diff --git a/Documentation/devicetree/bindings/i3c/i3c.yaml b/Documentation/devicetree/bindings/i3c/i3c.yaml
index e25fa72fd785..5603f2e7807d 100644
--- a/Documentation/devicetree/bindings/i3c/i3c.yaml
+++ b/Documentation/devicetree/bindings/i3c/i3c.yaml
@@ -31,10 +31,12 @@ properties:
       described in the device tree, which in turn means we have to describe
       I3C devices.
 
-      Another use case for describing an I3C device in the device tree is when
-      this I3C device has a static I2C address and we want to assign it a
-      specific I3C dynamic address before the DAA takes place (so that other
-      devices on the bus can't take this dynamic address).
+      Other use-cases for describing an I3C device in the device tree are:
+      - When the I3C device has a static I2C address and we want to assign
+        it a specific I3C dynamic address before the DAA takes place (so
+        that other devices on the bus can't take this dynamic address).
+      - When the I3C device requires SETAASA for its discovery and uses a
+        pre-defined static address.
 
   "#size-cells":
     const: 0
@@ -145,7 +147,31 @@ patternProperties:
           Dynamic address to be assigned to this device. In case static address is
           present (first cell of the reg property != 0), this address is assigned
           through SETDASA. If static address is not present, this address is assigned
-          through SETNEWDA after assigning a temporary address via ENTDAA.
+          through SETNEWDA after assigning a temporary address via ENTDAA. If
+          SETAASA is used, this property is not used, and the static address itself
+          becomes the dynamic address.
+
+      mipi-i3c-static-method:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0x1
+        maximum: 0x7
+        default: 1
+        description: |
+          Bitmap describing which methods of Dynamic Address Assignment from a
+          static address are supported by this I3C Target. For each defined bit
+          position, a set bit indicates support for that method and a cleared
+          bit indicates lack of support.
+
+            Bit 0: SETDASA CCC (Direct)
+            Bit 1: SETAASA CCC (Broadcast)
+            Bit 2: Other CCC (vendor / standards extension)
+            All other bits are reserved.
+
+          This property follows the MIPI I3C specification. The primary use
+          of this property is to indicate support for SETAASA, i.e Bit 1, but
+          will allow other values mentioned in the specification so that it
+          mirrors the specification. SETDASA will remain as the default method
+          even if this property is not present.
 
     required:
       - reg
diff --git a/include/dt-bindings/i3c/i3c.h b/include/dt-bindings/i3c/i3c.h
index 373439218bba..78b8c634aad8 100644
--- a/include/dt-bindings/i3c/i3c.h
+++ b/include/dt-bindings/i3c/i3c.h
@@ -13,4 +13,8 @@
 #define I2C_NO_FILTER_HIGH_FREQUENCY    (1 << 5)
 #define I2C_NO_FILTER_LOW_FREQUENCY     (2 << 5)
 
+#define I3C_ADDR_METHOD_SETDASA     (1 << 0)
+#define I3C_ADDR_METHOD_SETAASA     (1 << 1)
+#define I3C_ADDR_METHOD_VENDOR      (1 << 2)
+
 #endif