mirror of
https://github.com/torvalds/linux.git
synced 2026-09-27 02:22:02 +02:00
arm64: dts: rockchip: Add LCKFB Taishan Pi 3M
Add the device tree for LCKFB Taishan Pi 3M, a board based on the Rockchip RK3576 SoC. The board schematics are available at: https://oshwhub.com/li-chuang-kai-fa-ban/project_gzzvrwqn Describe the RK806 supplies, eMMC, recovery key, RTC, SD card, Gigabit Ethernet, USB Type-A hosts, source-only USB Type-C host, mSATA, HDMI video and audio, AP6256 Wi-Fi and Bluetooth, status LED, thermal sensors, and debug UART. The MAE0621A PHY CLKOUT supplies the GMAC reference-clock input, so request its validated 125 MHz setting. The following interfaces were tested on the hardware: eMMC, RTC register access, recovery key, SD card, 1GbE, USB 2.0 Type-A storage, USB 3.0 Type-A 5 Gbit/s enumeration and 64 MiB storage I/O, USB-C source/host enumeration in both orientations, mSATA, HDMI video and audio, AP6256 2.4/5 GHz Wi-Fi scan, WPA2 association, ping and bidirectional throughput, Bluetooth firmware load and HCI bring-up, and UART0. Bluetooth active discovery was additionally exercised during bring-up. Signed-off-by: Liu Changjie <liucj1228@outlook.com> Link: https://patch.msgid.link/MN0PR19MB6091D3101FD2D8F940F0CE4DACF92@MN0PR19MB6091.namprd19.prod.outlook.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This commit is contained in:
Liu Changjie
Heiko Stuebner
parent
0c9d80d247
commit
c748c71d3b
|
|
@ -173,6 +173,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-evb1-v10.dtb
|
|||
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-evb1-v10-pcie1.dtbo
|
||||
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-evb2-v10.dtb
|
||||
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-khadas-edge-2l.dtb
|
||||
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-lckfb-tspi-3m.dtb
|
||||
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-luckfox-omni3576.dtb
|
||||
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-nanopi-m5.dtb
|
||||
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-nanopi-r76s.dtb
|
||||
|
|
|
|||
997
arch/arm64/boot/dts/rockchip/rk3576-lckfb-tspi-3m.dts
Normal file
997
arch/arm64/boot/dts/rockchip/rk3576-lckfb-tspi-3m.dts
Normal file
|
|
@ -0,0 +1,997 @@
|
|||
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||
/*
|
||||
* Copyright (c) 2026 LCKFB
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
#include <dt-bindings/pinctrl/rockchip.h>
|
||||
#include <dt-bindings/soc/rockchip,vop2.h>
|
||||
#include <dt-bindings/usb/pd.h>
|
||||
#include "rk3576.dtsi"
|
||||
|
||||
/ {
|
||||
model = "LCKFB TaishanPi 3M";
|
||||
compatible = "lckfb,tspi-3m-rk3576", "rockchip,rk3576";
|
||||
|
||||
aliases {
|
||||
mmc0 = &sdhci;
|
||||
mmc1 = &sdmmc;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:1500000n8";
|
||||
};
|
||||
|
||||
adc-keys {
|
||||
compatible = "adc-keys";
|
||||
io-channels = <&saradc 1>;
|
||||
io-channel-names = "buttons";
|
||||
keyup-threshold-microvolt = <1800000>;
|
||||
poll-interval = <100>;
|
||||
|
||||
button-recovery {
|
||||
label = "Recovery";
|
||||
linux,code = <KEY_VENDOR>;
|
||||
press-threshold-microvolt = <18000>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-0 {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_HEARTBEAT;
|
||||
gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "heartbeat";
|
||||
};
|
||||
};
|
||||
|
||||
hdmi-con {
|
||||
compatible = "hdmi-connector";
|
||||
type = "a";
|
||||
|
||||
port {
|
||||
hdmi_con_in: endpoint {
|
||||
remote-endpoint = <&hdmi_out_con>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
vcc_5v0_usb2_host: regulator-vcc-5v0-usb2-host {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio2 RK_PB5 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&usb2_host_pwren>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-name = "vcc_5v0_usb2_host";
|
||||
vin-supply = <&vcc_5v0_sys>;
|
||||
};
|
||||
|
||||
vcc_5v0_usb3_host: regulator-vcc-5v0-usb3-host {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 RK_PC3 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&usb3_host_pwren>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-name = "vcc_5v0_usb3_host";
|
||||
vin-supply = <&vcc_5v0_sys>;
|
||||
};
|
||||
|
||||
vcc_5v0_typec: regulator-vcc-5v0-typec {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&typec_vbus_en>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-name = "vcc_5v0_typec";
|
||||
vin-supply = <&vcc_5v0_sys>;
|
||||
};
|
||||
|
||||
vcc_5v0_sys: regulator-vcc-5v0-sys {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc_5v0_sys";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
};
|
||||
|
||||
vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc_1v1_nldo_s3";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <1100000>;
|
||||
regulator-max-microvolt = <1100000>;
|
||||
vin-supply = <&vcc_5v0_sys>;
|
||||
};
|
||||
|
||||
vcc_2v0_pldo_s3: regulator-vcc-2v0-pldo-s3 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc_2v0_pldo_s3";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <2000000>;
|
||||
regulator-max-microvolt = <2000000>;
|
||||
vin-supply = <&vcc_5v0_sys>;
|
||||
};
|
||||
|
||||
vcc_3v3_minipcie: regulator-vcc-3v3-minipcie {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
gpio = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&minipcie_pwren>;
|
||||
regulator-boot-on;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-name = "vcc_3v3_minipcie";
|
||||
startup-delay-us = <5000>;
|
||||
vin-supply = <&vcc_5v0_sys>;
|
||||
};
|
||||
|
||||
vcc_3v3_wl: regulator-3v3-wl {
|
||||
compatible = "regulator-fixed";
|
||||
gpio = <&gpio0 RK_PD1 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&wifi_pwren_l>;
|
||||
regulator-boot-on;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-name = "vcc_3v3_wl";
|
||||
vin-supply = <&vcc_3v3_s0>;
|
||||
};
|
||||
|
||||
vcc_3v3_s0: regulator-vcc-3v3-s0 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc_3v3_s0";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
vin-supply = <&vcc_3v3_s3>;
|
||||
};
|
||||
|
||||
sdio_pwrseq: sdio-pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
clock-names = "ext_clock";
|
||||
clocks = <&hym8563>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&wifi_reg_on_h>;
|
||||
post-power-on-delay-ms = <200>;
|
||||
reset-gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb_a_3_0: usb-a-connector-0 {
|
||||
compatible = "usb-a-connector";
|
||||
label = "USB 3.0 Type-A";
|
||||
vbus-supply = <&vcc_5v0_usb3_host>;
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
|
||||
usb_a_3_0_hs: endpoint {
|
||||
remote-endpoint = <&usb_hub_port1>;
|
||||
};
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
|
||||
usb_a_3_0_ss: endpoint {
|
||||
remote-endpoint = <&usb_drd1_ss>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
usb_a_2_0_1: usb-a-connector-1 {
|
||||
compatible = "usb-a-connector";
|
||||
label = "USB 2.0 Type-A 1";
|
||||
vbus-supply = <&vcc_5v0_usb3_host>;
|
||||
|
||||
port {
|
||||
usb_a_2_0_1_hs: endpoint {
|
||||
remote-endpoint = <&usb_hub_port2>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
usb_a_2_0_2: usb-a-connector-2 {
|
||||
compatible = "usb-a-connector";
|
||||
label = "USB 2.0 Type-A 2";
|
||||
vbus-supply = <&vcc_5v0_usb2_host>;
|
||||
|
||||
port {
|
||||
usb_a_2_0_2_hs: endpoint {
|
||||
remote-endpoint = <&usb_hub_port3>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
usb_a_2_0_3: usb-a-connector-3 {
|
||||
compatible = "usb-a-connector";
|
||||
label = "USB 2.0 Type-A 3";
|
||||
vbus-supply = <&vcc_5v0_usb2_host>;
|
||||
|
||||
port {
|
||||
usb_a_2_0_3_hs: endpoint {
|
||||
remote-endpoint = <&usb_hub_port4>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&combphy0_ps {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&combphy1_psu {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cpu_b0 {
|
||||
cpu-supply = <&vdd_cpu_big_s0>;
|
||||
};
|
||||
|
||||
&cpu_b1 {
|
||||
cpu-supply = <&vdd_cpu_big_s0>;
|
||||
};
|
||||
|
||||
&cpu_b2 {
|
||||
cpu-supply = <&vdd_cpu_big_s0>;
|
||||
};
|
||||
|
||||
&cpu_b3 {
|
||||
cpu-supply = <&vdd_cpu_big_s0>;
|
||||
};
|
||||
|
||||
&cpu_l0 {
|
||||
cpu-supply = <&vdd_cpu_lit_s0>;
|
||||
};
|
||||
|
||||
&cpu_l1 {
|
||||
cpu-supply = <&vdd_cpu_lit_s0>;
|
||||
};
|
||||
|
||||
&cpu_l2 {
|
||||
cpu-supply = <&vdd_cpu_lit_s0>;
|
||||
};
|
||||
|
||||
&cpu_l3 {
|
||||
cpu-supply = <&vdd_cpu_lit_s0>;
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
clock_in_out = "input";
|
||||
phy-handle = <&rgmii_phy0>;
|
||||
/* RX delay is added by the PHY, TX delay by the GMAC. */
|
||||
phy-mode = "rgmii-rxid";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <ð0m0_miim
|
||||
ð0m0_tx_bus2
|
||||
ð0m0_rx_bus2
|
||||
ð0m0_rgmii_clk
|
||||
ð0m0_rgmii_bus
|
||||
ð0m0_mclk>;
|
||||
tx_delay = <0x24>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&hdmi {
|
||||
/* The external level shifters must be on for TMDS operation. */
|
||||
frl-enable-gpios = <&gpio4 RK_PC6 GPIO_ACTIVE_LOW>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&hdmi_in {
|
||||
hdmi_in_vp0: endpoint {
|
||||
remote-endpoint = <&vp0_out_hdmi>;
|
||||
};
|
||||
};
|
||||
|
||||
&hdmi_out {
|
||||
hdmi_out_con: endpoint {
|
||||
remote-endpoint = <&hdmi_con_in>;
|
||||
};
|
||||
};
|
||||
|
||||
&hdmi_sound {
|
||||
simple-audio-card,mclk-fs = <128>;
|
||||
status = "okay";
|
||||
|
||||
simple-audio-card,cpu {
|
||||
dai-tdm-slot-num = <2>;
|
||||
dai-tdm-slot-width = <32>;
|
||||
};
|
||||
};
|
||||
|
||||
&hdptxphy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
status = "okay";
|
||||
|
||||
pmic@23 {
|
||||
compatible = "rockchip,rk806";
|
||||
reg = <0x23>;
|
||||
#gpio-cells = <2>;
|
||||
gpio-controller;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_pins
|
||||
&rk806_dvs1_null
|
||||
&rk806_dvs2_null
|
||||
&rk806_dvs3_null>;
|
||||
system-power-controller;
|
||||
vcc1-supply = <&vcc_5v0_sys>;
|
||||
vcc2-supply = <&vcc_5v0_sys>;
|
||||
vcc3-supply = <&vcc_5v0_sys>;
|
||||
vcc4-supply = <&vcc_5v0_sys>;
|
||||
vcc5-supply = <&vcc_5v0_sys>;
|
||||
vcc6-supply = <&vcc_5v0_sys>;
|
||||
vcc7-supply = <&vcc_5v0_sys>;
|
||||
vcc8-supply = <&vcc_5v0_sys>;
|
||||
vcc9-supply = <&vcc_5v0_sys>;
|
||||
vcc10-supply = <&vcc_5v0_sys>;
|
||||
vcc11-supply = <&vcc_2v0_pldo_s3>;
|
||||
vcc12-supply = <&vcc_5v0_sys>;
|
||||
vcc13-supply = <&vcc_1v1_nldo_s3>;
|
||||
vcc14-supply = <&vcc_1v1_nldo_s3>;
|
||||
vcca-supply = <&vcc_5v0_sys>;
|
||||
|
||||
rk806_dvs1_null: dvs1-null-pins {
|
||||
pins = "gpio_pwrctrl1";
|
||||
function = "pin_fun0";
|
||||
};
|
||||
|
||||
rk806_dvs2_null: dvs2-null-pins {
|
||||
pins = "gpio_pwrctrl2";
|
||||
function = "pin_fun0";
|
||||
};
|
||||
|
||||
rk806_dvs3_null: dvs3-null-pins {
|
||||
pins = "gpio_pwrctrl3";
|
||||
function = "pin_fun0";
|
||||
};
|
||||
|
||||
regulators {
|
||||
vdd_cpu_big_s0: dcdc-reg1 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-enable-ramp-delay = <400>;
|
||||
regulator-min-microvolt = <550000>;
|
||||
regulator-max-microvolt = <950000>;
|
||||
regulator-name = "vdd_cpu_big_s0";
|
||||
regulator-ramp-delay = <12500>;
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdd_npu_s0: dcdc-reg2 {
|
||||
regulator-boot-on;
|
||||
regulator-enable-ramp-delay = <400>;
|
||||
regulator-min-microvolt = <550000>;
|
||||
regulator-max-microvolt = <950000>;
|
||||
regulator-name = "vdd_npu_s0";
|
||||
regulator-ramp-delay = <12500>;
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdd_cpu_lit_s0: dcdc-reg3 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <550000>;
|
||||
regulator-max-microvolt = <950000>;
|
||||
regulator-name = "vdd_cpu_lit_s0";
|
||||
regulator-ramp-delay = <12500>;
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vcc_3v3_s3: dcdc-reg4 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-name = "vcc_3v3_s3";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdd_gpu_s0: dcdc-reg5 {
|
||||
regulator-boot-on;
|
||||
regulator-enable-ramp-delay = <400>;
|
||||
regulator-min-microvolt = <550000>;
|
||||
regulator-max-microvolt = <900000>;
|
||||
regulator-name = "vdd_gpu_s0";
|
||||
regulator-ramp-delay = <12500>;
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vddq_ddr_s0: dcdc-reg6 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-name = "vddq_ddr_s0";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdd_logic_s0: dcdc-reg7 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <550000>;
|
||||
regulator-max-microvolt = <800000>;
|
||||
regulator-name = "vdd_logic_s0";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vcc_1v8_s3: dcdc-reg8 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-name = "vcc_1v8_s3";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdd2_ddr_s3: dcdc-reg9 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-name = "vdd2_ddr_s3";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdd_ddr_s0: dcdc-reg10 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <550000>;
|
||||
regulator-max-microvolt = <1200000>;
|
||||
regulator-name = "vdd_ddr_s0";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vcca_1v8_s0: pldo-reg1 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-name = "vcca_1v8_s0";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vcca1v8_pldo2_s0: pldo-reg2 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-name = "vcca1v8_pldo2_s0";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdda_1v2_s0: pldo-reg3 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <1200000>;
|
||||
regulator-max-microvolt = <1200000>;
|
||||
regulator-name = "vdda_1v2_s0";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vcca_3v3_s0: pldo-reg4 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-name = "vcca_3v3_s0";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vccio_sd_s0: pldo-reg5 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-name = "vccio_sd_s0";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vcca1v8_pldo6_s3: pldo-reg6 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-name = "vcca1v8_pldo6_s3";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdd_0v75_s3: nldo-reg1 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <750000>;
|
||||
regulator-max-microvolt = <750000>;
|
||||
regulator-name = "vdd_0v75_s3";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdda_ddr_pll_s0: nldo-reg2 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <850000>;
|
||||
regulator-max-microvolt = <850000>;
|
||||
regulator-name = "vdda_ddr_pll_s0";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdda_hdmi_s0: nldo-reg3 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <837500>;
|
||||
regulator-max-microvolt = <837500>;
|
||||
regulator-name = "vdda_hdmi_s0";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdda_0v85_s0: nldo-reg4 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <850000>;
|
||||
regulator-max-microvolt = <850000>;
|
||||
regulator-name = "vdda_0v85_s0";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdda_0v75_s0: nldo-reg5 {
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <750000>;
|
||||
regulator-max-microvolt = <750000>;
|
||||
regulator-name = "vdda_0v75_s0";
|
||||
|
||||
regulator-state-mem {
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&i2c2 {
|
||||
status = "okay";
|
||||
|
||||
typec@22 {
|
||||
compatible = "fcs,fusb302";
|
||||
reg = <0x22>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <RK_PB4 IRQ_TYPE_LEVEL_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&fusb302_int>;
|
||||
vbus-supply = <&vcc_5v0_typec>;
|
||||
|
||||
connector {
|
||||
compatible = "usb-c-connector";
|
||||
data-role = "host";
|
||||
label = "USB-C";
|
||||
power-role = "source";
|
||||
source-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)>;
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
|
||||
usb_c_hs: endpoint {
|
||||
remote-endpoint = <&usb_drd0_hs>;
|
||||
};
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
|
||||
usb_c_ss: endpoint {
|
||||
remote-endpoint = <&usbdp_phy_ep>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
hym8563: rtc@51 {
|
||||
compatible = "haoyu,hym8563";
|
||||
reg = <0x51>;
|
||||
#clock-cells = <0>;
|
||||
clock-output-names = "hym8563";
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <RK_PA5 IRQ_TYPE_LEVEL_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rtc_int_l>;
|
||||
wakeup-source;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
rgmii_phy0: ethernet-phy@1 {
|
||||
compatible = "ethernet-phy-id7b74.4412";
|
||||
reg = <0x1>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&gmac0_phy_reset>;
|
||||
reset-assert-us = <20000>;
|
||||
reset-deassert-us = <100000>;
|
||||
reset-gpios = <&gpio2 RK_PB3 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
ethernet {
|
||||
gmac0_phy_reset: gmac0-phy-reset {
|
||||
rockchip,pins = <2 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
|
||||
minipcie {
|
||||
minipcie_pwren: minipcie-pwren {
|
||||
rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
|
||||
rtc {
|
||||
rtc_int_l: rtc-int-l {
|
||||
rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
|
||||
};
|
||||
};
|
||||
|
||||
wireless-bluetooth {
|
||||
bt_host_wake_h: bt-host-wake-h {
|
||||
rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_down>;
|
||||
};
|
||||
|
||||
bt_reg_on_h: bt-reg-on-h {
|
||||
rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
|
||||
bt_wake_h: bt-wake-h {
|
||||
rockchip,pins = <1 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
|
||||
wireless-wlan {
|
||||
wifi_host_wake_h: wifi-host-wake-h {
|
||||
rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>;
|
||||
};
|
||||
|
||||
wifi_pwren_l: wifi-pwren-l {
|
||||
rockchip,pins = <0 RK_PD1 RK_FUNC_GPIO &pcfg_pull_up>;
|
||||
};
|
||||
|
||||
wifi_reg_on_h: wifi-reg-on-h {
|
||||
rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
|
||||
};
|
||||
};
|
||||
|
||||
sdmmc {
|
||||
sdmmc0_det_l: sdmmc0-det-l {
|
||||
rockchip,pins = <0 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>;
|
||||
};
|
||||
};
|
||||
|
||||
usb-host {
|
||||
usb2_host_pwren: usb2-host-pwren {
|
||||
rockchip,pins = <2 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
|
||||
usb3_host_pwren: usb3-host-pwren {
|
||||
rockchip,pins = <0 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
|
||||
usb-typec {
|
||||
fusb302_int: fusb302-int {
|
||||
rockchip,pins = <0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>;
|
||||
};
|
||||
|
||||
typec_vbus_en: typec-vbus-en {
|
||||
rockchip,pins = <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&sai6 {
|
||||
rockchip,sai-tx-route = <0>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&saradc {
|
||||
vref-supply = <&vcca1v8_pldo2_s0>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&sata0 {
|
||||
target-supply = <&vcc_3v3_minipcie>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&sdio {
|
||||
bus-width = <4>;
|
||||
cap-sd-highspeed;
|
||||
cap-sdio-irq;
|
||||
keep-power-in-suspend;
|
||||
max-frequency = <100000000>;
|
||||
mmc-pwrseq = <&sdio_pwrseq>;
|
||||
no-mmc;
|
||||
no-sd;
|
||||
non-removable;
|
||||
sd-uhs-sdr104;
|
||||
vmmc-supply = <&vcc_3v3_wl>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
wifi@1 {
|
||||
compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-fmac";
|
||||
reg = <1>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <RK_PB0 IRQ_TYPE_LEVEL_HIGH>;
|
||||
interrupt-names = "host-wake";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&wifi_host_wake_h>;
|
||||
};
|
||||
};
|
||||
|
||||
&sdmmc {
|
||||
bus-width = <4>;
|
||||
cap-sd-highspeed;
|
||||
cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
|
||||
disable-wp;
|
||||
max-frequency = <50000000>;
|
||||
no-mmc;
|
||||
no-sdio;
|
||||
pinctrl-names = "default";
|
||||
/* GPIO0_B6/SDMMC0_PWREN is not connected on this board. */
|
||||
pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_det_l &sdmmc0_bus4>;
|
||||
vmmc-supply = <&vcc_3v3_s0>;
|
||||
vqmmc-supply = <&vccio_sd_s0>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&sdhci {
|
||||
bus-width = <8>;
|
||||
full-pwr-cycle-in-suspend;
|
||||
mmc-hs400-1_8v;
|
||||
mmc-hs400-enhanced-strobe;
|
||||
no-sd;
|
||||
no-sdio;
|
||||
non-removable;
|
||||
vmmc-supply = <&vcc_3v3_s3>;
|
||||
vqmmc-supply = <&vcc_1v8_s3>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tsadc {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart6 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart6m1_xfer &uart6m1_ctsn &uart6m1_rtsn>;
|
||||
uart-has-rtscts;
|
||||
status = "okay";
|
||||
|
||||
bluetooth {
|
||||
compatible = "brcm,bcm4345c5";
|
||||
clocks = <&hym8563>;
|
||||
clock-names = "lpo";
|
||||
device-wakeup-gpios = <&gpio1 RK_PD4 GPIO_ACTIVE_HIGH>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <RK_PB1 IRQ_TYPE_LEVEL_HIGH>;
|
||||
interrupt-names = "host-wakeup";
|
||||
max-speed = <1500000>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&bt_host_wake_h &bt_reg_on_h &bt_wake_h>;
|
||||
shutdown-gpios = <&gpio1 RK_PC7 GPIO_ACTIVE_HIGH>;
|
||||
vbat-supply = <&vcc_3v3_wl>;
|
||||
};
|
||||
};
|
||||
|
||||
&u2phy0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&u2phy0_otg {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&u2phy1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&u2phy1_otg {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbdp_phy {
|
||||
mode-switch;
|
||||
orientation-switch;
|
||||
status = "okay";
|
||||
|
||||
port {
|
||||
usbdp_phy_ep: endpoint {
|
||||
remote-endpoint = <&usb_c_ss>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb_drd0_dwc3 {
|
||||
usb-role-switch;
|
||||
status = "okay";
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
|
||||
usb_drd0_hs: endpoint {
|
||||
remote-endpoint = <&usb_c_hs>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb_drd1_dwc3 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
dr_mode = "host";
|
||||
status = "okay";
|
||||
|
||||
usb_hub: hub@1 {
|
||||
compatible = "usb1a40,0201";
|
||||
reg = <1>;
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
|
||||
usb_hub_port1: endpoint {
|
||||
remote-endpoint = <&usb_a_3_0_hs>;
|
||||
};
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
|
||||
usb_hub_port2: endpoint {
|
||||
remote-endpoint = <&usb_a_2_0_1_hs>;
|
||||
};
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
|
||||
usb_hub_port3: endpoint {
|
||||
remote-endpoint = <&usb_a_2_0_2_hs>;
|
||||
};
|
||||
};
|
||||
|
||||
port@4 {
|
||||
reg = <4>;
|
||||
|
||||
usb_hub_port4: endpoint {
|
||||
remote-endpoint = <&usb_a_2_0_3_hs>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
|
||||
usb_drd1_ss: endpoint {
|
||||
remote-endpoint = <&usb_a_3_0_ss>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&vop {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&vop_mmu {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&vp0 {
|
||||
vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
|
||||
reg = <ROCKCHIP_VOP2_EP_HDMI0>;
|
||||
remote-endpoint = <&hdmi_in_vp0>;
|
||||
};
|
||||
};
|
||||
Loading…
Reference in New Issue
Block a user