-phy@1ca1000 { #phy-cells = <0>; }; + deinterlace: deinterlace@1e00000 { + compatible = "allwinner,sun50i-a64-deinterlace", + "allwinner,sun8i-h3-deinterlace"; + reg = <0x01e00000 0x20000>; + clocks = <&ccu CLK_BUS_DEINTERLACE>, + <&ccu CLK_DEINTERLACE>, + <&ccu CLK_DRAM_DEINTERLACE>; + clock-names = "bus", "mod", "ram"; + resets = <&ccu RST_BUS_DEINTERLACE>; + interrupts = ; + interconnects = <&mbus 9>; + interconnect-names = "dma-mem"; + }; + hdmi: hdmi@1ee0000 { compatible = "allwinner,sun50i-a64-dw-hdmi", "allwinner,sun8i-a83t-dw-hdmi"; From 221a690420fdad808eb0b39eebb19d4eda95568c Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Mon, 10 Feb 2020 18:40:07 +0100 Subject: [PATCH 20/46] arm64: dts: allwinner: h6: orangepi-3: Add eMMC node OrangePi 3 can optionally have 8 GiB eMMC (soldered on board). Because those pins are dedicated to eMMC exclusively, node can be added for both variants (with and without eMMC). Kernel will then scan bus for presence of eMMC and act accordingly. Signed-off-by: Jernej Skrabec Signed-off-by: Maxime Ripard --- arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts index c311eee52a35..1e0abd9d047f 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts @@ -144,6 +144,15 @@ brcm: sdio-wifi@1 { }; }; +&mmc2 { + vmmc-supply = <®_cldo1>; + vqmmc-supply = <®_bldo2>; + cap-mmc-hw-reset; + non-removable; + bus-width = <8>; + status = "okay"; +}; + &ohci0 { status = "okay"; }; From fc976f50ae77c6a841803d816b057417b9b14293 Mon Sep 17 00:00:00 2001 From: Bastian Germann Date: Fri, 14 Feb 2020 12:10:02 +0100 Subject: [PATCH 21/46] dt-bindings: arm: sunxi: Add Linutronix Testbox Add device tree bindings for the newly added Linutronix Testbox board. Signed-off-by: Bastian Germann Signed-off-by: Maxime Ripard --- Documentation/devicetree/bindings/arm/sunxi.yaml | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml index 159060b65c5d..1e63c9867749 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.yaml +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml @@ -394,6 +394,12 @@ properties: - const: linksprite,pcduino3-nano - const: allwinner,sun7i-a20 + - description: Linutronix Testbox v2 + items: + - const: linutronix,testbox-v2 + - const: lamobo,lamobo-r1 + - const: allwinner,sun7i-a20 + - description: HAOYU Electronics Marsboard A10 items: - const: haoyu,a10-marsboard From 4c2bc78fe9d1c9aecc8a777221e3eb9d067987a8 Mon Sep 17 00:00:00 2001 From: Bastian Germann Date: Fri, 14 Feb 2020 12:10:03 +0100 Subject: [PATCH 22/46] ARM: dts: sun7i: Add Linutronix Testbox v2 board The Testbox board is an open hardware enhancement for the Lamobo R1 router board. The Testbox board is used in the CI-RT project to manage devices under test (https://ci-rt.linutronix.de). The hardware project is located at https://github.com/ci-rt/testbox-shield The Testbox v2 expands the Lamobo R1 router board with - a power supply, - a CAN bus PHY, - a power control, - a relay, - an I2C EEPROM, - a secure key storage (ATECC608a) and - two RS232 compliant serial ports. Co-developed-by: Benedikt Spranger Signed-off-by: Benedikt Spranger Signed-off-by: Bastian Germann [Maxime: Removed unused pinctrl node] Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/Makefile | 1 + .../dts/sun7i-a20-linutronix-testbox-v2.dts | 47 +++++++++++++++++++ 2 files changed, 48 insertions(+) create mode 100644 arch/arm/boot/dts/sun7i-a20-linutronix-testbox-v2.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index d6546d2676b9..e9ddca2946ce 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1086,6 +1086,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \ sun7i-a20-i12-tvbox.dtb \ sun7i-a20-icnova-swac.dtb \ sun7i-a20-lamobo-r1.dtb \ + sun7i-a20-linutronix-testbox-v2.dtb \ sun7i-a20-m3.dtb \ sun7i-a20-mk808c.dtb \ sun7i-a20-olimex-som-evb.dtb \ diff --git a/arch/arm/boot/dts/sun7i-a20-linutronix-testbox-v2.dts b/arch/arm/boot/dts/sun7i-a20-linutronix-testbox-v2.dts new file mode 100644 index 000000000000..da5a2eea4ce3 --- /dev/null +++ b/arch/arm/boot/dts/sun7i-a20-linutronix-testbox-v2.dts @@ -0,0 +1,47 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Copyright 2020 Linutronix GmbH + * Author: Benedikt Spranger + */ + +/dts-v1/; +#include "sun7i-a20-lamobo-r1.dts" + +/ { + model = "Lamobo R1"; + compatible = "linutronix,testbox-v2", "lamobo,lamobo-r1", "allwinner,sun7i-a20"; + + leds { + led-opto1 { + label = "lamobo_r1:opto:powerswitch"; + gpios = <&pio 7 3 GPIO_ACTIVE_HIGH>; + }; + + led-opto2 { + label = "lamobo_r1:opto:relay"; + gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + status = "okay"; + + eeprom: eeprom@50 { + compatible = "atmel,24c08"; + reg = <0x50>; + status = "okay"; + }; + + atecc508a@60 { + compatible = "atmel,atecc508a"; + reg = <0x60>; + }; +}; + +&can0 { + pinctrl-names = "default"; + pinctrl-0 = <&can_ph_pins>; + status = "okay"; +}; From 4e0e6a626bf4c35e043b4d547e91447f06139d27 Mon Sep 17 00:00:00 2001 From: Samuel Holland Date: Sun, 19 Jan 2020 10:30:58 -0600 Subject: [PATCH 23/46] arm64: dts: allwinner: pinebook: Remove unused AXP803 regulators The Pinebook does not use the CSI bus on the A64. In fact it does not use GPIO port E for anything at all. Thus the following regulators are not used and do not need voltages set: - ALDO1: Connected to VCC-PE only - DLDO3: Not connected - ELDO3: Not connected Signed-off-by: Samuel Holland Signed-off-by: Maxime Ripard --- .../boot/dts/allwinner/sun50i-a64-pinebook.dts | 16 +--------------- 1 file changed, 1 insertion(+), 15 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts index c06c540e6c08..12e513ba8f50 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -217,9 +217,7 @@ &battery_power_supply { }; ®_aldo1 { - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - regulator-name = "vcc-csi"; + regulator-name = "vcc-pe"; }; ®_aldo2 { @@ -282,12 +280,6 @@ ®_dldo2 { regulator-name = "vcc-edp"; }; -®_dldo3 { - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-name = "avdd-csi"; -}; - ®_dldo4 { regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; @@ -301,12 +293,6 @@ ®_eldo1 { regulator-name = "cpvdd"; }; -®_eldo3 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-name = "vdd-1v8-csi"; -}; - ®_fldo1 { regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; From 06f177c3daa0d419d900936407c367d2b0756eb1 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Mon, 10 Feb 2020 11:07:17 +0100 Subject: [PATCH 24/46] ARM: dts: sunxi: Remove redundant assigned-clocks The display backend nodes have an assigned clocks property, while the driver also enforces it. Since assigned-clocks is pretty fragile anyway, let's just remove it. Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun5i.dtsi | 3 --- arch/arm/boot/dts/sun6i-a31.dtsi | 6 ------ arch/arm/boot/dts/sun8i-a33.dtsi | 2 -- 3 files changed, 11 deletions(-) diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/sun5i.dtsi index 0b526e6e5a95..7f5cf028ce1a 100644 --- a/arch/arm/boot/dts/sun5i.dtsi +++ b/arch/arm/boot/dts/sun5i.dtsi @@ -771,9 +771,6 @@ be0: display-backend@1e60000 { interconnect-names = "dma-mem"; status = "disabled"; - assigned-clocks = <&ccu CLK_DE_BE>; - assigned-clock-rates = <300000000>; - ports { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi index 7762fbd9a133..f41440ecbdad 100644 --- a/arch/arm/boot/dts/sun6i-a31.dtsi +++ b/arch/arm/boot/dts/sun6i-a31.dtsi @@ -1139,9 +1139,6 @@ be1: display-backend@1e40000 { "ram"; resets = <&ccu RST_AHB1_BE1>; - assigned-clocks = <&ccu CLK_BE1>; - assigned-clock-rates = <300000000>; - ports { #address-cells = <1>; #size-cells = <0>; @@ -1231,9 +1228,6 @@ be0: display-backend@1e60000 { "ram"; resets = <&ccu RST_AHB1_BE0>; - assigned-clocks = <&ccu CLK_BE0>; - assigned-clock-rates = <300000000>; - ports { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/sun8i-a33.dtsi b/arch/arm/boot/dts/sun8i-a33.dtsi index 1532a0e59af4..d80c8a6856cf 100644 --- a/arch/arm/boot/dts/sun8i-a33.dtsi +++ b/arch/arm/boot/dts/sun8i-a33.dtsi @@ -372,8 +372,6 @@ &be0 { "ram", "sat"; resets = <&ccu RST_BUS_DE_BE>, <&ccu RST_BUS_SAT>; reset-names = "be", "sat"; - assigned-clocks = <&ccu CLK_DE_BE>; - assigned-clock-rates = <300000000>; }; &ccu { From 692b4363c456ab237f95b414a2f439a6dbc9ab15 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Mon, 10 Feb 2020 11:07:18 +0100 Subject: [PATCH 25/46] ARM: dts: sunxi: Remove redundant assigned-clocks The display DRC nodes have an assigned clocks property, while the driver also enforces it. Since assigned-clocks is pretty fragile anyway, let's just remove it. Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun6i-a31.dtsi | 6 ------ arch/arm/boot/dts/sun8i-a23-a33.dtsi | 3 --- 2 files changed, 9 deletions(-) diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi index f41440ecbdad..f3425a66fc0a 100644 --- a/arch/arm/boot/dts/sun6i-a31.dtsi +++ b/arch/arm/boot/dts/sun6i-a31.dtsi @@ -1182,9 +1182,6 @@ drc1: drc@1e50000 { "ram"; resets = <&ccu RST_AHB1_DRC1>; - assigned-clocks = <&ccu CLK_IEP_DRC1>; - assigned-clock-rates = <300000000>; - ports { #address-cells = <1>; #size-cells = <0>; @@ -1268,9 +1265,6 @@ drc0: drc@1e70000 { "ram"; resets = <&ccu RST_AHB1_DRC0>; - assigned-clocks = <&ccu CLK_IEP_DRC0>; - assigned-clock-rates = <300000000>; - ports { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/sun8i-a23-a33.dtsi b/arch/arm/boot/dts/sun8i-a23-a33.dtsi index 48487f6d4ab9..c1362d0f0ff8 100644 --- a/arch/arm/boot/dts/sun8i-a23-a33.dtsi +++ b/arch/arm/boot/dts/sun8i-a23-a33.dtsi @@ -684,9 +684,6 @@ drc0: drc@1e70000 { clock-names = "ahb", "mod", "ram"; resets = <&ccu RST_BUS_DRC>; - assigned-clocks = <&ccu CLK_DRC>; - assigned-clock-rates = <300000000>; - ports { #address-cells = <1>; #size-cells = <0>; From 564c4815074291c40a584b1b05da3732beac990c Mon Sep 17 00:00:00 2001 From: Andrey Lebedev Date: Wed, 19 Feb 2020 20:08:56 +0200 Subject: [PATCH 26/46] ARM: dts: sun7i: Add LVDS panel support on A20 Define pins for LVDS channels 0 and 1, configure reset line for tcon0 and provide sample LVDS panel, connected to tcon0. Signed-off-by: Andrey Lebedev Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun7i-a20.dtsi | 25 +++++++++++++++++++++---- 1 file changed, 21 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi index 92b5be97085d..ffe1d10a1a84 100644 --- a/arch/arm/boot/dts/sun7i-a20.dtsi +++ b/arch/arm/boot/dts/sun7i-a20.dtsi @@ -47,6 +47,7 @@ #include #include #include +#include / { interrupt-parent = <&gic>; @@ -404,11 +405,12 @@ mdio: mdio@1c0b080 { }; tcon0: lcd-controller@1c0c000 { - compatible = "allwinner,sun7i-a20-tcon"; + compatible = "allwinner,sun7i-a20-tcon0", + "allwinner,sun7i-a20-tcon"; reg = <0x01c0c000 0x1000>; interrupts = ; - resets = <&ccu RST_TCON0>; - reset-names = "lcd"; + resets = <&ccu RST_TCON0>, <&ccu RST_LVDS>; + reset-names = "lcd", "lvds"; clocks = <&ccu CLK_AHB_LCD0>, <&ccu CLK_TCON0_CH0>, <&ccu CLK_TCON0_CH1>; @@ -454,7 +456,8 @@ tcon0_out_hdmi: endpoint@1 { }; tcon1: lcd-controller@1c0d000 { - compatible = "allwinner,sun7i-a20-tcon"; + compatible = "allwinner,sun7i-a20-tcon1", + "allwinner,sun7i-a20-tcon"; reg = <0x01c0d000 0x1000>; interrupts = ; resets = <&ccu RST_TCON1>; @@ -931,6 +934,20 @@ ir1_tx_pin: ir1-tx-pin { function = "ir1"; }; + /omit-if-no-ref/ + lcd_lvds0_pins: lcd-lvds0-pins { + pins = "PD0", "PD1", "PD2", "PD3", "PD4", + "PD5", "PD6", "PD7", "PD8", "PD9"; + function = "lvds0"; + }; + + /omit-if-no-ref/ + lcd_lvds1_pins: lcd-lvds1-pins { + pins = "PD10", "PD11", "PD12", "PD13", "PD14", + "PD15", "PD16", "PD17", "PD18", "PD19"; + function = "lvds1"; + }; + /omit-if-no-ref/ mmc0_pins: mmc0-pins { pins = "PF0", "PF1", "PF2", From 7efbada45edc660d59cee2842726b5bb1a8b0322 Mon Sep 17 00:00:00 2001 From: Ondrej Jirman Date: Sun, 23 Feb 2020 04:16:13 +0100 Subject: [PATCH 27/46] dt-bindings: arm: sunxi: Add PocketBook Touch Lux 3 Add a new board name. Signed-off-by: Ondrej Jirman Signed-off-by: Maxime Ripard --- Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml index 1e63c9867749..5b22b77e4bb7 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.yaml +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml @@ -658,6 +658,11 @@ properties: - const: pineriver,mini-xplus - const: allwinner,sun4i-a10 + - description: PocketBook Touch Lux 3 + items: + - const: pocketbook,touch-lux-3 + - const: allwinner,sun5i-a13 + - description: Point of View Protab2-IPS9 items: - const: pov,protab2-ips9 From cd3e42c9f7458a65fd3b26716230c0ee45a6344f Mon Sep 17 00:00:00 2001 From: Ondrej Jirman Date: Sun, 23 Feb 2020 04:16:14 +0100 Subject: [PATCH 28/46] ARM: dts: sun5i: Add PocketBook Touch Lux 3 support What works: - Serial console - mmc0, mmc2 (both microSD card slots on the board) - All buttons (gpio and lradc based) - Power LED - PMIC - RTC - USB OTG/gadgets mode - Realtek USB WiFi - Display backlight - eInk display SPI NOR flash memory Signed-off-by: Ondrej Jirman Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/Makefile | 1 + .../dts/sun5i-a13-pocketbook-touch-lux-3.dts | 257 ++++++++++++++++++ 2 files changed, 258 insertions(+) create mode 100644 arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index e9ddca2946ce..78f144e332f6 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1056,6 +1056,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \ sun5i-a13-licheepi-one.dtb \ sun5i-a13-olinuxino.dtb \ sun5i-a13-olinuxino-micro.dtb \ + sun5i-a13-pocketbook-touch-lux-3.dtb \ sun5i-a13-q8-tablet.dtb \ sun5i-a13-utoo-p66.dtb \ sun5i-gr8-chip-pro.dtb \ diff --git a/arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts b/arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts new file mode 100644 index 000000000000..e9ef97c9c893 --- /dev/null +++ b/arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts @@ -0,0 +1,257 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright 2019 Ondrej Jirman + */ + +/dts-v1/; +#include "sun5i-a13.dtsi" +#include "sunxi-common-regulators.dtsi" +#include +#include +#include +#include + +/ { + model = "PocketBook Touch Lux 3"; + compatible = "pocketbook,touch-lux-3", "allwinner,sun5i-a13"; + + aliases { + serial0 = &uart1; + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>; + enable-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ + brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; + default-brightness-level = <8>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + power { + gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */ + default-state = "on"; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + autorepeat; + label = "GPIO Keys"; + + key-right { + label = "Right"; + linux,code = ; + gpios = <&pio 6 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG9 */ + }; + + key-left { + label = "Left"; + linux,code = ; + gpios = <&pio 6 10 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG10 */ + }; + }; + + reg_1v8: regulator-1v8 { + compatible = "regulator-fixed"; + regulator-name = "vdd-1v8-nor-ctp"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&pio 2 15 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_1v8_nor: regulator-nor { + compatible = "regulator-fixed"; + regulator-name = "vdd-nor"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&pio 2 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <®_1v8>; + regulator-always-on; + }; + + reg_1v8_ctp: regulator-ctp { + compatible = "regulator-fixed"; + regulator-name = "vdd-ctp"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&pio 2 13 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <®_1v8>; + }; + + reg_3v3_mmc0: regulator-mmc0 { + compatible = "regulator-fixed"; + regulator-name = "vdd-mmc0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pio 4 4 GPIO_ACTIVE_LOW>; /* PE4 */ + vin-supply = <®_vcc3v3>; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&ehci0 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + axp209: pmic@34 { + reg = <0x34>; + interrupts = <0>; + }; +}; + +#include "axp209.dtsi" + +&i2c1 { + status = "okay"; + + pcf8563: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; +}; + +&i2c2 { + status = "okay"; + + /* Touchpanel is connected here. */ +}; + +&lradc { + vref-supply = <®_ldo2>; + status = "okay"; + + button-200 { + label = "Home"; + linux,code = ; + channel = <0>; + voltage = <200000>; + }; + + button-400 { + label = "Menu"; + linux,code = ; + channel = <0>; + voltage = <400000>; + }; +}; + +&mmc0 { + vmmc-supply = <®_3v3_mmc0>; + bus-width = <4>; + cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */ + status = "okay"; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_4bit_pc_pins>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&otg_sram { + status = "okay"; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pin>; + status = "okay"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vdd-int-pll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_ldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; + /* We need this otherwise the LDO3 would overload */ + regulator-soft-start; + regulator-ramp-delay = <1600>; +}; + +&spi2 { + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pe_pins>, <&spi2_cs0_pe_pin>; + status = "okay"; + + epd_flash: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "macronix,mx25u4033", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <4000000>; + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pg_pins>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "peripheral"; + status = "okay"; +}; + +&battery_power_supply { + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + +&usbphy { + usb1_vbus-supply = <®_ldo3>; + status = "okay"; +}; From 3abe422fdc65ba08054659b0d27c71e24346021d Mon Sep 17 00:00:00 2001 From: Ondrej Jirman Date: Sun, 23 Feb 2020 11:40:19 +0100 Subject: [PATCH 29/46] arm64: dts: sun50i-h5-orange-pi-pc2: Add CPUX voltage regulator Orange Pi PC2 features sy8106a regulator just like Orange Pi PC. Signed-off-by: Ondrej Jirman Reviewed-by: Samuel Holland Signed-off-by: Maxime Ripard --- .../dts/allwinner/sun50i-h5-orangepi-pc2.dts | 20 +++++++++++++++++++ 1 file changed, 20 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts index c4f89c312f42..7d7aad18f078 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts @@ -94,6 +94,10 @@ &codec { status = "okay"; }; +&cpu0 { + cpu-supply = <®_vdd_cpux>; +}; + &de { status = "okay"; }; @@ -169,6 +173,22 @@ &ohci3 { status = "okay"; }; +&r_i2c { + status = "okay"; + + reg_vdd_cpux: regulator@65 { + compatible = "silergy,sy8106a"; + reg = <0x65>; + regulator-name = "vdd-cpux"; + silergy,fixed-microvolt = <1100000>; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-ramp-delay = <200>; + regulator-boot-on; + regulator-always-on; + }; +}; + &spi0 { status = "okay"; From 9680d194d53f035c45c0e0153b1996c5fb6f55d5 Mon Sep 17 00:00:00 2001 From: Ondrej Jirman Date: Sat, 22 Feb 2020 23:31:54 +0100 Subject: [PATCH 30/46] ARM: dts: sun8i-a83t-tbs-a711: Drop superfluous dr_mode Property dr_mode = "otg" is the default in sun8i-a83t.dtsi Signed-off-by: Ondrej Jirman Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts b/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts index 2fd31a0a0b34..4ab4568de8c6 100644 --- a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts +++ b/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts @@ -493,7 +493,6 @@ gnss { }; &usb_otg { - dr_mode = "otg"; status = "okay"; }; From 4ae7a3c3d7d31260f690d8d658f0365f3eca67a2 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Mon, 10 Feb 2020 10:55:59 +0100 Subject: [PATCH 31/46] arm64: dts: allwinner: h5: Fix PMU compatible The commit c35a516a4618 ("arm64: dts: allwinner: H5: Add PMU node") introduced support for the PMU found on the Allwinner H5. However, the binding only allows for a single compatible, while the patch was adding two. Make sure we follow the binding. Fixes: c35a516a4618 ("arm64: dts: allwinner: H5: Add PMU node") Signed-off-by: Maxime Ripard --- arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi index 9893aa64dd0b..4462a68c0681 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi @@ -38,8 +38,7 @@ cpu3: cpu@3 { }; pmu { - compatible = "arm,cortex-a53-pmu", - "arm,armv8-pmuv3"; + compatible = "arm,cortex-a53-pmu"; interrupts = , , , From 4c7eeb9af3e41ae7d840977119c58f3bbb3f4f59 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Mon, 10 Feb 2020 10:56:00 +0100 Subject: [PATCH 32/46] arm64: dts: allwinner: h6: Fix PMU compatible The commit 7aa9b9eb7d6a ("arm64: dts: allwinner: H6: Add PMU mode") introduced support for the PMU found on the Allwinner H6. However, the binding only allows for a single compatible, while the patch was adding two. Make sure we follow the binding. Fixes: 7aa9b9eb7d6a ("arm64: dts: allwinner: H6: Add PMU mode") Signed-off-by: Maxime Ripard --- arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi index 41b58ffa8596..967249e58811 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi @@ -70,8 +70,7 @@ ext_osc32k: ext_osc32k_clk { }; pmu { - compatible = "arm,cortex-a53-pmu", - "arm,armv8-pmuv3"; + compatible = "arm,cortex-a53-pmu"; interrupts = , , , From 7ad9f3d0cb2f2b886c068f99e791bd41ceb0677a Mon Sep 17 00:00:00 2001 From: Ondrej Jirman Date: Mon, 24 Feb 2020 17:54:46 +0100 Subject: [PATCH 33/46] ARM: dts: sun8i-h3: Add thermal trip points/cooling maps MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This enables passive cooling by down-regulating CPU voltage and frequency. For trip points, I used a slightly lowered values from the BSP code. The critical temperature of 110°C from BSP code seemed like a lot, so I rounded it off to 100°C. The critical trip point value is 30°C above the maximum recommended ambient temperature (70°C) for the SoC from the datasheet, so there's some headroom even at such a high ambient temperature. Signed-off-by: Ondrej Jirman Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-h3.dtsi | 25 +++++++++++++++++++++++++ 1 file changed, 25 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi index 20217e2ca4d3..e83aa6866e7e 100644 --- a/arch/arm/boot/dts/sun8i-h3.dtsi +++ b/arch/arm/boot/dts/sun8i-h3.dtsi @@ -41,6 +41,7 @@ */ #include "sunxi-h3-h5.dtsi" +#include / { cpu0_opp_table: opp_table0 { @@ -227,6 +228,30 @@ cpu_thermal: cpu-thermal { polling-delay-passive = <0>; polling-delay = <0>; thermal-sensors = <&ths 0>; + + trips { + cpu_hot_trip: cpu-hot { + temperature = <80000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu_very_hot_trip: cpu-very-hot { + temperature = <100000>; + hysteresis = <0>; + type = "critical"; + }; + }; + + cooling-maps { + cpu-hot-limit { + trip = <&cpu_hot_trip>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; }; }; From 87bf7a5fba68b0ab3b34fbb06b5aa6cbb9dcc9a1 Mon Sep 17 00:00:00 2001 From: Ondrej Jirman Date: Mon, 24 Feb 2020 17:54:17 +0100 Subject: [PATCH 34/46] ARM: dts: sun8i-a83t: Add thermal trip points/cooling maps MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This enables passive cooling by down-regulating CPU voltage and frequency. For the trip points, I used values from the BSP code directly. The critical trip point value is 30°C above the maximum recommended ambient temperature (70°C) for the SoC from the datasheet, so there's some headroom even at such a high ambient temperature. Signed-off-by: Ondrej Jirman Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sun8i-a83t.dtsi | 60 +++++++++++++++++++++++++++---- 1 file changed, 54 insertions(+), 6 deletions(-) diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi index 74ac7ee9383c..53c2b6a836f2 100644 --- a/arch/arm/boot/dts/sun8i-a83t.dtsi +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi @@ -72,7 +72,7 @@ cpu0: cpu@0 { #cooling-cells = <2>; }; - cpu@1 { + cpu1: cpu@1 { compatible = "arm,cortex-a7"; device_type = "cpu"; clocks = <&ccu CLK_C0CPUX>; @@ -83,7 +83,7 @@ cpu@1 { #cooling-cells = <2>; }; - cpu@2 { + cpu2: cpu@2 { compatible = "arm,cortex-a7"; device_type = "cpu"; clocks = <&ccu CLK_C0CPUX>; @@ -94,7 +94,7 @@ cpu@2 { #cooling-cells = <2>; }; - cpu@3 { + cpu3: cpu@3 { compatible = "arm,cortex-a7"; device_type = "cpu"; clocks = <&ccu CLK_C0CPUX>; @@ -116,7 +116,7 @@ cpu100: cpu@100 { #cooling-cells = <2>; }; - cpu@101 { + cpu101: cpu@101 { compatible = "arm,cortex-a7"; device_type = "cpu"; clocks = <&ccu CLK_C1CPUX>; @@ -127,7 +127,7 @@ cpu@101 { #cooling-cells = <2>; }; - cpu@102 { + cpu102: cpu@102 { compatible = "arm,cortex-a7"; device_type = "cpu"; clocks = <&ccu CLK_C1CPUX>; @@ -138,7 +138,7 @@ cpu@102 { #cooling-cells = <2>; }; - cpu@103 { + cpu103: cpu@103 { compatible = "arm,cortex-a7"; device_type = "cpu"; clocks = <&ccu CLK_C1CPUX>; @@ -1188,12 +1188,60 @@ cpu0_thermal: cpu0-thermal { polling-delay-passive = <0>; polling-delay = <0>; thermal-sensors = <&ths 0>; + + trips { + cpu0_hot: cpu-hot { + temperature = <80000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu0_very_hot: cpu-very-hot { + temperature = <100000>; + hysteresis = <0>; + type = "critical"; + }; + }; + + cooling-maps { + cpu-hot-limit { + trip = <&cpu0_hot>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; cpu1_thermal: cpu1-thermal { polling-delay-passive = <0>; polling-delay = <0>; thermal-sensors = <&ths 1>; + + trips { + cpu1_hot: cpu-hot { + temperature = <80000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu1_very_hot: cpu-very-hot { + temperature = <100000>; + hysteresis = <0>; + type = "critical"; + }; + }; + + cooling-maps { + cpu-hot-limit { + trip = <&cpu1_hot>; + cooling-device = <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu102 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu103 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; }; gpu_thermal: gpu-thermal { From 4098a2b45bb3fc2e928487c064974be26c7f6128 Mon Sep 17 00:00:00 2001 From: Icenowy Zheng Date: Wed, 26 Feb 2020 00:10:11 -0800 Subject: [PATCH 35/46] arm64: allwinner: a64: enable LCD-related hardware for Pinebook Pinebook has an ANX6345 bridge connected to the RGB666 LCD output and eDP panel input. The bridge is controlled via I2C that's connected to R_I2C bus. Enable all this hardware in device tree. Reviewed-by: Laurent Pinchart Signed-off-by: Icenowy Zheng Signed-off-by: Vasily Khoruzhick Signed-off-by: Maxime Ripard --- .../dts/allwinner/sun50i-a64-pinebook.dts | 61 ++++++++++++++++++- 1 file changed, 60 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts index 12e513ba8f50..64b1c54f87c0 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -48,6 +48,18 @@ lid_switch { }; }; + panel_edp: panel-edp { + compatible = "neweast,wjfh116008a"; + backlight = <&backlight>; + power-supply = <®_dc1sw>; + + port { + panel_edp_in: endpoint { + remote-endpoint = <&anx6345_out_edp>; + }; + }; + }; + reg_vbklt: vbklt { compatible = "regulator-fixed"; regulator-name = "vbklt"; @@ -109,6 +121,10 @@ &dai { status = "okay"; }; +&de { + status = "okay"; +}; + &ehci0 { phys = <&usbphy 0>; phy-names = "usb"; @@ -119,6 +135,10 @@ &ehci1 { status = "okay"; }; +&mixer0 { + status = "okay"; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; @@ -177,12 +197,38 @@ &pwm { status = "okay"; }; -/* The ANX6345 eDP-bridge is on r_i2c */ &r_i2c { clock-frequency = <100000>; pinctrl-names = "default"; pinctrl-0 = <&r_i2c_pl89_pins>; status = "okay"; + + anx6345: anx6345@38 { + compatible = "analogix,anx6345"; + reg = <0x38>; + reset-gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */ + dvdd25-supply = <®_dldo2>; + dvdd12-supply = <®_fldo1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + anx6345_in: port@0 { + reg = <0>; + anx6345_in_tcon0: endpoint { + remote-endpoint = <&tcon0_out_anx6345>; + }; + }; + + anx6345_out: port@1 { + reg = <1>; + anx6345_out_edp: endpoint { + remote-endpoint = <&panel_edp_in>; + }; + }; + }; + }; }; &r_pio { @@ -343,6 +389,19 @@ &sound { "MIC2", "Internal Microphone Right"; }; +&tcon0 { + pinctrl-names = "default"; + pinctrl-0 = <&lcd_rgb666_pins>; + + status = "okay"; +}; + +&tcon0_out { + tcon0_out_anx6345: endpoint { + remote-endpoint = <&anx6345_in_tcon0>; + }; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pb_pins>; From 179a79fd740b6b2f66b64bae5cb6ecd483987d20 Mon Sep 17 00:00:00 2001 From: Mans Rullgard Date: Thu, 27 Feb 2020 11:55:26 +0000 Subject: [PATCH 36/46] ARM: dts: sunxi: h3/h5: add r_pwm node There is a second PWM unit available in the PL I/O block. Add a node and pinmux definition for it. Signed-off-by: Mans Rullgard Signed-off-by: Maxime Ripard --- arch/arm/boot/dts/sunxi-h3-h5.dtsi | 15 +++++++++++++++ 1 file changed, 15 insertions(+) diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi index 5e9c3060aa08..ed3908849111 100644 --- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi @@ -892,6 +892,21 @@ r_i2c_pins: r-i2c-pins { pins = "PL0", "PL1"; function = "s_i2c"; }; + + r_pwm_pin: r-pwm-pin { + pins = "PL10"; + function = "s_pwm"; + }; + }; + + r_pwm: pwm@1f03800 { + compatible = "allwinner,sun8i-h3-pwm"; + reg = <0x01f03800 0x8>; + pinctrl-names = "default"; + pinctrl-0 = <&r_pwm_pin>; + clocks = <&osc24M>; + #pwm-cells = <3>; + status = "disabled"; }; }; }; From 29b2c68bf47a571fdae64c35060173fc4ad88dbe Mon Sep 17 00:00:00 2001 From: Ondrej Jirman Date: Thu, 27 Feb 2020 02:26:48 +0100 Subject: [PATCH 37/46] arm64: dts: sun50i-a64: Add i2c2 pins PinePhone needs I2C2 pins description. Add it, and make it default for i2c2, since it's the only possiblilty. Signed-off-by: Ondrej Jirman Signed-off-by: Maxime Ripard --- arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi index 72b1b34879c6..990de71ca048 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi @@ -671,6 +671,11 @@ i2c1_pins: i2c1-pins { function = "i2c1"; }; + i2c2_pins: i2c2-pins { + pins = "PE14", "PE15"; + function = "i2c2"; + }; + /omit-if-no-ref/ lcd_rgb666_pins: lcd-rgb666-pins { pins = "PD0", "PD1", "PD2", "PD3", "PD4", @@ -958,12 +963,13 @@ i2c2: i2c@1c2b400 { interrupts = ; clocks = <&ccu CLK_BUS_I2C2>; resets = <&ccu RST_BUS_I2C2>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; }; - spi0: spi@1c68000 { compatible = "allwinner,sun8i-h3-spi"; reg = <0x01c68000 0x1000>; From a886ed26568646cb542866207563e2ad9afcde69 Mon Sep 17 00:00:00 2001 From: Ondrej Jirman Date: Thu, 27 Feb 2020 02:26:49 +0100 Subject: [PATCH 38/46] dt-bindings: arm: sunxi: Add PinePhone 1.0 and 1.1 bindings Document board compatible names for Pine64 PinePhone: - 1.0 - Developer variant - 1.1 - Braveheart variant Signed-off-by: Ondrej Jirman Reviewed-by: Rob Herring Signed-off-by: Maxime Ripard --- Documentation/devicetree/bindings/arm/sunxi.yaml | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml index 5b22b77e4bb7..abf2d97fb7ae 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.yaml +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml @@ -642,6 +642,16 @@ properties: - const: pine64,pinebook - const: allwinner,sun50i-a64 + - description: Pine64 PinePhone Developer Batch (1.0) + items: + - const: pine64,pinephone-1.0 + - const: allwinner,sun50i-a64 + + - description: Pine64 PinePhone Braveheart (1.1) + items: + - const: pine64,pinephone-1.1 + - const: allwinner,sun50i-a64 + - description: Pine64 PineTab items: - const: pine64,pinetab From 91f480d409429db29b402c3200e4a6f1e519ba87 Mon Sep 17 00:00:00 2001 From: Ondrej Jirman Date: Thu, 27 Feb 2020 02:26:50 +0100 Subject: [PATCH 39/46] arm64: dts: allwinner: Add initial support for Pine64 PinePhone At the moment PinePhone comes in two slightly incompatible variants: - 1.0: Early Developer Batch - 1.1: Braveheart Batch There will be at least one more incompatible variant in the very near future, so let's start by sharing the dtsi among multiple variants, right away, even though the HW description doesn't yet include the different bits. The differences between 1.0 and 1.1 are: change in pins that control the flash LED, differences in modem power status signal routing, and maybe some other subtler things, that have not been determined yet. This is a basic DT that includes only features that are already supported by mainline drivers. Co-developed-by: Samuel Holland Signed-off-by: Samuel Holland Co-developed-by: Martijn Braam Signed-off-by: Martijn Braam Co-developed-by: Luca Weiss Signed-off-by: Luca Weiss Signed-off-by: Bhushan Shah Signed-off-by: Icenowy Zheng Signed-off-by: Ondrej Jirman Signed-off-by: Maxime Ripard --- arch/arm64/boot/dts/allwinner/Makefile | 2 + .../allwinner/sun50i-a64-pinephone-1.0.dts | 11 + .../allwinner/sun50i-a64-pinephone-1.1.dts | 11 + .../dts/allwinner/sun50i-a64-pinephone.dtsi | 379 ++++++++++++++++++ 4 files changed, 403 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index 6dad63881cd3..e4d3cd0ac5bb 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -9,6 +9,8 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-orangepi-win.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-lts.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinebook.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.0.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.1.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts new file mode 100644 index 000000000000..0c42272106af --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2020 Ondrej Jirman + +/dts-v1/; + +#include "sun50i-a64-pinephone.dtsi" + +/ { + model = "Pine64 PinePhone Developer Batch (1.0)"; + compatible = "pine64,pinephone-1.0", "allwinner,sun50i-a64"; +}; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts new file mode 100644 index 000000000000..06a775c41664 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2020 Ondrej Jirman + +/dts-v1/; + +#include "sun50i-a64-pinephone.dtsi" + +/ { + model = "Pine64 PinePhone Braveheart (1.1)"; + compatible = "pine64,pinephone-1.1", "allwinner,sun50i-a64"; +}; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi new file mode 100644 index 000000000000..cefda145c3c9 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi @@ -0,0 +1,379 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2019 Icenowy Zheng +// Copyright (C) 2020 Martijn Braam +// Copyright (C) 2020 Ondrej Jirman + +#include "sun50i-a64.dtsi" +#include "sun50i-a64-cpu-opp.dtsi" + +#include +#include +#include +#include + +/ { + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + blue { + function = LED_FUNCTION_INDICATOR; + color = ; + gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */ + }; + + green { + function = LED_FUNCTION_INDICATOR; + color = ; + gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */ + }; + + red { + function = LED_FUNCTION_INDICATOR; + color = ; + gpios = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */ + }; + }; + + speaker_amp: audio-amplifier { + compatible = "simple-audio-amplifier"; + enable-gpios = <&pio 2 7 GPIO_ACTIVE_HIGH>; /* PC7 */ + sound-name-prefix = "Speaker Amp"; + }; + + vibrator { + compatible = "gpio-vibrator"; + enable-gpios = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */ + vcc-supply = <®_dcdc1>; + }; +}; + +&codec { + status = "okay"; +}; + +&codec_analog { + cpvdd-supply = <®_eldo1>; + status = "okay"; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&cpu1 { + cpu-supply = <®_dcdc2>; +}; + +&cpu2 { + cpu-supply = <®_dcdc2>; +}; + +&cpu3 { + cpu-supply = <®_dcdc2>; +}; + +&dai { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&i2c1 { + status = "okay"; + + /* Magnetometer */ + lis3mdl@1e { + compatible = "st,lis3mdl-magn"; + reg = <0x1e>; + vdd-supply = <®_dldo1>; + vddio-supply = <®_dldo1>; + }; + + /* Accelerometer/gyroscope */ + mpu6050@68 { + compatible = "invensense,mpu6050"; + reg = <0x68>; + interrupt-parent = <&pio>; + interrupts = <7 5 IRQ_TYPE_EDGE_RISING>; /* PH5 */ + vdd-supply = <®_dldo1>; + vddio-supply = <®_dldo1>; + }; +}; + +/* Connected to pogo pins (external spring based pinheader for user addons) */ +&i2c2 { + status = "okay"; +}; + +&lradc { + vref-supply = <®_aldo3>; + status = "okay"; + + button-200 { + label = "Volume Up"; + linux,code = ; + channel = <0>; + voltage = <200000>; + }; + + button-400 { + label = "Volume Down"; + linux,code = ; + channel = <0>; + voltage = <400000>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + disable-wp; + bus-width = <4>; + status = "okay"; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&pio { + vcc-pb-supply = <®_dcdc1>; + vcc-pc-supply = <®_dcdc1>; + vcc-pd-supply = <®_dcdc1>; + vcc-pe-supply = <®_aldo1>; + vcc-pf-supply = <®_dcdc1>; + vcc-pg-supply = <®_dldo4>; + vcc-ph-supply = <®_dcdc1>; +}; + +&r_pio { + /* + * FIXME: We can't add that supply for now since it would + * create a circular dependency between pinctrl, the regulator + * and the RSB Bus. + * + * vcc-pl-supply = <®_aldo2>; + */ +}; + +&r_rsb { + status = "okay"; + + axp803: pmic@3a3 { + compatible = "x-powers,axp803"; + reg = <0x3a3>; + interrupt-parent = <&r_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +#include "axp803.dtsi" + +&ac_power_supply { + status = "okay"; +}; + +&battery_power_supply { + status = "okay"; +}; + +®_aldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dovdd-csi"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-pl"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pll-avcc"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd-cpux"; +}; + +/* DCDC3 is polyphased with DCDC2 */ + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-sys"; +}; + +®_dldo1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-dsi-sensor"; +}; + +®_dldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-mipi-io"; +}; + +®_dldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi"; +}; + +®_dldo4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-io"; +}; + +®_eldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-lpddr"; +}; + +®_eldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dvdd-1v8-csi"; +}; + +®_fldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-1v2-hsic"; +}; + +®_fldo2 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_ldo_io0 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-lcd-ctp-stk"; + status = "okay"; +}; + +®_ldo_io1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-1v8-typec"; + status = "okay"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; +}; + +&sound { + status = "okay"; + simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>; + simple-audio-card,widgets = "Microphone", "Headset Microphone", + "Microphone", "Internal Microphone", + "Headphone", "Headphone Jack", + "Speaker", "Internal Earpiece", + "Speaker", "Internal Speaker"; + simple-audio-card,routing = + "Headphone Jack", "HP", + "Internal Earpiece", "EARPIECE", + "Internal Speaker", "Speaker Amp OUTL", + "Internal Speaker", "Speaker Amp OUTR", + "Speaker Amp INL", "LINEOUT", + "Speaker Amp INR", "LINEOUT", + "Left DAC", "AIF1 Slot 0 Left", + "Right DAC", "AIF1 Slot 0 Right", + "AIF1 Slot 0 Left ADC", "Left ADC", + "AIF1 Slot 0 Right ADC", "Right ADC", + "Internal Microphone", "MBIAS", + "MIC1", "Internal Microphone", + "Headset Microphone", "HBIAS", + "MIC2", "Headset Microphone"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pb_pins>; + status = "okay"; +}; + +/* Connected to the modem (hardware flow control can't be used) */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "peripheral"; + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; From 32507b8681198c987fad8ac66e55ad4e15dfae4a Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Sun, 8 Mar 2020 14:58:49 +0100 Subject: [PATCH 40/46] arm64: dts: allwinner: h6: Move ext. oscillator to board DTs It turns out that not all H6 boards have external 32kHz oscillator. Currently the only one known such H6 board is Tanix TX6. Move external oscillator node from common H6 dtsi to board specific dts files where present. Signed-off-by: Jernej Skrabec Signed-off-by: Maxime Ripard --- .../boot/dts/allwinner/sun50i-h6-beelink-gs1.dts | 11 +++++++++++ .../arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts | 11 +++++++++++ arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi | 11 +++++++++++ arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts | 11 +++++++++++ arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 8 -------- 5 files changed, 44 insertions(+), 8 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts index df6d872c34e2..8f09d209359b 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts @@ -32,6 +32,13 @@ hdmi_con_in: endpoint { }; }; + ext_osc32k: ext_osc32k_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "ext_osc32k"; + }; + leds { compatible = "gpio-leds"; @@ -275,6 +282,10 @@ &r_pio { vcc-pm-supply = <®_aldo1>; }; +&rtc { + clocks = <&ext_osc32k>; +}; + &spdif { status = "okay"; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts index 1e0abd9d047f..47f579610dcc 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts @@ -32,6 +32,13 @@ hdmi_con_in: endpoint { }; }; + ext_osc32k: ext_osc32k_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "ext_osc32k"; + }; + leds { compatible = "gpio-leds"; @@ -285,6 +292,10 @@ &r_ir { status = "okay"; }; +&rtc { + clocks = <&ext_osc32k>; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_ph_pins>; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi index 37f4c57597d4..37fc3f3697f7 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi @@ -20,6 +20,13 @@ chosen { stdout-path = "serial0:115200n8"; }; + ext_osc32k: ext_osc32k_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "ext_osc32k"; + }; + leds { compatible = "gpio-leds"; @@ -197,6 +204,10 @@ &r_ir { status = "okay"; }; +&rtc { + clocks = <&ext_osc32k>; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_ph_pins>; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts index 3c9dd0d69754..b0642d841933 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts @@ -21,6 +21,13 @@ chosen { stdout-path = "serial0:115200n8"; }; + ext_osc32k: ext_osc32k_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + clock-output-names = "ext_osc32k"; + }; + hdmi_connector: connector { compatible = "hdmi-connector"; type = "a"; @@ -279,6 +286,10 @@ &r_pio { vcc-pm-supply = <®_aldo1>; }; +&rtc { + clocks = <&ext_osc32k>; +}; + /* * The CS pin is shared with the MMC2 CMD pin, so we cannot have the SPI * flash and eMMC at the same time, as one of them would fail probing. diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi index 967249e58811..b9ab7d8fa8af 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi @@ -62,13 +62,6 @@ osc24M: osc24M_clk { clock-output-names = "osc24M"; }; - ext_osc32k: ext_osc32k_clk { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <32768>; - clock-output-names = "ext_osc32k"; - }; - pmu { compatible = "arm,cortex-a53-pmu"; interrupts = , @@ -854,7 +847,6 @@ rtc: rtc@7000000 { interrupts = , ; clock-output-names = "osc32k", "osc32k-out", "iosc"; - clocks = <&ext_osc32k>; #clock-cells = <1>; }; From 7ee32a17e0d65fbaa55b032f3bb52232b09fb447 Mon Sep 17 00:00:00 2001 From: Marcus Cooper Date: Sun, 8 Mar 2020 17:48:39 +0100 Subject: [PATCH 41/46] arm64: dts: allwinner: h6: orangepi-one-plus: Enable ethernet OrangePi One Plus has gigabit ethernet. Add nodes for it. Signed-off-by: Marcus Cooper [patch split and commit message] Signed-off-by: Jernej Skrabec Reviewed-by: Christopher Obbard Tested-by: Christopher Obbard Signed-off-by: Maxime Ripard --- .../allwinner/sun50i-h6-orangepi-one-plus.dts | 33 +++++++++++++++++++ 1 file changed, 33 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts index 83aab7368889..fceb298bfd53 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-one-plus.dts @@ -7,4 +7,37 @@ / { model = "OrangePi One Plus"; compatible = "xunlong,orangepi-one-plus", "allwinner,sun50i-h6"; + + aliases { + ethernet0 = &emac; + }; + + reg_gmac_3v3: gmac-3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc-gmac-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <100000>; + enable-active-high; + gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */ + vin-supply = <®_aldo2>; + }; +}; + +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&ext_rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + phy-supply = <®_gmac_3v3>; + allwinner,rx-delay-ps = <200>; + allwinner,tx-delay-ps = <200>; + status = "okay"; +}; + +&mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; }; From 2345b744f4f911713dcada64ea16a614f5be9328 Mon Sep 17 00:00:00 2001 From: Marcus Cooper Date: Sun, 8 Mar 2020 17:48:40 +0100 Subject: [PATCH 42/46] arm64: dts: allwinner: h6: orangepi: Enable HDMI Both, OrangePi One Plus and OrangePi Lite 2 have HDMI output. Enable it in common DTSI. Signed-off-by: Marcus Cooper [patch split and commit message] Signed-off-by: Jernej Skrabec Reviewed-by: Christopher Obbard Tested-by: Christopher Obbard Signed-off-by: Maxime Ripard --- .../dts/allwinner/sun50i-h6-orangepi.dtsi | 26 +++++++++++++++++++ 1 file changed, 26 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi index 37fc3f3697f7..9287976c4a50 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi @@ -20,6 +20,18 @@ chosen { stdout-path = "serial0:115200n8"; }; + connector { + compatible = "hdmi-connector"; + type = "a"; + ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */ + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + ext_osc32k: ext_osc32k_clk { #clock-cells = <0>; compatible = "fixed-clock"; @@ -52,6 +64,10 @@ reg_vcc5v: vcc5v { }; }; +&de { + status = "okay"; +}; + &ehci0 { status = "okay"; }; @@ -65,6 +81,16 @@ &gpu { status = "okay"; }; +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &mmc0 { vmmc-supply = <®_cldo1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; From da180322582bd9db07f29e6d4a2d170afde0703f Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Sat, 25 Jan 2020 00:20:09 +0100 Subject: [PATCH 43/46] ARM: dts: sunxi: Fix DE2 clocks register range As it can be seen from DE2 manual, clock range is 0x10000. Fix it. Signed-off-by: Jernej Skrabec Fixes: 73f122c82775 ("ARM: dts: sun8i: a83t: Add display pipeline") Fixes: 05a43a262d03 ("ARM: dts: sun8i: r40: Add HDMI pipeline") Fixes: 21b299209330 ("ARM: sun8i: v3s: add device nodes for DE2 display pipeline") Fixes: d8c6f1f0295c ("ARM: sun8i: h3/h5: add DE2 CCU device node for H3") [wens@csie.org: added fixes tags] Signed-off-by: Chen-Yu Tsai --- arch/arm/boot/dts/sun8i-a83t.dtsi | 2 +- arch/arm/boot/dts/sun8i-r40.dtsi | 2 +- arch/arm/boot/dts/sun8i-v3s.dtsi | 2 +- arch/arm/boot/dts/sunxi-h3-h5.dtsi | 2 +- 4 files changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi index 53c2b6a836f2..92c69534d1e5 100644 --- a/arch/arm/boot/dts/sun8i-a83t.dtsi +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi @@ -314,7 +314,7 @@ soc { display_clocks: clock@1000000 { compatible = "allwinner,sun8i-a83t-de2-clk"; - reg = <0x01000000 0x100000>; + reg = <0x01000000 0x10000>; clocks = <&ccu CLK_BUS_DE>, <&ccu CLK_PLL_DE>; clock-names = "bus", diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi index d5442b5b6fd2..b2dd00a8eb9d 100644 --- a/arch/arm/boot/dts/sun8i-r40.dtsi +++ b/arch/arm/boot/dts/sun8i-r40.dtsi @@ -136,7 +136,7 @@ soc { display_clocks: clock@1000000 { compatible = "allwinner,sun8i-r40-de2-clk", "allwinner,sun8i-h3-de2-clk"; - reg = <0x01000000 0x100000>; + reg = <0x01000000 0x10000>; clocks = <&ccu CLK_BUS_DE>, <&ccu CLK_DE>; clock-names = "bus", diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi index 81ea50838cd5..e5312869c0d2 100644 --- a/arch/arm/boot/dts/sun8i-v3s.dtsi +++ b/arch/arm/boot/dts/sun8i-v3s.dtsi @@ -105,7 +105,7 @@ soc { display_clocks: clock@1000000 { compatible = "allwinner,sun8i-v3s-de2-clk"; - reg = <0x01000000 0x100000>; + reg = <0x01000000 0x10000>; clocks = <&ccu CLK_BUS_DE>, <&ccu CLK_DE>; clock-names = "bus", diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi index ed3908849111..d5516019e0f6 100644 --- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi @@ -114,7 +114,7 @@ soc { display_clocks: clock@1000000 { /* compatible is in per SoC .dtsi file */ - reg = <0x01000000 0x100000>; + reg = <0x01000000 0x10000>; clocks = <&ccu CLK_BUS_DE>, <&ccu CLK_DE>; clock-names = "bus", From 3e9a1a8b7f811de3eb1445d72f68766b704ad17c Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Sat, 25 Jan 2020 00:20:10 +0100 Subject: [PATCH 44/46] arm64: dts: allwinner: a64: Fix display clock register range Register range of display clocks is 0x10000, as it can be seen from DE2 documentation. Fix it. Signed-off-by: Jernej Skrabec Fixes: 2c796fc8f5dbd ("arm64: dts: allwinner: a64: add necessary device tree nodes for DE2 CCU") [wens@csie.org: added fixes tag] Signed-off-by: Chen-Yu Tsai --- arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi index 990de71ca048..8571f4aeaeb8 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi @@ -264,7 +264,7 @@ bus@1000000 { display_clocks: clock@0 { compatible = "allwinner,sun50i-a64-de2-clk"; - reg = <0x0 0x100000>; + reg = <0x0 0x10000>; clocks = <&ccu CLK_BUS_DE>, <&ccu CLK_DE>; clock-names = "bus", From dbf72a8c014728691f95a3fc9a463f9bdeb8c3fb Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Sat, 25 Jan 2020 00:20:13 +0100 Subject: [PATCH 45/46] ARM: dts: sun8i: a83t: Add device node for rotation core Allwinner A83T contains rotation core. Add a node for it. Signed-off-by: Jernej Skrabec Signed-off-by: Chen-Yu Tsai --- arch/arm/boot/dts/sun8i-a83t.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi index 92c69534d1e5..ff29458235ee 100644 --- a/arch/arm/boot/dts/sun8i-a83t.dtsi +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi @@ -324,6 +324,17 @@ display_clocks: clock@1000000 { #reset-cells = <1>; }; + rotate: rotate@1020000 { + compatible = "allwinner,sun8i-a83t-de2-rotate"; + reg = <0x1020000 0x10000>; + interrupts = ; + clocks = <&display_clocks CLK_BUS_ROT>, + <&display_clocks CLK_ROT>; + clock-names = "bus", + "mod"; + resets = <&display_clocks RST_ROT>; + }; + mixer0: mixer@1100000 { compatible = "allwinner,sun8i-a83t-de2-mixer-0"; reg = <0x01100000 0x100000>; From 048cdfceebb762ccbec7a11e1f1fb1c170c1e669 Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Sat, 25 Jan 2020 00:20:14 +0100 Subject: [PATCH 46/46] arm64: dts: allwinner: a64: add node for rotation core Allwinner A64 contains rotation core compatible to A83T. Add a node for it. Signed-off-by: Jernej Skrabec Signed-off-by: Chen-Yu Tsai --- arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi index 8571f4aeaeb8..31143fe64d91 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi @@ -274,6 +274,18 @@ display_clocks: clock@0 { #reset-cells = <1>; }; + rotate: rotate@20000 { + compatible = "allwinner,sun50i-a64-de2-rotate", + "allwinner,sun8i-a83t-de2-rotate"; + reg = <0x20000 0x10000>; + interrupts = ; + clocks = <&display_clocks CLK_BUS_ROT>, + <&display_clocks CLK_ROT>; + clock-names = "bus", + "mod"; + resets = <&display_clocks RST_ROT>; + }; + mixer0: mixer@100000 { compatible = "allwinner,sun50i-a64-de2-mixer-0"; reg = <0x100000 0x100000>;